152.4 m (500 ft), minimum, under typical conditions; 487.6 m(1600 ft ) line of sight
NOTE: Actual working range depends on RF signal absorption, reflection and
interference
Audio Frequency Response
50 to 15,000 Hz, ±2 dB. NOTE: Overall system frequency response depends on the
microphone element
Gain Adjustment Range
U1: 0 to 40 dB
U2: 0 to 26 dB
Modulation
±40kHz deviation compressor-expander system with pre-and de-emphasis
RF Power Output
U1, U2: 10 mW maximum
Dynamic Range
>102 dB, A-weighted
RF Sensitivity
U4SU4D
–110 dBm
12 dB SINAD
–105 dBm
30 dB SINAD
Image Rejection
90 dB typical
Spurious Rejection
75 dB typical
Ultimate Quieting (ref. 45 kHz deviation)
>100 dB, A-weighted
Audio Polarity
Positive pressure on microphone diaphragm (or positive voltage applied to tip of
WA302 phone plug) p roduces p ositive voltage o n p in 2 w ith r espect to pin 3 o f l ow
impedance output and the tip of the high impedance
System Distortion(ref. ±45 kHz deviation, 1 kHz modulation)
0.3% Total Harmonic Distortion typical
Power Requirements
U1, U2: 1.5V AA alkaline battery (Duracell MN1500 recommended); Nicad optional
U4: 90 to 230 Vac , 50/60 Hz
Power Consumption: 9.6 W min., 13.2 W max. (U4S)
12 W min.,16 W max. (U4D)
15 W min., 16 W max. (UA840)
Battery Life (Typical)
12 hours (with Duracell MN1500 1.5V AA alkaline battery)
Operating Temperature Range
-20° to 50° C (-4° to 122° F) NOTE: Battery characteristics may limit this range
–107 dBm
12 dB SINAD
–102 dBm
30 dB SINAD
1
/4-inch output
2
Overall Dimensions
U1: 92.2 mm L x 64.7 mm W x 24.2 mm D (3–29/32 x 2–35/64 x 61/64 in.)
U2/58:254 mm L x 50.8 mm Dia. (10 x 2 in.)
U2/BETA 58: 254 mm L x 53.2 mm Dia. (10 x 2–3/32 in.)
U2/87:228.6 mm x 49.2 mm Dia. (9 x 1–15/16 in.)
U2/BETA 87: 216 mm L x 50.8 mm Dia. (8–1/2 x 2 in.)
U4S/U4D: 44.5 mm H x 482.6 mm W x 295.3 mm D (1–3/4 x 19 x 11–5/8 in.)
Net Weight
U1: 175.2 g (6.1 oz.) without battery
U2/58, U2/BETA 58: 375.6 g (13.2 oz.) without battery
U2/87, U2/BETA 87: 303.1 g (10.7 oz) without battery
U4S: 3.30 kg (7.27 lbs)
U4D: 3.85 kg (8.48 lbs)
Certification
U1, U2: EMC Approved to ETS 300 445. RA T ype Approved in the U.K. to MPT1350.
U4S, U4D: VDE Certified to EN 60 950. EMC Approved to ETS 300 445. Meets Low
Voltage Directive.
UHF Type Approved and EMC Approved systems are eligible to carry the CE
marking.
U1 Transmitter Input (Figure 1)
Connector:
Input Configuration:
Actual Impedance:
Maximum Input Level:
6 Vp–p (+7 dBV) for 1% THD at minimum gain
Switchcraft TA4F Tini Q.G. or
LEMO connector (optional)
Unbalanced, active
18 kΩ with lavalier microphone
1 MΩ with instrument cable
setting using 1 kHz signal.
Pin 1: Tied to Ground
TA4F Tini Q.G. Connector Pin
Assignments:
Pin 4: Tied thru 20kΩ Resistor to Ground.
Pin 2: Tied to +5 V
Pin 3: Tied to Audio
(On instrument adapter cable, Pin 4 floats)
Pin 1: Tied to Pin 3 and 10 kΩ to Ground
LEMO Connector
Pin Assignments:
Pin 2: +5V
Pin 3: Tied to Pin 1
Pin 4: Tied to Shield (Ground for Positive Bias)
Voltage for Remote Power:
+5 V supplied to microphone cartridge
U1 Transmitter Output
Connector:
Actual Impedance:
Nominal Output Level:
Maximum Output Level:
Pin Assignments:
SMC
50 Ω
+10 dBm
+11 dBm
Shell = Ground
Center = Signal
3
MICROPHONE
ELEMENT
NOTE: LAVALIER MIC TIES PINS 3 AND 4
TOGETHER; GUITAR CABLE DOES NOT.
U1 MIC JACK BOARD
2
2
4
4
500 Ω
3
3
1
U1L (LEMO 4 PIN) MIC JACK BOARD
1
500 Ω
27 pF
20K Ω
27 pF
+5 V
AUDIO
GROUN
D
1
2
10K Ω
3
4
499 Ω
499 Ω
AUDIO
27 pF
BIAS
27 pF
SHIELD
FIGURE 1
U2 Transmitter Input
Input Configuration:Unbalanced, active
Actual Impedance:20 kΩ
Maximum Input Level:3 Vp–p (0.5 dBV) for 1% THD at minimum gain
setting using 1 kHz signal.
U2 Transmitter Output
Connector:
Actual Impedance:
Nominal Output Level:
Maximum Output Level:
Pin Assignments:
SMC
50 Ω
+10 dBm
+11 dBm
Shell = Ground
Center = Signal
4
U4S and U4D Receiver Input
Connector:AntennaPower InputNetwork Interface
Connector Type:BNCIEC25–Pin D
Actual
50 Ω––––
Impedance:
Nominal Input
Level:
Maximum Input
Level:
–95 to –30 dBm90–230 VAC,
50/60 Hz
+6 dBm
230 VAC, 50/60 Hz––
(–20 dBm
CMOS Logic
recommended)
Pin Assignments:Shell = Ground
IEC Standard––
Center = Signal
Voltage for
Remote Power:
12 Vdc, 150 mA
maximum
––5V, 700 mA max.
U4S and U4D Receiver Output
Connector:MonitorPower
Output
Configuration:
Actual
Impedance:
Nominal
Input Level:
Pin
Assignments:
Unbalanced
mono, 1/4 inch
300 Ω––1 kΩ30 ΩSee
––90 to 230
Tip = Hot
Ring = Hot
Output
––Un-
VAC, 5A
IEC
Standard
Sleeve = Gnd
Voltage/
Current/
Phantom
Power
Protection?
*Output Level: Microphone Level = Line Level – 30 dB
The following tables list groups of frequencies in megahertz. Please note that
only frequencies in Group 1 are compatible.
Group 1 contains 10 compatible frequencies which are derived from a
combination of fixed site (”Multi UHF High and Low”) frequencies as well as
”Indoor Use at Fixed Site” frequencies.
NOTE: See also the additional compatible frequency sets for Group 1.
Group 2 contains 14 fixed site frequencies taken entirely from the Multi UHF
High and Low band.
Groups 3 and 4 contains all frequencies within the Indoor Use at Fixed Site
band, in 25 kHz increment steps.
The master list (Groups A1–A3) covers all frequencies in 25 kHz increments
within the 854–862 MHz band.
Shure recommends that you maintain a 500 kHz separation between each
receiver in the U4D dual receiver. Please contact the Shure Customer Service
Department if you need additional information or assistance in frequency selection
and setup.
NOTE: While the Shure U4 receiver may display each ”FREQUENCY” mode for all
frequencies in 2 5 kHz steps within the 854–862 Mhz band, your transmitter only tunes
to legally allowed frequencies within that band.
7
Group 1
CHANGROUP 1
1
2
3
4
5
6
7
8
9
10
854.900
855.900
856.575
857.125
858.025
858.650
859.625
860.400
860.900
861.750
Additional Compatible Frequency Sets for Group 1
In addition to the 10 compatible channels in Group 1, the following additional
compatible frequency sets can be used if interference is encountered when using
Group 1: