SHOWTEC 42199 User Manual
LED light bar 8 V2
Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
Ordercode: 42199
MANUAL
ENGLISH
Ordercode: 42199
LED Light Bar 8
Table of contents
Warning ............................................................................................................................................................................... 2
Safety Instructions ......................................................................................................................................................... 2
Operating Determinations .......................................................................................................................................... 4
Rigging ............................................................................................................................................................................ 4
Connection with the mains ......................................................................................................................................... 4
Return Procedure .......................................................................................................................................................... 5
Claims .............................................................................................................................................................................. 5
Description of the device ................................................................................................................................................. 6
Optional accessories .................................................................................................................................................... 6
Overview ........................................................................................................................................................................ 7
Installation ........................................................................................................................................................................... 7
Set Up and Operation ....................................................................................................................................................... 7
Control Modes ............................................................................................................................................................... 7
One Light Bar (Manual control) ............................................................................................................................. 7
One Light Bar (Built-in programs,Macro colors) .................................................................................................. 8
One Light Bar (Sound-control) ................................................................................................................................ 8
Multiple Light Bars (Master/Slave control) ............................................................................................................. 8
Multiple Light Bars (DMX512 Mode) ....................................................................................................................... 9
Fixture Linking ...............................................................................................................................................................10
Data Cabling ...............................................................................................................................................................10
Control Panel ...............................................................................................................................................................11
DMX Control Mode .....................................................................................................................................................11
DMX Addressing ..........................................................................................................................................................11
Menu overview ................................................................................................................................................................12
Main Menu Options ....................................................................................................................................................14
1. DMX Mode ...............................................................................................................................................................14
2. Master / slave addressing .....................................................................................................................................14
3. Sound control Mode ..............................................................................................................................................15
4. Static Color Mode ..................................................................................................................................................15
5. Built-in Programs ......................................................................................................................................................15
6. Auto Run Program ..................................................................................................................................................18
DMX Channels .............................................................................................................................................................19
3 DMX Channels (d-P1) ...........................................................................................................................................19
4 DMX Channels (d-P2). ..........................................................................................................................................19
14 DMX Channels (d-P3).........................................................................................................................................19
26 DMX Channels (d-P4).........................................................................................................................................20
2 DMX Channels (d-P5) ...........................................................................................................................................22
7 DMX Channels (d-P6) ...........................................................................................................................................23
Maintenance ....................................................................................................................................................................24
Replacing a Fuse ........................................................................................................................................................24
Troubleshooting ...............................................................................................................................................................25
No Light .........................................................................................................................................................................25
No Response to DMX ..................................................................................................................................................25
Product Specifications ....................................................................................................................................................27
Dimensions ........................................................................................................................................................................28
Notes ..................................................................................................................................................................................29
1
Ordercode: 42199
LED Light Bar 8
Your shipment includes:
Showtec LED Light Bar 8
• 2 brackets and screws
• Volex IEC powercable 1,5m
• User manual
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear to be damaged from shipping or the carton
itself shows signs of mishandling. Save the carton and all packing materials. In the event that the fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box and
packing.
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving the lifespan is of higher priority, place care in providing for lower
operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
● be qualified
● follow the instructions of this manual
Before your initial start-up, please make sure that there is no damage caused by transportation. Should
there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty. This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
2
Ordercode: 42199
LED Light Bar 8
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
Never remove warning or informative labels from the unit.
Never use anything to cover the ground contact.
Never place any material over the lens.
Never look directly into the light source.
Never leave any cables lying around.
Do not insert objects into air vents.
Do not connect this device to a dimmerpack.
Do not switch the device on and off in short intervals, as this would reduce the device’s lifespan.
Do not touch the device’s housing bare-handed during its operation. Allow the fixture to cool for at
least 5 minutes before handling.
Do not shake the device. Avoid brute force when installing or operating the device.
Only use device indoor, avoid contact with water or other liquids.
Only operate the fixture after having checked that the housing is firmly closed and all screws are
tightly fastened.
Only operate the device after having familiarized with its functions.
Avoid flames and do not put close to flammable liquids or gases.
Always keep case closed while operating.
Always allow free air space of at least 50 cm around the unit for ventilation.
Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord by the plug. Never pull out the plug by tugging the power cord.
Make sure that the device is not exposed to extreme heat, moisture or dust.
Make sure that the available voltage is not higher than stated on the rear panel.
Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
If the lens is obviously damaged, it has to be replaced to prevent its functions from being impaired,
due to cracks or deep scratches.
If device was dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
For adult use only. Device must be installed out of reach of children. Never leave the unit running
unattended.
Never attempt to bypass the thermostatic switch or fuses.
For replacement, use fuses of same type and rating only.
The user is responsible for correct positioning and operating of the Light Bar 8.
The manufacturer will not accept liability for damages caused by the misuse or incorrect installation
of this device.
This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
Repairs, servicing and electrical connection must be carried out by a qualified technician.
WARRANTY: Till one year after date of purchase.
3
Ordercode: 42199
LED Light Bar 8
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE GROUND
Operating Determinations
● This device is not designed for permanent operation. Regular operation breaks will ensure that the
device will serve you for a long time without defects.
● The minimum distance between light-output and the illuminated surface must be bigger than 1
meter.
● The maximum ambient temperature ta = 40°C must never be exceeded.
● The relative humidity must not exceed 50 % with an ambient temperature of 40° C.
● If this device is operated in any other way than the one described in this manual, the product may
suffer damages and the warranty becomes void.
● Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself!
Always let the installation be carried out by an authorized dealer!
Procedure:
If the projector is lowered from the ceiling or high joists, professional trussing systems have to be
used.
Use a clamp to mount the projector, with the mounting-bracket, to the trussing system.
The projector must never be fixed swinging freely in the room.
The installation must always be secured with a safety attachment, e.g. an appropriate safety net
or safety-cable.
When rigging, derigging or servicing the projector, always make sure, that the area below the
installation place is blocked and staying in the area is forbidden.
The Light Bar 8 can be placed on a flat stage floor or mounted to any kind of truss by a clamp.
Improper installation can cause serious injuries and/or damage of property!
Connection with the mains
Connect the device to the mains with the power plug.
Always check if the right color cable is connected to the right place.
Make sure that the device is always connected properly to the earth!
Improper installation can cause serious damage to people and property!
4
Ordercode: 42199
LED Light Bar 8
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail aftersales@highlite.nl and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause of the
return. Be sure to properly pack fixture as any shipping damage resulting from inadequate packaging is
the customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name.
02) Your address.
03) Your phone number.
04) A brief description of the symptoms.
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any shortcomings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that the fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
agreed otherwise in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the
invoice. After this period, complaints will not be handled anymore.
Complaints will only be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of which the obligation is resulting.
5
Ordercode: 42199
LED Light Bar 8
Description of the device
Features
The LED Light Bar 8 is a LED fixture from Showtec.
• LEDs: 240 RGB high intensity 10mm LEDs (Red 96, Green 72, Blue 72)
• Beam angle: 30 º
• Inexpensive batten effect
• 8 sections
• Compact size
• Output: 800Lumen
• Lux @2m: 613,3
• Max. Distance: 15m
• Efficacy (lm/W) 36W
• Drive Current: 25mA
• Refresh rate: 400Hz
• Color Range: RGB
• Power Supply: 100-240V AC
• Control Mode: DMX512
• Dimmer: 0-100%
• Strobe: 0-20Hz
• Peak Power 130 Watt
• Continuous Power 60 Watt
• 3 pin female XLR socket and 3 pin male XLR socket
• IEC Power In and IEC power Out (Max. 10A)
• Linkable via 3-pin XLR cable
• Built-in microphone
• Black aluminum material
• LED Digital display
• Fuse: 1A / 250V
• Built-in programs mode, Auto running mode, DMX mode, slave mode, sound-activated mode.
• DMX controlled
• Selectable 2, 3, 4, 7, 14 and 26 DMX channel operation
• Dimensions: 1070 x 65 x 88 mm (LXWXH)
• Weight: 1,74 kg
Note: Knowledge of DMX is required to fully utilize this unit.
Optional accessories
D7012 Flightcase for LED Light Bar 8
D7595 Flightcase for LED Light Bar 8
70109B Heavy Duty Pipe Clamp, SWL=35 kg
70359B 50 mm Quick coupler
70365B 50 mm Compact Half Coupler
6
Ordercode: 42199
LED Light Bar 8
Fig. 01
There are 6 modes:
Manual control (Static)
Built-in Programs
Macro Colors (Auto Run)
Sound-controlled
Master/Slave
DMX512
Overview
01) Adjustment screw + mounting bracket for Truss mounting
02) IEC Power In
03) Ground
04) Fuse 1A / 250V
05) Total LED Light Bar 240 LEDs
06) Menu Buttons + LED display
07) DMX signal connector (IN) 3-pin
08) DMX signal connector (OUT) 3-pin
09) IEC Power Out (Max. 10A)
Installation
Remove all packing materials from the LED Light Bar 8.
Check that all foam and plastic padding is removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Connect the device to the main power supply.
Control Modes
One Light Bar (Manual control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) When the Light Bar is not connected by a DMX-cable, it functions as a stand-alone device.
03) If device is set to , then the fixture can be manually controlled.
04) Please see page 15 for more information about manual control Mode.
7
Ordercode: 42199
LED Light Bar 8
The pins:
1. Earth
2. Signal (-)
3. Signal (+)
Fig. 02
One Light Bar (Built-in programs,Macro colors)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) When the Light Bar is not connected by a DMX-cable, it functions as a stand-alone device.
03) If device is set to or , then the fixture will play one of its built-in programs or show
one of its macro colors. Please see pages 15-18 for more information about the built-in programs or
macro colors.
One Light Bar (Sound-control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) When the Light Bar is not connected by a DMX-cable, it functions as a stand-alone device.
03) Turn on the music. If device is set to (Audio) and you have pressed enter, then the fixture
will react to the beat of the music. Please see page 15 for more information about the Sound-
controlled mode.
Multiple Light Bars (Master/Slave control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Plug the end of the electric mains power cord into a proper electric power supply socket.
03) Use a 3-p XLR cable to connect the Light Bar and other devices.
04) Link the units as shown in (Fig. 02), connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second, and third units. You can use the
same functions on the master device as described on page 14-17 (Built-in Programs). This means you
can set your desired operation mode on the master device and all slave devices will react the same
as the master device.
Multiple Light Bars (Master/Slave control)
8
Ordercode: 42199
LED Light Bar 8
Fig. 03
Multiple Light Bars (DMX512 Mode)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Plug the end of the electric mains power cord into a proper electric power supply socket.
03) Use a 3-p XLR cable to connect the Light Bar and other devices.
04) Link the units as shown in (Fig. 03), Connect a DMX signal cable from the first unit's DMX "out" socket
to the second unit's "in" socket. Repeat this process to link the second and third units.
05) Supply electric power: Plug electric mains power cords into each unit's IEC socket, then plug the
other end of the mains power cord into proper electric power supply sockets, starting with the first
unit. Do not supply power before the whole system is set up and connected properly.
Multiple Light Bars DMX Set Up
Note: Link all cables before connecting electric power!
9
Loading...