SIGLENT SDL1000X, SDL1020X, SDL1000X-E, SDL1030X, SDL1020X-E Quick Start Manual

SDL1000X

Programmable DC

Electronic Load

Quick Start

Copyright

and

Statement

Copyright

SIGLENT TECHNOLOGIES CO., LTD. All rights reserved.

Trademark Information

SIGLENT is registered trademark of SIGLENT TECHNOLOGIES CO., LTD.

Statement

SIGLENT products are protected by patent laws in and outside of the P.R. China.

SIGLENT reserves the rights to change the specication and price.

Information in this publication replaces all previous corresponding published material.

Contents in this manual are not allowed to be copied, extracted or translated in any form or by any means without SIGLENT’s permission.

SDL1000X Quick Start-I

General

Safety

Summary

Please review the following safety precautions carefully to avoid personal
injury or damage to this product or any product connected to it. To prevent

potential danger, please use the instrument as specied.

Use proper power cord

Only the power cord designed for the instrument and authorized by local
country could be used.

Power supply

AC Input Voltages: 110V/220V ±10%, 50/60Hz.

Use proper fuse

- The fuse types: 110V/220V: T315mA/250V.

- Make sure to use the correct type of fuse before turning on the instrument.

- Do not connect the power cord before replacing the fuse.

- Investigate the reason why the fuse burned out before replacing the fuse.

Ground the instrument

The instrument is grounded through the protective ground conductor of
the power cord. To avoid electric shock, the grounding conductor must
be connected to the earth. Make certain that the instrument is properly
grounded.

II-SDL1000X Quick Start

Observe all terminal ratings

To avoid re or electric shock, please observe all ratings and symbols on the

instrument. Read this guide carefully to learn more details about the ratings
before connection.

Keep proper ventilation

Inadequate ventilation may cause an increase of temperature, which will
lead to further damage. Please keep proper ventilation and check the fan
and air-vents regularly when using the instrument.

Operate condition

Location: indoor, no strong light, almost no Interfering pollution, Comparative
humidity: <80%, Altitude: <2000m, Temperature: 0℃ to 40

Electrostatic Prevention

Operate in an electrostatic discharge protective area environment to avoid
damages induced by static discharges. Always ground both the internal and
external conductors of the cable to release static before connecting.

Do not operate in an explosive atmosphere

To avoid personal injury or damage to instrument, please do not operate in
an explosive atmosphere.

Keep surface of the product clean and dry

To avoid dust or moisture in the air influence the performance of the
instrument, please keep surface of the product clean and dry.

℃

Safety

Terms and

Symbols

Terms may appear on the product:

DANGER: Indicates direct injury or hazard that may happen.

WARNING: Indicates potential injury or hazard that may happen.

CAUTION: Indicates potential damage to the instrument or other property

that may happen.

Symbols may appear on the product:

Hazardous

Voltage

Protective

Earth Ground

Warning

Earth

Ground

Power

Switch

SDL1000X Quick Start-III

SDL1000X
Brief
Introduction

SDL1000X/SDL1000X-E series Programmable DC Electronic Load has a 3.5

inch TFT-LCD display, and comes with a simple, user-friendly interface and

superb performance specications. The SDL1020X/ SDL1020X-E comes with

an input range of 150 V/30 A @ 200 W. The SDL1030X/ SDL1030X-E comes

with an input range of 150 V/30 A @ 300 W. The SDL1000X series leads

with measurement resolution of 0.1mV/0.1mA and the base SDL1000X-E

series resolution is 1mV/1mA. Adjustable current slew rate range is 0.001

A/μs~2.5 A/μs, and it comes with built-in RS232/USB/LAN communication

interfaces. Standard SCPI communication protocol is used to establish an

intelligent testing platform for applications in various industries, such as the

power industry, battery industry, LED lighting, automotive electronics, and

aerospace.

Main features of SDL1000X

• SDL1020X (Single channel): DC 150 V/30 A, total power up to 200 W

• SDL1030X (Single channel): DC 150 V/30 A, total power up to 300 W

• 4 Static modes / Dynamic mode: CC/CV/CR/CP

• CC Dynamic modes, continuous, pulsed, toggled

• CC Dynamic mode: 25 KHz, CP Dynamic mode: 12.5 KHz, CV Dynamic
mode: 0.5 Hz

IV-SDL1000X Quick Start

• Adjustable current slew rate range 0.001 A/us~2.5 A/us

• Min read-back resolution: 0.1 mV, 0.1 mA

• Measuring speed of voltage and current: up to 500 KHz

• List can edit one hundred steps; Program support programing fty group

data

• Over current protection test, Over power protection test, Battery test,

short circuit and CR-LED test functions

• 4-wire SENSE compensation mode function

• External voltage and current control function

• Voltage, Current monitoring via 0-10V

• 3.5 inch TFT-LCD display, capable of displaying multiple parameters and
states simultaneously

• With memory function in case of power-down

• OCP, OVP, OPP, OTP and LRV protection

• Graphical display of waveformFunction of Restore libraryFunction of test
the rise and fall time base on the voltage Von and Vlatch functions

• Smart fan control

• Remote control and measurements via PC