Shure M95ED User Guide
222
HARTREY AVE
AREACODE
TWX:
910-231-0048
EYlNSTDN
31118667200.
11
60104
il
LAtlLt bHJRtMICWO
TELEX:
72-4381
THE PREMIER FAMILY OF STEREO SOUND REPRODUCERS
STEREO DYNETIC@
M95ED
CARTRIDGE AND STYLI SPECIFICATIONS
N95ED
5 X l8y
(.0002
.0007 in.)
Biradial
(Elliptical)
N95-3f
63 microns
(.0025 in.)
Spherical
toptional
'Output voltages given for stereo cut record. For MONO cut record,
"Tracking forces
NET WEIGHT:
INDUCTANCE: 650 mlllihenrres
DC RESISTANCE: 1550 ohm?
OPTIMUM LOAD: 47,000 ohms resrstance in parallel wlth 400 to 500 prco-
farads total capacitance per channel. (Load resistance can be as high ar
100,000 ohms and total capacltance can be as low as 100 prcofarads wrth
only mrnor audlble change.) Total capacrtance ~ncludes the capacitances of
the tone arm
FOUR-CHANNEL: This Stereo
four-channel matrix systems.
MONOPHONIC OPERATION: Set
or
right channels
CONNECTIONS (see Figure
ground (usually green) to "KG." Left "hot" lead (usually whrte) to "L,"
left ground (usually blue) to
hum, remove the ground tab. The
from the right channel ground by the removal of the ground tab.
CAUTION: Do not make solder
connection to cartridge terminals.
STYLUS REPLACEMENT (see
ure
stylus and gently pull forward
out of cartridge.
ment stylus into socket and press
until housing mates with cartridge
case.
MOUNTING
mounting centers]:
Mounting screws are provided.
1.
2.
3. Lay cartridge in shell and align
4. Reinsert stylus (see Stylus Re-
RECOMMENDED STYLUS CLEANING:
or smaller), trimmed to approximately 6 mni (1/4 in.), dipped in alcohol or
an alcohol-distilled water solution. Commercial cleaning solutions may cause
stylus damage or corrosion. Always brush stylus from back to front; never
brush or wipe stylus from front to back or side to side.
TO PRESERVE STYLUS LIFE:
1.
2.
3. If it is necessary to manually place the tone arm in the record groove
4. Correct improper set-down adjustment or malfunction of the turntable
5.
6.
7.
8. When dusting the turntable protect the stylus with the stylus guard.
SPECIAL NOTE:
cartridge, be certain that any replacement stylus you buy bears the following certification on the package: "This Stereo
manufactured by Shure Brothers Inc." AVOID INFERIOR IMITATIONS. THEY
WILL SERIOUSLY,,DECRADE THE PERFORMANCE OF YOUR CARTRIDGE.
ALL GENUINE
BROTHERS
For more information on your Shure stylus, write for booklet:
the
FULL ONE-YEAR WARRANTY: Shure Brothers lncorporated
222 Hartrey Avenue, Evanston,
product that rt will be free, in normal use, of any defects in workmanship
and
retain
damages. It this Shure product has any defects as described above, care-
fully repack the unit and return it prepaid to:
If you are not in the United States, return the unit to your dealer
Authorized Service Center for repair. The unit will be repaired or replaced
and returned lo you promptly, and
you may elect to receive a refund.
PATENT NOTICE:
of the following U.S. patents: 3,055,988, 3,077,521, 3,077,522, and 3,463,889.
Copyright 1981, Shure Brothers Inc.
27A1247 (AH) Printed in U.S.A.
Yellow
4.7
X
Dark
Green
78
output voltage at both left channel and right channel cartridge terminals
will be 71% of figures above.
"A+B." If amplrfier is not equlpped with this swttch, connect left and
2):
Grasp molded housing of
Remove stylus guard and stylus
Stylus Replacement).
(see
Connect leads to cartridge (see
Figure
1).
mounting holes on side of cartridge with holes or threads in
shell. Follow turntable manufacturer's instructions to mount
cartridge in tone arm or plug-in
shell.
placement). FIGURE
Follow turntable or tone arm instructions when adjusting antiskating
force.
Do not handle the tone arm while it is in operation since this may
cause the arm to sweep across the record.
while turntable is rotating, release it as soon as the stylus engages the
record groove.
changrng mechanism to prevent the stylus irom strrklng the edge of the
turntable or record. Do not stack more records than turntable
turer recommends.
Take care to properly insert the stylus into the cartridge assembly and
the cartridge and shell assembly into the tone arm receptacle.
Use proper vertical tracking force setting for each cartridge.
Do not use badly warped, cracked or imperfect records.
INC. LOOK FOR THE NAME SHURE ON THE STYLUS GRIP.
Small World of a Stylus."
materrals lor a period of one year from date of purchase. You should
proof of date of purchdse. Shure
mV
20,000
5.5
mV
20,000
rpm Stylus: Set amplifier to "MONO" or "A+B."
greatel than maximum ind~cated should not be used.
6.3
grams
wrrlng, phono cables, and the ampllfler input circurt.
In parallel.
Insert replace-
112.7
mm
(112
To maintain the
DYNETIC@" STYLI ARE MANUFACTURED BY SHURE
Shure Brothers lncorporated
Attention: Service Department
1501 West Shure Drive
Arlington Heights, Illinois 60004
Cartridge
PHONOGRAPH CARTRIDGE
20 to
Hz
20
to
Hz
Dynetic@ cartridge is compatible with all
1):
Right "hot" lead (usually red) to "R," rrght
"LC." If metal head is causing ground loop
Fig-
in.)
Illinois 60204, warrants to the owner of
and stylus manufactured under one or more
25 dB
3/q
within
2 dB
1
-
-
iunct~on swltch on ampl~frer to "MONO"
metalllc cartr~dge shleld is
at
kHz
1
grams
1%
to
grams
to
3
400
1,000
10,000
at 1 gram
Hz
-
Hz - 33
Hz
-
--
disconnected
i;JT;;;;F,
S~O~~O
C""""i
(BLYL
anel
FlQURE
1
2
Use a camel's hair brush (No. 2
orig~nal performance standards of your
Dynetic8 stylus is
"A
("Shure"),
18
not liable for any consequentral
if it cannot be repaired or replaced,
Thrs warranty does not include stylus wear.
24 cm/sec
cm/sec
19 cm/sec
GREEN
manuiac-
precision
Visit to
S
RING1
srze
thrs
A
or
Loading...