Siemens HB30D50U User Manual
Built-in Ovens
Installation Manual
Manuel D'Installation pour le four
Manual de Instalación para el horno
Models: HB30S50U, HB30D50U
Please read
Important: Save these
Merci
Por favor lee los instrucciones antes del uso.
de lire
Impor
Impor
tant
tante:
instructions before
instructions.
instructions avant utilisation.
:
Conser
Guar
da
ces instructions.
er
v
esos instrucciones.
using.
Safety Instructions
Table of Contents
the oven.
the oven. Never allow children to play with
packaging material.
and grounded by a qualifi ed technician
accordance with the National Electrical Code ANSI/
NFPA No. 7 latest edition (or the Canadian Electric
Code) and local electrical code requirements.
Important: Local codes vary. Installation, electrical
connections and grounding must comply with all
applicable codes.
provided in the literature package for this
oven.
Ask your dealer to recommend a qualifi ed
technician
and an authorized repair service.
to the
oven at the circuit breaker or fuse box in case of
an emergency.
appliance unless specifi cally recommended
in the manuals.
All other servicing should be
done by a qualifi ed technician. This may reduce
the risk of personal injury and damage to the
oven.
oven
by removing panels, wire covers, screws, or
any other part of the product.
DO NOT LIFT OVEN BY DOOR HANDLE.
Remove the door for easier handling and installa-
tion. See ‘Removing the Oven Door’ in the Mainte-
nance section of the Use and Care Manual.
WARNING
..........................................................................................................................
4
WARNING
Preparation
Installation
Final Steps
English • 1
Safety Instructions
The single oven can be installed under a counter or
in a wall or cabinet. The double oven can be
installed in a wall or cabinet.
Choose a location away from strong drafts and
where electrical power can be provided.
The oven support surface must be a minimum 3/4”
thick plywood platform. For single ovens, it must
support 150 pounds. For double ovens, it must
support 290 pounds. The platform must be solid,
level and fl ush with the bottom of the cabinet cut
out.
Warning
Turn power off at service panel and
The junction box must be located in the indicated
the oven will be located.
Verify that wiring to house is adequate.
Verify that wiring inside house is adequate.
Volts
Watts
Amps
Table 2: Electrical Specifi cations
A
47 5/8”
47 5/8”
Top of Cutout to Opening Above
Top of Cutout to Top of Counter
4 1/2” min
4 1/2” min
Preparation
Electrical Specifi cations
Installation
Final Steps
Safety Instructions
Electrical
supply
junction box
D
A
B
C
F
E
Electrical
supply
junction box
B
A
E
C
F
Preparation
Installation
Final Steps
English • 3
Safety Instructions
Verify that electric to the junction box has been turned
must be suitable for the rating of the appliance per
the National Electrical Code requirements or the
Canadian Electric Code requirements.
The fl exible conduit extending from the oven
should be connected directly to the junction box.
The junction box should be located to allow as
much slack as possible between the junction box
and the oven.
A UL listed conduit connector must be provided at
each end of the power supply cable.
The four wire branch circuit connection is
preferred, but where local codes permit, a three
wire branch circuit connection is also acceptable.
(Preferred Method)
bare) ground wire in junction box.
box.
junction box.
4. Connect white wire from oven to white (or gray)
neutral wire in junction box.
Three Wire Connection :
The four wire connection is preferred, but
where local codes permit, the three wire connection is
box.
junction box.
from oven to white (or gray) neutral wire in
junction box.
The oven is pre-wired for connection to 240 V, 60 Hz supply,
door (upper oven in double ovens)
4
Turn knob clockwise
until 6 double beeps sound.
Turn knob counterclockwise
until 9 double beeps
TART.
Time of day clock appears in display.
Preparation
Installation
Final Steps
Loading...