Shurflo 358-100-00 Installation Manual

358™SHURflo BILGE PUMP

Installation and Operation Instructions

MOUNTING

• Locate the pump in the deepest position in the
bilge. Keep away from high heat source.

• Mount quick disconnect bracket to bulkhead or
stringer with #10 S.S. screws. Do not drive

screws through hull.

• Route smooth I.D. discharge tubing to a thru-hull
fitting well above the water line . Avoid any
sagging or loops in the tubing. Tubing must go
up from the pump to the thru-hull fitting.

Position the discharge

Avoid

potencial

air lock

Water

Level

Incorrect position for discharge port.

Avoid sags, sharp bends, etc.

port "Up" so not
to trap air!

All connections should have double
clamps for added security.

ADVANCED BILGE PUMP FEATURES

• Anti-Airlock

• Tough Nylon Housing

• Tinned 6’ Wire Assembly

• Water Cooled Motor

• Submersible

• Ignition Protected

• ISO 8846, ABYC, NMMA Type Accepted, CE

EXPLODED VIEW

Remove all 7 screws for
cleaning if necessary.

Baseplate tabs press
in for easy removal.

ELECTRICAL

NOTE: Typical circuit only, consult boat wiring diagram.

black

12 VDC bat.

Ref. specs.

*

for fuse size

*UL approved marine duty, ignition protected, single pole
double throw switch with center off. Rated at or above 15 amps.

red

brown (+)

Automatic-on

*

Optional

Float Switch

* not supplied

ELECTRICAL WIRE:

Use 16GA wire for all circuits. If installation is over 20 feet, use 14GA wire. Brown pump wire must be
hooked to positive power for maximum flow. Wire is tinned to prevent corrosion. PANEL SWITCH:
Attach all wires to UL Marine approved duty switch with auto-off-manual, rated at or above 15 amps.
FUSE: Install a fuse per pump label specifications . CONNECTIONS: Wire connections should be made
above the highest possible water level. Seal wire connections to prevent corrosion and electrolysis.

OPERATION
DO NOT RUN PUMP DRY. ALWAYS TEST PUMP AND SWITCH BEFORE LEAVING DOCK.

Manual-on

brown (+)

black

911-742 Rev F 12/08 ECO #: 16135 Page 1 of 2

OPERATION
MANUAL MODE: To turn pump on, turn manual power switch on. If pump does not turn on, turn switch off, check power,

fuses, connections, wires. Retry. If pump does not turn on, check pump motor.

FLOW GPM [LPM] TECHNICAL DATA

Name Voltage Model #: 0 Ft [0 M] 3 Ft [1 M]

1500 *12 V 358-000-00 1800 [6813] 1700 [6434]

2000 *12 V 358-010-00 2200 [8327] 2000 [7570]

1500 24 V 358-100-00 1800 [6813] 1700 [6434]

2000 24 V 358-110-00 2200 [8327] 2000 [7570]

* Specifications given at design voltage 13.6 VDC per ABYC recommendations.

Pump Power leads: 6 ft. [1.8 M] #16 tinned stranded copper wire to minimize corrosion. Positive (+) brown; Ground (–) black.
Temperature limits: 33ºF—140ºF [0ºC—60ºC]. All models rated for continuous duty.
Approvals: Ignition Protected, ISO 8846, ABYC, NMMA Type Accepted, CE.

WARNING

Do not pump oil, diesel fuel, gasoline or other flammable liquids with this pump. This pump does not prevent the discharge of oil
or other chemicals into the water. Please take appropriate measures to prevent discharging oil or other chemicals and safeguard
the environment. Always disconnect power before servicing pump. Always use fuse size specified in specifications. These bilge
pumps are designed to evacuate standing bilge water only. These pumps may not prevent boat sinkage due to storms, rough
weather, unsafe boating, improper installation procedures or hull damage.

6 Ft [2

[6056] 14 [4.27] 8 10 1-1/8" 7 1/4" X 6"

[7191] 18 [5.5] 10 15 1-1/8" 7 1/4" X 6"

[6056] 14 [4.27] 4 6 1-1/8" 7 1/4" X 6"

[7191] 18 [5.5] 5 8 1-1/8" 7 1/4" X 6"

M]

1600

1900

1600

1900

Max Head

Ft [M] Max Amps Fuse Outlet Port Dimensions

SYMPTOM CHECK FOR

No water pumped/

Pump not running

Reduction in water

flow

Low Flow

Blown fuse. Wire connections. Impeller or float switch plugged with debris.
Impeller/screen plugged with debris. Pinch/clogged discharge tubing. Discharge tubing sagging

below pump causing air lock. Tubing must go up from pump to thru-hull fitting. Low voltage to pump;
check battery/wire connections.
Polarity reversed; check wiring. Use only smooth bore (I.D.) discharge tubing. Is thru-hull fitting I.D.
smaller than pump discharge port?

LIMITED WARRANTY

SHURflo warrants its 358 SHURflo bilge pumps to be free of defects in material and workmanship under normal use for a
period of three (3) years from date of purchase. In absence of proof of purchase, the warranty is three (3) years from the
date of manufacture indicated on the pump housing. Returns are to be shipped prepaid to SHURflo. This warranty is only
a representation of the complete Marine Products Limited Warranty outlined by Service Bulletin #1050. Please contact
SHURflo for complete warranty information.

Favor de referirse a www.shurflo.com para instrucciones de la instalación del producto y su operación, disponible en varios idiomas.

Mehrsprachige Hinweise zu Installation und Betrieb des Produktes finden Sie unter www.shurflo.com

Fare riferimento al sito www.shurflo.com per manuali multilingue di installazione ed utilizzo prodotti.

Veuillez vous réferer au site www.shurflo.com pour l'installation produit multilingue ainsi que pour le mode d'emploi.

Please refer to www.shurflo.com for multi-lingual product installation and operating instructions'

SHURflo reserves the right to update specifications, prices, or make substitutions.

SHURflo, LLC Headquarters

5900 Katella Avenue
Cypress, California 90630
Phone [phone] Ÿ Toll Free [phone]
Fax [phone]

SHURflo, LLC East

52748 Park Six Court
Elkhart, Indiana 46514-5427
Phone [phone] Ÿ Toll Free [phone]
Fax [phone]

SHURflo Europe, Middle East, Africa

Pentair Water Belgium bvba,

Industriepark Wolfstee, Toekomstlaan 30
B-2200 Herentals, Belgium
Phone [phone]Ÿ Fax [phone]

911-742 Rev F
© 2008 SHURflo, LLC All Rights Reserved

Patent #: 7371045 Page 2 of 2