SHOWTEC FX Shot MK II User Manual
FX Shot MKII V1
Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
Ordercode: 60906
MANUAL
ENGLISH
1
Ordercode: 60906
FX Shot MKII
Table of contents
Warning ............................................................................................................................................................................... 2
Unpacking Instructions ................................................................................................................................................. 2
Safety Instructions ......................................................................................................................................................... 2
Operating Determinations .......................................................................................................................................... 4
Rigging ............................................................................................................................................................................ 5
Connection with the mains......................................................................................................................................... 5
Return Procedure .......................................................................................................................................................... 6
Claims .............................................................................................................................................................................. 6
Description of the device ................................................................................................................................................. 7
Overview ........................................................................................................................................................................ 7
Optional accessories.................................................................................................................................................... 8
Installation .........................................................................................................................................................................10
Testing ................................................................................................................................................................................13
Set Up and Operation .....................................................................................................................................................14
Setup 1 ..........................................................................................................................................................................14
Setup 2 ..........................................................................................................................................................................15
Disconnection .............................................................................................................................................................15
Maintenance ....................................................................................................................................................................16
Troubleshooting ...............................................................................................................................................................16
No blue LED Indicator ................................................................................................................................................16
No Response to DMX from your controller .............................................................................................................16
Product Specification .....................................................................................................................................................17
Dimensions ........................................................................................................................................................................18
2
Ordercode: 60906
FX Shot MKII
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
● Showtec FX Shot with Neutrik power cable (1,5 m)
● User manual
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
● be authorized
● follow the instructions of this manual
● We also insist that all new users (operators, installers, maintenance workers and cleaners) receive a
training course during which they become thoroughly familiarized with this user manual.
3
Ordercode: 60906
FX Shot MKII
Before your initial start-up, please make sure that there is no damage caused by transportation. Should
there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
● Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
● Never remove warning or informative labels from the unit and, on regular basis, make sure that they
remain clearly visible and legible.
● Never place any material over the cannon tube.
● Never use anything to cover the ground contact.
● Never use the device during thunderstorms, unplug the device immediately.
● Never look directly into the cannon tube.
● Never leave any cables lying around.
● Never replace parts by yourself.
● Do not open the device and do not modify the device.
● Do not insert objects into air vents.
● Do not expose the device to any source of vibration.
● Do not insert objects into the cannon tube.
● Do not switch the device on and off in short intervals, as this would reduce the device’s life.
● Do not touch the FX Shot while working or if it is connected to the mains power. Even if the FX Shot is
not in operation, the electric cannons can still be filled and cause harm.
● Do not remove or disable the safety devices.
● Do not shake the device. Avoid brute force when installing or operating the device. The FX Shot
reacts very sensitive to movement.
● All required safety equipment must be in good condition and must be working properly.
● Use the device ONLY if there ARE NOT ANY people, animals or other objects in the direction of the
output within the output range. The shooting direction is the direction in which the output pipe on
the FX Shot is pointed.
● Only use the device indoors, avoid contact with water or other liquids.
● Only operate the fixture after having checked that the housing is firmly closed and all screws are
tightly fastened.
● Only use the FX Shot according to the instructions in this manual.
● Only operate the device after having familiarized with its functions.
● Avoid flames and do not put close to flammable liquids or gases.
● Always allow free air space of at least 50 cm around the unit for ventilation.
● Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord by the plug. Never pull out the plug by tugging the power cord.
● Always keep the workplace clean and provide adequate ambient lighting.
● Make sure that the device is not exposed to extreme heat, moisture or dust.
● Make sure that the available voltage is not higher than stated on the rear panel.
● Make sure that all the required safety devices are in good condition and function properly.
● Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
● If text and/or icons are missing, damaged or illegible on the FX Shot, they should be replaced.
● If the cannon tube is obviously damaged, it needs to be replaced, so that its functions are not
impaired.
● If the device is dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
4
Ordercode: 60906
FX Shot MKII
● If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
● If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
● For adult use only. Device must be installed out of the reach of children and unauthorized persons.
Never leave the unit running unattended.
● Never attempt to bypass the thermostatic switch or fuses.
● For replacement use fuses of same type and rating only.
● Provide sufficient lighting of the surroundings, when operating the FX Shot.
● The FX Shot may only be used if there are no persons, animals or other objects in the direct “line of
fire” of the electric cannon within the output distance. The shooting direction is the direction, in
which the electric cannon of the FX Shot is pointing. The output distance is dependent on the
content and length of the electric cannons.
● The user is responsible for correct positioning and operating of the FX Shot. The manufacturer will not
accept liability for unsafe situations, accidents, damages caused by:
- The misuse or incorrect installation of this device.
- Ignoring warnings or instructions as shown in this manual.
- Using the FX Shot for purposes or conditions other than specified in this manual.
- Changes to the FX Shot. This includes the use of other than original spare parts.
- Inadequate maintenance.
- The unauthorized removal of safety covers and / or guards.
- The improper use of the FX Shot.
● This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
● Repairs, servicing and electric connection must be carried out by a qualified technician.
● WARRANTY: Till one year after date of purchase.
Operating Determinations
● This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
● The maximum ambient temperature ta = 35°C must never be exceeded.
● Do not expose this device to relative humidity degree higher than 75%.
● Do not expose this device to any source of vibration.
● Operate the device in a reasonably stable temperature of between 0 and 35ºC
● If this device is operated in any other way, than the one described in this manual, the product may
suffer damages and the warranty becomes void.
● If any unauthorized alterations or repairments are performed on the device, the warranty becomes
void.
● Any operation different to the ones described in this manual may lead to dangers like frostbite,
short-circuit, burns, electric shock, crash etc.
5
Ordercode: 60906
FX Shot MKII
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself !
Always let the installation be carried out by an authorized dealer !
Procedure:
● If the FX Shot is lowered from the ceiling or high joists, professional trussing systems have to be used.
● Use a clamp to mount the FX Shot, with the mounting bracket, to the trussing system.
● The FX Shot must never be fixed swinging freely in the room.
● The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety cable.
● When rigging, derigging or servicing the FX Shot, always make sure, that the area below the
installation place is blocked and staying in the area is forbidden.
We presume that you, your employees and others who come into contact with the FX Shot
are familiar with how the machine must be dealt with. This includes the correct use,
maintenance and repair of the FX Shot as described in this user manual. The employees
should be familiar with the use of the device through training and/or experience.
Showtec excludes liability for unsafe situations, accidents and damage that are the result of:
● Disregard for the warnings or regulations as set out on the FX Shot or in this manual.
● Use for other purposes or under other circumstances than those set out in this documentation.
● Alterations to the FX Shot. This also includes the use of replacement parts other than the original ones.
● Insufficient maintenance.
● Unauthorised removal of safety caps and/or safeguards.
● Incompetent operation of the machine.
Showtec is not liable for any consequential loss in the event of an FX Shot breakdown.
This user manual has been drawn up with the utmost care. Showtec cannot be held responsible for any
mistakes made in this publication or for any consequences thereof.
Connection with the mains
Connect the device to the mains with the power-plug.
Always pay attention, that the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE GROUND
Make sure that the device is always connected properly to the earth!
Improper installation can cause serious damage to people and property!
Loading...