Shuttle SH61R4 Quick Start Manual
SH61R4 Quick Guide
62R-SH61R0-0601
English.Spanish.Korean.
Traditional Chinese.Japanese.
French. German Quick Guide
Front Panel
F3
F4
F6
F4F5
Back Panel
B1
B2
B3
B4
B5
B6
B14
B13
B7
B12
B14
B11
B10
B8
DVI-I & DVI-D Ports cannot be used, if the
PCI Express graphics card is installed.
Motherboard Illustration
Clear CMOS Button
2x USB 2.0 Ports & 1x LAN
Line-Out/Line-In Ports/
J6
FRONT audio Header
AUX IN Connector-
J2
USB Header-USB2
J1
One PCI Express x1 Slot
CPU_FAN Connector-
J4
MIC Port
-JP5
AUX_IN1
FAN2
B9
F1
【
F2
English
F1. HDD LED
F2. Power Button / Power LED
F3. 5.25” Bay
F4. USB2.0 Ports
F5. Microphone
F6. Headphone
B14
B1. AC Power Socket
B2. Kensington Lock
B3.
Serial Port
(Optional)
Perforation
B4. SPDIF Out Port
(Optional)
B5. DVI-I Port
B6. DVI-D Port
B7. USB3.0 Ports
B8. Microphone Jack
B9. Line-Out Jack
B10. Line-In Jack
B11. LAN & USB2.0 Ports
B12. Clear CMOS
B13. USB2.0 Ports
Wireless LAN
B14.
Perforation
2x USB 2.0 Ports
2x USB 3.0 Ports
2x USB 2.0 Ports
DVI-D Port & DVI-I Port
S/PDIF output Connector
-SPDIF1
Intel H61 Chipset
】
Button
J3
Pin Assignments
J1
USB
Header - (USB2)
1=5V_USB 2=5V_USB
3=USB A- 4=USB B5=USB A+ 6=USB B+
7=GND 8=GND
9=NULL 10=NA
J2
AUX IN Connector - (AUX_IN1)
1=AUX_IN_L
2=Ground
3=Ground
4=AUX_IN_R
4 3 2 1
J4
Fan Connectors
SPEED_SENSE
PWM_CTRL
J5
Power Header - (JP3)
1=+HD_LED 2=PWR_LED
3=-HD_LED 4=GND
5=RST_SW 6=PWR_SW
7=GND 8=GND
9=NA 10=NULL
J6
Front audio Header - (JP5)
1=Front MIC_L 2=AGND
3=Front MIC_R 4=Front Audio detect
5=Head phone_R 6=
7=Front SENSE 8=NULL
9=Head phone_L 10=
J7
CIR connector - (JP6)
1=Ground
2=5V_DUAL
3=CIR-RX
J8
COM Header - (COM1)
1=DCD1 2=RX1
3=TXD1 4=DTR1
5=Ground 6=DSR1
7=RTS1 8=CTS1
9=-XRI 10=NULL
J9
LPC Header - (JP1)
1=+12V 11=-12V
2=5V 12=3VSB
3=5VSB 13=RI
4=SERIRQ 14=LDRQ
5=CLK-48M 15=PME
6=CLK-33M 16=LAD1
7=SIORST# 17=LAD0
8=LFRAME 18=+3.3V
9=LAD3 19=GND
10=LAD2
+12V
Ground
FAN1
Front MIC SENSE_Return
Head phone SENSE_Return
1 2 3
2 4 6 8 10
1 3 5 7 9
J3
S/PDIF Out connector - (SPDIF1)
1=Ground
2=VCC
3=SPDIF_O
1 2 3
SPEED_SENSE
PWM_CTRL
9 7 5 3 1
10 8 6 4 2
1
3
5
7
9
9 7 5 3 1
10 8 6 4 2
11 12 13 14 15 16 17 18 19
1 2 3 4 5 6 7 8 9 10
+12V
Ground
CPU_FAN2
2
4
6
8
10
A. Begin Installation
For safety reasons, please ensure that the power cord is
disconnected before opening the case.
1. Unscrew 3 thumbscrews of the chassis cover.
2. Slide the cover backwards and upwards.
2
1
3. Unfasten the rack mount screws and remove the rack.
B. CPU and ICE Installation
1. Unfasten the ICE fan thumbscrews on the back of the chassis.
2. Unfasten the four ICE module attachment screws and unplug the fan
connector.
Fan Connector
3. Remove the ICE module from the chassis and put it aside.
This 1155 pin socket is fragile and easily damaged. Always use
extreme care when installing a CPU and limit the number of times
that you remove or change the CPU. Before installing the CPU,
make sure to turn off the computer and unplug the power cord
from the power outlet to prevent damage to the CPU.
Follow the steps below to correctly install the CPU into the
motherboard CPU socket.
A
4. First unlock. Press
released from the retention tab and raise the socket lever.
A
5. Lift the metal load plate on the CPU socket.
Remove the
protective
membrane
DO NOT touch socket contacts. To protect the CPU socket, always
replace the protective socket cover when the CPU is not installed.
6. Orientate the CPU and socket, you may align the CPU notches with the
socket alignment keys. Make sure the CPU is perfectly horizontal, insert
the CPU into the socket.
with your thumb, then move it to B until it is
B
Metal load plate
Notch on the CPU/ Alignment Key of the CPU Socket
Metal load plate
Thermal Paste
Retention tab
Please do not apply excess amount of thermal paste.
9. Tear off the protective membrane from the bottom of ICE module.
Remove the protective socket mylar from the CPU socket.
10. Screw the ICE module to the mainboard. Note to press down on the
opposite diagonal corner while tightening each screw.
11. Connect the fan connector.
1
Fan Connector
12. Fasten the Smart Fan
to the chassis with the
4 thumbscrews.
4
application area
Load lever
3
2
C. Memory module Installation
Installing a memory module
DDR3 DIMMs are not compatible with DDR/DD2 or DDR DIMMs.
Be sure to install DDR3 DIMMs on this motherboard. Follow the steps below
to correctly install your memory modules in the memory sockets.
1. Unlock the DIMM latch.
2. Align the memory module's cutout with the DIMM slot notch.
Slide the memory module into the DIMM slot.
A DDR3 memory module has a cutout, so it can only fit in one direction.
1
Cutout
Latch
48*2=96 pin
2
3. Check that the latches are closed, and the memory module is firmly installed.
Repeat the above steps to install additional memory modules,
if required.
Notch
DDR3 240-pin 1.5V
72*2=144 pin
Latch
3
D. Peripheral Installation
3. Place the rack in the chassis and refasten the rack.
4. Connect the Serial ATA and power cables to the HDD.
Serial ATA Cable
Serial ATA Power Cable
5. Connect the Serial ATA and power cables to the optical drive.
Serial ATA Cable
Serial ATA Power Cable
E. Accessories Installation
1. Unfasten expansion slot bracket screws.
Remove the back panel bracket and put the bracket aside.
The maximum size acceptable for display cards is
267mm x 98mm x 34.6mm.
PCI Express
PCI Express x16 slot
2. Install the PCI Express x16 card into the PCI Express x16 slots.
3. Secure the bracket.
VGA Card PCB
5mm
34.6mm
PCI Express x16 slots / PCI
F. Complete
1. Replace the cover and refasten the thumbscrews.
Chassis
Cover
One PCI Express x16 Slot
COM Header-COM1
J8
LPC Header-JP1
J9
J4
FAN Connector-FAN1
2x 240 pins DDR3 DIMM Slots
Serial ATA-SATA 1,2,3,4
Power Header-JP3
J5
Socket 1155
ATX Power
Connector-ATX1
ATX Power
Connector-PWR1
CIR connector -JP6
J7
Safety Information
Read the following precautions before setting up a Shuttle XPC.
CAUTION
Incorrectly replacing the battery may damage this computer.
Replace only with the same or equivalent as recommended by Shuttle.
Disposal of used batteries according to the manufacturer's instructions.
Laser compliance statement
The optical disc drive in this PC is a laser product.
The drive's classication label is located on the drive.
CLASS 1 LASER PRODUCT
CAUTION：INVISIBLE LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM.
Triangle Pin1
Marking
on the CPU
Please be aware of the CPU orientation, DO NOT force the CPU into the
socket to avoid bending of pins on the socket and damage of CPU!
7. Close the metal load plate, lower the CPU socket lever and lock in place.
8. Spread thermal paste evenly on the CPU surface.
The product’s colour and specification will depend on the actual shipping product.
L
Socket 1155
CPU
Notch on the CPU/ Alignment Key of the CPU Socket
1. Loosen the purse lock and separate the Serial ATA and power cables.
2. Place the HDD and optical drive in the rack and secure with screws
from the side.
Serial ATA Optical Drive
Serial ATA HDD
2. Complete.
Please press "Del" key while booting to enter BIOS and load the
optimised BIOS settings.
53R-SH61R3-2001
Loading...