Shuttle SZ68R5 User guide
SZ68R5 Quick Guide
62R-SZ68R0-1501
English.Spanish.Korean.
Traditional Chinese.Japanese.
French. German Quick Guide
【
Front Panel
F1. 5.25” Bay
F6
F3
F4
F5
F2. 3.5” Bay
F3.
F4.
F5. Power Switch & Power LED
F6. HDD LED
F7. USB3.0 Ports
F8. USB2.0 Port
F9. Mic In
F10. Headphone
F11.
F1
F2
English
】
Eject Button
Open Door
USB2.0 Port & Fast Charger
Jumper Settings
J1
S/PDIF OutPut Connector
1=Ground
2=VCC
3=SPDIFO
J3
COM Header (COM1)
1=DCD 2=RXD
3=TXD 4=
5=Ground 6=DSR
7=RTS 8=CTS
9=Ring 10=NA
9 7 5 3 1
1 2 3
DTR
(JP2)
J2
CIR Header (JP6)
1=5V
2=NA
3=Ground
4=GPIO1
5=GPIO2
J4
Power Header (JP3)
1=+HD_LED 2=PWR_LED
3=-HD_LED 4=
5=RST_SW 6=PWR_SW
7=GND 8=GND
9=NULL 10=NA
9 7 5 3 1
1 2 3 4 5
GND
A. Begin Installation
For safety reasons, please ensure that the power cord is
disconnected before opening the case.
1. Unscrew 3 thumbscrews of the chassis cover.
2. Slide the cover backwards and upwards.
2
1
3. Unfasten the rack mount screws and remove the rack.
Please do not apply excess amount of thermal paste.
9. Tear off the protective membrane from the bottom of ICE module.
Remove the protective socket mylar from the CPU socket.
10. Screw the ICE module to the mainboard. Note to press down on the
opposite diagonal corner while tightening each screw.
11. Connect the fan connector.
Fan Connector
12. Fasten the Smart Fan
to the chassis with the
4 thumbscrews.
D. Mini PCIe card Installation
1. Install the Mini PCIe card into the Mini PCIe slot /
with screws.
E. Peripheral Installation
1. Loosen the purse lock and separate the Serial ATA and power cables.
2. Place the HDD and optical drive in the rack and secure with screws
from the side.
Serial ATA Optical Drive
Serial ATA HDD
3. Place the rack in the chassis and refasten the rack.
mSATA Slot
and affix it
F7
F8 F9
B15
B1
B2
B3
B6
B4
B5
Front Speaker Out
Center/Subwoofer Speaker Out Port
Front Audio Header-JP5
J10
J7
USB Header-USB1,USB2
J6
CPU FAN Connector-FAN2
/ Line-In Ports
Side Speaker Out
/Real Speaker Out
One PCIe x4 Slot
One PCIe x16 Slot
B7
F11
F10
Back Panel
B1. AC Power Socket
B2. Serial Port (Optional)
B3. S/PDIF Out Port
B4. DVI-I Port
B5. HDMI Port
B6. eSATA & USB2.0 Ports
B7. USB3.0 Ports
B8. Clear CMOS Button
B9. Front Speaker Out (L/R) Port
B10. Side Speaker Out (L/R) Port
B11. Real Speaker Out (L/R) Port
B12. Center/Subwoofer
Speaker Out Port
B13.
Line-In Port
B14. LAN & USB2.0 Ports
B15. Wireless LAN Perforation
(Optional)
B14
B8
B15
B13
B9
B15
B12
B11
B10
DVI-I & HDMI Ports cannot be used, if the
PCIe x16 graphics card is installed.
Motherboard Illustration
/
Clear CMOS Button
2x USB 2.0 Ports &1x LAN
HDMI Port & DVI-I Port
2x USB 2.0 Ports & eSATA
Port
2x USB 3.0 Ports
AUX_IN Connector-CN1
S/PDIF OutPut Connector
USB Header-USB3
Intel® Z68 Chipset
J7
J5
J1
10 8 6 4 2
J5
AUX IN Connector (CN1)
1=AUX-IN – Left
2=Ground
3=Ground
4=AUX-IN – Right
4 3 2 1
J7
USB Header (USB1,USB2,USB3)
1=5V_USB 2=5V_USB
3=USB A- 4=USB B5=USB A+ 6=USB B+
7=GND 8=GND
9=NA 10=NULL
J8
LPC Header (JP1)
1=+12V 2=5V
5=CLK_48M 6=
9=LAD3 10=LAD2
13=Ring 14=LDRQ0
17=LAD0 18=+3.3V
11 12 13 14 15 16 17 18 19 20
1 2 3 4 5 6 7 8 9 10
J9
USB 3.0 Header (JP4)
1=5VCC 2=A_RX_N
5=A_TX_N 6=
9=A_Data_P 10=OC
13=Ground 14=B_TX_P
17=B_RX_P 18=B_RX_N
11 12 13 14 15 16 17 18 19 20
1 2 3 4 5 6 7 8 9 10
J10
Front Audio Header (JP5)
1=MIC_L 2=GND
3=MIC_R 4=Front_Detect
5=LINE_R 6=Mic_detect
7=sense 8=NA
9=LINE_L 10=Line_Detect
CLK_33M
A_TX_P
10 8 6 4 2
J6
CPU Fan Connectors
SPEED_SENSE
PWM_CTRL
FAN1/ FAN2
9 7 5 3 1
10 8 6 4 2
3=5VSB 4=SERIRQ
7=SIO_RST 8=
11=-12V 12=3VSB
15=SIO_PME 16=LAD1
19=GND 20=NA
3=A_RX_P 4=Ground
7=Ground 8=
11=B_Data_P 12=B_Data_N
15=B_TX_N 16=Ground
19=5VCC 20=NA
9 7 5 3 1
10 8 6 4 2
+12V
LFRAME
A_Data_N
Ground
B. CPU and ICE Installation
1. Unfasten the ICE fan thumbscrews on the back of the chassis.
2. Unfasten the four ICE module attachment screws and unplug the fan
connector.
Fan Connector
3. Remove the ICE module from the chassis and put it aside.
This 1155 pin socket is fragile and easily damaged. Always use
extreme care when installing a CPU and limit the number of times
that you remove or change the CPU. Before installing the CPU,
make sure to turn off the computer and unplug the power cord
from the power outlet to prevent damage to the CPU.
Follow the steps below to correctly install the CPU into the
motherboard CPU socket.
A
4. First unlock. Press
released from the retention tab and raise the socket lever.
A
5. Lift the metal load plate on the CPU socket.
Remove the
protective
membrane
DO NOT touch socket contacts. To protect the CPU socket, always
replace the protective socket cover when the CPU is not installed.
6. Orientate the CPU and socket, you may align the CPU notches with the
socket alignment keys. Make sure the CPU is perfectly horizontal, insert
the CPU into the socket.
Triangle Pin1
Marking
on the CPU
with your thumb, then move it to B until it is
B
Socket 1155
CPU
Metal load plate
C. Memory module Installation
Guidelines for Memory Conguration
Before installing DIMMs, read and follow these guidelines for memory
configuration.
Make sure that the motherboard supports the memory.
It is recommended that memory of the same capacity, brand,
speed,and chips are used.
(Go to Shuttle's website for the latest memory support list.)
Memory modules have a foolproof design. A memory module can
be installed in only one direction. If you are unable to insert the
memory, switch the direction.
Dual-Channel mode Population Rule
In Dual-Channel mode, the memory modules can transmit and receive
data with two data bus lines simultaneously. Enabling Dual-Channel
mode can enhance the system performance. The following illustrations
explain the population rules for Dual-Channel mode.
A
DIMM1 (Red),Empty
DIMM2 (Yellow),Installed
DIMM3 (Red),Empty
DIMM4 (Yellow),Installed
B
DIMM1 (Red),Installed
DIMM2 (Yellow),Installed
DIMM3 (Red),Installed
DIMM4 (Yellow),Installed
Installing a memory module
DDR3 DIMMs are not compatible to each other or DDR DIMMs.
Be sure to install DDR3 DIMMs on this motherboard. Follow the steps below
to correctly install your memory modules in the memory sockets.
1. Unlock the DIMM latch.
2. Align the memory module's cutout with the DIMM slot notch.
Slide the memory module into the DIMM slot.
A DDR3 memory module has a cutout, so it can only fit in one direction.
1
DDR3 240-pin 1.5V
72*2=144 pin
Latch
2
48*2=96 pin
Cutout
Notch
Latch
3
Connect the Serial ATA Cable
4. Connect the Serial ATA and power cables to the HDD.
5. Connect the Serial ATA and power cables to the optical drive.
to motherboard.
Serial ATA Power Cable
Serial ATA Cable
Serial ATA Power Cable
Serial ATA Cable
F. Accessories Installation
1. Unfasten expansion slot bracket screws.
Remove the back panel bracket and put the bracket aside.
The maximum size acceptable for display cards is
267mm x 98mm x 34.6mm.
PCIe x 4 slot
PCIe x16 slot
2. Install the PCIe x4 and PCIe x16 card into the PCIe x4 and PCIe x16 slots.
3. Secure the bracket.
VGA Card PCB
5mm
34.6mm
Chassis
Cover
PCIe x16 / PCIe x 4 slots
G. Complete
SATA 3.0 Connector -1,2
J9
USB3.0 Header-JP4
LPC Header-JP1
J8
CPU FAN Connector-FAN1
J6
J3
COM Header-COM1
SATA 2.0 Connector - 3,4
J4
Power Header-JP3
J2
Mini PCIe Slot
mSATA Slot
CIR Header-JP6
LGA 1155
ATX Power Connector-ATX1
4x 240 pins DDR3
DIMM Slots
ATX Power Connector-PWR1
Safety Information
Read the following precautions before setting up a Shuttle XPC.
CAUTION
Incorrectly replacing the battery may damage this computer.
Replace only with the same or equivalent as recommended by Shuttle.
Disposal of used batteries according to the manufacturer's instructions.
Laser compliance statement
The optical disc drive in this PC is a laser product.
The drive's classication label is located on the drive.
CLASS 1 LASER PRODUCT
CAUTION： INVISIBLE LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM.
Please be aware of the CPU orientation, DO NOT force the CPU into the
socket to avoid bending of pins on the socket and damage of CPU!
7. Close the metal load plate, lower the CPU socket lever and lock in place.
8. Spread thermal paste evenly on the CPU surface.
Thermal Paste
application area
The product’s colour and specification will depend on the actual shipping product.
L
3. Check that the latches are closed, and the memory module is firmly installed.
Repeat the above steps to install additional memory modules,
if required.
1. Replace the cover and refasten the thumbscrews.
2. Complete.
Please press "Del" key while booting to enter BIOS and load the
optimised BIOS settings.
53R-SZ68R3-3001
Loading...