SIMATIC CPU 1515SP PC2 F,SIMATIC CPU 1515SP PC2 T,SIMATIC CPU 1515SP PC2 TF
Table of contents
Loading...Siemens SIMATIC CPU 1515SP PC2 F,SIMATIC CPU 1515SP PC2 T,SIMATIC CPU 1515SP PC2 TF User Manual
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
SIMATIC
ET 200SP Open Controller
CPU 1515SP PC2 (F/T/TF)
Operating Instructions
09/2018
A5E42603425
Introduction
1
Safety information
2
Areas of application
3
Product overview
4
Application planning
5
Installation
6
Wiring
7
Commissioning
8
Interrupt, error and system
messages
9
Functions
10
Maintenance
11
Technical specifications
12
Dimension drawings
13
Spare parts/accessories
14
Appendix
A
List of abbreviations
B
-AA
Siemens AG
Division Digital Factory
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E42603425-AA
Ⓟ
Copyright © Siemens AG 2018.
All rights reserved
Legal information
Warning notice system
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
Qualified Personnel
personnel qualified
Proper use of Siemens products
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
Disclaimer of Liability
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
The product/system described in this documentation may be operated only by
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Note the following:
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
for the specific
07/2018 Subject to change
Table of contents
1 Introduction ............................................................................................................................................. 6
2 Safety information ................................................................................................................................. 13
3 Areas of application .............................................................................................................................. 17
4 Product overview .................................................................................................................................. 18
5 Application planning .............................................................................................................................. 28
6 Installation ............................................................................................................................................ 34
7 Wiring ................................................................................................................................................... 36
1.1 Documentation on CPU 1515SP PC2 ...................................................................................... 8
1.2 Information about third-party software updates ...................................................................... 12
1.3 Notes on protecting administrator accounts ........................................................................... 12
2.1 Security information ................................................................................................................ 13
2.2 General safety instructions ..................................................................................................... 14
2.3 Notes on use ........................................................................................................................... 16
3.1 Areas of application of fail-safe CPUs .................................................................................... 17
3.2 Areas of application of technology CPUs ............................................................................... 17
4.1 Field of application .................................................................................................................. 18
4.2 Characteristics ........................................................................................................................ 19
4.3 Sample configuration .............................................................................................................. 20
4.4 Components ............................................................................................................................ 22
4.5 Operator controls and connection elements ........................................................................... 24
4.6 Scope of delivery .................................................................................................................... 27
5.1 Basics...................................................................................................................................... 28
5.2 Unpacking the device.............................................................................................................. 29
5.3 Identification data .................................................................................................................... 30
5.4 Installation location ................................................................................................................. 31
5.5 Hardware configuration ........................................................................................................... 33
6.1 Installing the device ................................................................................................................ 34
7.1 Notes on connection ............................................................................................................... 36
7.2 Terminal and block diagram ................................................................................................... 37
7.3 Electrical configuration ............................................................................................................ 38
7.4 Connecting devices to networks ............................................................................................. 40
CPU 1515SP PC2 (F/T/TF)
Operating Instructions, 09/2018, A5E42603425-AA
3
Table of contents
8 Commissioning ..................................................................................................................................... 42
9 Interrupt, error and system messages ................................................................................................... 51
10 Functions .............................................................................................................................................. 54
11 Maintenance ......................................................................................................................................... 58
12 Technical specifications ........................................................................................................................ 66
7.5 Securing cables...................................................................................................................... 41
8.1 Notes on commissioning ........................................................................................................ 42
8.2 Basic commissioning procedure ............................................................................................ 43
8.2.1 Requirements ......................................................................................................................... 43
8.2.2 Preparing commissioning ....................................................................................................... 43
8.2.3 Commissioning procedure ..................................................................................................... 43
8.3 Initial commissioning an open controller ................................................................................ 45
8.3.1 Creating the configuration of the Open Controller ................................................................. 45
8.3.2 Setting the IP address ............................................................................................................ 46
8.3.3 Changing the properties of the S7-1500 Software Controller ................................................ 46
8.3.4 Establishing the HMI connection............................................................................................ 47
8.3.5 Downloading a project to the target system ........................................................................... 47
8.3.6 Transferring license keys ....................................................................................................... 48
8.3.7 Switching the Open Controller on/off ..................................................................................... 50
9.1 Status and error display ......................................................................................................... 51
10.1 Monitoring functions ............................................................................................................... 54
10.1.1 Requirements ......................................................................................................................... 54
10.1.2 Temperature monitoring ......................................................................................................... 55
10.1.3 Monitoring drives .................................................................................................................... 55
10.1.4 Operating hours counter ........................................................................................................ 55
10.2 Retentive memory NVRAM .................................................................................................... 55
10.3 BIOS setup ............................................................................................................................. 56
10.4 Power options ........................................................................................................................ 56
10.5 "Unified Write Filter (UWF)" write filter ................................................................................... 57
11.1 Backing up and restoring data ............................................................................................... 58
11.2 Partitions in the delivery state ................................................................................................ 59
11.3 Restoring the delivery state ................................................................................................... 60
11.4 Updating software .................................................................................................................. 62
11.5 Windows 10 IoT Enterprise (64-bit) ....................................................................................... 62
11.6 Sending the device to customer service ................................................................................ 63
11.7 Removing and inserting the CFast card ................................................................................ 64
11.8 Recycling and disposal .......................................................................................................... 65
12.1 Standards and approvals ....................................................................................................... 66
12.2 Electromagnetic compatibility ................................................................................................ 71
12.3 Shipping and storage conditions ............................................................................................ 73
CPU 1515SP PC2 (F/T/TF)
4 Operating Instructions, 09/2018, A5E42603425-AA
Table of contents
13 Dimension drawings ............................................................................................................................ 121
14 Spare parts/accessories ...................................................................................................................... 123
A Appendix............................................................................................................................................. 124
B List of abbreviations ............................................................................................................................ 126
Glossary ............................................................................................................................................. 128
Index................................................................................................................................................... 131
12.4 Mechanical and climatic ambient conditions .......................................................................... 74
12.5 Information on insulation, protection class, degree of protection and rated voltage .............. 76
12.6 Use of the ET 200SP in zone 2 potentially explosive atmospheres ....................................... 77
12.7 Module data ............................................................................................................................ 78
12.7.1 Technical specifications of CPU 1515SP PC2 - basic device ................................................ 78
12.7.2 Technical specifications CPU 1515SP PC2 ........................................................................... 81
12.7.3 Technical specifications of CPU 1515SP PC2 + HMI 128PT ................................................. 85
12.7.4 Technical specifications of CPU 1515SP PC2 + HMI 512PT ................................................. 89
12.7.5 Technical specifications of CPU 1515SP PC2 + HMI 2048PT ............................................... 93
12.7.6 Technical specifications of CPU 1515SP PC2 F .................................................................... 97
12.7.7 Technical specifications of CPU 1515SP PC2 F + HMI 128PT ............................................ 101
12.7.8 Technical specifications of CPU 1515SP PC2 F + HMI 512PT ............................................ 105
12.7.9 Technical specifications of CPU 1515SP PC2 F + HMI 2018PT .......................................... 109
12.7.10 Technical specifications of CPU 1515SP PC2 T .................................................................. 113
12.7.11 Technical specifications of CPU 1515SP PC2 TF ................................................................ 117
12.7.12 S7-1500 Software Controller CPU 1505SP (F/T/TF) ............................................................ 120
13.1 CPU 1515SP PC2 ................................................................................................................. 121
14.1 Accessories/spare parts........................................................................................................ 123
A.1 Siemens Industry Online Support ......................................................................................... 124
A.2 Industry Mall .......................................................................................................................... 124
A.3 Troubleshooting .................................................................................................................... 125
B.1 Abbreviations ........................................................................................................................ 126
CPU 1515SP PC2 (F/T/TF)
Operating Instructions, 09/2018, A5E42603425-AA
5
1
Purpose of the documentation
Basic knowledge required
These operating instructions supplement the system manual
ET 200SP distributed I/O system. Functions that generally relate to the system are described
in this manual.
The information provided in these operating instructions and in the system/function manuals
supports you in commissioning the CPU 1515SP PC2.
The system must be operated and used by qualified staff only.
The following knowledge is required:
● Installation guideline for SIMATIC ET 200SP
● Totally Integrated Automation Portal, in particular:
– Hardware configuration with
– Communication between CPUs
● PC based automation with an S7-1500 software controller and with
WinCC Runtime Advanced
● Basic knowledge of fail-safe automation systems
● Basic knowledge of PC technology
● Windows 10 IoT Enterprise operating system (64-bit)
hardware and network editor
CPU 1515SP PC2 (F/T/TF)
6 Operating Instructions, 09/2018, A5E42603425-AA
Introduction
Conventions
only
only
only
Note
A note contains important information on the product described in the documentation, on the
handling of the product or on the section of the documentation to which particular attention
should be paid.
Scope of validity of the documentation
ET 200SP Open Controller
Article number
Standard CPU
Fail-safe CPUs
Technology CPUs
Fail-safe technology CPUs
1.1 Documentation on CPU 1515SP PC2
STEP 7: In this documentation, "STEP 7" is used as a synonym for all versions of the
configuration and programming software "STEP 7 (TIA Portal)".
"CPU1515SP PC2 T" means that the respective section applies
"CPU 1515SP PC2 T".
"CPU1515SP PC2 F" means that the respective section applies
"CPU 1515SP PC2 F".
"CPU1515SP PC2 TF" means that the respective section applies
"CPU 1515SP PC2 TF".
"CPU 1515SP PC2" also includes "CPU1 515SP PC2 F", "CPU 1515SP PC2 T" and
"CPU 1515SP PC2 TF".
Please also observe notes marked as follows:
This documentation is valid for the following products:
to the
to the
to the
• CPU 1515SP PC2 basic device
• CPU 1515SP PC2
• CPU 1515SP PC2 + HMI 128PT
• CPU 1515SP PC2 + HMI 512PT
• CPU 1515SP PC2 + HMI 2048PT
• CPU 1515SP PC2 F
• CPU 1515SP PC2 F + HMI 128PT
• CPU 1515SP PC2 F + HMI 512PT
• CPU 1515SP PC2 F + HMI 2048PT
• CPU 1515SP PC2 T
• CPU 1515SP PC2 TF
6ES7677-2DB40-0AA0
6ES7677-2DB42-0GB0
6ES7677-2DB42-0GK0
6ES7677-2DB42-0GL0
6ES7677-2DB42-0GM0
6ES7677-2SB42-0GB0
6ES7677-2SB42-0GK0
6ES7677-2SB42-0GL0
6ES7677-2SB42-0GM0
6ES7677-2VB42-0GB0
6ES7677-2WB42-0GB0
CPU 1515SP PC2 (F/T/TF)
Operating Instructions, 09/2018, A5E42603425-AA
7
Introduction
1.1
Documentation on CPU 1515SP PC2
1.1 Documentation on CPU 1515SP PC2
The following additional documentation is required to use the CPU 1515SP PC2:
● Operating instructions CPU 1505SP (F/T/TF), CPU 1507S (F) Version 2.5
(http://support.automation.siemens.com/WW/view/en/109740725
● STEP 7 and WinCC Engineering V15 system manual
(https://support.industry.siemens.com/cs/ww/en/view/109755202
● ET 200SP distributed I/O system manual
(http://support.automation.siemens.com/WW/view/en/58649293
● ET 200SP server module manual
(http://support.automation.siemens.com/WW/view/en/63257531
● SIMATIC Safety - Configuring and Programming
(http://support.automation.siemens.com/WW/view/en/54110126
● SIMATIC S7-1200/S7-1500 F-CPUs
(http://support.automation.siemens.com/WW/view/en/109478599
The documentation for the SIMATIC ET 200SP distributed I/O system is arranged into three
areas.
This arrangement enables you to access the specific content you require.
)
)
)
)
)
)
CPU 1515SP PC2 (F/T/TF)
8 Operating Instructions, 09/2018, A5E42603425-AA
Introduction
Basic information
Device information
General information
Manual Collection ET 200SP
"mySupport"
"mySupport" - Documentation
1.1 Documentation on CPU 1515SP PC2
The system manual describes in detail the configuration, installation, wiring and
commissioning of the SIMATIC ET 200SP. distributed I/O system. The STEP 7 online help
supports you in the configuration and programming.
Product manuals contain a compact description of the module-specific information, such as
properties, wiring diagrams, characteristics and technical specifications.
The function manuals contain detailed descriptions on general topics regarding the SIMATIC
ET 200SP distributed I/O system, e.g. diagnostics, communication, Web server, motion
control and OPC UA.
You can download the documentation free of charge from the Internet
http://w3.siemens.com/mcms/industrial-automation-systems-simatic/en/manual-
(
overview/tech-doc-et200/Pages/Default.aspx).
Changes and supplements to the manuals are documented in a Product Information.
You can download the product information free of charge from the Internet
(https://support.industry.siemens.com/cs/us/en/view/73021864
The Manual Collection contains the complete documentation on the SIMATIC ET 200SP
distributed I/O system gathered together in one file.
You can find the Manual Collection on the Internet
(http://support.automation.siemens.com/WW/view/en/84133942
With "mySupport", your personal workspace, you make the most of your Industry Online
Support.
In "mySupport" you can store filters, favorites and tags, request CAx data and put together
your personal library in the Documentation area. Furthermore, your data is automatically
filled into support requests and you always have an overview of your current requests.
You need to register once to use the full functionality of "mySupport".
You can find "mySupport" in the Internet (https://support.industry.siemens.com/My/ww/en
).
).
).
In the Documentation area of "mySupport", you have the possibility to combine complete
manuals or parts of them to make your own manual.
You can export the manual in PDF format or in an editable format.
You can find "mySupport" - Documentation in the Internet
(http://support.industry.siemens.com/My/ww/en/documentation
CPU 1515SP PC2 (F/T/TF)
Operating Instructions, 09/2018, A5E42603425-AA
).
9
Introduction
"mySupport" - CAx Data
Application examples
TIA Selection Tool
1.1 Documentation on CPU 1515SP PC2
In the CAx Data area of "mySupport", you can have access the latest product data for your
CAx or CAe system.
You configure your own download package with a few clicks.
In doing so you can select:
● Product images, 2D dimension drawings, 3D models, internal circuit diagrams, EPLAN
macro files
● Manuals, characteristics, operating manuals, certificates
● Product master data
You can find "mySupport" - CAx Data in the Internet
(http://support.industry.siemens.com/my/ww/en/CAxOnline
).
The application examples support you with various tools and examples for solving your
automation tasks. Solutions are shown in interplay with multiple components in the system separated from the focus in individual products.
You can find the application examples on the Internet
(https://support.industry.siemens.com/sc/ww/en/sc/2054
With the TIA Selection Tool, you can select, configure and order devices for Totally
Integrated Automation (TIA).
This tool is the successor of the SIMATIC Selection Tool and combines the known
configurators for automation technology into one tool.
With the TIA Selection Tool, you can generate a complete order list from your product
selection or product configuration.
You can find the TIA Selection Tool on the Internet
(http://w3.siemens.com/mcms/topics/en/simatic/tia-selection-tool
).
).
CPU 1515SP PC2 (F/T/TF)
10 Operating Instructions, 09/2018, A5E42603425-AA
Introduction
SIMATIC Automation Tool
PRONETA
1.1 Documentation on CPU 1515SP PC2
You can use the SIMATIC Automation Tool to run commissioning and maintenance activities
simultaneously on various SIMATIC S7 stations as a bulk operation independently of the
TIA Portal.
The SIMATIC Automation Tool provides a multitude of functions:
● Scanning of a PROFINET/Ethernet network and identification of all connected CPUs
● Address assignment (IP, subnet, gateway) and station name (PROFINET device) to a
CPU
● Transfer of the data and the programming device/PC time converted to UTC time to the
module
● Program download to CPU
● Operating mode switchover RUN/STOP
● Localization of the CPU by means of LED flashing
● Reading out CPU error information
● Reading the CPU diagnostic buffer
● Reset to factory settings
● Updating the firmware of the CPU and connected modules
You can find the SIMATIC Automation Tool on the Internet
(https://support.industry.siemens.com/cs/ww/en/view/98161300
).
With SIEMENS PRONETA (PROFINET network analysis), you analyze the plant network
during commissioning. PRONETA features two core functions:
● The topology overview independently scans PROFINET and all connected components.
● The IO check is a fast test of the wiring and the module configuration of a system.
You can find SIEMENS PRONETA on the Internet
(https://support.industry.siemens.com/cs/ww/en/view/67460624
).
CPU 1515SP PC2 (F/T/TF)
Operating Instructions, 09/2018, A5E42603425-AA
11
Introduction
SINETPLAN
1.2
Information about third-party software updates
1.3
Notes on protecting administrator accounts
1.2 Information about third-party software updates
SINETPLAN, the Siemens Network Planner, supports you in planning automation systems
and networks based on PROFINET. The tool facilitates professional and predictive
dimensioning of your PROFINET installation as early as in the planning stage. In addition,
SINETPLAN supports you during network optimization and helps you to exploit network
resources optimally and to plan reserves. This helps to prevent problems in commissioning
or failures during productive operation even in advance of a planned operation. This
increases the availability of the production plant and helps improve operational safety.
The advantages at a glance
● Network optimization thanks to port-specific calculation of the network load
● Increased production availability thanks to online scan and verification of existing systems
● Transparency before commissioning through importing and simulation of existing STEP 7
projects
● Efficiency through securing existing investments in the long term and optimal exploitation
of resources
You can find SINETPLAN on the Internet.
This product contains third-party software. Siemens accepts liability with respect to
updates/patches for the third-party software only when these are distributed by Siemens in
the context of a Software Update Service contract or officially approved by Siemens.
Otherwise, updates/patches are installed at the user's own risk. You can find more
information about our software update service offer under
http://w3.siemens.com/mcms/topics/en/simatic/licenses/software-update-
(
service/Pages/Default.aspx).
A user with administrator rights has extensive access and manipulation possibilities.
Therefore, make sure that the administrator account is adequately protected to prevent
unauthorized changes. To do this, set secure passwords and use a standard user account
for regular operation. Other measures, such as the use of security policies, should be
applied as required.
CPU 1515SP PC2 (F/T/TF)
12 Operating Instructions, 09/2018, A5E42603425-AA
2
2.1
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens' products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be
connected to an enterprise network or the internet if and to the extent such a connection is
necessary and only when appropriate security measures (e.g. firewalls and/or network
segmentation) are in place.
For additional information on industrial security measures that may be implemented, please
visit (https://www.siemens.com/industrialsecurity
).
Siemens' products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends that product updates are applied as soon as they are
available and that the latest product versions are used. Use of product versions that are no
longer supported, and failure to apply the latest updates may increase customers' exposure
to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under (https://www.siemens.com/industrialsecurity
).
CPU 1515SP PC2 (F/T/TF)
Operating Instructions, 09/2018, A5E42603425-AA
13
Safety information
2.2
General safety instructions
WARNING
Life-endangering voltage when control cabinet is open
Safe operation of a plant
NOTICE
Protective measures
PC2
Repairs
WARNING
Damage caused by opening the device
2.2 General safety instructions
If the device is installed in a control cabinet, areas or components can be under lifeendangering voltage when the control cabinet is open.
Contact with these areas or components may lead to death through electric shock.
Switch off the power before opening the control cabinet.
If the device is operated in a machine in accordance with the machinery directive, the
provisions of the guideline 2006/42/EC apply.
To ensure safe operation of a plant, you have to take suitable IT security measures, for
example, network segmentation.
Seal the cover to protect the CFast card with the operating system of the CPU 1515SP
from unauthorized access.
For more information on Industrial Security, refer to the Internet
(http://www.siemens.com/industrialsecurity
).
If you have questions about whether it is permissible to install the device in the planned
environment, please contact your service representative.
Unauthorized opening of and improper repairs to the device may result in substantial
damage to equipment or endanger the user.
Only authorized personnel are permitted to repair the device.
You can find more information on the repair in the section Sending device in for repair
(Page 63).
CPU 1515SP PC2 (F/T/TF)
14 Operating Instructions, 09/2018, A5E42603425-AA
Safety information
ESD guidelines
2.2 General safety instructions
Modules containing electrostatic sensitive devices (ESDs) can be identified by the following
label:
Strictly follow the guidelines mentioned below when handling modules which are sensitive to
ESD:
● Before working with modules with ESD, you need to ensure that you are free of
electrostatic charge (e.g. by touching a grounded object).
● All devices and tools must be free of static charge.
● Always pull the mains connector and disconnect the battery before installing or removing
modules which are sensitive to ESD.
● Handle modules fitted with ESDs only by their edges.
● Do not touch any connector pins or conductors on modules containing ESDs.
CPU 1515SP PC2 (F/T/TF)
Operating Instructions, 09/2018, A5E42603425-AA
15
Safety information
2.3
Notes on use
WARNING
Hazards at an unprotected machine or plant
NOTICE
Ambient conditions
2.3 Notes on use
According to the results of a risk analysis, hazards can occur at an unprotected machine.
The hazards may lead to personal injury.
According to the risk analysis, the risk of injury to persons can be countered with the
following measures:
• Additional protective equipment at the machine or plant. In this case, the programming,
parameter assignment and wiring of the I/O used, in particular, must be performed in
accordance with the safety criteria (SIL, PL or Cat.) ascertained by means of an
appropriate risk analysis.
• Use of the device for its intended purpose, which can be established by performing a
functional test on the plant. This allows errors in programming, parameter assignment
and wiring to be detected.
• Documentation of the test results which can be entered, if required, into the relevant
safety certificates.
Ambient conditions for which the device is not suitable can lead to faults or damage the
device.
Note the following:
• Only operate the device in enclosed areas. If you do not comply with this instruction, the
warranty becomes void.
• Only operate the device in accordance with the ambient conditions given in the technical
specifications.
• Protect the device from dust, moisture and heat.
• Do not expose the device to direct sunlight or other strong sources of light.
• The device must not be used in places with more difficult operating conditions through
corrosive vapors or gases without taking additional protective measures, for example,
supply of clean air.
CPU 1515SP PC2 (F/T/TF)
16 Operating Instructions, 09/2018, A5E42603425-AA
3
3.1
Areas of application of fail-safe CPUs
Areas of application
Reference
3.2
Areas of application of technology CPUs
Areas of application
Reference
F-CPUs are mainly designed for personal and machine protection. In addition to the safety
program, you can also program standard applications. You can operate the F-CPUs in safety
mode or in standard mode.
Information on the use of F-CPUs in safety mode is available in the programming and
operating manual SIMATIC Safety - Configuring and Programming
(http://support.automation.siemens.com/WW/view/en/54110126
).
You can find information on using the CPU 1505SP (F) Software Controller in the associated
manual (https://support.industry.siemens.com/cs/ww/en/view/109740725
F-product information (https://support.industry.siemens.com/cs/ww/en/view/109478599).
Areas of application of T-CPUs are motion control applications such as gearing and
camming as well as control of kinematics. Due to the supported technology functions, the
S7-1500T CPUs are suitable for controlling packaging machines, converting applications,
assembly automation, etc.
You can operate the TF-CPUs in safety mode or in standard mode.
You can find information on using the T-CPUs in the function manual SIMATIC S7-1500T
Motion Control (http://support.automation.siemens.com/WW/view/en/109749263
You can find information on using the T-CPUs in the function manual SIMATIC S7-1500T
kinematics functions (http://support.automation.siemens.com/WW/view/en/109749264
) and in the
).
).
You can find information on using the F-CPUs and TF-CPUs in safety mode in the product
information for SIMATIC S7-1200/S7-1500 F-CPUs
(http://support.automation.siemens.com/WW/view/en/109478599
CPU 1515SP PC2 (F/T/TF)
Operating Instructions, 09/2018, A5E42603425-AA
).
17
4
4.1
Field of application
Article number
View of the module
The article number depends on the pre-installed S7-1500 Software Controller and
HMI Runtime.
You can find an overview of the article numbers in the section Scope of validity of the
documentation (Page 6).
The following figure shows the CPU 1515SP PC2:
Figure 4-1 CPU 1515SP PC2 with supplied accessories
CPU 1515SP PC2 (F/T/TF)
18 Operating Instructions, 09/2018, A5E42603425-AA
Product overview
4.2
Characteristics
General characteristics
Additional information
4.2 Characteristics
The CPU 1515SP PC2 is a PC-based automation device in the design of the ET 200SP. It is
used for control and visualization purposes. The supplied IPC DiagBase software provides
basic diagnostics functions and supports you in handling the BIOS.
● A removable CFast card with the following pre-installations is used as storage medium:
– Windows 10 IoT Enterprise operating system (64-bit)
– S7-1500 Software Controller CPU 1505SP, CPU 1505SP F, CPU 1505SP T,
CPU 1505SP TF
– Optionally with HMI: WinCC Runtime Advanced as of V15
● Interfaces:
– An interface for the exchangeable ET 200SP BusAdapters for connection of
PROFINET IO (2 ports) Accessories/spare parts (Page 123)
– An interface for connecting devices using Industrial Ethernet (Gigabit Ethernet)
– 4 interfaces for USB devices (2 x USB 3.0 and 2 x USB 2.0)
– A DisplayPort interface (DPP) for a monitor
– A sealable slot for the CFast card
– A slot for an SD/MMC card as additional optional drive
● Supply voltage 1L+ 24 V DC (SELV/PELV). The connection plug is included in the scope
of delivery.
● The CPU 1515SP PC2 is suitable for use in industrial environments:
– Compact design
– Fan-less operation
– High robustness
● The CPU 1515SP PC2 complies with IP 20 degree of protection and is intended for
installation in a control cabinet.
You can find more information on the system versions and ordering options in the section
Scope of validity of the documentation (Page 6).
CPU 1515SP PC2 (F/T/TF)
Operating Instructions, 09/2018, A5E42603425-AA
19
Product overview
4.3
Sample configuration
Configuration
4.3 Sample configuration
The CPU 1515SP PC2 is mounted on a mounting rail according to EN 60715. A modular
system is formed with ET 200SP modules in the central rack. You can also expand the
CPU 1515SP PC2 with fail-safe I/O modules.
You can use the CPU 1515SP PC2 as PROFINET IO controller. The PROFINET IO devices
are connected via the ports of the X1 PN(LAN) interface using a SIMATIC BusAdapter.
Devices can be connected via Industrial Ethernet using the integrated interface
X2 PN/IE(LAN).
The connection to PROFIBUS can be made using the DP master module.
CPU 1515SP PC2 (F/T/TF)
20 Operating Instructions, 09/2018, A5E42603425-AA
Product overview
Sample configuration
①
CPU 1515SP PC2, I/O modules, server module, BusAdapter
②
ET 200AL modules with ET-Connection
③
Flat Panel - Wide Screen Display
④
USB devices: Keyboard, mouse, printer ...
⑤
Industrial Thin Client ITC
⑥
SCALANCE W786
⑦
Field PG
⑧
PROFINET IO device
⑨
Camera
⑩
PC/Programming device
Reference
4.3 Sample configuration
The following figure shows a sample configuration with the CPU 1515SP PC2:
Figure 4-2 Configuration example with the CPU 1515SP PC2
You can find more information about configuring the ET 200AL modules in the system
manual ET 200AL distributed I/O system
(https://support.industry.siemens.com/cs/ww/en/view/89254965
).
CPU 1515SP PC2 (F/T/TF)
Operating Instructions, 09/2018, A5E42603425-AA
21
Product overview
4.4
Components
Components of the CPU 1515SP PC2
Component
Function
Figure
4.4 Components
The following table provides an overview of the components of the CPU 1515SP PC2:
Table 4- 1 Components of the CPU 1515SP PC2
Mounting rail in accordance
with EN 60715
CPU 1515SP PC2 CPU with strain relief and white refer-
The mounting rail is the rack for the
CPU 1515SP PC2.
ence labels
CPU 1515SP PC2 (F/T/TF)
22 Operating Instructions, 09/2018, A5E42603425-AA
Product overview
Component
Function
Figure
4.4 Components
BusAdapter The BusAdapter allows free selection
of the connection technology for
PROFINET IO.
The following versions are available
for CPU 1515SP PC2:
• For standard RJ45 connector
(BA 2×RJ45) ①
• For direct connection of the bus
cable (BA 2×FC) ②
• For POF/PCF fiber-optic cable
(BA 2xSCRJ) ③
• As media converter for POF/PCF
fiber-optic cable ⇔ standard RJ45
connector (BA SCRJ/RJ45)
• As media converter for POF/PCF
fiber-optic cable ⇔ direct connec-
tion of the bus cable
(BA SCRJ/FC)
• For glass fiber-optic cable
(BA 2xLC) ⑥
• As media converter for glass fiber-
optic cable ⇔ standard RJ45 connector (BA LC/RJ45)
• As media converter for glass fiber-
optic cable ⇔ direct connection of
the bus cable (BA LC/FC)
For mixed configuration with an
ET 200AL , you require the
BusAdapter BA-Send 1xFC
(plugged into the BaseUnit BU-Send).
Connect the bus cable for ET-
Connection to the BusAdapter
BA-Send 1xFC.
⑤
④
⑦
⑧
①
Server module The server module completes the
configuration of the
CPU 1515SP PC2 with I/O modules.
The server module is included in the
CPU's scope of delivery.
CPU 1515SP PC2 (F/T/TF)
Operating Instructions, 09/2018, A5E42603425-AA
23
Product overview
4.5
Operator controls and connection elements
View of the module
①
Reference identification labels
②
Mounting rail release
③
Labeling strips
④
LEDs for the current operating state and diagnostic status of the CPU 1505SP
⑤
Power LED
⑥
Server module
⑦
X50:
Slot for the CFast card (flash memory), sealable
⑧
Mode selector
⑨
X51:
Slot for an optional SD/MMC card
⑩
X80:
Connector for 24 V DC supply voltage
⑪
Cooling fins
⑫
X1 PROFINET (LAN):
Slot for BusAdapter for connection of PROFINET IO;
Status display for PROFINET
⑬
X2 PN/IE(LAN):
GbE Ethernet connection with integrated display
⑭
Strain relief
⑮
X62, X63:
2 x USB 2.0 ports
⑯
X60, X61:
2 x USB 3.0 ports
⑰
X70:
DisplayPort interface (DPP)
4.5 Operator controls and connection elements
The following figure shows the operator controls and connection elements of the
CPU 1515SP PC2:
Figure 4-3 View of the CPU 1515SP PC2
CPU 1515SP PC2 (F/T/TF)
24 Operating Instructions, 09/2018, A5E42603425-AA
Product overview
Slot for CFast card
Note
Unauthorized access
Seal the cover of the slo
CPU
Slot for SD/MMC card
USB connections
MAC addresses
Assignment
MAC address 1
MAC address 2
MAC address 3
Port X1 P1 (required for LLDP, for example)
MAC address 4
4.5 Operator controls and connection elements
The operating system, Runtime software and project are installed on the supplied
SIMATIC CFast card. The CFast card is the only mass storage device of the
CPU 1515SP PC2.
t to protect the CFast card with the operating system of the
1515SP PC2 from unauthorized access and manipulation.
You can use a SIMATIC SD or MMC card as additional storage drive. This drive can be used
to store data via Windows, for example a backup, but not the operating system, the Runtime
software or the project.
Permitted SD cards: SDHC up to 32 GB, SDXC up to 2 TB.
● 2 x USB 3.0 with I
● 2 x USB 2.0 with I
= 1 A per interface
max
= 0.5 A per interface
max
The MAC address consists of a 3-byte manufacturer ID and a 3-byte device ID (consecutive
number).
Each device is already assigned four MAC addresses in the factory. The front of the
CPU 1515SP PC2 is lasered with the MAC address 1 and 4. With the MAC addresses 2 and
3, the consecutive numbers are incremented. If, for example, the first MAC address is
08-00-06-6B-80-C0, the second MAC address is 08-00-06-6B-80-C1.
Table 4- 2 Assignment of the MAC addresses
X2 PN/IE(LAN)
• Visible in STEP 7 for accessible devices
• Lasered on the front of the CPU (start of the number range)
X1 PROFINET (LAN)
• Visible in STEP 7 for accessible devices
Port X1 P2 R (required for LLDP, for example)
CPU 1515SP PC2 (F/T/TF)
Operating Instructions, 09/2018, A5E42603425-AA
• Lasered on the front of the CPU (end of the number range)
25
Product overview
Connector for supply voltage
Mode selector
Position
Meaning
Description
RUN
Operating mode RUN1
The CPU is processing the user program.
The outputs are set to a "safe" state.
For active S7-1500 software controller
CPU memory reset
1
selected
actual
2
See manual S7-1500 Software Controller CPU 1505SP (F), CPU 1507S (F) Version 2
4.5 Operator controls and connection elements
The CPU 1515SP PC2 is equipped with a 2-pin connection terminal for the power supply.
The connection plug for the supply voltage is plugged in when the CPU is shipped from the
factory.
Use the mode selector to set the CPU operating mode.
Table 4- 3 Mode selector positions
STOP Operating mode STOP1 The CPU is not processing the user program.
MRES Memory reset
RUN and STOP indicate the
the CPU 1515SP PC2.
operating state. The RUN and STOP LEDs indicate the
2
only:
operating mode of
CPU 1515SP PC2 (F/T/TF)
26 Operating Instructions, 09/2018, A5E42603425-AA
Product overview
4.6
Scope of delivery
Note
The device always comes with the CPU 1515SP PC2
6ES7677
only
Only
4.6 Scope of delivery
label with article number
-2DB40-0AA0, regardless of the order options.
The following components are included in the scope of delivery of the CPUs:
● CPU 1515SP PC2 basic device
● Strain relief with fixing screws
● Server module
● CFast card with the following pre-installations:
– Windows 10 IOT Enterprise operating system (64-bit)
– S7-1500 Software Controller CPU 1505SP
– Optional
of V15
● Restore USB stick for image restore
● Windows-Certificate of Authenticity (CoA)
● Certificate of License (CoL)
●
for CPU 1515SP PC2 (F) with HMI and CPU 1515SP PC2 T/ TF: USB stick with
SIMATIC license keys
● Product information
for CPU 1515SP PC2/CPU 1515SP PC2 F: WinCC RT Advanced as
CPU 1515SP PC2 (F/T/TF)
Operating Instructions, 09/2018, A5E42603425-AA
27
5
5.1
Basics
Introduction
Installation location
Installation position
NOTICE
Damage to the modules
50 °C for an installation with up to 32 I/O modules.
The CPU 1515SP PC2 is open equipment. This means you may only set up the CPU in
enclosures, cabinets or electrical equipment rooms and in a dry environment (IP20 degree of
protection). The housings, cabinets and electrical operating rooms must guarantee
protection against electric shock and spread of fire. The requirements regarding mechanical
strength must also be observed. The housings, cabinets, and electrical operating rooms
must not be accessible without a key or tool. Access may only be possible for instructed or
authorized personnel.
Install the CPU 1515SP PC2 in a suitable enclosure/control cabinet with at least IP54 degree
of protection according to EN 60529 and take into consideration the ambient conditions for
operating the devices.
You can install the ET 200SP distributed I/O system in any position. The preferred mounting
position is horizontal mounting on a vertical wall.
Depending on the mounting position, restrictions on ambient temperature and maximum
configuration apply to the CPU 1515SP PC2.
Modules can be damaged if exposed to ambient temperatures higher than permitted.
The following ambient temperatures must not be exceeded during operation:
• Horizontal mounting
• Vertical mounting
60 °C for an installation with up to 32 I/O modules.
55 °C for an installation with up to 64 I/O modules.
Additional information can be found in the section Mechanical and climatic environmental
CPU 1515SP PC2 (F/T/TF)
28 Operating Instructions, 09/2018, A5E42603425-AA
conditions (Page 74).
Application planning
5.2
Unpacking the device
When unpacking
NOTICE
Damage to the device during transport and storage
NOTICE
Damage to the device caused by condensation
5.2 Unpacking the device
When unpacking, make sure to check the following:
● Check packaging and contents for visible damage from transport. Damaged or
incomplete devices should never be commissioned.
● Check the delivery for correctness and completeness.
Please inform your Siemens contact partner should you notice any irregularities.
● Keep the supplied documentation and licenses. They belong to the device and are the
proof that you have purchased the software preinstalled on the CFast card.
Documentation and licenses are required for initial commissioning and for any questions
that arise.
● Keep the original packaging in case the device needs to be transported again.
● Note the identification data (Page 30) of the device.
If a device is transported or stored without packaging, it is unprotected from shocks,
vibrations, pressure and moisture. Damaged packaging indicates that environmental
conditions have already had a significant impact on the device.
The device might be damaged.
Do not dispose of the original packaging. Pack the device for transport and storage.
If the device was exposed to low temperatures or extreme variations in temperature during
transport, this may cause moisture to build up on or in the device (condensation). Please
note the specified mechanical and climatic ambient conditions (Page 74).
Moisture can cause short-circuits in the electrical circuits and damage the device.
Proceed as follows to avoid damage:
• Store the device in dry conditions.
• Make sure it adapts to room temperature before commissioning.
• Do not expose the device to direct heat radiation from a heater.
• If condensation has developed, wait until the device is completely dry before you switch
it on.
CPU 1515SP PC2 (F/T/TF)
Operating Instructions, 09/2018, A5E42603425-AA
29
Loading...