Page 1
(English)
DM-LP0002-02
Dealer's Manual
Front light
LP-C2100
LP-C2101
LP-C2111
LP-X101
(6V-0.9W specification)
LP-X102
(6V-0.9W specification)
Page 2
IMPORTANT NOTICE
The following instructions must be observed at all times in order to prevent personal injury and physical damage to
equipment and surroundings.
The instructions are classified according to the degree of danger or damage which may occur if the product is used
incorrectly.
DANGER
Failure to follow the instructions will result in death or serious injury.
WARNING
Failure to follow the instructions could result in death or serious injury.
CAUTION
Failure to follow the instructions could cause personal injury or physical damage to equipment and surroundings.
•
This dealer’s manual is intended primarily for use by professional bicycle mechanics.
Users who are not professionally trained for bicycle assembly should not attempt to install the components themselves using the
dealer’s manuals.
If any part of the information on the manual is unclear to you, do not proceed with the installation. Instead, contact your place
of purchase or a local bicycle dealer for their assistance.
•
Make sure to read all instruction manuals included with the product.
•
Do not disassemble or modify the product other than as stated in the information contained in this dealer’s manual.
•
All dealer’s manuals and instruction manuals can be viewed on-line on our website (http://si.shimano.com).
•
Please observe the appropriate rules and regulations of the country, state or region in which you conduct your business as a
dealer.
For safety, be sure to read this dealer’s manual thoroughly before use, and follow it for correct use.
2
Page 3
TO ENSURE SAFETY
WARNING
•
When installing components, be sure to follow the instructions that are given in the instruction manuals.
It is recommended to use genuine Shimano parts only. If parts such as bolts and nuts become loose or damaged, the bicycle may
suddenly fall over, which may cause serious injury.
In addition, if adjustments are not carried out correctly, problems may occur, and the bicycle may suddenly fall over, which may
cause serious injury.
•
Be sure to wear safety glasses or goggles to protect your eyes while performing maintenance tasks such as replacing parts.
•
After reading the dealer's manual thoroughly, keep it in a safe place for later reference.
CAUTION
•
A hub dynamo will provide higher power generation capacity. When riding or rotating the wheels, never touch the connection
terminals of the hub dynamo. If this is not observed, you could receive an electric shock.
Be sure to also inform users of the following:
•
Check that the front light is on during night riding.
NOTE
Be sure to also inform users of the following:
•
Connect and use a hub dynamo that is compatible with the light.
•
Check that the hub dynamo connection terminal is securely connected before using the hub dynamo.
•
Lighting may flicker at speeds between 4 and 10 km/h.
•
The front light is always turned on when riding.
•
The light bulb for the LED-equipped front and tail light cannot be replaced; replace the device.
•
This product supports only a 6V, 0.9W hub dynamo. Use a 0.9W Shimano hub dynamo.
•
Make sure that the front light does not dazzle oncoming persons.
•
The sensor-equipped LED light automatically lights up depending on the ambient light intensity detected by the illumination
sensor receiver.
If it lights up earlier than it should, clean the illumination sensor receiver.
•
The illumination sensor of the LED light works at a speed of approximately 4 km/h or higher, it does not light up at lower
speeds, such as shortly after the bicycle starts to travel.
For Installation to the Bicycle, and Maintenance:
•
Also read the manual for the hub dynamo.
•
Products are not guaranteed against natural wear and deterioration from normal use and aging.
•
For maximum performance we highly recommend Shimano lubricants and maintenance products.
The actual product may differ from the illustration because this manual is intended mainly to explain the procedures for
using the product.
3
Page 4
INSTALLATION
Tightening torque:
5 - 6 N·m {44 - 52 in. lbs.}
Tightening torque:
•
These lights adhere to Japanese Industrial Standards (JIS) when used within the system.
Light
6V - 0.9W hub dynamos with the J2-A terminal, such as
DH-C2100, are supported.
List of tools to be used
Where to use Tool
Front light 10 mm spanner, Screwdriver #2
Installing the front light
Light stay type
J2-A terminal
Connector
Install the LED light to the dynamo mount stay for the front fork as shown in the illustration below.
Dynamo mount stay
Mounting nut
Mounting bolt with
spring washer
When installing, make sure that the lines on the
installation section of the LED light are perpendicular.
* Not compatible with LP-X101/LP-X102
LED light
10 mm spanner
4
Page 5
Under basket mount type
Screw tightening torque:
3 - 4 N·m {27 - 34 in. lbs.}
Tightening torque:
6 - 7 N·m {53 - 61 in. lbs.}
Install the LED light in the order shown in the illustration below.
At that time, install the LED light so that the light does not shift between the basket stay and the front basket.
Screwdriver #2
Front basket-fixing
bolt (M5)
Front basket
Basket stay
Fitting
LED light
10 mm spanner
Angle adjustment bolt
After installation, adjust the light so that the lines on
the installation section of the LED light are level.
Note:
The cable and tire may come into close proximity.
When installing, ensure that there is sufficient distance from the tire.
5
Page 6
Connecting the hub dynamo
In the case of a basket stay is supplied
Wind the LED light cable around the basket stay, and attach the connector to the connecting terminal for the hub dynamo.
Cable
J2-A terminal
Cable fixing
clip
Connector
Basket stay
Connect
Connecting terminal
In the case of a basket stay is not supplied
Wind the LED light cable around the front fork, and attach the connector to the connecting terminal for the hub dynamo.
Cable
Front fork
If the cable loosens, fix it with a zip tie.
J2-A terminal
Connector
Connect
Connecting terminal
6
Page 7
Connecting the cable and the connector
Note:
•
Twist the cable wires before connecting them so that they stay together.
•
Wire specifications
Marking
Connector
Light connection terminal
Hub dynamo connection terminal
Wire
Note:
If you wish to replace the connector or change the length of
the cable, perform the following procedure.
•
Open the connector using a
slotted screwdriver or the like
as shown in the figure.
•
Insert the cable with the
marking into the ground side
of the connector.
•
Twist the cable wires, pass
them through the connector,
bend them, and run them
along the grooves.
Size (AWG) 22
Diameter approx. 0.8 mm
Approx.
16 mm
Ground side
Groove
Bend
Approx.
16 mm
Insert
•
Do not allow the cable wires
to touch each other.
•
Close the connector until you
hear a click.
7
Page 8
Please note: specifications are subject to change for improvement without notice. (English)
© Jun. 2015 by Shimano Inc. HTR
Loading...