Page 1
Expression 8000 Spot V1
Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
Ordercode: 41391
MANUAL
ENGLISH
Page 2
Ordercode: 41391
Expression 8000 Spot
Table of contents
Warning ............................................................................................................................................................................... 3
Safety Instructions ......................................................................................................................................................... 3
Operating Determinations .......................................................................................................................................... 5
Rigging ............................................................................................................................................................................ 5
Connection with the mains......................................................................................................................................... 6
Return Procedure .......................................................................................................................................................... 7
Claims .............................................................................................................................................................................. 7
Description of the device ................................................................................................................................................. 8
Frontside.......................................................................................................................................................................... 8
Backside ......................................................................................................................................................................... 9
Installation ........................................................................................................................................................................... 9
Set Up and Operation ....................................................................................................................................................... 9
Control Modes .............................................................................................................................................................10
One Expression (Auto and Manual) .....................................................................................................................10
Multiple Expressions (Master/Slave control) ........................................................................................................10
Multiple Expressions (DMX Control) ......................................................................................................................11
Fixture Linking ...............................................................................................................................................................12
Data Cabling ...............................................................................................................................................................12
Control Panel ...............................................................................................................................................................13
Control Mode ..............................................................................................................................................................13
DMX Addressing ..........................................................................................................................................................13
Main Menu Options ....................................................................................................................................................14
1. Address ..................................................................................................................................................................14
2. Personality .............................................................................................................................................................15
3. Control modes .....................................................................................................................................................15
4. Options ..................................................................................................................................................................16
4.1. Pan/Tilt ................................................................................................................................................................16
4.1.1. Pan Invert ........................................................................................................................................................16
4.1.2. Tilt Invert ...........................................................................................................................................................16
4.1.3. Pan/Tilt Speed ................................................................................................................................................16
4.1.4. Pan/Tilt Range ................................................................................................................................................17
4.2. Blackout .............................................................................................................................................................17
4.3. Display lock ........................................................................................................................................................17
4.4. Display ................................................................................................................................................................17
4.5. Dimming curves ................................................................................................................................................17
4.6. DMX error ...........................................................................................................................................................17
4.7. Fan speed ..........................................................................................................................................................18
4.8. Setting .................................................................................................................................................................18
4.8.1. Set default ......................................................................................................................................................18
4.8.2. User record .....................................................................................................................................................18
4.8.3. Wireless DMX menu .......................................................................................................................................18
4.9. Wireless DMX settings .......................................................................................................................................18
4.9.1. WDMX active .................................................................................................................................................18
4.9.2. WDMX reset ....................................................................................................................................................18
5. Manual mode ......................................................................................................................................................19
5.1. Channel ..............................................................................................................................................................19
5.2. Edit .......................................................................................................................................................................20
5.3. Reset ...................................................................................................................................................................20
5.4. Upload ................................................................................................................................................................20
5.5. Performance test ..............................................................................................................................................21
6. System information ..............................................................................................................................................21
DMX Channels .............................................................................................................................................................22
23 channels (PERSON1) ..........................................................................................................................................22
17 channels (PERSON2) ..........................................................................................................................................26
1
Page 3
Ordercode: 41391
Expression 8000 Spot
Maintenance ....................................................................................................................................................................31
Replacing the Fuse .....................................................................................................................................................31
Gobo Size .....................................................................................................................................................................32
Replacing a gobo from the rotating gobo wheel ...............................................................................................32
Glass Gobo Orientation .............................................................................................................................................33
Rotating/Static Gobo wheels and Color wheels .......................................................................................................34
Troubleshooting ...............................................................................................................................................................34
No Light .........................................................................................................................................................................34
No Response to DMX..................................................................................................................................................35
Product Specifications ....................................................................................................................................................36
Dimensions ........................................................................................................................................................................37
Notes ..................................................................................................................................................................................38
2
Page 4
Ordercode: 41391
Expression 8000 Spot
Your shipment includes:
● Showtec Expression 8000 Spot
● PowerCON power cable (1,5 m)
● 2 mounting brackets with quick-locks
● User manual
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason, when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving the lifespan is of higher priority, place care in providing for lower
operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity.
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
• be qualified
• follow the instructions of this manual
3
Page 5
Ordercode: 41391
Expression 8000 Spot
Before the initial start-up, please make sure that there is no damage caused by transportation.
Should there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes contained in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
• Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
• Never remove warning or informative labels from the unit.
• Never use anything to cover the ground contact.
• Never lift the fixture holding it by the projector-head, as the mechanics may be damaged. Always
hold the fixture by the transport handles.
• Never place any material over the lens.
• Never look directly into the light source.
• Never leave any cables lying around.
• Never loosen the screws of the rotating gobo otherwise you risk opening of the ball bearing.
• Do not insert objects into air vents.
• Do not connect this device to a dimmerpack.
• Do not switch the device on and off in short intervals, as this will reduce the device’s life.
• Do not touch the device’s housing bare-handed during its operation (housing becomes hot). Allow
the fixture to cool for at least 5 minutes before handling.
• Do not shake the device. Avoid brute force when installing or operating the device.
• Only use the device indoors, avoid contact with water or other liquids.
• Only operate the fixture after having checked if the housing is firmly closed and all screws are tightly
fastened.
• Only operate the device after having familiarized with its functions.
• Avoid flames and do not put close to flammable liquids or gases.
• Always keep the case closed while operating.
• Always allow a free air space of at least 50 cm around the unit for ventilation.
• Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord holding it by the plug. Never pull out the plug by tugging the power cord.
• Make sure that the device is not exposed to extreme heat, moisture or dust.
• Make sure that the available voltage is not higher than stated on the rear panel.
• Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
• If the lens is obviously damaged, it has to be replaced.
• If device was dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
• If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
• If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
• For adult use only. Moving head must be installed beyond the reach of children. Never leave the unit
running unattended.
• Never attempt to bypass the thermostatic switch or fuses.
• For replacement use fuses of same type and rating only.
4
Page 6
Ordercode: 41391
Expression 8000 Spot
• The user is responsible for correct positioning and operating of the Expression. The manufacturer will
not accept liability for damages caused by the misuse or incorrect installation of this device.
• This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
• Repairs, servicing and electric connection must be carried out by a qualified technician.
• WARRANTY: Till one year after date of purchase.
Operating Determinations
• This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
• The minimum distance between light output and the illuminated surface must be bigger than 12
meters.
• The maximum ambient temperature t
• The relative humidity must not exceed 50 % with an ambient temperature of 40° C.
• If this device is operated in any other way than the one described in this manual, the product may
suffer damages and the warranty becomes void.
• Any other operation may lead to dangers like short-circuit, burns, electric shock, crash, etc.
= 40°C must never be exceeded.
a
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself !
Always let the installation be carried out by an authorized dealer !
Procedure:
• If the projector is lowered from the ceiling or high joists, professional trussing systems have to be used.
• Use a clamp to mount the projector, with the mounting bracket, to the trussing system.
• The projector must never be fixed swinging freely in the room.
• The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety cable.
• When rigging, derigging or servicing the projector, always make sure, that the area below the
installation site is secured and that there are not any unauthorized people around.
5
Page 7
Ordercode: 41391
Expression 8000 Spot
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE GROUND
The Expression can be placed on a flat stage floor or mounted to any kind of truss with a clamp.
Improper installation can cause serious injuries and/or damage of property!
Connection with the mains
Connect the device to the mains with the power-plug.
Always check if the right color cable is connected to the right place.
Make sure that the device is always properly connected to the earth!
Improper installation can cause serious injuries and/or damage of property!
6
Page 8
Ordercode: 41391
Expression 8000 Spot
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail aftersales@highlite.nl and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause for the
return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the
customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name
02) Your address
03) Your phone number
04) A brief description of the symptoms
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any shortcomings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to report and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
agreed otherwise in writing.
Complaints against us must be prepared in writing or sent by fax within 10 working days after receipt of
the invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement from which the obligation is resulting.
7
Page 9
Ordercode: 41391
Expression 8000 Spot
Fig. 01
Description of the device
Features
The Expression 8000 Spot is a moving head with high output and great effects.
Input voltage: 100-240V, 60/50Hz
Power consumption: 280W
Light source: 230W LED module
Lumen: 8000 lumen
Peak intensity: 160000cd
DMX channels: 17 or 23 channels
LCD display for easy setup
Control modes: Auto, Manual, Master/Slave, DMX-512
Control protocol: DMX-512
Motorized iris and focus
Dimmer: 0-100%
Zoom: 13-35°
Strobe: 0-20Hz
Pan: 540°
Tilt: 270°
3-facet rotating prism
7 rotating gobos and 11 static gobos
2 color wheels: 7 dichroic filters + white per wheel
Housing: Metal & Flame retardant plastic
Connections: 3-pin/5-pin XLR data connectors & PowerCON to Schuko power connector
IP rating: IP20
Fuse: T6,3AL/250V
Dimensions: 450 x 390 x 640 mm (LxWxH)
Weight: 26 kg
Frontside
01) LED Lens
02) LCD display + menu buttons
8
Page 10
Ordercode: 41391
Expression 8000 Spot
Backside
Fig. 02
03) Fuse T6,3AL/250V
04) Power switch ON/OFF
05) 5-pin DMX signal connector IN
06) 5-pin DMX signal connector OUT
07) 3-pin DMX signal connector OUT
08) 3-pin DMX signal connector IN
09) PowerCON power connector 100-240V OUT
10) PowerCON power connector 100-240V IN
Installation
Remove all packing materials from the Expression 8000 Spot. Check if all foam and plastic padding is
removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Connect the device to the main power supply.
9
Page 11
Ordercode: 41391
Expression 8000 Spot
There are 4 modes:
• Auto
• Manual
• Master/Slave
• DMX-512 (17CH, 23CH)
The pins:
01) Earth
02) Signal -
03) Signal +
Multiple Expressions (Master/Slave control)
Fig. 03
Control Modes
One Expression (Auto and Manual)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Plug the end of the electric mains power cord into a proper electric power supply socket.
03) When the Expression is not connected with a DMX cable, it functions as a stand-alone device.
Please see pages 15 and 19 for more information about the Auto mode and Manual mode.
Multiple Expressions (Master/Slave control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Use a 3-pin/5-pin XLR cable to connect the Expression.
03) Link the units as shown in fig. 03. Connect the first unit's DMX "out" socket with the second unit's "in"
socket, using a DMX-signal cable. Repeat this process to link the second, third, and fourth units.
You can use the same functions on the master device as described on pages 15 and 19 (Auto or
Manual). This means that you can set your desired operation mode on the master device and all
slave devices will react the same as the master device.
10
Page 12
Ordercode: 41391
Expression 8000 Spot
Multiple Expressions DMX Set Up
Fig. 04
Multiple Expressions (DMX Control)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Use a 3-pin/5-pin XLR cable to connect the Expressions and other devices.
04) Link the units as shown in fig. 04. Connect the first unit's DMX "out" socket with the second unit's "in"
socket, using a DMX-signal cable. Repeat this process to link the second, third, and fourth units.
05) Supply electric power: Plug electric mains power cords into each unit's PowerCON socket, then plug
the other end of the mains power cord into proper electric power supply sockets, starting with the
first unit. Do not supply power before the whole system is set up and connected properly.
11
Note : Link all cables before connecting electric power
Page 13
Ordercode: 41391
Expression 8000 Spot
Important:
Fixtures on a serial data link must be daisy-chained in a single line. To comply with the
EIA-485 standard, no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX optically
isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of fixtures on a DMX data link: 30 fixtures
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
Data Cabling
To link fixtures together, you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your own cable,
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio DMX Data Cables
• DAP Audio Basic microphone cable for allround use. bal. XLR/M 3-pin > XLR/F 3-pin.
Ordercode FL01150 (1,5 m), FL013 (3 m), FL016 (6 m), FL0110 (10 m), FL0115 (15 m), FL0120 (20 m).
• DAP Audio X-type data cable XLR/M 3-pin > XLR/F 3-pin. Ordercode FLX0175 (0,75 m),
FLX01150 (1,5 m), FLX013 (3 m), FLX016 (6 m), FLX0110 (10 m).
• DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5 m), FL713 (3 m), FL716 (6 m), FL7110 (10 m).
• DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m), FL7210 (10 m).
• DAP Audio 110 Ohm cable with digital signal transmission. Ordercode FL0975 (0,75 m),
FL09150 (1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m).
12
Page 14
Ordercode: 41391
Expression 8000 Spot
Control Panel
A) LCD display
B) LEFT button
C) UP button
D) OK button
E) RIGHT button
F) DOWN button
Fig. 05
Display Off after 30 seconds
The Expression 8000 Spot can be operated with a controller in control mode or without the controller in
stand-alone mode.
Control Mode
The fixtures are individually addressed on a data-link and connected to the controller.
The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it,
the controller will display the saved DMX address, next time.)
DMX Addressing
The control panel on the front side of the base allows you to assign DMX fixture addresses, which is the first
channel with which the Expression will respond to the controller.
Please note, when you use the controller, the unit has 23 channels.
When using multiple Expressions, make sure you set the DMX addresses right.
Therefore, the DMX address of the first Expression should be 1(001); the DMX address of the second
Expression should be 1+23=24 (024); the DMX address of the third Expression should be 24+23=47 (047),
etc. Please, be sure that you do not have any overlapping channels in order to control each Expression
correctly. If two or more Expressions are addressed similarly, they will work similarly.
Controlling:
After having addressed all Expression fixtures, you may now start operating these via your lighting
controller.
Note: After switching on, the Expression will automatically detect whether DMX 512 data is received or
not. If there is no data received at the DMX-input, the “LED “ on the control panel will not flash.
If not, the problem may be:
• The XLR cable from the controller is not connected with the input of the Expression 8000 Spot.
• The controller is switched off or defective, the cable or connector is detective, or the signal wires are
swapped in the input connector.
Note: It is necessary to insert an XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.
When no button is pressed for 30 seconds, the display will turn off.
To light up the display, you have to press the UP, DOWN, LEFT, RIGHT or OK button.
Once you have pressed the button, the display will light up.
13
Page 15
Ordercode: 41391
Expression 8000 Spot
Main Menu Options
01) On start-up, the device will reset its settings. The following screen will pop up:
02) The display will show a series of screens containing information on the device’s current operating
mode, current software version and current temperature.
03) Press the OK button to enter the main menu. The following screen will pop up:
1. Address
With this menu you can set the device’s starting DMX address.
01) In the main menu, press the UP/DOWN buttons to choose ADDRESS and press the OK button to enter
the menu. The display will show:
02) Press the UP/DOWN buttons to set the desired DMX address. The adjustment range is between 001-
512.
03) Once you have set the DMX address, press the OK button to save changes and return to the main
menu.
14
Page 16
Ordercode: 41391
Expression 8000 Spot
2. Personality
With this menu you can set the device’s personality.
01) In the main menu, press the UP/DOWN buttons to choose PERSON and press the OK button to enter
the menu. The display will show:
02) Press the UP/DOWN buttons to choose one of the 2 personalities:
PERSON1 (23 channels)
PERSON2 (17 channels)
03) Once you have chosen your preferred personality, press the OK button to save changes and return
to the main menu.
3. Control modes
With this menu you can choose the desired operating mode.
01) In the main menu, press the UP/DOWN buttons to choose RUNMODE and press the OK button to
enter the menu. The display will show:
02) Press the UP/DOWN buttons to choose one of the 5 control modes:
DMX-512 (The device will react to user’s DMX input.)
AUTO1 and AUTO2 (built-in programs)
CUSTOM (The device’s behaviour depends on the adjustments made in MANUAL menu, see
page 19.)
SLAVE (The device will react the same as the master device.)
03) Once you have chosen your preferred control mode, press the OK button to confirm.
04) If you have chosen AUTO1 or AUTO2 and pressed the OK button, you will be able to adjust the built-in
program speed.
05) Press the UP/DOWN buttons to adjust the program speed. The adjustment range is between 0-10,
from OFF to fast.
06) Press the OK button to confirm.
15
Page 17
Ordercode: 41391
Expression 8000 Spot
4. Options
With this menu you can adjust the device’s settings.
01) In the main menu, press the UP/DOWN buttons to choose OPTION and press the OK button to enter
the menu. The display will show:
02) Press the UP/DOWN buttons to toggle between the following options:
PAN/TILT
BLACKOUT
DISPLAY LOCK
DISPLAY
DIMx
DMX ERROR
FAN SPEED
SETTING
WIRELESS
03) Once you have chosen your preferred option, press the OK button to proceed to the desired
submenu.
4.1. Pan/Tilt
01) Press the UP/DOWN buttons to choose one of the 4 options:
PAN INVERT
TILT INVERT
P/T SPEED
P/T RANGE
4.1.1. Pan Invert
01) If you have chosen PAN INVERT, press the OK button to proceed to the submenu.
02) Press the UP/DOWN buttons to choose between OFF and ON and press the OK button to confirm.
03) The device will now perform pan inversion.
4.1.2. Tilt Invert
01) If you have chosen TILT INVERT, press the OK button to proceed to the submenu.
02) Press the UP/DOWN buttons to choose between OFF and ON and press the OK button to confirm.
03) The device will now perform tilt inversion.
4.1.3. Pan/Tilt Speed
01) If you have chosen P/T SPEED, press the OK button to proceed to the submenu.
02) Press the UP/DOWN buttons to choose between FAST and NORMAL and press the OK button to adjust
the speed settings.
16
Page 18
Ordercode: 41391
Expression 8000 Spot
4.1.4. Pan/Tilt Range
01) If you have chosen P/T RANGE, press the OK button to proceed to the submenu.
02) Press the RIGHT button to toggle between the following options:
P. START (Pan start point)
P. END (Pan end point)
T. START (Tilt start point)
T. END (Tilt end point)
USE
03) If you have chosen P. START, P. END, T. START or T. END, press the UP/DOWN buttons to adjust the
values. The adjustment range is between 0-255. With those options you can adjust the device’s
pan/tilt movement range.
04) If you have chosen USE, press the UP/DOWN buttons to choose between YES and NO and press the
OK button to confirm. If you have chosen YES, the adjusted movement range settings will be applied.
4.2. Blackout
01) If you have chosen BLACKOUT, press the UP/DOWN buttons to choose between OFF and ON.
02) Press the OK button to confirm your choice.
4.3. Display lock
01) If you have chosen DISPLAY LOCK, press the UP/DOWN buttons to choose between OFF and ON.
02) Press the OK button to confirm your choice.
03) If you have chosen ON, the following screen will pop up on the next start up and/or when the display
turns off if no button is pressed within 30 seconds:
04) Insert the password by pressing the buttons in the following order: UP, DOWN, UP, DOWN and press
the OK button to confirm.
4.4. Display
01) If you have chosen DISPLAY, press the UP/DOWN buttons to choose between OFF and ON.
02) Press the OK button to confirm your choice.
03) If you have chosen ON, the display will remain on. If you have chosen OFF, the display will turn off if
no button is pressed within 30 seconds.
4.5. Dimming curves
01) If you have chosen DIMx, press the UP/DOWN buttons to choose one of the available dimming
curves: DIM1-DIM4.
02) Press the OK button to confirm your choice.
4.6. DMX error
01) If you have chosen DMX ERROR, press the UP/DOWN buttons to choose one of the 2 options:
SAVE (the device will use the last working DMX input)
BLACK (the device will black out its output)
02) Press the OK button to confirm your choice.
17
Page 19
Ordercode: 41391
Expression 8000 Spot
4.7. Fan speed
01) If you have chosen FAN SPEED, press the UP/DOWN buttons to choose one of the 4 options:
SLOW (slow fan)
NORM (normal fan)
FAST (fast fan)
AUTO (speed dependent on the device’s temperature)
02) Press the OK button to confirm your choice.
4.8. Setting
01) If you have chosen SETTING, press the UP/DOWN buttons to choose one of the 3 options:
SET DEFAULT
USER RECORD
WIRELESS HIDE
02) Press the OK button to confirm your choice.
4.8.1. Set default
01) If you have chosen SET DEFAULT, press the OK button to proceed to the submenu.
02) When the display shows SET PRESENT, press the OK button to proceed.
03) Press the UP/DOWN buttons to choose between OFF and ON.
04) Press the OK button to confirm your choice.
05) If you have chosen ON, the device’s settings will be reset.
06) If you have chosen OFF, the device will return to the previous menu.
4.8.2. User record
01) If you have chosen USER RECORD, press the OK button to proceed to the submenu.
02) Press the UP/DOWN buttons to choose between the 2 options:
LOAD RECORD (load preset settings)
SAVE TO RECORD (create a setting preset)
03) Press the OK button to confirm your choice and proceed to the submenu.
04) Press the UP/DOWN buttons to choose between OFF and ON and press the OK button to confirm
your choice.
4.8.3. Wireless DMX menu
01) If you have chosen WIRELESS HIDE, press the OK button to proceed to the submenu.
02) Press the UP/DOWN buttons to choose between DISABLE and ENABLE.
03) If you have chosen ENABLE, you will be able to adjust the wireless DMX settings in the options menu.
04) If you have chosen DISABLE, you will not be able to adjust the wireless DMX settings.
05) Press the OK button to confirm your choice
4.9. Wireless DMX settings
01) If you have chosen WIRELESS, press the UP/DOWN buttons to choose one of the 2 options:
WDMX ACTIVE
WDMX RESET
02) Press the OK button to confirm your choice.
4.9.1. WDMX active
01) If you have chosen WDMX ACTIVE, press the UP/DOWN buttons to choose between OFF and ON.
02) Press the OK button to confirm your choice.
03) If you have chosen ON, the wireless DMX mode will be active.
4.9.2. WDMX reset
01) If you have chosen WDMX RESET, press the UP/DOWN buttons to choose between OFF and ON.
02) Press the OK button to confirm your choice.
03) If you have chosen ON, the wireless DMX mode will be reset.
18
Page 20
Ordercode: 41391
Expression 8000 Spot
5. Manual mode
With this menu, you can set the manual settings.
01) In the main menu, press the UP/DOWN buttons to choose MANUAL and press the OK button to enter
the menu. The display will show:
02) Press the UP/DOWN buttons to choose one of the 5 options:
CHANNEL
EDIT
RESET
UPLOAD
PERFORM TEST
03) Press the OK button to confirm your choice.
5.1. Channel
01) If you have chosen CHANNEL, press the OK button to enter the submenu.
02) Press the RIGHT button to toggle between the following options:
DIMMER (0-255, from OFF to full ON)
PAN (0-255, from 0-540°)
TILT (0-255, from 0-270°)
PT SPEED (Pan/Tilt speed. 0-255, from fast to slow)
COLOR1 (Color wheel 1)
COLOR2 (Color wheel 2)
FIX GOBO (Static gobo wheel)
ROTA GOBO (Rotating gobos)
GOBO-ROTA (Gobo rotation settings)
ZOOM (0-255, from big to small)
FOCUS (0-255, from big to small)
PRISM (0-255, prism choice)
IRIS (Iris settings)
FROST (Frost settings)
STROBE (0-255, from OFF to high frequency)
03) Press the UP/DOWN buttons to increase/decrease the values. The adjustment range of each option is
between 0-255.
19
Page 21
Ordercode: 41391
Expression 8000 Spot
5.2. Edit
01) If you have chosen EDIT, press the OK button to enter the submenu.
02) Press the UP/DOWN buttons to choose which step you want to edit. There are 50 steps to choose
from.
03) Press the OK button to proceed to edition mode.
04) Press the RIGHT button to toggle between the following options:
DIMMER (0-255, from OFF to full ON)
PAN (0-255, from 0-540°)
TILT (0-255, from 0-270°)
PT SPEED (Pan/Tilt speed. 0-255, from fast to slow)
COLOR1 (Color wheel 1)
COLOR2 (Color wheel 2)
FIX GOBO (Static gobo wheel)
ROTA GOBO (Rotating gobos)
GOBO-ROTA (Gobo rotation settings)
ZOOM (0-255, from big to small)
FOCUS (0-255, from big to small)
PRISM (0-255, prism choice)
IRIS (Iris settings)
FROST (Frost settings)
STROBE (0-255, from OFF to high frequency)
TIME
USE (Yes or No)
05) Press the UP/DOWN buttons to increase/decrease the values. The adjustment range of each option is
between 0-255.
06) Press the OK button to proceed to the following step and repeat the steps1-4.
5.3. Reset
01) If you have chosen RESET, press the OK button to enter the submenu.
02) Press the UP/DOWN buttons to choose one of the 3 options:
RESET PAN/TILT (reset pan/tilt movement)
RESET FRONT (reset LED)
RESET ALL (complete reset)
03) Once you have chosen your preferred option, press the OK button to proceed.
04) Press the UP/DOWN buttons to choose between NO and YES and press the OK button to confirm your
choice.
5.4. Upload
01) If you have chosen UPLOAD, press the OK button to enter the submenu.
02) Press the UP/DOWN buttons to choose one of the 2 options:
UPLOAD PARA (upload the settings from Channel menu)
UPLOAD EDIT (upload the settings from Edit menu)
03) Press the OK button to confirm your choice.
04) Press the UP/DOWN buttons to choose between NO and YES and press the OK button to confirm.
05) If you have chosen YES, the device will perform the desired action.
20
Page 22
Ordercode: 41391
Expression 8000 Spot
5.5. Performance test
01) If you have chosen PERFORM TEST, press the OK button to enter the submenu.
02) The device will ask you about what test you want to perform. Press the OK button to proceed.
03) Press the UP/DOWN buttons to choose the option which you want to test. You can choose from:
PAN/TILT
COLOR
BEAM
GOBO
EFFECT
ALL
04) Press the OK button to perform the test.
6. System information
With this menu you can monitor the current status of the device.
01) In the main menu, press the UP/DOWN buttons to choose INFO and press the OK button to enter the
menu. The display will show:
02) Press the UP/DOWN buttons to toggle between the following menus:
SYSTEM ERROR (current system errors)
FIXTURE HOUR (device’s total lifetime)
LAMP HOUR (time since last power up)
TEMPTURE (device’s current temperature)
VERSION (current software version)
03) Press the OK button to enter the desired menu.
21
Page 23
Ordercode: 41391
Expression 8000 Spot
Channel 5 – PAN/TILT Speed
0-255
From fast to slow
Channel 6 – Color Wheel 1 CH19 must be open
0-10
White
11-19
White/Cyan
20
Cyan
21-29
Cyan/Magenta
30
Magenta
31-39
Magenta/Pink
40
Pink
41-49
Pink/Blue
50
Blue
51-59
Blue/Yellow
60
Yellow
61-69
Yellow/Green
70
Green
71-79
Green/Red
80
Red
81-89
Red/White
90-95
White
96-103
Cyan
104-111
Magenta
112-119
Pink
120-127
Blue
128-135
Yellow
136-143
Green
144-151
Red
152-203
Clockwise color flow, from fast to slow
204-208
Stop
209-255
Counterclockwise color flow, from slow to fast
DMX Channels
23 channels (PERSON1)
Channel 1 – Horizontal movement (Pan)
Move the slider up, in order to move head horizontally (PAN).
Gradual head adjustment from one end of the slider to the other (0-255, 128-center).
The head can be turned by 540° and stopped at any position you wish.
Channel 2 – Pan fine 16 bit
Channel 3 – Vertical movement (Tilt)
Move the slider, up in order to move head vertically (TILT).
Gradual head adjustment from one end of the slider to the other (0-255, 128-center).
The head can be turned by 270° and stopped at any position you wish.
Channel 4 – Tilt fine 16 bit
22
Page 24
Ordercode: 41391
Expression 8000 Spot
Channel 7 – Color Wheel 2 CH19 must be open
0-10
White
11-19
White/CTO
20
CTO
21-29
CTO/CTB
30
CTB
31-39
CTB/UV
40
UV
41-49
UV/Amber
50
Amber
51-59
Amber/Dark Green
60
Dark Green
61-69
Dark Green/Orange
70
Orange
71-79
Orange/Kelly Green
80
Kelly Green
81-89
Kelly Green/White
90-95
White
96-103
CTO
104-111
CTB
112-119
UV 120-127
Amber
128-135
Dark Green
136-143
Orange
144-151
Kelly Green
152-203
Clockwise color flow, from fast to slow
204-208
Stop
209-255
Counterclockwise color flow, from slow to fast
Channel 8 – Static Gobo wheel CH19 must be open
0-10
Open
11-20
Gobo 1
21-30
Gobo 2
31-40
Gobo 3
41-50
Gobo 4
51-60
Gobo 5
61-70
Gobo 6
71-80
Gobo 7
81-90
Gobo 8
91-100
Gobo 9
101-110
Gobo 10
111-120
Gobo 11
121-122
Open
123-132
Static Gobo 1 shake effect, from slow to fast
133-142
Static Gobo 2 shake effect, from slow to fast
143-152
Static Gobo 3 shake effect, from slow to fast
153-162
Static Gobo 4 shake effect, from slow to fast
163-172
Static Gobo 5 shake effect, from slow to fast
173-182
Static Gobo 6 shake effect, from slow to fast
183-192
Static Gobo 7 shake effect, from slow to fast
193-202
Static Gobo 8 shake effect, from slow to fast
203-212
Static Gobo 9 shake effect, from slow to fast
213-222
Static Gobo 10 shake effect, from slow to fast
223-231
Static Gobo 11 shake effect, from slow to fast
232-233
Open
234-255
Gobo flow, from slow to fast
23
Page 25
Ordercode: 41391
Expression 8000 Spot
Channel 9 – Rotating Gobo wheel CH19 must be open
0-10
Open
11-20
Gobo 1
21-30
Gobo 2
31-40
Gobo 3
41-50
Gobo 4
51-60
Gobo 5
61-70
Gobo 6
71-80
Gobo 7
81-82
Open
83-92
Rotating Gobo 1 shake effect, from slow to fast
93-102
Rotating Gobo 2 shake effect, from slow to fast
103-112
Rotating Gobo 3 shake effect, from slow to fast
113-122
Rotating Gobo 4 shake effect, from slow to fast
123-132
Rotating Gobo 5 shake effect, from slow to fast
133-142
Rotating Gobo 6 shake effect, from slow to fast
143-152
Rotating Gobo 7 shake effect, from slow to fast
153-162
Open
163-255
Rotating gobo flow, from slow to fast
Channel 10 – Gobo rotation CH19 and CH9 must be open
0-120
Manual rotation adjustment
121-125
Stop
126-165
Rotating gobo shake effect speed, from slow to fast
166-170
Stop
171-210
Clockwise gobo rotation, from fast to slow
211-215
Stop
216-255
Counterclockwise gobo rotation, from slow to fast
Channel 11 – Prism CH19 must be open
0-10
Open
11-26
Prism ON
27-145
Gradual prism rotation adjustment
146-195
Clockwise prism rotation, from fast to slow
196-205
Prism ON
206-255
Counterclockwise prism rotation, from slow to fast
Channel 12 – Frost effect CH19 must be open
0
Frost OFF
1-179
Gradual frost adjustment, from OFF to full
180-189
Full frost
190-211
Fade in/fast out effect, from slow to fast
212-233
Fast in/fade out effect, from slow to fast
234-255
Random frost effect
Channel 13 – Iris CH19 must be open
0-199
Iris open, from large to small
200-215
Iris closed
216-225
Iris fast open/slow close, speed from slow to fast
226-235
Iris slow open/fast close, speed from slow to fast
236-245
Iris slow close/fast open, random speed
246-255
Iris slow open/fast close, random speed
24
Page 26
Ordercode: 41391
Expression 8000 Spot
Channel 14 – Iris fine CH19 must be open
0-255
Fine iris adjustment
Channel 15 – Zoom CH19 must be open
0-255
Zoom adjustment, from big to small
Channel 16 – Zoom fine CH19 must be open
0-255
Fine zoom adjustment, from big to small
Channel 17 – Focus CH19 must be open
0-200
Gradual focus adjustment
201-255
Auto focus
Channel 18 – Focus fine CH19 must be open
0-255
Fine focus adjustment
Channel 19 – Dimmer
0-255
Dimmer intensity, from dark to brightest
Channel 20 – Dimmer fine CH19 must be open
0-255
Fine dimmer adjustment
Channel 21 – Strobe CH19 must be open
0-9
OFF
10-155
Strobe ON, from slow to fast
156-205
Pulse strobe, from slow to fast
206-255
Strobe, random speed
Channel 22 – Effects CH19 must be open
0-5
Not functional
6-11
Macro 1
12-17
Macro 2
18-23
Macro 3
24-29
Macro 4
30-35
Macro 5
36-41
Macro 6
42-47
Macro 7
48-53
Macro 8
54-59
Macro 9
60-65
Macro 10
66-71
Macro 11
72-77
Macro 12
78-83
Macro 13
84-89
Macro 14
90-95
Macro 15
96-101
Macro 16
102-107
Macro 17
108-113
Macro 18
114-119
Macro 19
120-125
Macro 20
126-131
Macro 21
132-137
Macro 22
138-143
Macro 23
144-149
Macro 24
150-155
Macro 25
25
Page 27
Ordercode: 41391
Expression 8000 Spot
156-161
Macro 26
162-167
Macro 27
168-173
Macro 28
174-179
Macro 29
180-185
Macro 30
186-191
Macro 31
192-197
Macro 32
198-203
Macro 33
204-209
Macro 34
210-215
Macro 35
216-221
Macro 36
222-227
Macro 37
228-233
Macro 38
234-239
Macro 39
240-245
Macro 40
246-255
Not functional
Channel 23 – Functions CH19 must be open
0-10
Not functional
11-25
DIM 0
26-40
DIM 1
41-55
DIM 2
56-70
DIM 3
71-85
DIM 4
86-100
Pan/Tilt speed, fast
101-115
Pan/Tilt speed, normal
116-130
Pan/Tilt blackout (open)
131-145
Pan/Tilt blackout (close)
146-160
Not functional
161-175
Color wheel/gobo wheel/iris reset
176-190
Focus/zoom/frost/strobe/prism reset
191-205
Pan/Tilt reset
206-220
Pan/Tilt reset
221-255
Not functional
Channel 3 – PAN/TILT Speed
0-255
From fast to slow
17 channels (PERSON2)
Channel 1 – Horizontal movement (Pan)
Move the slider up, in order to move head horizontally (PAN).
Gradual head adjustment from one end of the slider to the other (0-255, 128-center).
The head can be turned by 540° and stopped at any position you wish.
Channel 2 – Vertical movement (Tilt)
Move the slider, up in order to move head vertically (TILT).
Gradual head adjustment from one end of the slider to the other (0-255, 128-center).
The head can be turned by 270° and stopped at any position you wish.
26
Page 28
Ordercode: 41391
Expression 8000 Spot
Channel 4 – Color Wheel 1 CH14 must be open
0-10
White
11-19
White/Cyan
20
Cyan
21-29
Cyan/Magenta
30
Magenta
31-39
Magenta/Pink
40
Pink
41-49
Pink/Blue
50
Blue
51-59
Blue/Yellow
60
Yellow
61-69
Yellow/Green
70
Green
71-79
Green/Red
80
Red
81-89
Red/White
90-95
White
96-103
Cyan
104-111
Magenta
112-119
Pink
120-127
Blue
128-135
Yellow
136-143
Green
144-151
Red
152-203
Clockwise color flow, from fast to slow
204-208
Stop
209-255
Counterclockwise color flow, from slow to fast
Channel 5 – Color Wheel 2 CH14 must be open
0-10
White
11-19
White/CTO
20
CTO
21-29
CTO/CTB
30
CTB
31-39
CTB/UV
40
UV
41-49
UV/Amber
50
Amber
51-59
Amber/Dark Green
60
Dark Green
61-69
Dark Green/Orange
70
Orange
71-79
Orange/Kelly Green
80
Kelly Green
81-89
Kelly Green/White
90-95
White
96-103
CTO
104-111
CTB 112-119
UV 120-127
Amber
128-135
Dark Green
136-143
Orange
144-151
Kelly Green
152-203
Clockwise color flow, from fast to slow
204-208
Stop
209-255
Counterclockwise color flow, from slow to fast
27
Page 29
Ordercode: 41391
Expression 8000 Spot
Channel 6 – Static Gobo wheel CH14 must be open
0-10
Open
11-20
Gobo 1
21-30
Gobo 2
31-40
Gobo 3
41-50
Gobo 4
51-60
Gobo 5
61-70
Gobo 6
71-80
Gobo 7
81-90
Gobo 8
91-100
Gobo 9
101-110
Gobo 10
111-120
Gobo 11
121-122
Open
123-132
Static Gobo 1 shake effect, from slow to fast
133-142
Static Gobo 2 shake effect, from slow to fast
143-152
Static Gobo 3 shake effect, from slow to fast
153-162
Static Gobo 4 shake effect, from slow to fast
163-172
Static Gobo 5 shake effect, from slow to fast
173-182
Static Gobo 6 shake effect, from slow to fast
183-192
Static Gobo 7 shake effect, from slow to fast
193-202
Static Gobo 8 shake effect, from slow to fast
203-212
Static Gobo 9 shake effect, from slow to fast
213-222
Static Gobo 10 shake effect, from slow to fast
223-231
Static Gobo 11 shake effect, from slow to fast
232-233
Open
234-255
Gobo flow, from slow to fast
Channel 7 – Rotating Gobo wheel CH14 must be open
0-10
Open
11-20
Gobo 1
21-30
Gobo 2
31-40
Gobo 3
41-50
Gobo 4
51-60
Gobo 5
61-70
Gobo 6
71-80
Gobo 7
81-82
Open
83-92
Rotating Gobo 1 shake effect, from slow to fast
93-102
Rotating Gobo 2 shake effect, from slow to fast
103-112
Rotating Gobo 3 shake effect, from slow to fast
113-122
Rotating Gobo 4 shake effect, from slow to fast
123-132
Rotating Gobo 5 shake effect, from slow to fast
133-142
Rotating Gobo 6 shake effect, from slow to fast
143-152
Rotating Gobo 7 shake effect, from slow to fast
153-162
Open
163-255
Rotating gobo flow, from slow to fast
28
Page 30
Ordercode: 41391
Expression 8000 Spot
Channel 8 – Gobo rotation CH14 and CH7 must be open
0-120
Manual rotation adjustment
121-125
Stop
126-165
Rotating gobo shake effect speed, from slow to fast
166-170
Stop
171-210
Clockwise gobo rotation, from fast to slow
211-215
Stop
216-255
Counterclockwise gobo rotation, from slow to fast
Channel 9 – Prism CH14 must be open
0-10
Open
11-26
Prism ON
27-145
Gradual prism rotation adjustment
146-195
Clockwise prism rotation, from fast to slow
196-205
Prism ON
206-255
Counterclockwise prism rotation, from slow to fast
Channel 10 – Frost effect CH14 must be open
0
Frost OFF
1-179
Gradual frost adjustment, from OFF to full
180-189
Full frost
190-211
Fade in/fast out effect, from slow to fast
212-233
Fast in/fade out effect, from slow to fast
234-255
Random frost effect
Channel 11 – Iris CH14 must be open
0-199
Iris open, from large to small
200-215
Iris closed
216-225
Iris fast open/slow close, speed from slow to fast
226-235
Iris slow open/fast close, speed from slow to fast
236-245
Iris slow close/fast open, random speed
246-255
Iris slow open/fast close, random speed
Channel 12 – Zoom CH14 must be open
0-255
Zoom adjustment, from big to small
Channel 13 – Focus CH14 must be open
0-200
Gradual focus adjustment
201-255
Auto focus
Channel 14 – Dimmer
0-255
Dimmer intensity, from dark to brightest
Channel 15 – Strobe CH14 must be open
0-9
OFF
10-155
Strobe ON, from slow to fast
156-205
Pulse strobe, from slow to fast
206-255
Strobe, random speed
29
Page 31
Ordercode: 41391
Expression 8000 Spot
Channel 16 – Effects CH14 must be open
0-5
Not functional
6-11
Macro 1
12-17
Macro 2
18-23
Macro 3
24-29
Macro 4
30-35
Macro 5
36-41
Macro 6
42-47
Macro 7
48-53
Macro 8
54-59
Macro 9
60-65
Macro 10
66-71
Macro 11
72-77
Macro 12
78-83
Macro 13
84-89
Macro 14
90-95
Macro 15
96-101
Macro 16
102-107
Macro 17
108-113
Macro 18
114-119
Macro 19
120-125
Macro 20
126-131
Macro 21
132-137
Macro 22
138-143
Macro 23
144-149
Macro 24
150-155
Macro 25
156-161
Macro 26
162-167
Macro 27
168-173
Macro 28
174-179
Macro 29
180-185
Macro 30
186-191
Macro 31
192-197
Macro 32
198-203
Macro 33
204-209
Macro 34
210-215
Macro 35
216-221
Macro 36
222-227
Macro 37
228-233
Macro 38
234-239
Macro 39
240-245
Macro 40
246-255
Not functional
Channel 17 – Functions CH14 must be open
0-10
Not functional
11-25
DIM 0
26-40
DIM 1
41-55
DIM 2
56-70
DIM 3
71-85
DIM 4
86-100
Pan/Tilt speed, fast
101-115
Pan/Tilt speed, normal
116-130
Pan/Tilt blackout (open)
131-145
Pan/Tilt blackout (close)
146-160
Not functional
30
Page 32
Ordercode: 41391
Expression 8000 Spot
161-175
Color wheel/gobo wheel/iris reset
176-190
Focus/zoom/frost/strobe/prism reset
191-205
Pan/Tilt reset
206-220
Pan/Tilt reset
221-255
Not functional
Maintenance
The operator has to make sure that safety-relating and machine-technical installations are to be
inspected by an expert after every year in the course of an acceptance test.
The operator has to make sure that safety-related and machine-technical installations are to be
inspected by a skilled person once a year.
The following points have to be considered during the inspection:
01) All screws used for installing the device or parts of the device have to be tightly connected and
must not be corroded.
02) There may not be any deformations on housings, fixations and installation spots.
03) Mechanically moving parts like axles, eyes and others may not show any traces of wearing.
04) The electric power supply cables must not show any damages or material fatigue.
The Expression 8000 Spot requires almost no maintenance. However, you should keep the unit clean.
Otherwise, the fixture’s light-output will be significantly reduced. Disconnect the mains power supply, and
then wipe the cover with a damp cloth. Do not immerse in liquid. Wipe lens clean with glass cleaner and
a soft cloth. Do not use alcohol or solvents.
The front lens will require weekly cleaning, as smoke-fluid tends to build up residues, reducing the lightoutput very quickly.
The cooling fans, color wheel, the gobo wheel, the gobos and the internal lenses should be cleaned
monthly, with a soft brush.
Please clean internal components once a year with a light brush and vacuum cleaner.
Keep connections clean. Disconnect electric power, and then wipe the DMX and audio connections
with a damp cloth. Make sure connections are thoroughly dry before linking equipment or supplying
electric power.
Replacing the Fuse
Power surges, short-circuit or inappropriate electrical power supply may cause a fuse to burn out. If the
fuse burns out, the product will not function whatsoever. If this happens, follow the directions below:
01) Unplug the unit from electric power source.
02) Insert a flat-head screwdriver into a slot in the fuse cover. Turn the screwdriver to the left, at the same
time gently push a bit (Turn and Push). The fuse will come out.
03) Remove the used fuse. If brown or unclear, it is burned out.
04) Insert the replacement fuse into the holder where the old fuse was. Reinsert the fuse cover. Be sure to
use a fuse of the same type and specification. See the product specification label for details.
31
Page 33
Ordercode: 41391
Expression 8000 Spot
01) Disconnect mains power supply and set the switch to OFF.
02) Make sure that the gobo which you want to insert has the same size. For the right size, see below.
Fig. 06
Fig. 07
Gobo Size
Replacing a gobo from the rotating gobo wheel
03) Before removing the top part of the housing, make sure that the moving head is in the horizontal
position. The lens position should be on the bottom, symmetrically speaking.
04) Loosen all the four screws on the back of the housing.
05) Gently tilt the head so that the small metal housing slides out easily.
06) Turn the gobo wheel until you reach the gobo which you want to remove.
32
Page 34
Ordercode: 41391
Expression 8000 Spot
Fig. 08
08) Very carefully take the gobo out of the gobo holder with a pair of pliers.
09) Place the new gobo in the gobo holder. Carefully put the pinchcock back, gently press the
pinchcock a little bit together. To do it, you can use a pair of pliers.
10) Put the gobo holder back. At first, you will notice some resistance which is caused by the way in
which the holder was built.
11) Replace the maintenance caps and fasten all the screws.
When an object is held up to the coated
side, there is no space between the object
and its reflection. The back edge of the
gobo cannot be seen when looking
through the coated side.
When an object is held up to the uncoated
side, there is a space between the object and
its reflection. The back edge of the gobo can
be seen when looking through the uncoated
side.
07) Gently lift up the gobo holder 10º and then gently pull out the gobo from its position.
Glass Gobo Orientation
Coated glass gobos are inserted with the coating against the rim of the holder (away from the spring).
Textured gobos are inserted with the smooth side against the spring. This provides the best results when
combining rotating gobos.
33
Page 35
Ordercode: 41391
Expression 8000 Spot
Static Gobo wheel
Rotating Gobo wheel
Color wheel 1
Color wheel 2
Rotating/Static Gobo wheels and Color wheels
Troubleshooting
This troubleshooting guide is meant to help solve simple problems.
If a problem occurs, carry out the steps below in sequence until a solution is found. Once the unit
operates properly, do not carry out following steps.
No Light
If the light effect does not operate properly, refer servicing to a technician.
Suspect three potential problem areas as: the power supply, the LEDs, the fuse.
01) Power supply. Check that the unit is plugged into an appropriate power supply.
02) The LEDs. Return the Expression to your Showtec dealer.
03) The fuse. Replace the fuse. See page 31 for replacing the fuse.
04) If all of the above appears to be O.K., plug the unit in again.
05) If you are unable to determine the cause of the problem, do not open the Expression, as this may
damage the unit and the warranty will become void.
06) Return the device to your Showtec dealer.
34
Page 36
Ordercode: 41391
Expression 8000 Spot
Problem
Probable cause(s)
Solution
One or more
fixtures do not
function at all
No power to the fixture
• Check if power is switched on and
cables are plugged in
Primary fuse blown
• Replace fuse
Fixtures reset
correctly, but all
respond
erratically or not
at all to the
controller
The controller is not connected.
• Connect controller.
3-pin/5-pin XLR Out of the
controller does not match XLR Out
of the first fixture on the link (i.e.
signal is reversed)
• Install a phase reversing cable
between the controller and the
first fixture on the link
Fixtures reset
correctly, but
some respond
erratically or not
at all to the
controller
Poor data quality
• Check data quality. If much lower
than 100 percent, the problem
may be a bad data link
connection, poor quality or
broken cables, missing termination
plug, or a defective fixture
disturbing the link
Bad data link connection
• Inspect connections and cables.
Correct poor connections. Repair
or replace damaged cables
Data link not terminated with 120
Ohm termination plug
• Insert termination plug in output
jack of the last fixture on the link
Incorrect addressing of the fixtures
• Check address setting
One of the fixtures is defective and
disturbs data transmission on the
link
• Bypass one fixture at a time until
normal operation is restored:
unplug both connectors and
connect them directly together.
• Have the defective fixture
serviced by a qualified technician
3-pin/5-pin XLR Out on the fixtures
does not match (pins 2 and 3
reversed)
• Install a phase-reversing cable
between the fixtures or swap pin 2
and 3 in the fixture that behaves
erratically
Shutter closes
suddenly
The color wheel, gobo wheel or a
gobo has lost its index position and
the fixture is resetting the effect
• Contact a technician for servicing
if the problem persists
No light or lamp
cuts out
intermittently
Fixture is too hot
• Allow the fixture to cool down
• Clean the fan
• Make sure air vents in control
panel and the front lens are not
blocked
• Turn up the air conditioning
LEDs damaged
• Disconnect the fixture and return it
to your dealer
The power supply settings do not
match local AC voltage and
frequency
• Disconnect fixture. Check settings
and correct if necessary
No Response to DMX
Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card malfunction.
01) Check the DMX setting. Make sure that DMX addresses are correct.
02) Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power.
Try your DMX control again.
03) Determine whether the controller or light effect is at fault. Does the controller operate properly with
other DMX products? If not, take the controller in for repair. If so, take the DMX cable and the light
effect to a qualified technician.
35
Page 37
Ordercode: 41391
Expression 8000 Spot
Model:
Showtec Expression 8000 Spot
Input Voltage:
100-240 VAC, 60/50Hz
Power consumption:
280W (full output)
DMX linking:
30pcs
Fuse:
T6,3AL/250V
Dimensions:
450 x 390 x 640 mm (LxWxH)
Weight:
26 kg
Operating and Programming:
Signal pin OUT:
Pin 1 (earth), pin 2 (-), pin 3 (+)
DMX Mode:
17, 23 channels
Signal input:
3-pin/5-pin XLR IN
Signal output:
3-pin/5-pin XLR OUT
Electro-mechanical effects:
Light source:
230W LED module
Lumen:
8000 lumen
Peak intensity:
160000cd
Color mixing:
7 dichroic filters + white
Gobos:
7 rotating gobos + 11 static gobos
Focus and iris:
Motorized
Zoom:
13-35°
Pan & Tilt range
540°/270°
Dimmer:
0-100%
Strobe:
0-20Hz
Housing:
Metal & Flame retardant plastic
DMX-control:
via standard DMX-controller
On Board:
LCD display for easy setup
Control:
Auto, Manual, Master/Slave, DMX-512
Connections:
Dedicated Schuko to PowerCON & Data connector
Cooling:
Internal fan
Max. ambient temperature ta:
40°C
Max. housing temperature tB:
80°C
Minimum distance:
Minimum distance from flammable surfaces:
0,5 m
Minimum distance to lighted object:
12 m
Product Specifications
Design and product specifications are subject to change without prior notice.
Website: www.Showtec.info
Email: service@highlite.nl
36
Page 38
Ordercode: 41391
Expression 8000 Spot
Dimensions
37
Page 39
Ordercode: 41391
Expression 8000 Spot
Notes
38
Page 40
©2015 Showtec
Loading...