Siemens 4100 User Manual

Page 1
SpeedStream® 4100 Modem PPPoE Modem Router
Quick-Start Guide
Page 2
• •
2
3
Before you begin,
Verify that the following items came with your DSL kit:
1 SpeedStream® Device
2 Documentation
3 Software Manual CD-ROM
(Router model only)
4 Power supply
5 RJ-45 Straight-through
Ethernet cable
6 RJ-11 DSL cable
1
2
3
Your service provider may include an Ethernet adapter, a line lter, and a wall-mount lter in your DSL kit. If you received any of these items, follow the instructions provided in this guide for basic installation. If you need further assistance installing these items, please contact your service provider.
A PCI Ethernet adapter
B Line lter(s)
C Wall-mount lter
A
B
C
4
5
6
Step 1 >
Install Line Filters
Stand-alone Line Filter
Wall-mount Filter
Devices such as fax machines, caller ID boxes, or phones that share the same phone line as your DSL account require a line lter, which prevents noise from disrupting the DSL signal on the phone line. Filters can be in the form of a stand-alone line lter or a wall-mount lter.
Stand-alone Line Filter
For each device that shares the DSL phone line:
1. Unplug the device’s cord from the phone jack.
2. Plug the lter into the phone jack.
3. Plug the phone cord (or other device cord) into the lter.
Wall-mount Filter
For a wall-mount phone, install a wall-mount lter.
1. Remove the phone.
2. Connect the wall-mount lter to the wall plate.
3. Reconnect the phone.
1
2
3
1
2
3
Page 3
4
5
Step 2 >
Ethernet Installation
Connect the SpeedStream® Device
1. Connect the straight­ through Ethernet cable (RJ-45) to the Ethernet port on the SpeedStream® device (yellow port).
2. Connect the other end of the straight-through Ethernet cable (RJ-45) to the Ethernet port on your computer.
3. Plug the DSL cable (RJ-11) into the DSL port on the SpeedStream® device (gray port).
4. Plug the other end of the DSL cable (RJ-11) into the phone jack.
5. Plug the power adapter into the power outlet and SpeedStream® device (black port).
6. Ensure the SpeedStream® device is powered on (power switch located on right side of back panel).
Install Ethernet Adapter
You will need to install an Ethernet adapter if your computer does not already have one installed. Refer to your Ethernet adapter manufacturer’s documentation for complete installation instructions.
Internet connection
Ethernet connection to computer RJ-45 Straight-through Ethernet cable
Optional: use crossover (Xover) cable when connecting to a hub or switch without an “uplink” port
Power supply
Hub
RJ-11 DSL cable
1
2
3
4
6
5
Step 3 >
PC Conguration Procedures
Windows Configuration
In order to setup the SpeedStream® device, your PC must rst be congured to obtain an IP address from a DHCP server. Follow the procedure below:
Note: The following procedures cover conguration of a PC running Windows® XP. Please refer to the User Guide on the CD-ROM for help conguring other operating systems.
1. Click Start > Control Panel.
2. Double-click the Network Connections icon.
3. Double-click your Network Card.
4. Click Properties.
5. Select Internet Protocol (TCP/IP).
6. Click Properties.
7. Select Obtain an IP address automatically.
8. Select Obtain DNS server address automatically.
9. Click OK and exit out of the Control Panel.
10. Congure Internet Access using the procedure that follows.
Internet Access
Next, make sure your PC will use the SpeedStream® device (and not Dial-Up Networking) when connecting to the Internet. Follow the procedure below:
1. Click Start > Control Panel.
2. Double-click the Internet Options icon.
3. Click the Connections tab.
4. Click Setup.
5. Click Next
.
6. Click Connect to the Internet
.
7. Click Next
.
8. Click Setup my connection manually.
9. Click Next
.
10. Select Connect using a broadband
connection that is always on
.
11. Click Next
.
12. Click Finish
.
13.
If you have a router, congure the router using the Router Conguration procedure that follows.
Router Conguration
Windows Me and XP users: If you have Universal Plug and Play (UPnP) enabled, Windows may detect the SpeedStream® device upon startup and provide a shortcut to the device on the desktop or system task tray. The icon will be labeled as “Residential Gateway.” Double-click the icon and skip to step 3.
1. Start your Web browser.
2. In the Address box, enter the following: http://speedstream
3. When prompted for a username and password, type admin for the password only (username is not required).
4. Click Login and enter the username and password provided by your service provider.
5. Click Save.
6. If additional conguration is desired, select Setup to congure DHCP, rewall settings, security options, and also to view status and statistical information.
Note: If your Service Provider requires you to use separate PPPoE client software, discontinue use of this software. The SpeedStream® device will negotiate the PPPoE logon to your service provider’s network.
Congratulations! You have completed the installation of your SpeedStream® device.
Page 4
7
Macintosh Conguration Procedures
Follow the procedure below for OSX:
1. Click Apple -> System Preferences.
2. Select the Network icon under the Internet & Network section.
3. Select Built-in Ethernet from the Show drop-down menu.
4. Select Using DHCP Server from the Congure IPv4 drop-down menu.
5. Click Apply Now and exit out of System Preferences window.
6. If you have a router, congure the router using the Router Conguration procedure that follows.
Follow the procedure below for OS9:
1. Click Apple -> Control Panels -> TCP/IP.
2. Select Ethernet from Connect via drop-down menu.
3. Select Using DHCP Server from the Congure drop-down menu.
4. Close window and save changes.
5. If you have a router, congure the router using the Router Conguration procedure that follows.
Router Conguration
1. Start your Web browser.
2. In the Address box, enter the following: http://speedstream
3. When prompted for a username and password, type admin for the password only (username is not required).
4. Click Login and enter the username and password provided by your service provider.
5. Click Save.
6. If additional conguration is desired, select Setup to congure DHCP, rewall settings, security options, and also to view status and statistical information.
Macintosh Configuration
In order to setup the SpeedStream® device, your computer must rst be congured to obtain an IP address from a DHCP server.
Congratulations! You have completed the installation of your SpeedStream® device.
6
Troubleshooting
LED Off Green Blinking
Green
Red Blinking
Red/Green
Power - Power not
applied
Normal system operation
N/A Self-test
failure if red for more than 30 seconds
Flash write in progress
Ethernet - Power not
applied
- Ethernet link not connected
Ethernet link connected
Ethernet trafc owing in either direction
N/A N/A
DSL - Power not
applied
- DSL signal not detected
DSL line is trained and ready for trafc
DSL is training N/A N/A
Internet - Power not
applied
- No connection to Internet
Bridge: DSL Link is up Router: DSL link is up + WAN interface is up + WAN interface has an IP address
N/A N/A N/A
Activity
- Power not applied
- No LAN data activity
N/A LAN user trafc
owing in either direction
N/A N/A
Page 5
8
Siemens Subscriber Networks, Inc. 4849 Alpha Road Dallas, TX 75244 (972) 852-1000 Fax (972) 852-1001 usa.800siemens@icn.siemens.com http://www.icn.siemens.com/subscriber
Copyright© 2004 SIEMENS SUBSCRIBER NETWORKS, INC. All rights reserved. Siemens and the Siemens logo are trademarks of Siemens AG, Germany. All other trademarks are held by their respective companies. Siemens reserves the right to make changes to product specications at any time without notice.
Loading...