Siemens Landis & Staefa REV11 Series Operating Instructions Manual
Operating instructions
Landis & Staefa REV11…
REV11… - the temperature controller that allows you to set the ideal room temperature at the
time you want. There are two switching patterns available that can be set to suit your specific
needs. You can either rely on the factory settings or make settings tailored to your personal
needs.
Setting slider
Changing the setting values
Display
Settings
Time of day
Room temperature
(measured)
Time of day
Remote operation active
(if connected)
Standby
Normal temperature
Heating on
Economy temperature
Replace batteries
°C
1.5V 'AA'
1.5V 'AA'
Operation
Continuous
normal temperature
Continuous
economy temperature
Standby
with frost protection
Operating mode
selector
Change
between normal and
economy mode up to the
next switching point
Warmer/colder setting
valid up to the next
switching point
(increments of 0.2 ºC,
± 4 ºC max.)
24-hour mode A
with 2 heating periods
Auto
Run
A1 A2 A3 A4
B1 B2
Operating
position
Auto
Run
Economy
temperature
Normal
temperature
Switching times
B1...B2
B1
B2
Switching times
A1...A4
A1
A2 A3 A4
2222Z11E
24-hour mode B
with 1 heating period
A
B
Commissioning with quick startup
The controller is supplied with factory-set switching patterns, switching times and
temperatures. To commission it, proceed as follows:
1.5V 'AA'
1.5V 'AA'
Remove the black transit tabs from the two batteries. Check to see if the battery
holder is in its correct position. The controller switches itself on.
Move the setting slider to the time position.
Press buttons to set the correct time of day.
Auto
Run
Move the setting slider back to position on the right, because only that position
allows you to close the cover.
A
Select the required operating mode with the operating mode selector (e.g.
A
).
Fold up the operating instructions again, place them back into the cover and close the cover
again.
Do you want to use automatic
operation?
If that is the case, set the operating
mode selector to one of the
following positions:
A
You use the 24-hour setting A with
two
heating periods.
B
You use the 24-hour setting B with
one
heating period.
Do you require continuous normal
temperature?
Move the operating mode selector
to «Normal temperature». This
ensures continuous heating to the
normal temperature. The display
shows
.
Do you require continuous economy
temperature?
Move the operating mode selector
to «Economy temperature». This
ensures continuous heating to the
economy temperature. The display
shows
.
Do you require continuous standby
with frost protection?
Move the operating mode selector
to «Standby». In that case, heating
is provided only when the room
temperature falls below the preset
frost protection limit (5 °C). The
display shows
.
Do you feel too warm or too cold?
°C
By pressing these buttons, you
increase or decrease the actual
room temperature in increments of
0.2 °C by a maximum of ± 4°C. The
display first shows the newly
selected temperature and then the
actual value again.
These
changes are valid only up to the
next switching point.
If, as a
result of the factory settings, you
always feel either too warm or too
cold, you should readjust the
temperature
or to suit your
needs
.
CE1B2222E / 27.01.1999 Subject to alteration Siemens Building Technologies / Landis & Staefa Division
Do you want to change the
temperature level or will you be
absent for a short period of time?
When pressing this button, you
change from the current
temperature level to the other. The
display shows either
, when the
change was made from the
economy temperature, or
, when
it was made from the normal
temperature. This means you can
select the economy temperature
during the time you are absent.
These changes are valid only up
to the next switching point.
Do you want to enter your own
temperatures and heating periods?
The controller has two different switching
patterns (A/B).
Proceed as follows:
A1
Move the setting slider to the
switching position (e.g. A1) and
press
to enter the required
switching time.
All the other
switching positions (A2…A4 and
B1…B2) are set the same way.
Select «Normal temperature» and
press
to set the required value.
Select «Economy temperature»
and press
to set the required
value.
Auto
Run
Move the setting slider back to this
position and close the cover.
Table for entering selected values
Enter the values set by you in the following
table. The numbers already contained in the
table represent factory settings.
Temp.Switching times
A1 A2
A3
A4 B1 B2
6.00 9.00 17.00 22.00 7.00 23.00 20° C 16° C
2222Z12E
Do you need to change the time of
day?
Move the setting slider to the time
of day position and press
to
set the correct time of day.
Auto
Run
Move the setting slider back to this
position and close the cover.
Do you wish to return to the factory
settings?
°C
By pressing these three buttons
simultaneously, a complete reset is
made, which means that the
switching times and temperatures
will be reset to their default values.
Caution: all individual settings
will be lost!
At the same time, a
display check is made, which looks
as follows:
2222Z13
Does the symbol appear in the
display?
If this symbol appears, you need to replace
the batteries within the next three months.
Do you want to change the batteries?
•
Get two new alcaline batteries type AA,
1.5 V.
•
Remove the battery holder, then the
batteries, insert the new batteries and
replace the battery holder.
Caution: The
setting data are maintained fora
maximum of one minute only!
•
Make certain the old batteries are
disposed of properly, in compliance with
environmental requirements.
Energy saving tips without sacrificing
comfort
•
Never allow room temperatures to exceed
21 °C.
•
Press
to change to economy
temperature, even if you are absent for
short periods of time only.
•
Air out the rooms for short periods of time
only, but properly, with the windows wide
open.
Auxiliary functions
Your room temperature controller provides a
number of auxiliary functions, but these
should only be set by your heating engineer.
Loading...