Page 1
76Gears
14, 16, 18, 20, 22, 24, 34T
14, 16, 18, 20, 22, 24, 28T
13, 15, 17, 19, 21, 24, 34T
14, 16, 18, 21, 24, 34T
14, 16, 18, 21, 24, 28T
Tooth combination
RD-TX70
Smartcage
7 / 6
43T
28-34T
11T
20T
RD-TX50
Smartcage
7 / 6
43T
28-34T
11T
20T
RD-TX30
Smartcage
7 / 6
43T
28-34T
11T
20T
Model number
Type
Gears
Total capacity
Rear largest sprocket
Rear smallest sprocket
Front chainwheel tooth difference
SL-RS43-6
SIS 6-gears
SL-RS43-7
SIS 7-gears
Model number
Gears
Technical Service Instructions SI-6KP0A-001
Rear Drive System
General Safety Information
WARNING
• Use neutral detergent to clean the chain. Do not use alkali-based or acid based detergent such as rust cleaners as it may
result in damage and/or failure of the chain.
• Use the reinforced connecting pin only for connecting the narrow type of chain.
• There are two different types of reinforced connecting pins available. Be sure to check the table below before selecting
which pin to use. If connecting pins other than reinforced connecting pins are used, or if a reinforced connecting pin or tool
which is not suitable for the type of chain is used, sufficient connection force may not be obtained, which could cause the
chain to break or fall off.
• If it is necessary to adjust the length of the chain due to a change in the number of sprocket
teeth, make the cut at some other place than the place where the chain has been joined
using a reinforced connecting pin or an end pin. The chain will be damaged if it is cut at a
place where it has been joined with a reinforced connecting pin or an end pin.
• Check that the tension of the chain is correct and that the chain is not damaged. If the
tension is too weak or the chain is damaged, the chain should be replaced. If this is not
done, the chain may break and cause serious injury.
• Check that the wheels are fastened securely before riding the bicycle. If the wheels are loose in any way, they may come
off the bicycle and serious injury may result.
• Obtain and read the service instructions carefully prior to installing the parts.
Loose, worn, or damaged parts may cause injury to the rider. We strongly recommend only using genuine Shimano
replacement parts.
• Obtain and read the service instructions carefully prior to installing the parts.
If adjustments are not carried out correctly, the chain may come off and this may cause you to fall off the bicycle which
could result in serious injury.
• Read these Technical Service Instructions carefully, and keep them in a safe place for later reference.
Note
• The reinforced connecting pins cannot be used with the UG chain, otherwise the connections will not move properly and
noise will occur.
• If gear shifting operations do not feel smooth, wash the derailleur and lubricate all moving parts.
• If the amount of looseness in the links is so great that adjustment is not possible, you should replace the derailleur.
• You should periodically clean the derailleur and lubricate all moving parts (mechanism and pulleys).
• If gear shifting adjustment cannot be carried out, check the degree of parallelism at the rear end of the bicycle. Also check
if the cable is lubricated and if the outer casing is too long or too short.
• If you hear abnormal noise as a result of looseness in a pulley, you should replace the pulley.
• If the wheel becomes stiff and difficult to turn, you should lubricate it with grease.
• Do not apply any oil to the inside of the hub, otherwise the grease will come out.
• You should periodically wash the sprockets in a neutral detergent and then lubricate them again. In addition, cleaning the
chain with neutral detergent and lubricating it can be a effective way of extending the useful life of the sprockets and the
chain.
• If the chain keeps coming off the sprockets during use, replace the sprockets and the chain.
• Use an outer casing which still has some length to spare even when the handlebars are turned all the way to both sides.
Furthermore, check that the shifting lever does not touch the bicycle frame when the handlebars are turned all the way.
• Grease the inner cable and the inside of the outer casing before use to ensure that they slide properly.
• Use a frame with internal cable routing is strongly discouraged as it has tendencies to impair the SIS shifting function due
to its high cable resistance.
• Operation of the levers related to gear shifting should be made only when the front chainwheel is turning.
• For smooth operation, use the specified outer casing and bottom bracket cable guide.
• To ensure the best performance, be sure to use only the specified type of chain. The wide type chain cannot be used.
• For maximum performance we highly recommend Shimano lubricants and maintenance products.
• Parts are not guaranteed against natural wear or deterioration resulting from normal use.
• For any questions regarding methods of installation, adjustment, maintenance or operation, please contact a professional
bicycle dealer.
Chain toolChain
9-speed super narrow chain
such as
CN-7701 / CN-HG93
8- / 7- / 6-speed narrow
chain such as
CN-HG50 / CN-HG40
Reinforced
connecting pin
TL-CN32 /TL-CN27
TL-CN32 /TL-CN27
6.5mm
7.1mm
Silver
Black
Reinforced Connecting Pin
End Pin Link Pin
Series
Gears
Shifting lever
Chain
Bottom bracket cable guide
Right
Rear derailleur
Outer casing
Multiple freewheel
Tourney
7-gears
SL-RS43-7
CN-HG50
SM-SP18/SM-BT18
RD-TX70/RD-TX50
RD-TX30
SIS
MF-TZ37/HG50
MF-HG37/TZ07
6-gears
SL-RS43-6
RD-TX70/RD-TX50
RD-TX30/RD-TY18
MF-HG40-6/HG22
MF-TZ06
In order to realize the best performance, we recommend that the following combination be used.
7-gears
SL-RS43-7
CN-HG50
SM-SP18/SM-BT18
RD-TX70/RD-TX50
RD-TX30
RD-FT30
SIS
MF-TZ37/TZ07
MF-HG50
6-gears
SL-RS43-6
RD-TX70/RD-TX50
RD-TX30/RD-TY18
RD-FT30
MF-HG40-6/HG22
MF-TZ06
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222
3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
Please note: specifications are subject to change for improvement without notice.(English)
© Jul. 2007 by Shimano Inc. XBC IZM Printed in Singapore.
This service instruction explains how to use
and maintain the Shimano bicycle parts
which have been used on your new bicycle.
For any questions regarding your bicycle or
other matters which are not related to
Shimano parts, please contact the place of
purchase or the bicycle manufacturer.
Specifications Cable securing and stroke adjustment
SIS Adjustment
Shifting lever
Rear derailleur
Sprocket tooth configurations
Mounting the shifting lever Gear shifting operation
Tightening torque:
2 N·m {18 in. lbs.}
Handlebar
Pedaling becomes
heavier
Pedaling becomes
lighter
3 mm Allen Key
Half grip
Install the brake lever in a position where it will not obstruct brake
operation.
Do not use in a combination which causes brake operation to be
obstructed.
Leave a gap of 0.5 mm between
the Revo-shift lever and the half grip.
Tightening torque:
8 - 10 N·m
{70 - 86 in. lbs.}
Installation of the rear derailleur
Installation of the freewheel
Direct-mount type
< GS >
5 mm Allen Key
Frame
Bracket
Push in and tighten
Freewheel removal tool
TL-FW30
Tightening torque:
3 - 4 N·m
{26 - 34 in. lbs.}
Bracket type
Bracket nut
Bracket bolt
Tightening torque:
30 N·m {260 in. lbs.}
To install
To disassemble
Chain length
Add 2 links (with the chain on
both the largest sprocket and
the largest chainring)
Largest
sprocket
Largest
chainring
Chain
Chain
< SS >
Smallest
sprocket
Largest
chainring
Guide pulley
Tension pulley 90°
Right angle to the ground
< RD-TX70 / RD-TX50 / RD-FT30 >
Place the outer casing so that it does not touch the basket and
mudguard, otherwise it may cause a problem with the performance
of the derailleur.
Set the outer casing (RD-TX70/RD-TX50/RD-FT30) so that its
length is as follows.
Connect the inner cable to the
derailleur as shown in the illustration.
• If routing the casing upward:
(The chain should be on the largest chainring and
on the largest sprocket.)
Add 10 mm to the length of the outer casing from
the end that is inserted into the outer casing holder
to the end which is inserted into the link.
• If routing the casing downward:
(The chain should be on the largest chainring and on the largest
sprocket.)
Set the length of the outer casing so that it describes a smooth
arc, and so that the link stops in a position where there is a small
gap between the link and the link stop.
L
Chain position
Largest
sprocket
Largest
chainring
Chain position
Largest
sprocket
Largest
chainring
Outer casing
holder
Link
max.
angle
max.
angle
Link
Link stop
Inner cable
1. Top adjustment
Turn the top adjustment screw to adjust so that the guide pulley is
below the outer line of the smallest sprocket when looking from the
rear. After this, install the chain.
2. Connection and securing of cable
Connect the cable to the rear derailleur and, after taking up the initial
slack in the cable, reattach to the rear derailleur as shown in the
illustration.
Secure the cable by pulling it with pliers with a force of 5 - 10 kg.
3. Low adjustment
Turn the low adjustment screw so that the guide pulley moves to a
position directly below the largest sprocket.
4. How to use the B-tension adjustment screw
< RD-TX70 / RD-TX50 / RD-TX30 >
Mount the chain on the smallest chainring and the largest sprocket,
and turn the crank arm backward. Then turn the B-tension adjustment
screw to adjust the guide pulley
as close to the sprocket as
possible but not so close that it
touches.
Next, set the chain to the
smallest sprocket and repeat
the above to make sure that the
pulley does not touch the
sprocket.
Operate the shifting lever several times to move
the chain to the 2nd sprocket. Then, while
pressing the lever just enough to take up the play
in the lever, turn the crank arm.
1 2
1
2
Top adjustment
screw
RD-TX70/TX50/TX30
RD-FT30
RD-TY18
Outer line of
smallest sprocket
Guide pulley
Tightening torque:
5 - 7 N·m {44 - 60 in. lbs.}
Groove
Pull
Note:
Be sure that the cable is
securely in the groove.
Cutting the outer casing
When cutting the outer casing, cut the opposite
end to the end with the marking. After cutting the
outer casing, make the end round so that the
inside of the hole has a uniform diameter.
Inserting the inner cable
Insert the inner cable into the outer casing from the end with the
marking on it. Apply grease from the
end with the marking in order to
maintain cable operating efficiency.
Attach the same outer end
cap to the cut end of the
outer casing.
Outer end cap
Marking
1
2
1 2
Low adjustment
screw
RD-TX70/TX50/TX30
RD-FT30
RD-TY18
Largest
sprocket
Guide pulley
Replacing the inner cable
Replace the inner cable by carrying out
steps
1 to 3 as shown in the
illustrations.
Largest sprocket Smallest sprocket
B-tension
adjustment screw
Play
When shifting
to 3rd
When no sound at
all is heard
For the best SIS performance, periodically lubricate all powertransmission parts.
Tighten the outer cable adjusting
barrel until the chain returns to
the 2nd sprocket. (clockwise)
Loosen the outer casing
adjustment barrel until the chain
touches the 3rd sprocket and
makes noise. (counter clockwise)
adjustment
ballel
RD-TX70/50
RD-FT30
RD-TX30
Best setting
The best setting is when the shifting lever is operated
just enough to take up the play and the chain touches
the 3rd sprocket and makes noise.
* Return the lever to its original position (the position
where the lever is at the 2nd sprocket setting and it has
been released) and then turn the crank arm clockwise.
If the chain is touching the 3rd sprocket and making noise, turn the
outer casing adjustment barrel clockwise slightly to tighten it until the
noise stops and the chain runs smoothly.
Operate lever to change gears, and check that no noise occurs in any
of the gear positions.
adjustment
ballel
RD-TX70/50
RD-FT30
RD-TX30
1
2
3
RD-FT30
SS
7 / 6
17T
28T
11T
––
GS
6
34T
28T
14T
20T
SS
6
28T
28T
14T
13T
RD-TY18
Loading...