Colorburst V1
Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
Ordercode: 43163
MANUAL
ENGLISH
1
Ordercode: 43163
Colorburst
Table of contents
Warning ............................................................................................................................................................................... 2
Safety Instructions ......................................................................................................................................................... 2
Operating Determinations .......................................................................................................................................... 5
Laser safety for a Class 3B Laser Product ................................................................................................................. 5
Rigging ............................................................................................................................................................................ 7
Connection with the mains ......................................................................................................................................... 8
Return Procedure .......................................................................................................................................................... 8
Claims .............................................................................................................................................................................. 8
Description of the device ................................................................................................................................................. 9
Optional accessories .................................................................................................................................................... 9
Frontside ........................................................................................................................................................................10
Backside .......................................................................................................................................................................10
Installation .........................................................................................................................................................................11
Set Up and Operation .....................................................................................................................................................11
Control Modes .............................................................................................................................................................12
One Colorburst (Auto Programs and Static Color Mode) ...............................................................................12
One Colorburst (Sound-controlled)......................................................................................................................12
Multiple Colorbursts (Master/Slave control) .......................................................................................................13
Multiple Colorbursts (DMX Control) ......................................................................................................................13
Fixture Linking ...............................................................................................................................................................14
Data Cabling ...............................................................................................................................................................14
Control Panel ...............................................................................................................................................................15
Control Mode ..............................................................................................................................................................15
DMX Addressing ..........................................................................................................................................................15
Menu Overview ...........................................................................................................................................................16
Main Menu Options ....................................................................................................................................................16
1. Auto Run Programs..............................................................................................................................................17
2. Sound-controlled Mode .....................................................................................................................................17
3. Static Control Mode ............................................................................................................................................17
4. DMX Address / DMX Channels ..........................................................................................................................18
5. Slave mode ...........................................................................................................................................................18
6. System Settings .....................................................................................................................................................18
Remote Control ...........................................................................................................................................................19
DMX Channels .............................................................................................................................................................20
3 channels .................................................................................................................................................................20
10 channels ...............................................................................................................................................................20
22 channels ...............................................................................................................................................................22
Maintenance ...............................................................................................................................................................24
Replacing the Fuse .....................................................................................................................................................24
Troubleshooting ...............................................................................................................................................................25
No Light .........................................................................................................................................................................25
No Response to DMX ..................................................................................................................................................25
Product Specifications ....................................................................................................................................................27
Dimensions ........................................................................................................................................................................28
Notes ..................................................................................................................................................................................29
2
Ordercode: 43163
Colorburst
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
● Showtec Colorburst
● IEC Power cable (1,5 m)
● 2 keys for the interlock
● Remote control plug
● IR Remote control
● Mounting bracket with screws
● User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason, when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving the lifespan is of higher priority, place care in providing for lower
operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity.
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
● be qualified
● follow the instructions of this manual
3
Ordercode: 43163
Colorburst
Before the initial start-up, please make sure that there is no damage caused by transportation.
Should there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes contained in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
● Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
● Never modify, bend, mechanically strain, put pressure on, pull or heat up the power cord.
● Never strain the cable insert or the female part in the device. There must always be sufficient cable
going to the device. Otherwise, the cable will be damaged, which can cause serious damage.
● Never remove warning or informative labels from the unit.
● Never use anything to cover the ground contact.
● Never lift the fixture holding it by the projector-head, as the mechanics may be damaged. Always
hold the fixture by the transport handles.
● Never place any material over the LEDs or lens.
● Never look directly into the light source.
● Never leave any cables lying around.
● Never use the device during thunderstorms, unplug the device immediately.
● Never leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within
children’s reach, as they are potential sources of danger.
● Never aim the laser beam at people or animals!
● Never point a laser at aircraft, this is a federal offense.
● Never point unterminated laser beams into the sky.
● Never open the laser housing. The high laser power levels inside of the protective housing can start
fires, burn skin and will cause instant eye injury.
● Do not insert objects into air vents.
● Do not open the device and do not modify the device.
● Do not connect this device to a dimmerpack.
● Do not open the device and do not modify the device.
● Do not point lasers at highly reflective surfaces such as windows, mirrors and shiny metal. Even laser
reflections can be hazardous.
● Do not expose the output optic (aperture) to cleaning chemicals.
● Do not use laser if the laser appears to be emitting only one or two beams.
● Do not use laser if housing is damaged or open, or if optics appear damaged in any way.
● Do not operate laser without first reading and understanding all safety and technical data in this
manual. Never look into the laser aperture or laser beams.
● Do not switch the device on and off in short intervals, as this will reduce the device’s life.
● Do not touch the device’s housing bare-handed during its operation (housing becomes very hot).
Allow the fixture to cool for at least 5 minutes before handling.
● Do not shake the device. Avoid brute force when installing or operating the device.
4
Ordercode: 43163
Colorburst
● After set up and prior to public use, test laser to ensure proper function. Do not use the laser if any
defect is detected. Do not use, if the laser emits only one or two laser beams rather than
dozens/hundreds, as this could indicate damage to the diffraction grating optic, and could allow
emission of higher laser levels.
● Only use the device indoors, avoid contact with water or other liquids.
● Only operate the fixture after having checked if the housing is firmly closed and all screws are tightly
fastened.
● Only operate the device after having familiarized with its functions.
● Avoid flames and do not put close to flammable liquids or gases.
● Always check the regulations when using a class 2M laser product.
● Always check and position the laser before anybody enters the room, when the laser is facing an
area with people.
● Always keep the case closed while operating.
● Always allow a free air space of at least 50 cm around the unit for ventilation.
● Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord holding it by the plug. Never pull out the plug by tugging the power cord.
● Make sure that the device is not exposed to extreme heat, moisture or dust.
● Make sure that the available voltage is not higher than stated on the rear panel.
● Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
● Make sure that the core diameter of extension cords and power cords is sufficient for the required
power consumption of the device.
● If the external cable is damaged, it has to be replaced by a qualified technician.
● If the lens or LEDs are obviously damaged, it has to be replaced. So that its functions are not
impaired, due to cracks or deep scratches.
● If device was dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
● If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
● If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
● For adult use only. The fixture must be installed beyond the reach of children. Never leave the unit
running unattended.
● Never attempt to bypass the thermostatic switch or fuses.
● For replacement use fuses of same type and rating only.
● The operation of a class 2M laser show laser is only allowed if the show is controlled by a skilled and
well-trained operator familiar with the data included in this manual.
● The user is responsible for correct positioning and operating of the Colorburst. The manufacturer will
not accept liability for damages caused by the misuse or incorrect installation of this device.
● This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
● The laser will only work between 10-35ºC.
● After 3 hours working, you must shut off the laser and let the laser diode cool off for 30 minutes,
otherwise the laser could be damaged and the warranty becomes void.
● Repairs, servicing and electric connection must be carried out by a qualified technician.
● WARRANTY: Till one year after date of purchase.
5
Ordercode: 43163
Colorburst
Operating Determinations
● This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
● The minimum distance between light output and the illuminated surface must be bigger than 1
meter.
● The maximum ambient temperature t
a
= 40°C must never be exceeded.
● The relative humidity must not exceed 50 % with an ambient temperature of 40° C.
● If this device is operated in any other way than the one described in this manual, the product may
suffer damages and the warranty becomes void.
● Any other operation may lead to dangers like short-circuit, burns, electric shock, crash, etc.
You endanger your own safety and the safety of others!
Laser safety for a Class 2M Laser Product
Laser Light is different from any other light source with which you may be familiar with. This laser is less
dangerous than a higher class laser such as an 3B or 4. The light from this product is safe for unintentional
(<1/4 sec) unaided eye exposure. However this device is potentially hazardous if viewed with certain
optical instruments such as binoculars or eye loupe.
Laser light is thousands of times more concentrated than light from any other kind of light source. This
concentration of light power can cause instant eye injuries, primarily by burning the retina (the light
sensitive portion at the back of the eye). Even if you cannot feel “heat” from a laser beam, it can still
potentially injure or blind you or your audience.
Even very small amounts of laser light are potentially hazardous even at long distances. Laser eye injuries
can happen quicker than you can blink.
It is incorrect to think that because these laser products split the laser into hundreds of beams or the laser
beam is scanned out in high speed, that an individual laser beam is safe for eye exposure. This laser
product uses dozens of milliwatts of laser power (Class 2M levels internally). Many of the individual beams
are potentially hazardous to the eyes.
It is also incorrect to assume that because the laser light is moving, it is safe. This is not true. Nor, do the
laser beams always move. Since eye injuries can occur instantly, it is critical to prevent the possibility of
any direct eye exposure. According to the laser safety regulation, it is not legal to aim Class 2M lasers in
areas which people can get exposed. This is true even if it is aimed below people’s faces, such as on a
dance floor.
CAUTION! Only Laser Safety Officers who are officially certified by a regulatory body or authorized
training organization are allowed to use class 2M lasers in public. The Laser Safety Officer is responsible for
all aspects when using this laser, including following all locally applicable safety laws and regulations.
The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of
this laser.
CAUTION: AVOID EXPOSURE TO BEAM: Avoid direct eye contact with laser
light. Never intentionally expose your eyes or others to direct laser
radiation.
6
Ordercode: 43163
Colorburst
Compliance Statement
Your Colorburst Laser has been designed to comply with FDA and IEC Standards for its classification.
The Colorburst is a Class 2M laser product.
Laser Safety and Compliance Information
The Colorburst is manufactured to comply with the IEC 60825-1 and in accordance with U.S. Food and
Drug Administration (FDA) Standards Listed under FDA Document 21 CFR 1040 and subsequent laser
notices.
Product Classification and Manufacturing Label Identification
Laser Classification
Class 2M
Cooling
Cooling fans and TE Cooling
Laser medium
wavelength 650 nm / Red (Laser Diode GaAIAs) ; Output >100mW
wavelength 532 nm / Green (DPSS Nd: YVO4); Output >35mW
Output
135mW
Beam Diameter
<5mm at aperture
Pulse Data All pulses
< 4Hz (>0.25sec)
Divergence (each beam)
<2 mrad
Divergence (total light)
<160 degrees
The legal requirements for using laser entertainment products vary from country to country. The user is
responsible for the legal requirements at the location/country of use.
Further guidelines and safety programs for safe use of lasers can be found in the ANSI Z136.1 Standard
“For Safe Use of Lasers”, available from www.lia.org/. Many local governments, corporations, agencies,
military and others, require all lasers to be used under the guidelines of ANSI Z136.1. Laser Display
guidance can be obtained via the International Laser Display Association, www.ilda.com/index.htm.
CAUTION: The use of corrective eye wear or optics for viewing at distances such as telescopes or
binoculars within a distance of 100mm may pose an eye hazard.
This laser product is a Class 2M laser and has an interlocked
housing.
There are no user serviceable parts inside. Tampering or
removing warranty seals will void your products limited
warranty.
Combo label with the Product Model Number, Serial
Number, Date of Manufacturing, Laser Light Warning Label,
Warranty Void Label and Interlocked Housing Label
Proper Usage Safety and Compliance Information
7
Ordercode: 43163
Colorburst
According to FDA Regulations you should
operate this product as stated on the left.
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself !
Always let the installation be carried out by an authorized dealer !
Procedure:
● If the Colorburst is lowered from the ceiling or high joists, professional trussing systems have to be
used.
● Use a clamp to mount the Colorburst, with the mounting bracket, to the trussing system.
● The Colorburst must never be fixed swinging freely in the room.
● The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety cable.
● When rigging, derigging or servicing the Colorburst, always make sure, that the area below the
installation site is secured and that there are not any unauthorized people around.
The Colorburst can be placed on a flat stage floor or mounted to any kind of truss with a clamp.
Improper installation can cause serious injuries and/or damage of property!
8
Ordercode: 43163
Colorburst
Connection with the mains
Connect the device to the mains with the power-plug.
Always check if the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE
GROUND
Make sure that the device is always properly connected to the earth!
Improper installation can cause serious injuries and/or damage of property!
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail aftersales@highlite.nl and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause of the
return. Be sure to properly pack fixture as any shipping damage resulting from inadequate packaging is
the customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name.
02) Your address.
03) Your phone number.
04) A brief description of the symptoms.
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any shortcomings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that the fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
agreed otherwise in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the
invoice. After this period, complaints will not be handled anymore.
Complaints will only be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of which the obligation is resulting.
9
Ordercode: 43163
Colorburst
Description of the device
Features
The Colorburst is a multifunctional light effect with high output and great effects. It combines laser
effects, strobe effects and LED effects in one device.
● Multifunctional device
● RGBW LEDs
● Input voltage: 100-240V AC, 50/60Hz
● Power consumption: 63W (full output)
● DMX channels: 3, 10 or 22 channels
● 4-digit LED display for easy setup
● Control modes: Auto, Sound-controlled, Static color, Master/Slave, DMX
● Control protocol: DMX-512
● Protection rate: IP-20
● Housing: Die-cast black aluminum
● Cooling: Fans/Convection
● Connections: IEC connectors (IN/OUT), 3-pin XLR (IN/OUT)
● Fuse: T1.6L/250V
● Dimensions: 320 x 320 x 400 mm (LxWxH)
● Weight: 3,8 kg
LED Spot effect
● Light source: 5 x 8W RGBW LEDs
Laser effect
● Laser Color: Red, Green
● Laser Power: 135mW (100mW 650nm Red, 35mW 532nm Green)
● Laser Class: 2M
● Safety Features: Key switch, Interlock, Safety eye
● Laser Safety: EN/IEC 60825-1 Ed 2, 2007-03
Note: Knowledge of DMX is required to fully utilize this unit.
Optional accessories
51316 Remote Interlock
10
Ordercode: 43163
Colorburst
Frontside
Fig. 01
01) Laser lens
02) 5 x 8W RGBW LEDs
03) IR-remote sensor
04) LED display + menu buttons + Function LED indicators
05) Sound sensitivity control
06) Built-in microphone
07) Remote control plug
08) Safety eye
09) Interlock
Backside
Fig. 02
10) IEC Power connector OUT
11) IEC Power connector IN + Fuse T1.6L/250V
12) Ground/earth connection
13) 3-pin DMX signal connector OUT
14) IR-remote sensor
15) 3-pin DMX signal connector IN
11
Ordercode: 43163
Colorburst
Installation
Remove all packing materials from the Colorburst. Check if all foam and plastic padding is removed.
Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Connect the device to the main power supply. The device can be sound-controlled as it is equipped
with a built-in microphone.
The Interlock plug/remote plug and safety keys are included in the box.
The interlock is the “included-in-the-box” successor for the optional remote interlock (51316).
They should be kept with the Colorburst !!!
The following safety precautions should be followed:
● The remote control plug should be placed on the frontside (06)
of your Colorburst.
● The keys should be put into the lock (08) of your Colorburst.
Warning
If the plug is not connected, your laser will not function.
If the key is not set to ON, your laser will not function.
Fig. 03
12
Ordercode: 43163
Colorburst
Exclusion of liability
Be aware that in some countries, there are additional regulations, regarding the use of laser devices.
Therefore, we strongly advise you to verify your national laws with your authorities: We do not take any
responsibility for eventual discrepancies, changes or adaptions regarding lawful use of laser devices.
Fig. 04
Control Modes
There are 5 modes:
• Auto Programs
• Static Color (manual)
• Sound-controlled
• Master/slave
• DMX-512 (3CH, 10CH or 22CH)
One Colorburst (Auto Programs and Static Color Mode)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Colorburst is not connected with a DMX cable, it functions as a stand-alone device.
Please see pages 17 and 18 for more information about Auto Program and Static Color Mode.
One Colorburst (Sound-controlled)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Turn on the music. If the device is set to sound-control, then the Colorburst will react to the beat of
the music. Please see page 17 for more information about the sound-control options.
13
Ordercode: 43163
Colorburst
Multiple Colorbursts (Master/Slave control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Use a 3-p XLR cable to connect the Colorbursts and other devices.
The pins:
1. Earth
2. Signal (-)
3. Signal (+)
04) Link the units as shown in Fig. 05, connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second and third units. You can use the
same functions on the master device as described on pages 17 and 18 (Auto, Static color). This
means you can set your desired operation mode on the master device and all slave devices will
react the same as the master device.
Multiple Colorbursts (Master/Slave control)
Fig. 05
Multiple Colorbursts (DMX Control)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Use a 3-pin XLR cable to connect the Colorbursts and other devices.
04) Link the units as shown in Fig. 06. Connect the first unit's DMX "out" socket with the second unit's "in"
socket, using a DMX-signal cable. Repeat this process to link the second and third units.
05) Supply electric power: Plug electric mains power cords into each unit's IEC socket, then plug the
other end of the mains power cord into proper electric power supply sockets, starting with the first
unit. Do not supply power before the whole system is set up and connected properly.
14
Ordercode: 43163
Colorburst
Multiple Colorbursts DMX Set Up
Fig. 06
Note: Link all cables before connecting electric power
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
Important:
Fixtures on a serial data link must be daisy-chained in a single line. To comply with the
EIA-485 standard, no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX
optically isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of fixtures on a DMX data link: 30 fixtures
Maximum recommended number of fixtures on a power link @ 110V: 12 fixtures
Maximum recommended number of fixtures on a power link @ 240V: 21 fixtures
Data Cabling
To link fixtures together, you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your own cable,
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio DMX Data Cables
● DAP Audio Basic microphone cable for allround use. bal. XLR/M 3-pin > XLR/F 3-pin. Ordercode
FL01150 (1,5 m), FL013 (3 m), FL016 (6 m), FL0110 (10 m), FL0115 (15 m), FL0120 (20 m).
● DAP Audio X-type data cable XLR/M 3-pin > XLR/F 3-pin. Ordercode FLX0175 (0,75 m),
● FLX01150 (1,5 m), FLX013 (3 m), FLX016 (6 m), FLX0110 (10 m).
● DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5 m), FL713 (3 m), FL716 (6 m), FL7110 (10 m).
● DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m), FL7210 (10 m).
● DAP Audio 110 Ohm cable with digital signal transmission. Ordercode FL0975 (0,75 m),
● FL09150 (1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m).
● DAP Audio data cable FL08 DMX/AES-EBU, XLR/M 5-pin > XLR/F 5-pin. Ordercode FL08150 (1,5 m),
FL083 (3 m), FL086 (6 m), FL0810 (10 m), FL0820 (20 m).
● DAP Audio DMX adapter: 5-pin/3-pin. Ordercode FLA29.
● DAP Audio DMX adapter: 3-pin/5-pin. Ordercode FLA30.
15
Ordercode: 43163
Colorburst
The Colorburst can be operated with a controller in control mode or without the controller in stand-alone
mode.
Control Panel
A) DMX LED
B) LED display
C) Auto LED
D) Sound LED
E) Menu button
F) Up button
G) Down button
H) Enter button
I) Slave LED
Fig. 07
Control Mode
The fixtures are individually addressed on a data-link and connected to the controller.
The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it,
the controller will display the saved DMX address, next time.)
DMX Addressing
The control panel on the back side of the device allows you to assign DMX fixture addresses, which is the
first channel with which the Colorburst will respond to the controller.
Please note, when you use the controller, the unit has 22 channels.
When using multiple Colorbursts, make sure you set the DMX addresses right.
Therefore, the DMX address of the first Colorburst should be 1(d001); the DMX address of the second
Colorburst should be 1+22=23 (d023); the DMX address of the third Colorburst should be 23+22=45 (d045),
etc. Please, be sure that you do not have any overlapping channels in order to control each Colorburst
correctly. If two or more Colorbursts are addressed similarly, they will work similarly.
Controlling:
After having addressed all Colorburst fixtures, you may now start operating these via your lighting
controller.
Note: After switching on, the Colorburst will automatically detect whether DMX 512 data is received or
not. If there is no data received , the problem may be:
• The XLR cable from the controller is not connected with the input of the Colorburst.
• The controller is switched off or defective, the cable or connector is detective, or the signal wires are
swapped in the input connector.
Note: It is necessary to insert an XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.
Display Off after 40 seconds
When no button is pressed for 40 seconds, the display will turn off in case this is set in the menu System
Settings, see page 18 for more information.
To light up the display, you have to press the Menu, Enter, Up or Down button.
Once you have pressed the button, the display will light up.
16
Ordercode: 43163
Colorburst
Menu Overview
The Colorburst will only show its version number at start-up !
Main Menu Options
Auto Run Programs
Sound-controlled Mode
Static Color Mode
DMX Channels / DMX Address
Slave Mode
System Settings
17
Ordercode: 43163
Colorburst
1. Auto Run Programs
With this menu you can start several Auto Run Programs.
01) Press the Menu button until the display shows .
02) Press the Enter button to open the menu.
03) Press the Up and Down buttons to choose between 7 built-in programs .
04) Choose the desired built-in program and press the Enter button to confirm.
05) The Colorburst will immediately start the desired Auto run program.
06) Press the Enter button again to set the speed of the desired Auto run program.
07) Press the Up and Down buttons to adjust the speed between , from slow to fast.
2. Sound-controlled Mode
With this menu you can choose several Sound-controlled programs.
01) Press the Menu button until the display shows .
02) Press the Enter button to open the menu.
03) Press the Up and Down buttons to choose between 7 Sound-controlled programs
.
04) Choose the desired type and press the Enter button to confirm.
05) Turn on the music and the Colorburst will immediately start the desired Sound-controlled program.
3. Static Control Mode
With this menu you can manually set the LEDs, control the rotation and activate the laser.
01) Press the Menu button until the display shows .
02) Press the Enter button to open the menu, the display will show .
03) Press the Enter button again to open the submenu:
Red intensity
Green intensity
Blue intensity
White intensity
Strobe static colors
Laser settings
Strobe Laser
Rotation direction
Rotation speed
04) Scroll with the Enter button between the options.
05) If you choose the Red, Green, Blue or White intensity, press the Up and Down buttons to set the
intensity. The adjustment range is between , ,
or .
06) If you choose the strobe settings from the LEDs, press the Up and Down buttons to set the strobe.
The adjustment range is between , from slow to fast and is the soundcontrolled strobe.
18
Ordercode: 43163
Colorburst
07) If you choose the laser settings, press the Up and Down buttons to choose between (no laser
output), (only red output), (only green output) or (red and green output).
08) If you choose the strobe settings from the laser, press the Up and Down buttons to set the strobe.
The adjustment range is between , from slow to fast and is the soundcontrolled strobe.
09) If you choose to set the rotation direction, press the Up and Down buttons to select
(automatic rotation between clockwise and counterclockwise), (clockwise) or
(counterclockwise).
10) If you choose to set the rotation speed, press the Up and Down buttons to set the speed. The
adjustment range is between , from slow to fast.
4. DMX Address / DMX Channels
With this menu you can choose a DMX configuration and set the DMX address.
01) Press the Menu button until the display shows .
02) Press the Enter button, the display will show .
03) Press the Enter button again to open the submenu.
04) Press the Up and Down buttons to choose between , or .
05) Choose the desired configuration and press the Enter button to open the submenu.
06) Press the Up and Down buttons to set the desired DMX address.
07) If you choose the configuration, the adjustment range is between .
08) If you choose the configuration, the adjustment range is between .
09) If you choose the configuration, the adjustment range is between .
5. Slave mode
With this menu you can set the device as a Slave.
01) Press the Menu button until the display shows .
02) Press the Enter button to activate the slave mode, the display shows .
03) If the device has not been set to slave, it is automatically classified as a master device. All slave
devices will follow the master movement. If the device has been set to slave, it will react the same as
its master device.
6. System Settings
With this menu you can set several system functions.
01) Press the Menu button until the display shows .
02) Press the Enter button to open this menu.
03) Press the Up and Down buttons to choose between 4 settings:
LED display on/off
LED display reverse
IR remote control on/off
Reset to default settings
04) If you have chosen , press the Enter button to set the LED display ON or OFF.
05) Press the Up and Down buttons to choose between .
06) If you choose , the display will continuously light up.
07) If you choose , the display will turn off after 40 seconds, the display will show .
08) If you have chosen , press the Enter button to set the display in reverse mode.
19
Ordercode: 43163
Colorburst
09) Press the Up and Down buttons to choose between .
10) If you choose , the text will be displayed normally.
11) If you choose , the text will be displayed reversed.
12) If you have chosen , press the Enter button to activate the IR mode.
13) If you choose , the included IR remote control will not work.
14) If you choose , the included IR remote control will be activated.
15) If you have chosen , press the Enter button to reset to default settings.
16) Press the Up and Down buttons to choose between .
17) To reset the device choose YES.
18) Press the Enter button to confirm.
19) The display will show its version and the device settings have been reset.
20) The device will start up in the Auto Run Programs mode.
Remote Control
Note: buttons , , and have no function
Button
Function
Description
On / Off
Switch the device ON or OFF
Auto Run Mode
Repeatedly press the button to activate the Auto Run
programs ( )
Sound-controlled Mode
Repeatedly press the button to activate the Sound-
controlled programs ( )
Pause
Press the button to pause the built-in programs
Motor Speed
Press one of the buttons to adjust the motor speed. 0 = no
rotation, 99 = fast
Auto Run Programs
Speed
Press one of the two buttons to choose the desired speed
of the desired Auto Run program
Auto/Sound mode switch
Press the button to change the programs between Auto or
Sound mode
20
Ordercode: 43163
Colorburst
DMX Channels
3 channels
Channel 1 – Auto (CH2 must be set between 0-250 ) and
Sound Programs (CH2 must be set between 251-255 )
0-5
No function
6-40
Auto program 1/ Sound program 1
41-76
Auto program 2/ Sound program 2
77-112
Auto program 3/ Sound program 3
113-148
Auto program 4/ Sound program 4
149-184
Auto program 5/ Sound program 5
185-220
Auto program 6/ Sound program 6
221-255
Auto program 7/ Sound program 7
Channel 2 – Speed Auto Programs/ Sensitivity Sound programs (CH1 must be set between 6-255 )
0-250
Gradual adjustment Speed Auto programs from slow to fast
251-255
Sound-controlled, from less sensitivity to maximum sensitivity
Channel 3 – Rotation effect
0-4
No function
5-127
Counterclockwise rotation, from slow to fast
128
Stop
129-255
Clockwise rotation, from slow to fast
10 channels
Channel 1 – Red Dimmer intensity (CH6 must be set between 1-255 )
0-255
Gradual adjustment Red from 0-100%
Channel 2 – Green Dimmer intensity (CH6 must be set between 1-255 )
0-255
Gradual adjustment Green from 0-100%
Channel 3 – Blue Dimmer intensity (CH6 must be set between 1-255 )
0-255
Gradual adjustment Blue from 0-100%
Channel 4 – White Dimmer intensity (CH6 must be set between 1-255 )
0-255
Gradual adjustment White from 0-100%
Channel 5 – LEDs color control (CH6 must be set between 1-255 )
0-5
No function
LED1
LED2
LED3
6-15
Red
Red
Red
16-26
Green
Green
Green
27-37
Blue
Blue
Blue
38-48
White
White
White
49-59
Red
Green
Blue
60-70
Red
Green
White
71-81
Red
Blue
White
82-92
Green
Blue
White
93-103
Red/Green
Red/Blue
Red/White
104-114
Green/Red
Green/Blue
Green/White
21
Ordercode: 43163
Colorburst
115-125
Blue/Red
Blue/Green
Blue/White
126-136
White/Red
White/Green
White/Blue
137-147
Red/Green
Red/Green
Red/Green
148-158
Red/Blue
Red/Blue
Red/Blue
159-169
Red/White
Red/White
Red/White
170-180
Green/Blue
Green/Blue
Green/Blue
181-191
Green/White
Green/White
Green/White
192-202
Blue/White
Blue/White
Blue/White
203-213
Red/Green/Blue
Red/Green/Blue
Red/Green/Blue
214-224
Red/Green/White
Red/Green/White
Red/Green/White
225-235
Green/Blue/White
Green/Blue/White
Green/Blue/White
236-246
Red/Green/Blue
Green/Blue/White
Red/Green/White
247-255
Red/Green/Blue/White
Red/Green/Blue/White
Red/Green/Blue/White
Channel 6 – Master Dimmer intensity LEDs (CH1, CH2, CH3, CH4 or CH5 must be set between 1-255 )
0-255
Dimmer intensity, from dark to brightest
Channel 7 – Strobe LEDs (CH1, CH2, CH3, CH4 or CH5 and CH6 must be set between 1-255 )
0-5
No function
6-250
Strobe flash frequency, from slow to fast
251-255
Sound-activated strobe
Channel 8 – Laser functions (when CH8 is set between 129-255, CH9 must be set between 6-255 )
0-5
No function
6-46
Red laser on
47-87
Green laser on
88-128
Red + Green laser on
129-169
Red laser flashes + Green laser on
170-210
Red laser on + Green laser flashes
211-255
Red + Green laser flash
Channel 9 – Strobe Laser (CH8 must be set between 6-255 )
0-5
No function
6-250
Strobe flash frequency, from slow to fast
251-255
Sound-activated strobe
Channel 10 – Rotation direction and speed
0
No function
1-127
Counterclockwise rotation, from slow to fast
128
Stop
129-255
Clockwise rotation, from slow to fast
22
Ordercode: 43163
Colorburst
22 channels
Channel 1 – Red Dimmer intensity LED 1 (CH17 must be set between 1-255 )
0-255
Gradual adjustment Red from 0-100%
Channel 2 – Green Dimmer intensity LED 1 (CH17 must be set between 1-255 )
0-255
Gradual adjustment Green from 0-100%
Channel 3 – Blue Dimmer intensity LED 1 (CH17 must be set between 1-255 )
0-255
Gradual adjustment Blue from 0-100%
Channel 4 – White Dimmer intensity LED 1 (CH17 must be set between 1-255 )
0-255
Gradual adjustment White from 0-100%
Channel 5 – Strobe LED 1 (CH1, CH2, CH3 or CH4 and CH17 must be set between 1-255 )
0-5
No function
6-250
Strobe flash frequency, from slow to fast
251-255
Sound-activated strobe
Channel 6 – Red Dimmer intensity LED 2 (CH17 must be set between 1-255 )
0-255
Gradual adjustment Red from 0-100%
Channel 7 – Green Dimmer intensity LED 2 (CH17 must be set between 1-255 )
0-255
Gradual adjustment Green from 0-100%
Channel 8 – Blue Dimmer intensity LED 2 (CH17 must be set between 1-255 )
0-255
Gradual adjustment Blue from 0-100%
Channel 9 – White Dimmer intensity LED 2 (CH17 must be set between 1-255 )
0-255
Gradual adjustment White from 0-100%
Channel 10– Strobe LED 2 (CH6, CH7, CH8 or CH9 and CH17 must be set between 1-255 )
0-5
No function
6-250
Strobe flash frequency, from slow to fast
251-255
Sound-activated strobe
Channel 11 – Red Dimmer intensity LED 3 (CH17 must be set between 1-255 )
0-255
Gradual adjustment Red from 0-100%
Channel 12 – Green Dimmer intensity LED 3 (CH17 must be set between 1-255 )
0-255
Gradual adjustment Green from 0-100%
Channel 13 – Blue Dimmer intensity LED 3 (CH17 must be set between 1-255 )
0-255
Gradual adjustment Blue from 0-100%
Channel 14 – White Dimmer intensity LED 3 (CH17 must be set between 1-255 )
0-255
Gradual adjustment White from 0-100%
23
Ordercode: 43163
Colorburst
Channel 15– Strobe LED 3 (CH11, CH12, CH13 or CH14 and CH17 must be set between 1-255 )
0-5
No function
6-250
Strobe flash frequency, from slow to fast
251-255
Sound-activated strobe
Channel 16 – LEDs color control (CH17 must be set between 1-255 )
0-5
No function
LED1
LED2
LED3
6-15
Red
Red
Red
16-26
Green
Green
Green
27-37
Blue
Blue
Blue
38-48
White
White
White
49-59
Red
Green
Blue
60-70
Red
Green
White
71-81
Red
Blue
White
82-92
Green
Blue
White
93-103
Red/Green
Red/Blue
Red/White
104-114
Green/Red
Green/Blue
Green/White
115-125
Blue/Red
Blue/Green
Blue/White
126-136
White/Red
White/Green
White/Blue
137-147
Red/Green
Red/Green
Red/Green
148-158
Red/Blue
Red/Blue
Red/Blue
159-169
Red/White
Red/White
Red/White
170-180
Green/Blue
Green/Blue
Green/Blue
181-191
Green/White
Green/White
Green/White
192-202
Blue/White
Blue/White
Blue/White
203-213
Red/Green/Blue
Red/Green/Blue
Red/Green/Blue
214-224
Red/Green/White
Red/Green/White
Red/Green/White
225-235
Green/Blue/White
Green/Blue/White
Green/Blue/White
236-246
Red/Green/Blue
Green/Blue/White
Red/Green/White
247-255
Red/Green/Blue/White
Red/Green/Blue/White
Red/Green/Blue/White
Channel 17 – Master Dimmer intensity LEDs (CH1- CH16 must be set between 1-255 )
0-255
Dimmer intensity, from dark to brightest
Channel 18 – Laser functions (when CH18 is set between 129-255, CH19 must be set between 6-255 )
0-5
No function
6-46
Red laser on
47-87
Green laser on
88-128
Red + Green laser on
129-169
Red laser flashes + Green laser on
170-210
Red laser on + Green laser flashes
211-255
Red + Green laser flash
Channel 19 – Strobe Laser (CH18 must be set between 6-255 )
0-5
No function
6-250
Strobe flash frequency, from slow to fast
251-255
Sound-activated strobe
24
Ordercode: 43163
Colorburst
Channel 20 – Auto and Sound Programs
0-5
No function
6-40
Auto program 1/ Sound program 1
41-76
Auto program 2/ Sound program 2
77-112
Auto program 3/ Sound program 3
113-148
Auto program 4/ Sound program 4
149-184
Auto program 5/ Sound program 5
185-220
Auto program 6/ Sound program 6
221-255
Auto program 7/ Sound program 7
Channel 21 – Speed Auto Programs/ Sensitivity Sound programs (CH20 must be set between 6-255 )
0-250
Gradual adjustment Speed Auto programs from slow to fast
251-255
Sound-controlled, from less sensitivity to maximum sensitivity
Channel 22 – Rotation direction and speed
0
No function
1-127
Counterclockwise rotation, from slow to fast
128
Stop
129-255
Clockwise rotation, from slow to fast
Maintenance
The Colorburst requires almost no maintenance. However, you should keep the unit clean.
Otherwise, the fixture’s light-output will be significantly reduced. Disconnect the mains power supply, and
then wipe the cover with a damp cloth. Do not immerse in liquid. Wipe lens clean with glass cleaner and
a soft cloth. Do not use alcohol or solvents.
The front lens will require weekly cleaning, as smoke-fluid tends to build up residues, reducing the lightoutput very quickly.
Keep connections clean. Disconnect electric power, and then wipe the DMX and audio connections
with a damp cloth. Make sure connections are thoroughly dry before linking equipment or supplying
electric power.
The operator has to make sure that safety-related and machine-technical installations are to be
inspected by an expert after every year in the course of an acceptance test.
The operator has to make sure that safety-related and machine-technical installations are to be
inspected by a skilled person once a year.
The following points have to be considered during the inspection:
01) All screws used for installing the device or parts of the device have to be tightly connected and
must not be corroded.
02) There may not be any deformations on housings, fixations and installation spots.
03) Mechanically moving parts like axles, eyes and others may not show any traces of wearing.
04) The electric power supply cables must not show any damages or material fatigue.
Replacing the Fuse
Power surges, short-circuit or inappropriate electrical power supply may cause a fuse to burn out.
If the fuse burns out, the product will not function whatsoever. If this happens, follow the directions below:
01) Unplug the unit from electric power source.
02) Insert a flat-headed screwdriver into a slot in the fuse cover. Gently pry up the fuse cover.
the fuse will come out.
03) Remove the used fuse. If brown or unclear, it is burned out.
04) Insert the replacement fuse into the holder. Reinsert the fuse cover. Be sure to use a fuse of the
same type and specification. See the product specification label for details.
25
Ordercode: 43163
Colorburst
Troubleshooting
This troubleshooting guide is meant to help solve simple problems.
If a problem occurs, carry out the steps below in sequence until a solution is found. Once the unit
operates properly, do not carry out following steps.
No Light
If the light effect does not operate properly, refer servicing to a technician.
Suspect four potential problem areas as: the power supply, the laser, LEDs, the fuse.
01) Power supply. Check that the unit is plugged into an appropriate power supply.
02) The laser. Return the Colorburst to your Showtec dealer.
03) The LEDs. Return the Colorburst to your Showtec dealer.
04) The fuse. Replace the fuse. See page 24 for replacing the fuse.
05) If all of the above appears to be O.K., plug the unit in again.
06) If you are unable to determine the cause of the problem, do not open the Colorburst, as this may
damage the unit and the warranty will become void.
07) Return the device to your Showtec dealer.
No Response to DMX
Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card malfunction.
01) Check the DMX setting. Make sure that DMX addresses are correct.
02) Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power.
Try your DMX control again.
03) Determine whether the controller or light effect is at fault. Does the controller operate properly with
other DMX products? If not, take the controller in for repair. If so, take the DMX cable and the light
effect to a qualified technician.
The fixture does not work, no laser and the fan does not work
01) Check the connected power and main fuse.
02) Check the mains voltage on the main connector.
The fixture is power on, but no laser coming out from aperture
01) Check the laser aperture cover.
02) Check the key switch.
03) Check the remote interlock or interlock connector.
04) Wait for at least 30 minutes to warm up in low temperature.
05) Check whether the fixture is in music mode without sound signal.
06) Check whether the fixture it is in Slave mode.
07) Check whether the fixture is in DMX mode without a DMX signal being present.
The laser effect power is very weak
01) Wait for at least 30 minutes to warm up in low temperature.
02) Clean the scanner mirror with alcohol.
03) Clean the aperture glass with alcohol.
04) Check whether the fixture is in DMX mode with a high strobe frequency.
The laser is on, but the pattern is not moving
01) Check to see whether the fixture is in Music/Sound mode without detecting sound signal.
02) Check to see whether the fixture is in DMX mode.
03) Try to change the fixture to another stand-alone mode.
04) Try to control the fixture via DMX to see the laser effect system.
26
Ordercode: 43163
Colorburst
Problem
Probable cause(s)
Solution
One or more
fixtures do not
function at all
No power to the fixture
• Check if power is switched on and
cables are plugged in
Primary fuse blown.
• Replace fuse.
Fixtures reset
correctly, but all
respond
erratically or not
at all to the
controller
The controller is not connected.
• Connect controller.
3-pin XLR Out of the controller
does not match XLR Out of the first
fixture on the link (i.e. signal is
reversed)
• Install a phase reversing cable
between the controller and the
first fixture on the link
Fixtures reset
correctly, but
some respond
erratically or not
at all to the
controller
Poor data quality
• Check data quality. If much lower
than 100 percent, the problem
may be a bad data link
connection, poor quality or
broken cables, missing termination
plug, or a defective fixture
disturbing the link
Bad data link connection
• Inspect connections and cables.
Correct poor connections. Repair
or replace damaged cables
Data link not terminated with 120
Ohm termination plug
• Insert termination plug in output
jack of the last fixture on the link
Incorrect addressing of the fixtures
• Check address setting
One of the fixtures is defective and
disturbs data transmission on the
link
• Bypass one fixture at a time until
normal operation is restored:
unplug both connectors and
connect them directly together.
• Have the defective fixture
serviced by a qualified technician
3-pin XLR Out on the fixtures does
not match (pins 2 and 3 reversed)
• Install a phase-reversing cable
between the fixtures or swap pin 2
and 3 in the fixture that behaves
erratically
Shutter closes
suddenly
The laser diode has lost its index
position and the fixture is resetting
the effect.
• Contact a technician for servicing
the problem persists.
No light or LEDs or
Laser cuts out
intermittently
Fixture is too hot
• Allow the fixture to cool down
• Clean the fan
• Make sure air vents in control
panel and the front lens are not
blocked
• Turn up the air conditioning
LEDs or Laser damaged
• Disconnect the fixture and return it
to your dealer
The power supply settings do not
match local AC voltage and
frequency
• Disconnect fixture. Check settings
and correct if necessary
27
Ordercode: 43163
Colorburst
Product Specifications
Model:
Showtec Colorburst
Input Voltage:
100-240V AC, 50/60Hz
Power consumption:
63W (full output)
DMX linking:
30 pcs
Power linking @110V
12 pcs
Power linking @240V
21 pcs
Protection rate:
IP-20
Fuse:
T1.6L/250V
Dimensions:
320 x 320 x 400 mm (LxWxH)
Weight:
3,8 kg
Operating and Programming:
Signal pin OUT:
Pin 1 (earth), pin 2 (-), pin 3 (+)
DMX Mode:
3, 10 or 22 channels
Signal input:
3-pin DMX IN
Signal output:
3-pin DMX OUT
Electro-mechanical effects:
LED Spot effect:
5 x 8W RGBW LEDs
Laser effect:
Colors: Red, Green
Power: 135mW (100mW 650nm Red, 35mW 532nm
Green)
Class: 2M
Safety Features: Key switch, Interlock, Safety eye
Safety: EN/IEC 60825-1 Ed 2, 2007-03
Housing:
Die-cast black aluminum
DMX-control:
via standard DMX-controller
On Board:
4-digit LED display for easy setup
Control:
Auto, Sound-controlled, Static color, Master/Slave, DMX
Connections:
IEC connectors (IN/OUT), 3-pin XLR (IN/OUT)
Cooling:
Fans/Convection
Max. ambient temperature ta:
40°C
Max. housing temperature tB:
80°C
Minimum distance:
Minimum distance from flammable surfaces:
0,5 m
Minimum distance to lighted object:
1 m
Design and product specifications are subject to change without prior notice.
Website: www.Showtec.info
Email: service@highlite.nl
28
Ordercode: 43163
Colorburst
Dimensions
29
Ordercode: 43163
Colorburst
Notes
30
Ordercode: 43163
Colorburst
©2018 Showtec
Loading...