Sierra Wireless HL8529 User Manual

Product Technical Specification
AirPrime HL8518, HL8528 and HL8529
4117047
2.2
December 18, 2015
Product Technical Specification
Important Notice
Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices such as the Sierra Wireless modem are used in a normal manner with a well-constructed network, the Sierra Wireless modem should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using the Sierra Wireless modem, or for failure of the Sierra Wireless modem to transmit or receive such data.
Safety and Hazards
Do not operate the Sierra Wireless modem in areas where cellular modems are not advised without proper device certifications. These areas include environments where cellular radio can interfere such as explosive atmospheres, medical equipment, or any other equipment which may be susceptible to any form of radio interference. The Sierra Wireless modem can transmit signals that could interfere with this equipment. Do not operate the Sierra Wireless modem in any aircraft, whether the aircraft is on the ground or in flight. In aircraft, the Sierra Wireless modem MUST BE POWERED OFF. When operating, the Sierra Wireless modem can transmit signals that could interfere with various onboard systems.
Note: Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door
The driver or operator of any vehicle should not operate the Sierra Wireless modem while in control of a vehicle. Doing so will detract from the driver or operator’s control and operation of that vehicle. In some states and provinces, operating such communications devices while in control of a vehicle is an offence.
is open. Sierra Wireless modems may be used at this time.
Limitations of Liability
This manual is provided “as is”. Sierra Wireless makes no warranties of any kind, either expressed or implied, including any implied warranties of merchantability, fitness for a particular purpose, or noninfringement. The recipient of the manual shall endorse all risks arising from its use.
The information in this manual is subject to change without notice and does not represent a commitment on the part of Sierra Wireless. SIERRA WIRELESS AND ITS AFFILIATES SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR REVENUE ARISING OUT OF THE USE OR INABILITY TO USE ANY SIERRA WIRELESS PRODUCT, EVEN IF SIERRA WIRELESS AND/OR ITS AFFILIATES HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THEY ARE FORESEEABLE OR FOR CLAIMS BY ANY THIRD PARTY.
Notwithstanding the foregoing, in no event shall Sierra Wireless and/or its affiliates aggregate liability arising under or in connection with the Sierra Wireless product, regardless of the number of events, occurrences, or claims giving rise to liability, be in excess of the price paid by the purchaser for the Sierra Wireless product.
Customer understands that Sierra Wireless is not providing cellular or GPS (including A-GPS) services. These services are provided by a third party and should be purchased directly by the Customer.
Product Technical Specification
SPECIFIC DISCLAIMERS OF LIABILITY: CUSTOMER RECOGNIZES AND ACKNOWLEDGES SIERRA WIRELESS IS NOT RESPONSIBLE FOR AND SHALL NOT BE HELD LIABLE FOR ANY DEFECT OR DEFICIENCY OF ANY KIND OF CELLULAR OR GPS (INCLUDING A-GPS) SERVICES.
Patents
This product may contain technology developed by or for Sierra Wireless Inc.
®
This product includes technology licensed from QUALCOMM
This product is manufactured or sold by Sierra Wireless Inc. or its affiliates under one or more patents licensed from InterDigital Group and MMP Portfolio Licensing.
.
Copyright
© 2015 Sierra Wireless. All rights reserved.
Trademarks
Sierra Wireless®, AirPrime®, AirLink®, AirVantage®, WISMO®, ALEOS® and the Sierra Wireless and Open AT logos are registered trademarks of Sierra Wireless, Inc. or one of its subsidiaries.
Watcher
Windows
Macintosh countries.
QUALCOMM
Other trademarks are the property of their respective owners.
®
is a registered trademark of NETGEAR, Inc., used under license.
®
and Windows Vista® are registered trademarks of Microsoft Corporation.
®
and Mac OS X® are registered trademarks of Apple Inc., registered in the U.S. and other
®
is a registered trademark of QUALCOMM Incorporated. Used under license.
Contact Information
Phone: 1-604-232-1488
Sales Desk:
Post:
Technical Support:
RMA Support:
Web:
Hours: 8:00 AM to 5:00 PM Pacific Time
Contact:
Sierra Wireless 13811 Wireless Way Richmond, BC Canada V6V 3A4
support@sierrawireless.com
repairs@sierrawireless.com
Fax: 1-604-231-1109
http://www.sierrawireless.com/
http://www.sierrawireless.com/sales
Consult our website for up-to-date product descriptions, documentation, application notes, firmware upgrades, troubleshooting tips, and press releases: www.sierrawireless.com
Product Technical Specification
Document History
Version Date Updates
1.0 May 20, 2015 Creation
Updated:
1 Introduction  Error! Reference source not found. Error! Reference source
not found.
1.1 May 29, 2015
2.0 December 02, 2015
2.1 December 10, 2015 Updated Table 8 Current Consumption (at nominal voltage, 3.7V)
2.2 December 18, 2015 Updated Chapter 7 Regulatory Legal Information
Error! Reference source not found. Error! Reference source
not found.
Error! Reference source not found. Error! Reference source
not found.
Deleted 4.1 Model Views
Added Error! Reference source not found. Error! Reference source not found.
Updated:
Table 1 Supported Bands/Connectivity  1.2 Physical Dimensions  Table 2 General Features  Table 3 ESD Specifications  1.9 Environmental and Certifications  Error! Reference source not found. Error! Reference source
not found.
Table 5 Power Supply  2.4 Current DC Power Consumption  Error! Reference source not found. Error! Reference source
not found.
Error! Reference source not found. Error! Reference source
not found.
Error! Reference source not found. Error! Reference source
not found.
Error! Reference source not found. Error! Reference source Error! Reference source not found. Error! Reference source
not found.
Deleted HSIC
Contents
1.INTRODUCTION .................................................................................................... 9
1.1. Common Flexible Form Factor (CF3) ............................................................................... 9
1.2. Physical Dimensions ..................................................................................................... 10
1.3. General Features .......................................................................................................... 10
1.4. Encryption Support ........................................................................................................ 13
1.5. Architecture ................................................................................................................... 13
1.6. Interfaces ...................................................................................................................... 14
1.7. Connection Interface ..................................................................................................... 14
1.8. ESD .............................................................................................................................. 15
1.9. Environmental and Certifications ................................................................................... 15
1.9.1. Environmental Specifications ................................................................................. 15
1.9.2. Regulatory ............................................................................................................. 16
1.9.3. RoHS Directive Compliant ..................................................................................... 16
1.9.4. Disposing of the Product ........................................................................................ 16
1.10. References .................................................................................................................... 16
2.DETAILED INTERFACE SPECIFICATIONS ....................................................... 17
2.1. Power Supply ................................................................................................................ 17
2.1.1. Electrical Characteristics ........................................................................................ 17
2.1.2. Pin Description ....................................................................................................... 17
2.1.3. Burst Transmission Current Requirements ............................................................ 18
2.1.4. Power Input (VBATT) ............................................................................................. 19
2.2. Ground Connection ....................................................................................................... 19
2.3. Decoupling of Power Supply Signals ............................................................................. 19
2.4. Current DC Power Consumption ................................................................................... 20
2.5. VGPIO ........................................................................................................................... 22
2.5.1. Electrical Characteristics ........................................................................................ 22
2.5.2. Pin Description ....................................................................................................... 22
2.6. BAT_RTC ...................................................................................................................... 2 2
2.6.1. Electrical Characteristics ........................................................................................ 23
2.6.2. Pin Description ....................................................................................................... 23
2.7. SIM Interface ................................................................................................................. 23
2.7.1. Electrical Characteristics ........................................................................................ 24
2.7.2. Pin Description ....................................................................................................... 24
2.7.3. UIM1_DET ............................................................................................................. 25
2.7.4. Application ............................................................................................................. 25
2.8. USB .............................................................................................................................. 26
2.8.1. Electrical Characteristics ........................................................................................ 26
2.8.2. Pin Description ....................................................................................................... 26
2.9. Electrical Information I/O ............................................................................................... 26
Product Technical Specification
2.10. General Purpose Input/Output (GPIO) .......................................................................... 27
2.11. Main Serial Link (UART1) .............................................................................................. 28
2.11.1.Pin Description ....................................................................................................... 28
2.11.2.8-wire Application ................................................................................................... 29
2.11.3.4-wire Application ................................................................................................... 29
2.11.4.2-wire Application ................................................................................................... 29
2.12. POWER ON Signal (PWR_ON_N) ................................................................................ 30
2.13. Reset Signal (RESET_IN_N) ........................................................................................ 30
3.DESIGN GUIDELINES ......................................................................................... 32
3.1. Power-Up Sequence ..................................................................................................... 32
3.2. Module Switch-Off ......................................................................................................... 32
3.3. Emergency Power OFF ................................................................................................. 33
3.4. Sleep Mode Management ............................................................................................. 33
3.4.1. Using UART ........................................................................................................... 33
3.4.2. Using USB ............................................................................................................. 33
3.5. Power Supply Design .................................................................................................... 34
3.6. ESD Guidelines for SIM Card ........................................................................................ 34
3.7. ESD Guidelines for USB ............................................................................................... 35
3.8. Dual SIM Application ..................................................................................................... 35
3.9. Radio Frequency Integration ......................................................................................... 36
4.REGULATORY LEGAL INFORMATION ............................................................. 37
4.1. Label ............................................................................................................................. 37
4.2. FCC Regulations ........................................................................................................... 37
4.3. RF Exposure Information .............................................................................................. 38
4.4. IC Regulations ............................................................................................................... 38
4.5. CE Warning ................................................................................................................... 3 9
5.TERMS AND ABBREVIATIONS .......................................................................... 40
List of Figures
Figure 1. Architecture Overview ................................................................................................... 13
Figure 2. Mechanical Overview .................................................................................................... 14
Figure 3. Power Supply During Burst Transmission ..................................................................... 18
Figure 4. Power Supply Requirements ......................................................................................... 19
Figure 5. Power Supply Voltage Drops Shapes During Burst Transmission ................................. 20
Figure 6. UIM1 Application Reference Schematic ........................................................................ 25
Figure 7. 8-wire UART Application Example ................................................................................ 29
Figure 8. 4-wire UART Application Example ................................................................................ 29
Figure 9. 2-wire UART Application Example ................................................................................ 29
Figure 10. PWR_ON_N Assertion Time ......................................................................................... 30
Figure 11. PWR_ON_N Sequence with VGPIO Information .......................................................... 32
Figure 12. PWR_ON_N Sequence with T
Figure 13. Power OFF Sequence for PWR_ON_N, VGPIO ........................................................... 33
Figure 14. Voltage Limiter Example ............................................................................................... 34
Figure 15. EMC and ESD Components Close to the SIM .............................................................. 34
Figure 16. ESD Protection for USB ................................................................................................ 35
Figure 17. Reference Design for Dual SIM Application .................................................................. 35
Figure 18. GSM Antenna Connection with Antenna Detection ....................................................... 36
.............................................................................. 32
rampup
List of Tables
Table 1. Supported Bands/Connectivity ........................................................................................ 9
Table 2. General Features .......................................................................................................... 10
Table 3. ESD Specifications ........................................................................................................ 15
Table 4. Environmental Specifications ........................................................................................ 15
Table 5. Power Supply ................................................................................................................ 17
Table 6. Power Supply Pin Description ....................................................................................... 17
Table 7. Radio Burst Rates – Connected Mode .......................................................................... 18
Table 8. Current Consumption (at nominal voltage, 3.7V) ........................................................... 20
Table 9. Current Consumption per Power Supply (VBATT_PA and VBATT) .............................. 21
Table 10. VGPIO Electrical Characteristics ................................................................................... 22
Table 11. VGPIO Pin Description .................................................................................................. 22
Table 12. BAT_RTC Electrical Characteristics .............................................................................. 23
Table 13. BAT_RTC Pin Description ............................................................................................. 23
Table 14. Electrical Characteristics of UIM1.................................................................................. 24
Table 15. UIM1 Pin Description .................................................................................................... 24
Table 16. USIM Socket Pin Description ........................................................................................ 25
Table 17. Electrical Characteristics of USB ................................................................................... 26
Table 18. USB Pin Description ...................................................................................................... 26
Table 19. Digital I/O Electrical Characteristics .............................................................................. 26
Table 20. GPIO Pin Description .................................................................................................... 27
Table 21. UART1 Pin Description ................................................................................................. 28
Table 22. PWR_ON_N Electrical Characteristics .......................................................................... 30
Table 23. RESET_IN_N Electrical Characteristics ........................................................................ 31
Table 24. AirPrime HL852x FCC IDs ............................................................................................ 37
Table 25. AirPrime HL852x IC ...................................................................................................... 39
1. Introduction
This document is the Product Technical Specification for the AirPrime HL8518, HL8528 and HL8529 Embedded Modules. It defines high level features and illustrates the interfaces for these features. This document is intended to cover hardware aspects, including electrical and mechanical, of the AirPrime HL8518, HL8528 and HL8529.
The AirPrime HL8518, HL8528 and HL8529 modules belong to the AirPrime HL Series from the Essential Connectivity Module family. These are industrial grade Embedded Wireless Modules that provide voice and data connectivity on GPRS, EDGE RX, WCDMA, HSDPA and HSUPA networks (as listed in Table 1 Supported Bands/Connectivity).
The HL8518, HL8528 and HL8529 modules support a large variety of interfaces such as Digital Audio, GPIOs and UART to provide customers with the highest level of flexibility in implementing high-end solutions.
Table 1. Supported Bands/Connectivity
RF Band
UMTS B1 1922 to1978 MHz 2112 to 2168 MHz
UMTS B2 1852 to 1908 MHz 1932 to 1988 MHz
UMTS B5 826 to 847 MHz 871 to 892 MHz
UMTS B8 882 to 913 MHz 927 to 958 MHz
GSM 850 824 to 849 MHz 869 to 894 MHz
E-GSM 900 880 to 915 MHz 925 to 960 MHz
DCS 1800 1710 to 1785 MHz 1805 to 1880 MHz
PCS 1900 1850 to 1910 MHz 1930 to 1990 MHz
Transmit band (Tx)
Receive band (Rx)
HL8518
HL8528
HL8529
1.1. Common Flexible Form Factor (CF3)
The AirPrime HL8518, HL8528 and HL8529 belong to the Common Flexible Form Factor (CF3) family of modules. This family consists of a series of WWAN modules that share the same mechanical dimensions (same width and length with varying thicknesses) and footprint. The CF provides a unique solution to a series of problems faced commonly in the WWAN module space as it:
Accommodates multiple radio technologies (from 2G to LTE advanced) and band groupings
Supports bit-pipe (Essential Module Series) and value add (Smart Module Series) solutions
Offers electrical and functional compatibility
Provides Direct Mount as well Socketability depending on customer needs
3
form factor
Product Technical Specification Introduction
1.2. Physical Dimensions
The AirPrime HL8518, HL8528 and HL8529 modules are compact, robust, fully shielded modules with the following dimensions:
Length: 23 mm
Width: 22 mm
Thickness: 2.5 mm
Weight: 2.65 g
Note: Dimensions specified above are typical values.
1.3. General Features
The table below summarizes the AirPrime HL8518, HL8528 and HL8529 features.
Table 2. General Features
Feature Description
Small form factor (146-pin solderable LGA pad) – 23mm x 22mm x 2.5mm
(nominal)
Physical
Electrical Single or double supply voltage (VBATT and VBATT_PA) – 3.2V – 4.5V
RF
Audio interface
Metal shield can
RF connection pad
Baseband signals connection
HL8518 (dual-band UMTS and dual-band GSM):
UMTS B1
UMTS B8
E-GSM 900
DCS 1800
HL8528 (dual-band UMTS and dual-band GSM):
UMTS B2
UMTS B5
GSM 850
PCS 1900
HL8529 (dual-band UMTS):
UMTS B2
UMTS B5
Digital interface (ONLY)
Supports Enhanced Full Rate (EFR), Full Rate (FR), Half Rate (HR), and
both Narrow-Band and Wide-band Adaptive Multirate (AMR-NB and AMR­WB) vocoders
MO and MT calling
Echo cancellation and noise reduction
Emergency calls (112, 110, 911, etc.)
Incoming call notification
DTMF generation
4117047 Rev 2.2 December 18, 2015 10
Product Technical Specification Introduction
Feature Description
Dual SIM Single Standby (DSSS) with fast network switching capability
1.8V/3V support
SIM interface
Application interface
Protocol Stack
SIM extraction / hot plug detection
SIM/USIM support
Conforms with ETSI UICC Specifications.
Supports SIM application tool kit with proactive SIM commands
NDIS NIC interface support (Windows XP, Windows 7, Windows 8, Windows
CE, Linux)
Multiple non-multiplexed USB channel support
Dial-up networking
USB selective suspend to maximize power savings
CMUX multiplexing over UART
AT command interface – 3GPP 27.007 standard, plus proprietary extended
AT commands
Dual-mode UMTS (WCDMA) / HSDPA / HSUPA / EDGE RX / GPRS / GSM operation
GSM/GPRS/EDGE RX
GPRS Class 12 EDGE RX CSD (Circuit-switched data bearers) Release 4 GERAN Feature Package 1 SAIC / DARP Phase 1 Latency Reduction Repeated FACCH and Repeated SACCH GPRS ROHC Enhanced Operator Name String (EONS) Enhanced Network Selection (ENS)
WCDMA
3GPP WCDMA FDD Multimode Type II UE Protocol Stack Configurable for data classes up to 384 kBit/s Inter-RAT Handover and Cell Reselection Supports two types of Compressed Mode Network Assisted Cell Change from UTRAN to GERAN and GERAN to
UTRAN
CSD (Circuit-switched data bearers) over WCDMA (transparent/non
transparent up to 64 kBit/s; Support for Video Telephony)
HSDPA (High Speed Downlink Packet Access)
Compliant with 3GPP Release 5 HSDPA Category 8 data rate – 7.2 Mbps (peak rate) IPv6 support
HSUPA (High Speed Uplink Packet Access)
Compliant with 3GPP Release 6 HSUPA Category 6 data rate - 5.76 Mbps (peak rate) Robust Header Compression (RoHC)
Fractional DPCH
4117047 Rev 2.2 December 18, 2015 11
Product Technical Specification Introduction
Feature Description
HSPA+ (Evolved High Speed Packet Access)
Compliant with 3GPP Release 7 Higher-Order Modulation (HOM)
Protocol Stack
SMS
Supplementary Services
Connectivity
Operating temperature ranges (industrial grade):
Environmental
MAC-ehs support Continuous Packet Connectivity (CPC) Enhanced F-DPCH Enhanced Cell FACH Circuit Switched Voice over HSPA
SMS MO and MT
CS and PS support
SMS saving to SIM card or ME storage
SMS reading from SIM card or ME storage
SMS sorting
SMS concatenation
SMS Status Report
SMS replacement support
SMS storing rules (support of AT+CNMI, AT+CNMA)
Call Barring
Call Forwarding
Call Hold
Caller ID
Call Waiting
Multi-party service
USSD
Automatic answer
Multiple (up to 20) cellular packet data profiles
Sleep mode for minimum idle power draw
Automatic GPRS attach at power-up
GPRS detach
Mobile-originated PDP context activation / deactivation
Support QoS profile
Release 97 – Precedence Class, Reliability Class, Delay Class, Peak
Throughput, Mean Throughput
Release 99 QoS negotiation – Background, Interactive, and Streaming
Static and Dynamic IP address. The network may assign a fixed IP address
or dynamically assign one using DHCP (Dynamic Host Configuration Protocol).
Supports PAP and CHAP authentication protocols
PDP context type (IPv4, IPv6, IPv4v6). IP Packet Data Protocol context
RFC1144 TCP/IP header compression
Interaction with existing GSM services (MO/MT SMS voice calls) while:
GPRS is attached, or  In a GPRS data session (class B GPRS suspend / resume procedures)
Class A: -30°C to +70°C
Class B: -40°C to +85°C
4117047 Rev 2.2 December 18, 2015 12
Product Technical Specification Introduction
Feature Description
RTC Real Time Clock (RTC) with calendar and alarm
Temperature Sensor
Temperature monitoring
Alarms
1.4. Encryption Support
The AirPrime HL8518, HL8528 and HL8529 supports the following encryption algorithms:
Ciphering algorithms A51, A52 and A53
GEA1/GEA2 and GEA3 algorithm for GPRS encryption
Cyclic Redundancy Check (CRC) with programmable polynomial
UMTS confidentiality algorithm f8 for message ciphering (Kasumi based UEA1)
UMTS integrity algorithm f9 for message authentication (Kasumi based UIA1 and SNOW 3G
based UIA2)
1.5. Architecture
The figure below presents an overview of the AirPrime HL8518, HL8528 and HL8529 modules internal architecture and external interfaces.
AirPrime HL8518, HL8528 and HL8529
26MHz
VBATT
GND
VGPIO BAT_RTC GPIO x 12
ADC x2
UART1 (8pins)
Debug (2pins)
JTAG
2
6
M
_
C
K
L
O
32K_CLKOUT
SIM1
RESET_IN_N
TP1
PWR_ON_N
PWM x 2
2G_TX_ON
USB
PCM
SAW
Filters
TX_2G
_
3
G
B2-PCS/B5-
Transceiver
3G PA
RX_DCS
RX_2G RX_3G
T
X
Baseband
MCU DSP
U
T
PMU RF
Analog Baseband
Peripherals
Isoplexer
B1/B8-
GSM900
Or
GSM850
Or
B2/B5
RX_DCS
RF
2G PA
+
Antenna
Switch
RF
RF
Memory
(Flash + RAM)
32.768KHz
Figure 1. Architecture Overview
4117047 Rev 2.2 December 18, 2015 13
Loading...
+ 28 hidden pages