Sharp XV-Z10000UL Operation Manual

Download

Page 1

XV-Z10000

OPERATION MANUAL MODE D’EMPLOI MANUAL DE OPERACION MANUAL DE OPERAÇÃO

XV-Z10000

PROJECTOR PROJECTEUR PROYECTOR PROJETOR

ENGLISH ............. -1 – -92

FRANÇAIS ........... -1 – -91

ESPAÑOL ............ -1 – -90

PORTUGUÊS ...... -1 – -90

Page 2

This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC.

Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/68/EWG.

Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE.

Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/EEG

Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.

Quest’ apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC, come emendata dalla direttiva 93/68/EEC.

Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão corrigida pela directiva 93/68/CEE.

Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por medio de la 93/68/CEE.

Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som kompletteras av 93/68/EEC.

Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC.

Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/68/EEC.

SPECIAL NOTE FOR USERS IN THE U.K.

The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked

or and of the same rating as above, which is also indicated on the pin face of the plug, must be used. Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type.

DANGER:

The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 10A socket outlet, as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below:

IMPORTANT:

The wires in the mains lead are coloured in accordance with the following code:

Blue: Neutral

Brown: Live As the colours of the wires in the mains lead of this product may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

• The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured

black.

• The wire which is coloured brown must be connected to the plug terminal which is marked L or

coloured red. Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug. Before replacing the plug cover make sure that:

• If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug.

• The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires.

IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

Page 3

Introduction

-1

Before using the projector, please read this operation manual carefully.

There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector.

1. WARRANTY

This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase.

2. CONSUMER PRODUCT SAFETY ACT

To ensure that you will promptly receive any safety notification of inspection, modification, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.

WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially

careful that children do not stare directly into the beam of light.

WARNING: To reduce the risk of fire or electric shock, do not expose this product to

rain or moisture.

WARNING:

FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER.

NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk or electric shock to persons.

The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

Introduction

ENGLISH

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT REMOVE SCREWS

EXCEPT SPECIFIED USER

SERVICE SCREWS.

See bottom of actual set.

U.S.A. ONLY

IMPORTANT

For your assistance in reporting the loss or theft of your Projector, please record the Serial Number located on the bottom of the projector and retain this information. Before recycling the packaging, please be sure that you have checked the contents of the carton thoroughly against the list of “Supplied accessories” on page 14.

Model No.: XV-Z10000

Serial No.:

Page 4

-2

WARNING:

The cooling fan in this projector continues to run for about 90 seconds after the projector is turned off. During normal operation, when turning the power off always use the power (OFF) button on the projector or on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord. DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.

Caution Concerning the Lamp Replacement

See “Replacing the Lamp” on pages 76-78.

PRODUCT DISPOSAL

This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or, if you are located in the United States of America, the Electronic Industries Alliance: www.eiae.org .

INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

U.S.A. ONLY

Declaration of Conformity

SHARP PROJECTOR, MODEL XV-Z10000 This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Responsible Party:

SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430 TEL: 1-800-BE-SHARP (1-800-237-4277)

U.S.A. ONLY

WARNING:

Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or discompile the contents thereof.

Page 5

Introduction

-3

Outstanding Features

1. High Color Purity and Broad Dynamic Range Due to Advanced Optical Engine

• Newly developed 12° DMD™ chip provides significantly improved opti-

cal efficiency and excellent contrast ratio.

• Newly developed DDR (Double Data Rate) chip eliminates Color Break-

ing phenomena common with previous generation DLP™ projectors.

• Superior image quality with Minolta™ optical lens system.

• Use of 270 W high-output lamp realizes both high color purity and high

brightness. Natural images made possible by high color reproducibility can be created with high-brightness and powerful expression capabilities.

2. Advanced Computer & Video lntegrated Composer Technology

• Realizes vivid images using the latest image quality circuitry.

• New I/P conversion algorithm enhances the performance of the motion detect I/P

conversion.

Extensive improvements on the jagged edges or slanted lines in moving images.

• New Edge Up-Scaling

As a result of reducing jaggies and flickering when up-scaling edges of slanted lines, even signals not reaching a panel resolution of 480I/P can be projected by converting to 720P high-definition images.

• Noise Reduction

Allows for a clear image even with noisy source signals.

• Contrast Control Dynamic Gamma

Improved contrast and natural color gradation by minimizing hue change.

• Color Management System

Color Management System that freely adjusts only specific hues of RGBCMY enables easy adjustment of only specific locations of an image without affecting other portions of the image.

• Gamma Adjustment Function

Gamma Adjustment Function adds adjustments to each RGB gamma curve for finer image adjustment.

3. Low Noise Design

A new optical engine has been developed for this product resulting in minimized fan noise for undisturbed viewing.

4. All Digital Projection

Use of a DVI/HDCP terminal enables all processes from input to signal processing and projection to be performed digitally, resulting in the realization of all-digital projection without any data loss due to analog conversion. This also supports the building of home theaters using HTPC*.

* Abbreviation for Home Theater Personal Computer that enables high-definition DVD playback using a personal

computer.

Page 6

-4

Contents

Introduction

Outstanding Features ......................................... 3

Contents ............................................................... 4

IMPORTANT SAFEGUARDS ............................... 6

How to Access the PDF Operation Manuals of

SharpVision Manager ......................................... 9

Part Names ........................................................ 10

Projector (Front and Top View) ................................ 10

Projector (Rear View) .............................................. 11

Remote Control (Front View)................................... 12

Remote Control (Top View) ..................................... 12

Using the Remote Control ................................ 13

Available Range of the Remote Control ................. 13

Inserting the Batteries .............................................13

Accessories ....................................................... 14

Connections and Setup

Connecting the Projector to Other Devices .... 16

Before Connecting.................................................. 16

Connecting the Power Cord ................................... 16

Connecting to Video Equipment.............................. 17

Connecting the Projector to a Computer ................. 21

Controlling the Projector by a Computer .................23

Using as a Wired Remote Control .......................... 24

Setup .................................................................. 25

Using the Adjustment Feet ..................................... 25

Adjusting the Lens .................................................. 26

Using the Lens Shift ................................................27

Selecting the HIGH CONTRAST/ HIGH

BRIGHTNESS MODE ...........................................27

Setting up the Screen ..............................................28

Screen Size and Projection Distance ......................29

Projecting a Reversed/Inverted Image ................... 30

Basic Operation

Setting with the Buttons

Image Projection ............................................... 32

Basic Procedure ......................................................32

Selecting the On-screen Display Language ........... 34

Keystone Correction and

Vertical Size Adjustment............................. 36

Setting with the Menus

Menu Bar Items ................................................. 38

Using the Menu Screen .................................... 40

Menu Selections (Adjustments) .............................. 40

Menu Selections (Settings) ..................................... 42

Adjusting the Picture ........................................ 44

Adjusting Image Preferences ..................................44

Emphasizing the Contrast ....................................... 45

Selecting the Gamma Position ................................ 45

Selecting the C.M.S. Color ..................................... 45

Progressive Mode.................................................... 46

Picture Setting Function........................................... 47

Adjusting the Gamma ....................................... 48

Selecting the Gamma Position ................................ 48

Adjusting the Gamma .............................................. 49

Color Management System (C. M. S.) .............. 50

Selecting the Color Reproduction Mode ................. 50

Selecting the Target Color ....................................... 50

Setting the Brightness of the Target Color ...............51

Setting the Chromatic Value of the Target Color...... 51

Setting the Hue of the Target Color ........................ 51

Resetting User-Defined Color Settings................... 52

Overview of All Color Settings ................................. 52

Adjusting Computer Images ............................ 53

When Auto Sync is OFF ...........................................53

Saving Adjustment Settings ................................... 53

Selecting Adjustment Settings ................................54

Special Mode Settings ............................................54

Checking the Input Signal .......................................55

Auto Sync Adjustment .............................................55

Auto Sync Display Function ................................... 56

Page 7

Introduction

-5

Easy to Use Functions

Selecting the Picture Display Mode ................ 58

Switchable High Contrast/High

Brightness Mode ......................................... 61

Digital Shift Function ........................................ 62

Subtitle Setting .................................................. 62

Video Digital Noise Reduction

(DNR) System .............................................. 63

Displaying the Lamp Usage Time .................... 63

Setting On-screen Display ............................... 64

Selecting the Signal Type ................................. 65

Setting the Video System ................................. 66

Setting a Background Image............................ 66

Selecting the Economy Mode .......................... 67

Setting the Power Save ...........................................67

RS-232C Off Function .............................................. 67

Automatic Power Off Function .................................68

Selecting the Transmission Speed

(RS-232C) ..................................................... 68

Reversing/Inverting Projected Images ............ 69

Displaying the Adjustment Settings ................ 70

Appendix

Maintenance ...................................................... 72

Cleaning the Ventilative Holes ......................... 73

Maintenance Indicators .................................... 74

Regarding the Lamp ......................................... 76

Lamp ...................................................................... 76

Caution Concerning the Lamp ................................ 76

Replacing the Lamp ................................................76

Removing and Installing the Lamp Unit ................. 77

Resetting the Lamp Timer ....................................... 78

Connecting Pin Assignments .......................... 79

(RS-232C) Specifications and

Command Settings ...................................... 80

Wired Remote Control Terminal

Specifications .............................................. 83

Computer Compatibility Chart ......................... 84

Troubleshooting ................................................ 85

For SHARP Assistance (U.S.A only) ............... 86

Specifications .................................................... 87

Dimensions ........................................................ 88

Glossary ............................................................. 89

Index ................................................................... 90

Page 8

-6

1. Read Instructions

All the safety and operating instructions should be read before the product is operated.

2. Retain Instructions

The safety and operating instructions should be retained for future reference.

3. Heed Warnings

All warnings on the product and in the operating instructions should be adhered to.

4. Follow Instructions

All operating and use instructions should be followed.

5. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6. Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

7. Water and Moisture

Do not use this product near water–for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

8. Accessories

Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

9. Transportation

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

10.Ventilation

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

IMPORTANT SAFEGUARDS

11. Power Sources

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12. Grounding or Polarization

This product is equipped with a three-wire groundingtype plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

14. Lightning

For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the product due to lightning and power-line surges.

15. Overloading

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

16. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

17. Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

CAUTION: Please read all of these instructions before you operate this product and save them for

later use.

Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing.

Page 9

Introduction

-7

18. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen

into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by

following the operating instructions. Adjust only

those controls that are covered by the operating

instructions, as an improper adjustment of other

controls may result in damage and will often

require extensive work by a qualified technician

to restore the product to normal operation. e. If the product has been dropped or damaged in

any way. f. When the product exhibits a distinct change in

performance.

INTELLECTUAL PROPERTY RIGHTS

IMPORTANT

READ BEFORE USING THE PRODUCT

• Digital Light Processing, DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments.

• Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or

other countries.

• PC/AT is a registered trademark of International Business Machines Corporation in the United States.

• Adobe Acrobat is a trademark of Adobe Systems Incorporated.

• Macintosh is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.

• Minolta is a registered trademark of Minolta Co., Ltd.

• All other company or product names are trademarks or registered trademarks of their respective compa-

nies.

19. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

20. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

21. Wall or Ceiling Mounting

This product should be mounted to a wall or ceiling only as recommended by the manufacturer.

22. Heat

This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Page 10

-8

IMPORTANT SAFEGUARDS

Be sure to read the following safeguards when setting up your projector.

Caution concerning the lamp unit

■ Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest Authorized SharpVision Service Center or Dealer for replacement. See “Replacing the Lamp” on pages 76-78.

Cautions concerning the setup of the projector

■ For minimal servicing and to maintain high image quality, SHARP recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environments, the lens must be cleaned more often. As long as the projector is regularly cleaned, use in these environments will not reduce the overall operation life of the unit. Internal cleaning should only be performed by an Authorized SharpVision Service Center or Dealer.

Do not set up the projector in places exposed to direct sunlight or bright light.

■ Position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.

The projector may safely be tilted to a maximum angle of 5 degrees.

■ Placement should be within ±5 degrees.

Do not subject the projector to hard impact and/ or vibration.

■ Take care with the lens so as not to hit or damage the surface of the lens.

Rest your eyes occasionally.

■ Watching the screen for long hours continuously will make your eyes tired. Be sure to occasionally rest your eyes.

Avoid locations with high or low temperature.

■ The operating temperature for the projector is from 41°F to 95°F (+5°C to +35°C).

■ The storage temperature for the projector is from –4°F to 140°F (–20°C to +60°C).

Do not block the intake and exhaust vents.

■ Allow at least 11.8" (30 cm) of space between the exhaust vent and the nearest wall or obstruction.

■ Be sure that the intake vent and the exhaust vent are not obstructed.

■ If the cooling fan becomes obstructed, a protection circuit will automatically turn off the projector. This does not indicate a malfunction. Remove the projector power cord from the wall outlet and wait at least 10 minutes. Place the projector where the intake and exhaust vents are not blocked, plug the power cord back in and turn on the projector. This will return the projector to the normal operating condition.

Cautions regarding the transportation of the projector

■ When transporting the projector, be sure not to subject it to hard impact and/or vibration, as this can result in damage. Take extra caution with the lens. Before moving the projector, be sure to unplug the power cord from the wall outlet, and disconnect any other cables connected to it.

Other connected equipment

■ When connecting other audio-visual equipment or a computer to the projector, make the connections AFTER turning off the projector and the equipment to be connected.

■ Please read the operation manuals of the projector and the equipment to be connected for instructions on how to make the connections.

Temperature monitor function

■ If the projector starts to overheat due to setup problems or blockage of the air vents, “ ” and “ ” will blink in the lower left corner of the picture. If the temperature continues to rise, the lamp will turn off, the temperature warning indicator on the projector will blink, and after a 90-second cooling-off period the power will shut off. Refer to “Maintenance Indicators” on page 74 for details.

Info

• The cooling fan regulates the internal temperature, and its performance is automatically controlled. The sound of the fan may change during projector operation due to changes in the fan speed. This does not indicate malfunction.

• Do not unplug the power cord during projection or cooling fan operation. This can create damage due to the rise in internal temperature, as the cooling fan also stops.

CAUTION PRECAUCIÓN PRÉCAUTION

BQC-XVZ100001

Page 11

Introduction

-9

PDF operation manuals in several languages for the “SharpVision Manager” theater projector software provided are included in the CD-ROM. To utilize these manuals, you need Adobe Acrobat Reader installed on your PC (Windows or Macintosh). If you have not installed Acrobat Reader yet, you can install it from the CD-ROM.

To install Acrobat Reader from the CD-ROM

For Windows:

1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the “My Computer” icon. 3 Double click the “CD-ROM” drive. 4 Double click the “ACROBAT” folder. 5 Double click the language (name of the folder)

that you want to view.

6 Double click the installation program and

follow the instructions on the screen.

For Macintosh:

1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the “CD-ROM” icon. 3 Double click the “ACROBAT” folder. 4 Double click the language (name of the folder)

that you want to view.

5 Double click the installation program and

follow the instructions on the screen.

For other operating systems:

Please download Acrobat Reader from the Internet (http://www.adobe.com).

For other languages:

If you prefer using Acrobat Reader for languages other than those included in the CD-ROM, please download the appropriate version from the Internet.

Accessing the PDF Manuals

For Windows:

1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the “My Computer” icon. 3 Double click the “CD-ROM” drive. 4 Double click the “MANUALS” folder. 5 Double click the language (name of the

folder) that you want to view.

6 Double click the “SVM2” pdf file to access the

SharpVision Manager manual.

Note

• If the desired pdf file cannot be opened by double clicking the mouse, start Acrobat Reader first, then specify the desired file using the “File”, “Open” menu.

• See the “readme.txt” file on the CD-ROM for important information not included in this operation manual.

For Macintosh:

1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the “CD-ROM” icon. 3 Double click the “MANUALS” folder. 4 Double click the language (name of the

folder) that you want to view.

5 Double click the “SVM2” pdf file to access the

SharpVision Manager manual.

How to Access the PDF Operation Manuals of SharpVision Manager

Page 12

-10

Adjustment buttons

(", ', \, |)

For selecting menu items.

ENTER button

For setting items selected

or adjusted on the menu.

UNDO button

For undoing an operation or

returning to the default

settings.

Lens shift dial

Zoom knob

Focus ring

MENU button

For displaying adjustment and setting screens.

RESIZE button

For switching the screen size (SIDE BAR, SMART STRETCH, etc.).

INPUT button

For switching input mode 1, 2, 3, 4 or 5.

Power (ON/OFF) buttons

For turning the power on or off.

Temperature warning indicator

When the internal temperature rises, this indicator will illuminate red.

Lamp replacement indicator

Illuminates blue, indicating normal function. Replace the lamp when the indicator illuminates red.

Power indicator

Illuminates red, when the projector is in standby. When the power is turned on, this indicator will illuminate blue.

HIGH CONTRAST/ HIGH BRIGHTNESS MODE button

For switching between “HIGH CONTRAST MODE” and “HIGH BRIGHTNESS MODE”.

Adjustment foot

Lens cap

Intake vent

Adjustment foot

Remote control sensor

Projector (Front and Top View)

Part Names

Numbers in refer to the main pages in this operation manual where the topic is explained.

Attaching and removing the lens cap

• Press on the two buttons of the lens cap

and attach it on the lens. Then release the buttons to lock it in place.

• Press on the two buttons of the lens cap

and remove it from the lens.

Page 13

Introduction

-11

PUSH!

Remote control

sensor

Kensington Security

Standard connector

INPUT 2 terminals

Terminals for

component and RGB

signals

INPUT 5 terminal

Terminal for DVI

digital, computer

RGB and component

signals.

INPUT 1 terminals

Terminals for

component and

RGB signals

INPUT 3 terminal

Terminal for connecting video equipment with an S-video terminal.

WIRED REMOTE control input terminal

INPUT 4 terminal

For connecting video equipment.

Intake vent

Rubber cap

The terminal cover can be attached after removing the rubber cap.

DC 12V OUTPUT terminal

RS-232C terminal

For controlling projector using a computer.

AC socket

Exhaust vent

Intake vent

Projector (Rear View)

Using the Kensington Lock

This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with the system for instructions on how to use it to secure the projector.

Using the Terminal Cover

When the projector is used on a desktop, high mounted or ceiling mounted, attach the terminal cover (supplied) to hide the connecting cables.

Attaching the Terminal Cover

1 Align the hook on the terminal cover with the insert hole

in the hook at the back of the projector.

2 Press the hook in the direction indicated with the arrow to

fasten the terminal cover to the projector.

3 Insert the terminal cover into the mounting groove on the

projector while pushing the tabs inside the terminal cover to the outside with your fingers.

Removing the rubber cap attached on the projector and attach the clips.

Page 14

-12

Remote Control (Front View)

Part Names

KEYSTONE button

For adjusting Keystone Correction

or Vertical Size setting.

WIRED R/C JACK

For controlling the projector by connecting the remote control to the projector.

Power (ON/OFF) buttons

For turning the power on or off.

MENU button

For displaying adjustment and setting screens.

Adjustment buttons

(', ", \, |)

For selecting menu items.

ENTER button

For setting items selected or

adjusted on the menu.

UNDO button

For undoing an operation or

returning to the default settings.

INPUT buttons

For switching to the respective input modes.

RGB/COMP. button

For switching to the respective

input signal type.

AUTO SYNC button

For automatically adjusting images

when connected to a computer.

Remote control signal transmitters

RESIZE button

For switching the screen size (SIDE BAR, SMART STRETCH, etc.).

PICTURE SETTING button

For selecting the picture memory setting.

Backlight button

For lighting all buttons on the remote control.

Remote Control (Top View)

Page 15

Introduction

-13

45˚

23'(7 m)

30˚

45˚

30˚

Using the Remote Control

■ The remote control can be used to control the projector

within the ranges shown in the illustration.

Note

• The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may differ due to the screen material.

When using the remote control:

• Be sure not to drop, expose to moisture or high temperature.

• The remote control may malfunction under a fluorescent lamp.

Under that circumstance, move the projector away from the fluorescent lamp.

Inserting the Batteries

The batteries (two “AA” size) are included in the package.

1 Pull down the tab on the cover

and remove the cover towards the direction of the arrow.

2 Insert the included batteries.

• Insert the batteries making sure the polarities correctly match the

and

marks inside the battery

compartment.

3 Insert the lower tab of the

cover into the opening, and lower the cover until it clicks in place.

Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.

Caution

• Insert the batteries making sure the polarities correctly match the and marks inside the battery compart- ment.

• Batteries of different types have different properties, therefore do not mix batteries of different types.

• Do not mix new and old batteries.

This may shorten the life of new batteries or may cause old batteries to leak.

• Remove the batteries from the remote control once they have run out, as leaving them can cause them to leak. Battery fluid from leaked batteries is harmful to your skin, therefore be sure to first wipe them and then remove them using a cloth.

• The batteries included with this projector may exhaust over a short period, depending on how they are kept. Be sure to replace them as soon as possible with new batteries when they have run out.

• Remove the batteries from the remote control if you will not be using the remote control for a long time.

Remote control

Available Range of the Remote Control

Remote control

Page 16

-14

Accessories

Remote control RRMCGA128WJSA

Tw o “AA” size batteries

Power cord CACCDA010DE01

3 RCA to 15-pin D-sub cable (9'10'' (3.0m)) AN-C3CP DVI to 15-pin D-sub adaptor (7.9'' (20cm)) AN-A1DV DVI cable (9'10'' (3.0m)) AN-C3DV RS-232C cable (32'10'' (10.0m)) AN-C10RS (null modem, cross type)

Note

• Some of the cables may not be available depending on the region. Please check with your nearest

Authorized SharpVision Service Center or Dealer.

Operation manual (this manual) TINS-A440WJZZA SharpVision Manager operation manual TINS-A452WJZZ

CD-ROM (SharpVision Manager) UDSKAA028WJN1

Lens cap (attached) PCAPH1056CESA

Supplied accessories

Optional accessories

Terminal cover CCOVA1985CE02

Page 17

Connections and Setup

Page 18

-16

Connecting the Projector to Other Devices

Before Connecting

Note

• Before connecting, be sure to turn off both the projector and the devices to be connected. After making all connections, turn on the projector and then the other devices. When connecting a computer, be sure that it is the last device to be turned on after all the connections are made.

• Be sure to read the operation manuals of the devices to be connected before making connections.

This projector can be connected to:

Video equipment:

■ A VCR, Laser disc player or other video equipment (See page 17.)

■ A DVD player or DTV* decoder (See page 18.)

*DTV is the umbrella term used to describe the new digital television system in the United States.

A computer using:

■ DVI to 15-Pin D-sub adapter (See page 21.)

■ A DVI cable (See page 22.)

■ An RS-232C cable (AN-C10RS) (See page 23.)

Connecting the Power Cord

Plug in the supplied power cord into the AC socket on the rear of the projector.

Power cord

Supplied accessory

-16

Page 19

Connections and Setup

-17

Connecting to Video Equipment

S-video cable (commercially available)

Connecting to Video Equipment Using an S-video or a Composite Video Cable

Using an S-video or a composite video cable, a VCR, laser disc player or other video equipment can be connected to INPUT 3 and INPUT 4 input terminals.

Connect the projector to the video equipment using an S-video cable or a composite video cable (both commercially available).

Note

• The INPUT 3 (S-VIDEO) terminal uses a video signal system in which the picture is separated into color and luminance signals to realize a higher-quality image. To view a higher-quality image, use a commercially available S-video cable to connect the INPUT 3 terminal on the projector and the S-video output terminal on the video equipment.

To S-video output terminal

To video output terminal

Composite video cable (commercially available)

VCR or other video equipment

Page 20

Component cable (commercially available)

DVD player or DTV* decoder

Connecting to Component Video Equipment Using a Component Cable (INPUT 1 or 2)

Use a component cable when connecting the component video equipment such as DVD players and DTV* decoders to INPUT 1 or 2 terminal.

DTV is the umbrella term used to describe the new digital television system in the United States.

Connect the projector to the component video equipment using the component cable.

Note

• When connecting the projector to the video equipment in this way, select “Component” for “Signal Type” in the “Options” menu, or select the Component mode by pressing

on the remote control. See

page 65.

• Set the “Resolution” of “Special Modes” to “480P” during input of a 480P signal. See page 54.

Connecting to RGB Video Equipment Using a 5 RCA RGB Cable (INPUT 1 or 2)

Use a 5 RCA RGB cable when connecting the RGB video equipment such as DVD players and DTV* decoders to INPUT 1 or 2 terminal.

Connect the projector to the RGB video equipment using the 5RCA RGB cable.

Note

• When connecting the projector to the video equipment in this way, select “RGB” for “Signal Type” in the “Options” menu, or select the RGB mode by pressing on the remote control. See page 65.

• The (HD/C sync) and (VD) terminals may be used depending on the specifications of the DTV decoder connected to this projector. Please refer to the operation manual of the DTV decoder for details.

To analog RGB output terminal

5 RCA RGB cable (Commercially available)

DVD player or DTV* decoder

To analog component output terminal

Connecting the Projector to Other Devices

-18

Page 21

Connections and Setup

-19

Connecting to Component Video Equipment Using a 3 RCA to 15-pin D-Sub Cable and the DVI to 15-pin D-Sub adaptor (INPUT 5)

Use a 3 RCA to 15-pin D-Sub cable and the DVI to 15-pin D-Sub adaptor when connecting to the INPUT 5 terminal, component video equipment such as DVD players and DTV* decoders.

DTV is the umbrella term used to describe the new digital television system in the United States.

Connect the projector to the video equipment using a 3 RCA to 15-pin D-Sub cable and the DVI to 15-pin D-Sub adaptor.

Note

• Select the input signal type of the video equipment. See page 65.

3 RCA to 15-pin D-sub cable Type: AN-C3CP (9'10" (3.0 m))

DVI to 15-pin D-sub adaptor Type: AN-A1DV (7.9" (20 cm))

Optional accessories

To analog component output terminal

DVD player or DTV* decoder

DVI to 15-pin D-sub adaptor (sold separately)

3 RCA to 15-pin D-sub cable (sold separately)

Page 22

Optional accessory

DVI cable Type:AN-C3DV

(9'10'' (3.0m))

DVI cable (sold separately)

DVD player or DTV* decoder

Connecting to Video Equipment with the DVI Output Terminal Using the DVI Cable

Use the DVI cable when connecting to the INPUT 5 terminal, video equipment with the DVI output terminal such as DVD players and DTV* decoders.

DTV is the umbrella term used to describe the new digital television system in the United States.

Connect the projector to the video equipment using the DVI cable.

Note

• Select the input signal type of the video equipment. See page 65.

Connecting the Projector to Other Devices

-20

Page 23

Connections and Setup

-21

Connecting the Projector to a Computer

Optional accessory

DVI to 15-pin D-sub adaptor Type: AN-A1DV (7.9" (20cm))

Connecting to a Computer Using the DVI to 15-pin D-sub Adaptor and the RGB Cable

Connect the projector to the computer using the DVI to 15-pin D-sub adaptor and the RGB cable.

• Secure the connectors by tightening the thumbscrews.

Note

• See page 84 “Computer Compatibility Chart” for a list of computer signals compatible with the projector. Use with computer signals other than those listed may cause some of the functions not to work.

• When connecting the projector to a computer in this way, select “A.RGB” for “Signal Type” in the “Options” menu, or select the “A.RGB” by pressing

on the re-

mote control. See page 65.

• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Authorized SharpVision Service Center or Dealer.

• Depending on the computer you are using, an image may not be projected unless the signal output setting of the computer is switched to the external output. Refer to the computer operation manual for switching the computer signal output settings.

To RGB output terminal

Notebook computer

RGB Cable (commercially available)

DVI to 15-pin D-sub adaptor (sold separately)

Page 24

-22

Connecting the thumbscrew cables

■ Connect the thumbscrew cable making sure that it fits cor-

rectly into the terminal. Then, firmly secure the connectors by tightening the screws on both sides of the plug.

■

Do not remove the ferrite core attached to the RGB cable.

Ferrite core

“Plug and Play” function

■ This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC

compatible computer will communicate their setting requirements, allowing for quick and easy setup.

■ Before using the “Plug and Play” function, be sure to turn on the projector first and the connected

computer last.

Note

• The DDC “Plug and Play” function of this projector operates only when used in conjunction with a VESA DDC compatible computer.

Optional accessory

DVI cable Type:AN-C3DV

(9'10'' (3.0m))

Desktop computer

To DVI Digital output terminal

DVI cable (sold separately)

Connecting to a Computer Using a DVI Cable (Sold Separately)

Connect the projector to the computer using the DVI cable.

Note

• Switch the signal type to either “A.RGB” or “D.PC RGB” depending on whether the computer output signal is analog or digital. See page 65.

Connecting the Projector to Other Devices

Page 25

Connections and Setup

-23

Controlling the Projector Using an RS-232C Cable

When the RS-232C terminal on the projector is connected to a computer with an RS-232C cable (null modem, cross type, sold separately), the computer can be used to control the projector and check the status of the projector. See page 80 for details.

Connect the projector to the computer using an RS-232C cable.

Note

• Do not connect or disconnect an RS-232C cable to or from the computer while it is on. This may damage your computer.

• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the operation manual of the computer for details.

Optional accessory

Desktop computer

To RS-232C terminal

RS-232C cable (sold separately)

RS-232C cable Type: AN-C10RS (32'10'' (10.0m))

Controlling the Projector by a Computer

Page 26

Connecting the Projector to Other Devices

Using as a Wired Remote Control

Connecting the Remote Control to the Projector

When the remote control cannot be used due to the range or positioning of the projector (rear projection, etc.), connect a ø3.5 mm minijack cable (commercially available or available as Sharp service part QCNW4870CEZZ) from the WIRED R/C JACK on the top of the remote control to the WIRED REMOTE control input terminal.

ø3.5 mm minijack cable (commercially available or available as Sharp service part QCNW-4870CEZZ)

To WIRED R/C JACK

WIRED REMOTE control input terminal

-24

Page 27

Connections and Setup

-25

Setup

Foot releases

Adjustment feet

Using the Adjustment Feet

The height of the projector can be adjusted using the adjustment feet when the projector is placed on an uneven surface or when the screen is slanted. The position of the projected image can be made higher by adjusting the projector when it is in a location lower than the screen.

1 Press the foot releases and lift

the projector to the desired angle.

2 Remove your hands from the

foot releases. Once the adjustment feet have locked in position, release the projector.

• If the screen is at an angle, the adjustment feet can be used to adjust the angle of the image.

Note

• The projector is adjustable up to approximately 5 degrees from the standard position.

• When the height of the projector is adjusted, the image may become distorted (keystoned), depending on the relative positions of the projector and the screen. See page 36 for details on the keystone correction.

Info

• Do not hold the lens when lifting or lowering the projector.

• When lowering the projector, be careful not to get your finger caught in the area between the adjustment foot and the projector.

Page 28

Zoom

out

Zoom in

Zoom knob

Focus ring

Adjusting the Lens

The image is focused and adjusted to the desired size using the focus ring or zoom knob on the projector.

1 Zooming is adjusted by mov-

ing the zoom knob.

2 The focus is adjusted by rotat-

ing the focus ring.

Setup

Zoom Knob

Focus ring

-26

Page 29

Connections and Setup

-27

Down

Lens shift dial

HIGH CONTRAST/ HIGH BRIGHTNESS MODE button

Using the Lens Shift

The height of the projected image can be adjusted within the shift range of the lens by rotating the lens shift dial on the top of the projector.

Note

• Do not turn the lens shift dial beyond the upper limit and lower limit positions. This may cause the projector to malfunction.

Selecting the HIGH CONTRAST/ HIGH BRIGHTNESS MODE

Pressing the HIGH CONTRAST/HIGH BRIGHTNESS MODE button switches between the contrast emphasis mode and brightness emphasis mode. See page 61 for details.

Page 30

-28

90°

Example of Standard Setup

Setting up the Screen

Position the projector perpendicular to the screen with all feet flat and level to achieve an optimal image.

Note

• The projector lens should be centered in the middle of the screen. If the horizontal line passing through the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.

• For optimal image, position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.

• A polarizing screen cannot be used with this projector.

Standard Setup (Front Projection)

■ Place the projector at the required distance from the screenaccording to the desired picture size. (See page

29.) Screen size : 100 inches (254cm) Aspect ratio : 16:9

Side View

Top View

• The distance from the screen to the projector

may vary depending on the size of the screen.

P.29

• The default setting can be used, when placing the

projector in front of the screen. If the projected image is reversed or inverted, readjust the setting to “Front” for “PRJ Mode” in the “Options” menu.

P.69

• Place the projector so that an imaginary horizontal

line that passes through the center of the lens is perpendicular to the screen.

Audience

Setup

Page 31

Connections and Setup

-29

Screen Size and Projection Distance

When using a wide screen (16:9)

In case of displaying the 16:9 picture on the whole of the 16:9 screen.

(Max.) = (0.05058x – 0.0447) × 3.28

(Min.) = (0.03734x – 0.0447) × 3.28

z1 (Upper) = 0 z

(Lower) = –0.45x

Diag. (x)

300" 250" 200" 150" 133" 106" 100"

92" 84" 72" 60" 40"

Width

261" 218" 174" 131" 116"

92" 87" 80" 73" 63" 52" 35"

Height

147" 123"

98" 74" 65" 52" 49" 45" 41" 35" 29" 20"

Maximum (y1) 54'1" (16.5 m) 45'1" (13.7 m)

36' (11.0 m) 26'12" (8.2 m) 23'11" (7.3 m) 18'11" (5.8 m) 17'11" (5.5 m)

16'5" (5.0 m)

15' (4.6 m)

12'10" (3.9 m)

10'8" (3.3 m)

7'1" (2.2 m)

Minimum (y2)

39'11" (12.2 m)

33'3" (10.1 m)

26'7" (8.1 m)

19'11" (6.1 m)

17'7" (5.4 m)

13'11" (4.3 m)

13'2" (4.0 m) 12'1" (3.7 m) 11'1" (3.4 m)

9'6" (2.9 m)

7'10" (2.4 m)

5'2" (1.6 m)

Upper (z1)

0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm)

Screen size (16:9) Projection distance (y)

Distance from the lens center to the lower edge of the screen (z)

Lower (z2)

–12'3" (–374 cm) –10'3" (–311 cm)

–8'2" (–249 cm) –6'2" (–187 cm) –5'5" (–166 cm) –4'4" (–131 cm) –4'1" (–125 cm) –3'9" (–114 cm) –3'5" (–105 cm) –2'11" (–90 cm)

–2'5" (–75 cm) –1'8" (–50 cm)

x : Screen size (diag.) (inches) y : Projection distance (feet) z : Distance from the lens center to the

lower edge of the screen (feet)

When using a normal screen (4:3)

In case of setting the 16:9 picture to the full horizontal width of the 4:3 screen.

y1 (Max.) = (0.05510x – 0.04593) × 3.28 y

(Min.) = (0.04068x – 0.04369) × 3.28

(Upper) = 0

z2 (Lower) = –0.4904x

Diag. (x)

250" 200" 150" 100"

84" 72" 60"

Width

200" 160" 120"

80" 67" 58" 48"

Height

150" 120"

90" 60" 50" 43" 36"

Maximum (y1)

41'4" (12.6 m)

33' (10.1 m)

24'9" (7.5 m) 16'5" (5.0 m) 13'9" (4.2 m)

11'10" (3.6 m)

9'10" (3.0 m)

Minimum (y2) 30'6" (9.3 m) 24'4" (7.4 m) 18'3" (5.6 m) 12'1" (3.7 m) 10'2" (3.1 m)

8'8" (2.6 m) 7'2" (2.2 m)

Upper (z1)

0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm) 0" (0 cm)

Screen size (4:3)

Projection distance (y)

Distance from the lens center to the lower edge of the screen (z)

Lower (z2)

–12'6" (–286 cm)

–10' (–229 cm)

–7'6" (–171 cm)

–5' (–114 cm) –4'2" (–96 cm) –3'7" (–82 cm)

–3' (–69 cm)

x : Screen size (diag.) (inches) y : Projection distance (feet) z : Distance from the lens center to the

lower edge of the screen (feet)

: Screen area : Picture area

: Picture area

Note

• There is an error of ±3% in the formula above.

• Values with a minus (–) sign indicate the distance of the lens center below the

bottom of the screen.

Note

• There is an error of ± 3% in the formula above.

• Values with a minus (–) sign indicate the distance of the lens center below the

bottom of the screen.

The formula for screen size and projection distance

Page 32

-30

Projection from behind the screen

■ Place a translucent screen between the projector and the audience.

■ Reverse the image by setting “Rear” for “PRJ Mode” in the “Options” menu. See

page 69 for use of this function.

Projection using a mirror

■ Place a mirror (normal flat type) in front of the lens.

■ Reverse the image by setting “Rear” for “PRJ Mode” in the

“Options” menu, when the mirror is placed on the audience side. See page 69 for use of this function.

Info

• When using a mirror, be sure to carefully position both the pro-

jector and the mirror so the light does not shine into the eyes of the audience.

Ceiling-mount setup

■ It is recommended that you use the optional Sharp ceiling-mount bracket for this installation.

■ Before mounting the projector, contact your nearest Authorized SharpVision Service Center or Dealer to obtain the recommended ceiling-mount bracket (sold separately). (ANCM250 ceiling-mount bracket, AN-EP101B extension tube for AN-CM250.)

■ Be sure to adjust the position of the projector to match the distance (z) from the lens center position (see page 29) to the lower edge of the image, when mounting the projector on the ceiling.

■ Invert the image by setting “Ceiling + Front” for “PRJ Mode” in the “Options” menu. See page 69 for use of this function.

When using the default setting.

▼On-screen Display

Projecting a Reversed/Inverted Image

The image is reversed.

When using the default setting.

▼On-screen Display

The image is reversed.

When using the default setting.

▼On-screen Display

Setup

The image is inverted.

Page 33

Basic Operation

Page 34

Image Projection

Basic Procedure

Connect the required external equipment to the projector before operating the following procedures.

Info

•

The language preset at the factory is English. If you want to change the on-screen display to another language, reset the language according to the procedure on page

1 Plug the power cord into the

wall outlet.

• The power indicator illuminates red, and the projector enters standby mode.

2 Press on the remote control

on the projector.

• The power indicator illuminates blue. After the lamp replacement indicator illuminates, the projector is ready to start operation.

Note

• The lamp replacement indicator illuminates, indicating the status of the lamp.

Blue: The lamp is ready. Blue blinking: The lamp is

warming up.

Red:

The lamp should be replaced.

• If the power is turned off and immediately switched on again, the lamp replacement indicator may take time to illuminate.

• When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds after the power has been turned on, and then transmit the commands.

-32

INPUT button

Power (ON) button

Power (OFF) button

MENU button

", ',\, | buttons

ENTER button

Power (ON) button

INPUT buttons

', ", \, | buttons

MENU button

ENTER

button

Power (OFF)

button

Lamp replacement indicator

Power indicator

Page 35

Basic Operation

-33

3 Press , , , or

on the remote control or on the projector to select the INPUT mode.

•

After pressing once on the projector, use

to select the desired input mode.

Note

• When no signal is received, “NO SIGNAL” will be displayed. When a signal that the projector is not preset to receive is received, “NOT REG.” will be displayed.

• The INPUT mode is not displayed when “OSD display” is set to “Level A” or “Level B”. (See page 64.)

About the INPUT modes

"On-screen Display (Example)

Using RGB*

Using Component

INPUT 2 mode

Using Component

INPUT 1 mode

INPUT 3 mode

INPUT 4 mode

Using RGB*

➝

➝➝

➝

INPUT 5 mode

➝

* Input the RGB signal of the DTV, not

the computer.

Using S-Video

Using Video

Using Analog RGB

The display varies according to the “Signal Type” with the INPUT 5. The diagram shown above is the example of having selected “Analog RGB”.

Used for projecting images from equipment that sends component signals or RGB signals connected to the INPUT 1 or 2 terminals.

Used for projecting images from equipment connected to the S-VIDEO input terminal.

Used for projecting images from equipment connected to the VIDEO input terminal. Used for projecting images from equipment connected to the DVI input terminal.

INPUT 1 INPUT 2 (

Compo-

nent

/RGB*

)

INPUT 3 (S-Video)

INPUT 4 (Video)

INPUT 5 (Digital PC RGB/ Digital PC Component/ Digital Video RGB/Digital Video Component/ Analog RGB/ Analog Component)

Page 36

Image Projection

Power (ON) button

4 Press on the remote control

on the projector, then

press

or again while the

confirmation message is displayed, to turn off the projector.

Note

• If you accidentally pressed and do not want to turn off the power, wait until the confirmation message disappears.

Info

• Do not unplug the power cord during projection or cooling fan operation. This can cause damage due to the rise in internal temperature, as the cooling fan also stops.

• When connected to equipment such as an amplifier, be sure to turn off the power to the equipment connected first and then to the projector.

Selecting the On-screen Display Language

• The on-screen display language of the projector can be set to English, German, Spanish, Dutch, French, Italian, Swedish, Portuguese, Chinese, Korean or Japanese.

1 Press .

• The menu will be displayed.

2 Press \ or | to select “Lan-

guage”.

MENU button

', ", \, | buttons

-34

Power (OFF)

button

ENTER button

Page 37

Basic Operation

-35

3 Press ' or " to select the de-

sired language, and then press

4 Press .

• The desired language will be set as the on-screen display.

Page 38

Keystone Correction and Vertical Size Adjustment

Correcting Trapezoidal Distortion and Adjusting the Vertical Size of the Picture

This function allows for Keystone (On-screen Trapezoidal Distortion) Correction and the adjustment of the vertical size of the picture.

Note

• When the image is projected either from top or from bottom toward the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction.

• The Keystone Correction can be adjusted up to angle of approximately ±20 degrees.

• There are some input signal in which “KEYSTONE” does not work.

1 Press .

• Each time is pressed, the settings toggles as shown on the right.

2 Press ', ", \ and | to adjust

the Keystone correction.

• If you want to make more detailed corrections, press

to display the test

pattern, and then press

\ and

| to make the adjustments.

Note

•

Since the trapezoidal distortion of the image can be corrected up to an angle of approximately ±20 degrees, the actual screen can be diagonally set up to that angle as well.

•

Press to cancel Keystone Correction.

• Straight lines or the edges of images may appear jagged while adjusting the image.

KEYSTONE button

UNDO button

ENTER button

Normal screen

Keystone Correction screen

Compresses upper side.

Compresses lower side.

Test pattern

', ", \, | buttons

Vertical size adjustment screen

* “V-SIZE” is not dis-

played when the value of “KEYSTONE” is “0”.

-36

Page 39

Basic Operation

-37

Ajuste de Tamanho Vertical

A razão parente da tela poderá variar quando a função de deslocamento da lente é usada em combinação com a função Correção Trapezoidal. Neste caso, ajuste a razão aparente usando o ajuste de tamanho vertical.

Tecla UNDO

Premindo ' aumenta o tamanho vertical da

imagem.

Aperte para reposicionar a imagem.

Premindo " diminui o tamanho vertical da

imagem.

Aperte para reposicionar a imagem.

3 When adjusting vertical size,

pressing

again displays the vertical size adjustment menu.

4 Press "and ' to adjust the

vertical size of the picture, and press

• See below for details about the verti-

cal size screen.

Page 40

-38

Menu Bar Items

This list shows the items that can be set in the projector.

■ INPUT 1 / 2 / 5 Mode

*In INPUT 5, the items in “Signal Type” are “D. PC RGB”, “D. PC Comp.”, “D. Video RGB”, “D. Video Comp.”

“A. RGB” and “A. Comp.”.

Note

• The resolution, vertical frequency and horizontal frequency figures displayed above are for example purposes only.

• Picture adjustment settings differ depending on the type of input signal.

Signal Type

RGB Component

Standard Black Detail Brighten Custom 1 Custom 2 SVM Gamma

Standard Custom 1 Custom 2 Custom 3

+30–30

115005500

Main menu Sub menu

Contrast

Bright

Color

Tint

Sharp

Picture Setting

CLR Temp

Reset

White Emphasis [ON/OFF]

Gamma Position

Color Selected

Progressive Mode

2D Progressive 3D Progressive Film Mode

Picture

Page 44

+30–30

Custom 3Custom 1

+30–30

Color Selected

Target

Lightness

Chroma

Hue

Reset (This Color)

Reset (All Colors)

View Settings

R-Gamma

G-Gamma

B-Gamma

R-Gain

G-Gain

B-Gain

R-Offset

G-Offset

B-Offset

Reset

[R] Red [Y] Yellow [G] Green [C] Cyan [B] Blue [M] Magenta

C.M.S.

Page 50

Gamma Position Standard

Black Detail Brighten Custom 1 Custom 2 SVM Gamma

Gamma

Page 48

Standard

Memory 5Memory 1

INPUT1 / 2 / 5 Memory

+150–150

+60–60

1 2

•

1 2

•

1 2 3 4

•

Resolution 1024 × 864 1152 × 864 1152 × 870 1152 × 882

Resolution 1024 × 768 800 × 600

Vert Freq

60 Hz 75 Hz

Resolution 1024 × 768

800 × 600

Vert Freq

60 Hz 75 Hz

1024 × 768

48.4 KHz 60 Hz

Fine Sync

Page 53

Clock

Phase

H-Pos

V-Pos

Reset

Save Setting

Select Setting

Special Modes

Signal Info

Auto Sync

Auto Sync Disp [ON/OFF]

Resolution Hor Freq Vert Freq

OFF Normal High Speed

Options

Page 62

Reset

Lamp Timer

DNR

OSD Display

Background

Economy Mode

Power Save [ON/OFF] RS-232C Port [ON/OFF] Auto Power Off [ON/OFF]

OFF Level 1

Normal Level A Level B

Blue None

PRJ Mode

Subtitle

Front Ceiling + Front Rear Ceiling + Rear

RS-232C

9600 bps 38400 bps 115200 bps

Level 3

English Deutsch Español Nederlands Français Italiano Svenska Português

Language

Page 34

Status

Page 70

Digi. Shift

+30–30

Page 41

Basic Operation

-39

■ INPUT 3 / 4 Mode

English Deutsch Español Nederlands Français Italiano Svenska Português

Page 70

+30–30

115005500

Main menu Sub menu

Picture Page 44

Contrast

Bright

Color

Tint

Sharp

CLR Temp

Reset

Progressive Mode

2D Progressive 3D Progressive Film Mode

PRJ Mode

Front Ceiling + Front Rear Ceiling + Rear

RS-232C

9600 bps 38400 bps 115200 bps

Language

Page 34

Status

+30–30

Custom 3Custom 1

+30–30

Color Selected

Target

Lightness

Chroma

Hue

Reset (This Color)

Reset (All Colors)

View Settings

[R] Red [Y] Yellow [G] Green [C] Cyan [B] Blue [M] Magenta

C.M.S.

Page 50

Standard

DNR

OSD Display

Video System

Background

OFF Level 1

Normal Level A Level B

Auto PAL (50/60Hz) SECAM NTSC4.43 NTSC3.58 PAL-M PAL-N

Blue None

Economy Mode

Level 3

Options

Page 62

Power Save [ON/OFF] RS-232C Port [ON/OFF] Auto Power Off [ON/OFF]

Standard Black Detail Brighten Custom 1 Custom 2 SVM Gamma

Standard Custom 1 Custom 2 Custom 3

White Emphasis [ON/OFF]

Gamma Position

Color Selected

Picture Setting

Memory 5Memory 1

INPUT3 / 4 Memory

Digi. Shift

Subtitle

Reset

Lamp Timer

R-Gamma

G-Gamma

B-Gamma

R-Gain

G-Gain

B-Gain

R-Offset

G-Offset

B-Offset

Reset

Gamma Position Standard

Black Detail Brighten Custom 1 Custom 2 SVM Gamma

Gamma

Page 48

+30–30

Page 42

This projector has two sets of menu screens that allow you to adjust the image and various projector settings. You can operate the menus from the projector or remote control using the following procedure.

Using the Menu Screen

Menu screen for INPUT 1, INPUT 2 or INPUT 5 RGB mode

Menu screen for INPUT 3, INPUT 4 or INPUT 5 VIDEO Mode

Menu Bar (Main Menu)

"Menu Screen

Menu Selections (Adjustments)

1 Press .

• The menu screen is displayed.

Note

• The “Picture” menu screen for the selected input mode is displayed.

• The on-screen display shown on the lower right is displayed when the INPUT 1, 2 or 5 mode is selected while RGB signals are input.

Menu Bar (Main Menu)

MENU button

buttons

ENTER button

MENU button

ENTER button

buttons

-40

Page 43

Basic Operation

-41

2 Press

\ or

| to select the

menu you want to adjust.

Note

• For details on the menus, see the tree charts on pages 38 and 39.

3 Press

" or

' to select the item

you want to adjust.

Note

• To display a single adjustment item, press

after selecting the item. Only the menu bar and the selected adjustment item will be displayed. Then if you press " or ', the following item (“Bright” after “Contrast”) will be displayed.

• Press

to return to the previous

screen.

4 Press

\ or

| to adjust the item

selected.

• The adjustment is stored.

5 Press .

• The menu screen will disappear.

Page 44

▼ Menu screen

Menu Selections (Settings)

1 Press .

• The menu screen is displayed.

Note

• The “Picture” menu screen for the selected input mode is displayed.

• The on-screen displays shown on the lower right are displayed when INPUT 1, 2 or 5 mode is selected while RGB signals are input.

2 Press

\ or

| to select the

menu you want to adjust.

Note

• For details on the menus, see the tree charts on pages 38 and 39.

3 Press

" or

' to select the

item you want to set.

Note

• Press to return to the previous screen.

• In some menus, select the icon using “ ”.

Using the Menu Screen

MENU button

buttons

ENTER button

MENU button

ENTER button

buttons

Sub menu

-42

Page 45

Basic Operation

-43

Sub menu

4 Press

• The cursor shifts to the sub menu.

5 Press

" or

' to select the set-

ting of the item displayed in the sub menu.

6 Press .

• The item selected is set.

Note

• Some adjustment items will display a confirmation message. When setting an item, press \ or | to select “Ye s ” or “OK” and then press .

• Use to select “ON” or “OFF” for the item of “Economy Mode”.

7 Press .

• The menu will disappear.

Page 46

Adjusting the Picture

You can adjust the projector’s picture to your preferences with the following picture settings.

Adjusting Image Preferences

Note

• First select “INPUT # Memory” when you want to save the “Picture” menu settings. See page 47 for details.

Adjust the “Picture” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Note

• Picture adjustment settings differ depending on the type of input signal.

• The picture adjustments can be stored separately in each input mode.

• Some items may not be adjustable depending on the combination of the INPUT mode and “Signal Type” setting.

• To reset all adjustment items, select “Re- set” and press

Contrast

Bright

Color

Tint

Sharp

CLR Temp

For adjusting the contrast level

For adjusting the brightness of an image

For adjusting the color intensity of an image

For adjusting the tones of an image

For making sharper or softer the contour of an image

For adjusting the color temperature of an image

For less contrast

For less brightness

For less color intensity

Skin tones become purplish

For less sharpness Decreases color

temperature for warmer, reddish, incandescentlike images.

For more contrast

For more brightness

For more color intensity

Skin tones become greenish

For more sharpness Increases color

temperature for cooler, bluish, fluorescent-like images.

Selected Item Description

\ button | button

-44

Page 47

Basic Operation

-45

Emphasizing the Contrast

This function emphasizes the bright portions of images to obtain a higher contrast image.

Select “White Emphasis” in the “Picture” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Note

• ON Emphasizes the bright portions of images.

• OFF Disables “White Emphasis”.

Selecting the C.M.S. Color

This function allows you to select the desired color reproduction mode.

Select “Color Selected” in the “Picture” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Note

• Color can be adjusted in greater detail with “C.M.S.” on the menu screen. See page 50 for details.

Selecting the Gamma Position

This function allows you to select the desired gamma position.

Select “Gamma Position” in the “Picture” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Note

• Gamma can be adjusted in greater detail with “Gamma” on the menu screen. See page 48 for details.

Page 48

Progressive Mode

This function allows you to select the progressive display of a video signal. The progressive display projects a smoother video image.

Select “Progressive Mode” in the “Picture” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Note

• 2D Progressive This function is useful to display fastmoving images such as sports and action films. This mode optimizes the image in a displayed frame.

•

3D Progressive This function is useful to display relatively slow-moving images such as drama and documentary more clearly. This mode optimizes the image by estimating the movement of a number of preceding and succeeding frames.

•

Film Mode Reproduces the image of film source clearly. Displays the optimized image of film transformed with three-two pull down (NTSC and PAL60Hz) or two-two pull down (PAL50Hz and SECAM) enhancement to progressive mode images. * The film source is a digital video record-

ing with the original encoded as is at 24 frames/second. The projector can convert this film source to progressive video at 60 frames/second with NTSC and PAL60Hz or at 50 frames/second with PAL50Hz and SECAM to play back a high-definition image.

• When using progressive inputs, these inputs are directly displayed so that 2D Progressive, 3D Progressive and Film Mode cannot be selected. These modes can be selected in interlace signals other than 1080

• In NTSC or PAL60Hz, even if the 3D Progressive mode has been set, the threetwo pull down enhancement will be enabled automatically, when the film source has been entered.

• In PAL50Hz or SECAM, the two-two pull down enhancement will be enabled only in the Film Mode, when the film source has been entered.

Adjusting the Picture

-46

Page 49

Basic Operation

-47

Picture Setting Function

This function stores all items set in “Picture”. Five settings can be stored separately in “Memory 1” to “Memory 5”. Each stored setting is reassigned to each input mode (INPUT 1 to INPUT 5). Even when the input mode or signal is changed, you can easily select optimal settings from the stored settings.

■ When Saving: Select “Memory #” or “INPUT # Memory” before setting on the “Picture” menu.

Select “Picture Setting” in the “Picture” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

■ When Recalling Saved Settings: When a saved memory number is selected, the “Picture” menu settings change accordingly.

Note

• The items of “Picture Setting” can be se-

lected directly by pressing

. The items change in the order of “Memory 1” – “Memory 5” and then “INPUT #

Memory” each time

is pressed.

■ When Changing Saved Settings: When changing the saved “Picture” menu settings, select the memory number first.

PICTURE SETTING button

Description

Settings of all items in “Picture” can be stored for the respective input modes. The stored settings can be selected in any input modes.

Besides “Memory 1” to “Memory 5”, other settings can be stored for each input mode. “INPUT 1-5 Memory” can be selected for each input mode.

Selected item

Memory 1

Memory 5

INPUT 1 Memory

INPUT 5 Memory

Page 50

Adjusting the Gamma

Use this function to select the gamma position and adjust the gamma curve for finer image adjustment.

Selecting the Gamma Position

Select “Gamma Position” in the “Gamma” menu on the menu screen.

➝For operating the menu screen, see pages 40 to 43.

Note

• The gamma position you make the set-

ting in this menu for can be selected in the “Gamma Position” in the “Picture” menu.

• Select “Custom 1” or “Custom 2” to make

the more detailed gamma setting.

• For selecting “SVM Gamma”, refer to the

SharpVison Manager operation manual (supplied).

Description For Standard picture.

Gives greater depth to darker portions of image.

Brightens darker portions of image.

Allows you to adjust the gamma curve for each of RGB.

Allows you to adjust gamma value using SharpVision Manager Software.

Selected item Standard

Black Detail

Brighten

Custom 1–2

SVM Gamma

Standard Black Detail Brighten

SVM Gamma Custom 2 Custom 1

-48

Page 51

Basic Operation

-49

Adjusting the Gamma

Adjust the gamma curve to suit your preferences. These gamma values can be adjusted only when the gamma position is set to “Custom 1” or “Custom 2”.

Select the gamma item in the “Gamma” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Selected Item Description

button

R-Gamma (Red Gamma)

G-Gamma (Green Gamma)

B-Gamma (Blue Gamma)

R-Gain (Red Gain)

G-Gain (Green Gain)

B-Gain (Blue Gain)

R-Offset (Red Offset)

G-Offset (Green Offset)

B-Offset (Blue Offset)

For adjusting the display characteristic of red color

For adjusting the display characteristic of green color

For adjusting the display characteristic of blue color

For adjusting the contrast level of red color

For adjusting the contrast level of green color

For adjusting the contrast level of blue color

For adjusting the brightness level of red color

For adjusting the brightness level of green color

For adjusting the brightness level of blue color

For giving greater depth to brighter portion of image in red color.

For giving greater depth to brighter portion of image in green color.

For giving greater depth to brighter portion of image in blue color.

For less contrast in red color

For less contrast in green color

For less contrast in blue color

For less brightness in red color

For less brightness in green color

For less brightness in blue color

For giving greater depth to darker portion of image in red color.

For giving greater depth to darker portion of image in green color.

For giving greater depth to darker portion of image in blue color.

For more contrast in red color

For more contrast in green color

For more contrast in blue color

For more brightness in red color

For more brightness in green color

For more brightness in blue color

Page 52

Color Management System (C. M. S.)

This function allows you to individually adjust the display characteristics of six colors (R: Red, Y: Yellow, G: Green, C: Cyan, B: Blue, M: Magenta) .

Red Cyan

Yellow Blue

Green Magenta

Selecting the Color Reproduction Mode

Select “Color Selected” in the “C.M.S.” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Note

• If “Standard” is selected for “Color Se- lected”, other items (e.g., Target) cannot be adjusted.

Selecting the Target Color

Select “Target” in the “C.M.S.” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Description

Sharp default setting

“Lightness”, “Chroma” and “Hue” can be adjusted for each

of the six colors.

Selected item Standard Custom 1-3

-50

Page 53

Basic Operation

-51

Setting the Brightness of the Target Color

Select “Lightness” in the “C.M.S.” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Setting the Chromatic Value of the Target Color

Select “Chroma” in the “C.M.S.” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Setting the Hue of the Target Color

Select “Hue” in the “C.M.S.” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Page 54

Color Management System (C.M.S.)

Resetting User-Defined Color Settings

Select “Reset (This Color)” or “Reset (All Colors)” in the “C.M.S.” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Overview of All Color Settings

Select “View Settings” in the “C.M.S.” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Description

“Lightness”, “Chroma” and “Hue” of the color selected for “Target” are reset.

“Lightness”, “Chroma” and “Hue” of all colors are reset.

Selected item Reset

(This Color)

Reset (All Colors)

-52

Page 55

Basic Operation

-53

Adjusting Computer Images

Use the Fine Sync function in case of irregularities such as vertical stripes or flickering in portions of the screen.

When Auto Sync is OFF

When “Auto Sync” is “OFF”, interference such as flickering or vertical stripes may occur if displaying tilings or vertical stripes. Should this occur, adjust “Clock”, “Phase”, “H-Pos” and “V-Pos” for obtaining an opti- mum image.

Select “Clock”, “Phase”, “H-Pos” or “V- Pos” in the “Fine Sync” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Note

• Computer image adjustments can be made easily by pressing

. See page 55 for

details.

Saving Adjustment Settings

This projector allows you to store up to seven adjustment settings for use with various computers.

Select “Save Setting” in the “Fine Sync” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Selected Item Description

Clock

Phase

H-Pos

V-Po s

Adjusts vertical noise.

Adjusts horizontal noise (similar to tracking on your VCR).

Centers the on-screen image by moving it to the left or right.

Centers the on-screen image by moving it up or down.

Page 56

Selecting Adjustment Settings

Adjustment settings stored in the projector can be easily accessed.

Select “Select Setting” in the “Fine Sync” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Note

• If a memory position has not been set, a resolution and frequency setting will not be displayed.

• When selecting a stored adjustment setting with “Select Setting”, you can set the projector in the stored adjustments.

Special Mode Settings

Ordinarily, the type of input signal is detected and the correct resolution mode is automatically selected. However, for some signals, the optimal resolution mode in “Special Modes” on the “Fine Sync” menu screen may need to be selected to match the computer display mode.

Set the resolution by selecting “Special Modes” in the “Fine Sync” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Note

• Avoid displaying computer patterns which repeat every other line (horizontal stripes). (Flickering may occur, making the image hard to see.)

• When a DVD player or Digital Video is connected, select 480P as the input signal.

• See “Checking the Input Signal” on the next page for information on the currently selected input signal.

-54

Adjusting Computer Images

Page 57

Basic Operation

-55

Checking the Input Signal

This function allows you to check the current input signal information.

Select “Signal Info” in the “Fine Sync” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Auto Sync Adjustment

Used to automatically adjust a computer image.

Select “Auto Sync” in the “Fine Sync” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Note

When setting to “ Normal” or “

High Speed”:

• Auto Sync adjustment will occur when the projector is turned on or when the inputs are switched, when connected to a computer.

Manual adjustments should be performed:

• When the optimum image cannot be achieved with Auto Sync adjustment. See page 53.

• Auto Sync adjustment may take some time to complete, depending on the image of the computer connected to the projector.

• When setting “Auto Sync” to “OFF” or “High Speed”, and if

is pressed Auto Sync will be executed in “High Speed” mode. If the button is pressed again within one minute, Auto Sync will be executed in “Normal” mode.

AUTO SYNC button

Screen display during Auto Sync

Page 58

Auto Sync Display Function

Used to set the screen displayed during Auto Sync.

Select “Auto Sync Disp” in the “Fine Sync” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Description

The image set as a background image is projected.

The computer image being adjusted is displayed.

Selected item

-56

Adjusting Computer Images

Page 59

Easy to Use Functions

Page 60

-58

Selecting the Picture Display Mode

Switching the Picture Display Using Different Input Signals

Press .

• Each time is pressed, the display changes as shown on pages 59 and 60.

Info

• In the Dot by Dot Mode, images are displayed in the original resolution, therefore they will not be enlarged.

• To return to the standard image, press while “RESIZE” is displayed on the screen.

This function allows you to modify or customize the picture display mode to enhance the input image. Depending on the input signal, you can choose “SIDE BAR”, “SMART STRETCH”, “CINEMA ZOOM”, “STRETCH”, “NORMAL” or “DOT BY DOT” image.

RESIZE button

Screen display of the picture display mode

-58

RESIZE button

Page 61

Easy to Use Functions

-59

VIDEO

• Select “DOT BY DOT” during 720P input when viewing 720P output from a computer.

• 720P switches between “STRETCH” and “DOT BY DOT”. “STRETCH” is fixed when 1080

I signal is entered.

• “Digi. Shift” and “Subtitle” only move when in the “SMART STRETCH” and “CINEMA ZOOM” modes.

960 ⳯ 720 1280 ⳯ 720

480I

480P

576I

576P

NTSC

PAL

SECAM

960 ⳯ 720 1280 ⳯ 720480P

––720P

––

1280 ⳯ 720

SIDE BAR STRETCH

CINEMA

ZOOM

SMART

STRETCH

1280 ⳯ 720

–

1280 ⳯ 720

–

DOT BY DOT

1280 ⳯ 720

–1080I

For 4:3

aspect ratio

For 16:9

aspect ratio

480I 480P 540P 576I 576P

NTSC

PAL

SECAM

540P 1080I

720P

Input Signal

SIDE BAR

SMART STRETCH

Output screen image

STRETCH DOT BY DOTCINEMA ZOOM

4:3 aspect ratio

Letterbox

16:9 aspect ratio

Squeeze

Page 62

-60

COMPUTER

• “NORMAL” is fixed when XGA (1024 × 768) signals are entered.

960 ⳯ 720 800 ⳯ 600 SVGA (800 ⳯ 600)

NORMAL DOT BY DOT

For 4:3

aspect ratio

For without

4:3 aspect ratio

960 ⳯ 720 1024 ⳯ 720XGA (1024 ⳯ 768)

960 ⳯ 720 1280 ⳯ 720SXGA (1280 ⳯ 960)

900 ⳯ 720 1280 ⳯ 720SXGA (1280 ⳯ 1024)

VGA

SVGA

XGA

SXGA

Input Signal

NORMAL

Output screen image

DOT BY DOT

4:3 aspect ratio (640 ⳯ 480)

4:3 aspect ratio (800 ⳯ 600)

4:3 aspect ratio (1024 ⳯ 768)

5:4 aspect ratio (1280 ⳯ 1024)

Selecting the Picture Display Mode

Page 63

Easy to Use Functions

-61

HIGH CONTRAST/

HIGH BRIGHTNESS MODE

button

Operating the Theater Mode Function

Press the HIGH CONTRAST/HIGH BRIGHTNESS MODE button to select the “HIGH CONTRAST MODE” or “HIGH BRIGHTNESS MODE”.

Note

• The projector is set to the “HIGH CON- TRAST MODE” when shipped from the factory.

Switchable High Contrast/High Brightness Mode

This function controls the quantity of the projected light and the contrast of the image. It can be operated using the HIGH CONTRAST/HIGH BRIGHTNESS MODE button on the projector. Set “HIGH BRIGHTNESS MODE” when the projector is used in a relatively bright room.

Selected mode

HIGH CONTRAST

MODE

HIGH BRIGHTNESS

MODE

Description

This mode is

recommended for dark

environments.

This mode is

recommended for

bright environments.

Page 64

Digital Shift Function

For easier viewing, this function shifts the entire image projected on the screen up or down when projecting 16:9 images from DVD players and DTV* decoders. * DTV is the umbrella term used to describe the new digital television system in the United States.

Adjusting the Digital Shift

Select “Digi. Shift” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Note

• The Digital Shift Function works with the SMART STRETCH and CINEMA ZOOM screen. For details, see pages 59 and 60.

Subtitle Setting

With this function, you can adjust the vertical size of the display to allow for subtitles.

Adjusting the Vertical Size of the Display

Select “Subtitle” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Note

• When changing the screen with the Subtitle setting, not only the bottom of the screen rises, but also the upper part is changed to a certain point.

• The subtitle setting can be adjusted more effectively with the Digital Shift function.

• The subtitle setting can be made only with the SMART STRETCH and CINEMA ZOOM screen. For details, see pages 59 and 60.

-62

Page 65

Easy to Use Functions

-63

Video Digital Noise Reduction (DNR) System

Reducing Image Noise

Select “DNR” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Note

• Set a level so as to view a clearer picture.

Make sure to set DNR to “OFF” in the following cases:

• When the image is blurry.

• When the contours and colors of moving

images drag.

• When TV broadcasts with weak signals are projected.

Note

• This function is available with INPUT 1, 2 (480

I, 480P, 580I and 580P signals) and

INPUT 3, 4 (all signals).

Digital Noise Reduction (DNR) provides high quality images with minimal dot crawl and cross color noise.

Confirming the Lamp Usage Time

This function allows you to check the lamp usage time.

Select “Options” menu to see the lamp usage time.

Note

• It is recommended that the lamp be changed after approximately 1,900 cumulative hours of use.

Displaying the Lamp Usage Time

Lamp Usage Time

Page 66

This function allows you to turn on or off the on-screen messages. When setting “ Level A” or “ Level B” in “OSD Display”, the input mode display (e.g. INPUT 1) will not appear, even if the INPUT button is pressed.

Setting On-screen Display

Selected Item

Normal

Level A

Level B

Description

All On-screen Displays are displayed.

Input and Auto Sync are not displayed.

All On-screen Displays are not displayed. (except for Menu, On-screen Displays displayed when the KEYSTONE button is pressed, and warning displays (Power off/Temp./Change The Lamp., etc.))

Turning Off the On-screen Display

Select “OSD Display” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

-64

Page 67

Easy to Use Functions

-65

For INPUT 5

Set when RGB signals are received from video equipment.

Set when analog component signals are received from video equipment.

RGB

Component

Set when digital PC RGB signals are received from the computer.

Set when digital PC component signals are received from the computer.

Set when digital video RGB signals are received from video equipment.

Set when digital video component signals are received from video equipment.

Set when analog RGB signals are received.

Set when analog component signals are received.

D. PC RGB

D. PC Comp.

D. Video RGB

D. Video Comp.

A. RGB

A. Comp.

Selecting the Signal Type

Select “Signal Type” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Note

For INPUT 1 and INPUT 2

For INPUT 5

For INPUT 1 and INPUT 2

Selecting the Signal Type

This function allows you to select the input signal type RGB or Component for INPUT 1 and 2, or Digital PC RGB, Digital PC Component, Digital Video RGB, Digital Video Component, Analog RGB or Analog Component for INPUT 5.

• The input signal type can also be switched by pressing . This switching at this time is only able to be performed for switching

the of the above table.

RGB/COMP. button

Page 68

Setting the Video System

Select “Video System” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Note

• The video signal can only be set in INPUT 3 or INPUT 4 mode.

• In “Auto”, images are displayed in PAL even if PAL-N or PAL-M input signals are received.

The video input system mode is preset to “Auto”; however, a clear picture from the con- nected audio-visual equipment may not be received, depending on the video signal difference. In that case, switch the video signal.

When connected to PAL video equipment. When connected to SECAM video

equipment. When reproducing NTSC signals in

PAL video equipment. When connected to NTSC video equipment.

PA L SECAM

NTSC4.43

NTSC3.58

* If the input signal has interference, the screen will be displayed with the interference.

Selecting a Background Image

Select “Background” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Selected Item

Blue

None

Description

Blue screen

Black screen

Setting a Background Image

This function allows you to select the image displayed when no signal is being sent to the projector.

-66

Page 69

Easy to Use Functions

-67

Selecting the Economy Mode

These functions allow you to reduce the power consumption of the projector.

Setting the Power Save

Select “ Power Save” in “Economy Mode” under the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Note

• Although noise is reduced when “Power Save” is set to “ON”, brightness decreases by 20%.

• “Power Save” mode is factory preset to “OFF”.

• “Power Save” is switched on and off by pressing

RS-232C Off Function

This projector consumes power when using a computer connected to the RS-232C terminal. When not using these terminals, “RS-232C Port” can be set to “OFF” to reduce standby power consumption.

Select

“RS-232C Port”

in “Economy

Mode” under the “Options” menu

on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Note

• Set “RS-232C Port” to “ON” when using the SharpVision Manager Software.

• “RS-232C Port” is switched on and off by pressing

Brightness

80%

100%

Status

ON (Low power mode)

OFF (Standard mode)

Power

consumption

220 W

270 W

OFF

RS-232C connection is set to “ON”. The RS-232C is operating at all times (to accept communications).

RS-232C connection is set to “OFF”. RS-232C does not operate when the power supply is in standby.

Page 70

Selecting the Economy Mode

Selecting the Transmission Speed (RS-232C)

This menu allows you to adjust the transmission speed of the RS-232C connection by selecting the baud rate.

-68

Selecting the Transmission Speed (RS-232C)

Select “RS-232C” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Note

• Make sure that both the projector and computer are set for the same baud rate. Refer to the computer’s operation manual for instructions for setting the computer’s baud rate.

Automatic Power Off Function

When no input signal is detected for more than 15 minutes, the projector will automatically turn off if set to “ON”. The Auto Power Off function will be disabled when it is set to “OFF”.

Select “Auto Power Off” in “Economy Mode” under the “Options”

menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Note

• When the Auto Power Off function is set to “ON”, 5 minutes before the power turns off, the message “Power OFF in X min.” will appear on the screen to indicate the remaining minutes.

• “Auto Power Off” is switched on and off by pressing

Page 71

Easy to Use Functions

-69

Reversing/Inverting Projected Images

This projector is equipped with a reverse/invert image function that allows you to reverse or invert the projected image for various applications.

Setting the Projection Mode

Select “PRJ Mode” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.

Selected Item

Front

Ceiling + Front

Rear

Ceiling + Rear

Description

Normal image

Inverted image

Reversed image

Reversed and inverted image

Front Ceiling+Front Rear Ceiling+Rear

Note

• This function is used for the reversed image and ceiling-mount setups. See page 30 for these setups.

Page 72

This function can be used to display all the adjusted settings as a list on the screen.

Displaying the Adjustment Settings

Overview of All Menu Settings

Select the “Status” menu on the menu screen and press . ➝For operating the menu screen, see

pages 40 to 43.

-70

Page 73

Appendix

Page 74

-72

Cleaning the lens

■ Use a commercially available blower or lens cleaning paper (for glasses and camera lenses) for cleaning the lens. Do not use any liquid type cleaning agents, as they may wear off the coating film on the surface of the lens.

■ As the surface of the lens can easily get damaged, be sure not to scrape or hit the lens.

Cleaning the exhaust and intake vents

■ Use a vacuum cleaner to clean dust from the exhaust vent and the intake vent.

Maintenance

Cleaning the projector

■ Be sure to unplug the power cord before cleaning the projector.

■ The cabinet as well as the operation panel is made of plastic. Avoid using benzene or thinner, as these can damage the finish on the cabinet.

■ Do not use volatile agents such as insecticides on the projector. Do not attach rubber or plastic items on the projector for long time.

The effects of some of the agents in the plastic

may cause damage to the quality or finish of the projector.

■ Wipe off dirt gently with a soft flannel cloth.

■ When the dirt is hard to remove, soak a cloth in a

neutral detergent diluted with water, wring the cloth well and then wipe the projector. Strong cleaning detergents may discolor, warp or damage the coating on the projector. Make sure to test on a small, inconspicuous area on the projector before using.

Wax

Thinner

Neutral detergent diluted with water

Neutral detergent

Cleaning

Paper

Page 75

Appendix

-73

Cleaning the Ventilative Holes

Power (OFF) button

Cleaner hose

Ventilative holes

• This projector is equipped with

ventilative holes to ensure the optimal operating condition of the projector.

• Periodically clean the ventilative hole

by vacuuming it off with a vacuum cleaner.

• The ventilative holes should be

cleaned every 100 hours of use. Clean the ventilative holes more often when the projector is used in a dirty or smoky location.

Cleaning the Ventilative Holes

1 Press on the projector or

on the remote control to turn off the power.

• Wait until the cooling fan stops.

2 Disconnect the Power Cord.

3 Clean the dust off by putting

the cleaner hose on the intake ventilative holes.

Side and Rear view Bottom view

Page 76

-74

Maintenance Indicators

■ The warning lights on the projector indicate problems inside the projector.

■ If a problem occurs, either the temperature warning indicator or the lamp replacement indicator will

illuminate red, and the power will turn off. After the power has been turned off, follow the procedures given below.

About the temperature warning indicator

If the temperature inside the projector increases, due to blockage of the air vents, or the setting location, “

” will blink in the lower left corner of the picture. If the temperature keeps on rising, the lamp will turn off and the temperature warning indicator will blink, the cooling fan will run for further 90 seconds, then the power will be shut off. After “

” appears, be sure to perform the following measures.

About the lamp replacement indicator

■ When the lamp exceeds 1,900 cumulative hours of use, “

” will be displayed on the screen in yellow. When the cumulative hours of use reach 2,000, “ ” will change to red, the lamp will automatically turn off and then the projector as well. At this time, the LAMP REPLACEMENT indicator will illuminate in red.

■ If you try to turn on the projector a fourth time without replacing the lamp, the projector will not turn on.

Maintenance indicator Condition Problem Possible Solution

Temperature

warning

indicator

Normal

Abnormal

Off

Red on/ Power off

The internal temperature is abnormally high.

Abnormal

• Blocked air intake

• Relocate the projector to an area

with proper ventilation.

• Cooling fan breakdown

• Internal circuit failure

• Clogged air intake

• Take the projector to your nearest

Authorized SharpVision Service Center or Dealer for repair.

• Clean the ventilative holes according to the procedure on page 73.

Lamp

replacement

indicator

Red on/ Power off

The lamp does not illuminate.

• Burnt-out lamp

• Lamp circuit failure

• Carefully replace the lamp. (See

page 77)

• Take the projector to your nearest Authorized SharpVision Service Center or Dealer for repair.

• Please exercise care when replacing the lamp.

Blue on

Blue

blinks

when the

lamp is

active.

Power

indicator

The power indicator blinks in red when the projector is on.

• The exhaust vent cover is open.

• Securely install the cover.

• If the power indicator blinks even

when the exhaust vent cover is securely installed, contact your nearest Authorized SharpVision Service Center or Dealer for advice.

Blue on/ Red on

Red blinks

Temperature warning indicator

Lamp replacement indicator

Power indicator

Red blinks

Lamp replacement time.

• The lamp usage time has exceeded 1,900 hours.

Page 77

Appendix

-75

Info

• If the temperature warning indicator illuminates, and the power turns off, follow the above possible solutions and then wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 5 minutes.)

• If the power is turned off and then turned on again, as during a brief test, the lamp replacement indicator may be triggered, preventing the power from going on. Should this occur, take the power cord out of the wall outlet and plug it back in again.

• If you want to clean the air vents during projector operation, be sure to first press

. Make sure the power

has turned off and the cooling fan has stopped, then clean the vents.

• Do not unplug the power cord after the power has been turned off and while the cooling fan is running. The cooling fan runs for about 90 seconds.

Page 78

-76

Lamp

■ It is recommended that the lamp (sold separately) be replaced after approximately 1,900 cumulative

hours of use or when you notice a significant deterioration in the picture and color quality. The lamp usage time can be checked with “Lamp Timer” in the “Options” menu on the menu screen.

■ For lamp replacement, please consult your nearest Authorized SharpVision Service Center or Dealer.

■ The actual lamp service life may be less than 2,000 hours depending on the environment in which

the projector is used.

IMPORTANT NOTE TO U.S. CUSTOMERS:

The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through an Authorized SharpVision Service Center or Dealer. For the name of the nearest Authorized SharpVision Service Center or Dealer, please call toll-free: 1-877-DTV-SHARP (1-877-388-7427).

U.S.A. ONLY

Caution Concerning the Lamp

■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp

failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking.

■ When the lamp replacement indicator and on-screen display icon are illuminated or flash, it is rec-

ommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.

■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the

lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult with a doctor as soon as possible.

■ Should the lamp break, there is also a possibility that glass particles may spread inside of the

projector. In such a case, it is recommended you contact your nearest Authorized SharpVision Service Center or Dealer to remove the damaged lamp and assure safe operation.

Replacing the Lamp

Caution

• Do not remove the lamp unit immediately after operation of the projector. The lamp will be hot and touching it can lead to burn or injury.

• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit.

■ If the new lamp does not light after replacement, take your projector to the nearest Authorized

SharpVision Service Center or Dealer for repair. Purchase a replacement lamp unit of type BQCXVZ100001 from your nearest Authorized SharpVision Service Center or Dealer. Then carefully change the lamp by following the instructions described in this section. If you wish, you may have the lamp replaced at your nearest Authorized SharpVision Service Center or Dealer.

Regarding the Lamp

Page 79

Appendix

-77

Lamp unit

BQC-XVZ100001

Removing and Installing the Lamp Unit

Info

• Be sure to remove the lamp unit by the handle. Be sure not to touch the glass surface of the lamp unit or the inside of the projector.

• To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below.

• Do not loosen other screws except for the lamp unit cover and lamp unit. (Only the silver screws are loosened).

• Please refer to the installation manual included with the lamp unit.

1 Press on the projector or

on the remote control to turn off the power.

• Wait until the cooling fan stops.

Warning!

• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burn or injury.

2 Disconnect the power cord.

• Unplug the power cord from the AC socket.

• Leave the lamp until it has fully cooled down (about 1 hour).

3 Remove the lamp unit cover.

• Loosen the user service screws that secure the lamp unit cover. Then open the cover in the direction of the arrow.

User service screws

Page 80

-78

User service screws

4 Remove the lamp unit.

• Loosen the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow.

5 Insert the new lamp unit.

• Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws.

6 Attach the lamp unit cover.

• Close the lamp unit cover in the direction of the arrow (to the close mark) on the side of the projector. Then tighten the user service screws.

Info

• If the lamp unit and lamp cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector.

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.

1 Connect the power cord.

• Plug the power cord into the AC socket of the projector.

2 Reset the lamp timer.

•

While holding down , " and | on

the projector, press

on the projector.

• “LAMP 0000H” is displayed, indicat- ing that the lamp timer is reset.

Info

• Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode.

-78

Regarding the Lamp

Page 81

Appendix

-79

Connecting Pin Assignments

RS-232C Port: 9-pin D-sub male connector of the DIN-D-sub RS-232C cable

Pin No. Signal Name I/O Reference

1 Not connected 2 RD Receive Data Input Connected to internal circuit 3 SD Send Data Output Connected to internal circuit 4 Reserved Connected to internal circuit 5 SG Signal Ground Connected to internal circuit 6 Reserved Connected to internal circuit 7 Reserved Connected to internal circuit 8 Reserved Connected to internal circuit 9 Not connected

DVI-I (INPUT 5 / DIGITAL INPUT) port : 29 pin connector

• DVI Digital INPUT

Pin No. Signal Pin No. Signal

1 T.M.D.S data 2– 16 Hot plug detection 2 T.M.D.S data 2+ 17 T.M.D.S data 0– 3 T.M.D.S data 2 shield 18 T.M.D.S data 0+ 4 Not connected 19 T.M.D.S data 0 shield 5 Not connected 20 Not connected 6 DDC clock 21 Not connected 7 DDC data 22 T.M.D.S clock shield 8 Not connected 23 T.M.D.S clock+

9 T.M.D.S data 1– 24 T.M.D.S clock– 10 T.M.D.S data 1+ C1 Not connected 11 T.M.D.S data 1 shield C2 Not connected 12 Not connected C3 Not connected 13 Not connected C4 Not connected 14 +5V power C5 Ground 15 Ground

• DVI Analog RGB Input

Pin No. Signal Pin No. Signal

1 Not connected 16 Hot plug detection 2 Not connected 17 Not connected 3 Not connected 18 Not connected 4 Not connected 19 Not connected 5 Not connected 20 Not connected 6 DDC clock 21 Not connected 7 DDC data 22 Not connected 8 Vertical sync 23 Not connected

9 Not connected 24 Not connected 10 Not connected C1 Analog input Red 11 Not connected C2 Analog input Green 12 Not connected C3 Analog input Blue 13 Not connected C4 Horizontal sync 14 +5V power C5 Ground 15 Ground

• DVI Analog Component Input

Pin No. Signal Pin No. Signal

1 Not connected 16 Not connected 2 Not connected 17 Not connected 3 Not connected 18 Not connected 4 Not connected 19 Not connected 5 Not connected 20 Not connected 6 Not connected 21 Not connected 7 Not connected 22 Not connected 8 Not connected 23 Not connected

9 Not connected 24 Not connected 10 Not connected C1 Analog input Pr/Cr 11 Not connected C2 Analog input Y 12 Not connected C3 Analog input Pb/Cb 13 Not connected C4 Not connected 14 Not connected C5 Ground 15 Ground

8 7

•••••

2 1

•••••••••

•••

4 3 2 1

8 7 6

Page 82

-80

PC control

A computer can be used to control the projector by connecting an RS-232C cable (null modem, cross type, commercially available) to the projector. (See page 23 for connection.)

Communication conditions

Set the serial port settings of the computer to match that of the table. Signal format: Conforms to RS-232C standard. Baud rate*: 9,600 bps / 38,400bps / 115,200bps Data length: 8 bits Parity bit: None Stop bit: 1 bit Flow control: None *Use the same settings for the projector and computer.

Basic format

Commands from the computer are sent in the following order: command, parameter, and return code. After the projector processes the command from the computer, it sends a response code to the computer.

Info

• When more than one code is being sent, send each command only after the response code for the previous command from the projector is verified.

• In the case of transmitting commands during standby, it takes a maximum of 30 seconds until the response code is received.

• When the power is turned on during standby with the “POWER ON” command, wait for at least 30 seconds after the power has been turned on, and then transmit the next command.

Note

• When using the computer control function of the projector, the projector’s operating status cannot be read

by the computer. Therefore, confirm the status by transmitting the display commands for each adjustment menu and checking the status with the on-screen display. If the projector receives a command other than a menu display command, it will execute the command without displaying the on-screen display.

Commands

Example:

• When “BRIGHT” of INPUT 1 image adjustment is set to –10.

Return code (0DH)

C1 C2 C3 C4 P1 P2 P3 P4

Response code format

Normal response

Problem response (communication error or incorrect command)

O K

E R R

Command 4-digit Parameter 4-digit

Command format

Return code (0DH)

Return code (

0DH)

(RS-232C) Specifications and Command Settings

→

←

RABR 1 0_ –

ProjectorComputer

Page 83

Appendix

-81

CONTROL CONTENTS

COMMAND

PARAMETER

RETURN CONTROL CONTENTS

COMMAND

PARAMETER

RETURN

P P K V I I I I I I

A R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R

R R R R R R R R R R R R R R R R R V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V G G G G G G G G G G G G G G G G

O O E S R R V V R C D A A A A B B B B B B B B A A A A C C C C A A A A A A A A A A A A A A A A B B B B B B B B B B B B B B B B C C C C C C C C

C C C C C C C C A A A B B B C C C B B B B B B B B B B B B B B B B A A A A A A A A A A A A A A A A B B B A A A M M M M M M M M M M M M M M M M

W W

Y I G G E E G H J S S S S S S S S S S S S S S S S S S S S P B C T S C R

R W W

W W P P P P P P

I I I I I I I I

I P B C

T S C R R W W P P P P P P P B C

T S C R R W W P P P P P P

I R R R R R R R R R R R R V V V V

R R S Z B B D D B K S R R R R R R R R V V V V V V V V R R R R I R O I H T E E E E S S S S S S I R O I H T E E E E S S S S S S I R O I H T E E

E E S S S S S S P P P P P P P P P I R O I H T E E E E S S S S S S I R O I H T E E E E S S S S S S P P P P P P A A A A A A B B B B B B B B B B

_ _ * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ * * * * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

_ _ * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ * * * * * * _ _ _ _ _ _ _ _ _ _ * * * * * * _ _ _ _ _ _ _ _ _ _ * * * * * * _ _

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ * * * * * * _ _ _ _ _ _ _ _ _ _ * * * * * * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

_ _ * * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ * * * * * * _ _ _ _ _ _ _ _ _ _ * * * * * * _ _ _ _ _ _ _ _ _ _ * * * * * * _ _

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ * * * * * * _ _ _ _ _ _ _ _ _ _ * * * * * * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR

1 0 * * 1 2 2 1 3 0 1 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 * * * * * * 0 1 0 1 0 1 2 3 4 5 * * * * * * 0 1 0 1 0 1 2 3 4 5 * * * * * * 0 1

0 1 0 1 2 3 4 5 0 1 2 0 1 2 0 1 2 * * * * * * 0 1 0 1 0 1 2 3 4 5 * * * * * * 0 1 0 1 0 1 2 3 4 5 0 1 2 0 1 2 0 1 2 3 4 5 0 1 2 3 4 5 0 1 2 3

POWER ON POWER OFF KEYSTONE (–127 – +127) V-SIZE (–10 – +10) INPUT 1 INPUT 2 INPUT 3 INPUT 4 INPUT 5 INPUT CHECK AUTO SYNC START INPUT 1 RESIZE : SIDE BAR/DOT BY DOT/NORMAL INPUT 1 RESIZE : SMART STRETCH INPUT 1 RESIZE : CINEMA ZOOM INPUT 1 RESIZE : STRETCH INPUT 2 RESIZE : SIDE BAR/DOT BY DOT/NORMAL INPUT 2 RESIZE : SMART STRETCH INPUT 2 RESIZE : CINEMA ZOOM INPUT 2 RESIZE : STRETCH INPUT 3 RESIZE : SIDE BAR INPUT 3 RESIZE : SMART STRETCH INPUT 3 RESIZE : CINEMA ZOOM INPUT 3 RESIZE : STRETCH INPUT 4 RESIZE : SIDE BAR INPUT 4 RESIZE : SMART STRETCH INPUT 4 RESIZE : CINEMA ZOOM INPUT 4 RESIZE : STRETCH INPUT 5 RESIZE : SIDE BAR/DOT BY DOT/NORMAL INPUT 5 RESIZE : SMART STRETCH INPUT 5 RESIZE : CINEMA ZOOM INPUT 5 RESIZE : STRETCH INPUT 1 CONTRAST (–30 – +30) INPUT 1 BRIGHT (–30 – +30) INPUT 1 COLOR (–30 – +30) INPUT 1 TINT (–30 – +30) INPUT 1 SHARP (–30 – +30) INPUT 1 CLR TEMP (55 – 115) INPUT 1 DISPLAY INPUT 1 ADJUSTMENT RESET INPUT 1 WHITE ENPHASIS : OFF INPUT 1 WHITE ENPHASIS : ON INPUT 1 PICTURE SETTING : INPUT 1 MEMORY INPUT 1 PICTURE SETTING : MEMORY 1 INPUT 1 PICTURE SETTING : MEMORY 2 INPUT 1 PICTURE SETTING : MEMORY 3 INPUT 1 PICTURE SETTING : MEMORY 4 INPUT 1 PICTURE SETTING : MEMORY 5 INPUT 2 CONTRAST (–30 – +30) INPUT 2 BRIGHT (–30 – +30) INPUT 2 COLOR (–30 – +30) INPUT 2 TINT (–30 – +30) INPUT 2 SHARP (–30 – +30) INPUT 2 CLR TEMP (55 – 115) INPUT 2 DISPLAY INPUT 2 ADJUSTMENT RESET INPUT 2 WHITE ENPHASIS : OFF INPUT 2 WHITE ENPHASIS : ON INPUT 2 PICTURE SETTING : INPUT 2 MEMORY INPUT 2 PICTURE SETTING : MEMORY 1 INPUT 2 PICTURE SETTING : MEMORY 2 INPUT 2 PICTURE SETTING : MEMORY 3 INPUT 2 PICTURE SETTING : MEMORY 4 INPUT 2 PICTURE SETTING : MEMORY 5 INPUT 5 CONTRAST (–30 – +30) INPUT 5 BRIGHT (–30 – +30) INPUT 5 COLOR (–30 – +30) INPUT 5 TINT (–30 – +30) INPUT 5 SHARP (–30 – +30) INPUT 5 CLR TEMP (55 – 115) INPUT 5 DISPLAY INPUT 5 ADJUSTMENT RESET

PICTURE

BUTTONS & REMOTE CONTROL KEY

INPUT 5 WHITE ENPHASIS : OFF INPUT 5 WHITE ENPHASIS : ON INPUT 5 PICTURE SETTING : INPUT 5 MEMORY INPUT 5 PICTURE SETTING : MEMORY 1 INPUT 5 PICTURE SETTING : MEMORY 2 INPUT 5 PICTURE SETTING : MEMORY 3 INPUT 5 PICTURE SETTING : MEMORY 4 INPUT 5 PICTURE SETTING : MEMORY 5 INPUT 1 2D PROGRESSIVE INPUT 1 3D PROGRESSIVE INPUT 1 Film MODE INPUT 2 2D PROGRESSIVE INPUT 2 3D PROGRESSIVE INPUT 2 Film MODE INPUT 5 2D PROGRESSIVE INPUT 5 3D PROGRESSIVE INPUT 5 Film MODE INPUT 3 CONTRAST (–30 – +30) INPUT 3 BRIGHT (–30 – +30) INPUT 3 COLOR (–30 – +30) INPUT 3 TINT (–30 – +30) INPUT 3 SHARP (–30 – +30) INPUT 3 CLR TEMP (55 – 115) INPUT 3 DISPLAY INPUT 3 ADJUSTMENT RESET INPUT 3 WHITE ENPHASIS : OFF INPUT 3 WHITE ENPHASIS : ON INPUT 3 PICTURE SETTING : INPUT 3 MEMORY INPUT 3 PICTURE SETTING : MEMORY 1 INPUT 3 PICTURE SETTING : MEMORY 2 INPUT 3 PICTURE SETTING : MEMORY 3 INPUT 3 PICTURE SETTING : MEMORY 4 INPUT 3 PICTURE SETTING : MEMORY 5 INPUT 4 CONTRAST (–30 – +30) INPUT 4 BRIGHT (–30 – +30) INPUT 4 COLOR (–30 – +30) INPUT 4 TINT (–30 – +30) INPUT 4 SHARP (–30 – +30) INPUT 4 CLR TEMP (55 – 115) INPUT 4 DISPLAY INPUT 4 ADJUSTMENT RESET INPUT 4 WHITE ENPHASIS : OFF INPUT 4 WHITE ENPHASIS : ON INPUT 4 PICTURE SETTING : INPUT 4 MEMORY INPUT 4 PICTURE SETTING : MEMORY 1 INPUT 4 PICTURE SETTING : MEMORY 2 INPUT 4 PICTURE SETTING : MEMORY 3 INPUT 4 PICTURE SETTING : MEMORY 4 INPUT 4 PICTURE SETTING : MEMORY 5 INPUT 3 2D PROGRESSIVE INPUT 3 3D PROGRESSIVE INPUT 3 Film MODE INPUT 4 2D PROGRESSIVE INPUT 4 3D PROGRESSIVE INPUT 4 Film MODE INPUT 1 GAMMA POSITION : STANDARD INPUT 1 GAMMA POSITION : BLACK DETAIL INPUT 1 GAMMA POSITION : BRIGHTEN INPUT 1 GAMMA POSITION : CUSTOM 1 INPUT 1 GAMMA POSITION : CUSTOM 2 INPUT 1 GAMMA POSITION : SVM GAMMA INPUT 2 GAMMA POSITION : STANDARD INPUT 2 GAMMA POSITION : BLACK DETAIL INPUT 2 GAMMA POSITION : BRIGHTEN INPUT 2 GAMMA POSITION : CUSTOM 1 INPUT 2 GAMMA POSITION : CUSTOM 2 INPUT 2 GAMMA POSITION : SVM GAMMA INPUT 3 GAMMA POSITION : STANDARD INPUT 3 GAMMA POSITION : BLACK DETAIL INPUT 3 GAMMA POSITION : BRIGHTEN INPUT 3 GAMMA POSITION : CUSTOM 1

PICTURE

GAMMA

Page 84

-82

Note

• If an underbar (_) appears in the parameter column, enter a space. If an asterisk (*) appears, enter a value in the range indicated in brackets under CONTROL CONTENTS.

• *

FINE SYNC can only be set in the displayed RGB mode.

The return value of “TLTT

___

1” becomes “0” when the projector is in the following states:

• Power is in the standby mode

• Cooling fan is operating after the power has been turned off

CONTROL CONTENTS

COMMAND

PARAMETER

RETURN CONTROL CONTENTS

COMMAND

PARAMETER

RETURN

G G G G G G G G G G G G G G G G G G G G G G G G

C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C I I I I

I M M T T A A A

I S S T T 3 3 3 3

I M M M M M M M

I A A T

I M M M M M M M M M M M

M M M M M M M M M M M M M M M M M M M M M M M M S S S S S S S S S S S S S S S S S S S S M M M M M M M M M M M N N A A

A A E E

F A A A M M T T H H D D D D M M M A A B B E E E E E E E C C C C C C M M P P L M M M M E E E E E E E E E E E

V V V V V V V V R R R R R R E E E G G G O O O R R R R R R R R R V V V V V V V V R R R R T T T T T T S S S R R C P H V

R R M M R R D D D A A S S M M N N N N D D D S S S S S S S S S S S S S S S S S B B O O

T P P P P

B B A A A A A A C C C C C C R G B R G B R G B E A A A A B B B B B B B B A A A A C C C C G G G G G G L C H E E L H P P

E E S L Q Q J J J S S H Z D D R R R R I I I I I I I Y Y Y Y Y Y Y I I I I I I G

G W W

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ * _ * _

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

_ _ _ _ _ _ _ _ _ _ _ _ _ _ * * * * * * * * * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ * * * _ _ * * * *

_ _ _ _ _ _ _ _ _ _ _ * * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

_ _ _ _ _ _ _ _ _ _ _ _ _ _ * * * * * * * * * _ _ 1 1 1 _ 1 1 1 _ 1 1 1 _ 1 1 1 _ 1 1 1 _ _ _ _ _ _ * * * _ _ * * * *

_ _ _ _ _ _ _ _ _ _ _ * * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 1 1

OK OR ERR OK OR ERR OK OR ERR OK OR ERR kHz (***. *OR_) Hz (***. *OR_) OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR 0–9999 (INTEGER) OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR

4 5 0 1 2 3 4 5 0 1 2 3 4 5 * * * * * * * * * 1 0 1 2 3 0 1 2 3 0 1 2 3 0 1 2 3 0 1 2 3 1 2 3 4 5 6 * * * 1 2 * * * *

0 1 * * 1 2 1 2 0 1 0 * * 1 0 0 1 2 3 1 2 0 1 2 1 2 1 2 3 4 5 6 7 1 2 3 4 5 6 1 2 0 1 1 0 1 2 3 1 2 3 4 5 6 7 8 9 0 1

INPUT 3 GAMMA POSITION : CUSTOM 2 INPUT 3 GAMMA POSITION : SVM GAMMA INPUT 4 GAMMA POSITION : STANDARD INPUT 4 GAMMA POSITION : BLACK DETAIL INPUT 4 GAMMA POSITION : BRIGHTEN INPUT 4 GAMMA POSITION : CUSTOM 1 INPUT 4 GAMMA POSITION : CUSTOM 2 INPUT 4 GAMMA POSITION : SVM GAMMA INPUT 5 GAMMA POSITION : STANDARD INPUT 5 GAMMA POSITION : BLACK DETAIL INPUT 5 GAMMA POSITION : BRIGHTEN INPUT 5 GAMMA POSITION : CUSTOM 1 INPUT 5 GAMMA POSITION : CUSTOM 2 INPUT 5 GAMMA POSITION : SVM GAMMA R-GAMMA (–30 – +30) G-GAMMA (–30 – +30) B-GAMMA (–30 – +30) R-GAIN (–30 – +30) G-GAIN (–30 – +30) B-GAIN (–30 – +30) R-OFFSET (–30 – +30) G-OFFSET (–30 – +30) B-OFFSET (–30 – +30) GAMMA RESET INPUT 1 COLOR SELECTED : STANDARD INPUT 1 COLOR SELECTED : CUSTOM 1 INPUT 1 COLOR SELECTED : CUSTOM 2 INPUT 1 COLOR SELECTED : CUSTOM 3 INPUT 2 COLOR SELECTED : STANDARD INPUT 2 COLOR SELECTED : CUSTOM 1 INPUT 2 COLOR SELECTED : CUSTOM 2 INPUT 2 COLOR SELECTED : CUSTOM 3 INPUT 3 COLOR SELECTED : STANDARD INPUT 3 COLOR SELECTED : CUSTOM 1 INPUT 3 COLOR SELECTED : CUSTOM 2 INPUT 3 COLOR SELECTED : CUSTOM 3 INPUT 4 COLOR SELECTED : STANDARD INPUT 4 COLOR SELECTED : CUSTOM 1 INPUT 4 COLOR SELECTED : CUSTOM 2 INPUT 4 COLOR SELECTED : CUSTOM 3 INPUT 5 COLOR SELECTED : STANDARD INPUT 5 COLOR SELECTED : CUSTOM 1 INPUT 5 COLOR SELECTED : CUSTOM 2 INPUT 5 COLOR SELECTED : CUSTOM 3 TARGET : RED TARGET : YELLOW TARGET : GREEN TARGET : CYAN TARGET : BLUE TARGET : MAGENTA LIGHTNESS (–30 – +30) CHROMA (–30 – +30) HUE (–30 – +30) RESET (THIS COLOR) RESET (ALL COLORS) CLOCK (–150 – +150) PHASE (–60 – +60) H-POSITION (–150 – +150) V-POSITION (–60 – +60)

RGB INPUT DISPLAY RGB ADJUSTMENT RESET SAVE SETTING (1 – 7) SELECT SETTING (1 – 7) RGB HORIZONTAL FREQUENCY CHECK RGB VERTICAL FREQUENCY CHECK AUTO SYNC : ON (NOTMAL) AUTO SYNC : ON (HIGH SPEED) AUTO SYNC : OFF AUTO SYNC DISPLAY ON AUTO SYNC DISPLAY OFF DIGITAL SHIFT (–30 – +30) SUBTITLE (–30 – +30) POWER SAVE MODE : ON POWER SAVE MODE : OFF 3D DNR : OFF 3D DNR : LEVEL 1 3D DNR : LEVEL 2 3D DNR : LEVEL 3 OSD DISPLAY : NORMAL OSD DISPLAY : LEVEL A OSD DISPLAY : LEBEL B INPUT 1 SIGNAL TYPE : RGB INPUT 1 SIGNAL TYPE : COMPONENT INPUT 2 SIGNAL TYPE : RGB INPUT 2 SIGNAL TYPE : COMPONENT VIDEO SYSTEM SELECTION : AUTO VIDEO SYSTEM SELECTION : PAL VIDEO SYSTEM SELECTION : SECAM VIDEO SYSTEM SELECTION : NTSC4.43 VIDEO SYSTEM SELECTION : NTSC3.58 VIDEO SYSTEM SELECTION : PAL-M VIDEO SYSTEM SELECTION : PAL-N INPUT 5 SIGNAL TYPE : ANALOG RGB INPUT 5 SIGNAL TYPE : ANALOG COMPONENT INPUT 5 SIGNAL TYPE : DIGITAL COMPUTER (RGB) INPUT 5 SIGNAL TYPE : DIGITAL COMPUTER (COMPONENT) INPUT 5 SIGNAL TYPE : DIGITAL VIDEO (RGB) INPUT 5 SIGNAL TYPE : DIGITAL VIDEO (COMPONENT) BACKGROUND SELECTION : BLUE BACKGROUND SELECTION : NONE AUTO POWER OFF : NO USE AUTO POWER OFF : USE LAMP USAGE TIME PROJECTION MODE : FRONT PROJECTION MODE : CEILING + FRONT PROJECTION MODE : REAR PROJECTION MODE : CEILING + REAR LANGUAGE SELECTION : ENGLISH LANGUAGE SELECTION : DEUTSCH LANGUAGE SELECTION : ESPAÑOL LANGUAGE SELECTION : NEDERLANDS LANGUAGE SELECTION : FRANÇAIS LANGUAGE SELECTION : ITALIANO LANGUAGE SELECTION : SVENSKA LANGUAGE SELECTION : LANGUAGE SELECTION : PORTUGUÊS LANGUAGE SELECTION : LANGUAGE SELECTION :

GAMMA

C.M.S.

FINE SYNC*

Options

LANGUAGE

(RS-232C) Specifications and Command Settings

FINE SYNC*

Page 85

Appendix

-83

CONTROL

ITEM

SYSTEM CODE

OFF

∂

ENTER

UNDO

RGB/COMP.

C5 C6

C10 C11

C12

C13

C14

C15

DATA CODE

JUDGEMENT

CODE

JUDGEMENT

CODE

CONTROL

ITEM

SYSTEM CODE

RESIZE

PICTURE SETTING

AUTO SYNC

KEYSTONE

INPUT 1

INPUT 2

INPUT 3

INPUT 4

INPUT 5

C5 C6

C10 C11

C12

C13

C14

C15

DATA CODE

Wired Remote Control Terminal Specifications

Wired remote control function code

LSB MSB

• System codes C1 to C5 are fixed at “10110”.

• Codes C14 and C15 are reverse confirmation bits, with “10” indicating “Front” and “01” indicating “Rear”.

C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14

System Address

D to D Common Data Bit Reverse in D

Function Key Data Bit

Data

Expansion

Data

Deter-

mination

Mask

C15

C11DC20C31C41C50C61C70C80C90C100C110C120C130C141C15

C11DC20C31C41C50C60C71C81C91C101C111C121C131C140C15

“0”“1”“0”

“0”“0”“0”“1”

26.4 µs

DDDDDD

DDDDDDD

67.5 ms 67.5 ms

10110********10

C1 System Code C5 C6 Data Code C13 C14 C15

Specifications of wired remote control input

• ø3.5 mm minijack

• External: GND

• Internal: +3.3V

Function and transmission codes

Sharp remote control signal format

Transmission format: 15-bit format

Wave form of output signal: Output using Pulse Position Modulation

• t = 264 µs • Pulse carrier frequency = 37.917 kHz

• T

0 = 1.05 ms • Duty ratio = 1:1

• T

1 = 2.10 ms

Transmission control code

15 bit Example of Reverse D to D

Page 86

-84

Computer Compatibility Chart

Note

• This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this occur, turn off the LCD display on the notebook computer and output the display data in “CRT only” mode. Details on how to change display modes can be found in your notebook computer’s operation manual.

• When this projector receives 640 × 350 VESA format VGA signals, “640 × 400” appears on the screen.

• When projecting moving image of interlace signals using RGB input, the intended image may not be projected depending on the signal

types. In such cases, use the component, S-video or video input.

• Multiple signal support Horizontal Frequency: 15–81 kHz, Vertical Frequency: 43–100 Hz, Pixel Clock: 12–120 MHz

• Compatible with sync on green and composite sync signals

• SXGA compatible in advanced intelligent compression

• AICS (Advanced Intelligent Compression and Expansion System) resizing technology

The following is a list of modes that conform to VESA. However, this projector supports other signals that are not VESA standards.

Upscale

640 × 350

720 × 350

640 × 400

720 × 400

640 × 480

800 × 600

1,024 × 768

31.5

37.9

27.0

31.5

27.0

31.5

37.9

27.0

31.5

37.9

26.2

31.5

36.8

37.9

37.5

43.3

47.9

53.0

31.4

35.1

37.9

44.5

48.1

46.9

53.7

56.8

64.0

70 85 60 70 60 70 85 60 70 85

60 70 72 75 85 90

100

50 56 60 70 72 75 85 90

100

✔

XGA

SVGA

VGA

35.5

40.3

48.4

56.5

60.0

68.7

73.5

77.2

80.6

43 50 60 70 75 85 90 96

100

Display

PC/ MAC/ WS

Resolution

Horizontal

Frequency

(kHz)

Vertical

Frequency

(Hz)

VESA

Standard

27.0 60

✔

✔ ✔

✔

✔ ✔ ✔

DTV

Computer

Signal

480I

480P

576I 576P 720P 720P 1080I 1080I

Horizontal Frequency (kHz)

15.8

31.5

15.6

31.3

45.0

37.5

33.8

28.1

Vertical Frequency (Hz)

60 60 50 50 60 50 60 50

DVI

Support

✔

✔ ✔

Advanced Intelligent

Compres-

sion

1,152

864

1,152

882

1,280 ×1,024

64.0

64.1

67.5

75.7

54.8

65.9

67.4

64.0

34.9

70 85 60 70 60 72 74 60

✔

SXGA

Display

PC/ MAC/ WS

Resolution

Horizontal Frequency

(kHz)

Vertical

Frequency

(Hz)

VESA

Standard

54.3 60

✔

DVI

Support

✔

✔ ✔

MAC

13”

VGA

640 × 480

49.6 75

MAC

16”

SVGA

832 × 624

Upscale

✔

48.4 60

MAC

19”

XGA

1,024 × 768

68.5 75

MAC

21”

SXGA

1,152

870

Advanced Intelligent

Compres-

sion

(WS)

60.0 60

1,280

960

SGI

(WS)

53.5 50

1,280×1,024

SUN

(WS)

60.9 66

1,152

900

71.9 76

SXGA

DVI Support

✔

✔ ✔ ✔ ✔ ✔

Advanced Intelligent

Compres-

sion

Page 87

Appendix

-85

Troubleshooting

Check Page

• Projector power cord is not plugged into the wall outlet. 16

• Power to the external connected devices is off. –

• The selected input mode is wrong. 33

• Cables incorrectly connected to rear panel of the projector. 17-22

• Remote control batteries have run out. 13

•

External output has not been set when connecting notebook computer.

–

• The cover of the lamp unit is not installed correctly. 78

• The selected “Signal Type” is wrong. 65

•

The video signal format of the video equipment is not set correctly.

• “Bright” is set to minimum position. 44

• Picture adjustments are incorrectly set. 44

(Video Input only)

• Video input system is incorrectly set. 66 (INPUT 1, 2 and 5 only)

• Input signal type is incorrectly set. 65

• Adjust the focus. 26

• The projection distance exceeds the focus range. 28-29

(Computer Input only)

• Perform “Fine Sync” Adjustments (“Clock” Adjustment) 53

• Perform “Fine Sync” Adjustments (“Phase” Adjustment) 53

• Noise will appear depending on the computer. –

• The “DNR” (Digital Noise Reduction) setting is not correct. 63

• If the picture is normal, the sound is due to cabinet shrinkage –

caused by a room temperature changes. This will not affect operation or performance.

• See “Maintenance Indicators”. 74

Problem

Color is faded or poor.

Picture is blurred;

noise appears.

No picture and no sound

or projector does not start.

An unusual sound is

occasionally heard

from the cabinet.

Maintenance

indicator illuminates.

Page 88

-86

CheckProblem Page

Troubleshooting

For SHARP Assistance (U.S.A only)

If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting” section on pages 85 and 86. If this operation manual does not answer your question, please call toll free 1-877-DTV-SHARP (1-877-388-7427) for further assistance. Or, send us an email at lcdsupport@sharpsec.com . Our World Wide Web address is http://www.sharpusa.com/ .

• Change the input signal type setting. 65

• The lamp replacement indicator is blinking in red. Replace the 74

lamp.

• Picture adjustments are incorrectly set. 44

• In the case of transmitting RS-232C commands from a computer 80

during standby, it takes a maximum of 30 seconds for the computer to receive the response code. Set the response code waiting time of the computer to 30 seconds or more.

Picture is green on

INPUT 1 or 2

COMPONENT.

Picture is pink (no green)

on INPUT 1 or 2 RGB.

Picture is dark.

Picture is too bright and

whitish.

A response code cannot

be received when the

projector was attempted

to be controlled using

RS-232C commands

from a computer during

standby.

Page 89

Appendix

-87

Specifications

Projector XV-Z10000 NTSC 3.58/NTSC 4.43/PAL/PAL-M/PAL-N/PAL 60/SECAM DTV480I/DTV480P/DTV720P/DTV1080I DLP chip, RGB optical shutter method Panel size: 0.8" Display method: Single Panel Digital Micromirror Device (DMD™) by Texas Instruments Drive method: Digital Light Processing (DLP™) No. of dots: 921,600 dots (1,280 [H] × 720 [V]) 1–1.35 × zoom lens, F3.8, f = 32.5–44.0 mm 270 W SHP lamp 4-pin Mini DIN connector (INPUT 3) Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated RCA Connector (INPUT 1, 2) Y: 1.0 Vp-p, sync negative, 75 Ω terminated PB: 0.7 Vp-p, 75 Ω terminated PR: 0.7 Vp-p, 75 Ω terminated 520 TV lines (NTSC 3.58 input), 750 TV lines (DTV 720P input) DVI-I terminal: (INPUT 5)/RCA connector: INPUT 1/2 <Digital> Input impedance 50 Ω Input level 250-1000mV <Analog> Input Impedance 75 Ω Input level 0.7Vp-p <Synchronization signal>

• Separate sync / Composite sync Input level TTL level Input impedance 1 K Ω

• Green on sync Input level (Synchronizing input) 0.286Vp-p Input Impedance 75 Ω

RCA Connector: VIDEO (INPUT 4), composite video, 1.0 Vp-p, sync negative, 75 Ω terminated 9-pin D-sub connector (RS-232C Port) 12–120 MHz 43–100 Hz 15–81 kHz AC 100–240 V

3.7 A (When using AC100V)

50/60 Hz 365 W About 0.1 W (When using 100 V) 1,400 BTU/hour 41°F to 95°F (+5°C to +35°C) –4°F to 140°F (–20°C to +60°C) Plastic 38 kHz 18 11/16" × 7" × 15 49/50" (475 (W) × 178 (H) × 406 (D) mm) (main body only) 18 11/16" × 7" × 19 1/2" (475 (W) × 178 (H) × 496 (D) mm) (including terminal cover)

20.7 lbs. (9.4 kg)

Remote control, Two AA size batteries, Power cord (11'10", 3.6 m), Terminal cover, Lens cap (attached), SharpVision Manager Software CD-ROM, Projector operation manual, SharpVision Manager operation manual Lamp unit (Lamp/cage module) (BQC-XVZ100001), Remote control (RRMCGA128WJSA), AA size batteries , Power cord (CACCDA010DE01),

Terminal cover (CCOVA1985CE02)

Lens cap (PCAPH1056CESA),

SharpVision Manager

Software CD-ROM (UDSKAA028WJN1),

Projector operation manual (TINS-A440WJZZA),

SharpVision Manager operation manual

(TINS-A452WJZZ)

Product type

Model

Video system

Display method

DLP panel

Lens

Projection lamp

S-video input signal

Component input signal

Horizontal resolution

RGB input signal

Video input signal

Computer control signal

Pixel clock

Vertical frequency

Horizontal frequency

Rated voltage

Input current

Rated frequency

Power consumption (normal)

Power consumption(standby)

Heat dissipation

Operating temperature

Storage temperature

Cabinet

I/R carrier frequency

Dimensions (approx.)

Weight (approx.)

Supplied accessories

Replacement parts

This SHARP projector uses a DMD Chip. This very sophisticated panel contains 921,600 pixels. As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to.

This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit. If you have any questions about this matter, please call toll free 1-877-DTV-SHARP (1-877-388-7427).

U.S.A ONLY

Specifications are subject to change without notice.

Page 90

-88

Dimensions

(406)

7 (178)

18 11/16 (475)

Side View Side ViewTop View

Rear View

Front View

Bottom View

Units: inches (mm)

Page 91

Appendix

-89

Glossary

Advanced intelligent compression

High quality resizing of lower and higher resolution images to fit the projector’s native resolution.

Aspect Ratio

Width and height ratio of an image. The normal aspect ratio of a computer and video image is 4:3. There are also wide images with an aspect ratio of 16:9 and 21:9.

Auto Sync

Optimizes projected computer images by automatically adjusting certain characteristics.

Background

Initial setting image projected when no signal is being output.

Clock

Clock adjustment is used to adjust vertical noise when clock level is incorrect.

CLR Temp (Color temperature)

Function that can be used to adjust the color temperature to suit the type of image input to the projector. Decrease the color temperature to create warmer, reddish images for natural flesh tones, or increase to create cooler, bluish images for a brighter picture.

C.M.S. (Color Management System)

Function allows you individually adjust the display characteristics of six colors (R: Red, Y: Yellow, G: Green, C: Cyan, B: Blue, M: Magenta)

Digital Shift Setting

The image can be moved vertically when the image display mode is set to SMART STRETCH or CINEMA ZOOM during input of video or DTV signals.

Dot by dot

Mode that projects images in their native resolution.

Gamma

Image quality enhancement function that offers a richer image by brightening the darker portions of the image without altering the brightness of the brighter portions.

HDCP

Display digital interface that also supports Analog interfaces.

Keystone correction

Function to digitally correct a distorted image when the projector is set up at an angle, smoothens out jaggies on keystone images and compresses the image not only horizontally but vertically keeping the 4:3 aspect ratio.

Phase

Phase shift is a timing shift between isomorphic signals with the same resolution. When phase level is incorrect, the projected image typically displays horizontal flicker.

Progressive Mode

The progressive display projects a smoother video image. You can select three different modes: 2D Progressive, 3D Progressive and Film Mode.

Resize

Allows you to modify or customize the picture display mode to enhance the input image. You can select six different modes: SIDE BAR, SMART STRETCH, CINEMA ZOOM, STRETCH, DOT BY DOT or NORMAL.

Smart Stretch

Mode that stretches the right and left sides of the 4:3 image horizontally while maintaining the aspect ratio around the center of the image to display it on the WIDE screen.

Stretch

Mode that stretches the 4:3 image horizontally to display it fully on a 16:9 screen.

Page 92

-90

2D Progressive .................................................... 46

3D Progressive .................................................... 46

AC socket ............................................................ 16

Adjusting Computer Images ................................ 53

Adjusting the Lens ............................................... 26

Adjusting the Picture ............................................ 44

Adjustment buttons .............................................. 32

Adjustment feet .................................................... 25

Aspect ratio .......................................................... 59

Auto Power Off .................................................... 68

Auto Sync Adjustment ......................................... 55

AUTO SYNC button ............................................. 55

Auto Sync Disp .................................................... 56

Background .......................................................... 66

Batteries ............................................................... 13

Ceiling-mount setup ............................................. 30

CD-ROM ................................................................ 9

Chroma ................................................................ 51

CINEMA ZOOM ................................................... 59

Clock .................................................................... 53

CLR Temp (Color Temperature) .......................... 44

C.M.S. .................................................................. 50

Color Selected ..................................................... 50

DC 12V OUTPUT terminal .................................. 11

Digital Shift ........................................................... 62

DNR ..................................................................... 63

DOT BY DOT ....................................................... 59

ENTER button ...................................................... 32

Exhaust vent ........................................................ 73

Film Mode ............................................................ 46

Fine Sync ............................................................. 53

Focus ring ............................................................ 26

HIGH CONTRAST/HIGH BRIGHTNESS

MODE button .................................................... 61

Hue ...................................................................... 51

INPUT 1 terminals ............................................... 18

INPUT 1 – 5 modes ............................................. 33

INPUT 2 terminals ............................................... 18

INPUT 3 terminal ................................................. 17

INPUT 4 terminal ................................................. 17

INPUT 5 terminal ................................................. 19

INPUT button ....................................................... 32

Intake vent ........................................................... 73

Kensington Security Standard connector ............ 11

KEYSTONE button .............................................. 36

Keystone correction ............................................. 36

Index

Lamp .................................................................... 76

Lamp replacement indicator ................................ 32

Lens cap .............................................................. 10

Lens shift dial ....................................................... 27

LIGHT button ....................................................... 12

Lightness ............................................................. 51

MENU button ....................................................... 32

NORMAL .............................................................. 60

Optional accessories ........................................... 14

OSD Display ........................................................ 64

PDF ........................................................................ 9

Phase ................................................................... 53

PICTURE SETTING button ................................. 47

Power (ON/OFF) buttons..................................... 32

Power cord ........................................................... 16

Power indicator .................................................... 32

PRJ mode ............................................................ 69

Progressive Mode ................................................ 46

Remote control .................................................... 12

Remote control sensor ........................................ 13

Remote control signal transmitters ...................... 13

Replacing the lamp .............................................. 76

RESIZE button ..................................................... 58

Reversing/Inverting Projected Images ................ 69

RGB/COMP. button .............................................. 18

RS-232C terminal ................................................ 23

Save Setting ........................................................ 53

Select Setting....................................................... 54

Selecting the on-screen display language .......... 34

SharpVision Manager ............................................ 9

SIDE BAR ............................................................ 59

Signal Info ............................................................ 55

Signal Type .......................................................... 65

SMART STRETCH .............................................. 59

Special Modes ..................................................... 54

Status ................................................................... 70

STRETCH ............................................................ 59

Supplied accessories........................................... 14

Target ................................................................... 50

Temperature warning indicator ............................ 74

Terminal cover ..................................................... 11

UNDO button ....................................................... 37

Video System ....................................................... 66

WIRED R/C JACK ............................................... 24

WIRED REMOTE control input terminal ............. 24

Zoom knob ........................................................... 26

Page 93

Appendix

-91

CONSUMER LIMITED WARRANTY

SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the “Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.

This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or modified in design or construction.

In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer.

The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.

The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

Model Specific Section (In-Home Service)

Your Product Model Number & Description:

Warranty Period for this Product:

Additional Item(s) Excluded from Warranty Coverage (if any):

Where to Obtain Service:

What to do to Obtain Service:

XV-Z10000 Projector

(Be sure to have this information available when you need service for your Product.)

One (1) year parts and labor from date of purchase except for the Projector Lamp for which the warranty period is ninety (90) days from date of purchase. After the ninety (90) day warranty period on the Projector Lamp, parts and labor for a lamp replacement are the responsibility of the consumer.

Cleaning of Optical System and/or replacement of any filter. Labor & materials required to remove and reinstall a suspended projector in installations not accessible with a standard (8' step) ladder or ceilings exceeding 12’ in height. Labor & materials required to remove and reinstall a projector in complex systems including, but not limited to, projectors installed in custom enclosures, projectors connected to third party control and automation systems, and realignment of projectors installed in “mirrored” rear projection enclosures.

From a Sharp Authorized Servicer located in the United States. To find the location of the nearest Sharp Authorized Servicer, call Sharp toll free at 1-800-BE-SHARP. Contact your Sharp Authorized Servicer to obtain in-home service for this Product. The Servicer will come to your home and if necessary to remove the Product for repair at the Servicer’s facility, the Servicer will reinstall it upon completion of repair. Be sure to have Proof of Purchase available.

VALID IN USA ONLY

TO OBTAIN PRODUCT INFORMATION, CALL 1-877-DTV-SHARP OR VISIT www.sharpusa.com.

Page 94

-92

LIMITED WARRANTY

Consumer Electronics Products

Congratulations on your purchase!

Sharp Electronics of Canada Ltd. (hereinafter called Sharp ) gives the following express warranty to the first consumer purchaser for this Sharp brand product, when shipped in its original container and sold or distributed in Canada by Sharp or by an Authorized Sharp Dealer:

Sharp warrants that this product is free, under normal use and maintenance, from any defects in material and workmanship. If any such defects should be found in this product within the applicable warranty period, Sharp shall, at its option, repair or replace the product as specified herein.

This warranty shall not apply to: (a) Any defects caused or repairs required as a result of abusive operation, negligence, accident, improper installation or inappropriate

use as outlined in the owner s manual.

(b) Any Sharp product tampered with, modified, adjusted or repaired by any party other than Sharp, Sharp s Authorized Service

Centres or Sharp s Authorized Servicing Dealers.

(c) Damage caused or repairs required as a result of the use with items not specified or approved by Sharp, including but not limited

to head cleaning tapes and chemical cleaning agents.

(d) Any replacement of accessories, glassware, consumable or peripheral items required through normal use of the product including

but not limited to earphones, remote controls, AC adapters, batteries, temperature probe, stylus, trays, filters, belts, ribbons,

cables and paper. (e) Any cosmetic damage to the surface or exterior that has been defaced or caused by normal wear and tear. (f) Any damage caused by external or environmental conditions, including but not limited to transmission line/power line voltage or

liquid spillage. (g) Any product received without appropriate model, serial number and CSA/cUL markings. (h) Any products used for rental or commercial purposes. (i) Any installation, setup and/or programming charges.

Should this Sharp product fail to operate during the warranty period, warranty service may be obtained upon delivery of the Sharp product together with proof of purchase and a copy of this LIMITED WARRANTY statement to an Authorized Sharp Service Centre or an Authorized Sharp Servicing Dealer. In home warranty service may be provided at Sharp s discretion on any Sharp television with the screen size of 27 or larger and on any Sharp Over The Range Microwave Oven.

This warranty constitutes the entire express warranty granted by Sharp and no other dealer, service centre or their agent or employee is authorized to extend, enlarge or transfer this warranty on behalf of Sharp. To the extent the law permits, Sharp disclaims any and all liability for direct or indirect damages or losses or for any incidental, special or consequential damages or loss of profits resulting from a defect in material or workmanship relating to the product, including damages for the loss of time or use of this Sharp product or the loss of information. The purchaser will be responsible for any removal, reinstallation, transportation and insurance costs incurred. Correction of defects, in the manner and period of time described herein, constitute complete fulfillment of all obligations and responsibilities of Sharp to the purchaser with respect to the product and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise.

WARRANTY PERIODS

Projector 1 year (bulb 90 days)

To obtain the name and address of the nearest Authorized Sharp Service Centre or Dealer, please contact:

SHARP ELECTRONICS OF CANADA LTD.

SHARP ELECTRONICS OF CANADA LTD. 335 Britannia Road East Mississauga, Ontario L4Z 1W9 (905) 568-7140 Web site: www.sharp.ca

VALID IN CANADA ONLY

Page 95

SHARP CORPORATION

Printed in Japan Imprimé au Japon Impreso en Japón Impresso no Japão TINS-A440WJZZA

XV-Z10000