We have checked the contents of this manual for agreement with the hardware
and software described. Since deviations cannot be precluded entirely, we cannot
guarantee full agreement. However, the data in this manual are reviewed regularly
and any necessary corrections included in subsequent editions. Suggestions for
improvement are welcomed.
Technical data subject to change.
Copyright E Siemens AG 2000 Ć 2003 All Rights Reserved
The reproduction, transmission or use of this document or its contents is not
permitted without express written authority. Offenders will be liable for damages.
All rights, including rights created by patent grant or registration of a utility model or
design, are reserved.
Where ’adapter’ is referred to below, the text applies to both
variants.
The PC adapter connects a PC to the MPI/DP interface
(Multipoint Interface) via the serial COM port of an S7/M7/C7
system.
This does not require a PC slot, that is, the adapter is also
suitable for use in non-expandable PCs such as notebooks.
1)PC adapter19.2/38.4 kbps
PC
RS232
COM 1 ...
1)RS232 cable 6ES7 901-1BF00-0XA0, length 6m
RS232 Switch
19.2/38.4 kbps
Figure 1-1PC Adapter in the System
PC/TS Adapter
A5E00078070-02
MPI/DP
S7/M7/C7
system
1
PC/TS AdapterQuick Reference Guide
With ’direct connection’, the TS adapter allows you to link
programming devices/PCs with S7/M7/C7 systems. With this
setup, the TS adapter corresponds in functionality to the PC
adapter.
With ’modem connection’, the TS adapter enables you to link
programming devices/PCs with S7/M7/C7 systems over the
telephone network.
Direct Connection
1)
PC
RS232
COM1...
Modem Connection
PG/PC
1)RS232 cable 6ES7 901-1BF00-0XA0, length 6m
2)Modem cable (supplied with modem)
RS232
COM1...
2)
RS232
Modem
Telephone network
Modem
RS232
19.2/38.4 kb
2)
TS adapterRS232
Switch
19.2/38.4 kbps
TS adapterRS232
MPI/DP
MPI/DP
S7/M7/C7
system
S7/M7/C7
system
Figure 1-2TS Adapter in the System
The TeleService optional package is always required to
operate the TS adapter (see 5.2 Software). The switch on the
adapter is used to change the transmission rate on the
RS232 side in direct connection. With modem connection, it
has no function.
PC/TS Adapter
2
A5E00078070-02
PC/TS AdapterQuick Reference Guide
Adapter
MPI/DP connector
RS232 connector
LED “POWER”
LED “ACTIVE”
Switch
“19.2/38.4 kbps”
Figure 1-3Adapter
The two adapter types differ with respect to the location of the
MPI/DP parameters:
S The MPI/DP parameters for the PC adapter are set in
“Set PG/PC interface”. When opening an online display
for the first time, ther parameters are transferred to the PC
adapter.
S The MPI/DP parameters for the TS adapter are set via a
Teleservice application and stored permanently on the TS
adapter. When opening an online display for the first time,
these parameters are activated.
PC/TS Adapter
A5E00078070-02
3
PC/TS AdapterQuick Reference Guide
2Package Components
S Adapter
S Quick Reference Guide
S Mounting assembly (TS adapter only)
3Accessories (not part of the adapter package)
S RS232 cable, 6 meters in length 6ES7 901-1BF00-0XA0
(required to operate the PC adapter and to operate the
TS adapter in direct connection only).
4MPI/DP Network
A maximum of 32 nodes can be interfaced to an MPI/DP
network segment. The total cable length may not exceed 50
meters. Using so-called RS485 repeaters, several network
segments can be combined to form a network comprising a
maximum of 127 nodes.
The data signalling rate in an MPI/DP network is max. 12
Mbit/s.
Der Adapter unterstützt Übertragungsraten bis max.
1,5 Mbit/ s.
Note
Also refer to “S7-300, Hardware and Installation”.
Warning
!
4
If the transmission rate is 187.5 Kbits/sec and
higher, it i s n o t allowed to insert cable extensions
in the S7/M7/C7 adapter system connection
(spur lines not allowed).
A5E00078070-02
PC/TS Adapter
PC/TS AdapterQuick Reference Guide
5Prerequisites for Operation
5.1Hardware
PC/programming device with a free COM port (COM1 or
COM2, 9-pin COM connection). Appropriate adapters for
other connector combinations are available in specialist
shops, for example 9-pin to 25-pin subminiature D connector.
25-pin subminiature D:
Shield
8
3
2
20
7
6
4
5
22
Shield
1)
1)
Pins or sockets, depending on usage
Signal:
DCD
RXD
TXD
DTR
GND
DSR
RTS
CTS
RI
Connector casingConnector casing
9-pin subminiature D:
Shield
Shield
Figure 1-49-Pin - 25-Pin RS232 Adapter
5.2Software
PC adapter
S STEP 7 Standard Package from V1 or
S S7 DOS
TS adapter
S STEP 7 Standard Package from V3.1 and
S TeleService optional package from Version 3.0
1
2
3
4
5
6
7
8
9
1)
PC/TS Adapter
A5E00078070-02
5
Loading...
+ 19 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.