Sharp XV-Z7000E User Manual

Page 1
Before using the LCD projector, please read this operation manual carefully.
OPERATION MANUAL ENGLISH
ENGLISH
Important
IMPORTANT
Information
For your assistance in reporting the loss or theft of your Colour LCD Projector, please record the Serial Number located on the bottom of the projector and retain this information. Before recycling the packaging, please be sure that you have checked the contents of the carton thoroughly against the list of “Supplied Accessories” on page 10.
WARNING:
Intense light source. Do not look into the beam or view it directly. Be especially careful that children do not look directly into the beam.
WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to liquids.
CAUTION:
To reduce the risk of electric shock, do not remove cabinet. No user-serviceable parts are inside. Refer servicing to qualified service personnel.
Model No.: XV-Z7000E
Serial No.:
1
Page 2
WARNING:
The cooling fan in this projector continues to run for about 90 seconds after the projector is turned off. During normal operation, when turning the power off always use the ON/OFF button on the projector or the POWER button on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord. DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
Caution Concerning the Lamp Replacement
See Replacing the Projection Lamp on pages 38 and 39.
ENGLISH
Information
Important
LAMP REPLACEMENT CAUTION
BEFORE REMOVING THE SCREW, DISCONNECT POWER CORD. HOT SURFACE INSIDE. ALLOW 1 HOUR TO COOL BEFORE REPLACING THE LAMP. REPLACE WITH SAME SHARP LAMP UNIT TYPE BQC-PGC20X // 1 ONLY. UV RADIATION : CAN CAUSE EYE DAMAGE. TURN OFF LAMP BEFORE SERVICING. MEDIUM PRESSURE LAMP : RISK OF EXPLOSION. POTENTIAL HAZARD OF GLASS PARTICLES IF LAMP HAS RUPTURED. HANDLE WITH CARE. SEE OPERATION MANUAL.
USER SERVICE SCREW VIS POUR ENTRETIEN PAR L’UTILISATEUR
PRECAUTIONS A OBSERVER LORS DU REMPLACEMENT DE LA LAMPE.
DEBRANCHER LE CORDON D’ALIMENTATION AVANT DE RETIRER LES VIS. L’INTERIEUR DU BOITIER ETANT EXTREMEMENT CHAUD, ATTENDRE 1 HEURE AVANT DE PROCEDER AU REMPLACEMENT DE LA LAMPE. NE REMPLACER QUE PAR UNE LAMPE SHARP DE TYPE BQC- PGC20X// 1. RAYONS ULTRAVIOLETS : PEUVENT ENDOMMAGER LES YEUX. ETEINDRE LA LAMPE AVANT DE PROCEDER A L’ENTRETIEN. LAMPE A MOYENNE PRESSION : RISQUE D’EXPLOSION. DANGER POTENTIEL DE PARTICULES DE VERRE EN CAS D’ECLATEMENT DE LA LAMPE. A MANIPULER AVEC PRECAUTION, SE REPORTER AU MODE D’EMPLOI.
2
Page 3
Important Safeguards
ATTENTION: Please read all of these instructions before you operate your LCD Projector for the first time. Save these instructions for future reference.
Important
Information
For your own protection and prolonged operation of your LCD Projector, be sure to read the following “Important Safeguards carefully, before use. This projector has been engineered and manufactured to ensure your personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated into this LCD Projector, observe the following basic rules for its installation, use and servicing.
1. Unplug the LCD Projector from the wall outlet before cleaning.
2. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
3. Do not use attachments not recommended by the LCD Projector manufacturer, as they may cause hazards.
4. Do not use the LCD Projector near water; for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, near a swimming pool, etc. Never spill liquid into the projector.
5. Do not place the LCD Projector on an unstable cart, stand, or table. The LCD Projector may fall, which may cause serious injury to a child or an adult, and/or serious damage to the unit.
6. Wall or Ceiling MountingThe product should be mounted to a wall or ceiling only as recommended by the manufacturer.
7. LCD Projector equipment and cart combinations should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the equipment and cart combination to overturn.
8. Slots and openings in the cabinet back and bottom are provided for ventilation. To ensure reliable operation of the LCD Projector and to protect it from overheating, these openings must not be blocked or covered. The openings should never be covered with cloth or other material.
9. This LCD Projector should never be placed near or over a radiator or heating vent. The LCD Projector should not be placed in a built-in installation such as a bookcase unless proper ventilation is provided.
10. The LCD Projector should be operated only from the type of power source indicated on the back of the projector or in the specifications. If you are not sure of the type of power supplied to your home, consult your LCD Projector dealer or local power company.
11. Do not place the LCD Projector where the cord will be abused by persons walking on it.
12. Follow all warnings and instructions marked on the LCD Projector.
13. To prevent damage to the projector due to lightning and power-line surges, unplug the projector from the power outlet, when not in use.
14. Do not overload wall outlets and extension cords with too many products, because this can result in fire or electric shock.
15. Never push objects of any kind into the LCD Projector through the cabinet slots as they may touch high-voltage points or cause a short circuit. This could result in a fire or electric shock.
16. Do not attempt to service the LCD Projector yourself. Opening or removing covers may expose you to dan­gerous voltage or other hazards. Refer all servicing to qualified service personnel.
17. Unplug the LCD Projector equipment from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the LCD Projector. c. If the LCD Projector has been exposed to rain or
water.
d. If the LCD Projector does not operate normally
when you follow the operating instructions. Adjust only those controls that are covered by the oper­ating instructions, as improper adjustment of other controls may cause damage and will often require extensive work by a qualified technician to restore the LCD Projector to normal operation.
e. If the LCD Projector has been dropped or the
cabinet has been damaged.
f. When the LCD Projector exhibits a distinct change
in performancethis indicates a need for service.
18. When replacement parts are required, be sure the ser­vice technician has used replacement parts specified by the manufacturer that have the same characteristics as the original parts. Unauthorised substitutions may result in fire, electric shock, or other hazards.
19. This LCD Projector is provided with one of the following types of plugs. If the plug should fail to fit into the power outlet, please contact your electrician. Do not defeat the safety purpose of the plug.
a. Two-wire type mains plug. b. Three-wire grounding type mains plug with a
grounding terminal. This plug will only fit into a grounding type power outlet.
3
Page 4
Outstanding Features
1. WIDESCREEN IMAGES
Allows projection of DVD, DTV and other anamorphic images recorded in widescreen format with a 16:9 aspect ratio. (Page
31)
2. BRIGHTNESS SWITCHOVER FUNCTION
Function with toggle switch to control the quantity of projected light. Select “ON” or “OFF” to decrease or increase brightness, power consumption and fan noise. (Page 33)
3. FOR USE WITH DTV*
Allows projection of DTV images and 16:9 wide-screen images when connected to a DTV decoder or similar video systems. (Page 11)
4. ADVANCED VIDEO CIRCUITRY
Provides high quality images with minimal dot crawl and cross colour noise.
5. 3D DIGITAL UNIFORMITY
Equipped with new 3D digital uniformity technology for a clearer, more uniform image.
6. NEW PROGRESSIVE MODE AND FILM MODE
Optimises the image by converting the interlaced signal to the progressive. Useful for displaying slow-moving images or still images. Four modes are available, and the film mode beautifully reproduces movie film recorded in 24 Hz progressive format. (Page 25)
7. ANALOG COMPONENT VIDEO INPUT
Utilises a component video input signal (Y, CB, CR). The video signal is input as separate components to provide superior colour and image quality.
Information
Important
8. ACTIVE DIGITAL KEYSTONE CORRECTION
Corrects keystone distortion caused when the projected image is not perpendicular to the screen. This method provides not only horizontal correction, but vertical as well, thus maintaining the original 4:3 aspect ratio and eliminating jag lines. (Page 19)
9. EASY-TO-USE GRAPHICAL USER INTERFACE (GUI)
A multi-colour menu system allows for simple image adjustments. (Page 20)
10. COLOUR TEMPERATURE ADJUSTMENT
The function can be used to adjust the colour temperature to suit the type of image input to the projector. (Page 29)
11. GAMMA CORRECTION FUNCTION
The gamma value setting can be adjusted according to the input source for optimal image contrast. (Page 30)
12. DIRECT COMPUTER COMPATIBILITY
A multi-scan RGB input accepts signals from VGA (640 dots 480 lines) to SXGA (1,280 dots 1,024 lines) and Macintosh (from 13) compatible computers without the need for any additional hardware.
*DTV is the umbrella term used to describe the new digital television system in the united states.
4
Page 5
Contents
Important Information
Important Safeguards …………………………… 3
Important
Information
Outstanding Features …………………………… 4 Contents …………………………………………… 5 Usage Guidelines ………………………………… 6 Part Names ………………………………………… 7
Setup & Connections
Supplied Accessories …………………………… 10 Connecting the Projector ……………………… 11
Setup & Connections
Operation
Operation
Basic Operations ………………………………… 15 Setting up the Screen …………………………… 17 Using the GUI (Graphical User Interface)
Menu Screens ………………………………… 20 Selecting the On-screen Display Language … 23 Selecting the Video Input System Mode
(S-VIDEO or VIDEO mode only) …………… 23 Picture Adjustments ……………………………… 24
Adjusting the Picture …………………………… 24
Selecting the Signal Type ……………………… 25
Progressive Mode ……………………………… 25
Computer Image Adjustments
(INPUT 2 (RGB) mode only) ………………… 26
Auto Sync Adjustment ………………………… 26
Adjusting the Computer Image ……………… 27
Useful Features
Freeze Function …………………………………… 28 Adjusting the Colour Temperature …………… 29 Gamma Correction ……………………………… 30 Selecting the Picture Display Mode …………… 31 Checking the Input Signal
and the Lamp Usage Time …………………… 32 Automatic Power Shutoff Function …………… 32 Selecting a Background Image ………………… 33 Theatre Mode Function ………………………… 33 Reverse/Invert Image Function ………………… 34 Special Mode Adjustment ……………………… 34
Maintenance & Troubleshooting
Air Filter Maintenance …………………………… 35 Lamp/Maintenance Indicators ………………… 37 Replacing the Projection Lamp ………………… 38 Using the Kensington Lock …………………… 40 Troubleshooting …………………………………… 40
Appendix
Attaching the Lens Cap ………………………… 41 Connection Pin Assignments…………………… 42 RS-232C Port Specifications …………………… 43 Computer Compatibility Chart ………………… 45 Specifications ……………………………………… 46 Dimensions ………………………………………… 47 Glossary …………………………………………… 48
Useful Features
Maintenance &
Troubleshooting
Appendix
5
Page 6
Usage Guidelines
CAUT I ON
ATTENTI ON
BQC-PGC20X //1
35˚C
5˚C
Caution Concerning the Lamp Unit
Potential hazard of glass particles if lamp ruptures. Please have the nearest Sharp Authorised LCD Projector Dealer or Service Centre replace lamp if rupture occurs. See Replacing the Projection Lamp on pages 38 and 39.
Cautions Concerning the Setup of the Projector
For minimal servicing and to maintain high image quality, SHARP recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. If the projector is used in these environments, the lens and filter will need to be cleaned (or the filter replaced) more often, and internal cleaning may become necessary. As long as the projector is regularly cleaned, use in these environments will not reduce the overall operation life of the unit. Internal cleaning should only be performed by a Sharp Authorised LCD Projector Dealer or Service Centre.
Do not expose the projector to extreme heat or cold. Operating temperature: Ⳮ5°C to Ⳮ35°C Storage temperature: 20°C to 60°C
Information
Important
Notes on Operation
The mark shown on the left calls the users attention to a part of the projector that emits intense heat during operation.
The exhaust vent, the lamp cage cover and adjacent areas may be extremely hot during projector operation. To prevent injury, do not touch these areas until they have sufficiently cooled.
Allow at least 10 cm of space between the cooling fan (exhaust vent) and the nearest wall or obstruction.
If the cooling fan becomes obstructed, a protection device will automatically turn off the projector lamp. This does not indicate a malfunction. Remove the projector power cord from the wall outlet and wait at least 10 minutes. Then turn on the power by plugging the power cord back in. This will return the projector to the normal operating condition.
Temperature Monitor Function
If the projector starts to overheat due to setup problems or a dirty air filter, “TEMP. will appear in the lower-left corner of the picture. If the temperature continues to rise, the lamp will turn off, the TEMPERATURE WARNING indicator on the projector will flash, and after a 90-second cooling-off period the power will shut off. Refer to Lamp/Maintenance Indicators on page 37, for details.
The cooling fan regulates the internal temperature, and its performance is automatically controlled. The sound of the fan may change during projector operation due to changes in the fan speed.
Lamp Monitor Function
When the projector is turned on after the lamp has been used for 900 hours, LAMP will appear in the lower-left corner of the picture to advise you to replace the lamp. See pages 38 and 39 for lamp replacement. If the lamp has been used for 1,000 hours, the projector power will automatically turn off and the projector will enter standby mode. Refer to Lamp/Maintenance Indicators on page 37, for details.
6
Page 7
Part Names
Numbers next to the part names refer to the main pages in this manual where the topic is explained.
Important
Projector
Information
Front and Top View
ON/OFF button
POWER indicator
INPUT/BACK button
KEYSTONE/Adjustment
(/ƒ) buttons
ZOOM knob
FOCUS ring
Cooling fan (Exhaust vent)
Foot releases
15
15
16 20
19 20
15
15
6
18
ON/OFF
POWER
KEYSTONE
INPUT
BACK ENTER MENU
LAMP
TEMP.
PICT MODE
LAMP REPLACEMENT
37
indicator
TEMPERATURE WARNING
37
indicator
31
PICT MODE/ENTER button
20
MENU button
20
Air filter/Cooling fan
35
(Intake vent)
Speaker
Remote control sensor
9
Eyelet for
41
lens cap strap
Side and Rear View
S-VIDEO INPUT terminal
(4-pin Mini DIN)
VIDEO INPUT terminal
(RCA)
AUDIO INPUT
(S-VIDEO, VIDEO INPUT )
terminals (RCA)
S-VIDEO INPUT
11
11
11
VIDEO INPUT
AUDIO INPUT
(S-VIDEO, VIDEO INPUT)
LR
RS-232C
INPUT 1 INPUT 2/COMPONENT
AUDIO INPUT
(INPUT 1, 2)
Kensington Security
40
Standard connector
AC socket
11
Remote control sensor
9
RGB /COMPONENTCRCBY
INPUT 2 RGB/COMPONENT
12
port (HD 15) AUDIO INPUT (INPUT 1, 2)
terminal
12
(3.5 mm stereo minijack)
INPUT 1/COMPONENT
12
terminals (RCA: Y, C
RS-232C port
14
(9-pin Mini DIN)
B, CR)
7
Page 8
Part Names
Remote Control
Information
Important
Front View
VOLUME buttons
MUTE button
Mouse (∂/ƒ)/
Adjustment (∂/ƒ)
buttons
RGB/COMPONENT
button
INPUT 1 button
INPUT 2 button
S-VIDEO button
VIDEO button
16
16
20
12
16
16
16
16
VOL
MUTE
BACK
ENTER
RGB/
COMPONENT
INPUT 1
AUTO SYNCINPUT 2 GAMMA
S-VIDEO CLR TEMP
KEYSTONE
VIDEO FREEZE
POWER
MENU
PICT MODE
POWER button
15
BACK button
20
MENU button
20
ENTER button
20
AUTO SYNC button
26
PICT MODE button
31
GAMMA button
30
CLR TEMP button
29
Top View
Remote control signal transmitter
KEYSTONE buttons
19
FREEZE button
28
Inserting the Batteries
Slide in the direction of
13
the arrow to remove the battery cover.
If the remote control gets wet, wipe it dry immediately.
Avoid excessive heat and humidity.
If you will not be using the remote control for a long time, remove the batteries.
Do not mix new and old or different types of batteries.
There are operations that can only be carried out by remote control. Handle the remote control carefully.
Insert two AAA size
2
batteries, making sure their polarities match the and marks inside the battery compartment.
Insert the side tabs of the battery cover into their slots and press the cover in until it is properly seated.
8
Page 9
Part Names
Attaching the Rubber Leg Tips
The rubber leg tips are provided to prevent the remote
Important
Information
control from skidding and shaking over a flat surface.
Positioning the Remote Control
The remote control can be used to control the projector within the ranges shown below.
The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may differ due to the screen material.
Remote control
7 m
30˚
30˚
45˚
45˚
30˚
Remote control
9
Page 10
Setup & Connections
Supplied Accessories
Remote control
Two AAA size batteries
Power cord
For Europe, Hong Kong and Singapore
(For Europe, except U.K.) (For U.K., Hong Kong and Singapore)
• The configuration of wall outlets differs from country to country. Use the power cord that corresponds to the wall outlet in your country.
Rubber leg tips for remote control
For Australia, New Zealand, and Oceania
Setup & Connections
For Europe only
Computer RGB cable
The RGB cable and 21 pin conversion adaptor are only supplied with European models.
A/V cable
Extra air filter
Lens cap
21 pin RCA conversion adaptor
DIN-D-sub RS-232C cable
Lens cap strap
Two LCD projector operation manuals
10
Page 11
Connecting the Projector
Connecting the Power Cord
Plug the supplied power cord into the AC socket on the back of the projector.
Power cord
Setup & Connections
CAUTION
Make sure you connect the power cord firmly into the AC socket.
The configuration of wall outlets differs from country to country. Use the power cord that corresponds to the wall outlet in your country.
Connecting the Projector to Audiovisual Equipment
You can connect your projector to a VCR, laser disc player, DVD player, DTV decoder* and other audiovisual equipment.
CAUTION
Always turn off the projector while connecting to audiovisual equipment, in order to protect both the projector and the equipment being connected.
Connecting a video source (VCR, laser disc player, DTV decoder or DVD player) using the standard video and audio input
1 Connect one end of the S-video cable to the S-VIDEO
INPUT terminal, or one end of the video cable to the
OR
VIDEO INPUT terminal on the projector and the video
output terminal on the video source.
2 To use the built-in audio system, connect the RCA
connectors to the corresponding AUDIO INPUT (S- VIDEO, VIDEO INPUT) terminals on the projector and the audio output terminals on the audiovisual source.
The S-VIDEO INPUT terminal uses a video signal system in which the picture is separated into a colour and a luminance signal to realise a higher-quality image.
For higher quality video, you may use the S-VIDEO INPUT terminal on the projector. S-video cable is sold separately.
If your video equipment does not have an S-video output terminal, use the composite video output terminal.
Projector
VIDEO
S-VIDEO INPUT
* DTV is the umbrella term used to describe the new digital television system in the united
states.
11
INPUT
AUDIO INPUT
(S-VIDEO, VIDEO INPUT)
LR
2 Audio cable (sold separately)
To audio output terminals
1 Video cable (sold separately)
OR
To video output terminal
1 S-video cable (sold separately)
To S-video output terminal
VCR,
Laser disc player,
DTV decoder or
DVD player
Page 12
Connecting the Projector
Connecting an audiovisual source (DTV decoder or DVD player) using the RCA input
1 Connect each RCA connector to the corresponding
INPUT 1/COMPONENT terminals on the projector.
2 Connect the other end of the cable to the corresponding
terminals of a DVD player or DTV decoder.
3 To use the built-in audio system, connect one end of an
audio cable to the AUDIO INPUT (INPUT 1, 2) terminal on the projector. Connect the other end to the audio output terminal on the audiovisual equipment.
A 3.5 mm minijack to RCA audio cable adaptor may be necessary.
When connecting this projector to a DVD player or a DTV decoder, select “Component” by using RGB/COMPONENT on the remote control or the GUI menu. (See page 25.)
Setup & Connections
Projector
RS-232C
INPUT 1 INPUT 2/COMPONENT
C
Y
AUDIO INPUT (INPUT 1, 2)
R
B
RGB /COMPONENTC
Audio cable (sold separately)
To audio output terminals
RCA component cable (sold separately)
To analog component output terminals
Connecting an audiovisual source (DTV decoder or DVD player) using the 15 pin video and audio input
1 Connect the one end of the D-sub/RCA cable to the
INPUT 2 RGB/COMPONENT port on the projector.
2 Connect the other end of the cable to the corresponding
terminals of a DVD player or DTV decoder.
3 To use the built-in audio system, connect one end of an
audio cable to the AUDIO INPUT (INPUT 1, 2) terminal on the projector. Connect the other end to the audio output terminal on the audiovisual equipment.
A 3.5 mm minijack to RCA audio cable adaptor may be necessary.
DTV decoder
or
DVD player
When connecting this projector to a DVD player or a DTV decoder, select “Component” by using RGB/COMPONENT on the remote control or the GUI menu. (See page 25.)
Projector
AUDIO INPUT
(INPUT 1, 2)
INPUT 2
RGB /COMPONENTP
D-sub/RCA cable (sold separately)
To analog component output terminals
Audio cable (sold separately)
To audio output terminals
DTV decoder
or
DVD player
ENT
R
12
Page 13
Connecting the Projector
Connecting the Projector to a Computer
You can connect your projector to a computer for projection of full color computer images.
Connecting a computer using the standard 15-pin video and audio input
For Europe only
Computer RGB cable
1 Connect one end of the computer RGB cable to the
INPUT 2 RGB/COMPONENT port on the projector. Secure the connector by tightening the thumb screws.
2 Connect the other end to the Monitor output port on the
Setup & Connections
computer. Secure the connector by tightening the thumb screws.
3 To use the built-in audio system, connect one end of
the computer audio cable to the AUDIO INPUT (INPUT 1, 2) terminal on the projector.
4 Connect the other end to the Audio output terminal on
the computer.
CAUTION
Before connecting, be sure to turn both the projector and the computer off. After making all connections, turn the projector on first. The computer should always be turned on last.
Please read the computers operation manual carefully.
Refer to page 45 Computer Compatibility Chart for a list of computer
RS-232C
INPUT 1 INPUT 2/COMPONENT
AUDIO INPUT
(INPUT 1, 2)
RGB /COMPONENTCRCBY
signals compatible with the projector. Use with computer signals other than those listed may cause some of the functions not to work.
A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Sharp Authorised LCD Projector Dealer or Service Centre.
When connecting this projector to a computer, select “RGB” by using RGB/COMPONENT on the remote control or the GUI menu. (See page 25.)
Connecting other compatible computers
When connecting the projector to a compatible computer other than an IBM-PC (VGA/SVGA/XGA/SXGA) or Mac­intosh (i.e. Workstation), a separate cable may be needed. Please contact your dealer for more information.
When connecting this projector to a computer, select “RGB” by using RGB/COMPONENT on the remote control or the GUI menu. (See page 25.)
Connecting computers other than the recommended types may result in damage to the projector, the computer, or both.
“Plug and Play” function
This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC compatible computer will communicate their setting requirements, allowing for quick and easy setup.
Before using the Plug and Play function, be sure to turn on the projector first and the connected computer last.
The DDC, Plug and Play function of this projector operates only when used in conjunction with a VESA DDC compatible computer.
13
Page 14
O
Connecting the Projector
Connecting RS-232C Port
When the RS-232C port on the projector is connected to a computer with an RS-232C cable (null modem, cross type, sold separately), the computer can be used to control the projector and check the status of the projector. See pages 43 and 44 for details.
DIN-D-sub RS-232C cable
1 Connect the supplied DIN-D-sub RS-232C cable to the RS-232C port on the projector. 2 Connect an RS-232C cable (null modem, cross type, sold separately) to the other end of DIN-D-sub RS-232C
cable and to the serial port on the computer.
Setup & Connections
(null modem, cross type, sold separately)
RS-232C cable
DIN-D-sub
RS-232C cable
Projector
RS-232C
INPUT 1 /C
Y
CAUTION
Do not connect or disconnect an RS-232C cable to or from the computer while it is on. This may damage your computer.
The RS-232C function may not operate if your computer port is not correctly set up. Please refer to the operation manual of
the computer for details on setting up.
A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Sharp Authorised LCD Projector Dealer or Service Centre.
P
B
14
Page 15
Operation
Basic Operations
Maintenance indicators
POWER
ON/OFF
KEYSTONE
LAMP
TEMP.
1 Make the necessary connections before pro-
ceeding. Connect the power cord to a wall outlet. The POWER indicator illuminates red and the projector enters standby mode.
• If the side filter cover is not securely installed, the POWER indicator flashes.
Operation
Projector
ON/OFF
KEYSTONE
LAMP
TEMP.
PICT MODE
POWER
INPUT
BACK ENTER MENU
Maintenance indicators
POWER
2
Startup image
ON/OFF
KEYSTONE
Remote control 2 Press ON/OFF on the projector for over one
second, or POWER on the remote control.
VOL
MUTE
LAMP
TEMP.
BACK
ENTER
POWER
MENU
The flashing green LAMP REPLACEMENT indicator shows that the lamp is warming up. Wait until the indicator stops flashing before operating the projector.
If the power is turned off and then immediately turned on again, it may take a short while before the lamp turns on.
After the projector is unpacked and turned on for the first time, a slight odour may be emitted from the exhaust vent. This odour will soon disappear with use.
Do not press any buttons before the startup image disappears. Before Adjusting The Image appears, only ON/OFF or POWER is available.
When the power is on, the LAMP REPLACEMENT indicator lights indicating the status of the lamp.
Green: Lamp is ready. Flashing green: Warming up. Red: Change the lamp.
15
3 4
3 Slide the ZOOM knob. The image can be adjusted
to the desired size within the zoom range.
4 Rotate the FOCUS ring until the image on the
screen becomes clear.
Page 16
Basic Operations
Projector Remote control
ON/OFF
KEYSTONE
LAMP
TEMP.
PICT MODE
POWER
INPUT
BACK ENTER MENU
8 6
MUTE
7
5
EXAMPLE
INPUT 1 Mode INPUT 2 Mode
5
g
d
VIDEO Mode S-VIDEO Mode
s
6
VOL
BACK
ENTER
RGB/
COMPONENT
INPUT 1
S-VIDEO CLR TEMP
VIDEO FREEZE
PICT MODE
AUTO SYNCINPUT 2 GAMMA
KEYSTONE
f
POWER
MENU
5 Press INPUT on the projector, INPUT 1, INPUT 2,
S-VIDEO or VIDEO on the remote control to select
the desired input mode. Press INPUT, INPUT 1, INPUT 2, S-VIDEO or VIDEO again to change the mode.
When the selected input signal is being received, Adjusting The Image will be displayed.
When no signal is being received, NO SIGNAL will be displayed. When a signal that the projector is not preset to receive is being received, NOT REG. will be displayed.
6 Press VOLUME on the remote control to adjust
the volume.
7 Press MUTE on the remote control to temporarily
turn off the sound. Press MUTE again to turn the sound back on.
8 Press ON/OFF on the projector for over one
second, or POWER on the remote control. Press ON/OFF or POWER again while the message is displayed.
If you accidentally pressed ON/OFF or POWER and do not want to turn off the power, wait until the power off screen disappears.
When ON/OFF or POWER is pressed twice, the POWER indicator will light up red and the cooling fan will run for about 90 seconds. The projector will then enter standby mode.
Wait until the cooling fan stops before disconnecting the power cord.
The power can be turned on again by pressing ON/OFF or POWER. When the power is turned on, the POWER indicator
and the LAMP REPLACEMENT indicator light green.
The POWER indicator flashes if the right side filter cover is not securely installed.
Operation
7
8
WARNING:
The cooling fan in this projector continues to run for about 90 seconds after the projector is turned off. During normal operation, when turning the power off always use the ON/ OFF button on the projector or the POWER button on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord. DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
16
Page 17
Setting up the Screen
Position the projector perpendicular to the screen with all feet flat and level to achieve an optimal image. Move the projector forward or backward if the edges of the image are distorted.
The projector lens should be centred in the middle of the screen. If the lens centre is not perpendicular to the screen, the image will be distorted, making viewing difficult.
Position the screen so that it is not in direct sunlight or room light. Light falling directly onto the screen washes out colours, making viewing difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.
A polarizing screen cannot be used with this projector.
Standard Setup (Front Projection)
Place the projector at the required distance from the screen according to the desired picture size. (See the table below.)
FULL Mode (4:3)
Operation
WIDE Mode (16:9)
Picture size (diag.) (x)
635 cm (250⬙) 508 cm (200⬙) 381 cm (150⬙) 254 cm (100⬙)
213 cm (84⬙) 183 cm (72⬙) 152 cm (60⬙) 102 cm (40⬙)
Picture size (diag.) (x)
572 cm (225⬙) 508 cm (200⬙) 381 cm (150⬙) 338 cm (133⬙) 269 cm (106⬙) 254 cm (100⬙)
234 cm (92⬙) 213 cm (84⬙) 183 cm (72⬙) 152 cm (60⬙) 102 cm (40⬙)
Projection distance (L)
Maximum
10.0 m
9.6 m
7.2 m
4.8 m
4.0 m
3.4 m
2.8 m
1.9 m
Projection distance (L)
Maximum
10.0 m
10.0 m
7.8 m
6.9 m
5.5 m
5.2 m
4.8 m
4.4 m
3.7 m
3.1 m
2.0 m
*1
*2 *3
Minimum
9.9 m
7.9 m
5.9 m
3.9 m
3.3 m
2.8 m
2.3 m
1.6 m
Minimum
9.8 m
8.7 m
6.5 m
5.7 m
4.6 m
4.3 m
4.0 m
3.6 m
3.1 m
2.6 m
1.7 m
Distance from the lens centre to the
bottom of the image (H)
38.1 cm
30.5 cm
22.9 cm
15.2 cm
12.8 cm
11.0 cm
9.1 cm
6.1 cm
Distance from the lens centre to the
bottom of the image (H)
9.3 cm8.3 cm6.2 cm5.5 cm4.4 cm4.2 cm3.8 cm3.5 cm3.0 cm2.5 cm1.7 cm
NORMAL Mode (4:3)
Picture size (diag.) (x)
457 cm (180⬙) 381 cm (150⬙) 254 cm (100⬙)
213 cm (84⬙) 183 cm (72⬙) 152 cm (60⬙) 102 cm (40⬙)
Values with a minus () sign indicate the distance of the lens centre below the bottom of the screen.
The values do not match up when applying the formula in *1 to *4 above. However, this is not a calculation
error.
For optimum focus, the recommended projection distance (L) is from 1.15m to 10.0m.
Projection distance (L)
Maximum
10.0 m
9.6 m
6.3 m
5.3 m
4.6 m
3.8 m
2.5 m
*4
Minimum
9.5 m
7.9 m
5.3 m
4.4 m
3.8 m
3.1 m
2.1 m
Distance from the lens centre to the
bottom of the image (H)
9.1 cm7.6 cm5.1 cm4.3 cm3.7 cm3.0 cm2.0 cm
17
Page 18
Setting up the Screen
Using the Adjustment Feet
You can adjust the height of the image by raising the projector with the foot releases.
1 Press the foot releases and lift the projector to the desired angle.
(Adjustable up to approximately 7° from the standard position.)
2 Remove your hands from the foot releases. Once the adjustment
feet have locked in position, release the projector.
3 If the screen is at an angle, the adjusters can be used to adjust
the angle of the image.
Returning the projector to its original position
While holding the projector, press the foot releases and slowly lower the projector to its original position.
When an adjustment is made, the image may become distorted (keystoned), depending on the relative positions of the projector and the screen.
CAUTION
Do not press the foot releases when the adjustment feet are extended without firmly holding the projector.
Do not hold the lens when lifting or lowering the projector.
When lowering the projector, be careful not to get your fingers caught in the area between the adjustment feet and the
projector.
Operation
Reversed Image Setup
Rear projection
Place a translucent screen between the projector and the audience.
Use the projectors menu system to reverse the projected image. (See page 34 for use of this function.)
Optimal image quality can be achieved when the projector is positioned perpendicular to the screen with all feet flat and level.
CAUTION
When using a mirror, be sure to carefully position both the projector and the mirror so the light does not shine into the eyes of the audience.
Projection using a mirror
When the distance between the projector and screen is not sufficient for normal rear projection, you can use a mirror to reflect the image onto the screen.
Place a mirror (normal flat type) in front of the lens.
Project the normal image onto the mirror.
The image reflected from the mirror is projected onto
the translucent screen.
Ceiling-mount Setup
It is recommended that you use the optional Sharp ceiling-mount bracket for this installation.
Before mounting the projector, contact your nearest Sharp Authorised LCD Projector Dealer or Service Centre to obtain the recommended ceiling-mount bracket (sold separately). (AN-TK202 ceiling-mount bracket, AN-TK201 extension tube, AN-Z7T ceiling adaptors for AN-TK202 or AN-TK201.)
When the projector is in the inverted position, use the upper edge of the screen as the base line.
Use the projectors menu system to select the appropriate projection mode. (See page 34 for use of this function.)
18
Page 19
Setting up the Screen
Digital Keystone Correction
When the image is distorted due to the projection angle, the digital keystone correction function allows you to correct it.
The digital keystone correction can be made by pressing KEYSTONE, or by setting Keystone correction in the GUI menu.
Operation
Projector Remote control
COMPONENT
ON/OFF
KEYSTONE
LAMP
TEMP.
PICT MODE
POWER
INPUT
BACK ENTER MENU
Projector
ON/OFF
KEYSTONE
LAMP
TEMP.
PICT MODE
POWER
INPUT
BACK ENTER MENU
1
2, 3, 4
2, 3
INPUT 1
AUTO SYNCINPUT 2 GAMMA
S-VIDEO CLR TEMP
VIDEO FREEZE
Remote control
VOL
MUTE
1, 5
(GUI) On-screen Display
RGB/
KEYSTONE
BACK
ENTER
PICT MODE
POWER
MENU
Using the KEYSTONE buttons
1 Press KEYSTONE to adjust the setting.
Using the GUI menu
1 Press MENU.
2 Press /ƒ to select Options, and then press
ENTER.
3 Press /ƒ to select Keystone, and then press
ENTER.
4 Press ∂/ƒ to move the mark to the desired
setting.
5 To exit from the GUI, press MENU.
To reset the keystone setting, press BACK.
Straight lines and the edges of the displayed image may
appear jagged, when adjusting the keystone setting.
19
Page 20
Using the GUI (Graphical User Interface) Menu Screens
Projector Remote control This projector has three sets of menu screens (INPUT 1
or 2 (COMPONENT), INPUT 2 (RGB) and S-VIDEO or VIDEO) that allow you to adjust the image and various projector settings. These menu screens can be operated from the projector or the remote control with the following buttons.
s
ON/OFF
POWER
TEMP.
KEYSTONE
INPUT
BACK ENTER MENU
PICT MODE
EXAMPLE
INPUT 1 or 2 (COMPONENT) mode
LAMP
7
2, 4, 6
3, 5
1, 8
VOL
MUTE
POWER
BACK
MENU
ENTER
(GUI) On-screen Display
Operation
INPUT 2 (RGB) mode
s
S-VIDEO or VIDEO mode
s
1 Press MENU to display the main menu. 2 Press /ƒ to select an adjustment item in the main menu. 3 Press ENTER to display the sub menu. 4 Press /ƒ to select an adjustment item in the sub menu. 5 Press ENTER to activate the selected adjustment item. 6 Press /ƒ to adjust the item. 7 Press BACK to return to the previous screen. 8 Press MENU to exit from the GUI.
• For details on items on the menu screen, see the tree charts on pages 21 and 22.
20
Page 21
Using the GUI (Graphical User Interface) Menu Screens
Items on the INPUT 1 or 2 (COMPONENT) Mode Menu Bar
Main menu Main menu
Picture1
Picture2
Options Signal Info
Language English
Operation
Contrast
Bright
Red
Blue
Signal Type *1
Reset
Color
Tint
Sharp
Progressive *2
Reset
Lamp Timer
Keystone
Auto Power Off
Background
Theater Mode
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
3030
3030
3030
3030
Component
RGB
3030
3030
70
2D Progressive
3D Progressive
Film Mode 1
Film Mode 2
127127
ON
OFF
Blue
None
ON
OFF
Items on the INPUT 2 (RGB) Mode Menu Bar
Sub menuSub menu
Picture
Fine Sync
Options Signal Info
Language English
Contrast
Bright
Red
Blue
Signal Type
Reset
Clock
Phase
H-Pos
V-Pos
Reset
Lamp Timer
Keystone
Auto Power Off
Background
Theater Mode
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
3030
3030
3030
3030
Component
RGB
127127
120120
5050
5050
127127
ON
OFF
Blue
None
ON
OFF
PRJ Mode
Special Modes
Front
CeilingFront
Rear
CeilingRear
640480
480P
PRJ Mode
Special Modes
Front
CeilingFront
Rear
CeilingRear
640480
480P
*1 “Signal Type does not appear when the INPUT 1 (COMPONENT) mode is selected. *2 “Progressive” only appears when receiving a 480i signal in the INPUT 2 (COMPONENT) mode.
•“Color, Tint and Sharp do not appear in the INPUT 2 (RGB) mode.
21
Page 22
Using the GUI (Graphical User Interface) Menu Screens
Items on the S-VIDEO or VIDEO Mode Menu Bar
Main menu
Picture1
Picture2
Options Signal Info
Language English
Sub menu
Contrast
Bright
Red
Blue
Reset
Color
Tint *3
Sharp
Progressive
Reset
Lamp Timer
Keystone
Auto Power Off
Background
Theater Mode
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
3030
3030
3030
3030
3030
3030
70
2D Progressive
3D Progressive
Film Mode 1
Film Mode 2
127127
ON
OFF
Blue
None
ON
OFF
Operation
PRJ Mode
Video System Auto
Front
CeilingFront
Rear
CeilingRear
PAL
NTSC3.58
SECAM
NTSC4.43
PAL M
PAL N
PAL (60Hz)
*3 “Tint” does not appear when receiving “PAL”, “SECAM”, “PAL M”, “PAL N or PAL (60Hz) in the S-VIDEO or VIDEO mode.
22
Page 23
Selecting the On-screen Display Language
Operation
Projector
Remote control
English is the preset language for the On-screen Display. The language can be set to English, German,
ON/OFF
KEYSTONE
LAMP
TEMP.
PICT MODE
POWER
INPUT
BACK ENTER MENU
2, 3
2, 4
1, 5
VOL
MUTE
BACK
ENTER
POWER
MENU
Spanish, Dutch, French, Italian, Swedish, Portuguese, Chinese, Korean or Japanese.
1 Press MENU.
2 Press /ƒ to select Language, and then press
ENTER.
3 Press /ƒ to select the desired language.
(GUI) On-screen Display
4 Press ENTER to save the setting. The On-screen
Display is now programmed to display in the language selected.
5 To exit from the GUI, press MENU.
Selecting the Video Input System Mode (S-VIDEO or VIDEO mode only)
Projector
ON/OFF
KEYSTONE
LAMP
TEMP.
PICT MODE
POWER
INPUT
BACK ENTER MENU
(GUI) On-screen Display
2, 3
2, 4
1, 5
Remote control
VOL
MUTE
POWER
BACK
MENU
ENTER
The video input system mode is preset to Auto”; however, it can be changed to a specific system mode, if the selected system mode is not compatible with the connected audiovisual equipment.
1 Press MENU.
2 Press /ƒ to select Video System, and then
press ENTER.
3 Press /ƒ to select the desired video system
mode.
4 Press ENTER to save the setting.
5 To exit from the GUI, press MENU.
When the system mode is set to Auto, you may not receive a clear picture due to signal differences. Should this occur, switch to the video system of the source signal.
23
Page 24
Picture Adjustments
Projector
ON/OFF
KEYSTONE
LAMP
TEMP.
PICT MODE
2, 3, 4
2, 3
POWER
INPUT
BACK ENTER MENU
1, 5
(GUI) On-screen Display
INPUT 1 or 2 (COMPONENT) mode
Remote control
VOL
MUTE
POWER
BACK
MENU
ENTER
Adjusting the Picture
You can adjust the projectors picture to your prefer­ences with the following picture settings.
Description of Adjustment Items
Selected item
Contrast Bright Red Blue Reset
Color Tint Sharp
•“Signal Type does not appear when the INPUT 1 (COMPONENT) mode is selected.
•“Progressive only appears when receiving a 480i signal in the INPUT 2 (COMPONENT) mode.
•“Color, Tint and Sharp do not appear in the INPUT 2 (RGB) mode.
•“Tint” does not appear when receiving “PAL”, “SECAM”, “PAL M”, “PAL N“ or “PAL (60Hz)” in the S-VIDEO or VIDEO
mode.
ƒ button button
For less contrast For less brightness For weaker red For weaker blue All image adjustment items are returned to the factory preset
settings. For less colour intensity Skin tones become purplish For less sharpness
For more contrast For more brightness For stronger red For stronger blue
For more colour intensity Skin tones become greenish For more sharpness
Operation
INPUT 2 (RGB) mode
S-VIDEO or VIDEO mode
1 Press MENU.
2 Press /ƒ to select Picture1 or Picture2 in
INPUT 1 or 2 (COMPONENT), S-VIDEO or VIDEO mode, or to select Picture in INPUT 2 (RGB) mode, and then press ENTER.
3 Press /ƒ to select a specific adjustment item,
and then press ENTER.
4 Press ∂/ƒ to move the mark of the selected
adjustment item to the desired setting.
5 To exit from the GUI, press MENU.
To reset all adjustment items, select Reset, and then press ENTER.
The adjustments can be stored separately in the INPUT 1, INPUT 2, S-VIDEO and VIDEO modes.
24
Page 25
Picture Adjustments
Operation
Projector Remote Control
ON/OFF
KEYSTONE
LAMP
TEMP.
PICT MODE
POWER
INPUT
BACK ENTER MENU
2, 3, 4
2, 3, 5
VOL
MUTE
1, 6
(GUI) On-screen Display
Projector Remote Control
BACK
ENTER
POWER
MENU
Selecting the Signal Type
This function allows you to select the input signal type (RGB or COMPONENT) for INPUT 2 port.
1 Press MENU.
2 Press /ƒ to select Picture in INPUT 2 (RGB)
mode, and then press ENTER.
3 Press ∂/ƒ to select “Signal Type, and then press
ENTER.
4 Press /ƒ to select Component or RGB.
5 Press ENTER to save the setting.
6 To exit from the GUI, press MENU.
Progressive Mode
This function allows you to select the progressive display of a video signal. The progressive display projects a smoother video image. For reducing distortion and noise, select an item in Progressive for optimum image quality.
ON/OFF
KEYSTONE
LAMP
TEMP.
PICT MODE
POWER
INPUT
BACK ENTER MENU
(GUI) On-screen Display
2, 3, 4
2, 3, 5
1, 6
VOL
MUTE
BACK
ENTER
POWER
MENU
1 Press MENU.
2 Press /ƒ to select Picture2 in S-VIDEO or
VIDEO mode, and then press ENTER.
3 Press ∂/ƒ to select “Progressive, and then press
ENTER.
4 Press ∂/ƒ to select the desired progressive
display.
5 Press ENTER to save the setting.
6 To exit from the GUI, press MENU.
Description of Progressive Modes
2D Progressive
Useful for displaying fast-moving images such as sports and action films. Mode that optimises the image in a displayed frame.
3D Progressive
Useful for displaying relatively slow-moving images such as drama and documentary more clearly. Mode that optimises the image by estimating the movement of a number of preceding and succeeding frames.
Film Mode 1
Effective for displaying action movies or other fast-moving film sources.
Film Mode 2
Effective for displaying still images or slow-moving film sources as in a documentary.
25
The film source is a digital video recording with the original encoded as is at 24 frames/second. The projector can convert this film source to progressive video at 60 frames/second to play back a high­definition image.
Page 26
Computer Image Adjustments (INPUT 2 (RGB) mode only)
Remote control
Auto Sync Adjustment
Used to automatically adjust a computer image.
Auto Sync adjustment can be made manually by
RGB/
COMPONENT
INPUT 1
S-VIDEO CLR TEMP
VIDEO FREEZE
PICT MODE
AUTO SYNCINPUT 2 GAMMA
KEYSTONE
1
pressing AUTO SYNC.
The sync adjustment is automatically made each time the projector is turned on while connected to a computer or the input selection is changed.
1 Press AUTO SYNC on the remote control.
On-screen Display During Auto Sync adjustment, Adjusting The Image
is displayed as shown on the left.
Auto Sync adjustment may take some time to complete, depending on the image of the computer connected to the projector.
When the optimum image cannot be achieved with Auto Sync adjustment, use manual adjustments. (See page 27.)
Operation
26
Page 27
Computer Image Adjustments (INPUT 2 (RGB) mode only)
Operation
Projector
ON/OFF
KEYSTONE
LAMP
TEMP.
PICT MODE
POWER
INPUT
BACK ENTER MENU
(GUI) On-screen Display
2, 3, 4
2, 3
1, 5
Remote control
VOL
MUTE
POWER
BACK
MENU
ENTER
Adjusting the Computer Image
When displaying computer patterns which are very detailed (tiling, vertical stripes, etc.), interference may occur between the LCD pixels, causing flickering, vertical stripes, or contrast irregularities in portions of the screen. Should this occur, adjust “Clock”, “Phase”, H-Pos and V-Pos for the optimum computer image.
Description of Adjustment Items
DescriptionSelected item
Clock Phase H-Pos V-Pos
Computer image adjustments can be made easily by pressing AUTO SYNC (
(Select the desired computer input mode with INPUT
on the projector or INPUT 2 on the remote control.)
1 Press MENU.
2 Press /ƒ to select Fine Sync, and then press
ENTER.
Adjusts vertical noise. Adjusts horizontal noise (similar to tracking on your VCR). Centres the on-screen image by moving it to the left or right. Centres the on-screen image by moving it up or down.
). See page 26 for details.
3 Press /ƒ to select a specific adjustment item,
and then press ENTER.
4 Press ∂/ƒ to move the mark of the selected
adjustment item to the desired setting.
5 To exit from the GUI, press MENU.
The value range of Clock setting is limited by the type of signal received.
To reset all adjustment items, select “Reset on the “Fine Sync menu screen and press ENTER.
27
Page 28
Useful Features
Freeze Function
Remote control
RGB/
COMPONENT
INPUT 1
S-VIDEO CLR TEMP
VIDEO FREEZE
PICT MODE
AUTO SYNCINPUT 2 GAMMA
KEYSTONE
On-screen Display
1, 2
This function allows you to instantly freeze a moving image. This is useful when you want to display a still image from a computer or video, giving you more time to explain the image to the audience.
1 Press FREEZE on the remote control to freeze
the image.
2 Press FREEZE again to return to the moving
image.
Useful Features
28
Page 29
Adjusting the Colour Temperature
Remote control This function can be used to adjust the colour
temperature to suit the type of image input to the projector (video, computer image, TV broadcast, etc.).
RGB/
COMPONENT
INPUT 1
S-VIDEO CLR TEMP
VIDEO FREEZE
PICT MODE
AUTO SYNCINPUT 2 GAMMA
KEYSTONE
1
Decrease the colour temperature to create warmer, reddish images for natural flesh tones. Increase the colour temperature to create cooler, bluish images for a brighter picture.
Description of Colour Temperature
12 3 4
(Red) (Blue)
Decreases colour temperature for warmer, reddish,
incandescent-like images. (Low colour temperature)
Increases colour temperature for cooler, bluish, florescent­like images.
(High colour temperature)
Position1
Position2
Position3
Useful Features
On-screen Display
s
s
1 Press CLR TEMP on the remote control. Each time
CLR TEMP is pressed, colour temperature toggles
as shown below.
1 2 34
Position4
29
s
Page 30
Gamma Correction
STANDARD
GAMMA 1
Remote control
RGB/
COMPONENT
INPUT 1
S-VIDEO CLR TEMP
VIDEO FREEZE
PICT MODE
AUTO SYNCINPUT 2 GAMMA
KEYSTONE
On-screen Display
1
• Gamma is an image quality enhancement function that offers a richer image by brightening the darker portions of the image without altering the brightness of the brighter portions.
• Three gamma settings are available to allow for differences in the images displayed and in the brightness of the room.
• When you are displaying images with frequent, dark scenes, such as a film or concert, or when you are displaying images in a bright room, this feature makes the dark scenes easier to see and gives the impres­sion of greater depth in the image.
Gamma Modes
Selected Mode
STANDARD
GAMMA 1
GAMMA 2
1 Press GAMMA on the remote control. Each time
GAMMA is pressed, the gamma level toggles as
shown on the left.
Gamma mode
For a highly defined image emphasising high contrast and colour reproduction.
For a warm and moist image controlling contrast and brightness.
Most suitable when viewing images in a brightly lit room.
GAMMA 2
Useful Features
ss
30
Page 31
Selecting the Picture Display Mode
4:3
720P, 1080i
800 600 800 600 800 600
800 600
600 450 600 450 600 450
– –
800 450 800 450 800 450 800 450
VGA, SVGA, XGA, SXGA
Projector
ON/OFF
KEYSTONE
EXAMPLE
LAMP
TEMP.
PICT MODE
Video
Computer
4:3 aspect ratio
POWER
INPUT
BACK ENTER MENU
1
4:3 aspect ratio 480I/P, NTSC, PAL, SECAM
16:9 aspect ratio, 720P, 1080i
Input Signal
Remote control This function allows you to modify or customise the
RGB/
COMPONENT
INPUT 1
S-VIDEO CLR TEMP
VIDEO FREEZE
PICT MODE
AUTO SYNCINPUT 2 GAMMA
KEYSTONE
picture display mode to enhance the input image. Depending on the input signal, you can choose the picture display mode preferred.
1 Press PICT MODE. Each time PICT MODE is
pressed, the picture mode changes as shown below.
FULL WIDE NORMAL
Letterbox
Squeeze
Output screen image
FULL WIDE NORMAL
PICT MODE
FULL
PICT MODE
WIDE
PICT MODE
NORMAL
480I/P, NTSC,
PAL,
SECAM
Useful Features
720P, 1080i
VGA,
SVGA,
XGA,
SXGA
Letterbox
Squeeze
16:9 aspect ratio
Input Signal
4:3 aspect ratio
PICT MODE
FULL
PICT MODE
FULL
Output screen image
FULL
PICT MODE
FULL
PICT MODE
WIDE
PICT MODE
WIDE
PICT MODE
WIDE
PICT MODE
NORMAL
PICT MODE
NORMAL
When inputting a VGA text mode (640⳯350) signal or an RGB signal from a device other than a computer, the display is fixed in FULL (4:3) mode, with the image filling up the whole screen.
31
Page 32
Checking the Input Signal and the Lamp Usage Time
Projector Remote control
ON/OFF
KEYSTONE
LAMP
TEMP.
PICT MODE
POWER
INPUT
BACK ENTER MENU
2
2
VOL
MUTE
1
(GUI) On-screen Display
BACK
ENTER
POWER
MENU
This function allows you to check the current input signal information and the accumulated lamp usage time.
1 Press MENU.
2 Press /ƒ to select Options, and then press
ENTER. The current input signal information and the lamp usage time will be displayed.
It is recommended that the lamp be replaced after approximately 900 hours of usage. See pages 38 and 39 for lamp replacement.
Automatic Power Shutoff Function
Projector Remote control
ON/OFF
KEYSTONE
LAMP
TEMP.
PICT MODE
POWER
INPUT
BACK ENTER MENU
2, 3, 4
2, 3
VOL
MUTE
1, 5
(GUI) On-screen Display
POWER
BACK
MENU
ENTER
When no input signal is detected for more than 15 minutes, the projector will automatically shut off.
Description of Automatic Power Shutoff
ON
OFF
1 Press MENU.
2 Press /ƒ to select Options, and then press
ENTER.
3 Press /ƒ to select Auto Power Off, and then
press ENTER.
4 Press /ƒ to select ON or OFF.
5 To exit from the GUI, press MENU.
•“Auto Power Off” is factory preset to “ON”.
•“Power OFF in 5 min.” will appear five minutes before the
power is automatically turned off.
Useful Features
Power automatically shuts off after 15 minutes without a signal being input.
Automatic Power Shutoff disabled.
32
Page 33
Selecting a Background Image
Projector Remote control
ON/OFF
KEYSTONE
LAMP
TEMP.
PICT MODE
POWER
INPUT
BACK ENTER MENU
2, 3, 4
2, 3
VOL
MUTE
1, 5
(GUI) On-screen Display
BACK
ENTER
POWER
MENU
This function allows you to select the image displayed when no signal is being sent to the projector.
Description of Background Images
Blue
None
1 Press MENU.
2 Press /ƒ to select Options, and then press
3 Press /ƒ to select Background, and then
4 Press /ƒ to select Blue or None.
5 To exit from the GUI, press MENU.
*1 While projecting the blue screen, the picture automatically
switches to FULL (4:3) mode even if another display mode has been selected.
Blue screen
Black screen
ENTER.
press ENTER.
*1
POWER
INPUT
Useful Features
BACK ENTER MENU
Theatre Mode Function
Projector Remote control
ON/OFF
KEYSTONE
LAMP
TEMP.
PICT MODE
2, 3, 4
2, 3
1, 5
(GUI) On-screen Display
VOL
MUTE
POWER
BACK
MENU
ENTER
Function with toggle switch to control the quantity of projected light. Select “ON” or “OFF” to decrease or increase brightness, power consumption and fan noise.
Description of Theatre Modes
ON
OFF
1 Press MENU.
2 Press /ƒ to select Options, and then press
3 Press /ƒ to select Theater Mode, and then
4 Press /ƒ to select ON or OFF.
5 To exit from the GUI, press MENU.
Quantity of light is 70%. Power consumption is 200 W.
Quantity of light is 100%. Power consumption is 230 W.
ENTER.
press ENTER.
33
•“Theater Mode” is factory preset to “ON” .
When selecting OFF in Theater Mode, fan noise is
increased.
Even when selecting ON in Theater Mode, fan noise may increase if internal temperature rises enough to activate the cooling function.
Page 34
Reverse/Invert Image Function
Projector Remote control
ON/OFF
KEYSTONE
LAMP
TEMP.
PICT MODE
POWER
INPUT
BACK ENTER MENU
2, 3
2, 3
VOL
MUTE
1, 4
(GUI) On-screen Display
BACK
ENTER
POWER
MENU
This projector is equipped with a reverse/invert image function which allows you to reverse or invert the pro­jected image for various applications.
Description of Projected Images
Selected item
Front
CeilingFront
Rear
CeilingRear
1 Press MENU.
2 Press /ƒ to select PRJ Mode, and then press
ENTER.
3 Press ∂/ƒ to select the desired projection mode,
and then press ENTER.
4 To exit from the GUI, press MENU.
This function is used for the reversed image and ceiling-
mount setups. See page 18 for these setups.
Projected image
Normal image
Inverted image
Reversed image
Reversed and inverted image
Special Mode Adjustment
Projector Remote control
ON/OFF
KEYSTONE
LAMP
TEMP.
PICT MODE
POWER
INPUT
BACK ENTER MENU
(GUI) On-screen Display
2, 3
2, 4
1, 5
VOL
MUTE
POWER
BACK
MENU
ENTER
Ordinarily, the type of input signal is detected and the correct resolution mode is automatically selected. However, since the projector cannot distinguish 640480 signal resolution on computers or 480P on DTVs, select an appropriate mode on Special Modes.
1 Press MENU.
2 Press /ƒ to select Special Modes, and then
press ENTER.
3 Press /ƒ to select the optimal resolution mode.
4 Press ENTER to save the setting.
5 To exit from the GUI, press MENU.
When inputting DTV 480P signals, select 480P in step 3
above.
Useful Features
34
Page 35
Air Filter Maintenance
Maintenance & Troubleshooting
Air Filter Maintenance
Right Side View
Air filter
Cleaning the air filter
Disconnect the power cord.
1
Unplug the power cord from the AC socket.
• This projector is equipped with an air filter to ensure the optimal operating condition of the projector.
• The air filter should be cleaned every 100 hours of use. Clean the filters more often when the projector is used in a dusty or smoky location.
• Have your nearest Sharp Authorised LCD Projector Dealer or Service Centre exchange the filter (PFILD0123CEZZ) when it is no longer possible to clean it.
Remove the filter cover.
2
Turn over the projector. Press the tab and remove the filter cover in the direction of the arrow.
Ta b
34
Clean the dust off the air filter and cover with a vacuum cleaner extension hose.
Maintenance &
Troubleshooting
Clean the air filter.
Replace the filter cover.
Insert the tab on the end of the filter cover into the filter cover opening and press the filter cover into position.
Ta b
35
Page 36
Air Filter Maintenance
;;;;;
;;;;;
Replacing the air filter
Disconnect the power
1 32
cord.
Unplug the power cord from the AC socket.
Replace the air filter.
4
1 Put the new air filter into position. 2 Put the air filter stopper back into position.
Remove the filter cover.
Turn over the projector. Press the tab and remove the filter cover in the direction of the arrow.
Remove the air filter.
1 Remove the air filter stopper. 2 Remove the air filter.
Ta b
Replace the filter cover.
5
Insert the tab on the end of the filter cover into the filter cover opening and press the filter cover into position.
Ta b
Be sure the filter cover is securely installed. The power will not turn on unless it is correctly installed.
Troubleshooting
Maintenance &
36
Page 37
Lamp/Maintenance Indicators
Maintenance Indicators
POWER
ON/OFF
KEYSTONE
TEMPERATURE WARNING indicator
LAMP REPLACEMENT indicator
POWER indicator
LAMP
TEMP.
The internal temperature is abnormally high.
The indicator flashes in red.
The lamp does not illuminate.
The lamp requires replacement.
red when the projector is on.
POWER indicator
LAMP REPLACEMENT
indicator
TEMPERATURE WARNING indicator
The warning lights on the projector indicate problems inside the projector.
There are two warning lights: a TEMPERATURE WARNING indicator which warns that the projector is too hot, and a LAMP REPLACEMENT indicator which lets you know when to change the lamp.
If a problem occurs, either the TEMPERATURE WARNING indicator or the LAMP REPLACEMENT indicator will illuminate red. After turning off the power, follow the procedures given below.
ProblemMaintenance Indicator Condition Possible Solution
Blocked air intake.
Clogged air filter.
Cooling fan breakdown.
Internal circuit failure.
Cooling down. Wait until the indicator stops flashing and
Burnt-out lamp.
Lamp circuit failure.
Lamp has been used for
over 900 hours.
The filter cover is open. Securely install the filter cover.The indicator flashes in
Relocate the projector to an area with proper
ventilation.
Clean the filter. (See pages 35 and 36.)
Take the projector to your nearest Sharp Authorised LCD Projector Dealer or Service Centre for repair.
turns off.
Carefully replace the lamp. (See pages 38 and 39.)
Take the projector to your nearest Sharp Authorised LCD Projector Dealer or Service Centre for repair.
If the TEMPERATURE WARNING indicator illuminates, follow the solution listed above and then wait until the projector has cooled down completely before turning the power back on. (At least 5 minutes.)
If the power is turned off and then turned on again, as during a brief rest, the LAMP REPLACEMENT indicator may be triggered, preventing the power from going on. Should this occur, remove the power cord from the wall outlet and plug it in again.
Lamp
The lamp in this projector operates for approximately 1,000 cumulative hours, depending on the usage environ­ment. It is recommended that the lamp be replaced after 900 cumulative hours of use or when you notice a significant deterioration of the picture and colour quality. The lamp usage timer can be checked with the On­screen Display. (See page 32.)
CAUTION
Intense light hazard. Do not attempt to look into the aperture and lens while the projector is operating.
As the usage environment can vary significantly, the projector lamp may not operate for 1,000 hours.
•“1,000 hours” above indicates average life span and should be used for reference only. This is different than the warranty period.
For safety, the power will not be turned on from the fourth times when turning on the power without changing the lamp after use for 1,000
Maintenance &
Troubleshooting
hours.
Condition
The LAMP REPLACEMENT indicator illuminates red, and “LAMP” will appear in yellow in the lower-left corner of the picture.
A significant deterioration of the picture and colour quality occurs.
The power will automatically turn off and the projector will enter standby mode.
LAMP will appear in red in the lower-left corner of the picture, and the power will turn off.
Problem
Lamp has been used for over 900 hours.
Lamp has been used for over 1,000 hours.
Purchase a replacement lamp unit (lamp cage/module) of the current type BQC­PGC20X//1 from your nearest Sharp Authorised LCD Projector Dealer or Service Centre.
Replace the lamp. (See pages 38 and 39.) If you wish, you may have the lamp replaced at your nearest Sharp Authorised LCD Projector Dealer or Service Centre.
Possible Solution
37
Page 38
Replacing the Projection Lamp
;;;;;
;;;;;
CAUTION:
Potential hazard of glass particles if lamp ruptures. Please have Sharp Authorised LCD Projector
Dealer or Service Centre replace lamp if rupture occurs.
Do not remove the lamp cage directly after operation of the projector. The lamp may be extremely
hot. Wait at least one hour after the power cord is disconnected to allow the surface of the lamp cage to fully cool before removing the lamp cage.
It is recommended that the lamp be replaced after approximately 900 cumulative hours of use or when you notice a significant deterioration of the picture and colour quality. Carefully change the lamp by following the steps below. If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorised LCD Projector Dealer or Service Centre for repair. Purchase a replacement lamp unit (lamp/cage module) of the current type BQC-PGC20X//1 from your nearest Sharp Authorised LCD Projector Dealer or Service Centre. Then carefully change the lamp by following the instructions below. If you wish, you may have the lamp replaced at your nearest Sharp Authorised LCD Projector Dealer or Service Centre.
Removing and installing the lamp unit
CAUTION
Be sure to remove the lamp cage by the handle. Be sure not to touch the glass surface of the lamp cage or the inside of the projector.
To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below.
Be sure to change the air filter during lamp replacement. The air filter comes packaged with the lamp unit.
First Change Filter (Steps 3-6)
Turn off the power.
1 3
Press ON/OFF on the projector or POWER on the remote control. Wait until the cooling
Disconnect the power
2
cord.
Unplug the power cord from the AC socket.
Remove the filter cover.
Turn over the projector. Press the tab and remove the filter cover in the direction of the arrow.
fan stops.
ON/OFF
Ta b
or
POWER
VOL
POWER
MUTE
BACK
MENU
Remove the air filter.
46
1 Remove the air filter stopper. 2 Remove the air filter.
Replace the air filter.
5
1 Put the new air filter into
position.
2 Put the air filter stopper back
into position.
Replace the filter cover.
Insert the tab on the end of the filter cover into the filter cover opening and press the filter cover into position.
Troubleshooting
Maintenance &
Ta b
38
Page 39
Replacing the Projection Lamp
Then Change Lamp (Steps 7-10)
Remove the lamp cage cover.
7
Remove the lamp cage.
8
Turn over the projector and loosen the user service screw that secures the lamp cage cover. Then lift open the cover in the direction of the arrow.
Insert the new lamp cage.
Loosen the securing screws on the lamp cage. Hold the lamp cage by the handle and pull it towards you.
Attach the lamp cage cover.
910
Press the lamp cage firmly into the lamp cage compartment. Fasten the securing screws.
Slide the lamp cage cover in the direction of the arrow. Then tighten the user service screw.
Resetting the lamp timer
Connect the power
1
cord.
Plug the power cord into the AC socket of the projector.
Maintenance &
Troubleshooting
Reset the lamp timer only after replacing the lamp.
Reset the lamp timer.
2
1 Press KEYSTONE and
KEYSTONE ƒ on the projector at
the same time.
2 Press INPUT and PICT MODE on
the projector at the same time.
3 Press PICT MODE and MENU on
the projector at the same time.
1
INPUT
BACK ENTER MENU
PICT MODE
32
LAMP 0000H is displayed, indicating that the lamp timer is reset.
39
Page 40
Using the Kensington Lock
This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with the
Kensington Security Standard connector
system for instructions on how to use it to secure the projector.
Troubleshooting
Problem
No picture and no sound.
Sound is heard but no picture appears.
Colour is faded or poor.
Picture is blurred.
Picture appears but no sound is heard.
An unusual sound is occasionally heard from the cabinet.
Maintenance indicator illuminates.
Picture noise appears.
480P images do not appear. Colour is distorted (INPUT 2 mode
only).
Check
Projector power cord is not plugged into the wall outlet.
The filter cover is not securely installed.
Selected input is wrong. (See page 16.)
Cables incorrectly connected to side and rear panels of the projector. (See pages 11–14.)
Remote control batteries have run down. (See page 8.)
Cables incorrectly connected to side and rear panels of the projector. (See pages 11–14.)
•“Contrast” and “Bright” adjustments are set to minimum position. (See page 24.)
•“Color” and “Tint” adjustments are not correct. (See page 24.)
Adjust the focus. (See page 15.)
Projection distance is too long or too short to allow for proper focus. (See page 17.)
Cables incorrectly connected to side and rear panels of the projector. (See pages 11–14.)
Volume is set to minimum. (See page 16.)
If the picture is normal, the sound is due to cabinet shrinkage caused by temperature changes.
This will not affect operation or performance.
Refer to Lamp/Maintenance Indicators on page 37.
Adjust the Phase setting. (See page 27.)
Set the resolution mode to 480P. (See page 34.)
Change the input signal type. (See page 25.)
Troubleshooting
Maintenance &
40
Page 41
Appendix
Attaching the Lens Cap
Put on the lens cap to prevent damage to the lens when transporting the projector. A lens cap strap is provided to prevent the loss of the lens cap.
Attach the lens cap
1
strap to the lens cap.
CAUTION
• Do not lift or carry the projector by the lens or the lens cap as this may damage the lens.
You can also use the end of a mechanical pencil or other pointed object to feed the lens cap strap through the openings.
Attach the lens cap
2
strap to the projector.
Attach the lens cap to
3
the projector with the lens cap eyelet facing up.
Appendix
41
Page 42
Connection Pin Assignments
INPUT 2 Port: 15-pin mini D-sub female connector
Computer Input
Analog
1. Video input (red)
2. Video input (green/sync on green)
5
10 15
1 6 11
RS-232C Port: 9-pin D-sub male connector of the DIN-D-sub RS-232C cable
Pin No. Signal Name I/O Reference
1
5
9
6
1 Not connected 2 RD Receive Data Input Connected to internal circuit 3 SD Send Data Output Connected to internal circuit 4 Not connected 5 SG Signal Ground Connected to internal circuit 6 Not connected 7 Not connected 8 Not connected 9 Not connected
3. Video input (blue)
4. Not connected
5. Composite sync
6. GND (red)
7. GND (green/sync on green)
8. GND (blue)
9. Not connected
10. Not connected
11. GND
12. Bi-directional data
13. Horizontal sync signal
14. Vertical sync signal
15. Data clock
RS-232C Terminal: 9-pin Mini DIN female connector
8
9
7
6
5
4
21
Pin No. Signal Name I/O Reference
1 Not connected 2 RD Receive Data Input Connected to internal circuit 3 SD Send Data Output Connected to internal circuit 4 Not connected
3
5 SG Signal Ground Connected to internal circuit 6 Not connected 7 Not connected 8 Not connected 9 Not connected
Appendix
42
Page 43
RS-232C Port Specifications
PC control
A computer can be used to control the projector by connecting an RS-232C cable (null modem, cross type, sold separately) to the projector. (See page 14 for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table. Signal format: Conforms to RS-232C standard. Baud rate: 9,600 bps Data length: 8 bits Parity bit: NON Stop bit: 1 bit Flow control: None
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After the projector processes the command from the computer, it sends a response code to the computer.
Command format
C1 C2 C3 C4 P1 P2 P3 P4
Command 4-digits Parameter 4-digits
Return code (0DH)
Response code format
Normal response
O K
Problem response (Failure due to incorrect command/parameter or the other communication errors)
E R R
When more than one code is being sent, send each command only after the OK response code for the previous command from the projector is verified.
When using the computer control function of the projector, the projector operating status cannot be read to the computer. Therefore, confirm the status by transmitting the display commands for each adjustment menu and checking the status with the On-screen Display. If the projector receives a command other than a menu display command, it will execute the com­mand without displaying the On-screen Display.
Return code (0DH)
Return code (0DH)
Appendix
43
Page 44
RS-232C Port Specifications
Commands
EXAMPLE
When BRIGHT of RGB IMAGE ADJUSTMENT is set to 10.
ProjectorComputer
RABR 1 0_ OK
→ ←
CONTROL ITEM
AUTO POWER OFF
POWER SETTING
INPUT SWITCHING
INPUT CHECK
KEYSTONE ADJUSTMENT
LANGUAGE SELECTION
VIDEO SYSTEM SELECTION
S-VIDEO/VIDEO IMAGE ADJUSTMENT 1
S-VIDEO/VIDEO IMAGE ADJUSTMENT 2
S-VIDEO/VIDEO COLOR TEMPERATURE ADJUSTMENT
COMPONENT IMAGE ADJUSTMENT 1
COMMAND
C2 C3 C4 P1 P2 P3 P4
C1
P
A
P
A
O
P
O
P
V
I
V
I
R
I
R
I
C
I
EKYS***
E
M
E
M
E
M
E
M
E
M
E
M
E
M
E
M
E
M
E
M
E
M
E
M
E
M
E
M
E
M
E
M
E
M
E
M
E
M
A
V
A
V
A
V
A
V
A
V
A
V
A
V
A
V
A
V
AVCT___
A
R
A
R
A
R
A
R
A
R
PARAMETER
O
O
W
W
E
E
G
G
H
L
L
L
L
L
L
L
L
L
L
L
S
S
S
S
S
S
S
S
P
B
R
B
R
C
T
S
R
P
B
R
B
R
_
_
W
_
_
W
_
_
R
_
_
R
_
_
D
_
_
D
_
_
B
_
_
B
_
_
K
_
_
A
_
_
A
_
_
A
_
_
A
_
_
A
_
_
A
_
_
A
_
_
A
_
_
A
_
_
A
_
_
A
_
_
Y
_
_
Y
_
_
Y
_
_
Y
_
_
Y
_
_
Y
_
_
Y
_
_
Y
*
_
I
*
_
R
*
_
D
*
_
E
_
_
E
*
_
O
*
_
I
_
_
H
_
_
E
*
_
I
*
_
R
*
_
D
*
_
E
_
_
E
AUTO POWER OFF (OFF)
0
_
AUTO POWER OFF (ON)
1
_
POWER OFF (STANDBY)
0
_
POWER ON
1
_
S-VIDEO
1
_
VIDEO
2
_
INPUT1
1
_
INPUT2
2
_
INPUT CHECK
0
_
KEYSTONE
*
(127 – 127)
ENGLISH
1
_
DEUTSCH
2
_
ESPAÑOL
3
_
NEDERLANDS
4
_
FRANÇAIS
5
_
ITALIANO
6
_
SVENSKA
7
_
PORTUGUÊS
8
_
9
_
0
1
1
1
AUTO
1
_
PAL
2
_
NTSC 3.58
3
_
SECAM
4
_
NTSC 4.43
5
_
PAL (M)
6
_
PAL (N)
7
_
PAL (60 Hz)
8
_
CONTRAST (30 – 30)
*
*
BRIGHT (30 – 30)
*
*
RED (30 – 30)
*
*
BLUE (30 – 30)
*
*
RESET
1
_
COLOR (30 – 30)
*
*
TINT (30 – 30)
*
*
SHARPNESS (0 – 7)
*
_
RESET
2
_
COLOR TEMPERATURE
*
(1– 4)
CONTRAST (30 – 30)
*
*
BRIGHT (30 – 30)
*
*
RED (30 – 30)
*
*
BLUE (30 – 30)
*
*
RESET
1
_
CONTROL
CONTENTS
CONTROL ITEM
COMPONENT IMAGE ADJUSTMENT 2
COMPONENT COLOR TEMPERATURE ADJUSTMENT
RGB IMAGE ADJUSTMENT
RGB COLOR TEMPERATURE ADJUSTMENT
BACKGROUND SELECTION
VOLUME ADJUSTMENT
SCREEN SETTING
INPUT2 SIGNAL TYPE SELECTION
INPUT1 PICTURE MODE
INPUT2 PICTURE MODE
S-VIDEO/ VIDEO PICTURE MODE
INPUT1/ S-VIDEO/VIDEO GAMMA SELECTION
INPUT2 GAMMA SELECTION
INPUT AUTO SYNCHRONIZATION
COMMAND
C2 C3 C4 P1 P2 P3 P4
C1
A
R
A
R
A
R
A
R
ARCT___
B
R
B
R
B
R
B
R
B
R
BRCT___
M
I
M
I
O
V
U
M
U
M
M
I
M
I
M
I
M
I
M
I
M
I
M
I
M
I
B
I
B
I
A
R
A
R
A
R
B
R
B
R
B
R
A
R
A
R
A
R
A
G
A
G
A
G
A
G
A
G
A
G
DAJS___
PARAMETER
C
T
S
R
P
B
R
B
R
B
B
L
T
T
R
R
I
I
I
I
I
I
S
S
S
S
S
S
S
S
S
S
S
M
M
M
M
M
M
*
_
O
*
_
I
_
_
H
_
_
E
*
_
I
*
_
R
*
_
D
*
_
E
_
_
E
_
_
G
_
_
G
_
_
A
_
_
E
_
_
E
_
_
E
_
_
E
_
_
N
_
_
N
_
_
P
_
_
P
_
_
P
_
_
P
_
_
I
_
_
I
_
_
R
_
_
R
_
_
R
_
_
R
_
_
R
_
_
R
_
_
V
_
_
V
_
_
V
_
_
V
_
_
V
_
_
V
_
_
R
_
_
R
_
_
R
COLOR (30 – 30)
*
*
TINT (30 – 30)
*
*
SHARPNESS (0 – 7)
*
_
RESET
2
_
COLOR TEMPERATURE
*
(1 – 4)
CONTRAST (30 – 30)
*
*
BRIGHT (30 – 30)
*
*
RED (30 – 30)
*
*
BLUE (30 – 30)
*
*
RESET
1
_
COLOR TEMPERATURE
*
(1 – 4)
BLUE
3
_
NONE
4
_
VOLUME (00 – 60)
*
*
MUTE ON
1
_
MUTE OFF
0
_
REVERSE OFF
0
_
REVERSE ON
1
_
INVERT OFF
0
_
INVERT ON
1
_
2D PROGRESSIVE
0
_
3D PROGRESSIVE
1
_
FILM MODE1
2
_
FILM MODE2
3
_
RGB
1
_
COMPONENT
2
_
FULL
1
_
WIDE
2
_
NORMAL
3
_
FULL
1
_
WIDE
2
_
NORMAL
3
_
FULL
1
_
WIDE
2
_
NORMAL
3
_
STANDARD
1
_
GAMMA1
2
_
GAMMA2
3
_
STANDARD
1
_
GAMMA1
2
_
GAMMA2
3
_
1
AUTO SYNC START
CONTROL
CONTENTS
Appendix
If an underbar (_) appears in the parameter column, enter a space. If an asterisk (*) appears, enter a value in the range indicated in brackets under CONTROL CONTENTS.
44
Page 45
Computer Compatibility Chart
Horizontal Frequency: 15–80 kHz Vertical Frequency: 43–85 Hz Pixel Clock: 12–108 MHz Compatible with sync on green and composite sync signals SXGA (1,280 1,024) compatible in intelligent compression
PC/
MAC/
WS
PC
VGA
SVGA
XGA
Resolution
640 350
720 350
640 400
720 400
640 480
800 600
1,024 768
Horizontal
Frequency
(kHz)
27.0 60
31.5 70
37.9 85
27.0 60
31.5 70
27.0 60
31.5 70
37.9
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
31.3 50
35.1 56
37.9 60
44.5 70
48.1 72
46.9 75
53.7 85
35.5 43
40.3 50
48.4 60
56.5 70
60.0 75
68.7 85
Vertical
Frequency
(Hz)
85 60 70 85 50 60
70 72 75 85
VESA
Standard
Display
Upscale
True
Intelligent
Compression
MAC 13"
MAC 19" MAC 16" MAC 21"
PC/
MAC/
WS
PC
PC/
PC/
Horizontal
Resolution Display
1,152 864
SXGA
1,152 882
1,280 1,024
640 480
VGA
XGA
1,024 768
832 624
SVGA
1,152 870
SXGA
Frequency
(kHz)
55.0 60
66.2 70
67.5 75
54.8 60
65.9 72
64.0 60
35.0
48.4 60
60.0
49.7 75
68.7
Vertical
Frequency
(Hz)
67
75
75
VESA
Standard
Intelligent
Compression
Upscale
Intelligent
Compression
This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this occur, turn off the LCD display on the notebook computer and output the display data in CRT only mode. Details on how to change display modes can be found in your notebook computers operation manual.
This projector can receive 640 350 VESA format VGA signals, however, 640 400 will appear on the screen.
The image from Mac 16 (832 624) cannot be displayed in FULL mode.
Appendix
45
Page 46
Specifications
Product type
Model
Video system
Display method
LCD panel
Lens
Projection lamp
Contrast ratio
Video input signal
S-video input signal
Component input signal
Horizontal resolution
Audio output
Computer RGB input signal
Pixel clock
Vertical frequency
Horizontal frequency
Computer control signal
Speaker system
Rated voltage
Input current
Rated frequency
Power consumption
Operating temperature
Storage temperature
Cabinet
I/R carrier frequency
Dimensions (approx.)
Weight (approx.)
Supplied accessories
Replacement parts
LCD Projector XV-Z7000E PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43/DTV 480P/DTV 720P/DTV 1080I LCD panel 3, RGB optical shutter method Panel size: 22.9 mm (0.9) (13.9 [H] 18.5 [W] mm) Display method: Translucent TN liquid crystal panel Drive method: TFT (Thin Film Transistor) Active Matrix panel No. of dots: 480,000 dots (800 [H] 600 [V]) 1–1.2 zoom lens, F2.3–2.6, f 36.0–43.2 mm DC 150 W lamp 350:1 RCA Connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 terminated RCA Connector: AUDIO, 0.5 Vrms more than 22 k (stereo) 4-pin Mini DIN connector Y (luminance signal): 1.0 Vp-p, sync negative, 75 terminated C (chrominance signal): Burst 0.286 Vp-p, 75 terminated RCA Connector (INPUT 1 terminals) Y: 1.0 Vp-p, sync negative, 75 terminated
B: 0.7 Vp-p, 75 terminated
C C
R: 0.7 Vp-p, 75 terminated
520 TV lines (DTV 720P input)
1.0 W (monaural)
PIN MINI D-SUB CONNECTOR (INPUT 2 port):
15-
RGB separate/composite sync/sync on green type analog input: 0–0.7 Vp-p, positive, 75 terminated
STEREO MINIJACK: AUDIO, 0.5 Vrms, more than 22 k (stereo)
ORIZONTAL SYNC. SIGNAL: TTL level (positive/negative) or composite sync (Apple only)
H
ERTICAL SYNC. SIGNAL: Same as above
V 12–108 MHz 43–85 Hz 15–80 kHz 9-pin Mini DIN female connector (RS-232C port)
2.8 cm (1
7
64) round
AC 100–240 V
2.6 A 50/60 Hz 230 W (Selecting OFF in the Theater Mode.) 200 W (Selecting ON in the Theater Mode.)
5°C to 35°C20°C to 60°C
Plastic 38 kHz 260 74 207 mm (W H D) (main body only) 260 82 207 mm (W H D) (including adjustment feet and projecting parts)
2.6 kg Remote control, Two AAA size batteries, Rubber leg tips for remote control, Power cord (1.8 m), Computer RGB cable (for Europe only), DIN-D-sub RS-232C cable (15 cm), A/V cable, 21 pin RCA conversion adaptor (for Europe only), Extra air filter, Lens cap (attached), Lens cap strap, Two LCD projector operation manuals Lamp unit (Lamp/cage module) (BQC-PGC20X//1), Remote control (RRMCG1643CESA), AAA size batteries, Rubber leg tips for remote control (GLEGG9095CEZZ), Power cord, Computer RGB cable (QCNWG0002CEZZ), DIN-D-sub RS-232C cable (QCNW­5288CEZZ), A/V cable (QCNW-3740CEZZ), 21 pin RCA conversion adaptor (QSOCZ0361CEZZ), Air filter (PFILD0123CEZZ), Lens cap (PCOVZ1095CEKA), Lens cap strap (UBNDT0013CEZZ), Two LCD projector operation manuals (TINS-7348CEZZ, TINS­7385CEZZ)
This SHARP projector uses LCD (Liquid Crystal Display) panels. These very sophisticated panels contain 480,000 pixels ( RGB) TFTs (Thin Film Transistors). As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to.
Specifications are subject to change without notice.
This unit has some inactive TFTs within acceptable tolerances which may result in illuminated or inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit.
Appendix
46
Page 47
Dimensions
100-240V
Rear View
Top View
RGB /COMPONENTCRCBY
(INPUT 1, 2) AUDIO INPUT
RS-232C
INPUT 1 INPUT 2/COMPONENT
Side View
TEMP.
LAMP
PICT MODE
260
KEYSTONE
ON/OFF
ZOOM
FOCUS
BACK ENTER MENU
INPUT
POWER
207
Front View
82
42 32
58118
8
LR
AUDIO INPUT
(S-VIDEO, VIDEO INPUT)
VIDEO
INPUT
S-VIDEO
INPUT
169.5
Appendix
47
Bottom View
Units: mm
Page 48
Glossary
Active digital keystone correction
Corrects keystone distortion caused when the projected image is not perpendicular to the screen. This method provides not only horizontal correction, but vertical as well, thus maintaining the original 4:3 aspect ratio and eliminating jag lines.
Aspect ratio
Width and height ratio of an image. The normal aspect ratio of a computer and video image is 4 : 3. There are also wide images with an aspect ratio of 16 : 9 and 21 : 9.
Auto sync
Optimises projected computer images by automatically adjusting certain characteristics.
Background
Initial setting image projected when no signal is being input.
Clock
Clock adjustment is used to adjust vertical noise when clock level is incorrect.
Colour temperature
Function that can be used to adjust the colour temperature to suit the type of image input to the projector.
Freeze
Function to freeze a moving image.
Gamma correction
Offers richer image viewing with dark scene phase and contrast correction according to image and room brightness. Three gamma settings are available.
GUI
Graphical User Interface. User interface with graphics that allow easier operation.
Intelligent compression and expansion
High quality resizing of lower and higher resolution images to fit the projector’s native resolution.
Phase
Phase shift is a timing shift between isomorphic signals with the same resolution. When phase level is incorrect, the projected image typically displays horizontal flicker.
Picture display mode
Allows you to modify or customise the picture display mode to enhance the input image.
Progressive mode (Film mode)
Optimises the image by converting the interlaced signal to the progressive. Useful for displaying slow-moving images or still images.
RS-232C
Function to control the projector from the computer by using the RS-232C ports on the projector and computer.
Sync on green
Video signal mode of a computer which overlaps horizontal and vertical sync signal to green colour signal pin.
Theatre mode function
Function with toggle switch to control the quantity of projected light. Select ON or OFF to decrease or increase brightness, power consumption and fan noise.
Appendix
48
Loading...