Sharp XV-Z3000 User Manual

XV-Z3000
ENGLISH DEUTSCH FRANÇAIS
PROJECTOR PROJEKTOR PROJECTEUR PROJEKTOR PROYECTOR PROIETTORE PROJECTOR
OPERATION MANUAL BEDIENUNGSANLEITUNG MODE D’EMPLOI BRUKSANVISNING MANUAL DE MANEJO MANUALE DI ISTRUZIONI GEBRUIKSAANWIJZING
SVENSKA ESPAÑOL ITALIANO
NEDERLANDS
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporat­ing a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked face of the plug, must be used. Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immedi­ately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow : Earth Blue : Neutral
Brown : Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:
or and of the same rating as above, which is also indicated on the pin
The wire which is coloured green-and-yellow must be connected to the terminal in the
plug which is marked by the letter E or by the safety earth symbol green-and-yellow.
or coloured green or
The wire which is coloured blue must be connected to the terminal which is marked with
the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with
the letter L or coloured red.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
Before using the projector, please read this operation manual carefully.
Introduction
IMPORTANT
• For your assistance in reporting the loss or theft of your Projector, please record the Serial Number located on the bottom of the projector and retain this information.
• Before recycling the packaging, please ensure that you have checked the con­tents of the carton thoroughly against the list of “Supplied accessories” on page 10.
WARNING: High brightness light source. Do not stare into the beam of light, or view
directly. Be especially careful that children do not stare directly into the beam of light.
WARNING: To reduce the risk of fire or electric shock, do not expose
this product to rain or moisture.
Model No.: XV-Z3000
Serial No.:
ENGLISH
See bottom of projector.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
DO NOT REMOVE COVER.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead sym­bol, within an equilateral triangle, is in­tended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk or electric shock to persons.
The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
1
WARNING:
The cooling fan in this projector continues to run for about 90 seconds after the projector enters standby mode. During normal operation, when putting the projector into standby mode always use the STANDBY/ON button on the projector or the STANDBY button on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord. DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
PRODUCT DISPOSAL
This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or, if you are located in the United States of America, the Electronic Industries Alliance: www.eiae.org .
Caution Concerning Lamp Replacement
See “Replacing the Lamp” on page 54.
This SHARP projector uses a DMD panel. This very sophisticated panel contains 983,040 pixels (micromirrors). As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to. This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit.
2

How to Read this Operation Manual

The specifications are slightly different, depending on the model. However, you can connect and
operate all models in the same manner.
In this operation manual, the illustration and the screen display are simplified for explanation, and
may differ slightly from the actual display.
Using the Menu Screen
ENTER button
Adjustment buttons (P/R/O/Q)
MENU button
Menu Selections (Adjustments)
Example: Adjusting “Bright”.
This operation can also be performed by using the buttons on the projector.
Press dMENU.
1
The Picture menu screen for the se­lected input mode is displayed.
Press Q or O to select the menu
2
icon to adjust.
The selected icon is highlighted.
Menu icon Menu screen
Note
The Fine Sync menu is not available for INPUT 3 or INPUT 4.
Picture
Fine Sync
Options1
Options2
Example: Picture screen menu for INPUT 1 mode
Picture INPUT 1
Picture Mode Contrast 0 Bright Color Tint Sharp Red Blue
SEL./ADJ. RETURN
Adjustment buttons (P/R/O/Q)
Press eRETURN to re-
turn to the previous screen when the menu is displayed.
Selected input mode
Menu icons
0 0 0 0 0 0
ENTER END
MENU button
ENTER button
RETURN button
Standard
Features
41
Buttons used in this operation
Button used in this step
Useful
On-screen display

Introduction

Info
........Indicates safeguards for using the projector.
.........Indicates additional information for setting up and operating the
Note
projector.
For Future Reference
PP. 60 and 61
IndexMaintenance Troubleshooting
P. 64P. 51
3

Contents

Preparing
Introduction
How to Read this Operation Manual .... 3
Contents ............................................... 4
IMPORTANT SAFEGUARDS ............... 6
Accessories ........................................ 10
Part Names and Functions ................. 11
Inserting the Batteries .......................... 14
Usable Range ...................................... 15
Quick Start
Quick Start .......................................... 16
Using
Basic Operation
Turning the Projector On/Off .............. 28
Connecting the Power Cord ................ 28
Turning the Projector on ....................... 28
Turning the Power off (Putting the
Projector into Standby Mode) ........... 29
Image Projection ................................. 29
Switching the Input Mode .................... 29
Adjusting the Projected Image ............ 30
Correcting Trapezoidal Distortion ........ 32
Resize Mode ......................................... 36
Useful Features
Operating with the Remote Control .... 38
Shifting the Projected Image Vertically
(Image Shift) ...................................... 38
Switching the Iris Setting ..................... 38
Freezing a Moving Image .................... 38
Selecting the Picture Mode .................. 38
Menu Items ......................................... 39
Using the Menu Screen ...................... 41
Menu Selections (Adjustments) ........... 41
Picture Adjustment (“Picture” menu) .. 43
Selecting the Picture Mode .................. 43
Adjusting the Image ............................. 43
Adjusting the Color Temperature ......... 44
Adjusting the Colors ............................. 44
Progressive ........................................... 44
Setup
Setting up the Projector ...................... 18
Setting up the Projector ....................... 18
Standard Setup (Front Projection) ....... 18
Ceiling-mount Setup ............................ 18
Projection (PRJ) Mode ......................... 19
Picture (Screen) Size and Projection
Distance ............................................. 20
Connections
Samples of Cables for Connection..... 22
Connecting to Video Equipment ......... 23
Connecting to a Computer ................. 26
Controlling the Projector by a
Computer .......................................... 27
Reducing Image Noise (DNR) ............. 45
Switching the Iris Setting ..................... 45
Lamp Setting ........................................ 45
Computer Image Adjustment
(“Fine Sync” menu)........................... 46
Adjusting the Computer Image ........... 46
Special Modes Setting ......................... 46
Auto Sync (Auto Sync Adjustment) ..... 46
Checking the Input Signal ................... 46
Using the “Options” Menu................... 47
Adjusting the Image Position ............... 47
Adjusting the Overscan ....................... 47
Adjusting the Vertical Size of the Display
(Subtitle Setting) ................................ 47
Setting On-screen Display ................... 48
Setting the Video System ..................... 48
Signal Type Setting .............................. 48
Selecting the HDMI Setting .................. 48
Selecting the Background Image ........ 48
Auto Power Off Function ...................... 49
Checking the Lamp Life Status ........... 49
Reversing/Inverting Projected
Images ............................................... 49
Selecting the Transmission Speed
(RS-232C) .......................................... 50
Reducing the Power Consumption When
the Power Is in Standby Mode .......... 50
Fan Mode Setting ................................. 50
Returning to the Default Settings ......... 50
Selecting the On-screen Display
Language ........................................... 50
4
Reference
Introduction
Appendix
Maintenance ....................................... 51
Maintenance Indicators ...................... 52
Regarding the Lamp ........................... 54
Lamp ..................................................... 54
Caution Concerning the Lamp ............ 54
Replacing the Lamp ............................. 54
Removing and Installing
the Lamp Unit .................................... 55
Resetting the Lamp Timer .................... 56
Connecting Pin Assignments ............. 57
RS-232C Specifications and Command
Settings ............................................ 58
Computer Compatibility Chart ............ 59
Troubleshooting .................................. 60
Specifications ..................................... 62
Dimensions ......................................... 63
Index ................................................... 64
5

IMPORTANT SAFEGUARDS

CAUTION: Please read all of these instructions before you operate this product
and save these instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing.
1. Read Instructions
All the safety and operating instructions should be read before the product is operated.
2. Retain Instructions
The safety and operating instructions should be retained for future reference.
3. Heed Warnings
All warnings on the product and in the operating instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.
8. Accessories
Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
9. Transportation
A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
11. Power Sources
This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
12. Grounding or Polarization
This product is provided with one of the following types of plugs. If the plug should fail to fit into the power outlet, please contact your electrician. Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug. b. Three-wire grounding type (mains) plug with
a grounding terminal. This plug will only fit into a grounding type power outlet.
13. Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
14. Lightning
For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the product due to lightning and power-line surges.
6
Introduction
15. Overloading
Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
17. Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power-supply cord or plug is
damaged.
b. If liquid has been spilled, or objects have fallen
into the product.
c. If the product has been exposed to rain or
water.
d. If the product does not operate normally by
following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.
e. If the product has been dropped or damaged
in any way.
f. When the product exhibits a distinct change
in performance, this indicates a need for service.
19. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
20. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
21. Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling only as recommended by the manufacturer.
22. Heat
This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
• DLP\ (Digital Light Processing), DMD\ (Digital Micromirror Device) and BrilliantColor™
are trademarks of Texas Instruments, Inc.
• Microsoft
®
and Windows® are registered trademarks of Microsoft Corporation in the United
States and/or other countries.
• PC/AT is a registered trademark of International Business Machines Corporation in the United States.
• Macintosh
®
is a registered trademark of Apple Computer, Inc. in the United States and/or
other countries.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or regis­tered trademarks of HDMI Licensing LLC.
• All other company or product names are trademarks or registered trademarks of their respective companies.
• Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or discompile the contents thereof.
7
Observe the following safeguards when setting up your projector.
Caution concerning the lamp unit
Potential hazard of glass par­ticles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Autho­rized Projector Dealer or Ser­vice Center for replacement. See “Replacing the Lamp” on page 54.
Caution concerning the setup of the pro­jector
For minimal servicing and to maintain high image quality, SHARP recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environments, the vents and lens must be cleaned more of­ten. As long as the projector is regularly cleaned, use in these environments will not reduce the overall operation life of the unit. Internal cleaning should only be performed by a Sharp Authorized Projector Dealer or Service Center.
Do not set up the projector in places ex­posed to direct sunlight or bright light.
Position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.
Caution regarding placing of the projec­tor
Place the projector on a level site within the adjustment range (8 degrees) of the adjust-
ment foot.
After the projector is purchased, a faint smell from the vent may appear when the power is first turned on. This is normal and is not a malfunction. It will disappear after the projec­tor is used for a while.
When using the projector in high-altitude areas such as mountains (at altitudes of approximately 4,900 feet (1,500 meters) or more)
When you use the projector in high-altitude areas with thin air, set “Fan Mode” to “High”. Neglecting this can affect the longevity of the optical system.
Warning about placing the projector in a high position
When placing the projector in a high position, ensure that it is secured carefully to avoid per­sonal injury caused by the projector falling down.
Do not subject the projector to hard im­pact and/or vibration.
Protect the lens so as not to hit or damage the surface of the lens.
Rest your eyes occasionally.
Continuously watching the screen for long hours will cause eye strain. Be sure to occa­sionally rest your eyes.
Avoid locations with extremes of tem­perature.
The operating temperature of the projector is from 41°F to 95°F (+5°C to +35°C).
The storage temperature of the projector is from –4°F to 140°F (–20°C to +60°C).
Do not block the exhaust and intake vents.
Allow at least 11 13/16 inches (30 cm) of space between the exhaust vent and the nearest wall or obstruction.
Be sure that the intake vent and the exhaust vent are not obstructed.
If the cooling fan becomes obstructed, a pro­tection circuit will automatically put the pro­jector into standby mode to prevent overheat damage. This does not indicate a malfunc­tion. (See pages 52 and 53.) Remove the pro­jector power cord from the wall outlet and wait at least 10 minutes. Place the projector where the intake and exhaust vents are not blocked, plug the power cord back in and turn on the projector. This will return the projector to the normal operating condition.
8
When turning off the projector, the cooling fan runs to decrease the internal temperature for a while. Unplug the power cord after the cool­ing fan stops. The period the cooling fan runs will vary, depending on the circumstances and the internal temperature.
Caution regarding usage of the projector
When using the projector, be sure not to sub­ject it to hard impact and/or vibration, as this can result in damage. Take extra care with the lens. Before moving the projector, be sure to unplug the power cord from the wall outlet, and disconnect any other cables connected to it.
Do not carry the projector by holding the lens.
When storing the projector, re-attach the lens
cap. (See page 11).
Do not expose the projector to direct sunlight or place next to heat sources. Doing so may affect the cabinet color or cause deformation of the plastic cover.
Other connected equipment
When connecting a computer or other audio­visual equipment to the projector, make the connections AFTER unplugging the power cord of the projector from the AC outlet and turning off the equipment to be connected.
Please read the operation manuals of the pro­jector and the equipment to be connected for instructions on how to make the connections.
Using the projector in other countries
The power supply voltage and the shape of the plug may vary depending on the region or country you are using the projector in. When using the projector overseas, be sure to use an appropriate power cord for the coun­try you are in.
Temperature monitor function
If the projector starts to overheat due to setup problems or blockage of the air vents, “ ” and “ ” will illuminate in the lower left corner of the picture. If the temperature continues to rise, the lamp will turn off, the temperature warn­ing indicator on the projector will blink, and after a 90-second cooling-off period the projector will enter standby mode. Refer to “Maintenance In­dicators” on page 52 for details.
Info
The cooling fan regulates the internal tem­perature, and its performance is automatically controlled. The sound of the fan may change during projector operation due to changes in the fan speed. This does not indicate malfunc­tion.
Do not unplug the power cord during projec­tion or cooling fan operation. This can cause damage due to rise in internal temperature, as the cooling fan also stops.
Introduction
9

Accessories

Supplied accessories
Remote control
RRMCGA444WJSB
21 pin RCA
conversion adaptor
QSOCZ0361CEZZ
Power cord*
(1) (2) (3)
For Europe, except U.K.
(6' (1.8 m))
QACCVA011WJPZ
* Use the power cord that corresponds to the wall outlet in your country.
Two R-03 batteries
(“AAA” size, UM/SUM-4,
HP-16 or similar)
Video cable
QCNWGA001WJZZ
For U.K. and
Singapore
(6' (1.8 m))
QACCBA036WJPZ
• Operation manual
Optional accessories
Lamp unit
DIN-D-sub RS-232C adaptor (5
57
/64o (15 cm))
AN-100LP
AN-A1RS
Lens cap (attached)
CCAPHA024WJSA
For Australia, New
Zealand and Oceania
(6' (1.8 m))
QACCLA018WJPZ
3 RCA to 15-pin D-sub cable (10' (3.0 m))
Note
• Some of the optional accessories may not be available depending on the region. Please check with your nearest Sharp Authorized Projector Dealer or Service Center.
AN-C3CP2
10

Part Names and Functions

Numbers in Z refer to the main pages in this operation manual where the topic is explained.
Projector
Top View
Power indicator
28, 5228, 52
Lamp indicator
Introduction
STANDBY/ON button
For turning the power on and putting the projector into standby mode.
ENTER button
For setting items selected or adjusted on the menu.
RESIZE button
For switching the screen size.
Front View
Focus ring
For adjusting the focus.
HEIGHT ADJUST lever
30
30
28
41
36
Temperature warning
52
indicator
INPUT buttons (P/R)
29
For switching input mode 1, 2, 3, 4, 5 or 6.
MENU button
41
For displaying adjustment and setting screens.
Adjustment buttons
41
(P/R/O/Q)
For selecting menu items.
Intake vent
51
Zoom ring
30
For enlarging/ reducing the picture.
Remote control
15
sensor (front)
Push both sides of the lens cap to attach or remove.
11
Part Names and Functions (Continued)
Numbers in Z refer to the main pages in this operation manual where the topic is explained.
Rear View
Exhaust vent
51
Intake vent
AC socket
Connect the supplied Power cord.
Rear adjustment foot
51
28
31
Terminals
65 4 1 23 7
Terminal Description
INPUT 1, 2 terminal
1
Connecting video equipment with component output terminal (DVD player, DTV decoder, DVD recorder with hard disc, etc.).
INPUT 3 terminal
Connecting video equipment with S-video output terminal (VCR, DVD
2
player, etc.).
INPUT 4 terminal
3
Connecting video equipment without S-video output terminal.
INPUT 5 terminal
4
5
6
7
Connecting video equipment with component output terminal (DVD player, DTV decoder, DVD recorder with hard disc, etc.).
Connecting the computer.
INPUT 6 terminal
Connecting video equipment with HDMI output terminal.
RS-232C terminal
Connecting the computer to control the projector.
TRIGGER terminal
When the projector is turned on, a control signal (DC 12V) outputs from this terminal. If an electric screen or other compatible device is connected, it can be turned on when the projector is turned on.
15
Kensington
13
Security Standard connector
Remote control sensor (rear)
Page
23
24
24
25
26
25
27
12
Numbers in Z refer to the main pages in this oper ation man ual where the topic is explained.
ON button
28
For turning the power on.
INPUT 1, 2, 3, 4, 5 and 6
STANDBY button
For putting the projector into the standby mode.
KEYSTONE button
For entering the Keystone Correction mode.
RETURN button
For returning to the previous menu screen during menu operations.
AUTO SYNC button
For automatically adjusting images when connected to a computer.
RGB/COMP. button
For switching to the respective input signal type.
FREEZE button
For freezing images.
29
32
41
46
48
38
29
buttons
For switching to the respective input modes.
MENU button
41
For displaying adjustment and setting screens.
Adjustment buttons
41
(P/R/O/Q)
• For selecting menu items.
• For adjusting the Keystone Correction when in the Keystone Correction mode.
ENTER button
41
For setting items selected or adjusted on the menu.
RESIZE button
36
For switching the screen size (STRETCH, SIDE BAR, etc.).
PICTURE MODE button
38
For selecting the appropriate picture.
Introduction
Backlight button
For lighting all buttons on the remote control.
Using the Kensington Lock on the projector
• This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with the system for instructions on how to use it to secure the projector.
IRIS button
38
For switching “HIGH BRIGHTNESS MODE”, “MEDIUM MODE” and “HIGH CONTRAST MODE”.
IMAGE SHIFT buttons
38
For shifting the projected image vertically.
13
Part Names and Functions (Continued)

Inserting the Batteries

Press the P mark on the cover and slide it
1
in the direction of the arrow.
Insert the batteries.
2
• Insert the batteries making sure the polarities
correctly match the m and n marks inside the battery compartment.
Attach the cover and slide it until it clicks
3
into place.
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.
Caution
• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
• Insert the batteries making sure the polarities correctly match the m and n marks inside the battery compartment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries. This may shorten the life of new batteries or may cause old batteries to leak.
• Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak. Battery fluid from leaked batteries is harmful to skin, therefore ensure that you first wipe them and then remove them using a cloth.
• The batteries included with this projector may run down in a short period, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries.
• Remove the batteries from the remote control if you will not be using the remote control for a long time.
• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
14

Usable Range

The remote control can be used to control the projector within the ranges shown in the illustration.
Remote control sensor (front)
30°
Introduction
Remote control signal transmitters
30°
Remote control
Note
• The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may differ depending on the screen material.
23n (7 m)
Remote control sensor (rear)
23n (7 m)
Remote control
30°
30°
Remote control signal transmitters
When using the remote control
• Ensure that you do not drop, expose to moisture or high temperature.
• The remote control may malfunction under a fluorescent lamp. In this case, move the projector away from the fluorescent lamp.
15

Quick Start

This section shows the basic operation (projector connecting with the video equipment). For details, see the page described below for each step.
Setup and Projection
In this section, connection of the projector and the video equipment is explained using one ex­ample.
3
STANDBY/ON
8
button
INPUT buttons
5
Focus ring
6
Zoom ring
6
HEIGHT
6
ADJUST lever
STANDBY button
8
ON button
3
INPUT 4 button
5
KEYSTONE button
7
Adjustment buttons
7
(P/R/O/Q)
ENTER button
7
1. Place the projector facing a wall or a screen
_P. 18
2. Connect the projector to the video equipment and plug the power cord into the AC socket of the projector
To INPUT 4 terminal
Connect the audio output of
AC socket
any video devices to an appropriate audio device.
3. Remove the lens cap and turn the projector on
On the
projector
On the remote
control
_PP. 22–28
_P. 28
16
4. Turn the video equipment on and start playback
5. Select the INPUT mode
Select the “INPUT 4” using the INPUT buttons on the projector or the INPUT 4 button on the remote control.
projector
On the
On the remote
control
On-screen display
_P. 29
INPUT 4
• When pressing the INPUT buttons on the projector, input mode switches in the following order:
• Pressing the INPUT buttons on the remote control also allows you to switch the input mode.
6. Adjust the focus, image size, and projector angle
1. Adjust the focus by
7.
Correct trapezoidal distortion (GEOMETRIC ADJUSTMENT)
1. Press c KEYSTONE on the remote control.
2. Press P/R/O/Q on the remote control to set the upper-left position of the projected image.
3. Press i ENTER on the remote control to set the position.
4. Follow steps 2 and 3 to also set the upper-right, lower-right, and lower-left positions of the projected image.
• When you confirm the lower left position, the screen adjustments will be set and setup will
INPUT1 INPUT2 INPUT3 INPUT4 INPUT5 INPUT6
turning the focus ring.
Focus ring
end.
2. Adjust the projection image size by turning the zoom ring.
Zoom ring
_PP. 30, 31
3. Adjust the projector angle using the HEIGHT ADJUST lever.
_PP. 32–35
Quick Start
8. Turn the Power off
Press the STANDBY/ON button on the projector or the STANDBY button on the remote control, and then press the button again while the confirmation message is displayed, to put the projector into standby mode.
On the
projector
• Unplug the power cord from the AC outlet after the cooling fan stops.
On the remote
control
On-screen Display
_P. 29
17

Setting up the Projector

Setting up the Projector

For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat and level. Doing so will eliminate the need for Keystone correction and provide the best image quality.

Standard Setup (Front Projection)

Place the projector at the required distance from the screen according
to the desired picture size. (See page 20.)
Example of standard setup
Side View
Screen
H
Lens center
L
Note
• Refer to page 20 for additional information concerning “Picture (Screen) Size and Projection Dis-
tance”.

Ceiling-mount Setup

It is recommended that you use the optional Sharp ceiling-mount bracket for this installa­tion. Before mounting the projector, contact your nearest Sharp Authorized Projector Dealer or Service Center to obtain the rec­ommended ceiling-mount bracket (sold sepa­rately).
• AN-60KT ceiling-mount bracket, its AN-
TK201 and AN-TK202 extension tubes.
Invert the image by setting “Ceiling + Front” in “PRJ Mode”. See page 49 for use of this function.
18

Projection (PRJ) Mode

The projector can use any of the 4 projection modes, shown in the diagram below. Select the mode most appropriate for the projection setting in use. (You can set the PRJ Mode in Options2 menu. See page 49.)
Table mounted, front projection
Menu item Front
Table mounted, rear projection (with a translucent screen)
Ceiling mounted, front projection
Menu item Ceiling + Front
Ceiling mounted, rear projection (with a translucent screen)
Menu item Rear Menu item Ceiling + Rear
Indication of the Projection Image Size and Projection Distance
Refer to page 20 for additional information concerning Picture (Screen) Size and Projection Distance”. Example: When using a wide screen (16:9)
Picture (Screen) Size
300"
200"
100"
80" 60"
52"
70"
×
29"
87"
×
×
39"
174"
49"
×
98"
261"×147"
Setup
"
6'11
"–
5'11
(1.8 m – 2.1 m)
7'11
9'2
"–
(2.4 m
"
2.8 m)
9'11
11'6
"–
(3.0 m
"
3.5 m)
19'10
(6.0 m
22'11
"–
7.0 m)
29'9
"
"
5
34'
"
(9.1 m – 10.5 m)
Projection Distance
19
Setting up the Projector (Continued)

Picture (Screen) Size and Projection Distance

The projection screen size varies according to the distance from the lens of the projec­tor to the screen. Install the projector so that projected images are projected onto the screen at the optimum size by referring to the table below. Use the values in the table as a reference when installing the projector.
When using a wide screen (16:9) and projecting 16:9 image
Picture (Screen) size Projection distance [L]
Diag. [χ] Width Height
300(762 cm)
270(686 cm)
250(635 cm)
200(508 cm)
150(381 cm)
100(254 cm)
80(203 cm)
70(178 cm)
60(152 cm)
40(102 cm)
χ
: Picture (Screen) size (diag.) (in/cm) L: Projection distance (ft/m) L1: Minimum projection distance (ft/m) L2: Maximum projection distance (ft/m) H: Distance from the lens center to the bottom of the image (in/cm) S: Adjustable range of image position (in/cm) See page 47.
261(664 cm)
235(598 cm)
218(553 cm)
174(443 cm)
131(332 cm)
87(221 cm)
70(177 cm)
61(155 cm)
52(133 cm)
35(89 cm)
147(374 cm)
132(336 cm)
123(311 cm)
98(249 cm)
74(187 cm)
49(125 cm)
39(100 cm)
34(87 cm)
29(75 cm)
20(50 cm)
Minimum [L1] Maximum [L2]
9(9.1 m)
29
9(8.2 m)
26
9(7.5 m)
24
10(6.0 m)
19
10(4.5 m)
14
11(3.0 m)
9
11(2.4 m)
7
11(2.1 m)
6
11(1.8 m)
5
0(1.2 m)
4
5(10.5 m)
34
11(9.4 m)
30
8(8.7 m)
28
11(7.0 m)
22
2(5.2 m)
17
6(3.5 m)
11
2(2.8 m)
9
0(2.4 m)
8
11(2.1 m)
6
7(1.4 m)
4
When using a normal screen (4:3) and projecting 4:3 image (SIDE BAR Mode)
Picture (Screen) size Projection distance [L]
Diag. [χ]
300(762 cm)
270(686 cm)
250(635 cm)
200(508 cm)
150(381 cm)
100(254 cm)
80(203 cm)
70(178 cm)
60(152 cm)
40(102 cm)
χ
: Picture (Screen) size (diag.) (in/cm) L: Projection distance (ft/m) L1: Minimum projection distance (ft/m) L2: Maximum projection distance (ft/m) H: Distance from the lens center to the bottom of the image (in/cm) S: Adjustable range of image position (in/cm) See page 47.
Width Height
240(610 cm)
216(549 cm)
200(508 cm)
160(406 cm)
120(305 cm)
80(203 cm)
64(163 cm)
56(142 cm)
48(122 cm)
32(81 cm)
180(457 cm)
162(411 cm)
150(381 cm)
120(305 cm)
90(229 cm)
60(152 cm)
48(122 cm)
42(107 cm)
36(91 cm)
24(61 cm)
Minimum [L1] Maximum [L2]
4(11.1 m)
36
9(10.0 m)
32
4(9.2 m)
30
3(7.4 m)
24
2(5.5 m)
18
1(3.7 m)
12
8(3.0 m)
9
6(2.6 m)
8
3(2.2 m)
7
10(1.5 m)
4
42
1(12.8 m)
10(11.5 m)
37
1(10.7 m)
35
1(8.6 m)
28
0(6.4 m)
21
0(4.3 m)
14
3(3.4 m)
11
10(3.0 m)
9
5(2.6 m)
8
7(1.7 m)
5
Distance from the lens center
to the bottom of the image [H]
1
/32(53 cm)
21
15
/16(48 cm)
18
17
/32(45 cm)
17
1
/64(36 cm)
14
33
/64(27 cm)
10
1
/64(18 cm)
7
39
/64(14 cm)
5
29
/32(12 cm)
4
13
/64(11 cm)
4
51
/64( 7 cm)
2
The formula for picture size and projection distance
[Feet/inches]
L1 (ft) = 0.03019χ / 0.3048 L2 (ft) = 0.03493χ / 0.3048 H (in) =0.17808χ / 2.54 S (in) = ±0.04151χ / 2.54
Distance from the lens center
to the bottom of the image [H]
47
/64 (65 cm)
25
11
/64 (59 cm)
23
29
/64 (54 cm)
21
5
/32 (44 cm)
17
7
/8 (33 cm)
12
37
/64 (22 cm)
8
55
/64 (17 cm)
6
6(15 cm)
9
/64 (13 cm)
5
7
/16 (9 cm)
3
The formula for picture size and projection distance
[Feet/inches]
L1 (ft) = 0.03694χ / 0.3048 L2 (ft) = 0.04275χ / 0.3048 H (in) = 0.21794χ / 2.54 S (in) = ±0.0508χ / 2.54
Adjustable range of
image position [S]
29
/32(12.5 cm)
4
13
/32(11.2 cm)
4
5
/64(10.4 cm)
4
17
/64(8.3 cm)
3
29
/64(6.2 cm)
2
41
/64(4.2 cm)
1
5
/16(3.3 cm)
1
9
/64(2.9 cm)
1
63
/64(2.5 cm)
21
/32(1.7 cm)
[m/cm]
L1 (m) = 0.03019 L2 (m) = 0.03493 H (cm) = 0.17808 S (cm) = ±0.04151
χ χ
Adjustable range of
image position [S]
6(15.2 cm)
13
5
/32 (13.7 cm)
5 (12.7 cm)
4(10.2 cm)
3 (7.6 cm)
2 (5.1 cm)
19
/32 (4.1 cm)
1
13
/32 (3.6 cm)
1
13
/64 (3.0 cm)
1
51
/64 (2.0 cm)
[m/cm]
L1 (m) = 0.03694 L2 (m) = 0.04275 H (cm) = 0.21794 S (cm) = ±0.0508
χ χ
χ
χ
χ χ
20
When using a normal screen (4:3) and projecting 16:9 image
Picture (Screen) size Projection distance [L]
Diag. [χ]
300(762 cm)
270(686 cm)
250(635 cm)
200(508 cm)
150(381 cm)
100(254 cm)
80(203 cm)
70(178 cm)
60(152 cm)
40(102 cm)
χ
: Picture (Screen) size (diag.) (in/cm) L: Projection distance (ft/m) L1: Minimum projection distance (ft/m) L2: Maximum projection distance (ft/m) H: Distance from the lens center to the bottom of the image (in/cm) S: Adjustable range of image position (in/cm) See page 47.
Width
240(610 cm)
216(549 cm)
200(508 cm)
160(406 cm)
120(305 cm)
80(203 cm)
64(163 cm)
56(142 cm)
48(122 cm)
32(81 cm)
Height
180(457 cm)
162(411 cm)
150(381 cm)
120(305 cm)
90(229 cm)
60(152 cm)
48(122 cm)
42(107 cm)
36(91 cm)
24(61 cm)
Minimum [L1] Maximum [L2]
27
24
22
18
13
9
7
6
5
3
3(8.3 m)
7(7.5 m)
9(6.9 m)
2(5.5 m)
8(4.2 m)
1(2.8 m)
3(2.2 m)
4(1.9 m)
5(1.7 m)
8(1.1 m)
7(9.6 m)
31
5(8.7 m)
28
4(8.0 m)
26
0(6.4 m)
21
9(4.8 m)
15
6(3.2 m)
10
5(2.6 m)
8
4(2.2 m)
7
4(1.9 m)
6
2(1.3 m)
4
Note
• Refer to page 18 concerning “Projection distance [L]” and “Distance from the lens center to the
bottom of the image [H]”.
• Allow a margin of error in the values in the diagrams.
Distance from the lens center to
the bottom of the image [H]
5
/16(49 cm)
19
3
/8(44 cm)
17
3
/32(41 cm)
16
7
/8(33 cm)
12
21
/32(25 cm)
9
7
/16(16 cm)
6
9
/64(13 cm)
5
1
/2(11 cm)
4
55
/64(10 cm)
3
37
/64(7 cm)
2
The formula for picture size and projection distance
[Feet/inches]
L1 (ft) = 0.02771χ / 0.3048 L2 (ft) = 0.03206χ / 0.3048 H (in) = 0.16346χ / 2.54 S (in) = ±0.0381χ / 2.54
Adjustable range of
image position [S]
1
/2(11.4 cm)
4
3
/64(10.3 cm)
4
3
/4(9.5 cm)
3
3 (7.6 cm)
1
/4(5.7 cm)
2
1
/2(3.8 cm)
1
13
/64(3.0 cm)
1
3
/64(2.7 cm)
1
29
/32(2.3 cm)
19
/32(1.5 cm)
[m/cm]
L1 (m) = 0.02771 L2 (m) = 0.03206 H (cm) = 0.16346 S (cm) = ±0.0381
χ
Setup
χ χ χ
21

Samples of Cables for Connection

For more details of connection and cables, refer to the operation manual of the connecting equipment.
• You may need other cables or connectors not listed below.
Equipment
Audio-visual equipment
Input
Signal
HDMI
video
Cable
HDMI cable (commercially available)
Terminal on the
projector
INPUT6
Camera/ video game
Compo-
nent
video
Compo-
nent
video
S-video
Video
Compo-
nent
video
Compo-
nent
video
S-video
3 RCA to 15-pin D-sub cable (optional accessory: AN-C3CP2)
S-video cable (commercially available)
Video cable (supplied)
Cables for a camera or a video game
Cables for a camera or a video game
Cables for a camera or a video game
3 RCA to 15-pin D-sub cable (optional accessory: AN-C3CP2)
RCA adaptor plug (commercially available)
INPUT1, 2Component cable (commercially available)
INPUT5
INPUT3
INPUT4
INPUT1, 2
INPUT5
INPUT3
Computer
22
Video
RGB video
Cables for a camera or a video game
RGB cable (commercially available)
INPUT4
INPUT5

Connecting to Video Equipment

Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet and turn off the devices to be connected. After making all connections, turn on the projector first and then the other devices.
When connecting the component video equipment to the component input termi­nal on the projector (INPUT1 or INPUT2)
To component output (Y, CB/PB, CR/PR) terminal
DVD, etc.
To INPUT1 terminal
Component cable (commercially available)
Connections
23
Connecting to Video Equipment (Continued)
When connecting to equipment with S-video output terminal (INPUT3)
To S-video output terminal
When connecting to equipment with video output terminal (INPUT4)
DVD, etc.
To INPUT3 terminal
S-video cable (commercially available)
To video output terminal
24
DVD, etc.
Video cable
Supplied
accessory
Video cable
To INPUT4 terminal
When connecting the component video equipment to the computer-RGB/ component input terminal on the projector (INPUT5)
To component output (Y, CB/PB, CR/PR) terminal
DVD, etc.
To INPUT5 terminal
3 RCA to 15-pin D-sub cable (optional accessory: AN-C3CP2)
When connecting to equipment with HDMI output teminal (INPUT6)
HDMI is a new specialized interface capable of delivering a video and audio signal to the terminal using just one cable. Since this projector does not support an audio signal by itself, use an amplifier or other audio device. For video connection, use a cable that conforms to HDMI standards. Using cables that do not conform to HDMI standards may result in a malfunction.
To HDMI output terminal
Note
• HDMI (High Definition Multimedia Interface) is a digital AV interface that can deliver a high-defini­tion video signal, multi-channel audio signal, and bi-directional control signal all in just one cable.
• Because it is compatible with the HDCP (High-bandwidth Digital Content Protection) system, the digital video signal does not degrade when transmitted, and a high-quality image with a simple connection can be enjoyed.
• When a DVI to HDMI conversion cable is connected to the HDMI terminal, a proper picture may not be displayable.
HDMI compatible device
To INPUT6 terminal
HDMI cable (type A) (commercially available)
Connections
25

Connecting to a Computer

When connecting a computer, ensure that it is the last device to be turned on after all the connections are made.
Ensure that you have read the operation manuals of the devices to be connected before making connections.
Computer
To RGB output terminal
RGB cable (commercially available)
Note
• See page 59 “Computer Compatibility Chart” for a list of computer signals compatible with the projec­tor. Use with computer signals other than those listed may cause some of the functions to not work.
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your near­est Macintosh Dealer.
Depending on the computer you are using, an image may not be projected unless the
computer’s external output port is switched on. (e.g. Press “Fn” and “F5” keys simultaneously when using a SHARP notebook computer). Refer to the specific instructions in your computer's
operation manual to enable your computer’s external output port.
Supplied
accessory
To INPUT5 terminal
26

Controlling the Projector by a Computer

When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS­232C adaptor (optional accessory: AN-A1RS) and an RS-232C serial control cable (cross type, commercially available), the computer can be used to control the projector and check the status of the projector. See page 58 for detail.
When connecting to a computer using an RS-232C serial control cable and a DIN­D-sub RS-232C adaptor
Computer
To RS-232C terminal
DIN-D-sub RS-232C adaptor (optional accessory: AN-A1RS)
RS-232C serial control cable (cross type, commercially available)
Note
• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the operation manual of the computer for details.
• See page 58 for connection of an RS-232C serial control cable.
To RS-232C terminal
Connections
Info
• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This may damage your computer or projector.
• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on. This may damage your computer.
27

Turning the Projector On/Off

Connecting the Power Cord

Plug the supplied power cord into the AC socket on the rear of the projector.

Turning the Projector on

Note that the connections to external equip­ment and power outlet should be done be­fore performing the operations written be­low. (See pages 23 to 28.)
Remove the lens cap and press SSTANDBY/ON on the projector or bON on the remote control.
Note
About the Lamp Indicator
The lamp indicator illuminates to indicate the status of the lamp.
Green: The lamp is on. Blinking in green: The lamp is warming up
or shutting down.
Red:The lamp is shut down abnormally
or the lamp should be replaced.
• When switching on the projector, a slight flick­ering of the image may be experienced within the first minute after the lamp has been illumi­nated. This is normal operation as the lamp’s control circuitry is stabilising the lamp output characteristics. It should not be regarded as faulty operation.
• If the projector is put into standby mode and immediately turned on again, the lamp may take some time to start projection.
Supplied
accessory
AC socket
Power cord
Info
• English is the factory default language. If you want to change the on-screen display to another language, change the language according to the procedure on page 50.
Lamp indicator
Power indicator
STANDBY/ON button
ON button
28

Turning the Power off (Putting the Projector into Standby Mode)

Press SSTANDBY/ON on the pro-
1
jector or aSTANDBY on the re­mote control, then press that but­ton again while the confirmation message is displayed, to put the projector into standby mode.
Unplug the power cord from the AC
2
outlet after the cooling fan stops.
• The power indicator on the projector blinks in green while cooling.
• The power indicator changes to red when the projector finishes cooling.
STANDBY button
On-screen Display (confirmation message)
Info
• Do not unplug the power cord during projection or cooling fan operation. This can cause dam­age due to rise in internal temperature, as the cooling fan also stops.

Image Projection

Switching the Input Mode

Select the appropriate input mode for the connected equipment.
Press the appropriate INPUT button on the remote control to select the desired input mode.
• When pressing INPUT (P/R) on the projector,
input mode switches in the following order:
INPUT1 INPUT2 INPUT3
INPUT6 INPUT5 INPUT4
R
Operation
Basic
INPUT buttons
29
Image Projection (Continued)

Adjusting the Projected Image

1 Adjusting the Focus
You can adjust the focus with the focus ring on the projector.
Rotate the focus ring to adjust the fo­cus while watching the projected image.
2 Adjusting the Screen Size
You can adjust the screen size using the zoom ring on the projector.
Rotate the zoom ring to enlarge or shrink the screen size.
3 Adjusting the Height
The height of the projector can be ad­justed using the adjustment feet at the front and rear of the projector.
When the screen is above the projec­tor, the projection image can be made higher by adjusting the projector.
Zoom ring
Focus ring
Lift the projector to adjust its
1
height while lifting the HEIGHT ADJUST lever.
Remove your hands from the
2
HEIGHT ADJUST lever of the pro­jector after its height has been finely adjusted.
• The angle of projection is adjustable up to 8 degrees from the surface on which the projector is placed.
30
HEIGHT ADJUST lever
Make small adjustments.
Use the rear adjustment foot to
3
make the projector level.
• The projector is adjustable ±1 degree from the standard position.
Note
• When adjusting the height of the projector, trapezoidal distortion occurs. Follow the pro­cedures in Keystone Correction to correct the distortion. (See page 32.)
Info
• Do not apply too much pressure on the pro­jector when the front adjustment foot comes out.
• When lowering the projector, be careful not to get your fingers caught in the area between the adjustment foot and the projector.
• Hold the projector firmly while lifting or carry­ing.
• Do not hold by the lens area.
Rear adjustment foot
Operation
Basic
31
Image Projection (Continued)

Correcting Trapezoidal Distortion

When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction.
There are the two types of the Keystone Correction.
1) The “GEOMETRIC ADJUSTMENT” method corrects trapezoidal distor­tion by specifying 4 marks on the screen.
2) The “H & V KEYSTONE” method fea­tures corrections to 2 axes (horizon­tal and vertical) based on numerical values.
KEYSTONE button
Adjustment buttons (P/R/O/Q)
RETURN button
ENTER button
32
Selecting the Type of Correction
Select the Keystone correction method. Press c KEYSTONE on the remote control.
• “GEOMETRIC ADJUSTMENT” will be
displayed.
• Each time c KEYSTONE is pressed, the
display toggles as follows:
GEOMETRIC
ADJUSTMENT
The display disappears.
H & V KEYSTONE
Note
• When corrections are made with Keystone cor­rection, the changes are saved even if the power cord is unplugged.
• Since Keystone correction digitally corrects the signal, resolution may slightly decrease when it is used. Moiré patterns and line dis­tortions may also be visible in detailed images. However, this is not a malfunction.
• If you cannot correct trapezoidal distortion with Keystone correction, change the placement position of the projector.
• Straight lines and the edges of the displayed image may appear jagged, when adjusting the Keystone setting.
• Also read “About Copyrights” on page 37.
GEOMETRIC ADJUSTMENT
H & V KEYSTONE
For correcting an image by designating the corner of the projected image. (See page 34.)
For correcting an image by designating the horizontal or vertical axes. (See page 35.)
Operation
Basic
33
Image Projection (Continued)
GEOMETRIC ADJUSTMENT
Info
• When adjusting a 4:3-aspect-ratio input sig­nal to a 4:3-aspect-ratio screen, correct the trapezoidal distortion by setting “RESIZE” to “STRETCH” (16:9).
Press c KEYSTONE on the re-
1
mote control repeatedly until “GEOMETRIC ADJUSTMENT” is displayed.
Adjust the focus, size, and projec-
2
tion angle so that the screen edges line up into the blue area.
• Line up the screen edges into the blue area as closely as possible.
Press P, R, O or Q to move the
3
position for the upper left of the image.
• Adjust the screen until the displayed red arrows line up in the upper left.
Press i ENTER to set the posi-
4
tion.
• The arrow in the upper right turns red.
Repeat the same procedure with
5
the positions for the upper right, lower right and lower left of the image.
• When you press e RETURN at this point, you will return to the previous screen.
• If you press e RETURN before adjust­ing the upper left corner, the Reset Con­firmation screen displays.
When you confirm the lower left posi-
tion, the screen adjustments will be set and the “GEOMETRIC ADJUSTMENT” mode will end.
R On-screen display
Adjust upper left corner
GEOMETRIC ADJUSTMENT ADJUST NEXT
Geometric Adjustment
Blue
area
Screen
Upper Left Upper Right
Lower Left Lower Right
RESET END
Note
• The placement of the screen and the projector may result in the image aspect ratio becoming slightly distorted.
• Try “H&V KEYSTONE” when “GEOMETRIC ADJUSTMENT” does not fully correct trapezoi­dal distortion.
34
H & V KEYSTONE
Project the image and adjust the
1
focus, image size, and projection angle.
Press c KEYSTONE on the re-
2
mote control repeatedly until “H & V KEYSTONE” is displayed.
• When the “GEOMETRIC ADJUSTMENT” mode has been used to adjust the im­age, a confirmation screen displays be­fore the “H & V KEYSTONE” screen, ask­ing if you want to reset the adjustments or not. Then select RESET.
R On-screen display
H&V KEYSTONE
END
ENTER
ADJUST
RESET
Press P or R on the remote con-
3
trol to align the left and right sides of the projected image.
Press O or Q on the remote con-
4
trol to align the upper and lower sides of the projected image.
Press c KEYSTONE or i ENTER
5
on the remote control and the H&V KEYSTONE mode ends.
Note
• If adjustments are made using both “H KEY­STONE” and “V KEYSTONE” at the same time, the image aspect ratio may become slightly distorted.
• When adjusting “H KEYSTONE” and “V KEY­STONE” at the same time, the values of adjust­able angles for each setting become smaller.
• The adjustable value of the “V KEYSTONE” becomes extremely small when “H KEY­STONE” is made to be the maximum value.
Vertical Keystone Correction
(Adjustment with P / R)
Horizontal Keystone Correction
(Adjustment with O / Q)
Operation
Basic
35
Image Projection (Continued)

Resize Mode

This function allows you to modify or customize the resize mode to enhance the input image. De­pending on the input signal, you can choose “STRETCH”, “SIDE BAR”, “CINEMA ZOOM” or “DOT
BY DOT (Computer input only)” image.
Press m RESIZE on the projector or jRESIZE on the remote control.
On the projector
On the remote control
RESIZE button
VIDEO
RESIZE button
• “STRETCH” is fixed when 540P, 720P or 1080I signals are entered.
Input Signal
DVD / Video Image type
4:3 aspect ratio
480I, 480P, 576I,
576P, NTSC, PAL,
SECAM
Letter box
Squeezed
16:9 aspect ratio
STRETCH SIDE BAR
Output screen image
CINEMA ZOOM
540P, 720P, 1080I
16:9 aspect ratio
: Cutout area on which images cannot be projected.
36
Computer
Input Signal
Computer
Resolution lower than
XGA
XGA
(1024K768)
1280K720
: Cutout area on which images cannot be projected.
Note
• You can select “CINEMA ZOOM” when with a “VGA/SVGA” signal with a vertical frequency 60 Hz and less. However, when a “VGA/SVGA” signal with a vertical frequency of more than 60 Hz is used, “CINEMA ZOOM” is not available.
Image
type
4:3 aspect
ratio
4:3 aspect
ratio
16:9 aspect
ratio
STRETCH
Output screen image
SIDE BAR
CINEMA
ZOOM
DOT BY DOT
About Copyrights
• When using the RESIZE function to select an image size with a different aspect ratio to a TV program or video image, the image will look different from its original appear­ance. Keep this in mind while choosing an image size.
• The use of the Resize, Keystone Correction, Subtitle, or Overscan function to com­press or stretch the image for commercial purposes/public displays in a café, hotel, etc. may be an infringement of copyright protected by law for copyright holders. Please use caution.
• While watching non-widescreen images (4:3), if you use the RESIZE function to fill the screen or use the Overscan function to change the aspect ratio of a fixed-ratio input signal, parts of the outer edge of the image will be cut off or distorted. To watch original images as the producers intended, set RESIZE to “SIDE BAR” and Overscan to its default setting.
Operation
Basic
37

Operating with the Remote Control

Shifting the Projected Im­age Vertically (Image Shift)
For easier viewing, this function shifts the entire image projected on the screen up or down when projecting 16:9 images from DVD players or other con­nected devices.
Press PIMAGE SHIFT.
• The image moves up.
Press RIMAGE SHIFT.
• The image moves down.
Note
• The Image Shift function operates when “Resize” is not set to “DOT BY DOT”.
• For details on Image Shift, see page 47.

Switching the Iris Setting

This function controls the quantity of the projected light and the contrast of the image.
Press lIRIS.
• Each time the button is pressed while the dis­play is on, the mode is switched in the follow­ing order:
HIGH BRIGHTNESS MODE MEDIUM MODE
HIGH CONTRAST MODE
IMAGE SHIFT buttons
PICTURE MODE button
IRIS button
FREEZE button

Selecting the Picture Mode

Note
• For details on Iris, see page 45.

Freezing a Moving Image

Press hFREEZE.
1
• The projected image is frozen.
Press hFREEZE again to return
2
to the moving image from the cur­rently connected device.
38
You can select the appropriate picture mode to best match the projected im­age you are watching.
Press kPICTURE MODE.
• When pressing kPICTURE MODE, the picture
mode changes in the following order:
Standard Dynamic
Note
• See page 43 for details on the picture mode.
Natural
Movie2 Movie1Memory

Menu Items

The following shows the items that can be set in the projector. The selectable items vary depending on the selected input, input signals, or adjustment values. Items that cannot be selected will be greyed out.
“Picture” menu
PAGE 1
Picture INPUT 1
Picture Mode Contrast 0 Bright Color Tint Sharp Red Blue
SEL./ADJ. RETURN
0 0 0 0 0 0
Standard
ENTER END
Main menu Sub menu
Picture
Picture Mode
Page 43 Page 43
Contrast
Bright
Color
Tint
Sharp
Red
Blue
Standard Natural Dynamic Movie1 Movie2 Memory
+30-30
+30-30
*2
+30-30
*2
+30-30
*2
+30-30
+30-30
+30-30
Page 43
PAGE 2
Picture INPUT 1
Picture Mode
CLR Temp
BrilliantColor™ C. M. S. Progressive DNR IRIS Lamp Setting
Reset
SEL./ADJ. RETURN
K7500
1
Single ADJ END
Standard
3D Progressive Level 1 High Brightness Bright
“C.M.S.”
C. M. S.
C. M. S. - Hue
C. M. S. - Saturation C. M. S. - Value
Reset
SEL./ADJ. RETURN
*1 When a video signal, S-video signal, or component 480I/
576I signal is input and the Progressive mode is set to “3D Progressive” or “Film Mode”, the C.M.S. function cannot be used.
2
Item that cannot be set when inputting an RGB signal
*
through INPUT 5 or INPUT 6.
R Y G C B M
Reset
0 0 0 0 0 0
ENTER END
CLR Temp
Page 44
BrilliantColor™ [0/1/2]
5500K 6500K 7500K 8500K 9300K 10500K
Page 43
C.M.S.
Page 44
Progressive
Page 44
DNR OFF
Page 45
IRIS High Brightness
Page 45
Lamp Setting
Page 45
Reset
*1
C.M.S.-Hue
Page 44
C.M.S.-Saturation
Page 44
C.M.S.-Value
Page 44
Reset
*1
*2
R
Y
G
C
B
M
Reset
2D Progressive 3D Progressive Film Mode
Level 1 Level 2 Level 3
Medium Mode High Contrast
Bright Eco + Quiet
+30-30
+30-30
+30-30
+30-30
+30-30
+30-30
Features
Useful
39
Menu Items (Continued)
“Fine Sync” menu
Fine Sync INPUT 5
Clock Phase H-Pos V-Pos
Reset Special Modes Auto Sync
Cur. sig. freq : H 33.8 kHz / V 60 Hz
SEL./ADJ.
RETURN
0 0 0 0
1080I On
ENTER END
• The “Fine Sync” menu is not available for INPUT 3 or INPUT 4.
Options1 menu
Options 1 INPUT 1
Image Shift Overscan H Overscan V Subtitle OSD Display Video System Signal Type HDMI Setting Background Auto Power Off
SEL./ADJ. RETURN
*1 Item that can be set when using INPUT 3 or
INPUT 4.
2
Item that can be set when using IINPUT 5 or
*
INPUT 6.
0 0 0 0
ENTER END
On Auto Auto Standard Blue On h0Lamp Timer(Life) 100%
Options2 menu
Options 2 INPUT 1
PRJ Mode RS-232C STANDBY Mode Fan Mode
All Reset
Language
SEL./ADJ. RETURN
Front 9600 bps Eco Normal
English
ENTER END
Main menu Sub menu
Fine Sync
Clock
+150-150
Page 46 Page 46
Phase
+30-30
Page 46
H-Pos
+150-150
Page 46
V-Pos
Page 46
Reset
Special Modes 1035I
Page 46
Auto Sync [On/Off]
+60-60
1080I The resolution changes depending on the input signal.
Page 46
Cur. sig. freq
Main menu Sub menu
Options 1
Page 47
Page 46
Image Shift
Page 47
Overscan H Overscan V
+24-24
+30-30 +30-30
Page 47
Subtitle
+30-30
Page 47
OSD Display [On/Off]
Page 48
Video System
Page 48
Signal Type
Page 48
HDMI Setting
Page 48
Background
Page 48
Auto Power Off [On/Off]
*1
*2
Auto PAL SECAM NTSC 4.43
Auto RGB Component
Standard Enhanced
Blue None
Page 49
Lamp Timer(Life)
Main menu Sub menu
Options2
Page 49
Page 49
PRJ Mode
Page 49
RS-232C
Page 50
STANDBY Mode
Page 50
Fan Mode
Page 50
All Reset
Front Ceiling + Front Rear Ceiling + Rear
9600bps 115200bps
Standard Eco
Normal High
Page 50
Language
Page 50
English Deutsch Español Nederlands Français Italiano
NTSC 3.58 PAL-M PAL-N PAL-60
Svenska Português
40

Using the Menu Screen

ENTER button
Adjustment buttons (P/R/O/Q)
MENU button

Menu Selections (Adjustments)

Example: Adjusting “Bright”.
• This operation can also be performed by using the buttons on the projector.
Press dMENU.
1
• The “Picture” menu screen for the se­lected input mode is displayed.
Press Q or O to select the menu
2
icon to adjust.
• The selected icon is highlighted.
Menu icon Menu screen
Picture
Fine Sync
Options1
Options2
Example: “Picture” screen menu for INPUT 1 mode
Menu icons
Picture INPUT 1
Picture Mode Contrast 0 Bright Color Tint Sharp Red Blue
Adjustment buttons (P/R/O/Q)
MENU button
ENTER button
RETURN button
• Press eRETURN to re-
turn to the previous screen when the menu is displayed.
Selected input mode
Standard
0 0 0 0 0 0
Features
Useful
Note
• The “Fine Sync” menu is not available for INPUT 3 or INPUT 4.
SEL./ADJ. RETURN
ENTER END
41
Using the Menu Screen (Continued)
Press P or R to select the item to
3
adjust.
• The selected item is highlighted.
To adjust the projected image while watching it
Press iENTER.
• The selected item (e.g. “Bright”) is dis­played by itself at the bottom of the screen.
• When pressing P or R, the following item (“Color” after “Bright”) will be displayed.
Note
• Press iENTER again to return to the
previous screen.
Picture INPUT 1
Picture Mode Contrast 0
Bright
Color Tint Sharp Red Blue
SEL./ADJ. RETURN
Standard
0
0 0 0 0 0
Single ADJ END
Items to be adjusted
The item displayed by itself
Picture INPUT 1
SEL./ADJ. RETURN
0Bright
Rtn. Menu END
Press O or Q to adjust the item
4
selected.
• The adjustment is stored.
Press dMENU.
5
• The menu screen will disappear.
Picture INPUT 1
Picture Mode Contrast 0
Bright
Color Tint Sharp Red Blue
SEL./ADJ. RETURN
Standard
15
0 0 0 0 0
Single ADJ END
Note
• The d MENU button does not function while the projector is operating the “Auto Sync” or “FREEZE”
functions.
42

Picture Adjustment (“Picture” menu)

Menu operation n Page 41
Q PAGE 2Q PAGE 1
Picture INPUT 1
Picture Mode Contrast 0 Bright Color Tint Sharp Red Blue
1 1

1 Selecting the Picture Mode

1 1
Standard
0 0 0 0 0 0
Picture INPUT 1
Picture Mode
CLR Temp
BrilliantColor™ C. M. S. Progressive DNR IRIS Lamp Setting
Reset
K7500
1
Standard
3D Progressive Level 1 High Brightness Bright
Selectable
items
Standard
Natural
Dynamic
Movie1
Movie2
Memory
Description
For standard image
A balanced color image is obtained.
A vivid image is obtained.
Makes the black levels of the dark portions of the screen more pronounced and vivid.
Reduces glare and creates a subdued tone.
Allows you to store your picture adjustment settings. The settings
The default settings of each item when selecting Picture Mode
CLR Temp
7500K
7500K
7500K
6500K
6500K
7500K
BrilliantColor™
0
0
2
0
0
0
IRIS
High Brightness
High Brightness
High Brightness
High Brightness
Medium Mode
High Brightness
Lamp Setting
Bright
Bright
Bright
Eco + Quiet
Eco + Quiet
Bright
stored effect each input mode.
You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are retained in memory.
Note
• You can also press k PICTURE MODE on the remote control to select the picture mode.
(See page 38.)
22

2 Adjusting the Image

22
Adjustment items
Contrast
Bright
1
Color*
1
Tint*
1
Sharp*
Red
Blue
BrilliantColor™*
*1Item that cannot be adjusted in RGB mode.
2
*
BrilliantColor™ uses Texas Instruments' BrilliantColor™ technology. As the BrilliantColor™ level is increased,
2
For less contrast.
For less brightness.
For less color intensity.
For making skin tones purplish.
For less sharpness.
For weaker red.
For weaker blue.
For making the effect weaker.
O button
For more contrast.
For more brightness.
For more color intensity.
For making skin tones greenish.
For more sharpness.
For stronger red.
For stronger blue.
For making the effect stronger.
Q button
the image becomes brighter while the color reproduction is kept at a high level.
Features
Useful
Note
• To reset all adjustment items, select “Reset” and press iENTER. The Picture Mode
settings of the selected input return to the default settings.
43
Picture Adjustment (“Picture” menu) (Continued)
Menu operation n Page 41
33
3 Adjusting the Color
33
Temperature
Selectable
items
5500K 6500K 7500K 8500K 9300K 10500K
• Values on “CLR Temp” are only for general standard purposes.
For lower color temperature for warmer, reddish incandescent-like images.
For higher color temperature for cooler, bluish, fluorescent-like images.
Note
Description
P R
When “Saturation” is selected, the selected color becomes O: lighter. Q: thicker.
When “Value” is selected, the selected color becomes O: darker. Q: brighter.
To reset the adjustment values of each color to the default settings, select “Reset” and press i ENTER.
Info
• When a video signal, S-video signal, or compo­nent 480I/576I signal is input, set “Progressive” mode to “2D Progressive” and then adjust the colors.
55

5 Progressive

55
44

4 Adjusting the Colors

44
Select “C.M.S.” (Color Management System) in the “Picture” menu and then press i ENTER.
This function adjusts each of the six main colors that comprise the color wheel, altering their “Hue”, “Saturation”, or “Value”.
Selectable items
C.M.S.-Hue
C.M.S.-Saturation
C.M.S.-Value
Reset
Sets the hue of the main colors.
Sets the saturation of the main colors
Sets the brightness of the main colors.
The adjustments of “Hue”, “Saturation” and “Value” of all colors are reset to the default setting.
Description
Adjusting “Hue”, “Saturation”, or “Value”.
1Press P or R to select either “Hue”, “Saturation”, or
“Value” and then press i ENTER.
2Select the color to be adjusted with P or R and
adjust it with O or Q.
Example of adjusting the “Hue”
Main colors R (Red) Y (Yellow) G (Green) C (Cyan) B (Blue)
Magenta
M (
O button Closer to magenta Closer to red Closer to yellow Closer to green Closer to cyan
)
Closer to blue
Q button Closer to yellow Closer to green Closer to cyan Closer to blue Closer to magenta Closer to red
44
Selectable
items
2D Progressive
3D Progressive
Film Mode
* The film source is a digital video recording with the
original encoded as is at 24 frames/second. The projector can convert this film source to progres­sive video at 60 frames/second with NTSC and PAL60Hz or at 50 frames/second with PAL50Hz and SECAM to play back a high-definition image.
• In NTSC or PAL60Hz, even if the 3D Progres­sive mode has been set, the three-two pull down enhancement will be enabled automati­cally when the film source has been entered.
• When the image is blurred or noisy, switch to the optimal mode.
• When using progressive inputs, inputs are di­rectly displayed so that 2D Progressive, 3D Progressive and Film Mode cannot be selected.
Useful to display fast-moving images such as sports.
Useful to display relatively slow­moving images such as drama and documentary more clearly.
Reproduces the image of film source* clearly. Displays the optimized image of film transformed with three-two pull down (NTSC and PAL60Hz) or two-two pull down (PAL50Hz and SECAM) enhance­ment to progressive mode images.
Note
Description
Info
• The settings can be made either when INPUT3 or INPUT4 are selected or when INPUT1, 2, INPUT5, or INPUT6 are selected and the in­put signal is 480
I or 576I.
Menu operation n Page 41
66
6 Reducing Image Noise
66
(DNR)
Video digital noise reduction (DNR) provides high quality images with minimal dot crawl and cross color noise.
Selectable items
OFF
Level 1-3
Note
Set DNR” to OFF in the following cases:
• When the image is blurry.
• When the contours and colors of moving im­ages drag.
• When TV broadcasts with weak signals are projected.
DNR does not function.
Sets the DNR level for viewing a clearer picture.
Description
77
7 Switching the Iris
77
Setting
This function controls the quantity of the pro­jected light and the contrast of the image.
Selectable items
High Brightness
Medium Mode
High Contrast
Note
• You can also use l IRIS on the remote con-
trol to change the Iris. (See page 38.)
88

8 Lamp Setting

88
Select-
Bright-
able
ness
items
100%
Bright
Approx.
Eco +
87%
Quiet
High brightness is given priority over high contrast.
Intermediate mode between high contrast and high brightness.
High contrast is given priority over high brightness.
Fan
sound
Normal
Low
Description
Powe r consumption (When using
AC 100V)
355W
310W
Lamp Life
Approx.
2,000 hours
Approx.
3,000 hours
Note
• When “Lamp Setting” is set to “Eco+Quiet”, the power consumption will decrease and the lamp life will extend. (Projection brightness decreases approximately 13%.)
Features
Useful
45

Computer Image Adjustment (“Fine Sync” menu)

Fine Sync INPUT 5
Clock Phase H-Pos V-Pos
Reset Special Modes Auto Sync
Cur. sig. freq : H 33.8 kHz / V 60 Hz
11
1 Adjusting the
11
0 0 0 0
1080I On
Computer Image
Use the Fine Sync function in case of irregulari­ties such as vertical stripes or flickering in por­tions of the screen.
Selectable items
Clock
Phase
H-Pos
V-P os
Note
• You can automatically adjust the computer image by setting “Auto Sync” in the “Fine Sync” menu to “On” or pressing f AUTO SYNC on the remote control.
• “Clock”, “Phase”, “H-Pos” and “V-Pos” can­not be adjusted when INPUT 6 is selected.
• The adjustable area of each item may be changed according to the input signal.
• To reset all adjustment items, select “Reset” and press i ENTER.
Adjusts vertical noise.
Adjusts horizontal noise (similar to tracking on your VCR).
Centers the on-screen image by moving it to the left or right.
Centers the on-screen image by moving it up or down.
Description
22

2 Special Modes Setting

22
Ordinarily, the type of input signal is detected and the correct resolution mode is automatically selected. However, for some signals, the opti­mal resolution mode in “Special Modes” in the “Fine Sync” menu may need to be selected to match the computer display mode.
Note
• Avoid displaying computer patterns which repeat every other line (horizontal stripes). (Flickering may occur, making the image hard to see.)
• Information on the currently selected input sig­nal can be confirmed in item 4.
33
3 Auto Sync (Auto Sync
33
Selectable items
On
Off
Note
• Auto Sync adjustment is also performed by pressing f AUTO SYNC on the remote con­trol.
• The Auto Sync adjustment may take some time to complete, depending on the image of the computer connected to the projector.
• When the optimum image cannot be achieved with Auto Sync adjustment, use manual ad­justments.
Menu operation n Page 41
Adjustment)
Description
Auto Sync adjustment will occur when the projector is turned on or when the input signals are switched, when connected to a computer.
Auto Sync adjustment is not automatically performed.
46
44
4 Checking the Input
44
Signal
This function allows you to check the current in­put signal information.

Using the “Options” Menu

Options 1 INPUT 1
Image Shift
1
Overscan H
2
Overscan V
2
Subtitle
3
OSD Display
4
Video System
5
Signal Type
6
HDMI Setting
7
Background
8
Auto Power Off
9 0
Settings on the Options 1 menu
0 0 0 0
On Auto Auto Standard Blue On h0Lamp Timer(Life) 100%
Menu operation n Page 41
22
2

Adjusting the Overscan

22
This function allows you to adjust the Overscan area ratio (display area ratio).
Orientation
Overscan H (Horizontal)
Overscan V (Vertical)
O button
Reduces the image. (The display area ratio becomes larger.)
Q button
Enlarges the image. (The display area ratio becomes smaller.)
11
1 Adjusting the Image
11
Position
You can move the projected image vertically.
O button
Note
• The Image Shift function cannot be selected when “Resize” is set to “DOT BY DOT”.
• You can also use the IMAGE SHIFT buttons on the remote control to adjust the image po­sition.
Q button
Note
• This function can only be adjusted when a video, S-video, or Component signal is input.
• If the display area ratio is set too large, noise may appear at the screen edges. If this hap­pens, set the display area ratio to a smaller value.
• When “Resize” is set to “CINEMA ZOOM”, depending on the input signal, “Overscan V” may not be adjustable.
• Also read “About Copyrights” on page 37.
33
3
Adjusting the Vertical Size of
33
the Display (Subtitle Setting)
With this function, you can adjust the vertical size of the display to allow for subtitles.
O button
Q button
When changing the screen with the Subtitle set­ting, not only the bottom of the screen rises, but also the upper part is changed to a certain point.
• The Subtitle setting can be adjusted more ef­fectively with the Overscan and Image Shift functions.
• The Subtitle setting only works when “Resize” is set to “CINEMA ZOOM”.
• The adjustment area changes according to the input signal.
The image is compressed by adjusting the vertical size of the display.
The image is enlarged by adjusting the vertical size of the display.
Note
Features
Useful
47
Using the “Options” Menu (Continued)
Menu operation n Page 41
44
4

Setting On-screen Display

44
Selectable
items
On
Off
55
5
55
All On-screen Displays are displayed.
INPUT/FREEZE/AUTO SYNC/RESIZE/ PICTURE MODE/IRIS are not displayed.
Setting the Video
Description
System
This function can only be set in INPUT 3 or INPUT 4.
The video input system mode is factory preset to “Auto”;however, a clear picture from the con­nected audio-visual equipment may not be re­ceived, depending on the video signal difference. In that case, switch the video signal.
Selectable items
PA L
SECAM
NTSC4.43
NTSC3.58
When connected to PAL video equipment.
When connected to SECAM video equipment.
When reproducing NTSC signals in PAL video equipment.
When connected to NTSC video equipment.
Description
66

6 Signal Type Setting

66
This function allows you to select the input sig­nal type (RGB or Component) for INPUT 5 or INPUT 6.
Selectable items
Auto
RGB
Component
Note
• You can also select “Signal Type” using g RGB/COMP. on the remote control (INPUT 5 or INPUT 6).
77
7

Selecting the HDMI Setting

77
When there is an HDMI-capable device con­nected to INPUT 6, an optimum picture may not be displayed if the device’s output signal type and the projector’s input signal type do not match. If this should occur, switch the HDMI Setting.
Selectable items
Standard
Enhanced
Automatically selects the appropriate input signal between RGB and Component.
Set when RGB signals are received.
Set when component signals are received.
When the black levels of the image show banding or appear faded, select the option that results in the best picture quality. (In most circumstances, “Standard” should be selected.)
Description
Description
48
Note
• The HDMI Setting can be selected only when INPUT 6 is selected.
88
8
Selecting the Background
88
Image
Selectable items
Blue
None
Blue screen
— (Black screen)
Description
99
9 Auto Power Off
99
Function
Selectable
items
On
Off
When no input signal is detected for more than 15 minutes, the projector will automatically enter standby mode.
The Auto Power Off function will be disabled.
Description
Menu operation n Page 41
Options 2 INPUT 1
PRJ Mode
1
RS-232C
2
STANDBY Mode
3
Fan Mode
4
All Reset
5
Language
6
Settings on the Options 2 menu
Front 9600 bps Eco Normal
English
Note
• When the Auto Power Off function is set to “On”, 5 minutes before the projector enters standby mode, the message “Enter STANDBY mode in X min.” will appear on the screen to indicate the remaining minutes.
00
0 Checking the Lamp Life
00
Status
You can confirm the cumulative lamp usage time and the remaining lamp life (percentage).
Lamp usage condition
Life
Operated exclusively with Lamp Setting set to “Eco + Quiet”
Operated exclusively with Lamp Setting set to “Bright”
Note
• It is recommended that the lamp be changed when the remaining lamp life becomes 5%.
• The lamp life may vary depending on the us­age condition.
Remaining lamp life
100%
Approx. 3,000 hours
Approx. 2,000 hours
Approx. 150 hours
Approx. 100 hours
5%
11
1 Reversing/Inverting
11
Projected Images
Selectable items
Front
Ceiling + Front
Rear
Ceiling + Rear
See page 19 for details of Projection (PRJ) Mode.
Normal image (Projected from the front of the screen)
Inverted image (Projected from the front of the screen with an inverted projector)
Reversed image (Projected from the rear of the screen or with a mirror)
Reversed and inverted image (Projected with a mirror)
Description
Features
Useful
49
Using the “Options” Menu (Continued)
Menu operation n Page 41
22
2
Selecting the Transmission
22
Speed (RS-232C)
Make sure that both the projector and computer are set for the same baud rate.
Selectable
items
9600bps
Transmission speed is slow.
Description
P R
115200bps
33
3
33
Transmission speed is rapid.

Reducing the Power Consumption When the Power Is in Standby Mode

When “STANDBY Mode” has been set to “Stan­dard”, the RS-232C function is activated and power is consumed even in standby mode. It is recommended that “STANDBY Mode” be set to “Eco” when it is not being used. This reduces power consumption when the projector is in standby mode.
Selectable items
Standard
Eco
Note
• When you want to control the projector using the RS-232C function, set to “Standard”.
The RS-232C function is activated even if the projector is in standby mode.
The RS-232C function is switched off when the projector is in standby mode.
Description
44

4 Fan Mode Setting

44
This function changes the fan rotation speed.
Selectable
items
Normal
High
When “Fan Mode” is set to “High”, the fan rotation speeds up, and the fan noise becomes louder.
55
5
55
Suitable for normal environments.
Select this when using the projector at altitudes of approximately 4,900 feet (1,500 meters) or more.
Returning to the Default
Description
Settings
Use “All Reset” to initialize all the adjustments you have made to the default settings.
Note
The following items cannot be initialized.
• “Fine Sync” menu – Special Modes
• “Options1” menu – Lamp Timer (Life) – Language
66
6
Selecting the On-screen
66
Display Language
The projector can switch the on-screen display language among 11 languages.
English Deutsch Español Nederlands Français Italiano
Svenska Português
50

Maintenance

Cleaning the projector
Ensure that you have unplugged the power cord before cleaning the projector.
The cabinet as well as the operation panel is made of plastic. Avoid using benzene or thinner, as these can damage the finish on the cabinet.
Do not use volatile agents such as insecticides on the projector. Do not attach rubber or plastic items to the projector for long periods. The effects of some of the agents in the plastic may cause damage to the quality or finish of the projector.
Wipe off dirt gently with a soft flannel cloth.
When the dirt is hard to remove, soak a cloth in
a mild detergent diluted with water, wring the cloth well and then wipe the projector. Strong cleaning detergents may discolor, warp or damage the coating on the projector. Make sure to test on a small, inconspicuous area on the projector before use.
Mild detergent
Mild detergent diluted
with water
Cleaning the lens
Use a commercially available blower or lens cleaning paper (for glasses and camera lenses) for cleaning the lens. Do not use any liquid type cleaning agents, as they may wear off the coating film on the surface of the lens.
As the surface of the lens can easily get damaged, be sure not to scrape or hit the lens.
Cleaning the exhaust and intake vents
Use a vacuum cleaner to clean dust from the exhaust vent and the intake vent.
Thinner
Wax
Info
• If you want to clean the air vents during pro­jector operation, be sure to press S STANDBY/ON on the projector or aSTANDBY on the remote control and put the projector into standby mode. After the cool­ing fan has stopped, clean the vents.

Appendix

51

Maintenance Indicators

The warning lights (power indicator, lamp indicator and temperature warning indicator) on the projector indicate problems inside the projector.
If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the projector will enter standby mode. After the projector has entered standby mode, follow the procedures given below.
Top View
Temperature warning indicator
Lamp indicator
Power indicator
About the temperature warning indicator
If the temperature inside the projector increases, due to blockage of the air vents, or the setting location,
” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp
“ will turn off and the temperature warning indicator will blink, the cooling fan will run, and then the projec­tor will enter standby mode. After “
53.
About the lamp indicator
” appears, be sure to perform the measures described on page
When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will automatically turn off and then the projector will automatically enter standby mode. At this time, the lamp indicator will illuminate in red.
If you try to turn on the projector a fourth time without replacing the lamp, the projector will not turn on.
Indicators on the Projector
Power indicator
Lamp indicator
Temperature warning indicator
Red on
Green on
Red blinks
Green blinks
Green on
Green blinks
Red on
Off
Red on
Normal (Standby)
Normal (Power on) Abnormal (See page 53.) Normal (Cooling)
Normal
The lamp is warming up or shutting down.
The lamp is shut down abnormally or requires to be changed. (See page 53.)
Normal
The internal temperature is abnormally high. (See page 53.)
52
Maintenance indicator
Tempera-
ture
warning
indicator
Lamp
indicator
Power
indicator
Green on
when the
warming
Green on/
(Cooling)
Normal
Off
(Green
blinks
lamp is
up or
turning
off.)
Red on
Green blinks
Abnormal
Red on
(Standby)
Red on
Red on
(Standby)
Red
blinks
Problem
The internal temperature is abnormally high.
The lamp does not illuminate.
Time to change the lamp.
The lamp does not illuminate.
The power indicator blinks in red when the projector is on.
Cause
• Blocked air intake
• Cooling fan breakdown
• Internal circuit failure
• Clogged air intake
• The lamp is shut down abnormally.
• Remaining lamp life becomes 5% or less.
• Burnt-out lamp
• Lamp circuit failure
• The lamp unit cover is open.
Possible Solution
• Relocate the projector to an area with proper ventilation. (see page 8)
• Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center for repair.
• Disconnect the power cord from the AC outlet, and then connect it again.
• Carefully replace the lamp. (See page 55.)
• Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center for repair.
• Please exercise care when replacing the lamp.
• Securely install the cover.
• If the power indicator blinks in red even when the lamp unit cover is securely installed, contact your nearest Sharp Authorized Projector Dealer or Service Center for advice.
Info
• If the temperature warning indicator illuminates, and the projector enters standby mode, follow the possible solutions above and then wait until the projector has cooled down completely before plug­ging in the power cord and turning the power back on. (At least 10 minutes.)
• If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illumi­nate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again.
• The cooling fan keeps the internal temperature of the projector constant and this function is con­trolled automatically. The sound of the cooling fan may change during operation because the fan speed may change and this is not a malfunction.
• Do not unplug the power cord after the projector has entered standby mode and while the cooling fan is running. The cooling fan runs for about 90 seconds.
Appendix
53

Regarding the Lamp

Lamp

It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. (see page 49)
Purchase a replacement lamp of type AN-100LP from your place of purchase, nearest Sharp Authorized Projector Dealer or Service Center.

Caution Concerning the Lamp

This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking.
When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.
Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to assure safe operation.
Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.

Replacing the Lamp

• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burn or injury.
Carefully change the lamp by following the instructions described in this section. * If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.
* If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized
Projector Dealer or Service Center for repair.
54

Removing and Installing the Lamp Unit

Warning!
• The lamp unit becomes very hot while the pro­jector is operating. Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burns or injury.
Info
• Make sure that you remove the lamp unit by
the handle. Do not touch the glass surface of the lamp unit or the inside of the projector.
• To avoid injury to yourself and damage to the
lamp, be sure to carefully follow the steps below.
• Do not loosen other screws except for the
lamp unit cover and lamp unit.
Press SSTANDBY/ON on the pro-
1
jector or aSTANDBY on the re­mote control to put the projector into standby mode.
• Wait until the cooling fan stops.
Disconnect the power cord.
2
• Unplug the power cord from the AC socket.
• Leave the lamp until it has fully cooled down (about 1 hour).
Optional
accessory
STANDBY/ON button
AC socket
Lamp unit AN-100LP
Remove the lamp unit cover.
3
• Turn the projector over. Loosen the user service screw (1) that secures the lamp unit cover. Remove the lamp unit cover (2).
1
2
User service screw (for lamp unit cover)
Appendix
55
Regarding the Lamp (Continued)
Remove the lamp unit.
4
• Loosen the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it.
Insert the new lamp unit.
5
• Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws.
Replace the lamp unit cover.
6
• Align the tab on the lamp unit cover (1) and place it while pressing the tab (2) to close it. Then tighten the user service screw to secure the lamp unit cover.
Info
• If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is con­nected to the projector.
Handle
Securing screws
2
1

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.
Info
• Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or ex­plode.
Connect the power cord.
1
• Plug the power cord into the AC socket of the projector.
Reset the lamp timer.
2
• While simultaneously holding down UMENU, TENTER and R on the pro­jector, press SSTANDBY/ON on the pro­jector.
• “LAMP 0000H” is displayed, indicating that the lamp timer is reset.
56
AC socket
STANDBY/ON button
ENTER button
MENU button
R button

Connecting Pin Assignments

COMPUTER-RGB/COMPONENT INPUT5 Terminal: 15-pin Mini D-sub female connector
COMPUTER-RGB Input
1. Video input (red)
2. Video input (green/sync on green)
11
1
15
5
6
RS-232C Terminal: 9-pin Mini DIN female connector
8
9
6
5
21
RS-232C Terminal: 9-pin D-sub male connector of the DIN-D-sub RS-232C adaptor
(optional accessory: AN-A1RS)
15
69
RS-232C Cable recommended connection: 9-pin D-sub female connector
51
96
3. Video input (blue)
4. Not connected
5. Not connected
6. Earth (red)
7. Earth (green/sync on green)
8. Earth (blue)
9. Not connected
10. GND
11. Not connected
10
12. Bi-directional data
13. Horizontal sync signal: TTL level
14. Vertical sync signal: TTL level
15. Data clock
Pin No.
7
3
4
Signal Name
1.
2.
3.
4.
5.
6.
7.
8.
9.
Signal NamePin No.
1.
2.
3.
4.
5.
6.
7.
8.
9.
SignalPin No.
1.
2.
3.
4.
5.
6.
7.
8.
9.
RD SD
SG
RS CS
RD SD
SG
RS CS
CD RD SD ER SG DR RS CS CI
Receive Data Send Data
Signal Ground
Request to Send Clear to Send
Receive Data Send Data
Signal Ground
Request to Send Clear to Send
I/O Reference
Input Output
I/O Reference
Input Output
1.
2.
3.
4.
5.
6.
7.
8.
9.
Component Input
1. PR (CR)
2. Y
B (CB)
3. P
4. Not connected
5. Not connected
6. Earth (P
7. Earth (Y)
8. Earth (P
9. Not connected
10. Not connected
11. Not connected
12. Not connected
13. Not connected
14. Not connected
15. Not connected
Not connected Connected to internal circuit Connected to internal circuit Not connected Connected to internal circuit Not connected Connected to CS in internal circuit Connected to RS in internal circuit Not connected
Not connected Connected to internal circuit Connected to internal circuit Not connected Connected to internal circuit Not connected Connected to CS in internal circuit Connected to RS in internal circuit Not connected
SignalPin No.
CD RD SD ER SG DR RS CS CI
R)
B)
Note
Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the controlling device (e.g. computer).
Projector
Pin No.
4 5 6
Computer
Pin No.
4 5 6
Appendix
57
Connecting Pin Assignments (Continued)
HDMI Terminal
119
218
NamePin No.
1.
TMDS Data2+
2.
TMDS Data2 Shield
3.
TMDS Data2-
4.
TMDS Data1+
5.
TMDS Data1 Shield
6.
TMDS Data1-
7.
TMDS Data0+
NamePin No.
TMDS Data0 Shield
8. TMDS Data0-
9. TMDS Clock+
10. TMDS Clock Shield
11. TMDS Clock-
12. CEC
13.
NamePin No.
Reserved
14. SCL
15. SDA
16. DDC/CEC Ground
17. +5V Power
18. Hot Plug Detect
19.

RS-232C Specifications and Command Settings

Computer control
A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type, sold separately) to the projector. (See page 27 for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table. Signal format: Conforms to RS-232C standard. Parity bit: None Baud rate: * 9,600 bps/115,200 bps Stop bit: 1 bit Data length: 8 bits Flow control: None * Set the projector's baud rate to the same rate as used by the computer.
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After the projector processes the command from the computer, it sends a response code to the computer.
Command format
C1 C2 C3 C4 P1 P2 P3 P4
Response code format
Command 4-digit
Normal response
OK
Parameter 4-digit
Return code (0DH)
Problem response (communication error or incorrect command)
Return code (0DH)
ERR
Return code (0DH)
Info
• When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds after the power has been turned on, and then transmit the commands.
• When more than one code is being sent, send each command only after the response code for the previous command from the projector is verified.
Commands
Example: When turning on the
projector, make the following setting.
CONTROL CONTENTS Power Off Power On INPUT 1 (Video1 : Component1) INPUT 2 (Video2 : Component2) INPUT 3 (Video3 : S-Video) INPUT 4 (Video4 : Video)
(RGB1 : RGB/Component)
INPUT 5 INPUT 6
(RGB2 : RGB/Component)
COMMAND PARAMETER
P
O
W
P
O
W
I
V
E
I
V
E
I
V
E
I
V
E
I
R
G
I
R
G
58
POWR _ 1__
RETURN R R D D D D
B B
OK or ERR
_
_
_
0
OK or ERR
_
_
_
1
OK or ERR
_
_
_
1
OK or ERR
_
_
_
2
OK or ERR
_
_
_
3
OK or ERR
_
_
_
4
OK or ERR
_
_
_
1
OK or ERR
_
_
_
2
→ ←
Note
• If an underbar (_) appears in the parameter column, enter a space.
ProjectorComputer
OK

Computer Compatibility Chart

Computer
• Multiple signal support Horizontal Frequency: 15-70 kHz, Vertical Frequency: 45-85 Hz, Pixel Clock: 12-85 MHz Sync signal: Compatible with TTL level
The following is a list of modes that conform to VESA. However, this projector supports other signals that are not VESA standards.
PC/MAC
PC
MAC 13"
MAC 16"
MAC 19"
VGA
SVGA
XGA
VGA
SVGA
XGA
Resolution
640 × 350
640 × 400
720 × 350
720 × 400
640 × 480
800 × 600
1,024 × 768
1,280 × 720 1,280 × 768
640 × 480 800 × 600 832 × 624
1,024 × 768
Horizontal Frequency
(kHz)
27.0
31.5
37.5
27.0
31.5
37.9
27.0
31.5
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
31.4
35.1
37.9
46.6
48.1
46.9
53.7
40.3
48.4
56.5
60.0
45.0
47.8
34.9
37.8
49.7
60.2
• Compatible with sync on green signal
• Expansion System resizing technology
Vertical Frequency
(Hz)
60 70 85 60 70 85 60 70 60 70 85 50 60 70 72 75 85 50 56 60 70 72 75 85 50 60 70 75 60 60 67 60 75 75
VESA
Standard
✔ ✔ ✔
✔ ✔
✔ ✔ ✔
✔ ✔ ✔
HDMI
Support
Display
Upscale
Upscale
Tru e
Tru e
Note
When this projector receives 640K350 VESA format VGA signals, “640K400” appears on the screen.
DTV
Signal
480I
480P
540P
576I
576P
720P
1035I
1035I
1080I
1080I
Horizontal Frequency (kHz)
15.7
31.5
33.8
15.6
31.3
45.0
28.1
33.8
28.1
33.8
Vertical Frequency (Hz)
60
60
60
50
50
60
50
60
50
60
HDMI Support
Appendix
59

Troubleshooting

Problem
Picure does not appear
or projector does not
start.
No picture appears (or
picture is dark).
Color is faded or poor.
Picture is blurred;
noise appears.
Picture is green on INPUT 5 (Component)/ INPUT 6 (Component).
Picture is pink (no green)
on INPUT 5 (RGB)/INPUT
6 (RGB).
An unusual sound is
occasionally heard from
the cabinet.
Maintenance indicator on
the projector illuminates
or blinks in red.
Check
• Projector power cord is not plugged into the wall outlet.
• Power to the external connected devices is off.
• The selected input mode is wrong.
• Cables incorrectly connected to the projector.
• Remote control battery has run out.
• External output has not been set when connecting notebook computer.
• The lamp unit cover is not installed correctly.
• Cables incorrectly connected to the projector.
• “Bright” is set to minimum position.
• Depending on the computer you are using, an image may not be projected unless the signal output setting of the computer is switched to the external output. Refer to the computer’s operation manual for how to switch its signal output settings.
• Image adjustments are incorrectly set.
• Make adjustments to “Color”, “Tint” and “BrilliantColor™” in “Picture Mode”.
(Video Input only)
• Video input system is incorrectly set.
• Adjust the focus.
• The projection distance exceeds the focus range.
• There is fog on the lens. If the projector is carried from a cold room into a warm room, or if it is suddenly heated, condensation may form on the surface of the lens and the image will become blurred. Please set up the projector at least one hour before it is to be used. If condensation should form, remove the power cord from the wall outlet and wait for it to clear.
(Computer Input only)
• Perform “Fine Sync” Adjustments (“Clock” Adjustment)
• Perform “Fine Sync” Adjustments (“Phase” Adjustment)
• Noise may appear depending on the computer.
• Select “Signal Type” in the “Options1” menu and change the input signal type.
• If the picture is normal, the sound is due to cabinet shrinkage caused by room temperature changes. This will not affect operation or performance.
• See “Maintenance Indicators”.
Page
28
29 23–27 14 26
55, 56 23–27 43
43
48
30 20
46 46
48
52
60
Problem
Picture is too bright and
whitish.
The black levels of the
image show banding or
appear faded when
INPUT 6 is selected.
The cooling fan becomes
noisy.
The lamp does not light
up even after the
projector turns on.
The lamp suddenly turns
off during projection.
The image sometimes
flickers.
The lamp needs much
time to turn on.
Picture is dark.
The remote control
cannot be used.
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation or interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes.
• Image adjustments are incorrectly set.
• Select the HDMI Setting (“Standard” or “Enhanced”) that results in the best picture quality.
• When temperature inside the projector increases, the cooling fan runs faster.
• The lamp indicator is illuminating in red. Replace the lamp.
• Cables incorrectly connected to the projector or the connected equipment works improperly.
• If this happens frequently, replace the lamp.
• The lamp will eventually need to be changed. While the remaining lamp life draws to a close, replace the lamp.
• Operate the remote control while pointing it at the projector’s remote control sensor.
• The remote control may be too far away from the projector.
• If direct sunlight or a strong fluorescent light is shining on the projector’s remote control sensor, place the projector where it will not be affected by strong light.
• The batteries may be depleted or inserted incorrectly. Make sure the batteries are inserted correctly or insert new ones.
Check
Page
43
48
52, 55
23-27
55 55
15
14
Appendix
61

Specifications

Product type
Model
Video system
Display method
DMD panel
Projection lamp
Component input signal
S-video input signal
Video input signal
Computer RGB/
Component input signal
HDMI input signal
Horizontal resolution
Vertical frequency
Horizontal frequency
RS-232C terminal
TRIGGER terminal
Rated frequency
Power consumption
Power consumption (standby)
Heat dissipation
Operating temperature
Storage temperature
I/R carrier frequency
Dimensions (approx.)
Weight (approx.)
Replacement parts
Lens
(INPUT1/2)
(INPUT 3)
(INPUT 4)
(INPUT 5)
(INPUT 6)
Pixel clock
Rated voltage
Input current
Cabinet
Projector XV-Z3000 NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAM/DTV480I/DTV480P/ DTV540P/DTV576I/DTV576P/DTV720P/DTV1035I/DTV1080I/DTV1080I-50 Single Chip Digital Micromirror DeviceTM (DMDTM) by Texas Instruments Panel size: 0.65", 1chip DMD Drive method: Digital Light Processing (DLP™) No. of dots: 983,040 dots (1280 [H] × 768 [V]) 1–1.15 × zoom lens, F2.4–2.6, f = 19.0–21.9 mm 275 W DC lamp RCA connector Y: 1.0 Vp-p, sync negative, 75 terminated PB (CB): 0.7 Vp-p, 75 terminated PR (CR): 0.7 Vp-p, 75 terminated 4-pin mini DIN connector Y (luminance signal): 1.0 Vp-p, sync negative, 75 terminated C (chrominance signal): Burst 0.286 Vp-p, 75 terminated RCA connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 terminated 15-pin mini D-sub connector RGB separate/sync on green type analog input: 0–0.7 Vp-p, positive, 75 terminated HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative) VERTICAL SYNC. SIGNAL: Same as above HDMI terminal (video signal only)
720 TV lines (DTV720P) 45–85 Hz 15–70 kHz 12–85 MHz 9-pin mini DIN connector Power jack: DC 12V output AC 100–240 V
3.7 A 50/60 Hz 355 W (Lamp Setting “Bright”)/ 310 W (Lamp Setting “Eco + Quiet”) 340 W (Lamp Setting “Bright”)/ 300 W (Lamp Setting “Eco + Quiet”) 4 W (AC 100 V) – 5 W (AC 240 V)* 1,335 BTU/hour (Lamp Setting “Bright”)/ 1,165 BTU/hour (Lamp Setting “Eco + Quiet”) with AC 100 V 1,280 BTU/hour (Lamp Setting “Bright”)/ 1,130 BTU/hour (Lamp Setting “Eco + Quiet”) with AC 240 V 41°F to 95°F (+5°C to +35°C) –4°F to 140°F (–20°C to +60°C) Plastic 38 kHz 12 13/32" × 4 19/64" × 11 1/32" (315 (W) × 109 (H) × 280 (D) mm) (main body only) 12 13/32" × 4 47/64" × 11 37/64" (315 (W) × 120 (H) × 294 (D) mm) (including adjust­ment foot and projecting parts)
8.8 lbs. (4.0 kg) Remote control, Power cord for Europe, except U.K., Power cord for U.K. and Singapore, Power cord for Australia, New Zealand and Oceania, 21 pin RCA conversion adaptor, Video cable, Operation manual
with AC 100 V
with AC 240 V
1
*1 When STANDBY Mode is set to “Eco”
As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specifica­tion figures indicated are nominal values of production units. There may be some deviations from these values in individual units.
62

Dimensions

Units: inches (mm)
13
1
23
19
7
(5)
64
/
(280)
32
/
11
(9)
64
/
(109)
64
/ 4
(11)
16
/
12 13/
ø9 7/
32
64
3
(315)
(69.2)
5
/
32
(80)
(47)
64
/
55
1
(73)
8
/
7
2
1
/
16
(77.5)
3
(104)
64
/
7
Appendix
(47.5) 4
8
/
7
1
(11)
16
/
11
1
/
32
2 61/
(75)
(33.8)
64
1
(46.2)
19
53
2
/
64
(65.5)
7
/
32
63

Index

AC socket ....................................................... 28
Accessories ................................................... 10
Adjustment buttons ........................................ 41
Aspect ratio .................................................... 36
Auto Power Off............................................... 49
Auto Sync
(Auto Sync adjustment) .............................. 46
AUTO SYNC button ....................................... 46
Background .................................................... 48
Backlight button .............................................13
Blue ................................................................ 43
Bright ............................................................. 43
BrilliantColor™ ............................................... 43
Checking the Input Signal ............................. 46
CINEMA ZOOM ...................................... 36, 37
Clock ..............................................................46
CLR Temp (Color Temperature) .................... 44
C.M.S. ............................................................44
Color .............................................................. 43
Contrast ......................................................... 43
DOT BY DOT .................................................37
DNR ............................................................... 45
ENTER button................................................41
Exhaust vent ........................................... 12, 51
Fan Mode ....................................................... 50
Fine Sync ....................................................... 46
Focus ring ......................................................30
FREEZE button ............................................. 38
GEOMETRIC ADJUSTMENT ....................... 34
H & V KEYSTONE .........................................35
HDMI Setting ................................................. 48
H-Pos ............................................................. 46
HEIGHT ADJUST lever ................................. 30
Hue ................................................................ 44
Image Shift .................................................... 47
IMAGE SHIFT buttons ................................... 38
INPUT 1 terminal ...........................................23
INPUT 1 – 6 modes .......................................29
INPUT 2 terminal ...........................................23
INPUT 3 terminal ...........................................24
INPUT 4 terminal ...........................................24
INPUT 5 terminal .................................... 25, 26
INPUT 6 terminal ...........................................25
INPUT buttons ...............................................29
Intake vent ........................................ 11, 12, 51
IRIS button ..................................................... 38
Kensington Security
Standard connector ............................. 12, 13
KEYSTONE button ........................................32
Keystone Correction ......................................32
Lamp ....................................................... 10, 54
Lamp indicator ...............................................52
Lamp Setting ................................................. 45
Lamp Timer (Life) .......................................... 49
Lamp unit .......................................................55
Language (on-screen display language) ...... 50
Lens cap ........................................................ 11
MENU button ................................................ 41
ON button ...................................................... 28
Optional accessories .....................................10
OSD Display .................................................. 48
Overscan ....................................................... 47
Phase ............................................................. 46
Picture Adjustment ........................................ 43
Picture Mode .......................................... 38, 43
PICTURE MODE button ................................38
Picture (Screen) Size and Projection Distance .......
Power cord ..................................................... 28
PRJ Mode ............................................... 19, 49
Progressive .................................................... 44
R-03 batteries ................................................14
Rear adjustment foot .....................................31
Red ................................................................ 43
Remote control .............................................. 13
Remote control sensor .................................. 15
Replacing the lamp ................................. 54, 55
Resize ..................................................... 36, 37
RESIZE button ............................................... 36
RETURN button ............................................. 41
RGB/COMP. button ........................................ 48
RS-232C Setting ............................................50
RS-232C terminal ..........................................27
Saturation ...................................................... 44
Sharp ............................................................. 43
SIDE BAR ............................................... 36, 37
Special Modes ...............................................46
STANDBY button ........................................... 29
STANDBY/ON button .............................. 28, 29
STANDBY Mode ............................................ 50
STRETCH ............................................... 36, 37
Subtitle ........................................................... 47
Supplied accessories .................................... 10
Temperature warning indicator......................52
Tint .................................................................43
TRIGGER terminal ........................................ 12
Value .............................................................. 44
Video System ................................................ 48
V-Pos .............................................................. 46
Zoom ring ....................................................... 30
20
64
Printed in China Gedruckt in China Imprimé en Chine Triykt i Kina Impreso en China Stampato in Cina Gedrukt in China TINS-C222WJN2 06P02-CH-NG
Loading...