Shuttle SH67H3 Quick Start Manual
SH67H3 Quick Guide
Front Panel
F1
F2
F4
F5
F6
F7
F8
F3
F9
Back Panel
B1
B2
B3
B14
B4
B15 B14
B6B5
B7
B9
B13
B8
B12
B10
B11
DVI-I & HDMI Ports cannot be used, if the
PCI-e/ PCI Express graphics card is installed.
Motherboard Illustration
Front-Out/Line-In Ports
J3
Center/Bass/
Surround-Back/
Side Surround Ports
Clear CMOS Button
S/PDIF-Out-JP1
J1
AUX IN Connector
-AUX_IN1
FAN Connector-
J2
J2
CPU_FAN1
FAN Connector-
FAN1
One PCI Express x1
Intel H67 Chipset
Slot
【
English
F1. 5.25” Bay
F2. 3.5” Bay
F3. Power Switch
& Power LED
F4. HDD LED
F5. Reset
F6. Headphone
F7. Mic In
F8. USB3.0 Ports
F9. eSATA+USB2.0
Port
B1. AC Power Socket
B2. DVI-I Port
B3. HDMI Port
B4. USB3.0 Ports
B5. Esata & USB2.0 Ports
B6. LAN & USB2.0 Ports
B7. Line-In Port
B8. Center/Bass Port
B9. Front Out (L/R)
B10. Side Surr (L/R)
B11. Clear CMOS Button
B12. Surround Back
(L/R) Port
B13.
SPDIF Out Port
Wireless LAN
B14.
Perforation
B15. Serial Port
Perforation
2x USB 2.0 Ports
& 1x LAN1
2x USB 2.0 Ports
& Esata Port
HDMI Port &
DVI-I Port
2x USB 3.0 Ports
USB HeadersUSB1
】
J5
Jumper Settings
J1
S/PDIF Out connector
Pin Assignments (JP1):
1=GND
2=VCC
3=SPDIFO
J2
Fan Connectors
FAN_SENSE
FAN_PWM
CPU_FAN1
J3
AUX IN Connector
Pin Assignments (AUX_IN1):
1=CD_IN_L
2=Ground
3=Ground
4=CD_IN_R
J5
USB
Connector
Pin Assignments (USB1):
1=VCC 2=VCC
3=D1- 4=D05=D1+ 6=D0+
7=Ground 8=Ground
9=KEY 10=Ground
J6
Front Connector
Pin Assignments (JP3):
1=HDD_IED 2=Power_LED
3=HDD_IED- 4=
5=Reset_button 6=Power_button
7=Ground 8=Ground
9=NC 10=NA
J7
USB 3.0 Connector
Pin Assignments (CN5):
1=Wake- 2=-PCI-E RST 3=Ground 4=USB3_100M+
5=USB3_100M- 6=Ground 7=PET2P 8=PET2N
9=-Ground 10=PER2P 11=PER2N
12=Ground 13=VCC3 14=VCC3
J8
RS232 Header
Pin Assignments (COM1):
1=DCD1P 2=RX1P
3=TXD1P 4=DTR1P
5=Ground 6=DSR1P
7=RTS1P 8=CTS1P
9=-XRI 10=NA
+12V
Ground
4 3 2 1
Ground
FAN_SENSE
J4
CIR connector
Pin Assignments (JP6):
1=Ground
2=5V_DUAL
3=CIR-RX
1 2 3
+12V
FAN1
9 7 5 3 1
10 8 6 4 2
9 7 5 3 1
10 8 6 4 2
9 7 5 3 1
10 8 6 4 2
Ground
1 2 3
A. Begin Installation
For safety reasons, please ensure that the power cord is
disconnected before opening the case.
1. Unscrew 3 thumbscrews of the chassis cover.
2. Slide the cover backwards and upwards.
2
1
3. Unfasten the rack mount screws and remove the rack.
B. CPU and ICE Installation
1. Unfasten the ICE fan thumbscrews on the back of the chassis.
2. Unfasten the four ICE module attachment screws and unplug the fan
connector.
Fan Connector
3. Remove the ICE module from the chassis and put it aside.
This 1155 pin socket is fragile and easily damaged. Always use
extreme care when installing a CPU and limit the number of times
that you remove or change the CPU. Before installing the CPU,
make sure to turn off the computer and unplug the power cord
from the power outlet to prevent damage to the CPU.
Follow the steps below to correctly install the CPU into the
motherboard CPU socket.
A
4. First unlock. Press
released from the retention tab and raise the socket lever.
A
5. Lift the metal load plate on the CPU socket.
Remove the
protective
membrane
DO NOT touch socket contacts. To protect the CPU socket, always
replace the protective socket cover when the CPU is not installed.
6. Orientate the CPU and socket, you may align the CPU notches with the
socket alignment keys. Make sure the CPU is perfectly horizontal, insert
the CPU into the socket.
with your thumb, then move it to B until it is
B
Metal load plate
Metal load plate
Thermal Paste
application area
Retention tab
Load lever
Please do not apply excess amount of thermal paste.
9. Tear off the protective membrane from the bottom of ICE module.
Remove the protective socket mylar from the CPU socket.
10. Screw the ICE module to the mainboard. Note to press down on the
opposite diagonal corner while tightening each screw.
11. Connect the fan connector.
1
4
Fan Connector
12. Fasten the Smart Fan
to the chassis with the
4 thumbscrews.
3
2
C. Memory module Installation
Guidelines for Memory Conguration
Before installing DIMMs, read and follow these guidelines for memory
configuration.
Make sure that the motherboard supports the memory.
It is recommended that memory of the same capacity, brand,
speed,and chips are used.
(Go to Shuttle's website for the latest memory support list.)
Memory modules have a foolproof design. A memory module can
be installed in only one direction. If you are unable to insert the
memory, switch the direction.
Dual-Channel mode Population Rule
In Dual-Channel mode, the memory modules can transmit and receive
data with two data bus lines simultaneously. Enabling Dual-Channel
mode can enhance the system performance. The following illustrations
explain the population rules for Dual-Channel mode.
A
DIMM1 (Red),Empty
DIMM2 (Yellow),Installed
DIMM3 (Red),Empty
DIMM4 (Yellow),Installed
B
DIMM1 (Red),Installed
DIMM2 (Yellow),Installed
DIMM3 (Red),Installed
DIMM4 (Yellow),Installed
Installing a memory module
DDR3 DIMMs are not compatible to each other or DDR DIMMs.
Be sure to install DDR3 DIMMs on this motherboard. Follow the steps below
to correctly install your memory modules in the memory sockets.
1. Unlock the DIMM latch.
2. Align the memory module's cutout with the DIMM slot notch.
Slide the memory module into the DIMM slot.
A DDR3 memory module has a cutout, so it can only fit in one direction.
1
DDR3 240-pin 1.5V
Latch
Cutout
Notch
Latch
D. Peripheral Installation
1. Loosen the purse lock and separate the Serial ATA and power cables.
2. Place the HDD and optical drive in the rack and secure with screws
from the side.
Serial ATA Optical Drive
Serial ATA HDD
3. Place the rack in the chassis and refasten the rack.
4. Connect the Serial ATA and power cables to the HDD.
Serial ATA Cable
Serial ATA Power Cable
5. Connect the Serial ATA and power cables to the optical drive.
Serial ATA Power Cable
Serial ATA Cable
E. Accessories Installation
1. Unfasten expansion slot bracket screws.
Remove the back panel bracket and put the bracket aside.
The maximum size acceptable for display cards is
267mm x 98mm x 34.6mm.
PCI-e slot
PCI Express x16 slot
2. Install the PCI/PCI Express x16 card into the PCI/PCI Express x16 slots.
3. Secure the bracket.
VGA Card PCB
5mm
34.6mm
PCI Express x16 slots / PCI
Chassis
Cover
One PCI Express x16
RS232 Header-
J8
SATA 6.0Gbs-SATA 1,2
CIR Connector-JP6
J4
Serial ATA-SATA 3,4
USB3.0 Connector CN5
J7
J6
Front Connector-JP3
Slot
COM1
Socket 1155
ATX Power
Connector-ATX2
4x 240 pins DDR3
DIMM Slots
ATX Power
Connector-PWR1
Fornt panel
connector -JP7
Safety Information
Read the following precautions before setting up a Shuttle XPC.
CAUTION
Incorrectly replacing the battery may damage this computer.
Replace only with the same or equivalent as recommended by Shuttle.
Disposal of used batteries according to the manufacturer's instructions.
Laser compliance statement
The optical disc drive in this PC is a laser product.
The drive's classication label is located on the drive.
CLASS 1 LASER PRODUCT
CAUTION：INVISIBLE LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM.
Notch on the CPU/ Alignment Key of the CPU Socket
Triangle Pin1
Marking
on the CPU
Please be aware of the CPU orientation, DO NOT force the CPU into the
socket to avoid bending of pins on the socket and damage of CPU!
7. Close the metal load plate, lower the CPU socket lever and lock in place.
8. Spread thermal paste evenly on the CPU surface.
The product’s colour and specification will depend on the actual shipping product.
L
Socket 1155
CPU
Notch on the CPU/ Alignment Key of the CPU Socket
48*2=96 pin
2
3. Check that the latches are closed, and the memory module is firmly installed.
Repeat the above steps to install additional memory modules,
if required.
72*2=144 pin
3
F. Complete
1. Replace the cover and refasten the thumbscrews.
2. Complete.
Please press "Del" key while booting to enter BIOS and load the
optimised BIOS settings.
53R-SH67H3-2001
Loading...