SIGLENT SPD3000 Series User Manual
User Manual
SPD3000 Series
Programmable DC Power Supply
SIGLENT TECHNOLOGIES CO., LTD
www.biall.com.pl
SIGLENT
SPD3000 User Manual I
Copyright information
1. SIGLENT TECHNOLOGIES CO., LTD. All Rights Reserved.
2. Information in this publication replaces all previous corresponding material.
3. SIGLENT reserves the right to change the specifications and price of the
product.
4. Any way of copying, extracting and translating the content of the manual is
not allowed without permission of SIGLENT.
Note:
SIGLENT is the registered trademark of SIGLENT TECHNOLOGIES CO., LTD.
www.biall.com.pl
SIGLENT
II SPD3000 User Manual
General Safety Summary
Please review the following safety precautions carefully to avoid personal
injury or damage to this product or any product connected to it. To prevent
potential danger, please use the instrument as specified.
Use proper power cord
Only the power cord designed for the instrument and authorized by local
country could be used.
Power supply
AC Input Voltages: 100V/110V/220V/230V ±10%, 50/60Hz.
Use proper fuse
The fuse types: 100V/110V: T6.3A/250V; 220V/230V: T3.15A/250V;
Make sure to use the correct type of fuse before turning on the instrument.
Do not connect the power cord before replacing the fuse.
Find out the reason why the fuse burned out before replacing the fuse.
Ground the instrument
The instrument is grounded through the protective terra conductor of the power
cord. To avoid electric shock, the grounding conductor must be connected to
the earth. Make sure that the instrument is properly grounded before any
inputs or outputs.
Observe all terminal ratings
To avoid fire or electric shock, please observe all ratings and symbols on the
instrument. Read this guide carefully to know more details about the ratings
before connection.
Keep proper ventilation
Inadequate ventilation may cause an increase of temperature,, which will lead
to further damage. Please keep proper ventilation and check the fan and
air-vents regularly when using the instrument.
Operate condition
Location: indoor, no strong light, almost no Interfering pollution;
Comparative humidity: <80%
Altitude: <2000m
Temperature: 0℃ to 40℃
www.biall.com.pl
SIGLENT
SPD3000 User Manual III
Do not operate in an explosive atmosphere
To avoid personal injury or damage to instrument, please do not operate in an
explosive atmosphere.
Keep surface of the product clean and dry
To avoid dust or moisture in the air influence the performance of the
instrument , please keep surface of the product clean and dry.
www.biall.com.pl
SIGLENT
IV SPD3000 User Manual
Safety Terms and Symbols
Terms may appear on the product:
DANGER: Indicates direct injury or hazard that may happen.
WARNING: Indicates potential injury or hazard that may happen.
CAUTION: Indicates potential damage to the instrument or other property that
may happen.
Symbols may appear on the product:
Hazardous Protective Warning Earth Power
Vlotage Earth Ground Ground Switch
www.biall.com.pl
SIGLENT
SPD3000 User Manual V
SPD3000 Series Brief Introduction
SPD3000 series Programmable DC Power Supply is convenient, flexible and
multi-function. It has three independent outputs, two sets of adjustable voltage
value and a fixed set of selectable voltage value of 2.5V, 3.3V, and 5V ,and it
also provides output short circuit and overload protection at the same time.
Main features of SPD3000 Series
4.3” TFT color LCD display with content of 16M;
Three independent outputs, two of which are adjustable, and the total power
up to 195W;
Four kinds of input voltage values includes 100V, 110V, 220V and 230V to
satisfy different requirements;
Function of storage and call setting parameters;
Function of timing output ;
Function of waveform display, Real-time display of voltage or current
waveforms with digital display of voltage, current and power values
Start up screen protective procedure every fixed interval(30 minutes)
Perfect PC software to realize the real-time control through USBTMC..
www.biall.com.pl
SIGLENT
VI SPD3000 User Manual
Content
General Safety Summary ....................................................................................................II
SPD3000 Series Brief Introduction..................................................................................... V
Chapter 1 Start Guide..........................................................................................................1
The front panel..........................................................................................................................2
The rear panel ...........................................................................................................................6
Notice in first use of SPD3000 Series.................................................................................7
Input power requirement ...........................................................................................................7
Electrical check.........................................................................................................................7
Output check .............................................................................................................................8
Chapter 2 Control panel operation ......................................................................................9
2.1 Output summary ............................................................................................................10
2.2 CH1/CH2 Independent Output.....................................................................................11
2.3 CH3 Independent mode................................................................................................12
2.4 CH1/CH2 Series mode .................................................................................................13
2.5 CH1/CH2 Parallel mode ...............................................................................................15
2.7 Timer................................................................................................................................17
2.9 Version information........................................................................................................20
2.10 Upgrade firmware........................................................................................................21
Chapter 3 Remote control .................................................................................................23
3.1 Command list..................................................................................................................23
3.2 Command description...................................................................................................24
Chapter 4 Specification......................................................................................................30
Chapter 5 Troubleshooting ................................................................................................32
Chapter 6 Service and Support .........................................................................................33
Maintain summary................................................................................................................33
Contact SIGLENT.................................................................................................................33
Appendix A: Accessories ........................................................................................................34
www.biall.com.pl
SIGLENT
SPD3000 User Manual 1
Chapter 1 Start Guide
In this chapter, we mainly introduce the panel and Display Interface of
SPD3000, and also the notes about how to check and operate it at the first use.
You can quickly understand how to operate it after reading the following steps.
Please check the instrument according to the following steps.
1. The machine and packing inspection
If the packing or cushioning material is seriously damaged, please retained
them for follow-up inspection.
If the instrument is damaged during shipment, the compensation will be
provided by consigner or carrier, and SIGLENT will not undertake free repair
or replacement.
If there is a mechanical damage or loss please contact with your sales
representative.
2.Accessory examination
Information about the accessories is introduced in detail at the end of the
manual, you can refer to this description to check whether the accessories are
completed t.
If there are accessories damaged or lacked, please contact with your
SIGLENT sales representative.
www.biall.com.pl
SIGLENT
2 SPD3000 User Manual
The front panel
NO. Description NO. Description
1 Logo 9 CH3 DIP Switch
2 Display Area 10 Power Switch
3 Model 11 CH1 Output Terminal
4
System parameter
configuration button
12 Ground Terminal
5 Multi-function knob 13 CH2 Output Terminal
6 Fine Adjust button 14 CV/CC indicator light
7 Right/Left Direction button 15 CH3 Output Terminal
8 Channel Control button
○
6
○
7
○
8
○
9
○
10 ○11 ○12 ○13 ○14 ○15
○
1 ○2 ○3 ○4 ○5
www.biall.com.pl
SIGLENT
SPD3000 User Manual 3
Instruction for buttons
Buttons for setting parameters
: Press the button to turn on/off the waveform display interface;
: Press the button to set series mode of CH1/CH2, and the logo
“ ” displays at the same time;
:Press the butten to set parallel mode of CH1/CH2, and the logo
“ ” displays at the same time;
:Press the butten to enter the storage function interface
:Press the butten to enter timer setting interface
: Press the button longer to lock it and shorter to turn to system
information interface.
Buttons for controlling the channel
: Press the button to turn on/off all the channels;
: Press the button to select CH1 as the current channel;
: Press the button to select CH2 as the current channel;
: Press the button to turn on/off the CH1 output;
: Press the button to turn on/off the CH3 output.
Other buttons
: Press the button to open the fine tuning function and change the
parameters with the minimum step;
: To move the cursor around.
WAVEDISP
SER
PARA
LOCK/VER
TIMER
RECALL/SAVE
CH3 ON/OFF
CH2
CH1
ALL ON/OFF
ON/OFF
FINE
www.biall.com.pl
SIGLENT
4 SPD3000 User Manual
The output terminal on front panel
The output terminals of CH1、CH2 and CH3 include positive terminal and
negative terminal, and a common ground for CH1 and CH2 additional. Each
channel has its own logo. The operation details are introduced in the
follow-up ” control panel operation”.
www.biall.com.pl
SIGLENT
SPD3000 User Manual 5
User interface
○
1 Parallel/Series logo: The logo will be displayed when the corresponding
mode is on
○
2 Channel logo;
○
3 Operating mode logo: The corresponding logo will display when working in
CV or CC mode;
○
4 LOCK logo: It will display when the LOCK is turned on
○
5 USB logo: It will display when there is a USB connection;
○
6 Voltage value;
○
7 Current value;
○
8 Power value;
○
9 Timer lD: Timer state identification
○
10 Channel on/off logo;
○
10
○
6
○
7
○
8
○
1 ○2 ○3 ○4 ○5
○9
www.biall.com.pl
SIGLENT
6 SPD3000 User Manual
The rear panel
Description:
○
1 warning message
○
2 The DIP switch of the AC power and its identification .
○
3 The description of the AC input voltage
○
4 AC power socket
○
5 The fan air vents
○
6 CE certification mark
○
7 USB interface and identification
○
1 ○2
○6 ○5 ○4 ○3
○
7
www.biall.com.pl
Loading...