Siemens DESIGO PX, DESIGO PXA40-RS Series, DESIGO PXA40-RS1, DESIGO PXA40-RS2, DESIGO PXC001.D Series Manual

...

Download

Page 1

223

DESIGO™ PX

System controllers

PXC001.D PXC001 PXA40-RS...

for the integration of third-party devices and systems in Desigo

-E.D

• Integration platforms and system controllers for third-party devices and

systems via KNX, Modbus, M-Bus and other protocols into the automation level via BACnet

• System controllers for the integration of Desigo RXB/RXL room controllers

• Native BACnet devices with communication via BACnet/LonTalk or

BACnet/IP

• BTL label (BACnet communications passed the BTL test)

• Comprehensive management and system functions (alarm management,

time scheduling, trends, remote management, access protection etc.)

• Supports operation via local or network-compatible operator units PXM…

CM1N9223en_01 2014-04-04

Building Technologies

Page 2

Use

System controllers

Type

or SCL over BACnet/LonTalk

PXC001.D or SCL over BACnet/IP

PXC001-E.D Option modules

Type

Up to 800 data points

PXA40-RS1

M- Bus and Modbus: up to 2000 data points)

PXC001.D PXC001-E.D

PXA40-RS1

PXA40-RS2 Interfaces

KNX

Serial RS232

Serial RS485

Network functions

Integration KNX

2000 DP

Integration M-Bus

250 DP

800 DP

2000 DP

Integration Modbus

250 DP

800 DP

2000 DP

Integration SCL

250 DP

800 DP

1000 DP

Option modules are "hot-pluggable"

Functions

Type summary

• The system controllers support the integration of Desigo RXB/RXL room controllers as well as third-party devices and systems via KNX, Modbus or MBus etc. in the automation level using BACnet/LonTalk or BACnet/IP

• Mapping and monitoring of third-party disciplines as HVAC, light, SPS etc.

• Functionality as freely programmable system controllers for standard or

proprietary protocol applications

• The system controllers provide the infrastructure to hold and execute the system and application specific functions. They are freely programmable.

• Comprehensive management and system functions are available:

− Alarm management

− Time scheduling

− Trends

− Access protection

Equipment combinations

System-Controller for the integration of KNX, M-Bus, Modbus

SCL: up to 1000 data points,

PXA40-RS2

PXA40-… option modules can be plugged and unplugged when the automation station is operating.

• The functionality is available immediately after inserting.

• The functionality disappears approx.1 minute after unplugging.

2 / 10

Siemens PXC001 System controllers CM1N9223en_01 Building Technologies 2014-04-04

Page 3

Ordering

Plastic housing

2a 2b

Front cover PXM40-RS... option module

Plug-in screw terminal block (operating voltage)

Plug-in screw terminal block (LONWORKS bus, PXC001.D only)

Network interface RJ45 (BACnet / IP, PXC001-E.D only)

LED indicators for communication

LED indicators for device and system status

Service pin (Network identification)

RJ45 Interface for operator unit and tool (RJ45, PXC001.D only)

Plug-in screw terminal block (RS485)

RS232 interface

Plug-in screw terminal block (KNX)

RJ45 interface (ETS tool for service use)

KNX programming pin

RJ45 interface for operator unit or PX KNX tool

Slider for mounting on DIN rail

RX TX

SERVICE

RX TX

RS232/RS485

KNX

SERVICE

INFO

COMM

LOW BATT

FAULT

RUN

HMI/TOOL

HMI

CLB

CLA

1 2

678

RS485

RS232

9 10

CE -

SERVICE

KNX

TOOL

CE +

9223z16

Product number

Stock number

Designation

PXC001.D

S55372-C113

System controllers ( BACnet/LonTalk)

PXC001-E.D

S55372-C114

System controllers (BACnet/IP)

PXA40-RS1

S55372-C115

Option module RS1

PXA40-RS2

S55372-C116

Option module RS2

PXC001...

Mechanical design

The compact construction enables the devices to be mounted on a standard mounting rail.

PXA40-RS...

Siemens PXC001 System controllers CM1N9223en_01 Building Technologies 2014-04-04

3 / 10

Page 4

The terminal blocks are removable for easy wiring.

LED

Color

Activity

Function

Continuously OFF

No power

Rapid flashing

Firmware missing / corrupt

BATT

Continuously ON

Battery empty– replace!

Flashing

Communication

INFO

Red

Freely programmable

command

21s

5 Hz 5 Hz

9222z02

Terminal blocks

LED indicators

Service pin

Communication

RS232/RS485: RX (Green) : TX (Yellow) KNX: RX (Green) TX (Yellow) Service (Red)

The other LEDs have the following meaning:

Service pin

RUN

FAULT

LOW

COMM

SERVICE (Ethernet, PXC001E.D)

SERVICE (LonTalk, PXC001.D)

Green Continuously ON

Red Continuously OFF

Continuously ON

Red Continuously OFF

Red Continuously ON

Continuously OFF

Red Continuously OFF

Continuously ON Flashing Flashing per wink command *)

Red Continuously OFF

Continuously ON

Flashing Flashing per wink

command *)

Power OK

OK Fault

Battery OK

Connection to switch OK No connection to switch

OK No connection to switch No IP address configured Physical identification of system controller after receipt of wink

ONWORKS node is configured

Faulty L

ONWORKS chip, or service pin

currently depressed

ONWORKS node is not configured

L Physical identification of system

controller after receipt of wink

Wink command pattern:

Identification of the system controller in the IP network or L

ONWORKS network

See "Commissioning".

Engineering

See the PX open documents in folder CM110761.

4 / 10

Siemens PXC001 System controllers CM1N9223en_01 Building Technologies 2014-04-04

Page 5

Mounting

Load plant operating program

Setting parameters and configurations

Wiring test

Network connection

Download

Restart

Commissioning

Force Firmware

The devices can be snapped onto standardized rails.

The power supply, LonTalk, RS485 and KNX connections have plug-in screw terminal blocks. The other interfaces are quick plug-in connections.

Instead of the front cover a PXA40-RS... option module can be fitted on the device.

In order to prevent equipment damage and/or personal injuries always follow local safety regulations and the required safety standards.

The plant operating program is downloaded using the CFC from XWP – locally via the automation station's RJ45 interface or via the network (BACnet/IP or BACnet/LonTalk).

Use the PX Design tool in XWP for setting the control parameters and the configuration data. Data visible on the network may also be edited with an operator unit PXM20 / PXM20-E (BACnet / LonTalk or BACnet / IP).

Part of the data can also be edited locally using the operator unit PXM10 (not available for PX KNX).

Use the Point Test Tool.

The network addresses are configured with XWP. For unique identification in the network (BACnet/IP or BACnet/LonTalk), press the Service button with a long, pointed object or send a wink command to the appropriate system controller (service LED blinks).

• Variant via V24: If the Force Firmware Download Key is pressed for approx. 10 s during a restart (reset), the current D-MAP program is deleted from the FLASH. The system controller waits briefly for the signal to activate the FWLoader and then starts the system controller.

• IP variant: (for PXC001-E.D, significantly faster than via V24) Press the Force Firmware Download key for 5 seconds (without hitting the reset button).

Prerequisite: A node setup of the controller has been conducted and no application is loaded or it was deleted in the CFC by clear/reset (communication settings remain – which would not be the case when restart erasing by pressing the reset key).

Siemens PXC001 System controllers CM1N9223en_01 Building Technologies 2014-04-04

For details see the Firmware Download Tool User's guide, CM110626.

Press the Reset button to force a restart

5 / 10

Page 6

Disposal: Seal battery terminals with tape.

Service

Lithium

Position of

buttons and batteries

Note

Battery life

Replacing the battery

STOP

Firmware upgrades

Maintenance

Caution!

The KNX programming pin is situated next to the KNX terminal block and the KNX tool plug

The real time clock is backed by a lithium battery type CR2032

• Life span without charge: min. 10 years.

• Life span with battery operation (cumulative): up to 1 month.

• After the "Battery low" event

the remaining life span under load is several

days.

The trend data and the actual parameters stored in the SDRAM memory are backed by a Lithium battery type FR6/AA AA.

• Life span without charge: min. 10 years.

• Life span with battery operation (cumulative): up to 1 month.

• After the "Battery low" event

the remaining life span under load is approx.

15 hrs.

1) "Battery low" event: The "LOW BATT" LED lights up when one of the batteries' charge is low, and the automation station automatically sends a system event.

To change the battery, remove the front cover. The battery can be removed indefinitely as long as the unit has power. Insert new battery correctly (+ / –).

• Note the special disposal notes on Li batteries.

• A wrist-strap and grounding cable must be used to avoid hardware

damage through electrostatic discharge (ESD).

Firmware and operating system stored in non-volatile Flash ROM. Flash ROM memory can be easily updated on the plant, when a new firmware version is available.

Disposal

The devices are classified as waste electronic equipment in terms of the European Directive 2012/19/EU (WEEE) and should not be disposed of as unsorted municipal waste. The relevant national legal rules are to be adhered to. Regarding disposal, use the systems setup for collecting electronic waste. Observe all local and applicable laws. Lithium batteries: May catch fire, explode or leak. Do not short circuit, charge, disassemble, dispose of in fire, heat above 100°C, or expose to water.

6 / 10

Siemens PXC001 System controllers CM1N9223en_01 Building Technologies 2014-04-04

Page 7

Technical data

General device data

Operating voltage

AC 24 V ± 20%

Rated voltage

AC 24 V

Safety extra-low voltage SELV or Extra-low voltage PELV

HD 384 Operating frequency

50/60 Hz

Energy consumption

Max. 3.5 VA

External fusing (compulsory)

External fuse protection for secondary current: Slow blow fusible link Max. 10 circuit breaker Max. 13 A type C, or transformer with secondary current limitation of max. 10 A

Operating data

Processor

Motorola Power PC MPC885

Storage

64MB SDRAM / 32MB FLASH (96MB total)

Data backup in event of power failure

Battery Backup of realtime clock Lithium CR2032 (field replaceable)

Battery operation (cumulative): 1 month Without load: 10 years

Battery backup for SDRAM 1 x FR6/AA Lithium (field replaceable)

Battery operation (cumulative): 1 month Without load: 10 years

Interfaces, communication

Building Level Network

LonWorks FT5000 Transceiver

BACnet on UDP/IP

(RJ45, shielded)

Local Communication

• PXM10 (RS232)

Tool (RJ45)

-Local Communication (HMI)

• PXM10 (RS232)

• PXM20 (BACnet/LonTalk) (RJ45)

• PXM10 (RS232)

One PXM10 operator unit and one

type.

One PXM10 on RJ45

KNX Tool-Interface

RJ45

CE+, CE–

KNX bus

Interface type

KNX (electrically isolated)

Transceiver

TP-UART

Bus current

5 mA

Baud rate

9.6 kbit/s

Bus topology, bus termination

Refer to KNX manual

RS232 interface

Baud rate

300, 600, 1200, 2400, 4800, 9600,

(depends on software)

Data bits

7 or 8 (depending on software)

Stop bits

1 or 2 (depending on software)

Parity

None, even or odd

(depending on software)

Flow control

Xon/Xoff, hardware or none

(depending on software)

Cable length

9-core standard screened cable Max. 3 m

PXC001.D PXC001-E.D

(HMI, Tool)

Twisted Pair, 78 kBit/s (Screw terminals)

• PXM20 (BACnet/LonTalk, RJ45)

•

PXM20 per system controller may be connected. But not twice the same

IEEE802.3, Auto-sensing 10 Base-T / 100 Base-TX

19200, 38400

Siemens PXC001 System controllers CM1N9223en_01 Building Technologies 2014-04-04

7 / 10

Page 8

RS485 interface

Interface type

RS485, (electrically isolated)

Baud rate, data bits / stop bit(s), parity

As for RS232 (depends on software)

Cable length

Standard RS bus cable Max. 1200 m

Plug-in screw terminal

Solid or stranded conductors

0.25…2.5 mm2 or 2 x 1.5 mm2

Simple cable lengths, cable types

Connection cable Ethernet and PXM20-E

Max. 100 m

Cable type

Standard at least CAT5 UTP (Unshielded Twisted Pair) or STP (Shielded Twisted Pair)

Connection cable LONWORKS bus

See Installation Guide CA110396

Cable type

CAT5

Housing protection standard

Protection standard

IP 20 to IEC 60529

Protection class

III to EN 60730

Ambient conditions

Normal operation

To IEC 60721-3-3

Environmental conditions

Class 3K5

Temperature

0...50 °C

Humidity

5…95 % r.h. (non-condensing)

Mechanical conditions

Class 3M2

Transport

To IEC 60721-3-2

Environmental conditions

Class 2K3

Temperature

-25…70 °C

Humidity

5…95 % r.h. (non-condensing)

Mechanical conditions

Class 2M2

Standards, directives and approvals

Product standard

EN 60730-1

CM1T9223xx

CM1T922

Zertifikat

AMEV: Supports profiles AS-A and AS-B to

buildings"

BACnet 2011, V1.1 http://database.ul.com/

Document download

www.hqs.sbt.siemens.com/gip/general/dlc/dl c_mobile_direct.asp?BPZ:PXC001

Environmental compatibility

The product environmental declaration

environmental benefit, disposal)

ISO 14001 (Environment) ISO 9001 (Quality)

Dimensions

See “Dimensions”

Weight

Without / with packaging

PXA-40-RS1, PXA40-RS2

0.635 kg / 0.731 kg

0.048 kg / 0.060 kg

2en_C1

AMEV directive "BACnet in public

CM1E9223 contains data on environmentally compatible product design and assessments (RoHS compliance, materials composition, packaging,

PXC001.D, PXC001-E.D

8 / 10

Siemens PXC001 System controllers CM1N9223en_01 Building Technologies 2014-04-04

Page 9

Pin assignment

9222z12

8 7 6 5 4 3 2 1

4. Not used

8. Not used

9215Z01

8 7 6 5 4 3 2 1

4. G/Plus

8. COM1/RxD

9215Z01

8 7 6 5 4 3 2 1

1. LONW

Data A (CLA)

4. G / Plus

8. COM1 / RxD

9280Z03

8 76 5 4 3 21

4. Not used

8. Not used

9281z04

1 2 3 4 5

6 7 8 9

DCD

Data carrier detect

DSR

Data set ready

RXD

Received data

RTS

Request to send

TXD

Transmit data

CTS

Clear to send

DTR

Data terminal ready

Not connected

GND

Signal ground

1 2

CLB

CLA

9 10

Supply plug

(PXC001.D)

(PXC001-E.D)

Plug "HMI" and

(PXC001.D)

Tool plug (KNX)

RS232 plug serial

RS485 plug

KNX plug

LONWORKS plug

Ethernet plug

"HMI" plug

Plug-in screw terminal block

1 AC 24 V 2 Ground 3 Functional earth

Plug-in screw terminal block

4 CLA LonWorks Data A 5 CLB LonWorks Data B

RJ45 socket screened, standard connection in accordance with AT&T256

1. Tx+

2. Tx –

3. Rx +

5. Not used

6. Rx –

7. Not used

1. Unoccupied

2. Unoccupied

3. G0, GND

5. Not used

6. Not used

7. COM1/TxD

"HMI/Tool"

ORKS

2. LONWORKS Data B (CLB)

3. G0 / GND

5. Not used

6. Not used

7. COM1 / TxD

1. KNX data (CE+)

2. KNX data (CE–)

3. Not used

5. Not used

6. Not used

7. Not used

Plug-in screw terminal block 6 + Tx 7 – Rx 8  Screen, connected to functional earth

Siemens PXC001 System controllers CM1N9223en_01 Building Technologies 2014-04-04

Plug-in screw terminal block

9 (CE–) – KNX data cable 10 (CE+) + KNX data cable

9 / 10

Page 10

Dimensions

50.2

143

38.5

50.8

256

271.5

133,5

149.4

44.3

32.5

9223M01

All dimensions in mm

 2014 Siemens Switzerland Ltd Subject to change

10 / 10

Siemens PXC001 System controllers CM1N9223en_01 Building Technologies 2014-04-04