Sharp XV-Z12000U User Manual

Page 1
XV-Z12000
PROJECTOR PROJECTEUR PROYECTOR PROJETOR
OPERATION MANUAL MODE D’EMPLOI MANUAL DE OPERACION MANUAL DE OPERAÇÃO
ENGLISH ............. -1 – -96
FRANÇAIS ........... -1 – -95
ESPAÑOL ............ -1 – -94
PORTUGUÊS ...... -1 – -94
Page 2
Before using the projector, please read this operation manual carefully.
Introduction
ENGLISH
IMPORTANT
For your assistance in reporting the loss or theft of your Projector, please record the Serial Number located on the bottom of the projector and retain this information. Before recycling the packaging, please be sure that you have checked the contents of the carton thoroughly against the list of “Supplied accessories” on page 14.
There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection, modification, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
Model No.: XV-Z12000
Serial No.:
U.S.A. ONLY
WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.
WARNING: To reduce the risk of fire or electric shock, do not expose this product to
rain or moisture.
Introduction
See bottom of actual set.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREWS.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
WARNING:
DO NOT REMOVE COVER.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equip­ment.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk or electric shock to persons.
The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
U.S.A. ONLY
-1
Page 3
INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
U.S.A. ONLY
Declaration of Conformity
SHARP PROJECTOR, MODEL XV-Z12000 This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Responsible Party:
SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430 TEL: 1-800-BE-SHARP (1-800-237-4277)
U.S.A. ONLY
WARNING:
The cooling fan in this projector continues to run for about 90 seconds after the projector enters the standby mode. During normal operation, when putting the projector into the standby mode always use the STANDBY button on the projector or on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord. DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
PRODUCT DISPOSAL
This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or, if you are located in the United States of America, the Electronic Industries Alliance: www.eiae.org .
Caution Concerning the Lamp Replacement
See Replacing the Lamp on pages 80-82.
BQC-XVZ100005
BQC-XVZ100005
BQC-XVZ100005
WARNING:
Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or discompile the contents thereof.
-2
Page 4
Contents
Introduction
Introduction
Contents............................................................... 3
IMPORTANT SAFEGUARDS............................... 5
How to Access the PDF Operation Manuals of
SharpVision Manager .................................... 8
Quick Guide ......................................................... 9
Part Names ........................................................ 10
Projector (Front and Top View) ................................ 10
Projector (Rear View) .............................................. 11
Remote Control (Front View)................................... 12
Remote Control (Top View) ..................................... 12
Using the Remote Control ................................ 13
Available Range of the Remote Control ................. 13
Inserting the Batteries .............................................13
Accessories ....................................................... 14
Connections and Setup
Connecting the Projector to Other Devices ... 16
Before Connecting.................................................. 16
Connecting the Power Cord ................................... 16
Connecting to Video Equipment.............................. 17
Connecting the Projector to a Computer ................. 22
Controlling the Projector by a Computer .................25
Using as a Wired Remote Control .......................... 26
Setup .................................................................. 27
Using the Adjustment Feet ..................................... 27
Adjusting the Lens .................................................. 28
Using the Lens Shift ................................................29
Setting up the Screen ..............................................30
Screen Size and Projection Distance ......................31
Projecting a Reversed/Inverted Image ................... 32
Basic Operation
Image Projection ............................................... 34
Basic Procedure ......................................................34
Selecting the On-screen Display Language ........... 36
Turning the Power off .............................................. 37
Keystone Correction and
Vertical Size Adjustment ............................. 38
Menu Bar Items ................................................. 40
Using the Menu Screen .................................... 42
Menu Selections (Adjustments) .............................. 42
Menu Selections (Settings) ..................................... 44
Adjusting the Picture ........................................ 46
Selecting the Picture Position ..................................46
Adjusting Image Preferences ..................................47
Selecting the Gamma Position ................................ 47
Selecting the C.M.S. Position .................................. 48
Special Settings ....................................................... 48
IP Mode .................................................................. 49
Emphasizing the Contrast ....................................... 50
Reducting Image Noise (DNR) ................................ 50
Emphasizing Outlines in the Image (DFC) ............. 51
Resetting All Adjustment Items .............................. 51
Adjusting the Gamma ....................................... 52
Selecting the Gamma Position ................................ 52
Adjusting the Gamma .............................................. 53
Color Management System (C. M. S.).............. 54
Selecting the C.M.S. Position .................................. 54
Selecting the Target Color ....................................... 54
Setting the Brightness of the Target Color ...............55
Setting the Chromatic Value of the Target Color...... 55
Setting the Hue of the Target Color ........................ 55
Resetting User-Defined Color Settings................... 56
Overview of All Color Settings ................................. 56
Adjusting Computer Images ............................ 57
When Auto Sync is OFF ........................................... 57
Saving Adjustment Settings ................................... 57
Selecting Adjustment Settings ................................ 58
Special Mode Settings ............................................58
Checking the Input Signal .......................................59
Auto Sync Adjustment .............................................59
Auto Sync Display Function ................................... 60
-3
Page 5
Contents
Easy to Use Functions
Selecting the Picture Display Mode ................ 62
Switchable High Brightness/High
Contrast Mode ............................................. 65
Digital Shift Function ........................................ 66
Subtitle Setting .................................................. 66
LED Off Function............................................... 67
Displaying the Lamp Usage Time .................... 67
Setting On-screen Display ............................... 68
Selecting the Signal Type................................. 69
Setting the Video System ................................. 70
Setting a Background Image............................ 70
Selecting the Economy Mode .......................... 71
Setting the Power Save ........................................... 71
RS-232C Off Function .............................................. 71
Automatic Power Off Function .................................72
Selecting the Transmission Speed
(RS-232C) ..................................................... 72
Reversing/Inverting Projected Images ............ 73
Displaying the Adjustment Settings................ 74
Appendix
Maintenance ...................................................... 76
Cleaning the Ventilative Holes ......................... 77
Maintenance Indicators .................................... 78
Regarding the Lamp ......................................... 80
Lamp ...................................................................... 80
Caution Concerning the Lamp ................................ 80
Replacing the Lamp ................................................80
Removing and Installing the Lamp Unit ................. 81
Resetting the Lamp Timer ....................................... 82
Connecting Pin Assignments .......................... 83
(RS-232C) Specifications and
Command Settings ...................................... 84
Wired Remote Control Terminal
Specifications .............................................. 87
Computer Compatibility Chart ......................... 88
Troubleshooting ................................................ 89
For SHARP Assistance (U.S.A only) ................ 90
Specifications .................................................... 91
Dimensions ........................................................ 92
Glossary ............................................................. 93
Index ................................................................... 94
-4
Page 6
IMPORTANT SAFEGUARDS
CAUTION: Please read all of these instructions before you operate this product and save them for
later use.
Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing.
Introduction
1. Read Instructions
All the safety and operating instructions should be read before the product is operated.
2. Retain Instructions
The safety and operating instructions should be retained for future reference.
3. Heed Warnings
All warnings on the product and in the operating instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.
8. Accessories
Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturers instructions, and should use a mounting accessory recommended by the manufacturer.
9. Transportation
A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a book­case or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
11. Power Sources
This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
12. Grounding or Polarization
This product is equipped with a three-wire grounding­type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.
13. Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
14. Lightning
For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the product due to lightning and power-line surges.
15. Overloading
Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
17. Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to dan­gerous voltage or other hazards. Refer all servicing to qualified service personnel.
-5
Page 7
IMPORTANT SAFEGUARDS
18. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen
into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions, as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to normal operation. e. If the product has been dropped or damaged in
any way. f. When the product exhibits a distinct change in
performance.
19. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
20. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
21. Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling only as recommended by the manufacturer.
22. Heat
This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
INTELLECTUAL PROPERTY RIGHTS
IMPORTANT
READ BEFORE USING THE PRODUCT
Digital Light Processing, DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments.
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or
other countries.
PC/AT is a registered trademark of International Business Machines Corporation in the United States.
Adobe Acrobat is a trademark of Adobe Systems Incorporated.
Macintosh is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.
All other company or product names are trademarks or registered trademarks of their respective compa-
nies.
-6
Page 8
Be sure to read the following safeguards when setting up your projector.
Caution concerning the lamp unit
Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest Authorized SharpVision Service Center or Dealer for replacement. See Replacing the Lamp” on pages 80-82.
CAUTION PRECAUCIÓN PRÉCAUTION
BQC-XVZ100005
Cautions concerning the setup of the projector
For minimal servicing and to maintain high image qual­ity, SHARP recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environments, the lens must be cleaned more often. As long as the projector is regularly cleaned, use in these environ­ments will not reduce the overall operation life of the unit. Internal cleaning should only be performed by an Authorized SharpVision Service Center or Dealer.
Do not set up the projector in places exposed to direct sunlight or bright light.
Position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the cur­tains and dim the lights when setting up the screen in a sunny or bright room.
The projector may safely be tilted to a maximum angle of 5 degrees.
Placement should be within ±5 degrees.
Do not subject the projector to hard impact and/ or vibration.
Take care with the lens so as not to hit or damage the surface of the lens.
Rest your eyes occasionally.
Watching the screen for long hours continuously will make your eyes tired. Be sure to occasionally rest your eyes.
Avoid locations with high or low temperature.
The operating temperature for the projector is from 41°F to 95°F (+5°C to +35°C).
The storage temperature for the projector is from –4°F to 140°F (–20°C to +60°C).
Be sure that the intake vent and the exhaust vent are not obstructed.
If the cooling fan becomes obstructed, a protection cir­cuit will automatically put the projector into the standby mode. This does not indicate a malfunction. Remove the projector power cord from the wall outlet and wait at least 10 minutes. Place the projector where the in­take and exhaust vents are not blocked, plug the power cord back in and turn on the projector. This will return the projector to the normal operating condition.
Cautions regarding the transportation of the pro­jector
When transporting the projector, be sure not to subject it to hard impact and/or vibration, as this can result in damage. Take extra caution with the lens. Before mov­ing the projector, be sure to unplug the power cord from the wall outlet, and disconnect any other cables con­nected to it.
Other connected equipment
When connecting a computer or other audio-visual equipment to the projector, make the connections AF­TER unplugging the power cord of the projector from the AC outlet and turning off the equipment to be con­nected.
Please read the operation manuals of the projector and the equipment to be connected for instructions on how to make the connections.
Temperature monitor function
If the projector starts to overheat due to setup problems or blockage of the air vents, and will blink in the lower left corner of the picture. If the tem­perature continues to rise, the lamp will turn off, the temperature warning indicator on the projector will blink, and after a 90-second cooling-off period the projector will enter the standby mode. Refer to Maintenance In­dicators on page 78 for details.
Info
The cooling fan regulates the internal temperature, and its performance is automatically controlled. The sound of the fan may change during projector operation due to changes in the fan speed. This does not indicate malfunction.
Do not unplug the power cord during projection or cool­ing fan operation. This can create damage due to the rise in internal temperature, as the cooling fan also stops.
Introduction
Do not block the intake and exhaust vents.
Allow at least 11.8" (30 cm) of space between the ex­haust vent and the nearest wall or obstruction.
-7
Page 9
How to Access the PDF Operation Manuals of SharpVision Manager
PDF operation manuals in several languages for the “SharpVision Manager” theater projec­tor software provided are included in the CD-ROM. To utilize these manuals, you need Adobe Acrobat Reader installed on your PC (Windows or Macintosh). If you have not installed Acro­bat Reader yet, you can install it from the CD-ROM.
To install Acrobat Reader from the CD-ROM
For Windows:
1 Insert the CD-ROM in the CD-ROM drive. 2 Start up Explore. 3 Double click the “CD-ROM” drive. 4 Double click the “ACROBAT” folder. 5 Double click the language (name of the folder)
that you want to view.
6 Double click the installation program and
follow the instructions on the screen.
For other operating systems:
Please download Acrobat Reader from the Internet (http://www.adobe.com).
For other languages:
If you prefer using Acrobat Reader for languages other than those included in the CD-ROM, please download the appropriate version from the Internet.
For Macintosh:
1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the “CD-ROM” icon. 3 Double click the “ACROBAT” folder. 4 Double click the language (name of the folder)
that you want to view.
5 Double click the installation program and
follow the instructions on the screen.
Accessing the PDF Manuals
For Windows:
1 Insert the CD-ROM in the CD-ROM drive. 2 Start up Explore. 3 Double click the “CD-ROM” drive. 4 Double click the “MANUALS” folder. 5 Double click the language (name of the
folder) that you want to view.
6 Double click the “SVM2” pdf file to access the
SharpVision Manager manual.
Note
The installer of SharpVision Manager may start automatically when the CD-ROM is inserted in the CD-
ROM drive of the Windows PC. In this case, stop installation by clicking on Cancel”.
If the desired pdf file cannot be opened by double clicking the mouse, start Acrobat Reader first, then
specify the desired file using the File, Open menu.
See the “readme.txt file on the CD-ROM for important information not included in this operation manual.
For Macintosh:
1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the CD-ROM icon. 3 Double click the MANUALS folder. 4 Double click the language (name of the
folder) that you want to view.
5 Double click the “SVM2 pdf file to access the
SharpVision Manager manual.
-8
Page 10
Quick Guide
In this page, connection of the projector and the video equipment is explained as an example for the procedure from setup to projection. Refer to each page for details.
○○○○○○○○○○○○○
Required equipments
Projector Remote control
Power cord
Insert the batteries.
(Page 13)
Video equipment
Composite video cable
(commercially available)
Introduction
1. Place the projector facing a wall or a screen.
2. Connect to video equipment. (Page 17)
Composite video cable (commercially available)
To INPUT 4 terminal
To video out­put terminal
3. Connect the output terminal of the video equip­ment to the input terminal of the audio equip­ment using an audio cable.
4. Plug the power cord into the AC socket of the projector and into the wall outlet. (Page 16, 34)
5. Remove the lens cap from the lens. (Page 10)
6. Turn the projector on using on the remote control. (Page 34)
INPUT 4 button
7. Press
ON button
The power indicator illuminates blue.
on the remote control to select the
INPUT 4 mode. (Page 35)
"On-screen Display
8. Turn on the video equipment.
ON
9. Play the video.
10
. Adjust the image size, image position and the
focus. (Page 28, 29)
Adjust the focus by rotating the focus ring.
Adjust the zooming by moving the zoom knob.
Power cord
Lens cap
Adjust the height of the image by rotating the lens shift dial.
Note
This projector can also be connected to a computer
as well as to video equipment. (Page 22)
-9
Page 11
Part Names
Numbers in refer to the main pages in this operation manual where the topic is explained.
Projector (Front and Top View)
Adjustment buttons
For selecting menu items.
For setting items selected
or adjusted on the menu.
For undoing an operation or
(", ', \, |)
ENTER button
UNDO button
returning to the default
Lens shift dial
Zoom knob
settings.
29
28
43
43
43
MENU button
42
For displaying adjustment and setting screens.
RESIZE button
62
For switching the screen size (SIDE BAR, SMART STRETCH, etc.).
INPUT button
35
For switching input mode 1, 2, 3, 4 or 5.
ON button
34
For turning the power on.
STANDBY button
37
For putting the projector into the standby mode.
78
Temperature warning indicator
When the internal temperature rises, this indicator will illuminate red.
Lamp indicator
78
Illuminates blue, indicating normal function. Replace the lamp when the indicator illuminates red.
Focus ring
Adjustment foot
Lens cap
28
27
Attaching and removing the lens cap
Press on the two buttons of the lens cap and attach it on the lens. Then release the buttons to lock it in place.
Press on the two buttons of the lens cap and remove it from the lens.
-10
Power indicator
34
Illuminates red, when the projector is in standby. When the power is turned on, this indicator will illuminate blue.
Intake vent
27
Adjustment foot
13
Remote control sensor
In this operation manual, the illustration and the screen display are simplified for explanation, and may differ slightly from actual display.
Page 12
PUSH!
3
Projector (Rear View)
INPUT 3 terminal
17
Terminal for connecting video equipment with an S-video terminal.
Introduction
INPUT 1 terminals
Terminals for
component and
RGB signals
INPUT 5 terminal
Terminal for DVI
digital, computer
RGB and component
signals.
INPUT 2 terminals
Terminals for
component and RGB
signals
AC socket
Intake vent
18
.
19
RS-232C terminal
25
For controlling projector using a computer.
DC 12V OUTPUT terminal
WIRED REMOTE
26
control input terminal
18
.
INPUT 4 terminal
17
For connecting
16
video equipment.
Intake vent
77
77
Kensington Security
Standard connector
Exhaust vent
Remote control
sensor
77
13
Rubber cap
The terminal cover can be attached after removing the rubber cap.
Using the Kensington Lock
This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security Sys­tem. Refer to the information that came with the system for instructions on how to use it to secure the projector.
Using the Terminal Cover
When the projector is used on a desktop, high mounted or ceiling mounted, attach the terminal cover (supplied) to hide the connecting cables.
Attaching the Terminal Cover
1 Align the hook on the terminal cover with the insert hole
in the hook at the back of the projector.
2 Press the hook in the direction indicated with the arrow to
fasten the terminal cover to the projector.
3 Insert the terminal cover into the mounting groove on the
projector while pushing the tabs inside the terminal cover
1
Removing the rubber cap attached on the pro­jector and attach the clips.
1
2
to the outside with your fingers.
3
-11
Page 13
Part Names
Remote Control (Front View)
For putting the projector into the
STANDBY button
standby mode.
KEYSTONE button
For adjusting Keystone Correction
or Vertical Size setting.
ENTER button
For setting items selected or
adjusted on the menu.
UNDO button
For undoing an operation or
returning to the default settings.
AUTO SYNC button
For automatically adjusting images
when connected to a computer.
RGB/COMP. button
For switching to the respective
input signal type.
37
38
43
43
59
69
ON button
34
For turning the power on.
MENU button
42
For displaying adjustment and setting screens.
Adjustment buttons
43
(", ', \, |)
For selecting menu items.
35
INPUT buttons
For switching to the respective input modes.
RESIZE button
62
For switching the screen size (SIDE BAR, SMART STRETCH, etc.).
PICTURE POSITION button
46
For selecting the picture position.
Remote Control (Top View)
Remote control signal transmitters
-12
13
IRIS button
65
For switching “HIGH BRIGHTNESS MODE, MEDIUM MODE and HIGH CONTRAST MODE.
Backlight button
For lighting all buttons on the remote control.
WIRED R/C JACK
26
For controlling the projector by connecting the remote control to the projector.
Page 14
Using the Remote Control
Available Range of the Remote Control
The remote control can be used to control the projector within the ranges shown in the illustration.
Note
The signal from the remote control can be reflected off a screen
for easy operation. However, the effective distance of the signal may differ due to the screen material.
Remote control
23'(7 m)
45˚
30˚
30˚
Introduction
When using the remote control:
Be sure not to drop, expose to moisture or high temperature.
The remote control may malfunction under a fluorescent lamp.
Under that circumstance, move the projector away from the fluo­rescent lamp.
Inserting the Batteries
The batteries (two AA size) are included in the package.
1 Pull down the tab on the cover
and remove the cover towards the direction of the arrow.
2 Insert the included batteries.
Insert the batteries making sure the polarities correctly match the
marks inside the battery
compartment.
and
3 Insert the lower tab of the
cover into the opening, and lower the cover until it clicks in place.
45˚
30˚
Remote control
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.
Caution
Insert the batteries making sure the polarities correctly match the and marks inside the battery compart­ment.
Batteries of different types have different properties, therefore do not mix batteries of different types.
Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
Remove the batteries from the remote control once they have run out, as leaving them can cause them to leak. Battery fluid from leaked batteries is harmful to your skin, therefore be sure to first wipe them and then remove them using a cloth.
The batteries included with this projector may exhaust over a short period, depending on how they are kept. Be sure to replace them as soon as possible with new batteries when they have run out.
Remove the batteries from the remote control if you will not be using the remote control for a long time.
-13
Page 15
Accessories
Supplied accessories
Remote control RRMCGA216WJSA
Lens cap (attached) PCAPH1056CESA
Two AA size batteries
CD-ROM (SharpVision Manager) UDSKAA040WJZZ
Power cord CACCDA024DE01
Terminal cover CCOVA1985CE03
Operation manual (this manual) TINS-A970WJZZ
SharpVision Manager operation manual TINS-B097WJZZ
Optional accessories
3 RCA to 15-pin D-sub cable (9'10'' (3.0 m)) AN-C3CP DVI to 15-pin D-sub adaptor (7.9'' (20 cm)) AN-A1DV DVI cable (9'10'' (3.0 m)) AN-C3DV
Note
Some of the cables may not be available depending on the region. Please check with your nearest Authorized SharpVision Service Center or Dealer.
-14
Page 16
Connections and Setup
Connections and Setup
Page 17
Connecting the Projector to Other Devices
Before Connecting
Note
Before connecting, be sure to unplug the power cord of the projector from the AC outlet and turn off the devices to be connected. After making all connections, turn on the projector and then the other devices. When connecting a computer, be sure that it is the last device to be turned on after all the connec­tions are made.
Be sure to read the operation manuals of the devices to be connected before making connections.
This projector can be connected to:
Video equipment:
A VCR, DVD player or other video equipment (See page 17.)
A DVD player or DTV* decoder (See page 18.)
*DTV is the umbrella term used to describe the new digital television system in the United States.
A computer using:
DVI to 15-Pin D-sub adapter (See page 22.)
A DVI cable (See page 23.)
An RS-232C cable (See page 25.)
Connecting the Power Cord
Plug in the supplied power cord into the AC socket on the rear of the pro­jector.
Supplied accessory
Power cord
-16
-16
Power cord
Page 18
Connecting to Video Equipment
Connecting to Video Equipment Using an S-video or a Composite Video Cable (INPUT 3 or 4)
Using an S-video or a composite video cable, a VCR, DVD player or other video equipment can be connected to INPUT 3 or INPUT 4 input terminal.
1 Connect an S-video cable or a
composite video cable to the projector.
S-video cable: to INPUT 3 terminal
Composite video cable: to INPUT 4
terminal
2 Connect the above cable to the
video equipment.
S-video cable: to S-video output ter­minal
Composite video cable: to video out­put terminal
S-video cable (commercially available) *Use when connecting to video
equipment with S-video output terminal.
Composite video cable (commercially available) *Use when connecting to video equipment
without S-video output terminal.
To video output terminal
Connections and Setup
To INPUT 3 terminal
To INPUT 4 terminal
To S-video output terminal
Note
The INPUT 3 (S-VIDEO) terminal uses a video signal system in which the picture is separated into color and luminance sig­nals to realize a higher-quality image. To view a higher-quality image, use a com­mercially available S-video cable to con­nect the INPUT 3 terminal on the projec­tor and the S-video output terminal on the video equipment.
VCR or other video equipment
-17
Page 19
Connecting the Projector to Other Devices
Connecting to Component Video Equipment Using a Component Cable (INPUT 1 or 2)
Use a component cable when connecting the component video equipment such as DVD play­ers and DTV* decoders to INPUT 1 or 2 termi­nals.
*
DTV is the umbrella term used to describe the new digital television system in the United States.
1 Connect a component cable to
the projector.
2 Connect the above cable to the
component video equipment.
To INPUT 1 or 2 terminals
Component cable
(commercially available)
Note
When connecting the projector to the video equipment in this way, select Com­ponent for Signal Type in the Options menu, or select the Component mode by pressing page 69.
Set the “Resolution of Special Modes to 480P during input of a 480P signal. See page 58.
on the remote control. See
To analog component output terminal
DVD player or DTV* decoder
-18
Page 20
Connecting to RGB Video Equipment Using a 5 RCA RGB Cable (INPUT 1 or 2)
Use a 5 RCA RGB cable when connecting the RGB video equipment such as DVD players and DTV* decoders to INPUT 1 or 2 terminals. *
DTV is the umbrella term used to describe the new digital television system in the United States.
1 Connect a 5 RCA RGB cable to
the projector.
2 Connect the above cable to the
RGB video equipment.
Note
When connecting the projector to the video equipment in this way, select “RGB” for “Signal Type” in the “Options” menu, or select the RGB mode by pressing on the remote control. See page 69.
The (HD/C sync) and (VD) terminals may be used depending on the specifications of the DTV decoder connected to this pro­jector. Please refer to the operation manual of the DTV decoder for details.
To INPUT 1 or 2 terminals
Connections and Setup
5 RCA RGB cable
(Commercially available)
To analog RGB output terminal
DVD player or DTV* decoder
Connecting to RGB Video Equipment Using the DVI to 15-pin D-sub Adaptor and the RGB Cable (INPUT 5)
1 Connect a DVI to 15-pin D-sub
adaptor to the projector.
2 Connect the above adaptor to
an RGB cable.
3 Connect the above cable to the
RGB video equipment.
Secure the connectors by tightening the thumbscrews.
Note
When connecting the projector to the video equipment in this way, select A. RGB for Signal Type in the Options menu, or se­lect the A. RGB mode by pressing the remote control. See page 69.
on
Optional accessory
To INPUT 5 terminal
DVI to 15-pin D-sub adaptor (sold separately)
(commercially available)
To RGB output terminal
DVI to 15-pin D-sub adaptor Type: AN-A1DV (7.9" (20 cm))
RGB Cable
DVD player or DTV* decoder
-19
Page 21
Connecting the Projector to Other Devices
Connecting to Compo­nent Video Equipment Using a 3 RCA to 15-pin
Optional accessories
D-sub Cable and the DVI to 15-pin D-sub Adaptor (INPUT 5)
Use a 3 RCA to 15-pin D-sub cable and the DVI to 15-pin D-sub adaptor when connecting component video equipment such as DVD players and DTV* decoders to the INPUT 5 ter­minal.
*
DTV is the umbrella term used to describe the new digital television system in the United States.
To INPUT 5 terminal
1 Connect a DVI to 15-pin D-sub
adaptor to the projector.
3 RCA to 15-pin D-sub cable Type: AN-C3CP (9'10" (3.0 m))
DVI to 15-pin D-sub adaptor Type: AN-A1DV (7.9" (20 cm))
2 Connect a 3 RCA to 15-pin D-
sub cable to the above adaptor.
Secure the connectors by tightening the thumbscrews.
3 Connect the above cable to the
video equipment.
Note
Select the input signal type of the video equipment. See page 69.
DVI to 15-pin D-sub adaptor (sold separately)
3 RCA to 15-pin
D-sub cable
(sold separately)
To analog component
output terminal
DVD player or DTV* decoder
-20
-20
Page 22
Connecting to Video Equipment with the HDMI Output Terminal Using a DVI to HDMI Cable (INPUT 5)
Use a DVI to HDMI cable when connecting HDMI video equipment such as DVD players to INPUT 5 terminal.
1 Connect a DVI to HDMI cable
to the projector.
Secure the connectors by tightening the thumbscrews.
To INPUT 5 terminal
Connections and Setup
2 Connect the above cable to the
video equipment.
Note
Select the input signal type of the video equipment. See page 69.
Before connecting, be sure to unplug the power cord of the projector from the AC outlet and turn off the devices to be con­nected. After making all connections, turn on the projector and then the other devices.
Connecting to Video Equipment with the DVI Output Terminal Using a DVI Cable (INPUT 5)
Use a DVI cable when connecting video equip­ment with the DVI output terminal such as DVD players to INPUT 5 terminal.
1 Connect a DVI cable to the pro-
jector.
DVI to HDMI cable (commercially available)
Video equipment
Optional accessory
To INPUT 5 terminal
To HDMI output terminal
DVI cable
AN-C3DV
Type:
(9'10'' (3.0 m))
2 Connect the above cable to the
video equipment.
Secure the connectors by tightening the thumbscrews.
Note
Select the input signal type of the video equipment. See page 69.
Before connecting, be sure to unplug the power cord of the projector from the AC outlet and turn off the devices to be con­nected. After making all connections, turn on the projector and then the other devices.
DVI cable (sold separately)
To DVI Digital output terminal
Video equipment
-21
Page 23
Connecting the Projector to Other Devices
Connecting the Projector to a Computer
Connecting to a Computer Using the DVI to 15-pin D-sub Adaptor and the RGB Cable (INPUT 5)
1 Connect a DVI to 15-pin D-sub
adaptor to the projector.
2 Connect the above adaptor to
an RGB cable.
3 Connect the above cable to the
computer.
Secure the connectors by tightening the thumbscrews.
Note
See “Computer Compatibility Chart on page 88 for a list of computer signals compatible with the projector. Use with computer signals other than those listed may cause some of the functions not to work.
When connecting the projector to a com­puter in this way, select A. RGB for Sig­nal Type in the Options menu, or select the A. RGB by pressing mote control. See page 69.
A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Authorized SharpVision Service Center or Dealer.
Depending on the computer you are us­ing, an image may not be projected un­less the signal output setting of the com­puter is switched to the external output. Refer to the computer operation manual for switching the computer signal output settings.
on the re-
Optional accessory
To INPUT 5 terminal
DVI to 15-pin D-sub adaptor (sold separately)
(commercially available)
DVI to 15-pin D-sub adaptor Type: AN-A1DV (7.9" (20 cm))
RGB Cable
To RGB output terminal
Notebook computer
-22
-22
Page 24
Connecting to a Com­puter Using a DVI Cable (INPUT 5)
1 Connect a DVI cable to the pro-
jector.
Optional accessory
DVI cable
AN-C3DV
Type:
(9'10'' (3.0 m))
2 Connect the above cable to the
computer.
Secure the connectors by tightening the thumbscrews.
Note
Switch the signal type to either “A. RGB or D. PC RGB depending on whether the computer output signal is analog or digi­tal. See page 69.
Before connecting, be sure to unplug the power cord of the projector from the AC outlet and turn off the computer to be con­nected. After making all connections, turn on the projector and then the computer.
Be sure that the computer is the last de­vice to be turned on after all the connec­tions are made.
Connections and Setup
To INPUT 5 terminal
DVI cable (sold separately)
To DVI Digital output terminal
Desktop computer
-23
Page 25
Connecting the Projector to Other Devices
Connecting the thumbscrew cables
Connect the thumbscrew cable making sure that it fits cor-
rectly into the terminal. Then, firmly secure the connec­tors by tightening the screws on both sides of the plug. Do not remove the ferrite core attached to the RGB cable.
Ferrite core
Plug and Play function
This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC
compatible computer will communicate their setting requirements, allowing for quick and easy setup.
Before using the “Plug and Play function, be sure to turn on the projector first and the con-
nected computer last.
Note
The DDC “Plug and Play function of this projector operates only when used in conjunction with a VESA DDC compatible computer.
-24
Page 26
Controlling the Projector by a Computer
Controlling the Projector Using an RS-232C Cable
When the RS-232C terminal on the projector is connected to a computer with an RS-232C cable (null modem, cross type, commercially available), the computer can be used to con­trol the projector and check the status of the projector. See page 84 for details.
Connections and Setup
1 Connect an RS-232C cable to
the projector.
2 Connect the above cable to the
computer.
Secure the connectors by tightening the thumbscrews.
Note
Do not connect or disconnect an RS-232C cable to or from the computer while it is on. This may damage your computer.
The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the operation manual of the computer for details.
To RS-232C terminal
RS-232C cable
(commercially available)
To RS-232C terminal
Desktop computer
-25
Page 27
Connecting the Projector to Other Devices
Using as a Wired Remote Control
Connecting the Remote Control to the Projector
When the remote control cannot be used due to the range or positioning of the projector (rear projection, etc.), connect a ø3.5 mm minijack cable (commercially available or available as Sharp service part QCNWGA038WJPZ) from the WIRED R/C JACK on the top of the remote control to the WIRED REMOTE control input terminal.
To WIRED REMOTE control input terminal
Remote control
ø3.5 mm minijack cable (commercially available or available as Sharp service part QCNWGA038WJPZ)
To WIRED R/C JACK
-26
Page 28
Setup
Using the Adjustment Feet
The height of the projector can be adjusted using the adjustment feet when the projector is placed on an uneven surface or when the screen is slanted. The position of the projected image can be made higher by adjusting the projector when it is in a location lower than the screen.
1 Press the foot releases and lift
the projector to the desired angle.
2 Remove your hands from the
foot releases. Once the adjust­ment feet have locked in posi­tion, release the projector.
If the screen is at an angle, the ad­justment feet can be used to adjust the angle of the image.
Connections and Setup
Foot releases
Note
The projector is adjustable up to approxi­mately 5 degrees from the standard posi­tion.
When the height of the projector is ad­justed, the image may become distorted (keystoned), depending on the relative positions of the projector and the screen. See page 38 for details on the keystone correction.
Info
Do not hold the lens when lifting or lower­ing the projector.
When lowering the projector, be careful not to get your finger caught in the area between the adjustment foot and the projector.
Adjustment feet
-27
Page 29
Setup
Adjusting the Lens
The image is focused and adjusted to the desired size using the focus ring or zoom knob on the projector.
1 The focus is adjusted by rotat-
ing the focus ring.
2 Zooming is adjusted by mov-
ing the zoom knob.
Focus ring
Focus ring
Zoom knob
Zoom in
Zoom Knob
Zoom out
-28
Page 30
Using the Lens Shift
The height of the projected image can be ad­justed within the shift range of the lens by rotating the lens shift dial on the top of the projector.
Note
Do not turn the lens shift dial beyond the upper limit and lower limit positions. This may cause the projector to malfunction.
Lens shift dial
Up
Down
Connections and Setup
-29
Page 31
Setup
Setting up the Screen
Position the projector perpendicular to the screen with all feet flat and level to achieve an optimal image.
Note
The projector lens should be centered in the middle of the screen. If the horizontal line passing through the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
For optimal image, position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.
A polarizing screen cannot be used with this projector.
Standard Setup (Front Projection)
Place the projector at the required distance from the screen according to the desired picture size. (See
page 31.) Screen size : 100 inches (254 cm) Aspect ratio : 16:9
Example of Standard Setup
Side View
90°
Top View
90°
Audience
The distance from the screen to the projector
may vary depending on the size of the screen.
P. 31
The default setting can be used, when placing the
projector in front of the screen. If the projected im­age is reversed or inverted, readjust the setting to Front for PRJ Mode in the Options menu.
P. 73
Place the projector so that an imaginary horizontal
line that passes through the center of the lens is perpendicular to the screen.
-30
Page 32
Screen Size and Projection Distance
y
z
When using a normal screen (4:3)
In case of setting the 16:9 picture to the full horizontal width of the 4:3 screen.
4
3
: Screen area : Picture area
Screen size (4:3)
Diag. (x)
250" 200" 150" 100"
84" 72" 60"
Width
200" 160" 120"
80" 67" 58" 48"
Height
150" 120"
90" 60" 50" 43" 36"
The formula for screen size and projection distance
(Max.) = (0.05058x – 0.0447) × 3.28
y
1
(Min.) = (0.03734x – 0.0447) × 3.28
y
2
z1 (Upper) = 0
(Lower) = 0.45x
z
2
Projection distance (y)
Maximum (y1)
41'4" (12.6 m)
33' (10.1 m) 24'9" (7.5 m) 16'5" (5.0 m) 13'9" (4.2 m)
11'10" (3.6 m)
9'10" (3.0 m)
x
Distance from the lens center to the lower edge of the screen (z)
Minimum (y2) 30'6" (9.3 m) 24'4" (7.4 m) 18'3" (5.6 m) 12'1" (3.7 m) 10'2" (3.1 m)
8'8" (2.6 m) 7'2" (2.2 m)
Upper (z1)
0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm)
Lower (z2)
12'6" (286 cm)
10' (229 cm)
7'6" (171 cm)
5' (114 cm)4'2" (96 cm)3'7" (82 cm)
3' (69 cm)
x : Screen size (diag.) (inches) y : Projection distance (feet) z : Distance from the lens center to the
lower edge of the screen (feet)
Connections and Setup
When using a wide screen (16:9)
In case of displaying the 16:9 picture on the whole of the 16:9 screen.
16
9
: Picture area
Note
There is an error of ±3% in the formula above.
Values with a minus (–) sign indicate the distance of the lens center below the
bottom of the screen.
Screen size (16:9) Projection distance (y)
Diag. (x)
300" 250" 200" 150" 133" 106" 100"
92" 84" 72" 60" 40"
Width
261" 218" 174" 131" 116"
92" 87" 80" 73" 63" 52" 35"
Height
147" 123"
98" 74" 65" 52" 49" 45" 41" 35" 29" 20"
Maximum (y1) 54'1" (16.5 m) 45'1" (13.7 m)
36' (11.0 m) 26'12" (8.2 m) 23'11" (7.3 m) 18'11" (5.8 m) 17'11" (5.5 m)
16'5" (5.0 m)
15' (4.6 m)
12'10" (3.9 m)
10'8" (3.3 m)
7'1" (2.2 m)
Minimum (y2)
39'11" (12.2 m)
33'3" (10.1 m)
26'7" (8.1 m)
19'11" (6.1 m)
17'7" (5.4 m)
13'11" (4.3 m)
13'2" (4.0 m) 12'1" (3.7 m) 11'1" (3.4 m)
9'6" (2.9 m)
7'10" (2.4 m)
5'2" (1.6 m)
Distance from the lens center to the lower edge of the screen (z)
Upper (z1)
0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm)
Lower (z2)
12'3" (374 cm)10'3" (311 cm)
8'2" (249 cm)6'2" (187 cm)5'5" (166 cm)4'4" (131 cm)4'1" (125 cm)3'9" (114 cm)3'5" (105 cm)2'11" (90 cm)
2'5" (75 cm)1'8" (50 cm)
The formula for screen size and projection distance y1 (Max.) = (0.05510x – 0.04593) × 3.28
(Min.) = (0.04068x – 0.04369) × 3.28
y
2
(Upper) = 0
z
1
z2 (Lower) = –0.4904x
x : Screen size (diag.) (inches) y : Projection distance (feet) z : Distance from the lens center to the
lower edge of the screen (feet)
Note
There is an error of ± 3% in the formula above.
Values with a minus (–) sign indicate the distance of the lens center below the
bottom of the screen.
-31
Page 33
Setup
Projecting a Reversed/Inverted Image
Projection from behind the screen
Place a translucent screen between the projector and the au­dience.
Reverse the image by setting Rear for PRJ Mode in theOptions menu. See
page 73 for use of this function.
Projection using a mirror
Place a mirror (normal flat type) in front of the lens.
When using the default setting.
On-screen Display
The image is reversed.
Info
When using a mirror, be sure to carefully position both the pro-
jector and the mirror so the light does not shine into the eyes of the audience.
Ceiling-mount setup
It is recommended that you use the optional Sharp ceiling-mount bracket for this installation.
Before mounting the projector, contact your nearest Authorized SharpVision Service Center or Dealer to obtain the recommended ceiling-mount bracket (sold separately). (AN­CM250 ceiling-mount bracket, AN-EP101B extension tube for AN-CM250.)
Be sure to adjust the position of the projector to match the distance (z) from the lens center position (see page 31) to the lower edge of the image, when mounting the projec­tor on the ceiling.
Invert the image by setting Ceiling + Front for PRJ Mode in the Options menu. See page 73 for use of this function.
When using the default setting.
On-screen Display
The image is inverted.
-32
Page 34
Basic Operation
Basic Operation
Page 35
Image Projection
Basic Procedure
Connect the required external equipment to the projector before operating the following procedures.
Info
The language preset at the factory is English. If you want to change the on-screen display to another language, reset the language ac-
36
cording to the procedure on page
.
1 Plug the power cord into the
wall outlet.
The power indicator illuminates red, and the projector enters standby mode.
2 Press on the remote control
or
on the projector.
The power indicator illuminates blue. After the lamp indicator illuminates, the projector is ready to start operation.
Note
The lamp indicator illuminates, indi­cating the status of the lamp.
Blue: The lamp is ready. Blue blinking: The lamp is
The lamp should be replaced.
Red:
If the projector is put into the standby mode and immediately turned on again, the lamp indicator may take some time to illuminate.
When controlling the projector using RS-232C commands from a com­puter, wait for at least 30 seconds after the power has been turned on, and then transmit the commands.
warming up.
", ',\, | buttons
ENTER button
STANDBY
button
ENTER
button
Power indicator
Lamp indicator
MENU button
INPUT button
STANDBY button
ON button
ON button
MENU button
", ', \, | buttons
INPUT buttons
-34
Page 36
3 Press , , , or
on the remote control or on the projector to select the IN­PUT mode.
After pressing once on the projector, use
to select the desired input mode.
Note
When no signal is received, “NO SIGNAL will be displayed. When a signal that the projector is not pre­set to receive is received, NOT REG. will be displayed.
The INPUT mode is not displayed when OSD display is set to Level A or Level B. (See page 68.)
About the INPUT modes
INPUT 1 INPUT 2 (
Compo-
/RGB*
nent
INPUT 3 (S-Video)
INPUT 4 (Video)
INPUT 5 (Digital PC RGB/ Digital PC Component/ Digital Video RGB/Digital Video Component/ Analog RGB/ Analog Component)
* Input the RGB signal of the DTV, not
the computer.
Used for projecting images from equipment that sends component signals or RGB
)
signals connected to the INPUT 1 or 2 terminals.
Used for projecting im­ages from equipment con­nected to the S-VIDEO in­put terminal.
Used for projecting im­ages from equipment connected to the VIDEO input terminal. Used for projecting im­ages from equipment connected to the DVI in­put terminal.
"On-screen Display (Example)
INPUT 1 mode
Using RGB*
Using Component
INPUT 2 mode
Using RGB*
Using Component
INPUT 3 mode
Using S-Video
INPUT 4 mode
Using Video
INPUT 5 mode
Using Analog RGB
The display varies accord­ing to the Signal Type with the INPUT 5. The diagram shown above is the ex­ample of having selected Analog RGB.
Basic Operation
-35
Page 37
Image Projection
Selecting the On-screen Display Language
The on-screen display language of the projector can be set to English, German, Spanish, Dutch, French, Italian, Swedish, Portuguese, Chinese, Korean or Japa­nese.
1 Press .
The menu will be displayed.
2 Press \ or | to select Lan-
guage”.
3 Press ' or " to select the de-
sired language, and then press
.
4 Press .
The desired language will be set as the on-screen display.
-36
Page 38
Turning the Power off
1 Press on the remote control
or
press confirmation message is dis-
played, to put the projector into the standby mode.
2
Unplug the power cord from the AC outlet after the cooling fan stops.
on the projector, then
or again while the
Note
If you accidentally pressed and do not want to put the projector into the standby mode, wait until the confirmation message disappears.
STANDBY
button
ENTER button
MENU button
", ', \, | buttons
Info
Do not unplug the power cord dur­ing projection or cooling fan opera­tion. This can cause damage due to the rise in internal temperature, as the cooling fan also stops.
When connected to equipment such as an amplifier, be sure to turn off the power to the equipment con­nected first and then to the projec­tor.
Basic Operation
-37
Page 39
Keystone Correction and Vertical Size Adjustment
Correcting Trapezoidal Distortion and Adjust­ing the Vertical Size of the Picture
This function allows for Keystone (On-screen Trapezoidal Distortion) Correction and the adjustment of the vertical size of the picture.
Note
When the image is projected either from top or from bottom toward the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal dis­tortion is called Keystone Correction.
The Keystone Correction can be adjusted up to angle of approximately ±20 degrees.
There are some input signal in which KEYSTONE does not work.
1 Press .
Each time is pressed, the settings toggles as shown on the right.
KEYSTONE button
ENTER button
UNDO button
Normal screen
Keystone Correc­tion screen
", ', \, | buttons
*
Vertical size adjustment screen
2 Press ", ', \ and | to adjust
the Keystone correction.
If you want to make more detailed cor­rections, press pattern, and then press
||
| to make the adjustments.
||
Note
Since the trapezoidal distortion of the im­age can be corrected up to an angle of approximately ±20 degrees, the actual screen can be diagonally set up to that angle as well.
Press to cancel Keystone Correction.
Straight lines or the edges of images may appear jagged while adjusting the image.
-38
to display the test
""
''
\\
",
',
\ and
""
''
\\
* V-SIZE is not dis-
played when the value of KEYSTONE is “0.
Compresses upper side.
Compresses lower side.
Test pattern
Page 40
3 When adjusting vertical size,
pressing the vertical size adjustment menu.
again displays
4 Press "and ' to adjust the
vertical size of the picture, and press
See below for details about the verti­cal size screen.
.
Vertical Size Adjustment
UNDO button
The image aspect ratio may change when the lens shift function is used in combination with the Keystone Correction function. In this case, adjust the aspect ratio using the vertical size adjustment.
Pressing ' increases the vertical length of the image.
Press to reset the image.
Pressing " decreases the vertical length of the image.
Press to reset the image.
Basic Operation
-39
Page 41
Menu Bar Items
This list shows the items that can be set in the projector.
INPUT 1 / 2 / 5 Mode
Main menu Sub menu
Picture Page 46
Gamma
Page 52
C.M.S. Page 54
Picture Position
Contrast
Bright
Color
Tint
Sharp
CLR Temp
Gamma Position
C.M.S. Position
Specials
Reset
Gamma Position Standard
R-Gamma
G-Gamma
B-Gamma
R-Gain
G-Gain
B-Gain
R-Offset
G-Offset
B-Offset
Reset
C.M.S. Position
Target
Lightness
Chroma
Hue
Reset (This Color)
Reset (All Colors)
View Settings
+30–30
+30–30
+30–30
+30–30
+30–30
110005000
+30–30
+30–30
+30–30
+30–30
+30–30
+30–30
+30–30
+30–30
+30–30
+30–30
+30–30
+30–30
Standard Natural Dynamic Custom 1 Custom 2 INPUT1/2/5 Position
Standard Black Detail Dynamic Gamma Custom 1 Custom 2 SVM Gamma
Standard Film Tone Custom 1 Custom 2
IP Mode [2D/3D/Film] White Emph [ON/OFF] DNR [OFF/Level 1-3] DFC [OFF/Level 1-3]
Black Detail Dynamic Gamma Custom 1 Custom 2 SVM Gamma
Standard Film Tone Custom 1 Custom 2
[R] Red [Y] Yellow [G] Green [C] Cyan [B] Blue [M] Magenta
Main menu Sub menu
Fine Sync Page 57
Options Page 66
Language Page 36
Clock
Phase
H-Pos
V-Pos
Reset
Save Setting
Select Setting
Special Modes
Signal Info
Auto Sync
Auto Sync Disp [ON/OFF]
Digi. Shift
Subtitle
Reset
LED [ON/OFF]
Lamp Timer
OSD Display
*
Signal Type
Background
Economy Mode
RS-232C
PRJ Mode
English Deutsch Español Nederlands Français Italiano Svenska Português
+150–150
+60–60
+150–150
+60–60
+30–30
+30–30
Resolution
1024 × 768 800 × 600
Resolution
1024 × 768
800 × 600
Resolution
1024 × 864
1152 × 864
1152 × 870
1152 × 882
Vert Freq
60 Hz 75 Hz
Vert Freq
60 Hz 75 Hz
1024 × 768
48.4 KHz 60 Hz
1 2
7
1 2
7
1 2 3 4
7
Resolution Hor Freq Vert Freq
OFF Normal High Speed
Normal Level A Level B
RGB Component
Blue None
Power Save [ON/OFF] RS-232C Port [ON/OFF] Auto Power Off [ON/OFF]
9600 bps 38400 bps 115200 bps
Front Ceiling + Front Rear Ceiling + Rear
Status Page 74
*In INPUT 5, the items in Signal Type are D. PC RGB, D. PC Comp., “D. Video RGB”, “D. Video Comp.”
A. RGB and A. Comp..
Note
The resolution, vertical frequency and horizontal frequency figures displayed above are for example purposes only.
Picture adjustment settings differ depending on the type of input signal.
-40
Page 42
INPUT 3 / 4 Mode
Main menu Sub menu
Picture Page 46
Gamma
Page 52
Picture Position
Contrast
Bright
Color
Tint
Sharp
CLR Temp
Gamma Position
C.M.S. Position
Specials
Reset
Gamma Position Standard
R-Gamma
G-Gamma
B-Gamma
R-Gain
G-Gain
B-Gain
R-Offset
G-Offset
B-Offset
Reset
Standard Natural Dynamic Custom 1 Custom 2 INPUT3/4 Position
+30–30
+30–30
+30–30
+30–30
+30–30
110005000
Standard Black Detail Dynamic Gamma Custom 1 Custom 2 SVM Gamma
Standard Film Tone Custom 1 Custom 2
IP Mode [2D/3D/Film] White Emph [ON/OFF] DNR [OFF/Level 1-3] DFC [OFF/Level 1-3]
+30–30
+30–30
+30–30
+30–30
+30–30
+30–30
+30–30
+30–30
+30–30
Black Detail Dynamic Gamma Custom 1 Custom 2 SVM Gamma
Main menu Sub menu
Options Page 66
Language Page 36
Status Page 74
Digi. Shift
Subtitle
Reset
LED [ON/OFF]
Lamp Timer
OSD Display
Video System
Background
Economy Mode
RS-232C
PRJ Mode
English Deutsch Español Nederlands Français Italiano Svenska Português
+30–30
+30–30
9600 bps 38400 bps 115200 bps
Normal Level A Level B
Auto PAL (50/60Hz) SECAM NTSC4.43 NTSC3.58 PAL-M PAL-N
Blue None
Power Save [ON/OFF] RS-232C Port [ON/OFF] Auto Power Off [ON/OFF]
Front Ceiling + Front Rear Ceiling + Rear
Basic Operation
C.M.S. Page 54
C.M.S. Position
Target
Lightness
Chroma
Hue
Reset (This Color)
Reset (All Colors)
View Settings
Standard Film Tone Custom 1 Custom 2
[R] Red [Y] Yellow
+30–30
[G] Green [C] Cyan
+30–30
[B] Blue [M] Magenta
+30–30
-41
Page 43
Using the Menu Screen
This projector has two sets of menu screens that allow you to adjust the image and various projector settings. You can operate the menus from the projector or remote control using the following proce­dure.
Menu screen for INPUT 1, INPUT 2 or INPUT 5 Mode
Menu Bar (Main Menu)
Menu Selections (Adjustments)
1 Press .
The menu screen is displayed.
Note
The “Picture menu screen for the selected input mode is displayed.
The on-screen display shown on the lower right is displayed when the IN­PUT 1, 2 or 5 mode is selected.
Menu screen for INPUT 3 or INPUT 4 Mode
""
''
\\
",
',
""
''
buttons
ENTER button
\,
\\
||
|
||
Menu Bar (Main Menu)
MENU button
-42
ENTER button
""
"Menu Screen
""
MENU button
""
''
\\
",
',
""
''
buttons
\,
\\
||
|
||
Page 44
2 Press
\\
\ or
\\
||
| to select the
||
menu you want to adjust.
Note
For details on the menus, see the tree charts on pages 40 and 41.
""
3 Press
''
" or
' to select the item
""
''
you want to adjust.
Note
To display a single adjustment item, press Only the menu bar and the selected adjustment item will be displayed. Then if you press " or ', the fol­lowing item (Bright after Con­trast) will be displayed.
after selecting the item.
||
|
||
Press screen.
4 Press
to return to the previous
\\
||
\ or
| to adjust the item
\\
||
selected.
The adjustment is stored.
5 Press .
The menu screen will disappear.
Basic Operation
-43
Page 45
Using the Menu Screen
Menu Selections (Settings)
1 Press .
The menu screen is displayed.
Note
The “Picture” menu screen for the selected input mode is displayed.
The on-screen displays shown on the lower right are displayed when INPUT 1, 2 or 5 mode is selected.
""
''
\\
',
''
\,
\\
|
||
||
",
""
buttons
ENTER button
MENU button
2 Press
\\
\ or
\\
||
| to select the
||
menu you want to adjust.
Note
For details on the menus, see the tree charts on pages 40 and 41.
""
3 Press
''
" or
' to select the
""
''
item you want to set.
Note
Press to return to the previous screen.
In some menus, select the icon us­ing
.
ENTER button
Menu screen
MENU button
""
''
\\
',
''
\,
\\
|
||
||
",
""
buttons
-44
Sub menu
Page 46
4 Press
The cursor shifts to the sub menu.
5 Press
||
|.
||
""
''
" or
' to select the set-
""
''
ting of the item displayed in the sub menu.
6 Press .
The item selected is set.
Sub menu
Basic Operation
Note
Some adjustment items will display a confirmation message. When setting an item, press \ or | to select “Ye s or OK and then press .
Use to select “ON or OFF for the item of Economy Mode”.
Use
to select setting for the item
of Specials in the Picture menu.
7 Press .
The menu will disappear.
-45
Page 47
Adjusting the Picture
You can adjust the projectors picture to your preferences with the following picture settings.
Selecting the Picture Position
This function allows you to select the picture position in accordance with brightness of the room or content of the software to be played. There are three preset positions and three po­sitions for custom settings. In all picture positions, items on the Picture menu can be adjusted and saved. When sav­ing, select a picture position before setting on the Picture menu.
Select Picture Position in the Pic­ture menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Selected Position Standard Natural
Sharp default setting A balanced color image
Description
is obtained.
Dynamic Custom 1
A vivid image is obtained. Allows you to store the
picture adjustment
Custom 2
settings to your prefer­ence.
INPUT1 Position
to
INPUT5 Position
Note
The picture position can be selected di­rectly by pressing changes in order each time
Picture adjustment settings can be stored for each input mode.
. The position
is pressed.
PICTURE POSITION button
-46
Page 48
Adjusting Image Prefer­ences
Adjust the Picture menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Selected Item Description
Contrast Bright Color Tint Sharp CLR Temp
For adjusting the contrast level For adjusting the brightness of an image For adjusting the color intensity of an image For adjusting the tones of an image For making sharper or softer the contour of an image For adjusting the color temperature of an image
Note
Picture adjustment settings differ depend­ing on the type of input signal.
Some items may not be adjustable de­pending on the combination of the INPUT mode and Signal Type setting.
Selecting the Gamma Position
This function allows you to select the desired gamma position.
\ button | button
For less contrast For less brightness For less color intensity Skin tones become purplish For less sharpness
Decreases color temperature for warmer, reddish, incandescent­like images.
For more contrast For more brightness For more color intensity Skin tones become greenish For more sharpness
Increases color temperature for cooler, bluish, fluorescent-like images.
Basic Operation
Select Gamma Position in the Pic­ture menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
Gamma can be adjusted in greater detail with Gamma on the menu screen. See page 52 for details.
-47
Page 49
Adjusting the Picture
Selecting the C.M.S. Position
This function allows you to select the desired color reproduction mode.
Select “C.M.S. Position” in the “Picture” menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
Color can be adjusted in greater detail with C.M.S. on the menu screen. See page 54 for details.
Special Settings
Select Specials in the Picture menu on the menu screen.
For operating the menu screen, see pages 42 to 45.
Selected Item
IP Mode
For selecting the pro-
Description
gressive display of a video signal (Page 49)
White Emph
For emphasizing the contrast (Page 50)
DNR
For reducing image noise (Page 50)
DFC
For emphasizing outlines in the image (Page 51)
-48
-48
Page 50
IP Mode
This function allows you to select the progres­sive display of a video signal. The progres­sive display projects a smoother video image.
Select IP Mode in the Specials menu on the Picture menu screen.
IP Mode is switched by pressing .
For operating the menu screen, see pages 42 to 45.
Selected Item
Description
Useful to display fast-moving
(2D Progressive)
images such as sports and action films. This mode optimizes the image in a displayed frame.
Useful to display relatively
(3D Progressive)
slow-moving images such as drama and documentary more clearly. This mode optimizes the image by estimating the movement of a number of preceding and succeeding frames.
Reproduces the image of film
(Film Mode)
source* clearly. Displays the optimized image of film transformed with three-two pull down (NTSC and PAL60Hz) or two-two pull down (PAL50Hz and SECAM) enhancement to progressive mode images.
*
The film source is a digital video recording with the original encoded as is at 24 frames/second. The pro­jector can convert this film source to progressive video at 60 frames/second with NTSC and PAL60Hz or at 50 frames/second with PAL50Hz and SECAM to play back a high-definition image.
Basic Operation
Note
When using progressive inputs, inputs are directly displayed so that 2D Progressive, 3D Progressive and Film Mode cannot be se­lected. These modes can be selected in in­terlace signals other than 1080
In NTSC or PAL60Hz, even if the 3D Progres­sive mode has been set, the three-two pull down enhancement will be enabled automati­cally when the film source has been entered.
In PAL50Hz or SECAM, the two-two pull down enhancement will be enabled only in the Film Mode, when the film source has been entered.
I.
-49
Page 51
Adjusting the Picture
Emphasizing the Contrast
This function emphasizes the bright portions of images to obtain a higher contrast image.
Select White Emph in the Specials menu on the Picture menu screen.
White Emph is switched ON andOFF by pressing .
For operating the menu screen, see pages 42 to 45.
Selected Item
(ON)
(OFF)
Emphasizes the bright portions of images.
Disables White Emph”.
Description
Reducing Image Noise (DNR)
Digital Noise Reduction (DNR) provides high quality images with minimal dot crawl and cross color noise.
Select DNR in the Specials menu on the Picture menu screen.
DNR is switched by pressing .
For operating the menu screen, see pages 42 to 45.
Selected Item
(OFF) (Level 1) (Level 2) (Level 3)
Disables DNR”.
Set a level so as to view a clearer picture.
Description
Note
Make sure to set DNR to OFF in the fol­lowing cases:
When the image is blurry.
When the contours and colors of mov-
ing images drag.
When TV broadcasts with weak signals are projected.
Info
This function is available with INPUT 1, 2
I, 480P, 576I and 576P signals) and
(480 INPUT 3, 4 (all signals).
-50
-50
Page 52
Emphasizing Outlines in the Image (DFC)
This function allows you to select features for outlines in the image.
Select “DFC” in the “Specials” on the “Picture” menu screen.
“DFC” is switched by pressing
For operating the menu screen, see pages 42 to 45.
.
Selected Item
(OFF)
(Level 1)
(Level 2)
(Level 3)
Disables “DFC”. Emphasize outlines a little
Emphasize outlines most
Description
Resetting All Adjust­ment Items
This function allows you to reset all adjust­ment items to the default setting.
Select “Reset” in the “Picture” menu on the menu screen and press
For operating the menu screen, see pages 42 to 45.
.
Basic Operation
-51
Page 53
Adjusting the Gamma
Use this function to select the gamma position and adjust the gamma curve for finer image adjustment.
Selecting the Gamma Position
Select Gamma Position in theGamma menu on the menu screen.
For operating the menu screen, see pages 42 to 45.
Selected Item Standard Black Detail
Dynamic Gamma
Custom 1–2
SVM Gamma
Note
The gamma position you set in this menu can be selected in the Gamma Position in the Picture menu.
Select “Custom 1 or Custom 2 to make the more detailed gamma setting.
For selecting “SVM Gamma, refer to the SharpVison Manager operation manual (supplied).
Sharp default setting Gives greater depth to
darker portions of image. A strong, clearly distinguish-
able image is obtained Allows you to adjust the
gamma curve for each of RGB.
Allows you to adjust gamma value using SharpVision Manager Software.
Description
Standard Black Detail Dynamic Gamma
SVM Gamma Custom 2 Custom 1
-52
Page 54
Adjusting the Gamma
Adjust the gamma curve to suit your prefer­ences. These gamma values can be adjusted only when the gamma position is set to Cus­tom 1 or Custom 2”.
Select the gamma item in the Gamma menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
To reset all adjustment items, select Re- set and press
.
Selected Item Description
R-Gamma (Red Gamma)
G-Gamma (Green Gamma)
B-Gamma (Blue Gamma)
R-Gain (Red Gain)
G-Gain (Green Gain)
B-Gain (Blue Gain)
R-Offset (Red Offset)
G-Offset (Green Offset)
B-Offset (Blue Offset)
For adjusting the display characteristic of red color
For adjusting the display characteristic of green color
For adjusting the display characteristic of blue color
For adjusting the contrast level of red color
For adjusting the contrast level of green color
For adjusting the contrast level of blue color
For adjusting the brightness level of red color
For adjusting the brightness level of green color
For adjusting the brightness level of blue color
\
button
For giving greater depth to brighter portion of image in red color.
For giving greater depth to brighter portion of image in green color.
For giving greater depth to brighter portion of image in blue color.
For less contrast in red color
For less contrast in green color
For less contrast in blue color
For less brightness in red color
For less brightness in green color
For less brightness in blue color
For giving greater depth to darker portion of image in red color.
For giving greater depth to darker portion of image in green color.
For giving greater depth to darker portion of image in blue color.
For more contrast in red color
For more contrast in green color
For more contrast in blue color
For more brightness in red color
For more brightness in green color
For more brightness in blue color
||
|
||
button
Basic Operation
-53
Page 55
Color Management System (C. M. S.)
This function allows you to individually adjust the display characteristics of six colors (R: Red, Y: Yellow, G: Green, C: Cyan, B: Blue, M: Magenta) .
Selecting the C.M.S. Position
Select “C.M.S. Position” in the “C.M.S.” menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Selected Item Standard Film Tone
Custom 1-2
Note
If “Standard is selected for C.M.S. Posi- tion, other items (e.g. Target) cannot be adjusted.
Sharp default setting A balanced color image is obtained.
Lightness”, “Chroma andHue can be adjusted for each
of the six colors.
Description
Selecting the Target Color
Select “Target” in the “C.M.S.” menu on the menu screen. For operating the menu screen, see pages 42 to 45.
-54
Red Cyan
Yellow Blue
Green Magenta
Page 56
Setting the Brightness of the Target Color
Select Lightness in the C.M.S. menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Setting the Chromatic Value of the Target Color
Select Chroma in the C.M.S. menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Basic Operation
Setting the Hue of the Target Color
Select Hue in the C.M.S. menu on the menu screen. For operating the menu screen, see pages 42 to 45.
-55
Page 57
Color Management System (C.M.S.)
Resetting User-Defined Color Settings
Select Reset (This Color) or Reset (All Colors) in the C.M.S. menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Selected Item
Reset (This Color)
Reset (All Colors)
Lightness, “Chroma and Hue of the color selected for Target are reset to the default setting.
Lightness”, “Chroma andHue of all colors are reset to
the default setting.
Description
Overview of All Color Settings
Select View Settings in the C.M.S. menu on the menu screen. For operating the menu screen, see pages 42 to 45.
-56
Page 58
Adjusting Computer Images
Use the Fine Sync function in case of irregularities such as vertical stripes or flickering in portions of the screen.
When Auto Sync is OFF
When Auto Sync is OFF, interference such as flickering or vertical stripes may oc­cur if displaying tilings or vertical stripes. Should this occur, adjust Clock, Phase”, H-Pos and V-Pos for obtaining an opti­mum image.
Select “Clock”, “Phase”, “H-Pos” or “V- Pos in the Fine Sync menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Basic Operation
Selected Item Description Clock Phase H-Pos
V-Pos
Note
Computer image adjustments can be made easily by pressing details.
To reset all adjustment items, select Re- set and press
.
Adjusts vertical noise. Adjusts horizontal noise (similar to tracking on your VCR). Centers the on-screen image by moving it to the left or right.
Centers the on-screen image by moving it up or down.
. See page 59 for
Saving Adjustment Settings
This projector allows you to store up to seven adjustment settings for use with various com­puters.
Select “Save Setting” in the “Fine Sync” menu on the menu screen. For operating the menu screen, see pages 42 to 45.
-57
Page 59
Adjusting Computer Images
Selecting Adjustment Settings
Adjustment settings stored in the projector can be easily accessed.
Select Select Setting in the Fine Sync menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
If a memory position has not been set, a resolution and frequency setting will not be displayed.
When selecting a stored adjustment set­ting with Select Setting, you can set the projector in the stored adjustments.
Special Mode Settings
Ordinarily, the type of input signal is detected and the correct resolution mode is automati­cally selected. However, for some signals, the optimal resolution mode in Special Modes on the Fine Sync menu screen may need to be selected to match the computer display mode.
Set the resolution by selecting Special Modes in the Fine Sync menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
Avoid displaying computer patterns which repeat every other line (horizontal stripes). (Flickering may occur, making the image hard to see.)
When a DVD player or Digital Video is con­nected, select 480P as the input signal.
See “Checking the Input Signal on the next page for information on the currently se­lected input signal.
-58
Page 60
Checking the Input Signal
This function allows you to check the current input signal information.
Select Signal Info in the Fine Sync menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Auto Sync Adjustment
Used to automatically adjust a computer image.
Select Auto Sync in the Fine Sync menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
When setting to Normal or
High Speed”:
Auto Sync adjustment will occur when the projector is turned on or when the inputs are switched, while connected to a com­puter.
Basic Operation
Manual adjustments should be per­formed:
When the optimum image cannot be achieved with Auto Sync adjustment. See page 57.
Auto Sync adjustment may take some time to complete, depending on the im­age of the computer connected to the projector.
When setting Auto Sync to OFF orHigh Speed, and if
Sync will be executed in High Speed mode. If the button is pressed again within one minute, Auto Sync will be ex­ecuted in Normal mode.
is pressed, Auto
Screen display during Auto Sync
AUTO SYNC button
-59
Page 61
Adjusting Computer Images
Auto Sync Display Function
Used to set the screen displayed during Auto Sync.
Select Auto Sync Disp in the Fine Sync menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Selected Item
Description
The image set as a back­ground image is projected.
The computer image being adjusted is displayed.
-60
Page 62
Easy to Use Functions
Easy to Use Functions
Page 63
Selecting the Picture Display Mode
This function allows you to modify or customize the picture display mode to enhance the input image. Depending on the input signal, you can choose SIDE BAR, “SMART STRETCH”, CINEMA ZOOM, STRETCH, “NORMAL or DOT BY DOT image.
RESIZE button
Switching the Picture Display Using Different Input Signals
Press .
Each time is pressed, the display changes as shown on pages 63 and 64.
Info
In the Dot by Dot Mode, images are dis­played in the original resolution, therefore they will not be enlarged.
To return to the standard image, press while “RESIZE is displayed on the screen.
RESIZE button
Screen display of the picture display mode
-62
-62
Page 64
VIDEO
SMART
STRETCH
For 4:3
aspect ratio
For 16:9
aspect ratio
480I
480P
576I
576P
NTSC
PAL
SECAM
SIDE BAR STRETCH
960 720 1280 720
960 720 1280 720480P
––720P
––
Select DOT BY DOT during 720P input when viewing 720P output from a computer.
720P switches between STRETCH and DOT BY DOT”. “STRETCH is fixed when 1080
Input Signal
SIDE BAR
SMART STRETCH
Output screen image
*
4:3 aspect ratio
480I 480P 540P
576I 576P NTSC
PAL
SECAM
Letterbox
*
*
Squeeze
CINEMA
ZOOM
1280 720
1280 720
*
*
*
STRETCH DOT BY DOTCINEMA ZOOM
DOT BY DOT
1280 720
1280 720
1280 720
1280 720
1280 720
I signal is entered.
1080I
540P 1080I
16:9 aspect ratio
720P
* Digi. Shift and Subtitle only move when in the SMART STRETCH and CINEMA ZOOM modes.
Easy to Use Functions
-63
Page 65
Selecting the Picture Display Mode
COMPUTER
For 4:3
aspect ratio
For without
4:3 aspect ratio
NORMAL DOT BY DOT
960 720 800 600 SVGA (800 600)
960 720 1024 720XGA (1024 768)
960 720 1280 720SXGA (1280 960)
900 720 1280 720SXGA (1280 1024)
VGA
SVGA
XGA
SXGA
Input Signal
4:3 aspect ratio (640 480)
4:3 aspect ratio (800 600)
4:3 aspect ratio (1024 768)
5:4 aspect ratio (1280 1024)
Output screen image
NORMAL
DOT BY DOT
-64
Page 66
Switchable High Brightness/High Contrast Mode
This function controls the quantity of the projected light and the contrast of the image. It can be operated using the IRIS button on the remote control.
Switching HIGH BRIGHTNESS MODE/ HIGH CONTRAST MODE
Press on the remote control to select the desired mode.The mode is switched in the order of HIGH BRIGHTNESS MODE, MEDIUM MODE and HIGH CONTRAST MODE”.
IRIS button
Selected Mode
HIGH BRIGHTNESS
MODE
MEDIUM
MODE
HIGH CONTRAST
MODE
Note
The projector is set to the “HIGH BRIGHT- NESS MODE when shipped from the fac­tory.
Description
High brightness is given priority over high contrast.
Intermediate mode between high contrast and high brightness
High contrast is given priority over high brightness.
Easy to Use Functions
-65
Page 67
Digital Shift Function
For easier viewing, this function shifts the entire image projected on the screen up or down when projecting 16:9 images from DVD players and DTV* decoders. * DTV is the umbrella term used to describe the new digital television system in the United States.
Adjusting the Digital Shift
Select Digi. Shift in the Options menu on the menu screen. For operating the menu screen, see pages 42 to 45.
button button
The image moves down. The image moves up.
Note
The Digital Shift Function works with the SMART STRETCH and CINEMA ZOOM screen. For details, see page 62.
Subtitle Setting
With this function, you can adjust the vertical size of the display to allow for subtitles.
Adjusting the Vertical Size of the Display
Select “Subtitle” in the “Options” menu on the menu screen. For operating the menu screen, see pages 42 to 45.
button button
The image is compressed by adjusting the vertical size of the display.
Note
When changing the screen with the Sub­title setting, not only the bottom of the screen rises, but also the upper part is changed to a certain point.
The subtitle setting can be adjusted more effectively with the Digital Shift function. The subtitle setting can be made only with
the SMART STRETCH and CINEMA ZOOM screen. For details, see page 62.
-66
The image is enlarged by adjusting the vertical size of the display.
Page 68
LED Off Function
LEDs (indicators) on the projector can be turned off when they are disturbing the projection.
Turning LED off
Select “LED” in the “Options” menu on the menu screen. For operating the menu screen, see pates 42 to 45.
Selected Item
(ON) (OFF)
Note
When Auto Power Off function is set to OFF, LED is set to ON automatically. Be sure to set Auto Power Off function to ON to use LED Off function. (See page
72.)
LEDs are turned on. LEDs are turned off while the
projector is in operation. (LEDs turn on while the pro­jector is in the standby mode, warming up or indicating problems.)
Description
Displaying the Lamp Usage Time
Easy to Use Functions
Confirming the Lamp Usage Time
This function allows you to check the lamp usage time.
Select Options menu to see the lamp usage time.
Note
It is recommended that the lamp be changed after approximately 1,900 cumu­lative hours of use.
Lamp Usage Time
-67
Page 69
Setting On-screen Display
This function allows you to turn on or off the on-screen messages. When setting Level A or Level B in OSD Display, the input mode display (e.g. INPUT 1) will not appear, even if the INPUT button is pressed.
Turning off the On-screen Display
Select OSD Display in the Options menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Selected Item
Normal Level A Level B
Description All On-screen Displays are displayed. Input and Auto Sync are not displayed. All On-screen Displays are not displayed.
(except for Menu, On-screen Displays displayed when the KEYSTONE button is pressed, and warning displays (Power off/Temp./Change The Lamp., etc.))
-68
Page 70
Selecting the Signal Type
This function allows you to select the input signal type RGB or Component for INPUT 1 and 2, or Digital PC RGB, Digital PC Component, Digital Video RGB, Digital Video Component, Analog RGB or Analog Component for INPUT 5.
For INPUT 1 and INPUT 2
Selecting the Signal Type
Select Signal Type in the Options menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
For INPUT 1 and INPUT 2
Set when RGB signals are
RGB
Component
received from video equip­ment.
Set when analog component signals are received from video equipment.
For INPUT 5
For INPUT 5
Set when digital PC RGB
D. PC RGB
D. PC Comp.
D. Video RGB
D. Video Comp.
A. RGB
A. Comp.
The input signal type can also be switched by pressing . This switching at this time is only able to be performed for switching
the of the above table.
signals are received from the computer.
Set when digital PC com­ponent signals are re­ceived from the com­puter.
Set when digital video RGB signals are re­ceived from video equip­ment.
Set when digital video component signals are received from video equipment.
Set when analog RGB signals are received.
Set when analog compo­nent signals are re­ceived.
Easy to Use Functions
RGB/COMP. button
-69
Page 71
Setting the Video System
The video input system mode is preset to Auto; however, a clear picture from the con­nected audio-visual equipment may not be received, depending on the video signal differ­ence. In that case, switch the video signal.
Setting the Video System
Select “Video System” in the “Options” menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
The video signal can only be set in IN­PUT 3 or INPUT 4 mode.
In “Auto, images are displayed in PAL even if PAL-N or PAL-M input signals are received.
PAL SECAM
NTSC4.43
NTSC3.58
When connected to PAL video equipment. When connected to SECAM video
equipment. When reproducing NTSC signals in
PAL video equipment. When connected to NTSC video equipment.
Setting a Background Image
This function allows you to select the image displayed when no signal is being sent to the projector.
Selecting a Background Image
Select Background in the Options menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Selected Item
Blue None
* If the input signal has interference, the screen
will be displayed with the interference.
Description Blue screen Black screen
*
-70
Page 72
Selecting the Economy Mode
These functions allow you to reduce the power consumption of the projector.
Setting the Power Save
Select Power Save in Economy Mode under the Options menu on the menu screen.
Power Save is switched ON andOFF by pressing .
For operating the menu screen, see pages 42 to 45.
Selected Item
(ON/Low
Power mode)
(OFF/
Standard mode)
Although noise is reduced when Power Save is set to ON, brightness decreases by 20%.
Power Save mode is factory preset to OFF”.
Description
Status
ON (
Low power mode
OFF
Standard mode
(
)
)
Brightness
80%
100%
Lamp power
consumption
220 W
270 W
RS-232C Off Function
This projector consumes power when using a computer connected to the RS-232C terminal. When not using these terminals, RS-232C Port can be set to OFF to reduce standby power consumption.
Select Mode under the Options menu menu screen.
RS-232C Port is switched ON and
For operating the menu screen, see pages 42 to 45.
Selected Item
RS-232C Port
in Economy
on the
OFF by pressing .
Description
(ON)
(OFF)
RS-232C connection is set to ON”. The RS-232C is operating at all times (to accept communications).
RS-232C connection is set to OFF. RS-232C does not operate when the power supply is in standby.
Note
Set “RS-232C Port to ON when using the
SharpVision Manager Software.
Easy to Use Functions
-71
Page 73
Selecting the Economy Mode
Automatic Power Off Function
Select Auto Power Off in Economy Mode under the Options menu screen.
Auto Power Off is switched ON andOFF by pressing .
For operating the menu screen, see pages 42 to 45.
Selected Item
(ON)
(OFF)
Note
When the Auto Power Off function is set to ON, 5 minutes before the projector enters the standby mode, the message Enter STANDBY mode in X min. will appear on the screen to indicate the remaining minutes.
When Auto Power Off function is set to OFF, LED is set to ON automatically. Be sure to set Auto Power Off function to ON to use LED Off function. (See page 67.)
When no input signal is detected for more than 15 minutes, the projector will automatically enter the standby mode.
The Auto Power Off function will be disabled.
menu on the
Description
Selecting the Transmission Speed (RS-232C)
This menu allows you to adjust the transmission speed of the RS-232C connection by select­ing the baud rate.
Selecting the Transmis­sion Speed (RS-232C)
Select RS-232C in the Options menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
Make sure that both the projector and com­puter are set for the same baud rate. Refer to the computers operation manual for instruc­tions for setting the computers baud rate.
-72
Page 74
Reversing/Inverting Projected Images
This projector is equipped with a reverse/invert image function that allows you to reverse or invert the projected image for various applications.
Setting the Projection Mode
Select PRJ Mode in the Options menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Selected Item
Front Ceiling + Front Rear Ceiling + Rear
Note
This function is used for the reversed im-
age and ceiling-mount setups. See page 32 for these setups.
Description Normal image Inverted image Reversed image Reversed and inverted image
Front Ceiling+Front Rear Ceiling+Rear
Easy to Use Functions
-73
Page 75
Displaying the Adjustment Settings
This function can be used to display all the adjusted settings as a list on the screen.
Overview of All Menu Settings
Select the Status menu on the menu screen and press . For operating the menu screen, see
pages 42 to 45.
-74
Page 76
Appendix
Appendix
Page 77
Maintenance
Cleaning the projector
Be sure to unplug the power cord before clean­ing the projector.
The cabinet as well as the operation panel is made of plastic. Avoid using benzene or thinner, as these can damage the finish on the cabinet.
Do not use volatile agents such as insecticides on the projector. Do not attach rubber or plastic items on the pro­jector for long time.
The effects of some of the agents in the plastic
may cause damage to the quality or finish of the projector.
Thinner
Wax
Wipe off dirt gently with a soft flannel cloth.
Neutral detergent
Cleaning the lens
Use a commercially available blower or lens cleaning paper (for glasses and camera lenses) for cleaning the lens. Do not use any liquid type cleaning agents, as they may wear off the coat­ing film on the surface of the lens.
As the surface of the lens can easily get dam­aged, be sure not to scrape or hit the lens.
Cleaning
Paper
Cleaning the exhaust and intake vents
Use a vacuum cleaner to clean dust from the exhaust vent and the intake vent.
Neutral detergent diluted with water
When the dirt is hard to remove, soak a cloth in a neutral detergent diluted with water, wring the cloth well and then wipe the projector. Strong cleaning detergents may discolor, warp or damage the coating on the projector. Make sure to test on a small, inconspicuous area on the projector before using.
-76
Page 78
Cleaning the Ventilative Holes
This projector is equipped with
ventilative holes to ensure the opti­mal operating condition of the projec­tor.
Periodically clean the ventilative hole
by vacuuming it off with a vacuum cleaner.
The ventilative holes should be
cleaned every 100 hours of use. Clean the ventilative holes more often when the projector is used in a dirty or smoky location.
Cleaning the Ventilative Holes
1 Press on the projector or
on the remote control to
put the projector into the standby mode.
Wait until the cooling fan stops.
Side and Rear view Bottom view
Ventilative holes
Ventilative holes
Ventilative holes
STANDBY button
Ventilative holes
STANDBY button
2 Disconnect the Power Cord.
3 Clean the dust off by putting
the cleaner hose on the intake ventilative holes.
Cleaner hose
Appendix
Cleaner hose
-77
Page 79
Maintenance Indicators
The warning lights on the projector indicate problems inside the projector.
If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate
red, and the projector will enter the standby mode. After the projector has entered the standby mode, follow the procedures given below.
Power indicator
Lamp indicator
Temperature warning indicator
About the temperature warning indicator
If the temperature inside the pro­jector increases, due to blockage of the air vents, or the setting lo­cation, “ lower left corner of the picture. If the temperature keeps on rising, the lamp will turn off and the tem­perature warning indicator will blink, the cooling fan will run for further 90 seconds, then the pro­jector will enter the standby mode. After “ appears, be sure to perform the following mea­sures.
” will blink in the
About the lamp indicator
When the lamp ex­ceeds 1,900 cumula­tive hours of use, “ ” will be displayed on the screen in yellow. When the cumulative hours of use reach 2,000, “ will automatically turn off and then the pro­jector will automatically enter the standby mode. At this time, the LAMP REPLACE­MENT indicator will illuminate in red.
If you try to turn on the projector a fourth
” will change to red, the lamp
time without replacing the lamp, the pro­jector will not turn on.
Maintenance indicator Condition Problem Possible Solution
Abnormal
Abnormal
Red on/ Standby
Red on/ Standby
Red blinks
Red blinks
The internal temperature is abnormally high.
The lamp does not illuminate.
Lamp replace­ment time.
The power indicator blinks in red when the projector is on.
Blocked air intake
Cooling fan break-
down
Internal circuit failure
Clogged air intake
Burnt-out lamp
Lamp circuit failure
The lamp usage
time has exceeded 1,900 hours.
The exhaust vent cover is open.
Relocate the projector to an area with proper ventilation.
Take the projector to your nearest Authorized SharpVision Service Center or Dealer for repair.
Clean the ventilative holes accord­ing to the procedure on page 77.
Carefully replace the lamp. (See page 81)
Take the projector to your nearest Authorized SharpVision Service Center or Dealer for repair.
Please exercise care when replacing the lamp.
Securely install the cover.
If the power indicator blinks even
when the exhaust vent cover is securely installed, contact your nearest Authorized SharpVision Service Center or Dealer for advice.
Temperature
warning
indicator
Lamp
indicator
Power
indicator
Normal
Off
Blue on*
Blue
blinks
when the
lamp is
active.
Blue on*/ Red on
* Blue is off when “LED” is set to “OFF”. (See page 67.)
-78
Page 80
Info
If the temperature warning indicator illuminates, and the projector enters the standby mode, follow the pos­sible solutions on the previous page and then wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 5 minutes.)
If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again.
If you want to clean the air vents during projector operation, be sure to put the projector into the standby mode. After the cooling fan has stopped, clean the vents.
Do not unplug the power cord after the projector has entered the standby mode and while the cooling fan is running. The cooling fan runs for about 90 seconds.
-79
Appendix
Page 81
Regarding the Lamp
Lamp
It is recommended that the lamp (sold separately) be replaced after approximately 1,900 cumulative
hours of use or when you notice a significant deterioration in the picture and color quality. The lamp usage time can be checked with Lamp Timer in the Options menu on the menu screen.
For lamp replacement, please consult your nearest Authorized SharpVision Service Center or Dealer.
The actual lamp service life may be less than 2,000 hours depending on the environment in which
the projector is used.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through an Authorized SharpVision Service Center or Dealer. For the name of the nearest Authorized SharpVision Service Center or Dealer, please call toll-free: 1-877-DTV-SHARP (1-877-388-7427).
Caution Concerning the Lamp
This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking.
When the lamp replacement indicator and on-screen display icon are illuminated or flash, it is rec-
ommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.
Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult with a doctor as soon as possible.
Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest Authorized SharpVision Service Center or Dealer to remove the damaged lamp and assure safe operation.
U.S.A. ONLY
Replacing the Lamp
Caution
Do not remove the lamp unit immediately after operation of the projector. The lamp will be hot and touching it can lead to burn or injury.
Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit.
If the new lamp does not light after replacement, take your projector to the nearest Authorized
SharpVision Service Center or Dealer for repair. Purchase a replacement lamp unit of type BQC­XVZ100005 from your nearest Authorized SharpVision Service Center or Dealer. Then carefully change the lamp by following the instructions described in this section. If you wish, you may have the lamp replaced at your nearest Authorized SharpVision Service Center or Dealer.
-80
Page 82
Removing and Install­ing the Lamp Unit
Info
Be sure to remove the lamp unit by the handle. Be sure not to touch the glass surface of the lamp unit or the inside of the projector.
To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below.
Do not loosen other screws except for the lamp unit cover and lamp unit. (Only the silver screws are loosened).
Please refer to the installation manual included with the lamp unit.
1 Press
on the projector or
STANDBY
on the remote control to
put the projector into the standby mode.
Wait until the cooling fan stops. Warning!
Do not remove the lamp unit from the
projector right after use. The lamp will be very hot and may cause burn or injury.
Lamp unit
BQC-XVZ100005
STANDBY
2 Disconnect the power cord.
Unplug the power cord from the AC
socket.
Leave the lamp until it has fully cooled
down (about 1 hour).
3 Remove the lamp unit cover.
Loosen the user service screws that
secure the lamp unit cover. Then open the cover in the direction of the arrow.
Appendix
User service screws
-81
Page 83
Regarding the Lamp
4 Remove the lamp unit.
Loosen the securing screws from the
lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow.
5 Insert the new lamp unit.
Press the lamp unit firmly into the lamp
unit compartment. Fasten the secur­ing screws.
6 Attach the lamp unit cover.
Close the lamp unit cover in the direc-
tion of the arrow (to the close mark) on the side of the projector. Then tighten the user service screws.
Info
If the lamp unit and lamp cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector.
2
1
User service screws
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
1 Connect the power cord.
Plug the power cord into the AC socket of the projector.
2 Reset the lamp timer.
While holding down , " and | on
the projector, press
“LAMP 0000H is displayed, indicat- ing that the lamp timer is reset.
Info
Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode.
on the projector.
-82
-82
Page 84
Connecting Pin Assignments
DVI-I (INPUT 5 / DIGITAL INPUT) port: 29 pin connector
DVI Digital INPUT
Pin No. Signal Pin No. Signal
1 T.M.D.S data 2– 16 Hot plug detection 2 T.M.D.S data 2+ 17 T.M.D.S data 0–
C3 C5
C4
C2
C1
16
24
8 7
23
•••••
•••••••••
•••
•••
18
17
~
•••••
~
2 1
•••••••••
9
~
3 T.M.D.S data 2 shield 18 T.M.D.S data 0+ 4 Not connected 19 T.M.D.S data 0 shield 5 Not connected 20 Not connected 6 DDC clock 21 Not connected 7 DDC data 22 T.M.D.S clock shield 8 Not connected 23 T.M.D.S clock+
9 T.M.D.S data 1– 24 T.M.D.S clock– 10 T.M.D.S data 1+ C1 Not connected 11 T.M.D.S data 1 shield C2 Not connected 12 Not connected C3 Not connected 13 Not connected C4 Not connected 14 +5V power C5 Ground 15 Ground
DVI Analog RGB Input
Pin No. Signal Pin No. Signal
1 Not connected 16 Hot plug detection 2 Not connected 17 Not connected 3 Not connected 18 Not connected 4 Not connected 19 Not connected 5 Not connected 20 Not connected 6 DDC clock 21 Not connected 7 DDC data 22 Not connected 8 Vertical sync 23 Not connected
9 Not connected 24 Not connected 10 Not connected C1 Analog input Red 11 Not connected C2 Analog input Green 12 Not connected C3 Analog input Blue 13 Not connected C4 Horizontal sync 14 +5V power C5 Ground 15 Ground
RS-232C Port: 9-pin D-sub male connector
Pin No. Signal Name I/O Reference
9
8 7 6
4 3 2 1
5
1 Not connected 2 RD Receive Data Input Connected to internal circuit 3 SD Send Data Output Connected to internal circuit 4 Reserved Connected to internal circuit 5 SG Signal Ground Connected to internal circuit 6 Reserved Connected to internal circuit 7 Reserved Connected to internal circuit 8 Reserved Connected to internal circuit 9 Not connected
DVI Analog Component Input
Pin No. Signal Pin No. Signal
1 Not connected 16 Not connected 2 Not connected 17 Not connected 3 Not connected 18 Not connected 4 Not connected 19 Not connected 5 Not connected 20 Not connected 6 Not connected 21 Not connected 7 Not connected 22 Not connected 8 Not connected 23 Not connected
9 Not connected 24 Not connected 10 Not connected C1 Analog input Pr/Cr 11 Not connected C2 Analog input Y 12 Not connected C3 Analog input Pb/Cb 13 Not connected C4 Not connected 14 Not connected C5 Ground 15 Ground
Appendix
-83
Page 85
(RS-232C) Specifications and Command Settings
PC control
A computer can be used to control the projector by connecting an RS-232C cable (null modem, cross type, commercially available) to the projector. (See page 25 for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table. Signal format: Conforms to RS-232C standard. Parity bit: None Baud rate*: 9,600 bps / 38,400bps / 115,200bps Stop bit: 1 bit Data length: 8 bits Flow control: None *Use the same settings for the projector and computer.
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After the projector processes the command from the computer, it sends a response code to the computer.
Command format
C1 C2 C3 C4 P1 P2 P3 P4
Return code (0DH)
Response code format
Command 4-digit Parameter 4-digit
Normal response
O K E R R
Return code (0DH)
Problem response (communication error or incorrect command)
Return code (
0DH)
Info
When more than one code is being sent, send each command only after the response code for the previous command from the projector is verified.
In the case of transmitting commands during standby, it takes a maximum of 30 seconds until the response code is received.
When the power is turned on during standby with the “POWER ON command, wait for at least 30 seconds after the power has been turned on, and then transmit the next command.
Note
When using the computer control function of the projector, the projector’s operating status cannot be read
by the computer. Therefore, confirm the status by transmitting the display commands for each adjustment menu and checking the status with the on-screen display. If the projector receives a command other than a menu display command, it will execute the command without displaying the on-screen display.
Commands
Example:
When BRIGHT of INPUT 1 image adjustment is set to 10.
RABR 1 0_
CONTROL CONTENTS
POWER ON STANDBY KEYSTONE (–127 – +127) V-SIZE (–10 – +10) INPUT 1 INPUT 2 INPUT 3 INPUT 4 INPUT 5 INPUT CHECK AUTO SYNC START INPUT 1 RESIZE : SIDE BAR/DOT BY DOT/NORMAL
BUTTONS & REMOTE CONTROL KEY
INPUT 1 RESIZE : SMART STRETCH INPUT 1 RESIZE : CINEMA ZOOM INPUT 1 RESIZE : STRETCH
COMMAND
P P K V I I I I I I
A R R R R
O O E S R R V V R C D A A A A
W W
Y
I G G
E
E G H
J S S S S
PARAMETER
R
_
R
_
S
*
Z
_
B
_
B
_
D
_
D
_
B
_
K
_
S
_
R
_
R
_
R
_
R
_
_ _ * * _ _ _ _ _ _ _ _ _ _ _
OK OR ERR
1
OK OR ERR
0
OK OR ERR
*
OK OR ERR
*
OK OR ERR
1
OK OR ERR
2
OK OR ERR
2
OK OR ERR
1
OK OR ERR
3
OK OR ERR
0
OK OR ERR
1
OK OR ERR
3
OK OR ERR
4
OK OR ERR
1
OK OR ERR
2
RETURN
_ _ * _ _ _ _ _ _ _ _ _ _ _ _
→ ←
ProjectorComputer
OK
CONTROL CONTENTS
INPUT 2 RESIZE : SIDE BAR/DOT BY DOT/NORMAL INPUT 2 RESIZE : SMART STRETCH INPUT 2 RESIZE : CINEMA ZOOM INPUT 2 RESIZE : STRETCH INPUT 3 RESIZE : SIDE BAR INPUT 3 RESIZE : SMART STRETCH INPUT 3 RESIZE : CINEMA ZOOM INPUT 3 RESIZE : STRETCH INPUT 4 RESIZE : SIDE BAR INPUT 4 RESIZE : SMART STRETCH INPUT 4 RESIZE : CINEMA ZOOM INPUT 4 RESIZE : STRETCH INPUT 5 RESIZE : SIDE BAR/DOT BY DOT/NORMAL INPUT 5 RESIZE : SMART STRETCH
BUTTONS & REMOTE CONTROL KEY
INPUT 5 RESIZE : CINEMA ZOOM INPUT 5 RESIZE : STRETCH IRIS : High Brightness IRIS : Medium IRIS : High Contrast
COMMAND
R
B
S
R
B
S
R
B
S
R
B
S
R
B
S
R
B
S
R
B
S
R
B
S
R
A
S
R
A
S
R
A
S
R
A
S
R
C
S
R
C
S
R
C
S
R
C
S
I
R
I
I
R
I
I
R
I
PARAMETER
R
_
_
R
_
_
R
_
_
R
_
_
V
_
_
V
_
_
V
_
_
V
_
_
V
_
_
V
_
_
V
_
_
V
_
_
R
_
_
R
_
_
R
_
_
R
_
_
S
_
_
S
_
_
S
_
_
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
OK OR ERR
3
OK OR ERR
4
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
4
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
4
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
4
OK OR ERR
1
OK OR ERR
2
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
RETURN
-84
Page 86
CONTROL CONTENTS
INPUT 1 PICTUR PSN : INPUT 1 POSITION INPUT 1 PICTUR PSN : STANDARD INPUT 1 PICTUR PSN : NATURAL INPUT 1 PICTUR PSN : DYNAMIC INPUT 1 PICTUR PSN : CUSTOM 1 INPUT 1 PICTUR PSN : CUSTOM 2 INPUT 1 CONTRAST (–30 – +30) INPUT 1 BRIGHT (–30 – +30) INPUT 1 COLOR (–30 – +30) INPUT 1 TINT (–30 – +30) INPUT 1 SHARP (–30 – +30) INPUT 1 CLR TEMP (50 – 110) INPUT 1 DISPLAY INPUT 1 ADJUSTMENT RESET INPUT 2 PICTUR PSN : INPUT 2 POSITION INPUT 2 PICTUR PSN : STANDARD INPUT 2 PICTUR PSN : NATURAL INPUT 2 PICTUR PSN : DYNAMIC INPUT 2 PICTUR PSN : CUSTOM 1 INPUT 2 PICTUR PSN : CUSTOM 2 INPUT 2 CONTRAST (–30 – +30) INPUT 2 BRIGHT (–30 – +30) INPUT 2 COLOR (–30 – +30) INPUT 2 TINT (–30 – +30) INPUT 2 SHARP (–30 – +30) INPUT 2 CLR TEMP (50 – 110) INPUT 2 DISPLAY INPUT 2 ADJUSTMENT RESET INPUT 5 PICTUR PSN : INPUT 5 POSITION INPUT 5 PICTUR PSN : STANDARD INPUT 5 PICTUR PSN : NATURAL INPUT 5 PICTUR PSN : DYNAMIC INPUT 5 PICTUR PSN : CUSTOM 1 INPUT 5 PICTUR PSN : CUSTOM 2 INPUT 5 CONTRAST (–30 – +30) INPUT 5 BRIGHT (–30 – +30) INPUT 5 COLOR (–30 – +30) INPUT 5 TINT (–30 – +30) INPUT 5 SHARP (–30 – +30) INPUT 5 CLR TEMP (50 – 110) INPUT 5 DISPLAY
PICTURE
INPUT 5 ADJUSTMENT RESET INPUT 1 IP MODE : 2D PROGRESSIVE INPUT 1 IP MODE : 3D PROGRESSIVE INPUT 1 IP MODE : Film MODE INPUT 1 WHITE EMPH : OFF INPUT 1 WHITE EMPH : ON INPUT 1 DNR : OFF INPUT 1 DNR : LEVEL 1 INPUT 1 DNR : LEVEL 2 INPUT 1 DNR : LEVEL 3 INPUT 1 DFC : OFF INPUT 1 DFC : LEVEL 1 INPUT 1 DFC : LEVEL2 INPUT 1 DFC : LEVEL 3 INPUT 2 IP MODE : 2D PROGRESSIVE INPUT 2 IP MODE : 3D PROGRESSIVE INPUT 2 IP MODE : Film MODE INPUT 2 WHITE EMPH : OFF INPUT 2 WHITE EMPH : ON INPUT 2 DNR : OFF INPUT 2 DNR : LEVEL 1 INPUT 2 DNR : LEVEL 2 INPUT 2 DNR : LEVEL 3 INPUT 2 DFC : OFF INPUT 2 DFC : LEVEL 1 INPUT 2 DFC : LEVEL 2 INPUT 2 DFC : LEVEL 3 INPUT 5 IP MODE : 2D PROGRESSIVE INPUT 5 IP MODE : 3D PROGRESSIVE INPUT 5 IP MODE : Film MODE INPUT 5 WHITE EMPH : OFF INPUT 5 WHITE EMPH : ON INPUT 5 DNR : OFF INPUT 5 DNR : LEVEL 1 INPUT 5 DNR : LEVEL 2 INPUT 5 DNR : LEVEL 3 INPUT 5 DFC : OFF INPUT 5 DFC : LEVEL 1 INPUT 5 DFC : LEVEL 2 INPUT 5 DFC : LEVEL 3
COMMAND
R
A
P
R
A
P
R
A
P
R
A
P
R
A
P
R
A
P
R
A
P
R
A
B
R
A
C
R
A
T
R
A
S
R
A
C
R
A
R
R
A
R
R
B
P
R
B
P
R
B
P
R
B
P
R
B
P
R
B
P
R
B
P
R
B
B
R
B
C
R
B
T
R
B
S
R
B
C
R
B
R
R
B
R
R
C
P
R
C
P
R
C
P
R
C
P
R
C
P
R
C
P
R
C
P
R
C
B
R
C
C
R
C
T
R
C
S
R
C
C
R
C
R
R
C
R
R
A
I
R
A
I
R
A
I
R
A
W
R
A
W
R
A
N
R
A
N
R
A
N
R
A
N
R
A
D
R
A
D
R
A
D
R
A
D
R
B
I
R
B
I
R
B
I
R
B
W
R
B
W
R
B
N
R
B
N
R
B
N
R
B
N
R
B
D
R
B
D
R
B
D
R
B
D
R
C
I
R
C
I
R
C
I
R
C
W
R
C
W
R
C
N
R
C
N
R
C
N
R
C
N
R
C
D
R
C
D
R
C
D
R
C
D
PARAMETER
S
_
S
_
S
_
S
_
S
_
S
_
I
_
R
_
O
_
I
_
H
_
T
_
E
_
E
_
S
_
S
_
S
_
S
_
S
_
S
_
I
_
R
_
O
_
I
_
H
_
T
_
E
_
E
_
S
_
S
_
S
_
S
_
S
_
S
_
I
_
R
_
O
_
I
_
H
_
T
_
E
_
E
_
P
_
P
_
P
_
E
_
E
_
R
_
R
_
R
_
R
_
F
_
F
_
F
_
F
_
P
_
P
_
P
_
E
_
E
_
R
_
R
_
R
_
R
_
F
_
F
_
F
_
F
_
P
_
P
_
P
_
E
_
E
_
R
_
R
_
R
_
R
_
F
_
F
_
F
_
F
_
_ _ _ _ _ _ * * * * * * _ _ _ _ _ _ _ _ * * * * * * _ _ _ _ _ _ _ _ * * * * * * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
RETURN CONTROL CONTENTS
_
OK OR ERR _ _ _ _ _ * * * * * * _ _ _ _ _ _ _ _ * * * * * * _ _ _ _ _ _ _ _ * * * * * * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
4
OK OR ERR
5
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
0
OK OR ERR
1
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
4
OK OR ERR
5
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
0
OK OR ERR
1
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
4
OK OR ERR
5
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
0
OK OR ERR
1
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
0
OK OR ERR
1
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
0
OK OR ERR
1
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
0
OK OR ERR
1
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
INPUT 3 PICTUR PSN : INPUT 3 POSITION INPUT 3 PICTUR PSN : STANDARD INPUT 3 PICTUR PSN : NATURAL INPUT 3 PICTUR PSN : DYNAMIC INPUT 3 PICTUR PSN : CUSTOM 1 INPUT 3 PICTUR PSN : CUSTOM 2 INPUT 3 CONTRAST (–30 – +30) INPUT 3 BRIGHT (–30 – +30) INPUT 3 COLOR (–30 – +30) INPUT 3 TINT (–30 – +30) INPUT 3 SHARP (–30 – +30) INPUT 3 CLR TEMP (50 – 110) INPUT 3 DISPLAY INPUT 3 ADJUSTMENT RESET INPUT 4 PICTUR PSN : INPUT 4 POSITION INPUT 4 PICTUR PSN : STANDARD INPUT 4 PICTUR PSN : NATURAL INPUT 4 PICTUR PSN : DYNAMIC INPUT 4 PICTUR PSN : CUSTOM 1 INPUT 4 PICTUR PSN : CUSTOM 2 INPUT 4 CONTRAST (–30 – +30) INPUT 4 BRIGHT (–30 – +30) INPUT 4 COLOR (–30 – +30) INPUT 4 TINT (–30 – +30) INPUT 4 SHARP (–30 – +30) INPUT 4 CLR TEMP (50 – 110) INPUT 4 DISPLAY INPUT 4 ADJUSTMENT RESET INPUT 3 IP MODE : 2D PROGRESSIVE INPUT 3 IP MODE : 3D PROGRESSIVE
PICTURE
INPUT 3 IP MODE : Film MODE INPUT 3 WHITE EMPH : OFF INPUT 3 WHITE EMPH : ON INPUT 3 DNR : OFF INPUT 3 DNR : LEVEL 1 INPUT 3 DNR : LEVEL 2 INPUT 3 DNR : LEVEL 3 INPUT 3 DFC : OFF INPUT 3 DFC : LEVEL 1 INPUT 3 DFC : LEVEL 2 INPUT 3 DFC : LEVEL 3 INPUT 4 IP MODE : 2D PROGRESSIVE INPUT 4 IP MODE : 3D PROGRESSIVE INPUT 4 IP MODE : Film MODE INPUT 4 WHITE EMPH : OFF INPUT 4 WHITE EMPH : ON INPUT 4 DNR : OFF INPUT 4 DNR : LEVEL 1 INPUT 4 DNR : LEVEL 2 INPUT 4 DNR : LEVEL 3 INPUT 4 DFC : OFF INPUT 4 DFC : LEVEL 1 INPUT 4 DFC : LEVEL 2 INPUT 4 DFC : LEVEL 3 INPUT 1 GAMMA POSITION : STANDARD INPUT 1 GAMMA POSITION : BLACK DETAIL INPUT 1 GAMMA POSITION : DYNAMIC GAMMA INPUT 1 GAMMA POSITION : CUSTOM 1 INPUT 1 GAMMA POSITION : CUSTOM 2 INPUT 1 GAMMA POSITION : SVM GAMMA INPUT 2 GAMMA POSITION : STANDARD INPUT 2 GAMMA POSITION : BLACK DETAIL INPUT 2 GAMMA POSITION : DYNAMIC GAMMA INPUT 2 GAMMA POSITION : CUSTOM 1
GAMMA
INPUT 2 GAMMA POSITION : CUSTOM 2 INPUT 2 GAMMA POSITION : SVM GAMMA INPUT 3 GAMMA POSITION : STANDARD INPUT 3 GAMMA POSITION : BLACK DETAIL INPUT 3 GAMMA POSITION : DYNAMIC GAMMA INPUT 3 GAMMA POSITION : CUSTOM 1 INPUT 3 GAMMA POSITION : CUSTOM 2 INPUT 3 GAMMA POSITION : SVM GAMMA
COMMAND
V
B
P
V
B
P
V
B
P
V
B
P
V
B
P
V
B
P
V
B
P
V
B
B
V
B
C
V
B
T
V
B
S
V
B
C
V
B
R
V
B
R
V
A
P
V
A
P
V
A
P
V
A
P
V
A
P
V
A
P
V
A
P
V
A
B
V
A
C
V
A
T
V
A
S
V
A
C
V
A
R
V
A
R
V
B
I
V
B
I
V
B
I
V
B
W
V
B
W
V
B
N
V
B
N
V
B
N
V
B
N
V
B
D
V
B
D
V
B
D
V
B
D
V
A
I
V
A
I
V
A
I
V
A
W
V
A
W
V
A
N
V
A
N
V
A
N
V
A
N
V
A
D
V
A
D
V
A
D
V
A
D
G
M
R
G
M
R
G
M
R
G
M
R
G
M
R
G
M
R
G
M
R
G
M
R
G
M
R
G
M
R
G
M
R
G
M
R
G
M
V
G
M
V
G
M
V
G
M
V
G
M
V
G
M
V
PARAMETER
S
_
_
S
_
_
S
_
_
S
_
_
S
_
_
S
_
_
I
_
*
R
_
*
O
_
*
I
_
*
H
_
*
T
_
*
E
_
_
E
_
_
S
_
_
S
_
_
S
_
_
S
_
_
S
_
_
S
_
_
I
*
*
R
*
*
O
*
*
I
*
*
H
_
*
T
_
*
E
_
_
E
_
_
P
_
_
P
_
_
P
_
_
E
_
_
E
_
_
R
_
_
R
_
_
R
_
_
R
_
_
F
_
_
F
_
_
F
_
_
F
_
_
P
_
_
P
_
_
P
_
_
E
_
_
E
_
_
R
_
_
R
_
_
R
_
_
R
_
_
F
_
_
F
_
_
F
_
_
F
_
_
A
_
_
A
_
_
A
_
_
A
_
_
A
_
_
A
_
_
B
_
_
B
_
_
B
_
_
B
_
_
B
_
_
B
_
_
B
_
_
B
_
_
B
_
_
B
_
_
B
_
_
B
_
_
_ _ _ _ _ _ * * * * * * _ _ _ _ _ _ _ _ * * * * * * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
4
OK OR ERR
5
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
0
OK OR ERR
1
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
4
OK OR ERR
5
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
0
OK OR ERR
1
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
0
OK OR ERR
1
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
0
OK OR ERR
1
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
4
OK OR ERR
5
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
4
OK OR ERR
5
OK OR ERR
0
OK OzR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
4
OK OR ERR
5
RETURN
Appendix
-85
Page 87
(RS-232C) Specifications and Command Settings
CONTROL CONTENTS
INPUT 4 GAMMA POSITION : STANDARD INPUT 4 GAMMA POSITION : BLACK DETAIL INPUT 4 GAMMA POSITION : DYNAMIC GAMMA INPUT 4 GAMMA POSITION : CUSTOM 1 INPUT 4 GAMMA POSITION : CUSTOM 2 INPUT 4 GAMMA POSITION : SVM GAMMA INPUT 5 GAMMA POSITION : STANDARD INPUT 5 GAMMA POSITION : BLACK DETAIL INPUT 5 GAMMA POSITION : DYNAMIC GAMMA INPUT 5 GAMMA POSITION : CUSTOM 1 INPUT 5 GAMMA POSITION : CUSTOM 2 INPUT 5 GAMMA POSITION : SVM GAMMA R-GAMMA (–30 – +30)
GAMMA
G-GAMMA (–30 – +30) B-GAMMA (–30 – +30) R-GAIN (–30 – +30) G-GAIN (–30 – +30) B-GAIN (–30 – +30) R-OFFSET (–30 – +30) G-OFFSET (–30 – +30) B-OFFSET (–30 – +30) GAMMA RESET INPUT 1 CMS : STANDARD INPUT 1 CMS : FILM TONE INPUT 1 CMS : CUSTOM 1 INPUT 1 CMS : CUSTOM 2 INPUT 2 CMS : STANDARD INPUT 2 CMS : FILM TONE INPUT 2 CMS : CUSTOM 1 INPUT 2 CMS : CUSTOM 2 INPUT 3 CMS : STANDARD INPUT 3 CMS : FILM TONE INPUT 3 CMS : CUSTOM 1 INPUT 3 CMS : CUSTOM 2 INPUT 4 CMS : STANDARD INPUT 4 CMS : FILM TONE INPUT 4 CMS : CUSTOM 1 INPUT 4 CMS : CUSTOM 2 INPUT 5 CMS : STANDARD INPUT 5 CMS : FILM TONE
C.M.S.
INPUT 5 CMS : CUSTOM 1 INPUT 5 CMS : CUSTOM 2 TARGET : RED TARGET : YELLOW TARGET : GREEN TARGET : CYAN TARGET : BLUE TARGET : MAGENTA LIGHTNESS (–30 – +30) CHROMA (–30 – +30) HUE (–30 – +30) RESET (THIS COLOR) RESET (ALL COLORS)
1
CLOCK (–150 – +150) PHASE (–60 – +60) H-POSITION (–150 – +150)
FINE SYNC*
V-POSITION (–60 – +60)
COMMAND
G
M
V
G
M
V
G
M
V
G
M
V
G
M
V
G
M
V
G
M
R
G
M
R
G
M
R
G
M
R
G
M
R
G
M
R
G
M
E
G
M
E
G
M
E
G
M
G
G
M
G
G
M
G
G
M
O
G
M
O
G
M
O
G
M
R
C
S
R
C
S
R
C
S
R
C
S
R
C
S
R
C
S
R
C
S
R
C
S
R
C
S
V
C
S
V
C
S
V
C
S
V
C
S
V
C
S
V
C
S
V
C
S
V
C
S
R
C
S
R
C
S
R
C
S
R
C
M
T
C
M
T
C
M
T
C
M
T
C
M
T
C
M
T
C
M
S
C
M
S
C
M
S
C
M
R
C
M
R
I
N
C
I
N
P
I
A
H
I
A
V
PARAMETER
A
_
A
_
A
_
A
_
A
_
A
_
C
_
C
_
C
_
C
_
C
_
C
_
R
_
G
_
B
_
R
_
G
_
B
_
R
_
G
_
B
_
E
_
A
_
A
_
A
_
A
_
B
_
B
_
B
_
B
_
B
_
B
_
B
_
B
_
A
_
A
_
A
_
A
_
C
_
C
_
C
_
C
_
G
_
G
_
G
_
G
_
G
_
G
_
L
_
C
_
H
_
E
_
E
_
L
*
H
_
P
*
P
_
_ _ _ _ _ _ _ _ _ _ _ _ * * * * * * * * * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ * * * _ _ * * * *
RETURN CONTROL CONTENTS
_
OK OR ERR _ _ _ _ _ _ _ _ _ _ _ * * * * * * * * * _ _ 2 1 1 _ 2 1 1 _ 2 1 1 _ 2 1 1 _ 2 1 1 _ _ _ _ _ _ * * * _ _ * * * *
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
4
OK OR ERR
5
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
4
OK OR ERR
5
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
1
OK OR ERR
0
OK OR ERR
1
OK OR ERR
1
OK OR ERR
2
OK OR ERR
0
OK OR ERR
1
OK OR ERR
1
OK OR ERR
2
OK OR ERR
0
OK OR ERR
1
OK OR ERR
1
OK OR ERR
2
OK OR ERR
0
OK OR ERR
1
OK OR ERR
1
OK OR ERR
2
OK OR ERR
0
OK OR ERR
1
OK OR ERR
1
OK OR ERR
2
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
4
OK OR ERR
5
OK OR ERR
6
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
1
OK OR ERR
2
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
RGB INPUT DISPLAY RGB ADJUSTMENT RESET SAVE SETTING (1 – 7) SELECT SETTING (1 – 7)
1
RGB HORIZONTAL FREQUENCY CHECK RGB VERTICAL FREQUENCY CHECK AUTO SYNC : ON (NOTMAL)
FINE SYNC*
AUTO SYNC : ON (HIGH SPEED) AUTO SYNC : OFF AUTO SYNC DISPLAY ON AUTO SYNC DISPLAY OFF DIGITAL SHIFT (–30 – +30) SUBTITLE (–30 – +30) POWER SAVE MODE : ON POWER SAVE MODE : OFF LED : ON LED : OFF OSD DISPLAY : NORMAL OSD DISPLAY : LEVEL A OSD DISPLAY : LEBEL B INPUT 1 SIGNAL TYPE : RGB INPUT 1 SIGNAL TYPE : COMPONENT INPUT 2 SIGNAL TYPE : RGB INPUT 2 SIGNAL TYPE : COMPONENT VIDEO SYSTEM SELECTION : AUTO VIDEO SYSTEM SELECTION : PAL VIDEO SYSTEM SELECTION : SECAM VIDEO SYSTEM SELECTION : NTSC4.43 VIDEO SYSTEM SELECTION : NTSC3.58
Options
VIDEO SYSTEM SELECTION : PAL-M VIDEO SYSTEM SELECTION : PAL-N INPUT 5 SIGNAL TYPE : ANALOG RGB INPUT 5 SIGNAL TYPE : ANALOG COMPONENT INPUT 5 SIGNAL TYPE : DIGITAL COMPUTER (RGB) INPUT 5 SIGNAL TYPE : DIGITAL COMPUTER (COMPONENT) INPUT 5 SIGNAL TYPE : DIGITAL VIDEO (RGB) INPUT 5 SIGNAL TYPE : DIGITAL VIDEO (COMPONENT) BACKGROUND SELECTION : BLUE BACKGROUND SELECTION : NONE AUTO POWER OFF : NO USE AUTO POWER OFF : USE LAMP USAGE TIME PROJECTION MODE : FRONT PROJECTION MODE : CEILING + FRONT PROJECTION MODE : REAR PROJECTION MODE : CEILING + REAR LANGUAGE SELECTION : ENGLISH LANGUAGE SELECTION : DEUTSCH LANGUAGE SELECTION : ESPAÑOL LANGUAGE SELECTION : NEDERLANDS LANGUAGE SELECTION : FRANÇAIS LANGUAGE SELECTION : ITALIANO LANGUAGE SELECTION : SVENSKA
LANGUAGE
LANGUAGE SELECTION : LANGUAGE SELECTION : PORTUGUÊS LANGUAGE SELECTION : LANGUAGE SELECTION :
COMMAND
I
A
R
I
A
R
M
E
M
M
E
M
T
F
R
T
F
R
A
A
D
A
A
D
A
A
D
I
M
A
I
M
A
S
T
S
S
T
S
T
H
M
T
H
M
L
E
D
L
E
D
I
M
D
I
M
D
I
M
D
I
A
S
I
A
S
I
B
S
I
B
S
M
E
S
M
E
S
M
E
S
M
E
S
M
E
S
M
E
S
M
E
S
I
C
S
I
C
S
I
C
S
I
C
S
I
C
S
I
C
S
I
M
B
I
M
B
A
P
O
A
P
O
T
L
T
I
M
P
I
M
P
I
M
P
I
M
P
M
E
L
M
E
L
M
E
L
M
E
L
M
E
L
M
E
L
M
E
L
M
E
L
M
E
L
M
E
L
M
E
L
PARAMETER
E
_
_
E
_
_
S
_
_
L
_
_
Q
_
_
Q
_
_
J
_
_
J
_
_
J
_
_
S
_
_
S
_
_
H
_
*
Z
_
*
D
_
_
D
_
_
S
_
_
S
_
_
I
_
_
I
_
_
I
_
_
I
_
_
I
_
_
I
_
_
I
_
_
Y
_
_
Y
_
_
Y
_
_
Y
_
_
Y
_
_
Y
_
_
Y
_
_
I
_
_
I
_
_
I
_
_
I
_
_
I
_
_
I
_
_
G
_
_
G
_
_
W
_
_
W
_
_
T
_
_
J
_
_
J
_
_
J
_
_
J
_
_
A
_
_
A
_
_
A
_
_
A
_
_
A
_
_
A
_
_
A
_
_
A
_
_
A
_
_
A
_
_
A
_
_
_
OK OR ERR
0
_
OK OR ERR
1
_
OK OR ERR
*
_
OK OR ERR
*
_
kHz (***. *OR_)
1
_
Hz (***. *OR_)
2
_
OK OR ERR
1
_
OK OR ERR
2
_
OK OR ERR
0
_
OK OR ERR
1
_
OK OR ERR
0
*
OK OR ERR
*
*
OK OR ERR
*
_
OK OR ERR
1
_
OK OR ERR
0
_
OK OR ERR
1
_
OK OR ERR
0
_
OK OR ERR
1
_
OK OR ERR
2
_
OK OR ERR
0
_
OK OR ERR
1
_
OK OR ERR
2
_
OK OR ERR
1
_
OK OR ERR
2
_
OK OR ERR
1
_
OK OR ERR
2
_
OK OR ERR
3
_
OK OR ERR
4
_
OK OR ERR
5
_
OK OR ERR
6
_
OK OR ERR
7
_
OK OR ERR
1
_
OK OR ERR
2
_
OK OR ERR
3
_
OK OR ERR
4
_
OK OR ERR
5
_
OK OR ERR
6
_
OK OR ERR
1
_
OK OR ERR
2
_
OK OR ERR
0
_
OK OR ERR
1
_
0–9999 (INTEGER)
1
_
OK OR ERR
0
_
OK OR ERR
1
_
OK OR ERR
2
_
OK OR ERR
3
_
OK OR ERR
1
_
OK OR ERR
2
_
OK OR ERR
3
_
OK OR ERR
4
_
OK OR ERR
5
_
OK OR ERR
6
_
OK OR ERR
7
_
OK OR ERR
8
_
OK OR ERR
9
1
OK OR ERR
0
1
OK OR ERR
1
RETURN
Note
If an underbar (_) appears in the parameter column, enter a space. If an asterisk (*) appears, enter a value in the range indicated in brackets under CONTROL CONTENTS.
1
FINE SYNC can only be set in the displayed RGB mode.
*
___
The return value of TLTT
1 becomes 0 when the projector is in the standby mode.
-86
Page 88
Wired Remote Control Terminal Specifications
Specifications of wired remote control input
ø3.5 mm minijack
External: GND
Internal: +3.3V
Function and transmission codes
CONTROL
ITEM
ON
STANDBY
MENU
ƒ
ß
©
ENTER
UNDO
RGB/COMP.
SYSTEM CODE
C1
C2
C3
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
C4
1
1
1
1
1
1
1
1
1
1
C5 C6
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
1
1
1
C7
C8
1
1
0
0
0
0
1
1
0
0
DATA CODE
C9
C10 C11
1
0
1
1
0
1
1
0
0
1
1
1
1
1
1
0
0
1
1
1
0
1
0
1
0
1
1
0
0
1
0
0
0
0
0
0
0
0
0
1
C12
1
0
1
0
0
1
1
1
1
1
JUDGEMENT
C13
C14
0
1
1
1
1
0
0
0
0
1
CODE
1
1
1
1
1
1
1
1
1
1
C15
0
RESIZE
PICTURE POSITION
0
IRIS
0
AUTO SYNC
0
KEYSTONE
0
INPUT 1
0
INPUT 2
0
INPUT 3
0
INPUT 4
0
INPUT 5
0
CONTROL
ITEM
SYSTEM CODE
C1
C2
C3
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
C4
1
1
1
1
1
1
1
1
1
1
C5 C6
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
0
1
0
1
C7
1
0
1
1
1
1
1
1
1
0
DATA CODE
C8
C9
C10 C11
1
1
0
1
0
1
0
1
1
1
0
1
0
1
1
0
0
0
1
0
1
0
1
1
0
1
1
1
1
1
1
0
1
1
1
1
1
1
1
1
Wired remote control function code
LSB MSB
C1 System Code C5 C6 Data Code C13 C14 C15
10110********10
System codes C1 to C5 are fixed at 10110”.
Codes C14 and C15 are reverse confirmation bits, with 10 indicating Front and 01 indicating Rear”.
C12
1
0
0
1
0
0
0
0
0
0
JUDGEMENT
C13
C14
0
0
1
1
1
0
0
0
0
0
CODE
1
1
1
1
1
1
1
1
1
1
C15
0
0
0
0
0
0
0
0
0
0
Sharp remote control signal format
Transmission format: 15-bit format
DDDDDD
67.5 ms 67.5 ms
Wave form of output signal: Output using Pulse Position Modulation
t
0
T
1
T
0001
t = 264 µs Pulse carrier frequency = 37.917 kHz
T0 = 1.05 ms Duty ratio = 1:1
T
1 = 2.10 ms
Transmission control code
15 bit Example of Reverse D to D
C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14
System Address
D to D Common Data Bit Reverse in D
DDDDDDD
D
Function Key Data Bit
Data
Expansion
Mask
C15
Data
Deter-
mination
010
26.4 µs
C11DC20C31C41C50C61C70C80C90C100C110C120C130C141C15
C11DC20C31C41C50C60C71C81C91C101C111C121C131C140C15
t
0
1
Appendix
-87
Page 89
Computer Compatibility Chart
Computer
Multiple signal support
Horizontal Frequency: 15–81 kHz, Vertical Frequency: 43–100 Hz, Pixel Clock: 12–120 MHz
Compatible with sync on green and composite sync signals
SXGA compatible in advanced intelligent compression
AICS (Advanced Intelligent Compression and Expansion System) resizing technology
The following is a list of modes that conform to VESA. However, this projector supports other signals that are not VESA standards.
PC/ MAC/ WS
PC
VGA
SVGA
XGA
Resolution
640 × 350
720 × 350
640 × 400
720 × 400
640 × 480
800 × 600
1,024 × 768
Horizontal Frequency
(kHz)
27.0 60
31.5
37.9
27.0
31.5
27.0
31.5
37.9
27.0
31.5
37.9
26.2
31.5
36.8
37.9
37.5
43.3
47.9
53.0
31.4
35.1
37.9
44.5
48.1
46.9
53.7
56.8
64.0
35.5
40.3
48.4
56.5
60.0
68.7
73.5
77.2
80.6
Vertical
Frequency
(Hz)
70 85 60 70 60 70 85 60 70 85 50 60 70 72 75 85 90
100
50 56 60 70 72 75 85 90
100
43 50 60 70 75 85 90 96
100
VESA
Standard
✔ ✔ ✔
✔ ✔
✔ ✔ ✔
✔ ✔ ✔ ✔
DVI
Support
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
Display
Upscale
Advanced Intelligent
Compres-
sion
PC/ MAC/ WS
PC
MAC
13
MAC
16
MAC
19
MAC
21
PC
(WS)
SGI
(WS)
SUN
(WS)
SXGA
VGA
SVGA
XGA
SXGA
SXGA
Resolution
1,280 ×1,024
640 × 480
832 × 624
1,024 × 768
1,152
1,280
1,280×1,024
1,152
1,152
×
864
1,152
×
882
×
×
×
870
960
900
Horizontal
Frequency
(kHz)
54.3 60
64.0
64.1
67.5
75.7
54.8
65.9
67.4
64.0
34.9
49.6 75
48.4 60
68.5 75
60.0 60
53.5 50
60.9 66
71.9 76
Vertical
Frequency
(Hz)
70 85 60 70 60 72 74 60
67
VESA
Standard
DVI
Support
✔ ✔
✔ ✔ ✔
✔ ✔ ✔ ✔
Display
Advanced Intelligent
Compres-
sion
Upscale
Advanced Intelligent
Compres-
sion
Note
This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this occur, turn off
the LCD display on the notebook computer and output the display data in CRT only mode. Details on how to change display modes can be found in your notebook computers operation manual.
When this projector receives 640 × 350 VESA format VGA signals, 640 × 400 appears on the screen.
When projecting moving image of interlace signals using RGB input, the intended image may not be projected depending on the signal
types. In such cases, use the component, S-video or video input.
DTV
Signal
480I
480P
576I 576P 720P 720P 1080I 1080I
Horizontal Frequency (kHz)
15.8
31.5
15.6
31.3
45.0
37.5
33.8
28.1
Vertical Frequency (Hz)
60 60 50 50 60 50 60 50
DVI Support
✔ ✔ ✔ ✔ ✔
-88
Page 90
Troubleshooting
Problem
No picture and no sound
or projector does not start.
Color is faded or poor.
Picture is blurred;
noise appears.
An unusual sound is
occasionally heard
from the cabinet.
Maintenance
indicator illuminates.
Power indicator and
lamp indicator do not
come on while projecting.
Check Page
Projector power cord is not plugged into the wall outlet. 16
Power to the external connected devices is off.
The selected input mode is wrong. 35
Cables incorrectly connected to rear panel of the projector. 17-26
Remote control batteries have run out. 13
External output has not been set when connecting notebook computer.
The cover of the lamp unit is not installed correctly. 81
The selected Signal Type is wrong. 69
The video signal format of the video equipment is not set correctly.
Bright is set to minimum position. 47
Picture adjustments are incorrectly set. 47
(Video Input only)
Video input system is incorrectly set. 70 (INPUT 1, 2 and 5 only)
Input signal type is incorrectly set. 69
Adjust the focus. 28
The projection distance exceeds the focus range. 30-31
(Computer Input only)
Perform Fine Sync Adjustments (Clock Adjustment) 57
Perform Fine Sync Adjustments (Phase Adjustment) 57
Noise will appear depending on the computer.
The DNR (Digital Noise Reduction) setting is not correct. 50
If the picture is normal, the sound is due to cabinet shrinkage
caused by a room temperature changes. This will not affect operation or performance.
See Maintenance Indicators.78
LED is set to OFF.67
70
-89
Appendix
Page 91
Troubleshooting
CheckProblem Page
Picture is green on
INPUT 1 or 2 COMPO-
NENT.
Picture is pink (no green)
on INPUT 1 or 2 RGB.
Picture is dark.
Picture is too bright and
whitish.
A response code cannot
be received when the
projector was attempted
to be controlled using
RS-232C commands
from a computer during
standby.
Change the input signal type setting. 69
The lamp indicator is blinking in red. Replace the lamp. 78
Picture adjustments are incorrectly set. 47
In the case of transmitting RS-232C commands from a computer 84
during standby, it takes a maximum of 30 seconds for the computer to receive the response code. Set the response code waiting time of the computer to 30 seconds or more.
For SHARP Assistance (U.S.A only)
If you encounter any problems during setup or operation of this projector, first refer to the “Trouble- shooting section on pages 89 and 90. If this operation manual does not answer your question, please call toll free 1-877-DTV-SHARP (1-877-388-7427) for further assistance. Or, send us an e­mail at lcdsupport@sharpsec.com . Our World Wide Web address is http://www.sharpusa.com/ .
-90
Page 92
Specifications
Product type
Model
Video system
Display method
DLP panel
Lens
Projection lamp
S-video input signal
Component input signal
Horizontal resolution
RGB input signal
Video input signal
Computer control signal
Pixel clock
Vertical frequency
Horizontal frequency
Rated voltage
Input current
Rated frequency
Power consumption (normal)
Power consumption(standby)
Heat dissipation
Operating temperature
Storage temperature
Cabinet
I/R carrier frequency
Dimensions (approx.)
Weight (approx.)
Supplied accessories
Replacement parts
Projector XV-Z12000 NTSC 3.58/NTSC 4.43/PAL/PAL-M/PAL-N/PAL 60/SECAM DTV480I/DTV480P/DTV720P/DTV1080I DLP chip, RGB optical shutter method Panel size: 0.8" Display method: Single Panel Digital Micromirror Device (DMD™) by Texas Instruments Drive method: Digital Light Processing (DLP™) No. of dots: 921,600 dots (1,280 [H] × 720 [V]) 1–1.35 × zoom lens, F2.5–8, f = 32.5–44.0 mm 270 W SHP lamp 4-pin Mini DIN connector (INPUT 3) Y (luminance signal): 1.0 Vp-p, sync negative, 75 terminated C (chrominance signal): Burst 0.286 Vp-p, 75 terminated RCA Connector (INPUT 1, 2) Y: 1.0 Vp-p, sync negative, 75 terminated PB: 0.7 Vp-p, 75 terminated PR: 0.7 Vp-p, 75 terminated 520 TV lines (NTSC 3.58 input), 750 TV lines (DTV 720P input) DVI-I terminal: (INPUT 5)/RCA connector: INPUT 1/2 <Digital> Input impedance 50 Input level 250-1000 mV <Analog> Input Impedance 75 Input level 0.7 Vp-p <Synchronization signal>
Separate sync / Composite sync Input level TTL level Input impedance 1 K
Green on sync Input level (Synchronizing input) 0.286 Vp-p Input Impedance 75
RCA Connector: VIDEO (INPUT 4), composite video, 1.0 Vp-p, sync negative, 75 terminated 9-pin D-sub connector (RS-232C Port) 12–120 MHz 43–100 Hz 15–81 kHz AC 100–240 V
3.7 A (When using AC 100 V)
50/60 Hz 365 W About 0.1 W (When using 100 V) 1,400 BTU/hour 41°F to 95°F (+5°C to +35°C) –4°F to 140°F (–20°C to +60°C) Plastic 38 kHz 18 11/16" × 7" × 15 49/50" (475 (W) × 178 (H) × 406 (D) mm) (main body only) 18 11/16" × 7" × 19 1/2" (475 (W) × 178 (H) × 496 (D) mm) (including terminal cover)
20.7 lbs. (9.4 kg)
Remote control, Two AA size batteries, Power cord (9'10", 3.0 m), Terminal cover, Lens cap (attached), SharpVision Manager Software CD-ROM, Projector operation manual, SharpVision Manager operation manual Lamp unit (Lamp/cage module) (BQC-XVZ100005), Remote control (RRMCGA216WJSA), AA size batteries , Power cord (CACCDA024DE01), Lens cap (PCAPH1056CESA), Projector operation manual (TINS-A970WJZZ), (TINS-B097WJZZ)
SharpVision Manager
Terminal cover (CCOVA1985CE03)
Software CD-ROM (UDSKAA040WJZZ),
SharpVision Manager operation manual
,
Appendix
This SHARP projector uses a DMD Chip. This very sophis­ticated panel contains 921,600 pixels. As with any high tech­nology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to.
Specifications are subject to change without notice.
This unit has some inactive pixels within acceptable toler­ances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit. If you have any questions about this matter, please call toll free 1-877-DTV-SHARP (1-877-388-7427).
U.S.A ONLY
-91
Page 93
Dimensions
Units: inches (mm)
Side View Side ViewTop View
Rear View
/50 (406)
49
15
Front View
Bottom View
7 (178)
18 11/16 (475)
-92
Page 94
Glossary
Advanced intelligent compression
High quality resizing of lower and higher resolu­tion images to fit the projectors native resolution.
Aspect Ratio
Width and height ratio of an image. The normal aspect ratio of a computer and video image is 4:3. There are also wide images with an aspect ratio of 16:9 and 21:9.
Auto Sync
Optimizes projected computer images by auto­matically adjusting certain characteristics.
Background
Initial setting image projected when no signal is being output.
Clock
Clock adjustment is used to adjust vertical noise when clock level is incorrect.
CLR Temp (Color temperature)
Function that can be used to adjust the color tem­perature to suit the type of image input to the pro­jector. Decrease the color temperature to create warmer, reddish images for natural flesh tones, or increase to create cooler, bluish images for a brighter picture.
C.M.S. (Color Management System)
Function allows you individually adjust the display characteristics of six colors (R: Red, Y: Yellow, G: Green, C: Cyan, B: Blue, M: Magenta)
Digital Shift Setting
The image can be moved vertically when the im­age display mode is set to SMART STRETCH or CINEMA ZOOM during input of video or DTV sig­nals.
Dot by dot
Mode that projects images in their native resolution.
Gamma
Image quality enhancement function that offers a richer image by brightening the darker portions of the image without altering the brightness of the brighter portions.
IP Mode
The progressive display projects a smoother video image. You can select three different modes: 2D Progressive, 3D Progressive and Film Mode.
Keystone correction
Function to digitally correct a distorted image when the projector is set up at an angle, smoothens out jaggies on keystone images and compresses the image not only horizontally but vertically keeping the 4:3 aspect ratio.
Phase
Phase shift is a timing shift between isomorphic signals with the same resolution. When phase level is incorrect, the projected image typically displays horizontal flicker.
Resize
Allows you to modify or customize the picture dis­play mode to enhance the input image. You can select six different modes: SIDE BAR, SMART STRETCH, CINEMA ZOOM, STRETCH, DOT BY DOT or NORMAL.
Smart Stretch
Mode that stretches the right and left sides of the 4:3 image horizontally while maintaining the as­pect ratio around the center of the image to dis­play it on the WIDE screen.
Stretch
Mode that stretches the 4:3 image horizontally to display it fully on a 16:9 screen.
-93
Appendix
Page 95
Index
2D Progressive .................................................... 49
3D Progressive .................................................... 49
AC socket ............................................................ 16
Adjusting Computer Images ................................ 57
Adjusting the Lens ............................................... 28
Adjusting the Picture............................................ 46
Adjustment buttons .............................................. 43
Adjustment feet .................................................... 27
Aspect ratio .......................................................... 63
Auto Power Off .................................................... 72
Auto Sync Adjustment ......................................... 59
AUTO SYNC button ............................................. 59
Auto Sync Disp .................................................... 60
Background .......................................................... 70
Batteries ............................................................... 13
Ceiling-mount setup............................................. 32
CD-ROM ................................................................ 8
Chroma ................................................................ 55
CINEMA ZOOM ................................................... 63
Clock .................................................................... 57
CLR Temp (Color Temperature) .......................... 47
C.M.S. .................................................................. 54
C.M.S. Position ....................................................54
DC 12V OUTPUT terminal .................................. 11
DFC ...................................................................... 51
Digital Shift........................................................... 66
DNR ..................................................................... 50
DOT BY DOT ....................................................... 63
ENTER button...................................................... 43
Film Mode ............................................................ 49
Fine Sync ............................................................. 57
Focus ring ............................................................ 28
Hue ...................................................................... 55
INPUT 1 terminals ............................................... 18
INPUT 1 – 5 modes ............................................. 35
INPUT 2 terminals ............................................... 18
INPUT 3 terminal ................................................. 17
INPUT 4 terminal ................................................. 17
INPUT 5 terminal ................................................. 19
INPUT button ....................................................... 35
IRIS button ........................................................... 65
Kensington Security Standard connector............ 11
KEYSTONE button .............................................. 38
Keystone correction ............................................. 38
Lamp .................................................................... 80
Lamp indicator ..................................................... 78
Lens cap .............................................................. 10
Lens shift dial ....................................................... 29
LIGHT button ....................................................... 12
Lightness ............................................................. 55
MENU button ....................................................... 42
NORMAL.............................................................. 64
ON button ............................................................ 34
Optional accessories ........................................... 14
OSD Display ........................................................ 68
PDF ........................................................................ 8
Phase ................................................................... 57
PICTURE POSITION button ............................... 46
Power cord ........................................................... 16
Power indicator ....................................................34
PRJ mode ............................................................ 73
IP Mode................................................................ 49
Remote control .................................................... 12
Remote control sensor ........................................ 13
Replacing the lamp .............................................. 80
RESIZE button ..................................................... 62
Reversing/Inverting Projected Images ................ 73
RGB/COMP. button.............................................. 69
RS-232C terminal ................................................ 25
Save Setting ........................................................ 57
Select Setting....................................................... 58
Selecting the on-screen display language .......... 36
SharpVision Manager ............................................ 8
SIDE BAR ............................................................ 63
Signal Info ............................................................ 59
Signal Type .......................................................... 69
SMART STRETCH .............................................. 63
Special Modes ..................................................... 58
STANDBY button ................................................. 37
Status ................................................................... 74
STRETCH ............................................................ 63
Supplied accessories........................................... 14
Target ................................................................... 54
Temperature warning indicator ............................ 78
Terminal cover ..................................................... 11
UNDO button ....................................................... 43
Ventilative holes................................................... 77
Video System....................................................... 70
WIRED R/C JACK ............................................... 26
WIRED REMOTE control input terminal ............. 26
Zoom knob ........................................................... 28
-94
Page 96
VALID IN USA ONLY
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the “Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
Model Specific Section (In-Home Service)
Your Product Model Number & Description:
Warranty Period for this Product:
Additional Item(s) Excluded from Warranty Coverage (if any):
Where to Obtain Service:
What to do to Obtain Service:
XV-Z12000 Projector
(Be sure to have this information available when you need service for your Product.)
One (1) year parts and labor from date of purchase except for the Projector Lamp for which the warranty period is ninety (90) days from date of purchase. After the ninety (90) day warranty period on the Projector Lamp, parts and labor for a lamp replacement are the responsibility of the consumer.
Cleaning of Optical System and/or replacement of any filter. Labor & materials required to remove and reinstall a suspended projector in installations not accessible with a standard (8' step) ladder or ceilings exceeding 12 in height. Labor & materials required to remove and reinstall a projector in complex systems including, but not limited to, projectors installed in custom enclosures, projectors connected to third party control and automation systems, and realignment of projectors installed in mirrored rear projection enclosures.
From a Sharp Authorized Servicer located in the United States. To find the location of the nearest Sharp Authorized Servicer, call Sharp toll free at 1-800-BE-SHARP. Contact your Sharp Authorized Servicer to obtain in-home service for this Product. The Servicer will come to your home and if necessary to remove the Product for repair at the Servicers facility, the Servicer will reinstall it upon completion of repair. Be sure to have Proof of Purchase available.
Appendix
TO OBTAIN PRODUCT INFORMATION, CALL 1-877-DTV-SHARP OR VISIT www.sharpusa.com.
-95
Page 97
VALID IN CANADA ONLY
LIMITED WARRANTY
Consumer Electronics Products
Congratulations on your purchase!
Sharp Electronics of Canada Ltd. (hereinafter called “Sharp”) gives the following express warranty to the first consumer purchaser for this Sharp brand product, when shipped in its original container and sold or distributed in Canada by Sharp or by an Authorized Sharp Dealer:
Sharp warrants that this product is free, under normal use and maintenance, from any defects in material and workmanship. If any such defects should be found in this product within the applicable warranty period, Sharp shall, at its option, repair or replace the product as specified herein.
This warranty shall not apply to: (a) Any defects caused or repairs required as a result of abusive operation, negligence, accident, improper installation or inappropriate
use as outlined in the owner’s manual.
(b) Any Sharp product tampered with, modified, adjusted or repaired by any party other than Sharp, Sharp’s Authorized Service
Centres or Sharp’s Authorized Servicing Dealers.
(c) Damage caused or repairs required as a result of the use with items not specified or approved by Sharp, including but not limited
to head cleaning tapes and chemical cleaning agents.
(d) Any replacement of accessories, glassware, consumable or peripheral items required through normal use of the product including
but not limited to earphones, remote controls, AC adapters, batteries, temperature probe, stylus, trays, filters, belts, ribbons,
cables and paper. (e) Any cosmetic damage to the surface or exterior that has been defaced or caused by normal wear and tear. (f) Any damage caused by external or environmental conditions, including but not limited to transmission line/power line voltage or
liquid spillage. (g) Any product received without appropriate model, serial number and CSA/cUL markings. (h) Any products used for rental or commercial purposes. (i) Any installation, setup and/or programming charges.
Should this Sharp product fail to operate during the warranty period, warranty service may be obtained upon delivery of the Sharp product together with proof of purchase and a copy of this LIMITED WARRANTY statement to an Authorized Sharp Service Centre or an Authorized Sharp Servicing Dealer. In home warranty service may be provided at Sharp’s discretion on any Sharp television with the screen size of 27” or larger and on any Sharp Over The Range Microwave Oven.
This warranty constitutes the entire express warranty granted by Sharp and no other dealer, service centre or their agent or employee is authorized to extend, enlarge or transfer this warranty on behalf of Sharp. To the extent the law permits, Sharp disclaims any and all liability for direct or indirect damages or losses or for any incidental, special or consequential damages or loss of profits resulting from a defect in material or workmanship relating to the product, including damages for the loss of time or use of this Sharp product or the loss of information. The purchaser will be responsible for any removal, reinstallation, transportation and insurance costs incurred. Correction of defects, in the manner and period of time described herein, constitute complete fulfillment of all obligations and responsibilities of Sharp to the purchaser with respect to the product and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise.
WARRANTY PERIODS
Projector 1 year (bulb 90 days)
To obtain the name and address of the nearest Authorized Sharp Service Centre or Dealer, please contact:
SHARP ELECTRONICS OF CANADA LTD. 335 Britannia Road East Mississauga, Ontario L4Z 1W9 (905) 568-7140 Web site: www.sharp.ca
SHARP ELECTRONICS OF CANADA LTD.
-96
Page 98
SHARP CORPORATION
1
Printed on 100% post-consumer recycled paper. Imprimé sur 100% de papier recyclé. Impreso en 100% de papel reciclado de postconsumo. Papel 100% Reciclado - Cuidado do Meio Ambiente.
Printed in Japan Imprimé au Japon Impreso en Japón Impresso no Japão TINS-A970WJZZ
Loading...