Siemens Delta Series, 5WG1 585-2AB01, 5WG1 585-2AB21, 5WG1 585-2AB11, 5WG1 584-2AB71 Technical Product Information

GAMMA instabus

Technical Product Information

March 2008

DELTA profil Display and control unit UP 585 5WG1 585-2AB_1 DELTA style Display and control unit UP 584 5WG1 584-2AB_1 DELTA ambiente Display and control unit UP 586 5WG1 586-2AB_1

Product DELTA profil DELTA style DELTA ambiente

Display and control unit

Frames

Intermediate frames ---

5WG1 585-2AB01 pearl grey 5WG1 585-2AB11 titanium white 5WG1 585-2AB21 anthracite 5WG1 585-2AB71 silver

cut out frames --- ---

5WG1 585-2AB11 titanium white 5WG1 584-2AB21 basalt black 5WG1 584-2AB41 platinum metallic

ordered separately from the DELTA ranges

5TG1 328 titanium white 5TG1 368 basalt black 5TG1 328-1 platinum metallic

5WG1 586-2AB01 arctic white

---

B1 Driver with bus connection *) B2 Frame B3 Intermediate frame (only for DELTA style) B4 Display unit *) B5 Fixing screw *) B6 Blende *)

*) Lieferumfang

B6

B1

B2

B3

B4

B5

Diagram 1: Installation of the display unit

Product and Applications Description

The display unit is used to indicate freely programmable messages. A message generally consists of read-only text and placeholders. The display unit can be freely configured with different fonts, characters and symbols. Depending on the parameter settings, it is possible to assign alarm functions to the messages. The display is carried out via a graphical LC display. If Arial font is used in 12 pt, 5 lines can be displayed. The LC display contains green/yellow backlighting which can be switched on and off via software. The output of an alarm tone can also be set.

The various messages can be selected by pressing the two push buttons on the display unit. It is also possible to operate selectable bus functions with two further push buttons. The display unit is placed on the bus driver module together with the relevant frame. It can only function in connection with this bus driver module and an appropriate application program i.e. the display unit consists of the device [hardware] and the application program [software]. The frames are not included with supply and must be ordered separately. The intermediate frame should be used for DELTA style.

Siemens AG UP 58x, 6 pages Technical Manual Automation and Drives Group Electrical Installation Technology © Siemens AG 2008 Update: http://www.siemens.com/gamma P.O. Box 10 09 53, D-93009 Regensburg Subject to change without prior notice

2.3.1.2/1

GAMMA instabus

Technical Product Information

March 2008

DELTA profil Display and control unit UP 585 5WG1 585-2AB_1 DELTA style Display and control unit UP 584 5WG1 584-2AB_1 DELTA ambiente Display and control unit UP 586 5WG1 586-2AB_1

With the help of ETS, the application programs can be selected and the specific parameters and addresses can be assigned.

Application programs

01 07 Graphical display unit 801501 (for ETS2 version 1.2 or later) 01 07 Graphical display unit 801502 (for ETS3 version 1.0 or later)

• The graphical display unit can indicate up to 16 dif- ferent messages about the states of bus devices using various fonts or symbols and can also actively modify these states.

• The display unit has backlighting as well as a buzzer. Both the backlighting and the buzzer can be set, optionally active or passive mode.

• In the event of an alarm, a signal is sent on the bus and the selected message simultaneously flashes in the centre of the display unit (the frequency can be set).

Note: The application programs can be used only with ETS2 version 1.2 or later versions of the ETS.

Installation instructions

• The device can be used for fixed installations, in dry interior spaces and for integration into a flush socket.

DANGER

V

• The device may only be installed and commissioned by an authorized electrician.

• The device may not be inserted in the same box as 230 V devices.

• The device may be used in switch sockets, if VDE approved devices have been used.

• The prevailing safety and accident regulations must be observed.

• The device may not be opened.

• For planning and construction of electric installations,

the relevant guidelines, regulations and standards of the respective country are to be considered.

Technical data

Power supply

• via the bus line

Operating elements

• 2 push buttons for operating the display function

• 2 push buttons for operating the selectable bus func-

tions

• 1 learning button under the cover for toggling be- tween normal mode / addressing mode

Display elements

• LC display (contains green/yellow backlighting which can be switched on and off via software)

• 1 red LED for checking the bus voltage and for dis- playing normal mode / addressing mode

Number of messages

• 16 (freely selectable)

Number of characters per message

• up to 30 characters per line depending on the font

• up to 3 lines

Alarm functions

• priority display of alarm messages

• optical display (flashing)

• acoustic signal (signal tone)

• acoustic feedback via push button action

Connections

• KNX/EIB bus terminal

Mechanical data

• Housing: plastic

• Dimensions (L x W x D):

- Display unit UP 584, UP 585, UP 586:

65 x 65 x 20 mm (without spring) 65 x 65 x 33 mm (including spring)

- Driver: 71 x 71 x 16 mm

• Weight: approx. 100 g

• Fire load: approx. 1500 kJ ± 10 %

• Installation: The display unit is mounted on the rele-

vant bus driver module. It cannot be plugged onto the standard type of bus coupler and no other operator interfaces can be operated on the driver.

Technical Manual UP 58x, 6 pages Siemens AG Automation and Drives Group Update: http://www.siemens.com/gamma © Siemens AG 2008 Electrical Installation Technology Subject to change without prior notice P.O. Box 10 09 53, D-93009 Regensburg

2.3.1.2/2

GAMMA instabus

A1 A3 A

Technical Product Information

March 2008

DELTA profil Display and control unit UP 585 5WG1 585-2AB_1 DELTA style Display and control unit UP 584 5WG1 584-2AB_1 DELTA ambiente Display and control unit UP 586 5WG1 586-2AB_1

Electrical safety

• Degree of pollution (according to IEC 60664-1): 2

• Type of protection (according to EN 60529): IP 20

• Protection class (according to IEC 61140): III

• Overvoltage category (according to IEC 60664-1): III

• Bus: safety extra-low voltage SELV DC 24 V

• Device complies with EN 50090-2-2 and IEC 60664-1

EMC requirements

• complies with EN 50081-1, EN 50090-2-2 and EN 61000-6-2

Environmental conditions

• Climatic withstand capability: EN 50090-2-2

• Ambient operating temperature: - 5 ... + 45 °C

• Storage temperature: - 25 ... + 70 °C

• Relative humidity [not condensing): 5 % to 93 %

Reliability

• Rate of failure: 572 fit

Markings

• KNX EIB

CE mark

• In accordance with the EMC guideline (residential and functional buildings) and the low voltage guideline

Location and function of the operating elements

2

Diagram 2: Location of the display and operating ele-

ments

A1 LC display (LCD) for indicating the messages A2 Push buttons for scrolling through the lines

(UP / DOWN)

A3 Push buttons for controlling the selectable bus

functions

Installation of the driver

General description The display unit is placed on the driver together with the relevant frame. The driver with bus connection is inserted in boxes of 60 mm ∅ using screw fixing. The connection to the bus line is carried out via plug-in screwless terminals for single-core conductors.

The driver with bus connection should be mounted so that the interface is located at the bottom (Diagram 3). This ensures that the display unit that is connected to the interface is mounted in the correct operational position.

Diagram 3: Installation of the driver with bus

C1 Installation box (60 mm Ø according to DIN 49073)

C2 Slots for fixing C3 Driver with bus connection C4 Interface C5 Fixing screws

Bus terminal The bus terminal (D2) is located at the rear of the driver.

C2 C3

C4 C5

connection

(Diagram 4)

C1

Siemens AG UP 58x, 6 pages Technical Manual Automation and Drives Group Electrical Installation Technology © Siemens AG 2008 Update: http://www.siemens.com/gamma P.O. Box 10 09 53, D-93009 Regensburg Subject to change without prior notice

2.3.1.2/3

GAMMA instabus

Technical Product Information

March 2008

DELTA profil Display and control unit UP 585 5WG1 585-2AB_1 DELTA style Display and control unit UP 584 5WG1 584-2AB_1 DELTA ambiente Display and control unit UP 586 5WG1 586-2AB_1

Connecting the bus cable

(Diagram 4)

− The bus terminal (D2) is suitable for single-core con- ductors with 0.6 ... 0.8 mm Ø.

− The bus terminal (terminal block) (D2) consists of two components (D2.1, D2.2), each with four terminal contacts, Diagram 7.

− Strip the insulation from the conductor (D3) and place in the terminal (D2) (red = +, grey = -).

Diagram 4: Connecting the bus cable

Installation of the display

B1

B2

B3

B4

B5

B6

B1 Driver with bus connection B2 Frames B3 Intermediate frame (only for DELTA style) B4 Display unit B5 Screws for fixing the display unit onto the

driver B1

B6 Cover

- Place the display unit (B4) with B6 and the relevant

frame (B2) onto the driver (B1).

- Remove the cover (B6) from the display unit as de-

scribed under ‘Dismantling’ in order to program the physical address.

- Secure the display unit (B4) with the two screws (B5).

- Now program the physical address.

The location of the programming button and the programming LED is indicated in Diagram 5.

- Remove the protective film from the LC display,

Diagram 6c.

- Place the cover (B6) on the display unit again (B4).

Location of the programming button and programming LED

Programming LED

Programming- button

Diagram 5: Location of the programming button and LED

is also indicated on a non-configured LCD if bus voltage has been applied

Dismantling

- Remove the cover as described in Diagram 6a or 6b.

Caution:

Do not touch any components apart from the programming button (Diagram 6) as damage could otherwise be caused.

- Loosen the fixing screws (B5).

- Place the cover (B6) back on the display unit (B4).

- Remove the frame (B2) together with the display unit

- Loosen the screws of the driver in the flush-type box

- Separate the bus driver module from the bus cable

from the driver.

(Diagram 3).

(Diagram 7).

Technical Manual UP 58x, 6 pages Siemens AG Automation and Drives Group Update: http://www.siemens.com/gamma © Siemens AG 2008 Electrical Installation Technology Subject to change without prior notice P.O. Box 10 09 53, D-93009 Regensburg

2.3.1.2/4

GAMMA instabus

Technical Product Information

March 2008

DELTA profil Display and control unit UP 585 5WG1 585-2AB_1 DELTA style Display and control unit UP 584 5WG1 584-2AB_1 DELTA ambiente Display and control unit UP 586 5WG1 586-2AB_1

Removing the cover

(Diagram 6a and 6b)

Variant 1: Gently press the sides of the cover together

and tilt.

Abziehen der Abdeckung

Diagram 6a: Variant 1

Variant 2: The cover has an opening at the top in the

centre for removal. Place the screwdriver at the opening and lift the top of the cover forwards with the screwdriver.

Diagram 6b: Variant 2

Diagram 6c: Removing the protective film

Removing/inserting the bus terminal (Diagram 7)

− To remove the bus terminal, carefully insert the screwdriver in the wire entry slot in the grey section of the bus terminal (D2.2) and pull the bus terminal (D2) out of the driver (D1).

− To insert the bus terminal, place the bus terminal (D2) in the guide slot of the driver with bus connection (D1) and press the bus terminal (D2) downwards until it reaches the stop.

Do not jumper bus connections as there is a

Note:

danger of shorting the device.

D 2

D 2.3

D 2.2

D 2.1

D 1

Diagram 7: Removing the bus terminal

Disconnecting the bus cable

(Diagram 8)

− Remove the bus terminal (D2) as shown in Diagram 8 and pull out the conductor (D3) of the bus cable by simultaneously rotating backwards and forwards.

D2

D3

Diagram 8: Disconnecting the bus cables

Siemens AG UP 58x, 6 pages Technical Manual Automation and Drives Group Electrical Installation Technology © Siemens AG 2008 Update: http://www.siemens.com/gamma P.O. Box 10 09 53, D-93009 Regensburg Subject to change without prior notice

2.3.1.2/5

GAMMA instabus

Technical Product Information

March 2008

DELTA profil Display and control unit UP 585 5WG1 585-2AB_1 DELTA style Display and control unit UP 584 5WG1 584-2AB_1 DELTA ambiente Display and control unit UP 586 5WG1 586-2AB_1

Dimension Driver

Dimensions in mm

71

Dimension Display unit

Dimensions in mm

65

71

20

16

33

General Notes

• The operating instructions must be handed over to the client.

• Any faulty device should be returned to the local Siemens office.

• If you have further questions concerning the product please contact our technical support:

! +49 (180) 5050-222 ! +49 (180) 5050-223 " www.siemens.com/automation/support-request

Technical Manual UP 58x, 6 pages Siemens AG Automation and Drives Group Update: http://www.siemens.com/gamma © Siemens AG 2008 Electrical Installation Technology Subject to change without prior notice P.O. Box 10 09 53, D-93009 Regensburg

2.3.1.2/6