Shop fox D4111 User Manual
Model D4111
Heavy-Duty Roller Stand
Instruction Sheet
Phone #: (360) 734-3482 • Online Tech Support: tech-support@shopfox.biz • Web: www.shopfox.biz
Introduction
The Model D4111 Heavy-Duty Roller Stand is vertically
adjustable from 26
handle and the attached elevation gears, as shown in
Figure 1. The stand has a 270 lb. capacity.
Inventory
After removing the contents of the shipping box, lay them
out and refer to the Parts Diagram & List on the back
page to inventory the components.
Assembly
Refer to Figure 1 and the Parts Diagram to aid you during assembly.
Tools Needed Qty
Phillips Screwdriver #2 .........................................1
Hex Wrench 3mm ...............................................1
Wrench or Socket 10mm .......................................1
Wrench or Socket 13mm .......................................1
1
⁄2" to 41" with the use of a crank
Roller
Crank
Handle
Elevation
Gearbox
Lock
Knob
To assemble the roller stand, do these steps:
1. Thread the four foot pads into the base.
2. Secure the bottom vertical support onto the base by
threading the
flat washer through the bottom of the base and into
the support.
3. Insert the top vertical support into the bottom sup-
port with the horizontal slits facing toward the gear
assembly mounting.
4. Position the elevation gearbox onto its mounting
point and make sure the gear teeth mesh with the
slits in the top vertical support, then secure the
gearbox with the four
screws.
5. Align the set screw in the crank handle hub with the
flat of the gear assembly shaft, slide the crank onto
the shaft, then tighten the set screw to secure it in
place.
3
⁄8"-16 x 1" hex bolt, lock washer, and
1
⁄4"-20 x 1⁄2" Phillips head
Adjustable Foot Pad
Figure 1. Model D4111 identification.
6. Thread the two lock knobs into the
holes on the bottom support.
7. Attach the roller bracket to the top
vertical support with the four
1
⁄2" flange bolts.
8. Insert one side of the roller axle into
a roller bracket mounting hole, then
push in on the other end of the springloaded axle until you can insert it into
the remaining mounting hole.
1
⁄4"-20 x
D4111 Heavy-Duty Roller Stand Instructions
REF PART # DESCRIPTION QTY REF PART # DESCRIPTION QTY
101 XD4111101 TOP VERTICAL SUPPORT 1 111 XD4111111 WORM GEAR 1
102 XD4111102 BOTTOM VERTICAL SUPPORT 1 112 XD4111112 GEAR HOUSING 1
103 XD4111103 ROLLER BRACKET 1 113 XD4111113 BUSHING 2
104 XD4111104 ROLLER ASSEMBLY 1 114 XD4111114 BEVEL GEAR 1
105 XD4111105 BASE 1 115 XD4111115 GEAR AXLE 1
106 XD4111106 LOCK KNOB 5/16-18 X 3/4 2 116 XD4111116 CRANK HANDLE 1
107 XPFB03 FLANGE BOLT 1/4-20 X 1/2 4 117 XPLW04 LOCK WASHER 3/8 1
108 XPS04 PHLP HD SCR 1/4-20 X 1/2 4 118 XD4111118 FOOT PAD M6-1 X 20 4
109 XPW02 FLAT WASHER 3/8 1 119 XPSS01M SET SCREW M6-1 X 10 1
110 XPB18 HEX BOLT 3/8-16 X 1 1
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
Parts Diagram & List
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
COPYRIGHT © JUNE, 2010 BY WOODSTOCK INTERNATIONAL, INC.
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
-2-
Printed in Taiwan#13035TS
Loading...