ShoreLand'r SLXR40TCBXLW User Manual
SLXR40TCBXLW-__ & SLXR40TCBBXLW-__
SLXR40TCBXLW-__ Shown
SLXR40TCBXLW Bundles Required:
66520 Bag with Chains, No Coupler.....................1
69082 Lit Packet Brake Trailers............................1
80780-- Frame Bundle - 2X4W XR40TCBLW.........1
66996-- Tongue Assembly 55”, W/UFP Actuator....1
TA0991-__ Winch Stand Kit 9” W/Mtg Hdwe…….……1
TA0992-__ Winch Stand Kit 9” W/Mtg Hdwe……….…1
TA0993-__ Winch Stand Kit 7” W/Mtg Hdwe…….……1
ST215/75R14C Tire/TS Dir Rim................4
(or)
ST215/75R14C Tire/Galv Dir Rim..............4
(or)
(or)
SLXR40TCBBXLW Bundles Required:
ST215/75R14C Tire/TS Dir Rim................4
(or)
ST215/75R14C Tire/Galv Dir Rim..............4
66520 Bag with Chains, No Coupler.....................1
69082 Lit Packet Brake Trailers............................1
80781-- Frame Bundle - 2X4W XR40TCBBLW......1
66996-- Tongue Assembly 55”, W/UFP Actuator....1
69352 Brake Kit Tandem Axle Connect………….1
TA0991-__ Winch Stand Kit 9” W/Mtg Hdwe……….…1
(or)
TA0992-__ Winch Stand Kit 9” W/Mtg Hdwe……….…1
(or)
TA0993-__ Winch Stand Kit 7” W/Mtg Hdwe……….…1
ShoreLand’r offers their product line in either galvanized or painted finis h. When ordering parts it is important that you
specify the finish or color you have on your prod uct. The five (5) digit number along with a two (2) digit space _ _, no te
the parts which can be purchased with various finishes. When ordering these items use the five (5) digit number along
with a two (2) digit suffix for the proper finish.
00..........Galvanized
01..........Arctic White
03..........Black
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004281
Page 1 of 16 10/28/2010
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004281
Page 2 of 16 10/28/2010
FINAL ASSEMBLY INSTRUCTIONS
Remove the hardware bag from the frame, remove
parts and sort by size.
TONGUE
The tongue is shipped separate of the frame. Locate
the appropriate tongue and install by sliding it in the
front of the tongue channel.
Line the holes in the tongue with the holes in the
tongue channel. Install the 1/2” x 4” hex bolt in the
front cross hole and secure with a 1/2” lock nut.
Remove the wire harness from the rear of the tongue.
Place the wire harness and the brake line through the
hole provided in the tongue cover plate.
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004281
Page 3 of 16 10/28/2010
See Detail A in Diagram A. Secure the tongue cover plate in position
with the same 1/2” x 1-1/2” hex bolt that secures the back on the
tongue to the tongue channel of the frame. Secure with 1/2” lock nut.
Tighten both bolts just installed.
Plug the tongue wire harness ends into the frame harnesses by
matching colors and ends. Push the extra wire provided into the rear
of the tongue or remove the grommet in the side frame and place the
extra wire in the side frame. Replace grommet just removed.
SAFETY CHAINS
Locate the 1/2” x 1-1/4” hex bolt. Slip the bolt through a 1/2” at washer, then
place through the last link of one of the safety chains. Place a second flat
washer on the bolt and insert through the hole as shown in Diagram B. Secure
with a 1/2” flange lock nut. Tighten. Repeat this process on the second safety
chain on the opposite side of the tongue. Assembly is complete.
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004281
Page 4 of 16 10/28/2010
WINCH POST ASSEMBLY
The height that the bow eye is placed in your boat will
determine the length winch post required. Once this is
determined, attach the winch base to the tongue with
three 1/2” x 4-1/2” carriage bolts and lock nuts.
Align the holes in the Profile 2000 mounting channel
with the holes in the top of the winch base. Attach the
front of the winch head mounting channel to the base by
placing a 1/2” x 4-1/2” hex bolt through the hole closest
to the front of the winch base. Secure with a lock nut. Do
not tighten.
Note that the winch head can now be rotated either up
or down. Identify the correct hole combination to use
to position the bow eye roller just above the bow eye
of your boat. When determined, secure in this position
by placing the bushing as shown in Diagram C inside
the winch base so it aligns with the hole just identified
for the proper adjustment. Insert another 1/2” x 4-1/2”
hex bolt through the determined mounting hole in the
mounting channel and winch base making sure the
bolt passes through the bushing as well. Secure with
a 1/2” lock nut.
Tighten all bolts.
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004281
Page 5 of 16 10/28/2010
Loading...