SHOWTEC Pixel Bubble 80 MKII User Manual
Pixel Bubble 80 MKII V1
Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
Ordercode: 41094
MANUAL
ENGLISH
Ordercode: 41094
Pixel Bubble 80 MKII
Table of contents
Warning ............................................................................................................................................................................... 2
Safety Instructions ......................................................................................................................................................... 2
Operating Determinations .......................................................................................................................................... 4
Rigging ............................................................................................................................................................................ 4
Connection with the mains ......................................................................................................................................... 5
Return Procedure .......................................................................................................................................................... 5
Claims .............................................................................................................................................................................. 5
Description of the device ................................................................................................................................................. 6
Frontside.......................................................................................................................................................................... 6
Backside.......................................................................................................................................................................... 7
Installation ........................................................................................................................................................................... 8
Set Up and Operation ....................................................................................................................................................... 8
Installation of multiple LED strings............................................................................................................................... 8
Control Modes ............................................................................................................................................................... 9
One Pixel Bubble (Auto Mode) ............................................................................................................................... 9
Multiple Pixel Bubbles (Master/Slave control) ...................................................................................................... 9
Multiple Pixel Bubbles (DMX Control) ...................................................................................................................10
Multiple Pixel Bubbles (ArtNet/KlingNet Control) ...............................................................................................11
Fixture Linking ...............................................................................................................................................................12
Data Cabling ...............................................................................................................................................................12
Control Panel ...............................................................................................................................................................13
Control Mode ..............................................................................................................................................................13
DMX Addressing ..........................................................................................................................................................13
Menu Overview ...........................................................................................................................................................14
Main M e nu O pt i ons ....................................................................................................................................................15
DMX channel mode settings .................................................................................................................................15
1. Auto Mode ............................................................................................................................................................15
2. DMX channel mode settings .............................................................................................................................16
3. DMX Address.........................................................................................................................................................17
4. Softw are Inform ation...........................................................................................................................................17
5. Strip length settings ..............................................................................................................................................17
6. Network Settings ..................................................................................................................................................18
7. Master/Sl ave Mode .............................................................................................................................................18
DMX Channels .............................................................................................................................................................19
8 channe ls .................................................................................................................................................................19
150 channels .............................................................................................................................................................21
225 channels .............................................................................................................................................................22
300 channels .............................................................................................................................................................23
375 channels .............................................................................................................................................................24
450 channels .............................................................................................................................................................25
Connecting to a Network ..............................................................................................................................................26
KlingNet settin gs ..........................................................................................................................................................26
ArtNet settings..............................................................................................................................................................26
How to make a data cable ......................................................................................................................................27
Software for controlling..............................................................................................................................................27
Maintenance ....................................................................................................................................................................28
Troubleshooting................................................................................................................................................................28
No Lig ht .........................................................................................................................................................................28
No Response to DMX..................................................................................................................................................29
Product Specifi ca tion s ....................................................................................................................................................30
Dimensions ........................................................................................................................................................................31
Notes ..................................................................................................................................................................................32
1
Ordercode: 41094
Pixel Bubble 80 MKII
Your shipment includes:
• Showtec Pixel Bubble 80 MKII
• Powercon power cable (1,5 m)
• User manual
• be qualified
• follow the instructions of this manua l
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good co ndition. Notify the dealer immediately and
retai n packing material fo r inspection if any parts appe ar damaged from sh ipping or t he c arton itself
shows signs of mishandling. Save the carton and all packing materials. In the even t that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to th e acc eler ati on
of this decline. Packaged in cluster s, LEDs exhibi t higher operatin g temper a tures than in ideal or singular
optimum conditions. For this reason, when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If im proving the lifesp an is of hig he r pr i o rity, place care in providing for lower
operationa l te mperatures. Thi s may in clu d e cli matic-enviro nm ental and the reduction of over al l
projection intensity.
Safety Instructions
Every person involved with the installation , operation and maintenan c e of this device has to:
Before the initial start-up, pl e ase make sure that there is no damage cau se d by tran spo rtation.
Should there be any, consult your dealer and do not use the devi ce.
To maintain perfect condition and to ensure a safe operation, it is absolut ely necessary for th e user to
follo w t he safety instruct io ns and warning notes contained i n t his manual.
2
Ordercode: 41094
Pixel Bubble 80 MKII
Please consider that damages caused by manual modifications to the d evice are not subject to
warranty.
This device contains no user-servic eable parts. Refer servi cing to qualified technicians only.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
• Never let the power cord come into contact with other cables! Handle the power cord and all
connections wi th the mains with particular caution!
• Never remove warning or informative labels from the unit.
• Never use anything to cover the ground contact.
• Never leave any cables lying around.
• Do not connect this device to a dimmerpack .
• Do not switch the device on and off in short intervals, as this will reduce the device’s life.
• Do not touch the device’s housing bare-handed during its operation (housin g becomes very hot).
Allow the fixture to cool for at least 5 minutes before handlin g .
• Do not shake the device. Avoid brute force when installing or operating the device.
• Only use the device indoors, avoid contact with water or other liquids.
• Only operate the fixture after having checked if the housing is firmly closed and all screws are tightly
fastened.
• Only operate the device after having familiarized with its functions.
• Avoid flames and do not put close to flammable liquids or gases.
• Always hold the fixture by the transport handles.
• Always keep the case closed while operating.
• Always allow a free air space of at least 50 cm around the unit for ventilation.
• Always d isconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord holding it by the plug. Never pull out the plug by tugging the power cord.
• Make sure that the device is not exposed to extreme heat, moisture or dust.
• Make sure that the available voltage is no t higher than stated on the rear panel.
• Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
• If device was drop ped or struc k , disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operatin g.
• If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switc h it on immedi at e ly. The ar is i ng c o nd ensation wate r might damage you r de v ice. Leave the
device switched off until it has reached room temperature.
• If your Showtec devic e fai ls to work properly, discontinue the use immedia tely. Pack the u n it securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
• For adult use only. The fixture must be installed beyond the reach of children. Never leave the unit
running unattended.
• Never attempt to bypass the thermostatic switch or fuses.
• The user is responsible for correct posi tioning and operating of the Pixel Bubble. The manufactu rer will
not accept liability for damages caused by the misuse or incorrec t installation of this device.
• This device falls under protection cla ss I. Therefore it is essential to connect the yellow/green
conductor to earth.
• Repairs, servi cing and electric conn ection must be carried out by a qualified technician.
• WARRANTY: Till one year after date of purchase.
3
Ordercode: 41094
Pixel Bubble 80 MKII
Operating Determinations
• This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
• The minimum distance between light output and the illuminated surface must be bigger than 1
meter.
• The maximum ambient temperature t
• The relative humidity must not exceed 50 % with an ambient temperature of 40° C.
• If this device i s operated in any other way than the one des c ribed in this manual, the produ c t may
suffer damages and the warranty becomes void.
• Any other operation may le ad to dang e rs l ike short-c ircuit , burns, electric shock, cras h, etc.
= 40°C must never be exceeded.
a
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
othe r safety issues.
Do not attempt the installation yourself !
Always let the installation be carried out by an authorized dealer !
Procedure:
• If the fixture is lowered from the ceiling or high joists, professional trussing systems have to be used.
• Use a clamp to mount the fixture, with the mounting bra ck et, to th e trussing system.
• The fixture must never be fixed swingin g freely in the room.
• The installation must alway s be secured with a safety attachment, e.g. an appropriat e sa f ety net or
safety cable.
• When rigging, derigging or servicing the projector, always make sure, that the area below the
installation site is secured and that there are not any unauthorized people around.
4
Ordercode: 41094
Pixel Bubble 80 MKII
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE GROUND
Return Procedure
Connection with the mains
Connect the device to the mains with the power-plug.
Always check if th e righ t color cable is connected to the right place.
Make sure that the device is always properly connected to the earth!
Improper installation can cause serious injuries and/or damage of property!
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products retu rned
without an RMA number will be refused. Highlite will not acce pt t he re t urned goods or an y re s ponsibility.
Call Highlite 0031-455667723 or mail aftersales@highlite.nl
Be prepared to provide the model number, serial number and a brief description of the cause for the
retu rn. Be sure to properly pac k fixture, any shippi ng damage resu lting fro m inadequat e packagin g i s the
customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
produ c t ( s ). As a sugges t i on, prope r UPS packin g or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your na me
02) Your address
03) Your pho ne number
04) A brief description of the symptoms
and reque s t an RMA prior to shi pping the fixtur e .
Claims
The client has the obligation to check the delivered goods immedia tely upon delivery for any shortcomings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to report and submit claims with the shipper in the event that a fixture is
dama g ed due to shipping. Transportation damage has to be reported to us within one day after receipt
of the d elivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
agreed otherwise in writing.
Complaints against us must be prepared in writing or sent by fax within 10 working day s after receipt of
the invoice. After this period complaints wi ll not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement from which the obligation is resul ting.
5
Ordercode: 41094
Pixel Bubble 80 MKII
41095 – 1m strin g for Pixel Bubble 80 MKII
Fig. 01
Description of the device
Features
The Pixel Bubble 80 MKII is a LED visual effect with high outp ut and great e f f e cts.
The set includes 15 x 1-meter long LED strings but it is possible to connect a maximum of 30 LED strings to
the Pixe l Bubble. The Pixel Bubbl e 80 MKII supports the mo s t popular protocol s , su c h as: DMX, ArtNe t and
KlingNet.
• Power Supply: 100-240 VAC, 60/50Hz
• Power Consumption: 90W
• Light source: min. 50 – max. 150 x 5050 SMD RGB LEDs
• Control Protocol: DMX-512, ArtNet, KlingNet
• DMX channels: 8, 150, 225, 300, 375, 450 channels
• Onboard: LCD display for easy setup
• String length: 1 m (5 LEDs per string); maximum setup length : 6 m
• Connectors: Powercon power connector, 3-pin XLR IN/OUT, RJ45 IN/OUT
• Cooling: Convection
• Dimmer: 0-100%
• Strobe: 0-20Hz
• Refresh rate: 444Hz
• Beam angle: 360°
• Housing: Die-cast aluminum
• Dimensions: 1000 x 65 x 73 mm (LxWxH)
• Weight: 5,2 kg
Optional accessories:
41096 – Extensio n cable for Pixel Bubble 80 MKII (43 cm)
41097 – Extensio n cable for Pixel Bubble 80 MKII (100 cm)
You can connect from 2 up to 6 LED strings per output (30 strings in total)
Frontside
01) Safety eye
02) 5050 SMD RGB LEDs
03) LCD display + menu buttons
6
Ordercode: 41094
Pixel Bubble 80 MKII
Fig. 02
Backside
04) Powercon power connector 100-240V OUT
05) 3-pin DMX signal connector IN
06) RJ45 ArtNet/KlingNet conne ctor IN
07) RJ45 ArtNet/KlingNet connec tor OUT
08) 3-pin DMX signal connector OUT
09) Power switch ON/OF F
10) Powercon power connector 100-240V IN
11) Ground/earth connection
7
Ordercode: 41094
Pixel Bubble 80 MKII
Fig. 03
Installation
Remove all packing mater ials from the Pixel Bubble 80 MKII. Check if al l fo am an d pl as t ic padding is
removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not sub ject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operat ion mod e.
Before plugging the unit in, always make sure that the power supply matches the product speci fication
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Conne c t th e device to th e main power supply.
Installation of multiple LED strings
01) It is possible to connect multiple LED strin gs (41095) to the Pixel Bubble 80 MKII.
02) You can connect up to 6 strings per output (30 in total).
03) The number of strings is determined by the Length settings in the main menu.
04) See page 17: Strip length settings, for more information.
8
Ordercode: 41094
Pixel Bubble 80 MKII
There are 3 modes:
• Auto Mode
• Master/Slave
• DMX-512 (8CH, 150CH, 225CH, 300CH, 375CH, 450CH)/ArtNet/KlingNet
The pins:
01) Earth
Multiple Pixel Bubbles (Master /Sl a v e control )
Fig. 04
Control Modes
One Pixel Bubble (Auto Mode)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation .
02) Plug the end of the electric mains power cord in to a proper el e c tr ic power supply socket.
03) When the Pixel Bubble is not connected with a DMX cable, it functions as a stand-alone device.
Please see page 15 for more information about Auto Mode.
Multiple Pixel Bubbles (Master /Sl a v e control )
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Use a 3-pin XLR cable to connect the Pixel Bubbles.
02) Signal -
03) Signal +
03) Link the un its as shown i n f ig. 04. Connect the first unit's DMX "out" socket with th e second unit's "in "
socket, using a DMX-signal cable. Repeat this process to link the second, third , and fourth units.
04) You can use the same functions on the master device as described on page 15 (Auto Mode).
This means that you can set your desired operation mode on the master device and all slave
devices will react the same as the master device.
9
Ordercode: 41094
Pixel Bubble 80 MKII
Multiple Pixel Bubbles DMX Set Up
Fig. 05
Multiple Pixel Bubbles (DMX Control)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation .
02) Always use a safety cable (ordercode 70140 / 70141).
03) Use a 3-pin XLR cable to connect the Pixel Bubbles and other devices.
04) Link the units as shown in fig. 05. Connect the first unit's DMX "out" socket with the second unit's "in"
socket, using a DMX signal cable. Repeat this process to link the second, third , and fourth units.
05) Supply electric power: Plug electric mains po wer cords into each unit's Powercon socket, then plug
the other end of the mains power cord into proper electric power supply so cket s, startin g wi th the
first unit. Do not supply power before the whole system is set up and connected properly.
10
Note : Link all cables b efor e conn ect in g elec tri c p ower
Loading...