How it Works
Shure
Loading...
P3R PSM300 Wireless In-Ear Monitor Bodypack Receiver
Shure PSM300 Stereo Personal Monitor System User Guide
36 pgs1.51 Mb0
Table of contents
Loading...

Shure P3R PSM300 Wireless In-Ear Monitor Bodypack Receiver Shure PSM300 Stereo Personal Monitor System User Guide

Download
PSM300
Stereo Personal Monitor System
Online user guide for PSM300 stereo personal monitor system.
Version: 2.4 (2022-G)

Table of Contents

Shure Incorporated
Signal Routing to External Devices (Combination Sys
tems) 13
System Setup and Configuration 14
Rack Mounting 14
Power, Audio, and RF Connections 15
Scanning for the Best Open Channel 16
Creating a Wireless Connection Between Receivers and
Transmitters (Sync) 16
Adjusting Gain and Listening Volume 18
Operation 20
Creating Monitor Mixes 20
MixMode and Stereo Monitoring 21
Troubleshooting 23
Specifications 23
Frequency Range and Transmitter Output Power 27
Frequency Range and Transmitter Output Level 27
Optional Accessories and Replacement Parts 28
Frequencies for European Countries 28
Certifications 33
Important Product Information 33
2/36

PSM300 Stereo Personal Monitor System

IMPORTANT SAFETY INSTRUCTIONS

1.
READ these instructions.
2.
KEEP these instructions.
3.
HEED all warnings.
4.
FOLLOW all instructions.
5.
DO NOT use this apparatus near water.
6.
CLEAN ONLY with dry cloth.
7.
DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accordance
with the manufacturer’s instructions.
8.
DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other apparatus (in
cluding amplifiers) that produce heat. Do not place any open flame sources on the product.
9.
DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third
prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replace
ment of the obsolete outlet.
10.
PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11.
ONLY USE attachments/accessories specified by the manufacturer.
12.
USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Shure Incorporated
13.
UNPLUG this apparatus during lightning storms or when unused for long periods of time.
14.
REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15.
DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the
apparatus.
16.
The MAINS plug or an appliance coupler shall remain readily operable.
17.
The airborne noise of the Apparatus does not exceed 70dB (A).
18.
Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connec
tion.
19.
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
20.
Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.
21.
Operate this product within its specified operating temperature range.
3/36
Shure Incorporated

SAFETY PRECAUTIONS

The possible results of incorrect use are marked by one of the two symbols—"WARNING" and "CAUTION"—depending on the
imminence of the danger and the severity of the damage.
WARNING: Ignoring these warnings may cause severe injury or death as a result of incorrect operation.
CAUTION: Ignoring these cautions may cause moderate injury or property damage as a result of incor
rect operation.

CAUTION

•
Never disassemble or modify the device, as failures may result.
•
Do not subject to extreme force and do not pull on the cable or failures may result.
•
Keep the product dry and avoid exposure to extreme temperatures and humidity.

WARNING

•
If water or other foreign objects enter the inside of the device, fire or electric shock may result.
•
Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.
This device is able to produce sound volume higher than 85 dB SPL. Please check your maximum allowed continuous noise exposure level based on your na
tional employment protection requirements.
This product is intended for professional use only. This product should only be sold through professional sales channels.

WARNING

LISTENING TO AUDIO AT EXCESSIVE VOLUMES CAN CAUSE PERMANENT HEARING DAMAGE. USE AS LOW A VOL
UME AS POSSIBLE. Over exposure to excessive sound levels can damage your ears resulting in permanent noise-induced
hearing loss (NIHL). Please use the following guidelines established by the Occupational Safety Health Administration (OSHA)
on maximum time exposure to sound pressure levels before hearing damage occurs.
90 dB SPL
at 8 hours
110 dB SPL
at ½ hour
95 dB SPL
at 4 hours
115 dB SPL
at 15 minutes
100 dB SPL
at 2 hours
120 dB SPL
Avoid or damage may occur
105 dB SPL
at 1 hour
®
PSM 300
The PSM300 Personal Monitor System delivers wireless stereo monitoring for improved clarity and reduced feedback over tra
ditional stage wedges. Performers can create their own custom mixes by adjusting the stereo blend and overall volume level at
the bodypack, resulting in lower volume on stage and enhanced audio detail. Easy to set up and operate, PSM300 features
one-touch frequency syncing and solid wireless RF stability between transmitters and receivers. With rugged, dependable
hardware and hardworking technology, Shure PSM300 Personal Monitor Systems deliver a greatly improved monitoring expe
rience on stage.
4/36

Features

•
Send two channels of audio wirelessly to performers onstage
•
Solid RF connection over a 300 foot (90 meter) range
•
Create a personal mix on each bodypack with adjustable stereo balance or MixMode two-channel mono blend.
•
Up to 90 dB signal-to-noise ratio provides clear, detailed audio at any volume
•
Systems available with Shure Sound Isolating earphones
•
One-touch scan and IR sync quickly and easily assigns a clean wireless channel
•
No complicated menus, just simple volume and mix controls that focus on the performance
•
All-metal half-rack transmitter
•
Slim, lightweight bodypack attaches easily to a belt or guitar strap
™
®

Included Components

Shure Incorporated
*Not included in Argentina
**Not included in JB Band model
5/36

System Overview

Shure Incorporated
This example shows a typical setup for musical performance. See the System Applications section for additional examples.
① Route audio signals
Send Instrument and microphone signals from the stage to a mixer or PA system.
② Create monitor mixes
From the mixer, create two mixes: one of just the instruments, and a second with just the vocals. Route each of these to
separate mixer outputs and connect them to the P3T inputs.
③ Send wireless audio to the performers
Sync the bodypacks to the P3T transmitter to send the mixes to the performers for in-ear monitoring.
④ Adjust personal mixes
6/36
Each performer uses the MixMode knob on the bodypack to control their own mix between the instruments and vocals .

Hardware

P3T Transmitter Front and Rear Panels

① Input Level Control
Adjusts the level of the incoming audio signal
② IR Sync Window
Sends and receives group/channel data to sync receivers with the transmitter
③ Sync Button
Press to synchronize the transmitter and receiver to the same group and channel
Shure Incorporated
Note: Sync data is sent through the IR sync window
④ LCD Display
Displays audio, RF, and system information
⑤ Group Button
Press to scroll through group settings
⑥ Channel Button
Press to scroll through channel settings
⑦ Power
Turns power on or off
⑧ Power Input
Connect the supplied Shure PS24 external power supply
⑨ Mono/Stereo-MX Switch
StereoMX Sends a two-channel stereo mix to the receiver
Mono Sends a summed audio mix to both receiver channels
⑩ Line/Aux Switch
Adjust the input sensitivity using the following as a connection reference:
Aux (-10 dBV): Consumer audio devices, such as computers or portable media players
Line (+4 dBu): Mixers or other professional audio devices
7/36
⑪ Loop Outputs (¼ Inch TRS, Balanced)
Connect outputs to additional PSM systems or other audio devices
⑫ Audio Inputs (¼ Inch TRS, Balanced)
Connect to mixer outputs or other audio sources for monitoring by the performers
⑬ BNC Antenna Connector
Connect the supplied ¼ wave antenna, directional antenna, or a Shure PA411 antenna combiner
P3T Front Panel
Shure Incorporated
P3T Rear Panel
Note: For JB band models, the antenna is permanently fixed to the transmitter. Removing the antenna on JB band models is prohibited by law in Japan, and
attempting to do so may cause damage to the transmitter.

P3T Transmitter Display

① Audio Input Meter
Indicates the audio signal level
② Group / Channel / TV Setting
Displays selected group and channel settings and the corresponding television channel
8/36
Shure Incorporated
Note: the TV indicator only applies to U.S.A. channels, and remains blank in other regions
③ Lock Status
To lock or unlock the controls, press and hold the group and channel buttons until the lock icon appears/disappears.
④ Sync Status
Appears after a successful sync between the transmitter and receiver. The direction of the sync is shown as Tx>Rx (trans
mitter sends frequency to receiver) or Tx (receiver sends frequency to transmitter).
⑤ Stereo-MX / Mono Mix
Indicates whether the audio sent to the receiver is a single or two-channel mix (corresponds to the Stereo-MX/Mono switch
on the rear panel).
⑥ Aux / Line Mode
Indicates the input sensitivity setting (corresponds to the Aux/Line switch on the rear panel)
⑦ 0 dB Indicator
Turns on when input signal reaches 0 dB. Refer to the section on adjusting gain and listening volume for information on
how to use this icon.
9/36

P3R Wireless Receiver

Shure Incorporated
P3R
① Display
Shows group, channel, and MixMode settings
② Group Button
◦
Press to display group
◦
Press and hold to edit the group, then press to scroll when display flashes
10/36
Shure Incorporated
③ Channel Button
◦
Press to display channel
◦
Press and hold to edit the channel, then press to scroll when display flashes
④ IR Sync Window
Sends and receives sync data between the receiver and transmitter
⑤ Scan Button
◦
Press and hold to perform a group scan
◦
Press to perform a channel scan
Note: A channel scan selects the best channel in the current group. A group scan finds the group with the most open channels and selects the first available
channel in that group.
⑥ Antenna
⑦ Power LED Indicator
Indicates when receiver is on, remaining battery life, and when power-save mode is active. See battery life table for more
information.
⑧ Power Switch / Volume Control Knob
Turns the receiver on/off and adjusts master headphone volume level
⑨ RF LED Indicator (blue)
Illuminates when tuned to an active transmitter group and channel
⑩ Headphone Output
Connects to earphones or headphones
⑪ MixMode Control Knob
◦
When operating in MixMode, this knob blends channels 1 and 2 into a single mix
◦
When operating in stereo mode, this knob adjusts the left/right balance
⑫ Battery Compartment
Holds 2 x AA batteries

P3RA Receiver

For more demanding applications, Shure offers the P3RA receiver, which features all-metal construction and advanced menu
navigation in addition to the features included on the P3R receiver. For more information, please visit www.shure.com.

Battery Life

LED Behavior Remaining Runtime (Hours)
Green 5-7
Amber 1-3
11/36
LED Behavior Remaining Runtime (Hours)
Red (solid) 0.5-1
Red (flashing) 0
Shure Incorporated
Battery life was measured using Energizer alkaline batteries, under the following conditions:
•
Transmitter sensitivity: Line (+4dBu)
•
Audio output from receiver: dB through Shure SE112 earphones
Power-save mode: When there are no earphones plugged in, the receiver enters power-save mode to preserve battery life.
The LED slowly fades on/off in this mode and continues to display the color that represents the remaining battery life.
™

System Applications

Refer to the following PSM300 system scenarios prior to installation. Understanding the configuration options before setting up
helps to identify signal routing requirements and plan for future expansion. Specific information on how to set up the PSM300
system and create mixes for monitoring can be found in the "System Setup and Configuration" and "Operation" sections of this
user guide.

Single System for an Individual Performer

This configuration provides inear monitoring in a solo performance, or in a group performance in which only one person re
quires wireless monitoring. This system can be expanded for multiple performers by using additional P3R bodypack receivers
tuned to the same transmitter.

Single Transmitter with Multiple Receivers

Multiple performers can monitor audio from the same transmitter and still adjust the signal at their bodypack to personalize the
mix. Simply tune each bodypack to the same frequency as the transmitter and use the MixMode knob to adjust the mix.

MixMode or Stereo Operation:

Each performer has the option of setting their bodypack to MixMode or Stereo when the transmitter is set to Stereo-MX. When
the bodypack is powered on, it is set to stereo by default. To operate in MixMode, hold the GROUP button when turning the
power on. For information on these modes, see "MixMode and Stereo Monitoring".
12/36
Shure Incorporated

Multiple Transmitters with Separate Mixes

When several performers in a group have different monitoring requirements, multiple PSM300 systems may be used simulta
neously to send different mixes through each transmitter. This setup requires a mixer with two monitor/auxiliary outputs for
each transmitter.
Tip: To simplify setup in applications that involve multiple transmitters, Shure offers the PA411 antenna and power distribution system, which supplies up to
four PSM transmitters with power and RF from a single source.

Signal Routing to External Devices (Combination Systems)

The LOOP outputs pass audio to an external device, such as other personal monitoring systems, recording devices, or stage
monitors. The signal at the LOOP outputs is identical to the signal coming from the mixer, and is not affected by the transmitter
volume or input sensitivity (line/aux) settings. This makes the LOOP outputs particularly useful when using a mixer that has
one or two monitor/auxiliary sends.
13/36
Shure Incorporated

Using the PSM300 simultaneously with Loudspeakers:

A combination monitoring system can be used, where some of the performers are using the PSM300 wireless system and oth
ers are listening through loudspeakers on stage.
Note: If using passive stage monitors, the P3T outputs must be connected to an amplifier. Active (amplified) speakers can be connected directly to the P3T
outputs.

Using the PSM300 Combined with Other Wireless Monitoring Systems

In a scenario where two performers have their own wireless monitoring systems (one Shure PSM300 system and one third-
party system, for example), the PSM300 can pass the signal from the mixer on to the second monitoring system.

System Setup and Configuration

Rack Mounting

The P3T Transmitter can be mounted in a standard 19inch rack. Up to two units can be mounted in a single rack space. If us
ing multiple P3T transmitters, the Shure PA411 Antenna Combiner system can be used to consolidate and distribute all RF and
power for up to four transmitters.
14/36
Shure Incorporated
Note: Always use both straddle bars when mounting two units.

Power, Audio, and RF Connections

1.
Use the power adapter to connect the P3T to an AC power source.
2.
Install 2 AA batteries in the bodypack receiver.
3.
Attach the antenna to the BNC antenna connector on the P3T rear panel.
4.
Connect the mixer or audio source to the P3T audio inputs using ¼ inch balanced cables.
Important: When connecting to only one transmitter input, use the LEFT/CH1 input. Set the transmitter to MONO to hear audio on both channels of
the receiver.
15/36

Scanning for the Best Open Channel

Follow these steps to scan the RF environment and find the best available frequency for operation:
1.
Turn on the bodypack receiver and any potential sources of interference, including wireless systems, computers, audio
equipment, cellular phones, LED panels, and other electronic devices that will be in use during a performance.
2.
Make sure the P3T transmitter is OFF.
3.
Position the receiver in the performance area and press SCAN to survey the available channels within the current
group setting.
If using several PSM300 systems or operating in a location with a high volume of wireless devices, perform a group
scan first, followed by a channel scan:
Group Scan: Press and hold the SCAN button on the receiver.
Channel Scan: Press the SCAN button on the receiver.
Shure Incorporated

Creating a Wireless Connection Between Receivers and Transmitters (Sync)

To pass audio from the transmitter to the receiver, both must be tuned to the same frequency. The easiest way to configure the
system is to use the automatic sync feature. This transfers group and channel settings with a press of a button. Based on your
system configuration, use one of the following processes to sync the components:
16/36
Align the IR windows to sync the receiver and transmitter
Shure Incorporated
Pressing the SYNC button transfers group/channel data

Single Transmitter and Receiver

The following sync procedure should be used with a setup that consists of a single transmitter and receiver, unless a group/
channel setting has been assigned prior to a performance.
Sync from receiver to transmitter:
1.
Perform a scan on the receiver (see "Scanning for the Best Open Channel" for best practices).
2.
Align the IR windows on the receiver and transmitter. The windows should be 6-11 cm apart.
3.
Press the SYNC button on the transmitter while the blue RF LED on the receiver is flashing.
4.
The Transmitter displays SYNC when the sync is successful. The arrow between Rx (receiver) and Tx (transmitter)
shows the direction of the sync.
17/36
Shure Incorporated
Note: When the RF LED on the receiver is flashing after performing a scan, the receiver sends its frequency setting to the transmitter. After it stops
flashing, pressing SYNC sends the frequency setting from the transmitter to the receiver.

Single Transmitter and Multiple Receivers

The following sync procedure should be used with a setup that consists of a single transmitter with multiple receivers, or if a
specific group/channel setting has been assigned to the transmitter prior to a performance.
Sync from transmitter to receivers:
1.
Sync the first receiver to the transmitter using the sync procedure for a single receiver. Performing a scan and using the
resulting group and channel from the receiver is recommended.
2.
Set additional receivers to the transmitter frequency (one at a time) using IR sync:
◦
Align the IR windows on the receiver and transmitter and press SYNC.
◦
The receiver LED should not be flashing when pressing SYNC.
Note: Receivers can also be manually tuned to the transmitter if an IR sync is not practical.

Multiple Transmitters and Multiple Receivers

1.
Set up the first transmitter and all associated receivers according to the appropriate sync procedure. Keep the transmit
ter and all receivers from this first system powered on when setting up additional systems.
2.
Set up each additional system using the appropriate sync process. Always leave each new system on before setting up
an additional one.

Manual Selection

If frequencies have been planned ahead of time, the group and channel can be set manually without performing a scan. Refer
to the frequency table at the end of this user guide to identify frequencies for each group/channel setting.
To select group/channel settings on the receiver and transmitter:
1.
Press GROUP to scroll through group settings.
2.
Press CHANNEL to scroll through channel settings within the selected group.

Adjusting Gain and Listening Volume

For the best audio quality, start by adjusting the levels from the mixer or audio source, and then adjust levels through the
PSM300 system. This approach corresponds to the way that the audio signal flows through the system, and maximizes the sig
nal-to-noise ratio.
Before you begin: verify all signal routing and gain settings at the mixer or source prior to adjusting any levels from the
PSM300 system. If the sound is distorted or faint when it enters the P3T transmitter, there is likely an issue elsewhere in the
signal chain that needs to be resolved.
18/36
Shure Incorporated

① Adjust Transmitter Levels:

Input Sensitivity
Select the setting that matches the input source:
Line (+4 dBu) Use with mixers or other professional audio devices that send line-level signals.
Aux (-10 dBV) Use when connecting consumer audio devices such as portable audio players or computers.
Note: When using consumer audio devices, the output volume of the device should typically be adjusted as close to the maximum setting as possible without
distorting or clipping at the output of the device. This maximizes the signal-to-noise ratio.
Input Level
Adjust the level so that average levels on the audio meter reach approximately 75% of the full range. The highest levels
should occasionally hit the 0dB indicator on the audio input meter, without reaching the OL (overload) indicator.
Tip: If a sound check before the performance is possible, everyone should play at the loudest anticipated volume so that attenuation is not required during the
performance.

② Adjust Receiver Volume:

After levels are established at the mixer and transmitter, use the headphone volume control on the bodypack receiver to adjust
overall listening volume. For information on adjusting the left/right balance or customizing the mix blend, see "MixMode and
Stereo Monitoring".
19/36
Shure Incorporated

Operation

Creating Monitor Mixes

The mix that performers hear on stage is usually different than the mix heard by the audience. In live sound applications, the
engineer creates a separate mix to send to the performer by routing the input signals to specified mixer outputs, usually called
Monitor or Auxiliary outputs.
The following scenario demonstrates a generic signal path for monitoring mixes, and may not reflect the routing for all mixer
types. Consult the user guide for your mixer for detailed signal routing options.
① Mixer Channel
② Monitor/Auxiliary Sends
③ Wireless Transmission
Each mixer channel controls audio processing and routing for a single audio source. In this
example, a vocal microphone is plugged into the mixer channel.
Adjust the signal levels to send to the monitor/auxiliary outputs, each of which corresponds
to a separate monitoring mix. Each of these mixes are sent to separate channels on the P3T
transmitter.
Note: The channel faders on most mixers do not affect the volume of the monitor/auxiliary sends.
Each monitoring mix is transmitted on a separate channel to the P3R receiver. The MixMode
knob on the bodypack adjusts the blend between the audio from channel 1 and channel 2.
20/36
Shure Incorporated

MixMode and Stereo Monitoring

The receiver can operate in stereo or MixMode when the transmitter is set to STEREO-MX. In applications that involve multiple
bodypack receivers tuned to a single transmitter, some bodypacks can operate in stereo, while others operate in MixMode.

Selecting the Mode

Stereo: The receiver is set to stereo mode by default. To switch from MixMode to stereo, simply turn the receiver off and it will
return to stereo mode when powered back on.
MixMode: Press and hold the GROUP button on the bodypack receiver while turning the power on. The MixMode indicator
light on the receiver display turns on to confirm the setting. The receiver will return to stereo mode after it has been powered
off.
21/36
Shure Incorporated

Stereo

Audio from channel 1 is heard on the left earphone, while audio from channel 2 is heard on the right earphone. Listening in
stereo mode increases separation between the sources on each channel, which can improve clarity when many sources are
being monitored. The MixMode knob on the bodypack adjusts left/right balance when operating in stereo mode.

MixMode

MixMode allows performers to adjust the blend between two monitoring mixes (an instrumental mix and a vocal mix, for exam
ple). When using MixMode:
•
Each mix is heard through both the left and right earphones
•
The MixMode knob adjusts the volume blend between the two monitor mixes (channel 1 and channel 2)
•
Each bodypack receiver can dial in a unique blend to meet the monitoring needs of each performer
Adjusting mix levels
In this scenario, an instrumental mix is on channel 1 and a vocal mix is on channel 2:
To hear more of channel one, turn the MixMode knob to the left.
To hear more of channel two, turn the MixMode knob to the right.

When to Use the Mono Setting

In some cases, only a single input on the transmitter is used (if the mixer only features a single monitor/auxiliary output, for ex
ample). To ensure that audio is heard on both the left and right earphones:
•
Use the LEFT/CH1 input on the transmitter
•
Set the transmitter to MONO
22/36
Note: When the transmitter is set to mono operation, the MixMode knob will not affect the sound.

Troubleshooting

Problem Solution
Check the volume levels at the P3T transmitter and verify that the meter is not reaching the overload
indicator
Check levels going in and out of the mixer. If audio is distorting anywhere in the signal chain, it will be
distorted even if the PSM300 system is not overloading.
Make sure batteries in the receiver are fresh
Verify that the cables are 1/4 inch balanced. If an unbalanced instrument or speaker cable is used, it
may introduce noise.
Distorted Audio
Tip: To tell the difference, look at the connectors on the cable. The metal connector on a balanced cable has two plastic rings
that divide it into three separate sections (tip, ring, sleeve). An unbalanced cable only has a single plastic ring that divides the
metal portion into two sections (tip, sleeve).
Shure Incorporated
No sound from re
ceiver
Turning the Mix
Mode knob does
not affect the
sound
Low audio output
at the receiver
Check that all cables are plugged all the way into the mixer and the P3T inputs. Sometimes, if a ca
ble is not fully inserted, the signal will be faint and distorted.
Make sure you are using the line-level outputs from the mixer. If you have a powered mixer, do not
use the main speaker outputs, as they are amplified signals and will overload the P3T inputs.
Make sure the transmitter and receiver are linked to the same group and channel
Verify levels are registering at the transmitter and that the volume is turned up on the receiver
Check that the receiver is on and that the headphones are properly connected to the receiver
The StereoMX/Mono switch on the rear panel of the P3T may be switched to mono. For the Mix
Mode knob to work, the transmitter must be set to Stereo-MX.
Verify that the signals going from the mixer to the transmitter are not identical
Check that the bodypack is set to MixMode
Check headphone connection and volume level
If only sending a single channel into the P3T transmitter, check it the MixMode knob isn't turned to
wards a silent channel. If using one channel, set the P3T transmitter to mono mode.
Perform a scan to ensure the receiver is on a clear (available) frequency
Make sure there is a line-of-sight path between the transmitter antenna and the bodypack receivers
Audio or RF drops
out
IR sync failure Verify distance between receiver and transmitter is between 6-11 cm
Verify that other wireless devices that are being monitored, such as wireless microphones, are not
experiencing RF dropouts
If using an antenna other than the one included with the system, make sure it is designed to operate
in the correct frequency range
23/36

Specifications

RF Carrier Range

488 937.5 MHz
varies by region

Compatible Frequencies

Per band
up to 15

Tuning Bandwidth

24 MHz Maximum
Note: varies by region

Operating Range

environment dependent
90 m ( 300 ft)
Shure Incorporated

Audio Frequency Response

38 Hz–15 kHz

Signal-To-Noise Ratio

A-Weighted
90 dB (typical)

Total Harmonic Distortion

ref. ±34 kHz deviation @1 kHz
<0.5% (typical)

Companding

Patented Shure Audio Reference Companding

Spurious Rejection

ref. 12dB SINAD
>80 dB (typical)

Latency

<0.7 ms

Frequency Stability

±2.5 ppm

MPX Pilot Tone

19 kHz (±1 Hz)

Modulation

FM*, MPX Stereo
24/36
*ref. ±34 kHz deviation @1 kHz

Operating Temperature

-18°C to +63°C
P3T

RF Output Power

10, 20, 30 mW
Note: varies by region

RF Output Impedance

50 Ω (typical)

Net Weight

783 g(27.6 oz.)
Shure Incorporated

Dimensions

43 x 198 x 172 mm (1.7 x 7.8 x 6.8 in.), H x W x D

Power Requirement

1215V DC, 260 mA Maximum

Audio Input

Connector Type

6.35 mm (1/4") TRS

Polarity

Tip positive with respect to ring

Configuration

Electronically balanced

Impedance

40 kΩ (actual)

Nominal Input Level

switchable: +4 dBu, –10 dBV

Maximum Input Level

+4 dBu +22 dBu
10 dBV +12.2 dBu

Pin Assignments

Tip=hot, Ring=cold, Sleeve=ground
25/36

Phantom Power Protection

Up to 60 V DC

Audio Output

Connector Type

6.35 mm (1/4") TRS

Configuration

Electronically balanced

Impedance

Connected directly to inputs
P3R

Active RF Sensitivity

at 20 dB SINAD
2.2 µV
Shure Incorporated

Image Rejection

>90 dB

Adjacent Channel Rejection

>60 dB

Intermodulation Attenuation

>50 dB

Blocking

>60 dB

Audio Output Power

1kHz @ <1% distortion, peak power, @32Ω
40 mW + 40 mW

Minimum Load Impedance

4 Ω

Headphone Output

3.5 mm (1/8″) stereo

Output Impedance

<2.5 Ω

Net Weight

98 g(3.5 oz.) (without batteries)
26/36

Dimensions

110 x 64 x 21 mm H x W x D

Battery Life

5–7 hours (continuous use) AA batteries

Frequency Range and Transmitter Output Power

Frequency Range and Transmitter Output Level

Band Range Output Power
G20 488 to 512 MHz 30 mW
H8E 518 to 542 MHz 10 mW
H20 518 to 542 MHz 30 mW
Shure Incorporated
H62 518 to 530 MHz 10 mW
J10 584 to 608 MHz 30 mW
J13 566 to 590 MHz 30 mW
JB 806 to 810 MHz 10 mW
K3E 606 to 630 MHz 30 mW
K12 614 to 638 MHz 30 mW
L18 630 to 654 MHz 10 mW
L19 630 to 654 MHz 30 mW
M16 686 to 710 MHz 30 mW
M18 686 to 710 MHz 10 mW
Q12 748 to 758 MHz 30 mW
Q25 742 to 766 MHz 30 mW
R12 794 to 806 MHz 10 mW
S8 823 to 832 MHz 20 mW
T11 863 to 865 MHz 10 mW
X7 925 to 937.5 10 mW
Note: Frequency bands might not be available for sale or authorized for use in all countries or regions.
NOTE: This Radio equipment is intended for use in musical professional entertainment and similar applications. This Radio apparatus may be capable of oper
ating on some frequencies not authorized in your region. Please contact your national authority to obtain information on authorized frequencies and RF power
levels for wireless microphone products.
27/36

Optional Accessories and Replacement Parts

Bodypack receiver P3R
Half-rack Transmitter P3T
Universal bodypack receiver P3RA
Antenna and power distribution system PA411
Wired PSM bodypack P9HW
Dynamic MicroDriver earphones SE112
Dynamic MicroDriver earphones SE215
High-definition MicroDriver earphones with tuned bass port SE315
High-definition earphones with dual MicroDrivers SE425
Shure Incorporated
High-definition earphones with triple MicroDrivers SE535
High-definition earphones with quad MicroDrivers SE846
Carrying/Storage Bag 95A2313
1/4 Wave Antenna (748–865 MHz) for SLX Wireless System UA400
1/4 wave antenna (470-752 MHz) UA400B
Single Rack Mount Kit RPW503
Dual Rack Mount Kit RPW504

Frequencies for European Countries

H8E 518-542 MHz

Country Code
Frequency Range
Code de Pays
Codice di paese
Código de país
Länder-Kürzel
A, B, BG, CH, CY, CZ, D, EST 518 - 542 MHz*
F, GB, GR, H, I, IS, L, LT 518 - 542 MHz*
Gamme de frequences
Gamme di frequenza
Gama de frequencias
Frequenzbereich
28/36
Shure Incorporated
Country Code
Code de Pays
Codice di paese
Código de país
Länder-Kürzel
NL, P, PL, S, SK, SLO 518 - 542 MHz*
DK, FIN, M, N *
HR, E, IRL, LV, RO, TR *
* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.
Frequency Range
Gamme de frequences
Gamme di frequenza
Gama de frequencias
Frequenzbereich

H20 518-542 MHz

Country Code
Code de Pays
Frequency Range
Gamme de frequences
Codice di paese
Código de país
Länder-Kürzel
A, B, BG, CH, CY, CZ, D, DK, EST, F 518 - 542 MHz*
FIN, GB, GR, H, HR, I, IRL, IS, L, LT 518 - 542 MHz*
M, N, NL, P, PL, RO, S, SK, SLO, TR 518 - 542 MHz*
all other countries *
* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.
Gamme di frequenza
Gama de frequencias
Frequenzbereich

K3E 606-630 MHz

Country Code
Code de Pays
Codice di paese
Frequency Range
Gamme de frequences
Gamme di frequenza
Código de país
Länder-Kürzel
A, B, BG, CH, CY, CZ, D, EST 606 - 630 MHz*
Gama de frequencias
Frequenzbereich
29/36
Shure Incorporated
Country Code
Code de Pays
Codice di paese
Código de país
Länder-Kürzel
F, GB, GR, H, I, IRL, L, LT 606 - 630 MHz*
NL, P, PL, S, SK, SLO 606 - 630 MHz*
DK, FIN, M, N *
HR, E, IRL, LV, RO, TR *
* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.
Frequency Range
Gamme de frequences
Gamme di frequenza
Gama de frequencias
Frequenzbereich

K12 614-638 MHz

Country Code
Frequency Range
Code de Pays
Codice di paese
Código de país
Länder-Kürzel
A, B, BG, CH, CY, CZ, D, DK, EST, F 614 - 638 MHz*
FIN, GB, GR, H, HR, I, IRL, IS, L, LT 614 - 638 MHz*
M, N, NL, P, PL, RO, S, SK, SLO, TR 614 - 638 MHz*
all other countries *
* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.
Gamme de frequences
Gamme di frequenza
Gama de frequencias
Frequenzbereich
30/36

M16 686-710 MHz

Shure Incorporated
Country Code
Code de Pays
Codice di paese
Código de país
Länder-Kürzel
A, B, BG, CH, CY, CZ, D, DK, EST, F 686 - 710 MHz*
FIN, GB, GR, H, HR, I, IRL, IS, L, LT 686 - 710 MHz*
M, N, NL, P, PL, RO, S, SK, SLO, TR 686 - 710 MHz*
all other countries 686 - 710 MHz*
* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.
Frequency Range
Gamme de frequences
Gamme di frequenza
Gama de frequencias
Frequenzbereich

R12 796-806 MHz

Country Code
Frequency Range
Code de Pays
Codice di paese
Código de país
Länder-Kürzel
N 796 - 806 MHz*
A, B, BG, CH, CY, CZ, D, DK, E, EST *
F, FIN, GB, GR, H, HR, I, IRL, IS, L, LT *
LV, M, NL, P, PL, S, SK, SLO, TR *
* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.
Gamme de frequences
Gamme di frequenza
Gama de frequencias
Frequenzbereich
31/36

S8 823-832 MHz

Shure Incorporated
Country Code
Code de Pays
Codice di paese
Código de país
Länder-Kürzel
BG, CH, D, DK, EST, F, FIN, IS, N, NL, S license free*
A, B, CY, CZ *
E, GB, GR, H, HR *
I, IRL, LV, L, LT, M, P, PL *
SK, SLO, RO, TR *
* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.
Frequency Range
Gamme de frequences
Gamme di frequenza
Gama de frequencias
Frequenzbereich

T11 863-865 MHz

Country Code
Code de Pays
Codice di paese
Código de país
Länder-Kürzel
A, B, BG, CH, CY, CZ, D, DK, E, EST license free
F, FIN, GB, GR, H, HR, I, IRL, IS, L, LT license free
LV, M, N, NL, P, PL, S, SK, SLO license free
TR 863 - 865 MHz*
* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.
Frequency Range
Gamme de frequences
Gamme di frequenza
Gama de frequencias
Frequenzbereich
32/36

Q25 614-638 MHz

Shure Incorporated
Country Code
Code de Pays
Codice di paese
Código de país
Länder-Kürzel
A, B, BG, CH, CY, CZ, D, EST 742 - 766 MHz*
F, GB, GR, H, I, IS, L, LT 742 - 766 MHz*
NL, P, PL, S, SK, SLO 742 - 766 MHz*
RO 742 - 743; 750 - 751; 758 - 759 MHz*
HR, E, IRL, LV, TR, DK, RIN, M, N *
* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.
Frequency Range
Gamme de frequences
Gamme di frequenza
Gama de frequencias
Frequenzbereich

Certifications

Industry Canada ICES-003 Compliance Label: CAN ICES-3 (B)/NMB-3(B)
Complies with requirements set out in RSS-GEN.
Certified by ISED in Canada under RSS-123 and RSS-102.
Certified by ISED in Canada under RSS-102 and RSS-210.
IC: 616A-P3TT.
IC: 616A-P3TA, 616A-P3TB, 616A-P3TD.
FCC: DD4P3TA, DD4P3TB, DD4P3TD, DD4P3TT.
Approved under the Declaration of Conformity (DoC) provision of FCC Part 15.
Certified under FCC Part 74.

Important Product Information

CE Notice:

Hereby, Shure Incorporated declares that this product with CE Marking has been determined to be in compliance with Euro
pean Union requirements. The full text of the EU declaration of conformity is available at the following site: https://
www.shure.com/en-EU/support/declarations-of-conformity.
Authorized European Importer / Representative:
Shure Europe GmbH
Department: Global Compliance
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
33/36
Shure Incorporated
Phone: +49-7262-92 49 0
Fax: +49-7262-92 49 11 4
Email: EMEAsupport@shure.de

UKCA Notice:

Hereby, Shure Incorporated declares that this product with UKCA Marking has been determined to be in compliance with UK
CA requirements. The full text of the UK declaration of conformity is available at the following site: https://www.shure.com/en-
GB/support/declarations-of-conformity.
Authorized UK Importer / Representative:
Shure UK Limited
Unit 2, The IO Centre, Lea Road,
Waltham Abbey, Essex, EN9 1 AS, UK เครื่องโทรคมนาคมและอุปกรณ์นี้มีความสอดคล้องตามมาตรฐานหรือข้อกำหนดทางเทคนิคของ กสทช.
（一）本产品符合“微功率短距离无线电发射设备目录和技术要求”的具体条款和使用场景；
（二）不得擅自改变使用场景或使用条件、扩大发射频率范围、加大发射功率（包括额外加装射频功率放大器），不得擅自更改 发射天线；
（三）不得对其他合法的无线电台（站）产生有害干扰，也不得提出免受有害干扰保护；
（四）应当承受辐射射频能量的工业、科学及医疗（ISM）应用设备的干扰或其他合法的无线电台（站）干扰；
（五）如对其他合法的无线电台（站）产生有害干扰时，应立即停止使用，并采取措施消除干扰后方可继续使用；
（六）在航空器内和依据法律法规、国家有关规定、标准划设的射电天文台、气象雷达站、卫星地球站（含测控、测距、接收、
导航站）等军民用无线电台（站）、机场等的电磁环境保护区域内使用微功率设备，应当遵守电磁环境保护及相关行业主管部门 的规定。
低功率射頻器材技術規範
取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅
自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻器材之使用
不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並
改善至無干擾時方得繼續使用。前述合法通信，指依電信管理法規定作業之
無線電通信。低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻
射性電機設備之干擾。

Information to the user

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the manufacturer's instruction manual, may cause interference with radio and television reception.
Notice: The FCC regulations provide that changes or modifications not expressly approved by Shure Incorporated could void
your authority to operate this equipment.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip
ment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter
mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the fol
lowing measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and the receiver.
•
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
34/36
Shure Incorporated
•
Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1.
This device may not cause harmful interference.
2.
This device must accept any interference received, including interference that may cause undesired operation.
Note: EMC conformance testing is based on the use of supplied and recommended cable types. The use of other cable types may degrade EMC perfor
mance.
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the
equipment.
Please follow your regional recycling scheme for batteries, packaging, and electronic waste.
Canada Warning for Wireless
This device operates on a noprotection, nointerference basis. Should the user seek to obtain protection from other radio ser
vices operating in the same TV bands, a radio licence is required. For further details, consult Innovation, Science and Econom
ic Development Canada’s document Client Procedures Circular CPC2128, Voluntary Licensing of LicenceExempt LowPow
er Radio Apparatus in the TV Bands. Ce dispositif fonctionne selon un régime de non‑brouillage et de non‑protection. Si l’utilisateur devait chercher à obtenir une
certaine protection contre d’autres services radio fonctionnant dans les mêmes bandes de télévision, une licence radio serait
requise. Pour en savoir plus, veuillez consulter la Circulaire des procédures concernant les clients CPC‑2‑1‑28, Délivrance de
licences sur une base volontaire pour les appareils radio de faible puissance exempts de licence et exploités dans les bandes
de télévision d’Innovation, Sciences et Développement économique Canada.
This device contains licenceexempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Develop
ment Canada’s licenceexempt RSS(s). Operation is subject to the following two conditions:
1.
This device may not cause interference.
2.
This device must accept any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes :
1.
L’appareil ne doit pas produire de brouillage;
2.
L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
The antenna(s) must be installed such that a minimum separation distance of 20 cm is maintained between the radiator (anten
na) and all persons at all times.
La ou les antennes doivent être installées de telle façon qu'une distance de séparation minimum de 20 cm soit maintenue en
tre le radiateur (antenne) et toute personne à tout moment.

Australia Warning for Wireless

This device operates under an ACMA class licence and must comply with all the conditions of that licence including operating
frequencies. Before 31 December 2014, this device will comply if it is operated in the 520-820 MHz frequency band.
WARNING: After 31 December 2014, in order to comply, this device must not be operated in the 694-820 MHz band.

LICENSING INFORMATION

Licensing: A ministerial license to operate this equipment may be required in certain areas. Consult your national authority for
possible requirements. Changes or modifications not expressly approved by Shure Incorporated could void your authority to
operate the equipment. Licensing of Shure wireless microphone equipment is the user’s responsibility, and licensability de
35/36
Shure Incorporated
pends on the user’s classification and application, and on the selected frequency. Shure strongly urges the user to contact the
appropriate telecommunications authority concerning proper licensing, and before choosing and ordering frequencies.
36/36
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use