Shure orporated UR1MD User Manual

UR1M Micro Bodypack Transmitter

Addendum

Specications:

The following specications apply to
the UR1M micro bodypack only.

UR1M

Frequency Range

Band Range

G1 470-530 MHz

H4, H4E 518-578 MHz

J5 578-608, 614-638 MHz

J5E 578-638 MHz

L3, L3E 638-698 MHz

Q5 740-814 MHz

Q6 740-752 MHz

Q9 740-806 MHz

Q10A 740-787 MHz

R9 790-865 MHz

R16, R18 794-806 MHz

A24 779-788, 797-806 MHz

JBX 806-810 MHz

X1 944-952 MHz

Features:

Same audio performance as UR1•

Rapid two-way infrared (IR) data transmission•

User-adjustable RF output level (10 mW or 50 mW)•

Operates with three types of primary batteries: alkaline, lithium or •
NiMH

Audio signal is input through a TA4F connector (UR1M) or a LEMO •
connector (UR1MLEMO3)

Selectable battery metering by battery type•

Audio metering on UR1M transmitter•

Battery Life (Typical):

Alkaline: 6 hours (normal RF power)

Lithium primary: 9 hours (normal RF power)

NiMH 1000 mAH: 6 hours (normal RF power)

Select Battery Type:

Set the micro bodypack transmitter switch to on
Press enterkey, then scroll using

enterkey to conrm.

Note: For the most accurate battery metering and performance, make
sure to select the correct battery type.

To open the micro bodypack transmitter, see illustrations below:

4 hours (high RF power)

7 hours (high RF power)

4 hours (high RF power)

button to select battery type. Press

Slide arrow down

RF Carrier Frequency Range

470-865, 944-952 MHz depending on region

Working Range

150 m (500 ft.), under typical conditions 500 m
(1600 ft.) line-of-sight, outdoors for a single

system

NOTE: Actual working range depends on RF signal absorption, reec­tion and interference

RF Power Output

Selectable 10 mW or 50 mW depending on region

Power Requirements:

Two 1.5V AAA alkaline, lithium primary, and NiMH batteries

Current Drain:

130 mA max. at 3V (normal RF power setting)

200 mA max. at 3V (high RF power setting)

Gain Adjustment Range

–20 to +35 dB

Transmitter LCD Interface and Controls:

For additional information on the LCD Interface and controls, see UHF-R
User Guide.

27A12268 (Rev. 1) Printed in U.S.A.
©2008 Shure Incorporated

Overall Dimensions

SHURE Incorporated http://www.shure.com
United States, Canada, Latin America, Caribbean:
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
Phone: [phone] U.S. Fax: [phone] Int’l Fax: [phone]
Europe, Middle East, Africa:
Shure Europe GmbH, Phone: [phone] Fax: [phone]
Asia, Pacific:
Shure Asia Limited, Phone: [phone] Fax: [phone]

49 mm L x 60 mm W x 17 mm D (1.9 x 2.38 x 0.66 in.)

Net Weight

62 g (2.2 oz.) without batteries

Wiring

TA4F Connector

TA4F

Microphone Element

NOTE: LAVALIER MIC TIES PINS 3 AND 4 TOGETHER—GUITAR CABLE DOES NOT.

Connector

TA4M
Connector

UR1M MIC JACK BOARD

Active Load

Audio

Ground

LEMO Connector

Microphone Element

UR1M LEMO BOARD

UR1M Transmitter Audio Input:

Connector: 4-Pin male mini connector (TA4M)

3-Pin female mini connector (LEMO
XRB.00.303)

Input Conguration: Unbalanced, active

Maximum Input Level:

(1 kHz, 1% THD)

TA4M Connector Pin

Assignments:

+5 dBu (sensitivity 0 dB)

+15 dBu (sensitivity –10 dB)

Pin 1: Ground
Pin 2: +5 VDC bias
Pin 3: Audio, 200 kΩ
Pin 4: Tied through active load (on
main board) to ground.
(On instrument adapter cable, Pin
4 oats)

LEMO Connector Pin

Assignments:

Pin 1: Ground

Pin 2: +5 VDC bias

Pin 3: Audio

(8.2 kΩ between pin 2 and 3, internal
to UR1M)

Connector

Connector

UR1M Transmitter RF Output:

Connector: SMA

Actual Impedance: 50 Ω

Pin Assignments: Shell = Ground

Center = Signal

To fully interact with the Receiver, it is recommended to upgrade the UR4 rmware to 1.50 or higher and Shure Wireless Workbench to 5.0

Certication:

UR1M: Type Accepted under FCC Parts 74 (FCC ID: DD4UR1MA, DD4UR1MB, DD4UR1MC, DD4UR1MD, DD4UR1MF, DD4UR1MG). Certied by IC in Canada
under RSS-123 and RSS-102 (IC: 616A-UR1MA, 616A-UR1MB, 616A-UR1MC-616A, 616A-UR1MD). Meets the essential requirements of the European R&TTE
Directive 99/5/EC (ETSI EN 300-422 Parts 1 & 2, EN 301 489 Parts 1 & 9) and is eligible to carry the CE marking.

The “EU Declaration of Conformity” can be obtained from Shure Inc. or any of its European representatives. For contact information please visit www.shure.com

LICENSING INFORMATION:

Licensing: A ministerial license to operate this equipment may be required in certain areas. Consult your national authority for possible requirements.
Changes or modications not expressly approved by Shure Incorporated could void your authority to operate the equipment. Licensing of Shure wireless micro­phone equipment is the user’s responsibility, and licensability depends on the user’s classication and application, and on the selected frequency. Shure strongly
urges the user to contact the appropriate telecommunications authority concerning proper licensing, and before choosing and ordering frequencies.

Information to User:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Operation of this device is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired
operation of the device.

Note: EMC conformance testing is based on the use of supplied and recommended cable types.
The use of other cable types may degrade EMC performance.

Audio

Ground

REPLACEMENT PARTS AND ACCESSORIES

Furnished Accessories

Antenna, 470-530 MHz.....................................................................UA700

Antenna, 518-578 MHz.....................................................................UA710

Antenna, 578-698 MHz ....................................................................UA720

Antenna, 740-865 MHz ....................................................................UA730

Antenna, 944-952 MHz ....................................................................UA740

Optional Accessories

Bodypack Pouch (Black) ............................................................. WA581B

Bodypack Pouch (White) ............................................................. WA581W

3-Pin mini Lemo conversion kit........................................................WA335

3-Pin mini Lemo plug for Lavalier ....................................................WA336

Assembly Tool for WA336................................................................WA337

Note

2