Shure M80E-D User Guide
222
AREA
HARTREY
COOE
312f328.9000
AYE
EVANSTON.
*
ILL.
160204)
CABLE
U
5
A
SHUREMICRO
QDEL
M80E-D
SPECIFICATIONS
MODELS
MIBE,
___
TRACKING ANGLE:
FREQUENCY
RESPONSE:
OUTPUT VOLTAGE:
CHANNEL
SEPARATION:
CHANNEL
BALANCE:
RECOMMENDED
LOAD IMPEDANCE:
INDUCTANCE:
D.C. RESISTANCE:
STYLUS MODEL
N55E:
COMPLIANCE:
TRACKING FORCE:
REPLACEMENT STYLUS:
15 degrees
From
6.6
cm/sec.
Nominally over
Within
47,000
720
630
Replacement
ELLIPTICAL SHAPED DIAMOND TIP
.0007 inch (17.8 microns) frontal radius
.0010 inch
.0002
~~~~~~ta,
1%
DATA
GAUD-A-M ATICB
15'
STEREO DYNETIC
PHONOGRAPH CARTRIDGE
HEAD ASSEMBLY
M8OE-D, AND M80E-Dl9
20
to
20,000
cps
millivolts per channel
25
2
db of each other
ohm (per channel)
millihenries
ohms
:
Grip Color-yellow
(25.4
of contact with groove.
inch
(5
microns) side contact radii
1
25.0
x
10-6 cm/dyne at
grams maximum
N55E
at
db
at
1,000 cps
microns) between points
SHEET
1,000
cps at
5
26.7"
C.
.I
Models M80E. MSOE-D and MXOE-Dl9 are high quality ellipticalstylus stereo phono cartridges mounted in
suspension system to provide
ture to the operation of an automatic turntable. The Model M80E
is designed specifically for the Garrard Lab
automatic turntables. The Model MXOE-D is designed speci-
m
ca y for the Dual 1009 Automatic Turntable. The Model
D19
is
designed speciflcally for The Dual 1019 Automatic Turn-
table and other Dual models utilizing the 1019 arm and shell.
The new elliptical stylus cartridges are spring .mounted in
pickup heads
of
force
in excess of approximately
safety bumper
in the stylus grip to come in contact with the record surface and
thereby protect the record from needle scratches and protect the
needle itself from damage.
Perhaps the most desirable advantage of all
M80
Series makes it possible to operate the turntable in situations
where
adverse conditions
where modern dancing is done;
which shaky floors
the changer cartridge to mistrack.
in such
1% grams to be exerted on the face
at
the rear of the cartridge
a
changer normally will not work well. These include such
as
or
a
scratch-proof, bounce-proof, fea-
a
manner that permit a maximum needle
2
grams will cause either the plastic
aboard a shi during a storm. in rooms
unstable phonograph supports have caused
an$
a
retractile safety
80
of
the record. Forces
or
the plastic bumper
is
the fact that the
in general, in
and type A70
MXOE-
ahy
area in
I
/
,)
For
INSTALLATION
Automatic and Manual Play:
1.
Remove present pickup head and insert Shure Model into
phono arm. Care must be taken in removal and inserting of
the pickup head? not to cause damage to the stylus,
disturb the position of the leads.
2.
Set stylus force indicator to
3.
Balance arm as per Garrard
stylus force indicator in the range of
In this case, the clearance from the record surface to the
plastic safety bumper
between
tion should be maintained even if
1%
necessary due to the tolerance buildup in certain arms plus
slight inaccuracies in the arm-balancing process.
NOTE:
ance of the safety bumper should be &sured with
records on the turntable.
CAUTION:
is
extremely important in maintaining proper tracking force and
proper operation of the cartridge-head assembly. The leads have
been positioned
leads should not be disturbed.
S
lid’
to.
%”.
This range in recommended playing posi-
gram setting on the arm indicator slightly. .This may be
If it is desired
The position. of the leads inside the pickup head shell
to
at
the factory for optimum performance and the
MODEL MBOE
“0.”
or
Dual instructions and set
1%
to
1%
at
the rear
play a stack of&x records, the clear-
TO
+
of
the cartridge will be
,it
is
necessary to adjust the
2
y
or
grams.
THREE
to
MODEL MBOE-D MODEL MBOE-D19
RECOMMENDED PLAYING POSITIONS
Guarantee
The Stereo Dynetic Head Assemblies and Stereo Dynetic Styli
are guaranteed
for one year from the date of shipment from the factory provided
all instructions are complied with fully. The Guarante; does not
cover stylus wear, no? does it cover damage to the stylus assembly from abuse or mishandling.
Shure Dynetic Styli will withstand long continued usage.
ever, if stylus assembly should be dadaged due to accidental
mishandling-. and diamond tiD
assembly
formance standards at
enclose a check for the service charge with the returned assem-
bW.)
Return Stylus to:
1)’
PATENT NOTICE:
3,077,521,
Copyright
27A423
(9-66)
to
be free from electrical and mechanical defects
Service ~rotet~~on-~cc~dental
is
to
the factory for servicing and testing to original per-
.,
(1
and
3,077,522.
1966
a
nominal service charge of
Service Department
a
SHURE BROTHERS, IN%.
222
Hartrey Avenue
EVANSTON,
Manufactured under
Other patents pending.
Shure Brothers, Inc.
still intact. return the stvlus
ILLINOIS
60204
U:S.
Damage
$6.00.
U.S.A.
Patents
Printed
3,055,988.
in U.S.A.
How-
(Please
Loading...