Shop fox M1023 User Manual

MODEL M1023
QUICK CHANGE
COLLET ATTACHMENT
INSTRUCTION MANUAL
Phone: 1-360-734-3482 • On-Line Technical Support: tech-support@shopfox.biz
COPYRIGHT © JANUARY, 2005 BY WOODSTOCK INTERNATIONAL, INC.
WARNI NG: NO PO RTION OF THI S MANUA L MAY B E REPRO DUCED IN ANY S HAPE OR F ORM WITHOU T
#6727 BL
THE WRI TTEN AP PROVAL OF WO ODSTO CK INTERNATIONA L, INC.
M1023 Quick Change Collet Attachment
INVENTORY
The following is a description of the main components shipped with the components out to inventory them.
Box Contents (Figure 1) QTY
A. Collet Attachment Assembly ..............................1
B. Collet Adapter ...............................................1
C. Handle ........................................................1
D. Lever ..........................................................1
If any parts appear to be missing, examine the packag ing carefully to be sure those parts are not among the packing materials. If any parts are missing, find the part number in the back of this manual and contact Woodstock International, Inc. at (360) 734-3482 or at tech-support@shopfox.biz
SHOP FOX
®
Model M1023. Lay the
-
A
B
C D
Figure 1. Model M1023 Inventory.
NOTICE
When ordering replacement parts, refer to the parts list and diagram in the back of the manual.
-3-
ASSEMBLY
The Model M1023 Quick Change Collet Attachment allows you to quickly change workpieces on your Model M1020 Gear Head Lathe. The positive-locking handle clamps standard 5-C collets safely and securely for precision turning.
Disconnect power to your lathe before beginning installation of the Model M1023 Quick Change Collet Attachment.
M1023 Quick Change Collet Attachment
Preparation
To begin assembly, follow these initial safety instruc­tions.
1. Disconnect the lathe from the power source!
2. Remove the chuck or any other device that is
mounted to the spindle. (Refer to your Model M1020 Gear Head Lathe owner’s manual.)
3. Make sure the 5-C Collet/Morse Taper Adapter and
the spindle opening are clean and free of oil. Use a soft cloth or rag to wipe up any contaminants.
Pivot Stud
To install the pivot connector onto the headstock, do these steps:
1. Open the lathe cover as shown in Figure 2.
2. Unscrew the M12-1.75 x 40 hex bolt and two flat
12mm washers from the end of the pivot connector on the collet attachment assembly.
Figure 2. Opening cover.
Hole
Figure 3. Installing hex bolt on headstock.
3. Unscrew the cap screw in the pivot connector to
remove the pivot stud from the collet attachment assembly.
4. Insert the hex bolt through the bottom of the hole
shown in bolt and thread the pivot stud onto the bolt, as shown in Figure 4.
Figure 3. Slide both washers over the hex
-4-
Pivot
Stud
Figure 4. Threading pivot stud onto the
hex bolt.
M1023 Quick Change Collet Attachment
5. Align the stud so its flat surfaces are parallel to the
lathe spindle, and tighten the hex bolt and pivot stud.
6. Close the end cover.
Hub Adapter
To install the hub adapter to the outboard spindle, do these steps:
1. Remove the hub adapter from the draw tube assem- bly.
Hub Adapter
2. Thread the hub adapter completely into the outboard end of the spindle and tighten securely (see
5).
Figure
Draw Tube Assembly
The draw tube assembly comes attached to the locking yoke and connecting rod.
To install the draw tube assembly into your lathe, do these steps:
1. Slide the draw tube assembly (Figure 6) all the way
into the outboard spindle until it engages around the hub adapter
2. Thread the handle into the lever.
3. Thread the lever onto the end of the locking yoke
and tighten the locknut.
4. Slide the pivot connector at the end of the connect-
ing rod over the pivot stud, as shown in Insert the M8-1.25 x 45 cap screw through the hole in the pivot connector and pivot stud.
5. Check the handle alignment to make sure it is verti­cal; if it is, go to Step 7. If the handle alignment is not vertical, remove the M8-1.25 x 45 cap screw and adjust the connecting rod until the lever is approxi mately vertical.
.
Figure 7.
Figure 5. Threading hub adapter onto
spindle.
Locking Yoke
Figure 6. Inserting draw tube assembly.
Connecting Rod
-
Draw Tube
Pivot Stud
Pivot Connector
-5-
Figure 7. Pivot connector inserted over
pivot stud.
Loading...
+ 11 hidden pages