Sierra Monitor Corporation Catalytic Bead 5100-02-IT, Catalytic Bead IT Series, Sentry IT 5100-02-IT Specification Sheet

Proven Performance - FM Approved
Cost effective - 180 day Calibration frequency , maintenance cut in half!
The 5100-02-IT Combustible Gas Sensor Module is a key member of the powerful Sierra Monitor IT Series family of gas sensor modules. The 5100-02-IT provides the features needed by safety and instrumentation en­gineers including:
180 day calibration interval
FM Approval for performance and safety
SIL-2 certified
Modbus RTU RS-485 interface
4-20 mA output
HART Interface
SMC Sentry digital bus interface
Optional Integral 8 AMP alarm relays – Alarm,
Warning
Aluminum or 316 Stainless Steel enclosure
Non-intrusive calibration
Integral scrolling LED display
Optional remote sensor
Remote alarm reset capable
Model 5100-02-IT utilizes the proven, reliable, catalytic bead technology to monitor for combustible gases (meth­ane and others). Output range is 0-100% of Lower Explo­sive Limit (LEL). This detector has minimal maintenance requirements and is Factory Mutual approved for six month calibration intervals. Internal, continuous self-diagnostics automatically detect and alarm any fault problems. The 5100-02-IT can be used as a 4-20 mA component or as a Modbus RTU node. For higher level system capability the module can interface directly to Sierra Monitor’s Sentry Controller enabling system level Modbus serial communi­cations, area and zone alarm management, extensive system diagnostic features, WebServer interface, and multiplexing sensor connections.
Sentry IT Gas Sensor Module
IT Combustible - Catalytic Bead
180 Day Calibration Interval
Factory Mutual (FM) Approval for performance, electri­cal safety and environmental parameters including Class I, Div . 1, Groups B, C, D and Class I, Zone 1, Group IIC, IP66. With a NEMA-4X enclosure standard, approved multiplexing, and approved six month calibration inter­val, cost of ownership is minimized at the acquisition, installation and operating stages.
How It Works
Catalytic Bead gas sensors detect gas by comparing the resistance of two heated elements. One element is catalytic to enhance the burning of combustible gases, the other element is passive. Electronic circuits are used to compare the change in the catalytic bead resistance relative to the passive bead. The relative change is calibrated to determine the concentration of the gas of interest.
Features
Six-month calibration interval
Non-intrusive calibrationNetwork-compatible with Modbus, 4-20 mA,
Sentry bus, HART and relay interface
FM Approved for Performance and Hazardous
Areas
SIL-2 CertifiedLocal scrolling display
Sierra Monitor Corporation 1991 Tarob Ct. Milpitas, CA 95035 USA (408) 262-6611 (800) 727-4377 Fax: (408) 262-9042
Visit our website: www.sierramonitor.com E-mail: sales@sierramonitor.com
Benefits
Longest rated and FM-approved calibration cycle for any catalytic-bead gas detector - reduced mainte­nance
Able to calibrate module without declassifying the area Easily meets users needs for access to critical plant
safety information Proven and approved for installation in areas where
combustible gases are located Meets long term reliability design standards Ease of calibration and easy access to gas concentra-
tion, relay and alarm status and diagnostics
S
O
O
C
C
)
Specifications:
IT Combustible Gas Sensor - Catalytic Bead
:epytrosne
daeBcitylataC :ataDlacirtcelE
:ecnamrofreP :noitpmusnocrewoP.xamsttaw3
:egnaRLEL%001-0:epytnoitcennoCeriw3
ilibataepeRLEL%1-/+:egatlovtupnICDV03-01:lanimonCDV42
:yt
:emitesnopseRelacslluf%06otces21<:noitcetorPIME/IFR2-2
:qerfnoitarbilaCsyad081 :egnaRgnitarepO
:ycaruccAegnarLEL%05-0rof%1-/+:egnaRpmeTtneibmA04-
egnarLEL%001-15rof%2-/+:ytidimuHevitaleR%99-0
:tuptu
:noitcurtsnoC
:yalpsiDDELgnillorcSdnadexiF:snoisnemiD)mc21x31x81(.ni8.4x0.5x2.7)lA(
:tuptuOlangiSsublatigidyrtneS:thgieW)gK5.2(bl2.5)SS(--)gK3.1(.bl7.2)lA(
anA:gnisuoHromunimuladetaocyxopE
,)Am5.2,elbuorT(Am02-4gol
)Am5.1(noitarbilaC leetSsselniatS613
)Am5.2elbuorT(,)Am5.1aerAsuodrazaH
subdoM584-SRlaireS
UTR
:noitacifissalC,1.viD,IssalC,foorpnoisolpxE
:yaleRelbuorT.pmA52.0 ,1enoZ,IssalCD,C,Bspu
:snoitp
:syaleR,TDPS,)gninraw,mrala(pma8 04-=6TCIIdxE,DG2II
CDV03@A5,CAV052@A8:ytnarraWsraey2
snoitcennocyrailixuasedulcnidraoB :slavorppA
:TRAH,TRAHsedulcnidraobnoitanimreT
gnixelpitlumyrtneSrof0236dr
latigiD,Am02-4,584-SRsubdoM
uByrtneSoN,tuptuoyaleRA2,tupnI
s
adnatSMFecnamrofreProtceteDsaGelbitsubmoC
0063dradnatSMF
deifitreC2-LIS
ASC
Specifications subject to change without notice
8005NE,2-18005NE
o
o
o
671ot
x5.7)SS(
o
04-(F
08ot
)C
)mc11x31x91(.ni4.4x0.5
orG
X4AMEN,56PI,66PI,CIIpuorG
o
o
58otC
C
D,C,BspuorG,1.viD,IssalC
)80516CEI(retsigeRs'dyolLybdeifitreC
snoitacolsuodrazahnierusolcneroF
Ordering Information
Relay/ Remote
Model Enclosure Connection Protection Option
5100-02-IT -XX -XX -XX -X -X
- A1 = AL 3/4” NPT - 01 = No Relays (std.) - 00 = Std. - 0 = Std. - 0 = None
- A2 = AL M20 x 1.5 - 02 = Relays Option - 1 = Remote
- S1 = SS 3/4” NPT - 05 = HART Option Sensor
- S2 = SS M20 x 1.5
10-8535dradnatS,daeHnoitarbilaC00-1135dleihsniaR 00-0635gnittiFyrevileDsaGnoitarbilaC20-1135tropn
srotarbila
yticapaChgiH
10-0521AepyT,tiKnoitarbilaCrosneSsaG 20-0621AepyTrednilyCsaGLEL%05saGelbitsubmoC 24-0621AepyT, 00-0621
seirosseccAnoitarbila
Sierra Monitor Corporation 1991 Tarob Ct. Milpitas, CA 95035 USA (408) 262-6611 (800) 727-4377 Fax: (408) 262-9042
Visit our website: www.sierramonitor.com E-mail: sales@sierramonitor.com
Remote Sensor Option
It is often necessary to sample the combustible gas at some distance from the gas sensor module. The IT Series enables the user to mount the sensor remotely from the transmitter without the need for expensive and high-main­tenance sample pumps. The Remote Sensor Option pro­vides a separate gas sensor that can be mounted up to 50 feet from the transmitter and connected via a cable in­cluded.
seirosseccA
oitarbilachtiwdleihsniaR
rednilyCsaG,LEL%05,negordyH
elbaliavatonriatneibmaorezyrotcafsitasfi(AepyT,rednilyCsaG,)riA(saGoreZ
Rev. 10/11
Loading...