Shure M80E User Guide
222
HARTREY
AVE
EVANSTON.
ILL.
(60204)
U.S.A.
MODEL
AREA CODE
M80E
312/320-9000
DATA
CABLE
SHEET
SHUfEMlCRO
GARD-A-M ATICO
STEREO DYNETIC
PHONOGRAPH CARTRIDGE
HEAD ASSEMBLY
SPECIFICATIONS
MODELS M8QE,
FREQUENCY
RESPONSE:
OUTPUT VOLTAGE:
CHANNEL
SEPARATION:
CHANNEL
BALANCE:
RECOMMENDED
LOAD IMPEDANCE:
INDUCTANCE:
D.C. RESISTANCE:
STYLUS MODEL
N55E:
COMPLIANCE:
TRACKING FORCE:
REPLACEMENT STYLUS:
Models M80E, MSOE-D an,d M80E-Dl9 are high quality ellipticalstylus stereo phono cartridges mounted in
suspension system to provide
ture to the operation of an automatic turntable. The Model M80E
is designed saeciflcallv for the Garrard Lab 80 and twe
series automath turntgbles. The Model MSOE-D
flcall for the Dual 1009 Automatic Turntable. The Model
D19
rs
designed speciflcally for The Dual 1019 Automatic Turn-
table and the Dual
The new elIiptica1‘ stylus cartridges
pickup heads in such
force of 1% grams to be exerted on the face
in excess of approximately
safety bumper
in the stylus grip to come in contact with the record surface and
thereby protect the record from needle scratches and protect the
needle itself from damage.
Perhaps the most desirable advantage
M80 Series makes
a
where
adverse conditions as aboard
where modern dancing
which shaky floors or unstable phonograph suppbrts have caused
the changer cartridge to mistrack.
~~~!~~tal
1009SK
at
the rear of the cartridge or the plastic bumper
changer normally will not work well. These include such
it
M8QE-D,
From
20
6.6
millivolts per channel at 1,000
to
AND
20,000
M80LD19
Hz.
Hz.
at
cm/sec.
25
db
at
1,000
Nominally over
Within 2 db
47,000
ohm (per channel)
of
each other
Hz.
720 millihenries
630
ohms
Replacement
ELLIPTICAL SHAPED DIAMOND
,0007
.0010 inch
.0002
:
Grip Color-yellow
inch (17.8 microns) frontal radius
(25.4
microns) between points
of contact with groove.
inch
(5
microns) side contact radii
1
25.0
x
10-6
cm/dyne at
TIP
26.7O
C.
1% grams maximum
N55E
a
a
scratch-proof, bounce-proof,
retractile safety
is
design6d speci-
M80E-
fea-
A70
Automatic Turntable.
are
a
manner that permit a maximum needle
2
grams will cause either the plastic
possible to operate the turntable in situations
a
is
ship during a storm. in rooms
done; and, In general in $ny area in
spring mounted in
of
the record. Forces
of
all
is
the fact .that, the
INSTALLATION
For Automatic and Manual Play:
1.
Remove present pickup head and insert Shure Model into
phono arm. Care must be taken in removal and inserting
the pickup heads not to cause damage to the stylus,
disturb the position of the lea.&.
2.
Set stylus force indicator to
3.
Balance arm
stylus force indicator in the range of 1%
In this case, the clearance from the record surface to the
plastic safety bumper
between
tion should be maintained even
1% gram setting on the arm indicator slightly. This may be
necessary due to the tolerance buildup in certain arms plus
slight inaccuracies in the arm-balancinr mocess.
I
NOTE:
If
ance of the safety bumper should be measured with
records on the turntable.
as
per Garrard or Dual instructions and set
%,j“
to.
%”.
This range in recommended playing posi-
it
is desired to play a stack
Suggestions
To clean the stylus, use a camel’s-hair brush
smaller) dipped lightly in alcohol. The alcohol will remove any
sludge deposits which may have coated the stylus tip. The brush
bristles should be trimmed to
Always
brush the stylus with a forward movement from the rear
(terminal end of the cartridge) to the front. Never brush
the stylus from front to back or side
“0.”
to
1% grams.
at
the rear of the cartridge will
if
it
is
necessary to adjust the
-
--
of
five records, the clear-
for
Cleaning
a
Your
Stylus
length no longer than
to
side.
(No.
or
THREE
2
size or
y4
inch.
or
be
of
to
5
CAUTION:
is
extremely important in maintaining proper tracking force and
proper operation
been positioned
leads should not be disturbed.
SPECIAL NOTE:
tridges
performance standards of your cartridge, be certain that any
placement stylus you buy bears the following certiflcation
package
by Shure Brothers, Inc.
Avoid inferior imitations. They will seriously degrade the performance
manufactured by Shure Brothers, Inc.
The position
at
is
the most critical component, To maintain the original
:
“This Stereo Dynetic stylus
of
your cartridge. All genuine “Dynetic” styli are
Lh
TO+
MODEL M80E-D MODEL M80E-DI9
RECOMMENDED PLAYING POSITIONS
of
the leads inside the pickup head shell
of
the cartridge-head assembly. The leads have
the factory
The Dynetic stylus assembly used in these car-
MODEL M80E
t&,TO$
?=--
for
optimum performance and the
is
precision manufactured
SAFETY
on
re-
the
CONCLUSION:
we cannot guarantee
cartridges will meet the published Shure specifications. Accept
substitute.
The Stereo Dynetic Head Assemblies and Stereo Dynetic Styli
are guaranteed to be free from electrical and mechanical defects
for
one year from the date
all instructions
cover stylus wear, nor 8,es
bly from abuse
Shure Dynetic Styli will withstand long, continued usage.
ever,
if
mishandling. and diamond
assembly
formance standards at a nominal service charge
orice
is
Please enclose a check for the
assembly.
Return Stylus to:
PATENT NOTICE:
3,077,621,
Copyright
27A425 (1-68)
Obvious1
if
any
t&t
imitation Dynetic Stylus
the performance, of Shure Dynetid
is
used
no
Guarantee
of
are
com lied with fully. The Guarantel does not
or
mishandling.
Service Prolection-Accidental Damaae
stylus assembly should be damaged due to accidental
to
the factory for se‘rvicing and testing to oricinal
anlv aoolicahle whpn the
and
1966
Manufactured under
3,077,522.
Shure Brothers, Inc. Printed in
shipment from the factory provided
it
cover damage
to
the stylus assem-
--
ti^
is
still intact. return the stvlus
custnmep
service
charge with the returned
In Canada return stylus to:
A.
‘C. Simmonds and Sons, Ltd.
285
Yorkland Boulevard
Agincourt, Ontario
Canada
Other patents pending.
U.S.
rrtur
Patents
of
How-
I
8,056,988
U.S.A.
her-
Loading...