Page 1
READ THIS FIRST
163V2 X1767163V2 CRANK HANDWHEEL V2.06.18
Model W1767
***IMPORTANT UPDATE***
Applies to Models Mfd. Since 6/18
and Owner's Manual Revised 4/14
Phone #: (360) 734-3482 • Tech Support: [email protected] • Web: www.woodstockint.com
We made the following change to this machine since the manual was printed:
• Updated Stand parts breakdown.
Aside from the information contained in this update, all other content in the owner's manual is
applicable and MUST be read and understood for your own safety.
IMPORTANT: Keep this update with the owner's manual for future reference. If you have any further
questions, contact our Technical Support.
Revised Stand Parts Breakdown
163V2
104V2
134
REF PART # DESCRIPTION
104V2 X1767104V2 T-HANDLE V2.06.18
134 X1767134 ROLL PIN 6 X 22
141V2 X1767141V2 SHOULDER LOCK STUD V2.06.18
141V2
COPYRIGHT © JULY, 2018 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
Printed in Taiwan#19752MN
Page 2
MODEL W1767
1 HP POWER FEEDER
OWNER'S MANUAL
(FOR MODELS MANUFACTURED SINCE 08/15)
Phone: (360) 734-3482 • Online Technical Support: [email protected]
COPYRIGHT © SEPTEMBER, 2007 BY WOODSTOCK INTERNATIONAL, INC. REVISED JUNE, 2018 (HE)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#9785CR Printed in Taiwan V4.06.18
Page 3
This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and comprehension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property
damage from negligence, improper training, machine modifications or
misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement and other masonry products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter
out microscopic particles.
Page 4
Contents
INTRODUCTION ..................................................................................................2
Woodstock Technical Support ............................................................................ 2
SAFETY ............................................................................................................6
Standard Machinery Safety Instructions ................................................................ 6
Additional Safety for Power Feeders ....................................................................8
ELECTRICAL ......................................................................................................9
Circuit Requirements ...................................................................................... 9
Grounding Requirements ................................................................................ 10
Extension Cords .......................................................................................... 10
SETUP ........................................................................................................... 11
Unpacking ................................................................................................. 11
Inventory .................................................................................................. 11
Cleaning Machine......................................................................................... 12
Assembly ................................................................................................... 13
Base Mounting ............................................................................................ 14
Test Run .................................................................................................... 16
OPERATIONS ................................................................................................... 17
General .................................................................................................... 17
Changing Feed Speed .................................................................................... 18
Power Feeder Accessories .............................................................................. 19
MAINTENANCE ................................................................................................. 21
General .................................................................................................... 21
Cleaning ................................................................................................... 21
Lubrication ................................................................................................ 21
SAFETYINTRODUCTION
SET UPELECTRICAL MAINTENANCE
OPERATIONS
SERVICE ......................................................................................................... 22
General .................................................................................................... 22
Wheel Replacement ..................................................................................... 22
Troubleshooting........................................................................................... 23
Electrical Safety Instructions ........................................................................... 24
Wiring Diagram ........................................................................................... 25
PARTS ........................................................................................................... 26
Main Breakdown .......................................................................................... 26
Stand Breakdown ......................................................................................... 28
Labels & Cosmetics ...................................................................................... 29
Notes ....................................................................................................... 30
WARRANTY ..................................................................................................... 33
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!
SERVICE PARTS
Page 5
Model W1767 (For Machines Mfd. Since 08/15)
INTRODUCTION
INTRODUCTION
Woodstock Technical Support
Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to
include the basic information for safety, setup, operation, maintenance, and service of this product.
In the event that questions arise about your machine, please contact Woodstock International Technical
Support at (360) 734-3482 or send e-mail to: [email protected]. Our knowledgeable staff will
help you troubleshoot problems or process warranty claims.
If you need the latest edition of this manual, you can download it from http://www.shopfox.biz.
If you have comments about this manual, please contact us at:
Woodstock International, Inc.
Attn: Technical Documentation Manager
P.O. Box 2309
Bellingham, WA 98227
Email: [email protected]
-2-
Page 6
Model W1767 (For Machines Mfd. Since 08/15)
MACHINE
SPECIFICATIONS
Phone #: (360) 734–3482 • Online Tech Support: tech–[email protected] • Web: www.shopfox.biz
MOdEl W1767
1 HP POWER FEEdER
Motor
Type ..........................................................................................TEFC Capacitor Start Induction
Horsepower ................................................................................................................. 1 HP
Voltage ......................................................................................................................220V
Prewired ..................................................................................................................... 220V
Phase ....................................................................................................................... Single
Amps .................................................................................................................... 4.2/2.5A
Speed ........................................................................................................... 3450/1725 RPM
Cycle ........................................................................................................................ 60 Hz
Number of Speeds ............................................................................................................. 2
Power Transfer ...................................................................................................... Gear Box
Bearings ................................................................................................... Lubricated for Life
INTRODUCTION
Main Specifications
Operation Info
Minimum Workpiece Length ....................................................................................... 7 in.
Number of Feed Speeds ................................................................................................ 4
Feed Speeds .........................................................................................13, 26, 33, 66 FPM
Swing ............................................................................................................ 360 deg.
Vertical Movement ............................................................................................. 9-7/8 in.
Horizontal Movement ........................................................................................ 18-1/8 in.
Rotation ............................................................................................... Forward, Reverse
Roller Info
Number of Rollers ....................................................................................................... 3
Roller Width .....................................................................................................2–3/8 in.
Roller Diameter ................................................................................................. 4–3/4 in.
Roller Suspension ................................................................................................. 3/4 in.
Maximum Height of Rollers ................................................................................... 8-1/2 in.
Distance Between Rollers .......................................................................................... 5 in.
Overall Dimensions
Weight............................................................................................................. 130 lbs.
Length/Width/Height ..................................................................................44 x 16 x 30 in.
Column Diameter ...............................................................................................2-1/4 in.
Construction Materials
Roller Construction ................................................................................. Synthetic Rubber
Housing Construction .................................................................................. Cast Aluminum
Supports Construction .........................................................................................Cast Iron
Column Construction .............................................................................................. Steel
Paint ................................................................................................................. Epoxy
-3-
Page 7
INTRODUCTION
Model W1767 (For Machines Mfd. Since 08/15)
Shipping Dimensions
Carton #1
Type ............................................................................................................ Cardboard
Content ...........................................................................................................Machine
Weight...............................................................................................................63 lbs.
Length/Width/Height ................................................................................. 21 x 12 x 22 in.
Carton #2
Type ............................................................................................................ Cardboard
Content ..............................................................................................................Stand
Weight...............................................................................................................79 lbs.
Length/Width/Height ..................................................................................30 x 13 x 12 in.
Electrical
Switch ..............................................................................Forward/Reverse Barrel with 2 Speeds
Switch Voltage ............................................................................................................ 220V
Cord Length ................................................................................................................. 9 ft.
Cord Gauge ............................................................................................................16 gauge
Recommended Breaker Size .............................................................................................. 15A
Plug ............................................................................................................................Ye s
Other
ISO Factory ............................................................................................................ ISO 9001
Country of Origin ...................................................................................................... Taiwan
Warranty ................................................................................................................ 2 Years
Assembly Time .................................................................................................... 45 minutes
Optional Accessories
Extra Gear ........................................................................................................ Model D3886
Flange Wheel with Rubber Roller ............................................................................. Model D3720
Flange Wheel with Poly Roller ................................................................................. Model D3721
Features
Spring Tensioned Rollers
Heavy–Duty Gear Reduction Gearbox with Hardened Gears
Universal Positioning with Handle Locks
Rack and Pinion System for Horizontal Movement
-4-
Page 8
Model W1767 (For Machines Mfd. Since 08/15)
Controls and Features
Vertical Travel
Vertical
Travel
Lock
Handcrank
Horizontal
Travel Lock
INTRODUCTION
1 HP 2-Speed
Motor
Upper Elbow
Joint Lock
Horizontal
Handwheel
Rotary
Movement
Lock
Gearbox Oil
Plug Labeled
"OIL" Located
on Top of Case
Behind Motor
Lower Elbow
Joint Lock
Figure 1. Controls and Features.
-5-
Page 9
Model W1767 (For Machines Mfd. Since 08/15)
SAFETY
OWNER’S MANUAL.
TRAINED OPERATORS ONLY.
DANGEROUS ENVIRONMENTS.
MENTAL ALERTNESS REQUIRED.
electrical components or improperly grounded
manual uses a series of symbols and signal words intended to convey the level of importance of the
safety messages. The progression of symbols is described below. Remember that safety messages by
SAFETY
For Your Own Safety,
Read Manual Before Operating Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This
SAFETY
themselves do not eliminate danger and are not a substitute for proper accident prevention measures—this responsibility is ultimately up to the operator!
NOTICE
Standard Machinery Safety Instructions
Standard Machinery Safety Instructions
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury.
This symbol is used to alert the user to useful information about
proper operation of the equipment or a situation that may cause
damage to the machinery.
Read and understand this
owner’s manual BEFORE using machine.
have a higher risk of being hurt or killed. Only
allow trained/supervised people to use this
machine. When machine is not being used,
disconnect power, remove switch keys, or
lock-out machine to prevent unauthorized
use—especially around children. Make
workshop kid proof!
machinery in areas that are wet, cluttered,
or have poor lighting. Operating machinery
in these areas greatly increases the risk of
accidents and injury.
alertness is required for safe operation of
machinery. Never operate under the influence
of drugs or alcohol, when tired, or when
distracted.
Untrained operators
Do not use
Full mental
ELECTRICAL EQUIPMENT INJURY RISKS. You can
be shocked, burned, or killed by touching live
machinery. To reduce this risk, only allow an
electrician or qualified service personnel to
do electrical installation or repair work, and
always disconnect power before accessing or
exposing electrical equipment.
DISCONNECT POWER FIRST. Always disconnect
machine from power supply BEFORE making
adjustments, changing tooling, or servicing
machine. This eliminates the risk of injury
from unintended startup or contact with live
electrical components.
EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating
or observing machinery to reduce the risk of
eye injury or blindness from flying particles.
Everyday eyeglasses are not approved safety
glasses.
-6-
Page 10
Model W1767 (For Machines Mfd. Since 08/15)
WEARING PROPER APPAREL. Do not wear
HAZARDOUS
HEARING PROTECTION.
REMOVE ADJUSTING TOOLS.
INTENDED USAGE.
AWKWARD POSITIONS.
CHILDREN & BYSTANDERS.
GUARDS & COVERS.
FORCING MACHINERY. Do not force machine. It
will do the job safer and better at the rate for
loss of control. Before starting, verify machine
malfunction, leading to serious personal injury
from heated surfaces, high traffic areas, harsh
clothing, apparel, or jewelry that can become
entangled in moving parts. Always tie back
or cover long hair. Wear non-slip footwear to
avoid accidental slips, which could cause loss
of workpiece control.
DUST. Dust created while using
machinery may cause cancer, birth defects,
or long-term respiratory damage. Be aware of
dust hazards associated with each workpiece
material, and always wear a NIOSH-approved
respirator to reduce your risk.
Always wear hearing
protection when operating or observing
loud machinery. Extended exposure to this
noise without hearing protection can cause
permanent hearing loss.
machinery can become dangerous projectiles
upon startup. Never leave chuck keys,
wrenches, or any other tools on machine.
Always verify removal before starting!
intended purpose—never make modifications
without prior approval from Woodstock
International. Modifying machine or using
it differently than intended will void the
warranty and may result in malfunction or
mechanical failure that leads to serious
personal injury or death!
balance at all times when operating machine.
Do not overreach! Avoid awkward hand
positions that make workpiece control difficult
or increase the risk of accidental injury.
bystanders at a safe distance from the work
area. Stop using machine if they become a
distraction.
Only use machine for its
Tools left on
Keep proper footing and
Keep children and
which it was designed.
NEVER STAND ON MACHINE. Serious injury may
occur if machine is tipped or if the cutting
tool is unintentionally contacted.
STABLE MACHINE. Unexpected movement during
operation greatly increases risk of injury or
is stable and mobile base (if used) is locked.
USE RECOMMENDED ACCESSORIES. Consult
this owner’s manual or the manufacturer for
recommended accessories. Using improper
accessories will increase risk of serious injury.
UNATTENDED OPERATION. To reduce the risk
of accidental injury, turn machine OFF and
ensure all moving parts completely stop
before walking away. Never leave machine
running while unattended.
MAINTAIN WITH CARE. Follow all maintenance
instructions and lubrication schedules to
keep machine in good working condition. A
machine that is improperly maintained could
or death.
CHECK DAMAGED PARTS. Regularly inspect
machine for any condition that may affect
safe operation. Immediately repair or replace
damaged or mis-adjusted parts before
operating machine.
MAINTAIN POWER CORDS. When disconnecting
cord-connected machines from power, grab
and pull the plug—NOT the cord. Pulling the
cord may damage the wires inside, resulting
in a short. Do not handle cord/plug with wet
hands. Avoid cord damage by keeping it away
chemicals, and wet/damp locations.
SAFETY
accidental contact with moving parts or flying
debris—make sure they are properly installed,
undamaged, and working correctly.
Guards and covers reduce
EXPERIENCING DIFFICULTIES. If at any time
you experience difficulties performing the
intended operation, stop using the machine!
-7-
Contact Technical Support at (360) 734-3482.
Page 11
Model W1767 (For Machines Mfd. Since 08/15)
ATTACHED MACHINERY.
HAND SAFETY
INSTALLING GUARDS.
KICKBACK.
VERIFY EACH SETUP.
workpiece. Stop power feeder before stopping
continuously during operation as required. Use
MAIN INJURY HAZARDS: Death, amputation, or crushing injuries from getting entangled in
Additional Safety for Power Feeders
moving parts—which may include being pulled into the cutting tool on attached machinery;
death, blindness, broken bones, or bruises from being struck by an ejected workpiece
(kickback). To minimize your risk of these hazards, always heed the following information:
Follow all warnings and
SAFETY
safety information for the attached machine
doing the cutting work.
. Keep hands away from rotating
parts on power feeder and spinning blade
or cutter of associated machine. Turn power
feeder and associated machine OFF and only
use a brush or compressed air to remove
sawdust.
Install guards, fences, and
hold-downs before starting attached machine
or power feeder. Repair or replace guards
promptly if they become damaged.
Occurs when workpiece is ejected
from machine with great force, striking
operator or bystanders. Commonly caused by
improper machine or power feeder setup.
Ensure that power feeder
is set up correctly and firmly secured before
feeding workpiece. An improperly adjusted
power feeder could increase the risk of
kickback, because it will continue feeding
when stock is not properly positioned for the
cut.
FEATHERBOARD. When cutting long or large
stock that is difficult to feed properly, use
a featherboard before powerfeeder (on the
infeed side) to maintain even pressure and
control of workpiece against fence, and help
reduce risk of kickback.
FEED WORKPIECE PROPERLY. Verify blade or
cutter of associated machine is at full speed
before feeding stock with power feeder.
Do not feed workpiece too quickly. Verify
power feeder wheels are slightly lower than
cutting tool.
WORKPIECE SUPPORT. Support workpiece
auxiliary stands or support tables for long or
wide stock.
ADJUSTMENTS/MAINTENANCE. Make sure power
feeder is turned OFF, disconnected from
power, and all moving parts are completely
stopped before doing adjustments or
maintenance.
READ and understand this
entire manual before using
this machine. Serious personal injury may occur
if safety and operational
information is not understood and followed. DO
NOT risk your safety by
not reading!
USE this and other machinery with caution
-8-
and respect. Always consider safety first,
as it applies to your individual working
conditions. No list of safety guidelines can
be complete—every shop environment is
different. Failure to follow guidelines could
result in serious personal injury, damage
to equipment or poor work results.
Page 12
Model W1767 (For Machines Mfd. Since 08/15)
This machine must be connected to the correct size and
type of power supply circuit, or fire or electrical damage
may occur. Read through this section to determine if an
adequate power supply circuit is available. If a correct
circuit is not available, a qualified electrician MUST install
one before you can connect the machine to power.
A power supply circuit includes all electrical equipment
between the breaker box or fuse panel in the building
and the machine. The power supply circuit used for
this machine must be sized to safely handle the fullload current drawn from the machine for an extended
period of time. (If this machine is connected to a circuit
protected by fuses, use a time delay fuse marked D.)
This machine is prewired to operate on a 220V power
supply circuit that has a verified ground and meets the
following requirements:
The full-load current rating is the amperage a machine
draws at 100% of the rated output power. On machines
with multiple motors, this is the amperage drawn by the
largest motor or sum of all motors and electrical devices
that might operate at one time during normal operations.
or machine damage. To reduce this risk,
a dedicated circuit—
where only one machine will be running
multiple machines will be running at the
ELECTRICAL
Circuit Requirements
The machine must be properly set up
before it is safe to operate. DO NOT
connect this machine to the power
source until instructed to do so later in
this manual.
ELECTRICAL
Full-Load Current Rating
Full-Load Current Rating at 220V ............. 4.2A/2.5A
Circuit Requirements
Circuit Type .................... 220V, 60 Hz, Single-Phase
Circuit Size .................................................. 15A
Plug/Receptacle ................................... NEMA 6-15
Incorrectly wiring or grounding this
machine can cause electrocution, fire,
only an electrician or qualified service
personnel should do any required
electrical work on this machine.
NOTICE
The circuit requirements listed in this
manual apply to
at a time. If this machine will be
connected to a shared circuit where
same time, consult with an electrician
to ensure that the circuit is properly
sized for safe operation.
-9-
Page 13
Grounding Requirements
This machine MUST be grounded. In the event of certain
types of
a path of least resistance for electric current
order
Improper connection of the equipment-grounding
will
increase
insulation
grounding
cord or plug is necessary, do not connect the equipmentgrounding
Check with a qualified electrician or service personnel
if
or if
properly grounded.
plug is damaged or worn, disconnect it from power, and
immediately replace it with a new one.
This machine is equipped with a power cord that has an
equipment-grounding
The plug
receptacle
(
accordance with local codes and ordinances.
We do not recommend using an extension cord with
Any extension cord used with this machine must contain a
plug and receptacle, and
meet the following requirements:
the available receptacle or the machine
Model W1767 (For Machines Mfd. Since 08/15)
malfunctions or breakdowns, grounding provides
to reduce the risk of electric shock.
the risk of electric shock. The wire with green
(with/without yellow stripes) is the equipment-
wire. If repair or replacement of the power
wire to a live (current carrying) terminal.
you do not understand these grounding requirements,
ELECTRICAL
you are in doubt about whether the tool is
If you ever notice that a cord or
For 220V Connection
wire and NE M A 6 -15 grounding plug.
must only be inserted into a matching
see Figure) that is properly installed and grounded in
to travel—in
wire
The machine must be properly set up
before it is safe to operate. DO NOT
connect this machine to the power
source until instructed to do later in
this manual.
220V
Current Carrying Prongs
6-15 PLUG
Figure 2. NEMA 6-15 plug & receptacle.
GROUNDED
6-15 RECEPTACLE
Grounding Prong
Extension Cords
this machine. Extension cords cause voltage drop, which
may damage electrical components and shorten motor
life. Voltage drop increases with longer extension cords
and smaller gauge sizes (higher gauge numbers indicate
smaller sizes).
ground wire
Minimum Gauge Size at 220V ...................... 16 AWG
Maximum Length (Shorter is Better) ................50 ft.
, match the required
No adapter should be used with the
required plug. If the plug does not fit
must be reconnected to a different
type of circuit, the reconnection must
be made by an electrician or qualified
service personnel and it must comply
with all local codes and ordinances.
-10-
Page 14
Model W1767 (For Machines Mfd. Since 08/15)
SETUP
Unpacking
This machine has been carefully packaged for safe
transportation. If you notice the machine has been
damaged during shipping, please contact your authorized
Shop Fox dealer immediately.
Inventory
The following is a description of the main components
shipped with the Model W1767. Lay the components out to
inventory them.
Note: If you can't find an item on this list, check the
mounting location on the machine or examine the
packaging materials carefully. Occasionally we pre-install
certain components for safer shipping.
Keep machine disconnected from
power until instructed otherwise.
A
SETUP
Box Inventory (Figures 3 & 4) Qty
A. Power Feeder Assembly ..................................1
B. Lubricator ...................................................1
C. Base and Column Assembly ..............................1
D. Elbow Joint Assembly .....................................1
E. Base Bolt Pattern Template ..............................1
F. Handwheel Handle ........................................1
G. Horizontal Column Assembly .............................1
H. Hex Bolts M12-1.75 x 50 (Not Shown) ..................4
I. Lock Washers 12mm (Not Shown) .......................4
B
Figure 3. Feeder inventory.
C
D
E
F
G
-11-
Figure 4. Column and joint inventory.
Page 15
To prevent
machine, the factory has coated t
of your machine
compound
I
be difficult to
coating is as easy as possible, please gather the correct
cleaner, lubricant, and tools listed below:
• Cleaner/degreaser
and grease
• Safety glasses & disposable gloves
•
• Disposable Rags
To
1.
2.
3
4
5
6
immediately coat with a quality metal protectant.
Cleaning Machine
corrosion during shipment and storage of your
with a heavy-duty rust prevention
.
f you are unprepared or impatient, this compound can
remove. To ensure that the removal of this
designed to remove storage wax
Solvent brush or paint brush
remove rust preventative coating, do these steps:
DISCONNECT MACHINE FROM POWER!
Model W1767 (For Machines Mfd. Since 08/15)
he bare metal surfaces
Gasoline and petroleum
products have low flash
points and can explode
or cause fire if used to
clean machinery. Avoid
using these products
to clean machinery.
Many cleaning solvents
are toxic if inhaled.
Minimize your risk
by only using these
products in a well
ventilated area.
SETUP
Put on safety glasses and disposable gloves.
. Coat the rust preventative with a liberal amount of
cleaner/degreaser, then let it soak for 5–10 minutes.
. Wipe off surfaces. If your cleaner/degreaser is
effective, the coating will wipe off easily.
Tip: An easier way to clean off thick coats of rust
preventative from flat surfaces is to use a PLASTIC
paint scraper to scrape off the majority of the
coating before wiping it off with your rag. (Do
not use a metal scraper or you may scratch your
machine.)
. Repeat cleaning steps as necessary until all of the
compound is removed.
. To prevent rust on freshly cleaned surfaces,
In a pinch, automotive degreasers,
mineral spirits or WD•40 can be used
to remove rust preventative coating.
Before using these products, though,
test them on an inconspicuous area of
your paint to make sure they will not
damage it.
-12-
Page 16
Model W1767 (For Machines Mfd. Since 08/15)
Assembly
To correctly position this power feeder on your table top,
first gather the stand parts shown in Figure 5 and
assemble the power feeder stand (refer to the parts
diagram for any intricate details).
Next, connect the stand to the power feeder as shown
in Figure 6. With your power feeder unit completely
assembled, it will be easier for you to determine where
on the table top to drill your base mounting holes, so
you can take advantage of the full range of power feeder
swing and adjustments. Refer to Base Mounting on Page
14.
You MUST assemble all guards, fences, and holddowns before starting your machine or power
feeder. Failure to heed this warning could result in
serious personal injury.
Figure 5. Item layout.
SETUP
Figure 6. Assembled power feeder.
-13-
Page 17
Base Mounting
Continued on next page
Model W1767 (For Machines Mfd. Since 08/15)
Assemble the power feeder before you mount the
base to determine where on the table top to drill
your base mounting holes, so you can maximize
power feeder swing and adjustment options.
There are two mounting options available,
Through Bolt Mounting and Direct Mounting
options discussed on Page 15. Choose an option
that suits your requirements.
Your final goal is to be able to use the handwheels
and lock levers to position the power feeder
wheels so they are parallel with the table
surface, and
workpiece.
Shaper
SETUP
1
⁄8" lower than the thickness of your
Jointer
Fence Fence
Also, you must be able to adjust the power
feeder so it points towards the machine fence
slightly (see Figure 7). In other words, the
tracking of the power feeder must be toed-in
approximately 1° to 1.5° degrees toward the
machine fence, so the power feeder wheels push
the workpiece against the fence slightly during
cutting operations.
If cutting long or large stock that is difficult to
feed properly, use a featherboard before the
powerfeeder (on the infeed side) to maintain
even pressure and control of the workpiece
against the fence.
Table Saw
Fence
4th-Roller
Models
Blade
Optional
Featherboard
Cutter
Feed
Feed
Cutterhead
Figure 7. Typical power feed mounting on a shaper, jointer, and tablesaw.
Feed
-14-
Page 18
Model W1767 (For Machines Mfd. Since 08/15)
Through-Bolt Mounting
We recommend that you mount your new power feeder
to the machine table using the included M12-1.75 x 50
hex bolts and lock washers, plus additional flat washers
and locking hex nuts for a through-bolt setup (see Figure
8). This option will give the most rigidity and clamping
strength to prevent the feeder base from twisting out of
alignment during use. However, if any under-table support
webs interfere with washer or nut locations under the
table, you will have to use an optional clamping kit, or
drill and thread holes directly into the table as described
in the Direct Mounting paragraph below.
Direct Mounting
Use the included mounting template to drill and tap your
table, so the power feeder base can be directly mounted
to the table surface (see Figure 9) using the included
M12-1.75 x 50 hex bolts and lock washers, plus additional
flat washers. If the table is thinner than than
where the threaded holes would be drilled and tapped,
or if support webbing is in the way, the threads may strip
or loosen as the power feeder is used. Thread locking
compound will not cure this problem. Revert to the
Through-Bolt Mounting option. In any case, make sure to
use a medium-grade liquid thread locking compound on all
threads.
3
⁄8" thick
Feeder
Base
Machine Table
Table
Support
Webbing
Bolt
Flat Washer
Flat Washer
Lock Washer
Locking Hex Nut
Figure 8. Through-bolt mounting.
Feeder
Base
Machine Table
Bolt
Lock Washer
Flat Washer
SETUP
Table
Support
Webbing
Apply A Medium
Grade Thread
Locking Compound
To The Threads
Figure 9. Direct mounting.
-15-
Page 19
Test Run
Once power feeder assembly is complete and mounted on
the table, you must test run your power feeder to make
sure it runs properly. Your power feeder motor has two
feed speeds and two feed directions that are controlled at
the switch (see Figure 10).
If, during the test run, you cannot easily locate the source
of an unusual noise or vibration, stop using the power
feeder immediately, then review the Troubleshooting
table on Page 23.
If you still cannot remedy a problem, contact our
Technical Support at (360) 734-3482 for assistance.
To test run the power feeder, do these steps:
1. Make sure you understand the safety instructions
at the beginning of the manual, and verify that the
power feeder is adjusted and is setup properly.
Model W1767 (For Machines Mfd. Since 08/15)
Projectiles thrown from the machine
could cause serious eye injury. Wear
safety glasses to reduce the risk of
injury.
2. Make sure that the power feeder gearbox oil level is
SETUP
full. The oil level should be 1" below the oil fill port.
Note: See Figure 14 on Page 21 for oil fill port
location.
3. Ensure that all tools and objects used during set up
are cleared away from the machine.
4. Adjust and lock the power feeder so the wheels are
held approximately one inch above the table and
nothing will interfere with wheel rotation.
5. Connect the power feeder to the power supply and
use the feed direction and speed switch (see Figure
10) to test operation in both feed directions.
— Listen and watch for abnormal noises or
vibrations. The power feeder should run smoothly.
— Correct for any unusual noises or vibrations before
operating the power feeder any further. Always
disconnect the power feeder from power when
investigating or correcting potential problems.
Loose hair and clothing could get
caught in machinery and cause serious
personal injury. Keep loose clothing
rolled up and long hair tied up and
away from machinery.
6. Turn the feed direction switch to OFF.
Figure 10. Feed direction and speed
switch.
-16-
Page 20
Model W1767 (For Machines Mfd. Since 08/15)
OPERATIONS
General
This machine will perform many types of operations
that are beyond the scope of this manual. Many of these
operations can be dangerous or deadly if performed
incorrectly.
The instructions in this section are written with the
understanding that the operator has the necessary
knowledge and skills to operate this machine. If at
any time you experience difficulties performing any
operation, stop using the machine!
If you are an inexperienced operator, we strongly
recommend that you read books, trade articles, or seek
training from an experienced power feeder operator
before performing any unfamiliar operations. Above all,
your safety should come first!
READ and understand this entire
instruction manual before using this
machine. Serious personal injury may
occur if safety and operational information is not understood and followed.
DO NOT risk your safety by not reading!
Basic Use and Care
Power feeders reduce kickback hazards and improve
cutting results by feeding in a consistent and stable
manner. Remember, do not to stand in the path of
potential kickback. When not in use, support the power
feeder with a wooden block so the rubber wheels are
raised above the table and do not compress from the
weight of the power feeder.
The lock levers and handcranks allow you to adjust the
power feeder tracking and height to accommodate many
workpiece sizes. Before loosening any lock lever, always
support the power feeder with a block of wood, so the
power feeder does not drop and cause damage.
Adjust the power feeder so it is toed-in approximately
1° to 1.5° degrees towards the machine fence. This
adjustment will ensure the power feeder wheels slightly
push the workpiece against the fence during cutting
operations (see Figure 7 on Page 14). A featherboard
may be used on the infeed side to help feed long or large
stock.
OPERATIONS
DO NOT investigate problems or adjust
the machine while it is running. Wait
until the machine is turned OFF,
unplugged and all working parts
have come to a complete stop before
proceeding!
Next, adjust the power feeder so the rubber wheels are
parallel with the table surface, and are
the thickness of your workpiece. This adjustment ensures
that the workpiece will not slip or hang in the middle of
a cut. Always double check that the power feeder wheels
are slightly lower than the workpiece before you begin
feeding operations. Otherwise, the workpiece may slip
and kickback.
1
⁄8" lower than
-17-
Always wear safety glasses when operating this machine. Failure to comply
may result in serious personal injury.
Page 21
Changing Feed Speed
Your power feeder has the option to feed a workpiece
at 13, 26, 33, and 66 feet per minute. These rates are
achieved by changing the combination of change gears,
shown in Figure 11, and turning the motor switch to high
or low range operation, shown in Figure 12.
To change the power feeder feed rate, do these steps:
1. DISCONNECT THE MACHINE FROM POWER!
Model W1767 (For Machines Mfd. Since 08/15)
2. Turn the dial to the OFF ("0") position.
3. Refer to the feed rate list below to find the gear
combination required for your chosen feed rate.
Low Range Speed:
— A, 25 Tooth + B, 40 Tooth = 13 Ft Per Min.
Low Range Speed:
— A, 40 Tooth + B, 25 Tooth = 26 Ft Per Min.
High Range Speed:
— A, 25 Tooth + B, 40 Tooth = 33 Ft Per Min.
High Range Speed:
— A, 40 Tooth + B, 25 Tooth = 66 Ft Per Min.
Motor OFF.
Low Range Speed W/Optional D3886 Gear Kit:
OPERATIONS
— A, 21 Tooth + B, 44 Tooth = 9.4 Ft Per Min.
Low Range Speed W/Optional D3886 Gear Kit:
— A, 44 Tooth + B, 21 Tooth = 18.8 Ft Per Min.
MAKE SURE that your machine is
unplugged during all maintenance
procedures! If this warning is ignored,
serious personal injury may occur.
Change Gear
Position A
Figure 11. Change gear locations.
Change Gear
Position B
High Range Speed W/Optional D3886 Gear Kit:
— A, 21 Tooth + B, 44 Tooth = 41.4 Ft Per Min.
High Range Speed W/Optional D3886 Gear Kit:
— A, 44 Tooth + B, 21 Tooth = 82.7 Ft Per Min.
4. Remove the chain cover and the two hex nuts
securing the position A & B change gears to the
shafts.
5. Swap the required change gears so the gear hubs
face the power feeder (positions A & B, Figure 11).
6. Re-install the hex nuts and the chain cover.
7. Re-connect the power feeder and move the feed
direction and speed switch to High or Low range.
-18-
Figure 12. Feed direction and speed
switch.
Page 22
Model W1767 (For Machines Mfd. Since 08/15)
Power Feeder Accessories
The following power feeder accessories may be available through your local Woodstock International Inc.
Dealer. If you do not have a dealer in your area, these products are also available through online dealers.
Please call or e-mail Woodstock International Inc. Customer Service to get a current listing of dealers at:
1-800-840-8420 or at [email protected].
The Model D3886 Shop Fox Extra Gear Kit adds versatility by
giving your power feeder four extra feed speeds: of 9.4, 18.8, 41.4,
and 82.2 ft/min. This gear set contains one 44-tooth gear, and one
21-tooth gear.
The flange and tire system can save you money over the long haul by
replacing the rollers with one of these roller flange and tire systems.
Once you buy the complete flange and tire system, you simply replace
the inexpensive rubber or polyurethane tires when they wear out.
Polyurethane tires are even more economical since they last up to six
times longer than rubber.
The Model D3720 Flange Wheel with Rubber Roller
The Model D3721 Flange Wheel with Poly Roller
The Model D3722 Replacement Rubber Roller for D3720 (Not Shown)
The Model D3873 Extra Roller adds insurance against downtime
should a workpiece damage a wheel, or after long use the wheel tire
wears out. These wheels can be replace in a few minutes.
D3886
D3720
D3721
OPERATIONS
D3873
The Model D3122 Push Stick keeps hands a safe distance from
blades and cutters while still maintaining control of the workpiece
against machine fences. A true necessity when running narrow stock.
Durable handle is designed for maximum control. Measures 13
overall.
-19-
1
⁄2"
D3122
Page 23
Model W1767 (For Machines Mfd. Since 08/15)
The Model D3096 Shop Fox Featherboard helps reduce the risk
of kick-back and achieve consistent results. Designed to lock into
3
standard
⁄8" x 3⁄4" miter gauge slots, this Featherboard is adjustable
for various stock widths and miter slot locations. No drilling or bulky
clamp arrangements!
The Model D2018 60-Pc. Tap & Die Set includes both coarse and
fine thread tap and dies. Tap and dies are numbered from #4 - 40 to
#12 - 24 and fractional taps and dies from 1/4" - 28 to 1/2" - 20 and
1/8" - 27 NPT. Set includes thread gauge, tap handle, die handle and
small tap chuck, all in a nice molded case. Also includes metric taps
and dies from M3 x .5 to M12 x 1.75. Made of high carbon steel.
The Model D2675 Shop Fox Metal Frame Safety Glasses
features a metal band across the top that is not only stylish, but
adds strength. This band is linked to the metal ear pieces through a
tough hinge. These glasses have a wide field of view and side shields
for added protection. Exceeds ANSI Z87.1 - 1989 standards for impact
resistance.
D3096
D2018
D2675
OPERATIONS
-20-
Page 24
Model W1767 (For Machines Mfd. Since 08/15)
MAINTENANCE
General
Regular periodic maintenance on your machine will
ensure its optimum performance. Make a habit of
inspecting your machine each time you use it.
Check for the following conditions and repair or
replace when necessary:
• Loose mounting bolts and damaged wheel rubber.
• Worn or damaged, switch, cord, and plug.
• Any other condition that could hamper the safe
operation of this power feeder.
Cleaning
• Frequently blow-off sawdust with compressed air.
This is especially important for the internal working
parts and motor. Dust build-up around the motor is a
sure way to decrease its life span.
• If the wheels become loaded up with pitch, oil, or
other residues, wipe them clean using a clean rag
and a mild solvent. Avoid touching the plastic or
paint with mineral spirits or you may damage the
surfaces.
MAKE SURE that your machine is
unplugged during all maintenance
procedures! If this warning is ignored,
serious personal injury may occur.
Grease
Fitting
Lubrication
• To prevent surface rust and binding, periodically
clean and oil all lock lever and lead screw threads
with a light machine oil.
• After the first month or 200 hours of use, change the
gearbox oil with 5.1 fluid ounces of an automotive
grade 80-90W gear oil. For the remaining life of the
power feeder, change the oil every 6 months or 1000
hours of use. Note: To drain the unit, remove the
fill plug labeled "OIL" (see Figure 14) and invert the
power feeder.
• Every 200 hours of use, or after the first month,
wipe clean and lubricate the wheel grease fittings
(see Figure 13) with one pump from a grease gun
filled with automotive grade GL-2 grease.
• To prevent rust and binding, paint the sprockets,
chain, and change gears (see Figure 14) with a light
film of an automotive grade GL-2 grade grease.
Figure 13. Wheel lubrication.
Oil Fill
Plug
Sprocket
Figure 14. Sprockets, chain, and change
Change
Gears
gears.
Chain
MAINTENANCE
-21-
Page 25
SERVICE
General
This section covers the most common service adjustments
or procedures that may need to be made during the life
of your machine.
If you require additional machine service not included
in this section, please contact Woodstock International
Technical Support at (360) 734-3482 or send e-mail to:
Wheel Replacement
To replace a worn out or damaged wheel, do these
steps:
Model W1767 (For Machines Mfd. Since 08/15)
MAKE SURE that your machine is
unplugged during all service procedures!
If this warning is ignored, serious
personal injury may occur.
1. DISCONNECT THE MACHINE FROM POWER!
2. Using a 5mm hex wrench, remove the wheel
retaining cap screws (see Figure 15).
3. Swap the old wheel with the new.
4. Re-install the four cap screws, and tighten in an
alternating pattern until the wheel is tight.
Cap
Screw
Figure 15. Wheel replacement.
SERVICE
-22-
Page 26
Model W1767 (For Machines Mfd. Since 08/15)
Troubleshooting
This section covers the most common problems and corrections with this type of
machine. WARNING! DO NOT make any adjustments until power is disconnected and
moving parts have come to a complete stop!
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Motor will not start. 1. Low voltage.
2. Open circuit in motor or loose
connections.
3. Faulty start capacitor.
4. Faulty motor switch.
Fuses or circuit breakers
trip open.
Motor overheats. 1. Motor overloaded.
Workpiece jams when
feeding under rollers.
Workpiece slips while
passing beneath rollers.
Workpiece is burnt. 1. Wrong feed speed. 1. Adjust feed speed.
Rough finish or chipped
grain on workpiece.
Fuzzy grain occurs when
planing or moulding.
Workpiece hangs and does
not enter the machine.
1. Short circuit in line cord or plug.
2. Short circuit in motor or loose
connections.
3. Incorrect fuses or circuit breakers
in power supply.
2. Air circulation through the motor
restricted.
1. Rollers set too low.
2. Feeder at wrong angle.
1. Rollers positioned too high, no
traction.
2. Feeding too fast.
3. Rollers are dirty or oily.
4. Worn roller(s).
1. Feed speed too fast.
2. Dull cutter or blade.
3. Power feeder angle is not toed
in to keep workpiece against the
fence.
1. Lumber has high moisture content.
2. Dull knives.
1. Power feeder roller height is set
incorrectly.
1. Check power supply for proper voltage.
2. Inspect all lead connections on motor and magnetic
switch for loose or open connections.
3. Replace start capacitor.
4. Replace switch.
1. Inspect cord or plug for damaged insulation and
shorted wires and replace extension cord.
2. Inspect all connections on motor for loose or
shorted terminals or worn insulation.
3. Install correct fuses or circuit breakers.
1. Reduce power feeder feed rate.
2. Clean out motor fan cover to provide normal air
circulation.
1. Raise feeder.
2. Adjust angle.
1. Lower feeder.
2. Slow feed speed.
3. Clean roller surface with a mild solvent that leaves
no residue.
4. Replace roller(s).
1. Slow speed.
2. Replace with sharp cutter or blade.
3. Adjust power feeder so it is toed-in 1° to 1.5°.
1. If moisture content is higher than 20%, sticker and
allow to dry.
2. Sharpen or replace knives.
1. Lower the power feeder roller
height of the workpiece.
1
"
lower than the
⁄8
-23-
SERVICE
Page 27
Model W1767 (For Machines Mfd. Since 08/15)
MOTOR WIRING. The motor wiring shown in these
shocked, wait at least this long before working
SHOCK HAZARD. Working on wiring that is
QUALIFIED ELECTRICIAN
WIRE CONNECTIONS.
WIRE/COMPONENT DAMAGE
Electrical Safety Instructions
These pages are current at the time of printing. However, in the spirit of improvement, we may
make changes to the electrical systems of future machines. Study this diagram carefully. If you notice
differences between your machine and these wiring diagrams, call Woodstock International Technical
Support at (360) 734-3482.
connected to a power source is extremely
dangerous. Touching electrified parts will
result in personal injury including but not
limited to severe burns, electrocution,
or death. Disconnect the power from
the machine before servicing electrical
components!
. Due to the inherent
hazards of electricity, only a qualified
electrician should perform wiring tasks on this
machine. If you are not a qualified electrician,
get help from one before attempting any kind
of wiring job.
All connections must be
tight to prevent wires from loosening during
machine operation. Double-check all wires
disconnected or connected during any wiring
task to ensure tight connections.
. Damaged wires
or components increase the risk of serious
personal injury, fire, or machine damage.
If you notice that any wires or components
are damaged while performing a wiring task,
replace those wires or components before
completing the task.
diagrams is current at the time of printing,
but it may not match your machine. Always
use the wiring diagram inside the motor
junction box.
MODIFICATIONS. Using aftermarket parts or
modifying the wiring beyond what is shown
in the diagram may lead to unpredictable
results, including serious injury or fire.
CAPACITORS/INVERTERS. Some capacitors and
power inverters store an electrical charge for
up to five minutes after being disconnected
from the power source. To avoid being
on these components.
ELECTRICAL REQUIREMENTS. You MUST follow
the electrical requirements at the beginning
of this manual when connecting your machine
to a power source.
EXPERIENCING DIFFICULTIES. If you are
experiencing difficulties understanding the
information included in this section, contact
our Technical Support at (360) 734-3482.
The photos and diagrams
included in this section are
best viewed in color. You
can view these pages in
color at www.shopfox.biz.
SERVICE
BLACK
WHITE
GREEN
RED
WIRING DIAGRAM COLOR KEY
BLUE
BROWN
GRAY
ORANGE
-24-
YELLOW
YELLOW
GREEN
PURPLE
PINK
LIGHT
BLUE
BLUE
WHITE
TURQUOISE
Page 28
Model W1767 (For Machines Mfd. Since 08/15)
Wiring Diagram
V
Two Speed
Motor
Direction
Switch
Z
18 17
22
Side A Side B
3 4
7 8
U
11 12
Y
15 16
19 20
23 24
2 1
R
S
6 5
W
10 9
14 13
X
T
220V
Two Speed
Motor
35MFD
400VAC
Capacitor
1
4
6
Ground
3
21
5
2
Hot
Hot
6-15 Plug
(As Recommended)
G
Read
Page 24
STOP
Before
Wiring
SERVICE
Figure 16. Motor switch.
Figure 17. Motor switch and capacitor.
-25-
Page 29
63
63
5
5
10
10
19
19
70
70
87
87
14
14
17
17
9
9
89
89
Model W1767 (For Machines Mfd. Since 08/15)
PARTS
Main Breakdown
87
87
19
10
10
8
8
6
6
88
88
29
29
18
18
25
25
26
26
36
36
19
79
79
75
75
20
20
24
24
87
87
11
11
4
4
70-1
70-1
70-3
70-3
89
89
10
10
16
16
24
24
25
25
70-2
70-2
70-5
70-5
12
12
16
16
19
19
13
13
9
9
12
12
11
11
11
11
13
13
3
3
70-6
70-6
89
89
25
25
7
7
2
2
26
26
90
90
70-4
70-4
16
16
12
12
88
88
88
88
91
91
13
13
26
24
24
7
7
17
17
28
28
77
77
68
68
17
17
58
58
8
8
44
44
1
1
31
31
57
57
51
51
6
6
30
30
32
32
39
39
18
18
52
52
37
37
18
18
38
38
36
36
64
64
50
50
22
22
53
53
20
20
23
23
62
62
56
56
81
81
27
27
55
55
PARTS
-26-
Page 30
Model W1767 (For Machines Mfd. Since 08/15)
37 X1767037 CHAIN (62S)
Main Parts List
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 X1767001 BALL BEARING 6203 OPEN 38 X1767038 DOUBLE SPROCKET
2 X1767002 GREASE FITTING 39 X1767039 CHAIN (40S)
3 X1767003 SPROCKET CASE 44 X1767044 WORM GEAR
4 X1767004 TORSION SPRING 3.8 X 102 50 X1767050 O-RING 101.19MM X 3.53MM
5 X1767005 CASE COVER 51 X1767051 WORM GEAR BOX COVER
6 X1767006 GREASE NIPPLE 52 X1767052 OIL SEAL
7 X1767007 SPROCKET CASE 53 X1767053 CAP SCREW M5-.8 X 16
8 X1767008 TORSION SPRING 3.8 X 102 55 X1767055 FLAT WASHER 1/2
9 X1767009 CASE COVER 56 X1767056 HEX NUT M12-1.75
10 X1767010 ROLLER SUPPORT 57 X1767057 WORM GEAR SHAFT
11 X1767011 SPROCKET 58 X1767058 WORM GEAR KEY
12 X1767012 LOCK WASHER 6MM 62 X1767062 GEAR 25T
13 X1767013 CAP SCREW M6-1 X 16 63 X1767063 CAP SCREW M8-1.25 X 40
14 X1767014 LOCK WASHER 8MM 64 X1767064 GEAR 40T
16 X1767016 CHAIN (26S) 68 X1767068 LUBRICATOR
17 X1767017 TUBE 70 X1767070 MOTOR 220V 2SPD 1PH
18 X1767018 EXT RETAINING RING 24 70-1 X1767070-1 SWITCH W/ELECTRICAL BOX
19 X1767019 SPROCKET SHAFT 70-2 X1767070-2 BOX COVER
20 X1767020 EXT RETAINING RING 13MM 70-3 X1767070-3 FAN COVER
22 X1767022 FLAT WASHER 1/2 70-4 X1767070-4 MOTOR FAN
23 X1767023 HEX NUT M12-1.75 70-5 X1767070-5 CAPACITOR 35MFD 250VAC
24 X1767024 GREASE NIPPLE 70-6 X1767070-6 SEALING RING
25 X1767025 ROLLER SPINDLE 75 X1767075 O-RING 27.5 X 2.0 S28
26 X1767026 SPROCKET CASE HEX BOLT M12-1.75 77 X1767077 CAP
27 X1767027 KNOB 79 X1767079 CAP SCREW M5-.8 X 10
28 X1767028 OIL CAP 81 X1767081 BACK COVER
29 X1767029 O-RING 14.8 X 2.4 P15 87 X1767087 ROLLER
30 X1767030 CASTING 88 X1767088 LOCK WASHER 12MM
31 X1767031 BUSHING 89 X1767089 EXT RETAINING RING 20MM
32 X1767032 SET SCREW M6-1 X 10 90 X1767090 HEX BOLT M8-1.25 X 20
36 X1767036 SPROCKET 91 X1767091 LOCK WASHER 8MM
PARTS
-27-
Page 31
Model W1767 (For Machines Mfd. Since 08/15)
Stand Breakdown
104
103
110V2
103
216
121V2
215
106V3
162
160
217
218
154
102V2
160
100
151
155
114
118
160
122
102V2
159
119
120
131
155
126
103
104
161
134
163
104
157
103
128
141
124
141
140
125
151
129
104
REF PART # DESCRIPTION REF PART # DESCRIPTION
100 X1767100 COLUMN BASE 131 X1767131 HORIZONTAL TUBE CONE
102V2 X1767102V2 HEX BOLT M12-1.75 X 75 134 X1767134 ROLL PIN 6 X 22
103 X1767103 FLAT WASHER 12MM 140 X1767140 SWIVEL CLAMP CONE
104 X1767104 T-HANDLE 141 X1767141 SHOULDER LOCK STUD
106V3 X1767106V3 VERTICAL COLUMN W/GUIDE V3.08.15 151 X1767151 HANDLE
110V2 X1767110V2 HORIZONTAL TUBE W/RACK V2.02.97 154 X1767154 CRANK ARM
114 X1767114 ELEVATING BRACKET 155 X1767155 ROLL PIN 6 X 40
118 X1767118 VERTICAL LEAD SCREW 157 X1767157 HEX BOLT M10-1.5 X 50
119 X1767119 SET SCREW M8-1.25 X 20 159 X1767159 PINION
120 X1767120 LOCK WASHER 8MM 160 X1767160 LOCK WASHER 12MM
121V2 X1767121V2 COLUMN CAP V2.08.15 161 X1767161 STRAIN RELIEF
122 X1767122 HEX NUT M8-1.25 162 X1767162 HEX BOLT M12-1.75 X 50
124 X1767124 ELBOW 163 X1767163 CRANK HANDWHEEL
125 X1767125 LOCK LEVER 215 X1767215 ANCHOR FINNED M8-1.25
126 X1767126 T-HANDLE 216 X1767216 FLAT WASHER 8MM
128 X1767128 FLAT WASHER 10MM 217 X1767217 CAP SCREW M8-1.25 X 25
129 X1767129 HEX BOLT M8-1.25 X 50 218 X1767218 FLAT WASHER 15MM
PARTS
-28-
Page 32
Model W1767 (For Machines Mfd. Since 08/15)
Labels & Cosmetics
Safety labels warn about machine hazards and how to prevent serious personal injury. The owner
of this machine MUST maintain the original location and readability of all labels on this machine.
If any label is removed or becomes unreadable, REPLACE that label before allowing machine to be
operated again. Contact us at (360) 734-3482 or www.shopfoxtools.com to order new labels.
200V2
213
206
201
202
211
214
212
205
REF PART # DESCRIPTION REF PART # DESCRIPTION
200V2 X1767200V2 MACHINE ID LABEL CSA V2.10.12 211 X1767211 DAMPNESS WARNING LABEL
201 X1767201 ENTANGLEMENT LABEL 212 X1767212 DISCONNECT POWER LABEL
202 X1767202 READ MANUAL LABEL 213 X1767213 LUBRICATION NOTICE LABEL
205 X1767205 SHOP FOX LOGO LABEL 214 X1767214 SHOP FOX WHITE TOUCH-UP PAINT
206 X1767206 ELECTRICITY WARNING LABEL
PARTS
-29-
Page 33
Notes
Model W1767 (For Machines Mfd. Since 08/15)
PARTS
-30-
Page 34
Model W1767 (For Machines Mfg. Since 5/07)
Page 35
FOLD ALONG DOTTED LINE
FOLD ALONG DOTTED LINE
Place
Stamp
Here
Woodstock international inc.
p.o. box 2309
bellingham, Wa 98227-2309
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Page 36
WARRANTY
WARRANTY
Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship
and materials for a period of two years from the date of original purchase by the original owner.
This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or
accidents, lack of maintenance, or reimbursement of third party expenses incurred.
Woodstock International, Inc. will repair, replace, or arrange for a dealer refund at its expense and
at its option, the Shop Fox machine or machine part, which in proper and intended use has proven to
be defective, provided that the original owner returns the product prepaid to an authorized warranty
or repair facility as designated by our Bellingham, Washington office with proof of their purchase of
the product within two years, and provides Woodstock International, Inc. reasonable opportunity to
verify the alleged defect through inspection. If it is determined there is no defect, or that the defect
resulted from causes not within the scope of Woodstock International Inc.'s warranty, then the original
owner must bear the cost of storing and returning the product.
This is Woodstock International, Inc.’s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited
to the duration of this written warranty. We do not warrant that Shop Fox machinery complies with
the provisions of any law, acts or electrical codes. We do not reimburse for third party repairs. In no
event shall Woodstock International, Inc.’s liability under this limited warranty exceed the purchase
price paid for the product, and any legal actions brought against Woodstock International, Inc. shall be
tried in the State of Washington, County of Whatcom. We shall in no event be liable for death, injuries
to persons or property or for incidental, contingent, special or consequential damages arising from the
use of our products.
Every effort has been made to ensure that all Shop Fox machinery meets high quality and durability
Page 37
Loading...