SIGLENT SPD1305X, SPD1168X, SPD1000X Series Quick Start Manual

SIGLENT

Quick Start

SPD1000X Programmable Linear DC

Power Supply

QS0501X-E02B

2018 SIGLENT TECHNOLOGIES CO.，LTD

SIGLENT

Copyright and Declaration

Copyright

SIGLENT TECHNOLOGIES CO.，LTD. All Right Reserved.

Trademark Information
SIGLENT is a registered trademark of SIGLENT TECHNOLOGIES.

Declaration

 SIGLENT products are protected by patent law in and outside of the
Peoples Republic of China

.
 SIGLENT reserved the right to modify or change the specifications and
price of the product

 Information in this publication replace all previous corresponding material

 Any copying, extracting or translation of the content of this manual is not

allowed without permission from SIGLENT.

SPD1000X Quick Start I

SIGLENT

General Safety Summary

Please review the following safety precautions carefully to avoid personal
injury or damage to this product or any product connected to it. To prevent
potential danger, please use the instrument as specified.

Use the proper power cord

Only the power cord designed for the instrument and authorized by the local
country should be used.

Power supply

AC Input Voltages: 100/120/220/230 V ± 10%，50/60 Hz

Use the proper fuse

The fuse type: 100/120 V: T6.3A/250V
220/230 V : T3.15A/250V

Make sure to use the correct type of fuse before turning on the instrument.
Find the cause of the fuse failure before replacing the fuse and connecting
the power cord.

Ground the instrument

The instrument is grounded through the protective earth conductor of the
power cord. To avoid electric shock, the grounding conductor must be
connected to the earth ground. Make sure that the instrument is properly
grounded before any activating any inputs or outputs.

Examine all the terminal ratings

To avoid fire or electric shock, please examine all ratings and symbols on the
instrument. Read this guide carefully to know more details about the ratings
before connection.

Keep proper ventilation
Inadequate ventilation may cause an increase of temperature within the

II SPD1000X Quick Start

SIGLENT

instrument, which can lead to further damage. Please keep proper ventilation
and check the fan and air-vents regularly when using the instrument.

Operate condition

Location: indoor, no strong light, almost no interfering pollution
Relative humidity: < 80%
Altitude：< 2000 m
Temperature: 0℃ to 40℃

Electrostatic Prevention

Operate in an electrostatic discharge protective area environment to avoid
damages induced by static discharges. Always ground both the internal and
external conductors of the cable to release static before connecting.

Do not operate in an explosive atmosphere

To avoid personal injury or damage to instrument, please do not operate in an
explosive atmosphere.

Keep surface of the product clean and dry

Avoid dust and moisture in the air as they can influence the performance of
the instrument. Please keep surface of the product clean and dry.

SPD1000X Quick Start III

SIGLENT

Hazardous
Power

Protective
Earth
Terminal

Warning

Earth
Ground

Power
Switch

General Safety Summary

Terms may appear on the product:

DANGER: Indicates direct injury or hazard that may happen.

WARNING: Indicates potential injury or hazard that may happen.

CAUTION: Indicates potential damage to the instrument or other property

that may happen.

Symbols may appear on the product:

Hazardous

IV SPD1000X Quick Start

SIGLENT

SPD1000X Brief Introduction

Siglent’s SPD1000X Programmable DC Power Supply has a 2.8 inch
TFT-LCD screen, programmable output, and real time measurement
graphing. The SPD1168X has a maximum output values of 16 V/8 A, while
the SPD1305X has a maximum output values of 30 V/5 A. Both models have
remote sense capability, output short circuit and overload protection.

Figure 1: Side view

Main features:

 Single high-precision programmable output:

SPD1168X：16 V/8 A, total power is 128 W
SPD1305X：30 V/5 A, total power is 150 W

 Compact, easy to use, powerful, ideal for bench power supply applications

 Stable, Reliable and Low Noise: ≤ 350 uVrms/3 mVpp

SPD1000X Quick Start V

SIGLENT

 Fast Transient Response Time: < 50μs

 Maximum resolution of 1mV/ 1mA with 5-bit voltage and 4-bit current

display.

 Timer function sequences pre-set output values

 High resolution 2.8 inch TFT LCD(240*320 pixels)

 Two output modes: two-wire output and remote sense compensation

function (maximum compensation up to 1V)

 Four varieties of input-line voltage values include 100V, 110V, 220V and

230V to satisfy user requirements

 Intelligent temperature-controlled fan, effectively reduces noise

 Clear graphical interface, with waveform display

 5 internal system parameters save / recall, support for data storage space

expansion

 Uses EasyPower PC software, real-time control via USB, LAN, support

SCPI command set and LabView driver package to meet the remote
control and communication requirements

VI SPD1000X Quick Start