How it Works
SIG SAUER
Loading...
SP2022М
User Manual
64 pgs1.36 Mb0

SIG SAUER SP2022, SP2022М User Manual

Download
Page 1
®
SP2022 SP2022®M
OWNERS MANUAL: HANDLING & SAFETY INSTRUCTIONS
READ THE INSTRUCTIONS AND WARNINGS IN THIS MANUAL CAREFULLY
BEFORE USING THIS FIREARM; DO NOT DISCARD THIS MANUAL.
This instruction manual should always accompany this firearm and be transferred with it upon
ownership, or when the firearm is loaned or presented to another person.
Page 2
Certain states require, by law, that their own specified warning notices, in larger­than-normal type be conspicuously included by the manufacturer, distributor, or retail dealer with firearms sold in that state. SIG SAUER sells its products in compliance with applicable laws and regulations. Because our products may be sold in these states, we include the following:
CALIFORNIA:
State-By-State Warnings
WARNING
“Children are attracted to and can operate firearms that can cause severe injuries or death. Prevent child access by always keeping guns locked away and unloaded when not in use. If you keep a loaded firearm where a child obtains and improperly uses it, you may be fined or sent to prison.”
ADVERTENCIA
“A los niños atraen las amas de fuego y las pueden hacer funcionar. Ellos pueden causarse lesions graves y la muerte. Evite que los niños tengan accesso a las armas de fuego guardándolas siepre con llave y descargadas cuando no las esté utilizando. Si usted tiene una arma de fuego cargada en un lugar en que un niño tiene accesso a ella y la usa indebidamente, le pueden dar una multa o enviarlo a la carcel.”
CONNECTICUT:
“UNLAWFUL STORAGE OF A LOADED FIREARM MAY RESULT IN IMPRISONMENT OR FINE.”
FLORIDA:
“IT IS UNLAWFUL, AND PUNISHABLE BY IMPRISONMENT AND FINE, FOR ANY ADULT TO STORE OR LEAVE A FIREARM IN ANY PLACE WITHIN THE REACH OR EASY ACCESS OF A MINOR UNDER 18 YEARS OF AGE OR TO KNOWINGLY SELL OR OTHERWISE TRANSFER OWNERSHIP OR POSSESSION OF A FIREARM TO A MINOR OR A PERSON OF UNSOUND MIND.”
2
Page 3
MAINE:
“ENDANGERING THE WELFARE OF A CHILD IS A CRIME. IF YOU LEAVE A FIREARM AND AMMUNITION WITHIN EASY ACCESS OF A CHILD, YOU MAY BE SUBJECT TO FINE, IMPRISONMENT OR BOTH. KEEP FIREARMS AND AMMUNITION SEPARATE. KEEP FIREARMS AND AMMUNITION LOCKED UP. USE TRIGGER LOCKS.”
MARYLAND:
“WARNING: Children can operate firearms which may cause death or serious injury. It is a crime to store or leave a loaded firearm in any location where an individual knew or should have known that an unsupervised minor would gain access to the firearm. Store your firearm responsibly!”
MASSACHUSETTS:
“WARNING FROM THE MASSACHUSETTS ATTORNEY GENERAL: This handgun is not equipped with a device that fully blocks use by unauthorized users. More than 200,000 firearms like this one are stolen from their owners every year in the United States. In addition, there are more than a thousand suicides each year by younger children and teenagers who get access to firearms. Hundreds more die from accidental discharge. It is likely that many more children sustain serious wounds, or inflict such wounds accidentally on others. In order to limit the chance of such misuse, it is imperative that you keep this weapon locked in a secure place and take other steps necessary to limit the possibility of theft or accident. Failure to take reasonable preventative steps may result in innocent lives being lost, and in some circumstances may result in your liability for these deaths.”
“IT IS UNLAWFUL TO STORE OR KEEP A FIREARM, RIFLE, SHOTGUN OR MACHINE GUN IN ANY PLACE UNLESS THAT WEAPON IS EQUIPPED WITH A TAMPER RESISTANT SAFETY DEVICE OR IS STORED OR KEPT IN A SECURELY LOCKED CONTAINER.”
NEW JERSEY:
“IT IS A CRIMINAL OFFENSE TO LEAVE A LOADED FIREARM WITHIN EASY ACCESS OF A MINOR.”
3
Page 4
NEW YORK CITY, NY:
“THE USE OF A LOCKING DEVICE OR SAFETY LOCK IS ONLY ONE ASPECT OF RESPONSIBLE FIREARMS STORAGE. FOR INCREASED SAFETY, FIREARMS SHOULD BE STORED UNLOADED AND LOCKED IN A LOCATION THAT IS BOTH SEPARATE FROM THEIR AMMUNITION AND INACCESSIBLE TO CHILDREN AND OTHER UNAUTHORIZED PERSONS.”
NORTH CAROLINA:
Any person who resides in the same premises as a minor, owns or possesses a firearm, and stores or leaves the firearm (i) in a condition that the firearm can be discharged and (ii) in a manner that the person knew or should have known that an unsupervised minor would be able to gain access to the firearm, is guilty of a Class 1 misdemeanor if a minor gains access to the firearm without the lawful permission of the minor’s parents or a person having charge of the minor and the minor: (1) Possesses it in violation of G.S. 14-269.2(b) (2) Exhibits it in a public place in a careless, angry, or threatening manner; (3) Causes personal injury or death with it not in self defense; or (4) Uses it in the commission of a crime.
TEXAS:
“IT IS UNLAWFUL TO STORE, TRANSPORT, OR ABANDON AN UNSECURED FIREARM IN A PLACE WHERE CHILDREN ARE LIKELY TO BE AND CAN OBTAIN ACCESS TO THE FIREARM.”
WISCONSIN:
“IF YOU LEAVE A LOADED FIREARM WITHIN THE REACH OR EASY ACCESS OF A CHILD YOU MAY BE FINED OR IMPRISONED OR BOTH IF THE CHILD IMPROPERLY DISCHARGES, POSSESSES, OR EXHIBITS THE FIREARM.”
Please check with your licensed retailer, state police, or local police for additional warnings, which may be required by local law or regulation. Such regulations change constantly, and local authorities are in the best position to advise you on such legal matters.
4
Page 5
THE BASIC RULES OF SAFE FIREARMS HANDLING
1. ALWAYS treat every gun as if it were loaded.
2. ALWAYS be sure the barrel is clear of any obstruction.
3. ALWAYS be sure of your backstop, what lies beyond, and the safety of bystanders before you shoot.
4. ALWAYS use clean, dry, original factory-made ammunition of the proper type and caliber for your gun.
5. ALWAYS wear ear protection and safety glasses when shooting.
6. ALWAYS carry your gun so that you can control the direction of the muzzle if you fall or stumble.
7. NEVER shoot at a flat surface or water.
8. DO NOT leave an unattended gun loaded. Guns and ammunition should be stored separately, locked if possible, beyond the reach of children, careless adults, and unauthorized users.
9. NEVER allow your firearm to be used by anyone who has not read and understood this operator’s manual.
10. DO NOT point any gun, loaded or unloaded, at any undesired target.
11. NEVER fire your rifle near an animal unless it is trained to accept the noise: an animal’s startled reaction could injure it or cause an accident.
12. NEVER drink alcoholic beverages or take drugs before or during shooting, as your vision and judgment could be seriously impaired, making your gun handling unsafe.
5
Page 6
W
WARNING – LOCKING DEVICES
This firearm was originally sold with a key­operated locking device. While it can help provide secure storage for your unloaded firearm, any locking device can fail. All guns are designed to fire if they are loaded and the trigger is pulled. Therefore, never install the locking device inside the trigger guard or in any way that makes it possible to pull the trigger! Do not leave the keys in the lock.
The ultimate responsibility for secure storage of any firearm must depend upon its owner and his or her individual circumstances. Firearms should be stored unloaded, in a secure location, separate from their ammunition.
NEVER INSTALL THE LOCKING DEVICE INSIDE THE TRIGGER GUARD
To maximize effectiveness and reduce the chances of malfunction or damage to a firearm, ALWAYS refer to the locking device’s manufacturer directions for installation and removal of the device.
6
Page 7
FIREARMS SAFETY IS YOUR RESPONSIBILITY
This owner’s manual is designed to assist you in learning how to use and care for your SIG SAUER® pistol properly.
Only when you are certain that you fully understand this manual and can properly carry out its instructions, should you practice loading and firing your firearm with live ammunition. Having a gun in your possession is a full-time job; you cannot guess and you cannot forget. You must know how to use your firearm safely.
If you have any doubts about your ability to handle or use this firearm safely, you should seek supervised instruction. The Sig Sauer Academy™ provides all levels of firearms safety and skill training, from beginner to expert.
For more information contact:
www.sigsaueracademy.com • (603) 610-3400
Main campus: Epping, New Hampshire Satellite Facilities: Range 82, Midland, VA NRA Whittington Center, Raton, NM
SAFETY MUST BE THE FIRST AND CONSTANT CONSIDERATION OF EVERY PERSON WHO HANDLES FIREARMS AND AMMUNITION.
For more information about safety, responsible firearms ownership, and shooting
sports, contact:
National Rifle Association (NRA) of America
11250 Waples Mill Road, Fairfax, VA 22030-7400 • 1-800-672-3888
www.nra.com
7
Page 8
TABLE OF CONTENTS
Topic Page
State-By-State Warnings 2
The Basic Rules of Safe Firearms Handling 5
Locking Devices 6
Warnings of Great Importance 10
1.0 Safety Rules 11
1.1 Protect Your Eyes and Ears 11
2.0 Main Parts 12
2.1 SP2022 Technical Specifications 13
2.2 Mechanical Characteristics and Weapon Theory 14
2.3 Weapon Description 14
2.3.1 General 14
2.3.2 Principal Features 14
2.4 SP2022 M Manual Safety Model 15
2.5 Manual Safety Lock 15
2.6 Shock Protection 16
3.0 Ammunition 17
4.0 Handling 21
4.1 Preparation Instructions 21
4.2 Loading the Magazine 21
4.3 Loading the Pistol (Ready to Fire) 22
4.4 Reloading During Shooting 23
5.0 Firing 25
5.1 Clearing a Jam 26
5.2 Firing the Pistol 27
6.0 Unloading the Pistol 29
6.1 Unloading the Pistol (Magazine Not Empty) 29
6.2 Unloading the Pistol (Magazine Empty, Slide Open) 30
8
Page 9
Topic Page
7.0 Procedures in Case of Malfunction 32
7.1 Troubleshooting Guide 33
7.2 Minimize Malfunctions 34
8.0 Maintenance 35
8.1 Pistol Disassembly 35
8.2 Magazine Disassembly 38
8.3 Cleaning the Pistol 39
8.4 Pistol Assembly 40
8.5 Magazine Assembly 42
8.6 Function Verification 43
9.0 Pistol Adjustments 47
9.1 General Information 47
9.2 Magazine Catch Removal and Reversal 48
9.3 Changing the Grip Module 46
9.3.1 Disassembly 46
9.3.2 Assembly 48
10.0 Sights 51
10.1 General Information 51
10.2 Windage Adjustment 51
11.0 Transportation and Storage 53
12.0 Service and Parts Policy 54
12.1 Parts Policy 54
12.2 Service Policy 55
12.3 Shipping Firearms for Repair 55
12.4 Ordering Parts 57
13.0 Parts List 58 14 Parts Diagram 59
Warranty Information 60
9
Page 10
WARNINGS OF GREAT IMPORTANCE
ARE FOUND WITHIN THIS MANUAL
Locking Devices 6 Alterations 10 Safety 11 Ammunition 17, 20 Lodged Bullet 19 Lead Exposure 20 Loaded Pistol 24 Trigger 25 Malfunction 25 Handling 26 Dropped Pistol 26 Unloading 28, 31, 47
OTHER CAUTIONS AND WARNINGS APPEAR THROUGHOUT THE MANUAL
Jam 32, 34 Maintenance 35, 43 Disassembly 35, 38, 49 Cleaning 39 Assembly 40, 42 Inspection 46 Alterations 50 Sight Adjustment 51, 52 Storage 53 Parts Purchasers 54 Shipping 57
FIREARMS ARE DANGEROUS WEAPONS
READ THE INSTRUCTIONS AND WARNINGS
IN THIS MANUAL THOROUGHLY AND
CAREFULLY BEFORE USING.
W
WARNING – ALTERATIONS
This product was designed to function properly in its original condition. Alterations can make it unsafe. Do not alter any part or add or substitute any parts or accessories not manufactured by SIG SAUER Inc.
DO NOT ALTER ANY GUN
10
Page 11
1.0 Safety Rules
The safety warnings in this manual are important. By understanding the dangers inherent in the use of any firearm, and by taking the precautions described herein, you can experience complete safety in the use of your pistol. Failure to heed any of these warnings may result in serious injury to you or others, as well as severe damage to the firearm or other property.
PISTOLS are classified as FIREARMS and are sold by SIG SAUER with the specific understanding that we shall not be responsible in any manner whatsoever for malfunctioning of the firearm, physical injury or property damage resulting in whole or in part from:
• criminal or negligent discharge;
• improper or careless handling;
• unauthorized modifications; defective, improper, hand-loaded,
• or reloaded ammunition;
• corrosion;
• neglect; or
• other influences beyond our direct and immediate control.
This limitation applies regardless of whether liability is asserted on the basis of contract, negligence, or strict liability (including any failure to warn). Under no circumstance shall SIG SAUER, Inc. be liable for incidental or consequential damages, such as loss of use of property, commercial loss, and loss of earnings or profits.
1.1 Protect Your Eyes and Ears
Always wear safety glasses that meet the requirements of American National Standards Institute (ANSI) Z87.1 and ear plugs or “earmuff” type protectors whenever you are shooting. Always make certain that persons close to you are similarly protected. Unprotected eyes may be injured by powder, gas, carbon residue, lubricant, metallic particles, or similar debris that may emanate occasionally from any firearm in normal use. Without ear protection, repeated exposure to shooting noise may lead to cumulative, permanent hearing loss.
11
Page 12
2.0 Main Parts
38
13
56
1 - Barrel 4 - Slide 5 - Front Sight 6 - Rear Sight 13 - Frame
Note: Refer to section 13 for a detailed parts list and diagram.
19
17 - Slide Catch Lever 19 - Trigger 24 - Magazine Catch 29 - Hammer 38 - Decocking Lever
24 50
50 - Magazine Floor Plate 56 - SP2022 M Safety Lever, manual safety lock, left
6145
29
17
12
Page 13
2.1 SP2022 Technical Specifications
Caliber 9 mm .40 S&W .357 SIG
Length, overall
Height, overall
Width, overall
Barrel length
Rifling twist
No. of grooves
Sight radius
Weight incl. magazine
Magazine weight, empty
Trigger pull DA
Trigger pull SA
Magazine capacity/Rounds
*Specifications are subject to change without notice.
29.0 oz 30.4 oz 30.4 oz
15 12 12
7.40 in
5.70 in
1.40 in
3.90 in
6
5.90 in
10 lbs
4.4 lbs
13
Page 14
2.2 Mechanical Characteristics and Weapon Theory
2.3 Weapon Description
2.3.1 General
SIG SAUER pistols are modern handguns complying with the latest technical advances in weapon design for military, police and sporting use. They operate on the principle of the mechanically locked, recoil-operated pistol with semi-automatic reloading
2.3.2 Principal Features
The distinctive contrast sights in conjunction with the ergonomically favorable grip design permit rapid, precision target acquisition and firing.
Exchangeable grip plates of different sizes allow for an optimum adaptation of the weapon to the hand of the user.
The magazine catch can simply be repositioned from left-hand to right-hand operation.
A Picatinny rail is integrated into the frame such that tactical additional equipment can be attached.
The enclosed design prevents the penetration of dirt inside the weapon.
The SP 2022 pistol is available as double action/single action (DA/SA) or as double action only
14
Page 15
2.4 SP2022 M Manual Safety Model
W
WARNING – SAFETY
Uncontrolled discharge of shot May lead to death or severe injuries
• Never rely on safety mechanisms. They are never a substitute for careful and correct handling of the pistol.
• When the red dot is visible at the manual safety lock the pistol is ready to fire.
2.5 Manual Safety Lock
The manual safety lock works irrespective of whether the hammer is cocked or at rest. The function of the decocking lever is not affected by the position of the manual safety lock. The slide can also be operated (for loading or ejecting cartridges).
In DAO mode (hammer at rest) the enabled manual safety lock means that the hammer can be fully cocked (manually or by pulling the trigger).
In SA mode (hammer cocked) the enabled manual safety lock means that the hammer can be released by pulling the trigger.
15
Page 16
PISTOL LOCKED PISTOL READY TO FIRE
Enabling the manual safety lock:
1. Turn the safety lever 56 down up to the stop to lock the firing pin. The red dot is not visible. The pistol cannot be fired in this state. Disabling the manual safety lock:
2. Turn the safety lever 56 all the way up to unlock the firing pin. The red dot is visible. The pistol is ready to fire in this state.
2.6 Shock protection
The safety lock sits before the firing pin and prevents the firing pin from hitting the cartridge. Only after the trigger pulls the pulling rod does the safety lever push the safety lock upwards and thereby releases the firing pin.
16
Page 17
3.0 Ammunition
1. Use only high-quality, original, factory-manufactured ammunition. Do not use cartridges that are dirty, wet, corroded, bent, or damaged. Do not oil cartridges. Do not spray aerosol-type lubricants, preservatives, or cleaners directly onto cartridges or where excess spray may flow into contact with cartridges. Lubricant or other foreign matter on cartridges can cause potentially dangerous ammunition malfunctions. Only use ammunition of the caliber for which your firearm is chambered. The proper caliber is permanently engraved on your firearm; never attempt to use ammunition of any other caliber.
2. The use of reloaded, “remanufactured” hand-loaded, or other non-standard ammunition voids all warranties. Reloading is a science and improperly loaded ammunition can be extremely dangerous. Severe damage to the firearm and serious injury to the shooter or to others may result. Always use ammunition that complies with the industry performance standards established by the Sporting Arms and Ammunition Manufacturers’ Institute, Inc. (SAAMI) of the United States or ammunition manufactured to military specifications.
W
WARNING – AMMUNITION (CARTRIDGE) NOTICE
SIG SAUER SPECIFICALLY DISCLAIMS RESPONSIBILITY FOR ANY DAMAGE OR INJURY WHATSOEVER OCCURRING IN CONNECTION WITH, OR AS A RESULT OF, THE USE IN ANY SIG SAUER FIREARM OF FAULTY, NON-STANDARD, “REMANUFACTURED” HAND-LOADED (RELOADED) AMMUNITION, OR CARTRIDGES OTHER THAN THOSE FOR WHICH THE FIREARM WAS ORIGINALLY CHAMBERED.
17
Page 18
3. Firearms may be severely damaged and serious injury to the shooter or to others may result from any condition causing excessive pressure inside the chamber or barrel during firing. Excessive pressure can be caused by obstructions in the barrel, propellant powder overloads, the use of incorrect cartridges, or defectively assembled cartridges. In addition, the use of a dirty, corroded, or damaged cartridge can lead to a burst cartridge case and consequent damage to the firearm and personal injury from the sudden escape of high-pressure propellant gas within the firearm’s mechanism.
4. Immediately stop shooting and check the barrel for a possible obstruction whenever:
• You have difficulty in, or feel unusual resistance in, chambering a cartridge
• A cartridge misfires (does not go off)
• The mechanism fails to extract a fired cartridge case
• Unburned grains of propellant powder are discovered spilled in the mechanism
• A shot sounds weak or abnormal. In such cases it is possible that a bullet is lodged partway down the barrel. Firing a subsequent bullet into the obstructed barrel can wreck the firearm and cause serious injury to the shooter or to bystanders
5. Bullets can become lodged in the barrel:
• If the cartridge has been improperly loaded without propellant powder, or if the powder fails to ignite (ignition of the cartridge primer alone will push the bullet out of the cartridge case, but usually does not generate sufficient energy to expel the bullet completely from the barrel).
• If the bullet is not properly seated in the cartridge case. When such a cartridge is extracted from the chamber without being fired, the bullet may be left behind in the bore at the point where the rifling begins. Subsequent chambering of another cartridge may push the first bullet further into the bore.
18
Page 19
6. If there is any reason to suspect that a bullet is obstructing the barrel, immediately unload the firearm and look through the bore. It is not sufficient to merely look in the chamber.
A bullet may be lodged some distance down the barrel where it cannot easily be seen.
W
WARNING – LODGED BULLET
IF A BULLET IS IN THE BORE, DO NOT ATTEMPT TO SHOOT IT OUT BY USING ANOTHER CARTRIDGE OR BY BLOWING IT OUT WITH A BLANK OR ONE FROM WHICH THE BULLET HAS BEEN REMOVED. SUCH TECHNIQUES CAN GENERATE EXCESSIVE PRESSURE, DAMAGE THE FIREARM, AND CAUSE SERIOUS PERSONAL INJURY.
If the bullet can be removed with a cleaning rod, clean any unburned powder grains from the bore, chamber, and mechanism before resuming shooting. If the bullet cannot be dislodged by tapping it with a cleaning rod, send the firearm to SIG SAUER.
7. Dirt, corrosion, or other foreign matter on a cartridge can impede complete chambering and may cause the cartridge case to burst upon firing. The same is true of cartridges that are damaged or deformed.
8. Do not oil cartridges, and be sure to wipe the chamber clean of any oil or preservative before commencing to shoot. Oil interferes with the friction between cartridge case and chamber wall that is necessary for safe functioning, and subjects the firearm to stress similar to that imposed by excessive pressure.
9. Use lubricants sparingly on the moving parts of your firearm. Avoid excessive spraying of any aerosol gun care product, especially where it may get on ammunition. All lubricants and aerosol spray lubricants, in particular, can penetrate cartridge primers and cause misfires. Some highly penetrative lubricants can also migrate inside cartridge cases and cause deterioration of the propellant powder; on firing, the powder may not ignite. If only the primer ignites, there is danger that the bullet may become lodged in the barrel.
19
Page 20
W WARNING – AMMUNITION
Death, serious injury, and damage can result from the use of wrong ammunition, bore obstructions, powder overloads, or incorrect cartridge components. Always wear shooting glasses and hearing protectors.
IMPROPER AMMUNITION DESTROYS GUNS
W
WARNING – LEAD EXPOSURE
Discharging firearms in poorly ventilated areas, cleaning firearms, or handling ammunition may result in exposure to lead and other substances known to the state of California to cause birth defects, reproductive harm, and other serious physical injury. Maintain adequate ventilation at all times. Wash hands thoroughly after exposure.
SHOOTING OR CLEANING GUNS
MAY EXPOSE YOU TO LEAD
20
Page 21
4.0 Handling
4.1 Preparation Instructions
If you have the pistol and ammunition, and have read and understood all of the safety instructions, you are now ready to use the pistol.
4.2 Loading the Magazine
1. Ensure the magazine is the proper type and caliber for the pistol.
2. Press down on the magazine follower with the cartridge case rim. Ensure the bullet is facing the front of the magazine.
3. Push the cartridge to the rear and under the magazine lips.
4. Repeat until the magazine holds the desired number of cartridges.
Steps 2-3 Step 4
21
Page 22
4.3 Loading the Pistol (Ready to Fire)
1. Point the pistol in a safe direction.
2. Insert a full magazine and ensure it is engaged.
3. Pull the slide back fully and release, allowing the slide to fly forward.
Load state indicator
F
NOT LOADED LOADED
W
WARNING – LOADED PISTOL
THE PISTOL IS NOW LOADED AND READY TO FIRE.
22
Page 23
4.4 Reloading During Shooting
When the last round in the magazine is expended, the slide will be locked back in the open position by the slide catch lever.
1. Depress the magazine catch.
2. Remove the empty magazine.
Step 1
F
Step 2
F
23
Page 24
3. Insert a loaded magazine, making sure it is engaged.
4. Release the slide by: a. Pressing down on the slide catch lever or, b. Pulling back on the slide and release
Step 3 Step 4
F
F
F
W
WARNING – LOADED PISTOL
THE PISTOL IS NOW LOADED AND READY TO FIRE.
Always make sure the muzzle is pointed in a safe direction! Never attempt to load or unload any firearm inside a vehicle,building, or other confined space (except a properly constructed shooting range). Enclosed areas frequently offer no completely safe direction to point the firearm; if an accidental discharge occurs, there is great risk of bodily injury or property damage. Before loading, always clean all grease and oil from the bore and chamber, and check to be certain that no obstruction is in the barrel. Any foreign matter in the barrel could result in a bulged or burst barrel or other damage to the firearm, and could cause serious injury to the shooter or to others.
24
Page 25
5.0 Firing
W
WARNING – TRIGGER
DO NOT TOUCH THE TRIGGER UNTIL YOU ARE
ACTUALLY READY TO FIRE THE PISTOL.
Keep the muzzle pointed in a safe direction and your finger away from the trigger when cocking any firearm.
Never fire any firearm with your finger, hand, face, or other part of your body over or adjacent to the ejection port, or in any position where you may be struck by reciprocating movement of the breech. Both the ejection of empty cartridge cases and the movement of the breech are part of the normal operating cycle of firearms, and pose no safety hazard to the shooter if the firearm is held in a normal grip and fired at arm’s length.
Never allow other persons to stand beside you where they might be struck by an ejected cartridge case. The case is hot, and may be ejected with sufficient force to cause a burn, cut, or other injury. Wear safety glasses to protect eyes. Make certain there is a clear, unobstructed path for safe ejection of the fired case. Remember, the case may bounce off a hard object nearby and strike you or someone else.
W WARNING – MALFUNCTION
If, while shooting, your firearm develops a mechanical malfunction or binding, or “spits” powder/gas, or if a cartridge primer is punctured, or a cartridge case is bulged or ruptured, or if the report on firing does not sound quite right, STOP SHOOTING IMMEDIATELY! It may be dangerous to continue. UNLOAD THE FIREARM – DO NOT try “one more shot.” Take the firearm and the ammunition to a gunsmith for examination.
25
Page 26
5.1 Clearing a Jam
While shooting any firearm, an unfired cartridge or fired cartridge case may occasionally become jammed between the slide and the barrel. WHILE KEEPING THE MUZZLE POINTED IN A SAFE DIRECTION, clear the jam as follows:
1. Remove the magazine, then
2. Pull back the slide and lock it to the rear by pushing up the slide catch lever.
3. The jammed cartridge or case now can be removed by shaking it out or by picking it out.
W WARNING – HANDLING
The slide opens and shuts quickly while firing. Keep face and hands away from it. Hot brass and powder gas is ejected quickly and can burn you. Always wear safety glasses and hearing protectors.
SLIDE OPENS FAST – HOT BRASS EJECTED
W WARNING – DROPPED PISTOL
If dropped, the pistol may fire. Keep the cham­ber empty unless actually firing!
ANY GUN MAY FIRE IF DROPPED
26
Page 27
5.2 Firing the Pistol
1. Aim the pistol at a safe target
2. Place finger on the trigger and pull back to discharge.
Step 2
F
3. Keep pistol aimed at the target and continue to fire as required or until the pistol is empty.
5. Remove the magazine, unload and clear the pistol (see section 6.0 “Unload­ing the Pistol”). If the pistol is fired until the magazine is empty, the slide will remain locked to the rear. If firing is to continue, reload the pistol (see section 4.4 “Reloading During Shooting”).
27
Page 28
W WARNING – UNLOADING
Removing cartridges from the magazine does not prevent the pistol from being fired! When there is a cartridge in the chamber, the cartridge will discharge if the trigger is pulled. It is absolutely essential for the user to know how to completely unload the pistol. “Completely” means emptying the magazine and removing a chambered cartridge.
PISTOL WILL FIRE WITH MAGAZINE EMPTY OR REMOVED
28
Page 29
6.0 Unloading the Pistol
6.1 Unloading the Pistol (Magazine not Empty)
1. Keep the muzzle pointed in a safe direction.
2. Depress the magazine catch and remove the magazine.
3. Pull the slide back to the stop and engage the slide catch lever. The round is ejected and the slide is locked open.
4. Visually and manually check the chamber to ensure the pistol is completely free of ammunition.
5. Depress the slide catch lever, causing the slide to close.
6. Unload the magazine.
F
Step 2 Step 3
F
Step 4 Step 5
F
F
29
Page 30
6.2 Unloading the Pistol (Magazine Empty, Slide Open)
1. Keep the muzzle pointed in a safe direction.
2. Depress the magazine catch and remove the magazine.
3. Visually and manually check the chamber to ensure the pistol is completely free of ammunition.
4. Depress the slide catch lever, causing the slide to close.
Step 2 Step 3
F
F
Step 4
F
F
30
Page 31
Always make sure the muzzle is pointed in a safe direction! Remember to clear the chamber after the magazine has been removed.
Never assume that any gun is unloaded until you have personally checked it, visu­ally and physically!
After every shooting practice, make a final check to be certain the firearm is unloaded before leaving the range.
W
WARNING – UNLOADING
Removing cartridges from the magazine does not prevent the pistol from being fired! When there is a cartridge in the chamber, the cartridge will discharge if the trigger is pulled. It is absolutely es­sential for the user to know how to completely unload the pistol. “Completely” means emptying the magazine and removing a chambered cartridge.
PISTOL WILL FIRE WITH MAGAZINE EMPTY OR REMOVED
31
Page 32
7.0 Procedures in Case of Malfunction (“Jam”)
Follow the malfunction mitigation procedures if:
• You notice that a cartridge is difficult to chamber
• A cartridge does not go off
• The mechanism fails to extract a fired cartridge case
• You discover unburned grains of propellant powder spilled in the mechanism
• A shot sounds or feels weak or abnormal
W WARNING – JAM
LIVE ROUND JAM MAY NOT EJECT.
Firearms work reliably if properly maintained. If there is a malfunction during firing:
1. Keep the pistol pointed in a safe direction with your finger off the trigger.
2. Remove and secure the magazine.
3. Move the slide rearward and forward to clear any cartridge case in or near the chamber. Visually and manually inspect the chamber.
4. If you suspect that a bullet is lodged in the bore, field strip your pistol and check to see if the barrel is blocked. If there is a bullet lodged in the bore, return the pistol to SIG SAUER (see section 12.3 “Shipping Firearms for Repair”).
W WARNING – JAM
IF A BULLET IS IN THE BORE, DO NOT ATTEMPT TO SHOOT IT OUT BY USING ANOTHER CARTRIDGE, OR BY BLOWING IT OUT WITH A BLANK OR A CARTRIDGE FROM WHICH THE BULLET HAS BEEN REMOVED. THIS CAN GENERATE EXCESSIVE PRESSURE, DAMAGE THE FIREARM AND CAUSE SERIOUS PERSONAL INJURY OR DEATH.
32
Page 33
7.1 Troubleshooting Guide
Malfunction Cause Correction
Feed
No round fed into the chamber
Slide does not close easily or completely
Extraction/Ejection
After firing, the case stays in the chamber or is jammed in the ejection port
Ignition
Hammer drops but round does not fire
Magazine not properly inserted or magazine is deformed or dirty
Pistol or cartridge is fouled (dirty) or pistol is too heavily lubricated
Incorrect ammunition Replace ammunition
Pistol requires service Return to SIG SAUER
Insufficient recoil due to dirt
Light hold or limp wrist Solid grip, rigid hold
Low-powered ammunition
Pistol requires service Return to SIG SAUER
Firing pin obstructed Inspect, clean and
Faulty ammunition Manually cycle in
Pistol requires service Return to SIG SAUER
Insert magazine properly or change magazine
Clean and lubricate pistol and/or replace the ammunition
Clean and lubricate the pistol
Change ammunition
lubricate the pistol
next round
33
Page 34
W WARNING – JAMS
If your pistol stops firing with a live round in the chamber of a hot barrel (a misfire or jam), remove the round immediately. If you cannot remove the round within 10 seconds, remove the magazine and wait at least 15 minutes with the pistol pointing in a safe direction. This way, neither the user nor any other person would be injured by the possibility of a round “cooking-off” (a round detonating due to the heat of the barrel). Keep your face away from the ejection port while clearing a hot chamber.
7.2 Minimizing Malfunctions (“Jams”)
Malfunctions can largely be avoided by cleaning the pistol (see section 8.3 “Clean­ing the Pistol”).
• After each firing session
• Whenever a buildup of firing residue is suspected
• Whenever the pistol is exposed to extreme environmental conditions (rain, snow, freezing temperatures, etc.)
34
Page 35
8.0 Maintenance
W
WARNING – MAINTENANCE
Verify the magazine is removed – visually and physically confirm the pistol is unloaded before attempting disassembly or perform­ing any maintenance steps. Failure to ensure the firearm is unloaded could result in unintentional discharge, caus­ing injury or death.
VERIFY THE FIREARM IS UNLOADED
8.1 Pistol Disassembly
1. Unload the pistol ( see section 6.0 “ Unloading the Pistol”)
2. Retract the slide to stop and lock open by engaging the slide catch lever.
3. Verify visually that there is not a round in the chamber.
4. Retract the slide and allow the slide to move forward slightly allowing the disassembly notch to align with the tab on the slide catch lever.
5. Push out and remove the slide catch lever and allow the slide to move forward in a controlled fashion.
6. Move the complete slide assembly (slide, barrel, recoil spring and guide) forward off the frame.
35
Page 36
W WARNING
Slide is under spring tension. Maintain positive control during slide removal to prevent damage or injury. Wear eye protection.
6. Move the complete slide assembly (slide, barrel, recoil spring and guide) forward and off the frame.
Step 2 Step 3 Step 4
F
F
Step 5 Step 6
36
F
Page 37
W WARNING
The recoil spring and guide are under spring tension and not firmly attached to the slide. Use caution to prevent injury or damage to the pistol. Wear eye protection.
7. Push the recoil spring guide forward slightly and lift from rear to remove the recoil spring and guide from the slide.
8. Remove the barrel from the slide by pulling upward slightly and to the rear. This level of disassembly is sufficient to allow a thorough cleaning after shooting.
Step 7
Step 8
u
37
Page 38
8.2 Magazine Disassembly
1. Locate the bottom of the magazine floorplate.
2. Using a punch, cleaning rod, or similar tool, depress the magazine insert and push the magazine floorplate forward until it is clear of the magazine tube.
W WARNING
The magazine spring is compressed. Guard the magazine insert and magazine spring with your thumb to control the release of magazine spring tension. Uncon­trolled release can cause injury. Wear eye protection.
3. Remove the magazine follower and magazine spring from the magazine tube. This level of disassembly is sufficient to allow a thorough cleaning after shooting.
Step 1 Step 2 Step 3
38
Page 39
8.3 Cleaning the Pistol
W
WARNING
Never clean the barrel from the muzzle end; do not use a steel wire brush as it can damage the smooth surface of the barrel. Use a suitable cleaning rod and a brush of the correct caliber.
Solvents can be harmful to the surface finish of the pistol. Read and follow the manufacturer’s warnings before using solvents or cleaners. Wear eye protection.
AVOID OVER-LUBRICATION OF COMPONENTS.
1. Lubricate the cleaning brush with gun oil and insert it into the barrel via the chamber (opposite the muzzle end).
2. Wipe powder residues and oil from the barrel bore and chamber with clean­ing patches.
3. Clean exterior surfaces of the barrel with a brush coated with gun oil.
4. Remove dirt from guides of the frame, inside and outside of slide, recoil spring guide and recoil spring with a brush or cleaning patch. Lightly lubricate same surfaces with a cloth impregnated with gun oil or gun grease.
5. Lightly oil bores of the barrel and chamber. Remove any excess lubricant.
CAUTION: Avoid over
lubrication of components.
Slide
Barrel
Recoil Spring
Frame Hammer
Grip Module
Takedown Lever
Trigger
Recoil Guide
39
Page 40
8.4 Pistol Assembly
1. Verify the pistol is clear of all foreign matter.
2. Place the barrel into the slide.
W WARNING
The recoil spring and guide are under spring tension and not firmly attached to the slide. Use caution to prevent injury or damage to the pistol. Wear eye protection.
3. Insert recoil spring guide assembly into the slide.
Step 2
Step 3
40
u
Page 41
4. Guide the slide onto the frame rails from the front.
5. Insert the slide catch lever in until is stops on the slide.
6. Retract the slide until the tab on the slide catch lever aligns with take down notch on the slide.
7. Push the slide catch lever in the remaining distance and allow the slide to move forward in a controlled fashion.
8. Press the decocking lever down. (not applicable on DAO pistols)
Step 4 Step 5
F
Step 6 Step 7
F
F
Step 8
41
Page 42
8.5 Magazine Assembly
1. Orient the magazine follower on the magazine spring and insert into the bottom of the magazine tube.
W WARNING
The magazine spring is being compressed during assembly. Guard the magazine insert and magazine spring with your thumb to control magazine spring tension. Uncontrolled release can cause injury. Wear eye protection.
2. Insert the magazine spring fully into the magazine tube until the magazine insert is flush with the magazine tube bottom.
3. Holding the magazine insert in place, slide the magazine floorplate onto the magazine tube lips until the magazine floorplate is locked in place by the maga­zine insert.
Step 2 Step 3
42
Page 43
8.6 Function Verification
The function check is performed on the assembled pistol to verify functionality. It should be performed after the completion of repairs and after each cleaning and assembly of the pistol.
W WARNING – MAINTENANCE
Verify the magazine is removed – visually and physically confirm the pistol is unloaded before attempting disassembly or performing any maintenance steps. Failure to ensure the firearm is unloaded could result in unintentional discharge, causing injury or death.
VERIFY THE FIREARM IS UNLOADED
43
Page 44
1. Ensure the magazine is removed and the pistol is unloaded (see section 6.0 “Unloading the Pistol”).
2. Check recoil spring function/slide travel. a. Retract the slide fully and release. b. Verify the slide locks fully in the closed position. c. Repeat the procedure.
3. Check the trigger mechanism: a. Pull the trigger fully to the rear. b. As the trigger is pulled rearward, verify the hammer cocks. At the end of trigger travel, the hammer should fall forward firmly.
Step 2a
Step 3a - 3b
44
F
F
F
Page 45
4. Check slide catch lever. a. Insert an empty magazine. b. Retract the slide fully and release. c. Verify the slide is locked to the rear by the slide catch lever. d. Depress the slide catch lever. e. Verify the slide is released and closes in the locked position. f. Remove the magazine.
Step 4a, 4b & 4c Step 4d & 4e Step 4f
F
F
F
F
Step 5d
5. Inspect the magazine. a. Check the condition of the magazine tube. b. Verify the magazine floorplate is secure. c. Check for free movement of the magazine follower and spring. d. Insert the magazine into the pistol and remove. Verify smooth insertion. Check the magazine catch for clean engagement and smooth release.
F
F
F
45
Page 46
6. Inspect the pistol exterior. a. Inspect the general condition of the pistol. b. Check the sights, body, slide, and takedown lever for damage. c. Verify the front and rear sights are secure.
W WARNING – INSPECTION
Never use a firearm or magazine that shows signs of damage or fails a function check. Verify the magazine is the correct model and caliber for the pistol. If the condition or function of the pistol or magazine is suspect, return the pistol or magazine to SIG SAUER for evaluation.
VERIFY THE CONDITION AND FUNCTION
46
Page 47
9.0 Pistol Adjustments
9.1 General Information
The P250 pistol is designed for both right-hand and left-hand operation and a variety of hand sizes. The slide catch lever can be operated from either side. The magazine catch may be repositioned to either side based on shooter preference. The grip module may be replaced by the shooter, providing a range of ergonomically correct grip configurations.
W WARNING – UNLOADING
Verify the magazine is removed and visually and physically confirm the pistol and chamber are unloaded before attempting disassembly or performing any maintenance steps. Failure to ensure the firearm is unloaded could result in unintentional discharge, causing injury or death.
VERIFY THE FIREARM IS UNLOADED
47
Page 48
9.2 Magazine Catch Removal and Reversal
1. Depress the magazine catch until the back protrudes slightly from the opposite side and hold.
2. On the protruding side, press the straightened end of a paper clip into the hole on the back side of the magazine catch to release the magazine catch stop.
3. Remove the magazine catch stop.
4. Remove the magazine catch and magazine catch spring, keeping the two pieces together.
5. Insert the magazine catch and magazine catch spring on the desired side of the pistol body.
6. Insert the magazine catch stop from the opposite side until the magazine catch stop latch engages.
Step 2 Steps 3 & 4
Steps 5 & 6
F
48
u
Page 49
W WARNING – DISASSEMBLY
Do not attempt to disassemble your pistol beyond the point explained in this manual. Further disassembly should only be done at the factory. Some of the components require special skills, tools and fixtures for disassembly.
DO NOT DISASSEMBLE BEYOND INSTRUCTIONS
49
Page 50
W WARNING – ALTERATIONS
This product was designed to function properly in its original condition. Altera­tions can make it unsafe. Do not alter any part or add or substitute any parts or accessories not manufactured by SIG SAUER for this pistol.
DO NOT ALTER ANY GUN
50
Page 51
10.0 Sights
10.1 General Information
The SP2022® pistol is equipped with high contrast or SIGLITE™ Night Sights. The front sight is drift adjustable for windage. Both the front and rear sights are available in different heights, which allows for elevation adjustments.
W WARNING – SIGHT ADJUSTMENT
Sight corrections should only be performed by someone with the necessary knowledge – the pistol could become damaged.
10.2 Windage (Left/Right) Adjustment
Adjust the point of impact left or right by moving the front sight in its dovetail. Move the front sight in the direction of the impact – if the rounds impact left of target, move the front sight left to correct. If the rounds impact right of target, move the front sight right to correct. Moving the sight 0.02” changes the point of impact approximately 3” at 25 yards.
Note: SIG SAUER has a Sight Adjustment Tool available that makes it easier to adjust and change sights.
Impact left of point of aim Impact low of point of aim
51
Page 52
W WARNING – SIGHT ADJUSTMENT
Sight corrections should ONLY be performed on an unloaded firearm. Manipulating the sights on a loaded firearm could result in unintentional discharge, causing injury or death. Visually and physically confirm the pistol is unloaded before making sight adjustments.
DO NOT ADJUST THE SIGHTS ON A LOADED FIREARM
52
Page 53
11.0 Transportation and Storage
When transporting your firearm to and from shooting activities, keep it unloaded for your safety and for the safety of others. When storing your firearm, keep it separated from ammunition, under lock and key if possible, and out of the reach of children and other inexperienced or unauthorized persons.
W WARNING – STORAGE
Never place or store any firearm in such a manner that it may be dislodged. Firearms should always be stored securely and unloaded, away from children and other unauthorized users. Use the locking device originally supplied with this firearm for storage. The use of a locking device or safety lock is only one aspect of responsible firearms storage. For increased safety, firearms should be stored unloaded and locked in a location that is both separate from their ammunition and inaccessible to children and any other unauthorized person.
STORE SECURELY AND UNLOADED
53
Page 54
12.0 Service and Parts Policy
12.1 Parts Policy
Our Service Department maintains a full complement of replacement parts. Even though most gunsmiths have the knowledge, training, and the ability to make necessary repairs to your firearm, the skill and workmanship of any particular gunsmith is totally beyond our control.
Should your firearm ever require service, we strongly recommend that you return it to SIG SAUER (see section 12.3 “Shipping Firearms for Repair”). A firearm is a precision instrument and some replacement parts will require individual fitting to ensure correct operation. A wrong part, improper fitting, or incorrect mechanical adjustment may result in an unsafe condition or dangerous malfunction, damage to the firearm, or cause possible serious injury to the shooter or others.
IF ANY PART IS ORDERED WITHOUT RETURNING THE FIREARM TO SIG SAUER, the customer bears full responsibility for ensuring that the part supplied is correct for their particular firearm and is properly installed and fitted by a qualified gunsmith.
SIG SAUER CANNOT BE RESPONSIBLE FOR THE FUNCTIONING OF ANY FIREARM IN WHICH REPLACEMENT PARTS ARE INSTALLED BY OTHERS.
W WARNING – PARTS PURCHASERS
It is the purchaser’s responsibility to be absolutely certain that any parts ordered from the factory are correctly fitted and installed. Firearms are complicated mechanisms and IMPROPER FITTING OF PARTS MAY RESULT IN A DANGEROUS MALFUNCTION, DAMAGE TO THE FIREARM, AND SERIOUS
and installer of parts must accept full responsibility for the correct adjustment and functioning of the firearm after such installation.
INJURY TO THE SHOOTER AND OTHER PERSONS. The purchaser
PARTS MUST FIT CORRECTLY
54
Page 55
12.2 Service Policy
If you have questions concerning the performance or servicing of your firearm, please write or call:
SIG SAUER, Inc.
Attention: Customer Service
18 Industrial Drive, Exeter, NH 03833
Phone: (603) 610-3000 ext. 3
Fax: (603) 766-7002
IF YOU DO NOT UNDERSTAND THE INSTRUCTIONS FOR OPERATING YOUR PISTOL, IT IS YOUR RESPONSIBILITY TO CALL OUR CUSTOMER SERVICE DEPARTMENT AT (603) 610-3000 EXT. 3 BEFORE USING YOUR FIREARM.
12.3 Shipping Firearms for Repair
In the event you need to return your firearm to the SIG SAUER Service Depart­ment, here’s what to do:
1. First contact Customer Service at (603) 610-3000 ext. 3 for an RMA number, which will allow SIG SAUER to track the status of your return from its receipt at SIG SAUER through its return to you. Please do not send your firearm until you obtain an RMA number.
2. Make sure that the chamber and magazine(s) are unloaded and that no am­munition is included with your returned firearm.
3. Package the firearm securely to prevent damage. Enclose a letter that includes your name, street address, daytime phone number, model and serial number, and a detailed description of the problem you have experienced or the work you want performed. With the exception of extra magazines, do not include any other
55
Page 56
accessories such as scopes or mounts.
4. Generally, an individual may ship firearms to the manufacturer for repair or service. Some states and localities, however, prohibit this. If you live in such an area, the firearms must be shipped by and returned to a federally licensed firearms dealer.
5. Federal law prohibits persons who do not possess a Federal Firearms License from shipping a firearm via the U.S. Postal Service. (Note: any shipment of fire­arms outside U.S. borders is subject to the export laws of the United States and to the valid laws of the specific country, which you must strictly follow; prior to exporting any firearm you should seek legal counsel.)
6. SIG SAUER is not responsible for any firearm until it is received, nor for damage incurred during shipment.
7. Ship your firearms insured and prepaid (we do not accept collect shipments) to:
SIG SAUER, Inc.
Attention: Service Department
18 Industrial Drive Exeter, NH 03833
Don’t forget to write your RMA number on the package.
A copy of this instruction manual should always accompany this pistol and be transferred with it upon change of ownership.
56
Page 57
12.4 Ordering Parts
In the event you want to order parts for your firearm, contact Customer Service at (603) 610-300 ext. 3
Have available the serial number of your firearm and the part diagram number for the part(s) you wish to order. A parts list and diagram of the pistol is provided in section 13.0.
Please refer to the Service and Parts Policy.
W WARNING – SHIPPING
Before shipping any firearm, be absolutely certain that the firearm and its magazines are unloaded.
DO NOT ship ammunition with a firearm. Failure to follow this warning could result in uninten­tional discharge, causing injury or death.
VERIFY THE FIREARM
IS UNLOADED
57
Page 58
13.0 Parts List
ITEM / DESCRIPTION
1 BARREL 2 RECOIL SPRING GUIDE 3 RECOIL SPRING 4 SLIDE 5 FRONT SIGHT 6 REAR SIGHT 7 FIRING PIN POSITIONING PIN 8 SAFETY LOCK SPRING 9 SAFETY LOCK 10 EXTRACTOR 10A EXTRACTOR PIN 10B EXTRACTOR SPRING 11 FIRING PIN SPRING 12 FIRING PIN 13 FRAME 14 LOCKING INSERT 15 AXIAL LOCKING SPRING 16 LOCKING INSERT PIN 17 SLIDE CATCH LEVER 18 SLIDE CATCH LEVER SPRING 19 TRIGGER 20 TRIGGER SPRING 21 TRIGGER PIVOT PIN 22 TRIGGER BAR 23 MAGAZINE CATCH SPRING 24 MAGAZINE CATCH 25 MAGAZINE CATCH STOP 26 HAMMERBOX 27 DRIVE LEVER 28 HAMMER RESET SPRING 29 HAMMER
30 SAFETY LEVER 31 HAMMER PIVOT PIN 32 HAMMER STRUT 33 MAINSPRING 34 HAMMER STRUT BUSHING 35 HAMMER STRUT PIN 36 SEAR 37 SEAR SPRING 38 DECOCKING LEVER 39 SEAR PIVOT PIN 40 DECOCKING LEVER SPRING 41 TRIGGER BAR PUSHER SPRING 42 TRIGGER BAR PUSHER 43 UPPER HAMMER BOX PIN 44 LOWER HAMMER BOX PIN 45 GRIP 46 MAGAZINE TUBE 47 MAGAZINE INSERT 48 MAGAZINE SPRING 49 MAGAZINE FOLLOWER 50 MAGAZINE FLOORPLATE 51 LOADED CHAMBER INDICATOR SPRING 52 LOADED CHAMBER INDICATOR 53 LOADED CHAMBER INDICATOR PIN 54 TRIGGER PIVOT PIN RETAINER
SP2022 M ONLY:
55 MANUAL SAFETY LEVER RETAINING PIN 56 MANUAL SAFETY LEVER 57 MANUAL SAFETY LEVER ASSEMBLY 58 MANUAL SAFETY STOP SPRING 59 MANUAL SAFETY DETENT BALL
58
Page 59
14.0 Parts Diagram
59
Page 60
SIG SAUER® Limited Lifetime Firearms Warranty
SIG SAUER® warrants that the enclosed firearm was originally manufactured free of defects in material, workmanship and mechanical function. For the lifetime of the original purchaser, SIG SAUER agrees to correct any defect in the firearm for the original purchaser by repair, adjustment or replacement, at SIG SAUER’s option, with the same or comparable quality components (or by replacing the firearms at SIG SAUER’s option); provided, however, that the firearm is returned unloaded and freight prepaid to:
SIG SAUER
18 Industrial Drive
Exeter, NH 03833
This limited warranty is null and void if the firearm has been misused, damaged (by accident or otherwise), fired with handloaded, reloaded or improper ammunition, fired with an obstruction in the barrel, damaged through failure to provide reasonable and necessary maintenance as described in the manual accompanying the firearm, or if unauthorized repair or any alteration, including of a cosmetic nature, has been performed on the firearm. This limited warranty does not apply to normal wear and tear of any parts. Subject to the foregoing, this limited warranty confers the right to have the covered firearm or its parts repaired, adjusted or replaced exclusively upon the original purchaser, which right is not transferable to any other person. No implied warranties of any kind are made herein and this warranty does not apply to any accessory items attached or appurtenant to the firearm. In no event shall SIG SAUER be liable for any incidental or consequential damages arising from or in connection with this limited warranty.
60
Page 61
Notes:
61
Page 62
Notes:
62
Page 63
Notes:
63
Page 64
FOR PRODUCT SERVICE ON THIS MODEL,
PLEASE CALL (603) 610-3000 EXT. 3
72 Pease Boulevard, Newington, NH 03801 USA
P/N 1600097 REV 01
www.sigsauer.com
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use