Sharp VL-ME10S Operating Instruction

MANUAL DE OPERAÇÃO
BRUKSANVISNING
OPERATION MANUAL
VIDEOKAMERA MED FLYTANDE KRISTALLSKÄRM CAMCORDER COM VISOR DE CRISTAL LÍQUIDO LIQUID CRYSTAL DISPLAY CAMCORDER
VL-ME10S
SVENSKA
PORTUGUÊS
ENGLISH
Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/ 23/EEC så som kompletteras av 93/68/EEC.
Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão corrigida pela directiva 93/68/CEE.
This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC.
VARNING:
Detta är en klass A produkt. I hemmiljö kan produkten orsaka störningar på radiomottagningen, i vilket fall användaren kan behöva vidta åtgärder.
ADVERTÊNCIA:
Este é um produto de classe A. Em ambientes domésticos, este produto pode causar interferência de rádio, e em tais casos, o usuário poderá ser obrigado a tomar as devidas providências.
WARNING:
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
POZOR! P¿ED SEJMUTÍM KRYTU NUTNO VYJMOUT SÍfiOVOU VIDLICI ZE SÍfiOVÉ ZÁSUVKY. UPOZORNÊNÍ: OPRAVU SMÍ PROVÁDÊT POUZE ODBORN„ SERVIS.
• Before using the camcorder, please read this operation manual carefully, espe­cially pages ix to xi.
• The table of contents is located on pages xii to xiv.
• The illustrations of the screen and the actual screen can be different.
OPERATION MANUAL
WARNING
TO PREVENT SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN
CAUTION
To prevent shock, do not open the cabinet. No user serviceable parts inside. Refer servicing to qualified dealer or service centre.
ENGLISH
OR MOISTURE.
This equipment should be used with the recommended AC adapter or battery pack.
CAUTION
To prevent electric shocks and fire hazards, do NOT use any other power source.
Important:
Audio-visual material may consist of copyrighted works which must not be recorded without the authority of the owner of the copyright. Please refer to relevant laws in your country.
NOTE
The LCD panel of this camcorder is a very high technology product with close to 90,000 thin-film transistors*, giving you fine picture detail. Occasionally, a pixel may appear on the screen as a fixed point of blue, green, red, or black. Please note that this does not affect the performance of your camcorder.
*Specifications are subject to change without notice.
WARNING
To prevent the MultiMediaCard and SD Memory Card from being swallowed by children, keep these items out of their reach. If swallowed, seek medical advice immediately.
Power supply:
This unit can be operated by connecting it to either the AC adapter or battery pack. The AC adapter incorporates the AUTO VOLTAGE (AC 110–240 V, 50/60 Hz) function.
ENGLISH
Trademarks
• Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
• Adobe Acrobat Reader is a trademark of Adobe Systems Incorporated.
• DPOF is a trademark of CANON INC., Eastman Kodak Company, Fuji Photo Film Co., Ltd., and Matsushita Electric Industrial Co., Ltd.
• All other brand or product names are registered trademarks or trademarks of their respective holders.
Quick Operation Guide
mark
Quick Operation Guide
Please consult this operation manual further for details on these and other functions of your camcorder.
Charging the Battery Pack 1 Connect the supplied power cord to the
AC power socket on the AC adapter/ battery charger, and insert the AC plug into a power outlet.
2 Align the d mark on the battery pack
with the f mark on the charger (1) and guide the battery into the groove. Pressing the battery (2), slide it in the direction of the arrow (3) until it locks into place.
• The CHARGE indicator lights up. The indicator goes off when the battery is fully charged.
2
1
3
CHARGE indicator
Attaching the Battery Pack
Inserting a Mini DV Cassette 1 Supply power to the camcorder.
2 Hold the camcorder as shown, slide the
cassette compartment door release and open the cassette compartment door completely.
3 Insert the cassette fully with the window
facing upwards and the erasure protect tab facing outwards.
REC
REC SAVE
SAVE
1 Make sure that the POWER switch is set
to OFF.
2 Pull out the viewfinder completely, then
lift it up.
3 Align the mark on the side of the
battery pack with the a mark on the camcorder (1). Press the battery pack and slide it down completely until it locks into place (2).
2
i
1
4 Press the mark gently until the
cassette holder clicks into place.
5 Close the compartment door by pressing
the centre until it clicks into place.
Inserting a Card
70
Using the Viewfinder
This camcorder accepts an SD Memory Card (commercially available) or a MultiMediaCard (supplied) for storage of still images.
1 Make sure that the POWER switch is set
to OFF.
2 Hold the camcorder as shown, and slide
the card slot cover release in the direction of the arrow to open the cover.
3 Insert a card into the slot with the label
facing upwards and the chipped corner facing the lens, and then push it in as far as it will go.
Chipped corner
1 Pull out the viewfinder completely.
2 Raise the viewfinder to better aim the
camcorder depending on your position.
Using the LCD Monitor 1 Press the LCD monitor OPEN release in
the direction of the arrow (1), and open the LCD monitor (2).
4 Close the card slot cover.
Label
2
90
1
2 Adjust the LCD monitor to an angle that
allows easy viewing of the on-screen picture.
180
90
ii
Quick Operation Guide
Camera Recording on Tape
Media Selection switch
Power Zoom buttons
POWER switch
REC START/STOP button
1 Make sure that a Mini DV cassette is
inserted.
2 Remove the lens cap. Pull out the
viewfinder completely or open the LCD monitor.
3 Set the Media Selection
switch to TAPE.
4 Hold down the Lock
button and set the POWER switch to CAMERA.
T o pause recording
Press the REC START/STOP button again.
T o turn the power off
Set the POWER switch to OFF without pressing the Lock button.
Tape Playback 1 Make sure that the recorded Mini DV
cassette is inserted.
2 Open the LCD monitor and adjust the
angle.
3 Set the Media Selection
switch to TAPE.
4 Hold down the Lock
button and set the POWER switch to VCR.
Lock button
5 Press e (or r) to rewind (or fast
forward) the tape to the desired point.
y
e
r
Lock button
5 Press the Power Zoom T (Telephoto) or
W (Wide angle) button to zoom in on or out from the subject.
6 Press the REC START/STOP button to
begin recording.
iii
6 Press y to begin playback.
y
To stop playback
REC
Press b.
GAMMA
NORMAL
PL AYBAPLAYBA
CK
10 0 00 33100 00-
­21
PAGE
CK
54
1
2
3
6
00
PB
qw
100-0003100-0003
3/12
100-0003
CARD 3/12
NORMALNORMAL
NORMAL
MULTIMULTI
qw
Card Recording
Media Selection switch
Power Zoom buttons
STILL button
T o turn the power off
Set the POWER switch to OFF without pressing the Lock button.
Card Playback 1 Make sure that the recorded card is
inserted.
2 Open the LCD monitor and adjust the
angle.
3 Set the Media Selection
switch to CARD.
POWER switch
1 Make sure that a card is inserted. 2 Remove the lens cap. Pull out the
viewfinder completely or open the LCD monitor.
3 Set the Media Selection
switch to CARD.
4 Hold down the Lock
button and set the POWER switch to CAMERA.
Lock button
5 Press the Power Zoom buttons to frame
the subject as you desire.
6 Press the STILL button to record a still
image of the subject.
AUTO
CARD
10/ 90
NORMAL
4 Hold down the Lock
Lock button
button and set the POWER switch to VCR.
5 If the image you want to play back does
not appear, press q or w to scroll through the thumbnail images.
qw
6 Press q or w to move the selection
frame to the desired image, and then press PB to set.
The selected image is displayed in full­screen.
PB
GAMMA
GAMMA
iv
Quick Operation Guide
Dual Recording
The Dual Recording function makes it possible to record motion images on a tape and still images on a card.
Media Selection switch
STILL button
POWER switch
REC START/STOP button
1 Make sure that a Mini DV cassette and a
card are inserted.
2 Remove the lens cap. Pull out the
viewfinder completely or open the LCD monitor.
3 Set the Media Selection
switch to DUAL.
6 Press the REC START/STOP button to
begin recording motion images of the subject on a tape.
Press the REC START/STOP button again to pause recording.
AUTO
60
min
GAMMA
FADE
Press the STILL button to record a still image of the subject on a card.
AUTO
60
min
FADE
GAMMA
To turn the power off
Set the POWER switch to OFF without pressing the Lock button.
SRCHSRCH
SRCH
REC
2/98
NORMAL
CARD
CARD 2/98
NORMAL
Q
4 Hold down the Lock
button and set the POWER switch to CAMERA.
Lock button
5 Press the Power Zoom buttons to frame
the subject as you desire.
v
About Your Camcorder
DV Technology
Digital video, DV, is a revolutionary technology that enables recording and playback of high quality images with the use of special digital features previously unavailable with conven­tional analog formats.
DV and conventional video cassette tapes
There are two kinds of DV-format video cassette tapes: the Mini DV cassette and the larger DV cassette used for extended playback and recording. This camcorder only operates with Mini DV cassettes. DV cassettes cannot be used. Be sure to use Mini DV cassettes with the mark.
Mini DV cassette DV cassette
8 mm, VHS, and Beta cassettes cannot be used for playback or recording with this camcorder.
VHS cassette Beta cassette8 mm cassette
SD Memory Cards and MultiMediaCards
SD Memory Cards and MultiMediaCards are compact recording media just 32 mm long and 24 mm wide which support the needs of the digital network society where music, images, games and various other provider services are offered.
• It is possible to use SD Memory Cards (commercially available) and MultiMediaCards (supplied) as recording media for still images with this camcorder. (SmartMedia™ cards and Memory Stick™ media cannot be used.) In this operation manual, “card” refers to these SD Memory Cards and MultiMediaCards.
SD Memory Card MultiMediaCard
SmartMedia™ card Memory Stick™ media
Note:
• This camcorder reproduces the highest picture quality when used with an ME tape. It is recom­mended that you use an ME tape for high-quality recording and playback.
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineer­ing or disassembly is prohibited.
• SD Memory Cards are superior to MultiMediaCards in terms of copyright protection functions and high-speed transfer.
• SD Memory Cards are compatible with MultiMediaCards, and data stored on MultiMediaCards can be used with SD Memory Cards.
vi
Supplied Accessories
Standard-life
battery pack
BT-L221
AC adapter/
battery charger Power cord
DC cable
CR2025 type
lithium battery
DV cable
8 MB
MultiMediaCard
Infrared
remote control
Earphones connecting
cable
PixLab Video
Capture Software
(Lite version) PC connecting cable
AA battery for
remote control × 2
Shoulder strap
Audio/video/S-video
cable
Lens cap
Zoom microphone Windscreen
vii
Optional Accessories
Standard-life
battery pack
BT-L221
IR & Flash Light
VR-3VIF
Extended-life
battery pack
BT-L441
Note:
• When using the IR & Flash Light VR-3VIF with this camcorder, it can only be used as a flash.
Standard-life intelligent
battery pack
BT-LS222
Extended-life intelligent
battery pack
BT-LS442A
viii
Precautions
When the camcorder is not in use, make sure to turn off the power, remove the cassette and card, and disconnect the camcorder from the power source.
Do not aim the lens at the sun.
Do not allow direct sunlight to strike the camcorder lens, the viewfinder eyepiece, or the LCD monitor screen, whether or not recording is in progress, as it may damage the CCD sensor or LCD screen surface. Be particularly careful when recording outside.
When shooting in dark places, avoid sudden brightly lit objects or light sources, such as the sun. Otherwise, the image may white out. Should this happen, point the lens in a different direction until the picture returns to normal.
Avoid magnetic sources.
Using the camcorder near strong fluorescent lights, motors, televisions, or other magnetic sources may adversely affect recorded images.
Using the camcorder near a broadcasting station or other powerful transmission source may cause buzzing or picture deterioration.
Avoid shocks and dropping.
Do not drop or otherwise subject the camcorder to hard shocks or strong vibrations. Bumping or striking the unit during recording will generate noise in the recorded image.
Avoid placing the camcorder in close proximity to lighting equipment.
The heat from incandescent lights may deform the camcorder, or cause it to malfunction.
Always respect prohibitions or restrictions on the use of electronic equipment on commercial flights or in other sensitive areas.
Be aware of the temperature and humidity.
You can use your camcorder at 0°C to =40°C, and at 30% to 80% relative humidity. Do not store the unit in an unventilated car in the summer, in direct sunlight, or near strong heat sources; this can result in severe damage to the unit casing and circuitry.
Avoid situations where water , sand, dust or other foreign matter could get on or inside the camcorder, and do not use or leave your camcorder in areas with excessive smoke, steam or moisture.
Such environments can cause malfunctions or cause mildew to form on the lenses. Be sure to keep the unit in a well­ventilated location.
Some small, portable tripods may be difficult to attach and may not be sturdy enough to support your camcorder. Be sure to use only a strong, stable tripod.
When using your camcorder in a cold environment, the LCD monitor screen often appears less bright immediately after the power is turned on. This is not a malfunction. To prevent the camcorder from becoming too cold, wrap it in a thick cloth (a blanket, etc.).
ix
Dew Formation
What is “dew formation”? When cold water is poured into a glass, dew drops form on the glass. This clinging of water drops is called dew formation.
When dew forms in your camcorder. Dew will gradually form on the head drum of your camcorder and make the video tape stick to the head. This causes damage both to the head and the tape. When dew forma­tion occurs, recording and playback may not function properly. Dew is likely to form in the following circum­stances: —When moving the camcorder from a cold
place to a warm place.
—When placing the camcorder in a cold
room which is then heated rapidly.
—When moving the camcorder outdoors from
an air conditioned room.
—When placing the camcorder in the direct
path of air blowing from an air conditioner.
—When placing the
camcorder in a humid room.
How to prevent trouble due to dew
formation.
When using the camcorder in a place where dew formation is likely to occur, allow the camcorder and the video tape to acclimatise to the surroundings for about one hour. For example, when bringing the camcorder indoors after skiing, place it in a plastic bag.
“Dew” warning feature If dew forms, the word “DEW” flashes on the screen, and the power will automatically turn off in approximately 10 seconds.
1 If “DEW” flashes, remove the cassette,
leave the cassette compartment open, and wait for a few hours to allow the camcorder to acclimatise to the surround­ing temperature.
2 To use the camcorder again, turn on the
power after waiting for a few hours. Be sure that “DEW” has disappeared.
3 Do not insert a cassette while “DEW” is
flashing; this may result in damage to the tape.
4 Since dew forms gradually, it may take 10
to 15 minutes before the dew warning feature engages.
Plastic bag
1 Be sure to tightly seal the plastic bag
containing the camcorder.
2 Remove the bag when the air temperature
inside it reaches the temperature of the room.
x
Precautions
CLEANING
START
STOP
Dirty Video Heads
Using the camcorder when the video tape is dirty may cause the heads to clog, producing noise on the recorded image or preventing the image from being recorded at all.
If the video heads become clogged, the
indicator appears on the screen. Contact the nearest SHARP service centre or your dealer for further advice.
Using a Cleaning Tape (Commercially Available)
Video head cleaning can be done by using a commercially available cleaning tape.
Notes:
Excessive use of the cleaning tape, however,
may cause damage to the video heads. Please read the instructions accompanying the cleaning tape carefully before using it.
The fast forward and rewind functions cannot be
used when the cleaning tape is in the camcorder.
Media Selection switch
3 Set the Media Selection
switch to TAPE.
4 Hold down the Lock
Lock button
button and set the POWER switch to VCR.
The video head cleaning screen appears.
5 Press START to begin video head
cleaning.
•“NOW CLEANING flashes during cleaning.
CLEANING
CLEANI NGNOW
START
STOP
After about 20 seconds, video head cleaning automatically finishes, and EJECT THE CASSETTE. is displayed.
POWER switch
1 Insert a cleaning tape into the
camcorder.
Follow the procedure on page 14 to insert and remove the cleaning tape.
2 Open the LCD monitor and adjust the
angle.
xi
6 Remove the cleaning tape.
To cancel cleaning, press STOP.
Contents
References
Operation
Operation References
Preparation
Basic Operations
Part Names ............................................................. 1
Quick Reference Index ........................................... 4
On-screen Display Index ........................................ 5
Warning Indicators .................................................. 9
Charging the Battery Pack ................................... 11
Attaching and Removing the Battery Pack .......... 12
Powering the Camcorder from an AC Outlet ....... 13
Inserting and Removing a Mini DV Cassette ....... 14
Inserting and Removing a Card ............................ 15
Installing the Lithium Memory Battery .................. 16
Selecting the Language for the On-Screen
Display ................................................................ 17
Setting the Area, Date and Time ..........................18
Using the Lens Cap .............................................. 19
Adjusting the Hand Strap ..................................... 20
Attaching the Shoulder Strap ............................... 20
Using the Viewfinder ............................................. 21
Using the LCD Monitor.......................................... 22
Camera Recording
Easy Camera Recording on Tape in Full Auto
Mode................................................................... 23
Zooming ................................................................ 24
Tips on Recording Positions ................................. 24
Remaining Tape Time Display .............................. 25
Remaining Battery Power Display ........................ 25
Playback
Tape Playback....................................................... 26
Volume Control...................................................... 27
Video Search......................................................... 27
Still......................................................................... 27
Watching the Playback on a TV ............................ 28
Preparation
Operations
Basic
Summary of
Operations
Features
Useful
Advanced
Features
Digital Still Camera
Features
Summary of Operations
Selecting the Camcorder Mode ............................ 29
Using the Controls ................................................ 30
Selecting the User Mode ...................................... 31
Using the Menu Screens....................................... 32
Appendix
xii
Contents
Be sure to read “Summary of Operations” on pages 29 to 32 before performing the operations described in the following chapters.
Useful Features
Camera Recording
Recording in LP (Long Play Recording) Mode ..... 33
Selecting the 16-bit Audio Recording Mode......... 34
Digital Image Stabilization (DIS) ........................... 35
Setting the Digital Zoom........................................ 36
Gamma Brightness Compensation ....................... 37
Edit Search............................................................ 38
Quick Return ......................................................... 38
Dual Recording ..................................................... 39
Still Recording on Tape ......................................... 40
Still Recording Effects ........................................... 41
Digital Picture Effects ............................................ 42
Fade In and Fade Out ........................................... 43
Wide Screen (16:9) .............................................. 44
Macro Shots .......................................................... 44
Letting the Subject Monitor the Shot ..................... 45
Auto Focus ............................................................ 45
Playback
Using the Infrared Remote Control ....................... 46
Tape Playback Functions with the Infrared
Remote Control ................................................... 48
Displaying the Date and Time of Recording ......... 49
Using Earphones (Commercially Available) ......... 49
Using the Time Code ............................................ 50
Playback Effects ................................................... 51
Picture Effect Playback ......................................... 52
Playback Zoom ..................................................... 53
Gamma Playback.................................................. 54
Multiple Strobe Playback ...................................... 54
Advanced Features
xiii
Camera Recording
Manual Focus........................................................ 55
Setting the Shutter Speed ..................................... 57
Scene Menu (Programme AE) .............................. 59
Adjusting the White Balance ................................. 60
Manual Exposure .................................................. 61
Setting the Camcorder to Full Auto Mode............. 62
Using the Zoom Microphone ................................ 63
Windbreak ............................................................. 64
Dialogue Recording .............................................. 64
Advanced Features
Playback
Editing ................................................................... 65
Editing with the DV Terminal (IEEE1394) .............. 66
Audio Dubbing Feature......................................... 67
Selecting the Audio Playback Mode ..................... 69
Using the Camcorder with Your Computer ........... 70
Digital Still Camera Features
Appendix
Camera Recording
Card Recording .................................................... 72
Selecting the Picture Quality ................................. 73
Recording with the Guide Frame .......................... 74
Recording with the Self-timer ................................ 75
Using the Flash Light (Optional Accessory) ......... 76
Formatting a Card ................................................. 77
Playback
Card Playback ...................................................... 78
Delete-protection .................................................. 79
Deleting Stored Images ........................................ 80
Slide Show Playback............................................. 82
Dubbing Images from a Card to a Tape ............... 83
Directly Transferring the Data on a Card
to a Computer ..................................................... 84
Print Order............................................................. 85
Picture/Backlight Adjustments .............................. 88
Setting the Confirmation Sound ............................ 89
Selecting Summer Time ........................................ 90
World Clock........................................................... 91
Useful Information ................................................. 93
Demonstration Mode............................................. 99
Before Requesting Service ................................. 100
Specifications...................................................... 102
xiv
Operation References
Operation References
Part Names
Operation
References
For details on the use of each part, refer to the page number indicated in brackets.
Front view
Power Zoom W (Wide angle) / T (Telephoto) control buttons [p. 24] / VOLume control buttons [p. 27]
Accessory shoe [pp. 63, 76]
Stereo microphone
1
Zoom lens
[p. 67]
CONTROL dial [p. 30]
EarPHONES jack [p. 49]
Infrared remote sensor [p. 47]
Left view
EASY/MANUAL/AUTO Selection switch [pp. 55–62]
References
Operation
MENU/DISPLAY button
LCD monitor [p. 22]
LCD monitor OPEN
Bottom view
[p. 30]
release [p. 22]
Viewfinder [p. 21]
Dioptre adjustment dial [p. 21]
Power source UNLOCK release [pp. 12, 13]
Power source connection panel [pp. 12, 13]
Shoulder strap loop [p. 20]
Tripod socket
2
Operation References
Operation
Right view
References
Media Selection switch (DUAL/TAPE/CARD
selection switch)
RECord START/STOP
button [pp. 23, 39]
White Balance (W/B) button [p. 60]
selection switch) [p. 29]
STILL button
[pp. 3941, 54, 72]
POWER switch
(CAMERA/VCR
[pp. 29, 30]
PC COMMUNICATION
jack [p. 70]
Shoulder strap loop [p. 20]
Terminal cover [p. 28]
DV terminal [p. 66]
Audio/Video=S-video (AV=S) terminal [pp. 28, 66]
Speaker [p. 26]
Hand strap [p. 20]
When the cassette compartment door is open
Lithium battery holder [p. 16]
Cassette compartment
door [p. 14]
mark [p. 14]
3
Card slot cover [p. 15]
Card slot [p. 15]
Card slot cover release [p. 15]
Cassette holder [p. 14]
Cassette compartment door release [p. 14]
Quick Reference Index
This index lists some example uses of the camcorder’s features.
• To record the subject with higher-quality audio.
—See page 34 (Selecting the 16-bit Audio Recording Mode)
• To record powerful close-up images.
—See page 36 (Setting the Digital Zoom)
• To record a backlit subject.
—See page 37 (Gamma Brightness Compensation) or page 61 (Manual
Exposure)
• To quickly return the tape to the end of the last recorded scene after playback.
—See page 38 (Quick Return)
• To record yourself in the scene while monitoring the shot.
—See page 45 (Letting the Subject Monitor the Shot)
• To enlarge any part of the picture during playback.
—See page 53 (Playback Zoom)
• To brighten the dark portion of the playback images without changing the bright portion.
—See page 54 (Gamma Playback)
• To focus on an off-centred subject.
—See page 55 (Manual Focus)
References
Operation
• To record with natural colour.
—See page 60 (Adjusting the White Balance)
• To minimize blurring when recording sports events, etc.
—See page 59 (Scene Menu)
• To record the zoomed-in picture of a distant subject along with the audio for that subject.
—See page 63 (Using the Zoom Microphone)
• To record still images on a card so that the images may be easily read into a computer.
—See page 72 (Card Recording)
4
Operation References
On-screen Display Index
Operation
References
For details on the use of each function, refer to the page number indicated.
TAPE-CAMERA/DUAL-CAMERA mode
AUTO
p. 25
p. 25
min
90
GAMMA
FADE
MANUAL SE T
M
AN. FOCUS SHUT. SPEE D EXPOSURE PI C. EFFECT SCENE MENU QK.
RETURN
DIS
RETURN
as
L I GHT
AUTO
p. 35
p. 23
pp. 31, 62
p. 33
LP
SRCH
SET
EASY mode (p. 31)
MENU
RETURN
QK. WIND SOUND DISPLAY RETURN
p. 38 p. 64 p. 89 p. 49
MANUAL SET
M
AN. FOCUS
SHUT. SP EED
EXPOSURE PIC.EFFECT SCENE MENU QK.
RET URN
DIS
RET URN
CAMERA SET
REC PHOTO SNAP SNAP EFF. DGTL
TAPE
619:
RET URN
AUDIO SET
AUDI O MODE ZOOM MI C W
IND
DIALOG REC RETURN
OTHERS
SOUND
TIME
OUT
TC DEMO LA NGU AGE
RETURN
LCD VF SET
BACKL I GHT LCD BRI GHT LCD COLOUR
BR I GHT
VF
RET URN
CLOCK SET
DISPLAY AREA SUMR SET T I NG 12H 24H
RET URN
MODE
ZOOM SPE ED
CODE
MODE
TIME
p. 55 p. 57 p. 61 p. 42 p. 59 p. 38 p. 35
p. 73 p. 40 p. 41 p. 36 p. 33 p. 44
p. 34 p. 63 p. 64 p. 64
p. 89 p. 50 p. 50 p. 99 p. 17
p. 88
p. 49 pp. 18, 91 p. 90 p. 18 p. 19
5
TAPE-VCR mode
+
2
AUDIO
1
p. 25
y
e
PLAYBACK SE T
AUDI O DUB AUDI O
EFFECT
PIC. PB EFFECT M
ULTI FRAME
RETURN
as
Note:
See pages 29 to 32 for the procedure to display the desired screen.
SET
p. 69
r
d
GAMMA
PLAYBACK SE T
AUDI O DUB AUDI O
EFFECT
PIC. PB EFFECT M
ULTI FRAME
RETURN
OTHERS
REMO T E SOUND TIME CODE TC OUT
RETURN
LCD
VF SE T
BACKL I GHT LCD BRI GHT LCD COLOUR
BRI GHT
VF
RETURN
CLOCK SET
DISPLAY
RETURN
p. 68 p. 69 p. 52 p. 51 p. 54
p. 46 p. 89 p. 50 p. 50
p. 88
p. 49
References
Operation
6
Operation References
Operation
References
CARD-CAMERA mode
AUTO
GAMMA
MANUA L S E T
M
AN. FOCUS SHUT. S PEED EXPOSURE PIC. EFFECT SCENE SEL F T IMER DIS
RETURN
as
p. 72
MENU
SET
CARD
NORMAL
CARD
AUTO
9001
pp. 31, 62
EASY mode (p. 31)
MENU
SELF
TIMER SOUND DI SPLAY
RETURN
p. 75 p. 89 p. 49
CARD
MANU AL SET
M
AN. F OCUS
9001
SHUT. SP EED EXPOSURE PI C. EFFECT SCENE
MENU SEL F T IMER DIS
RETURN
CAMERA SE T
REC MODE SNAP EFF . DGTL ZOOM
GUIDE
FRM
F LASH
RETURN
OTHERS
FORMAT SOUND DEMO
MOD E
LANGUAGE
RETURN
LCD VF SET
BACKL I GHT LCD BRI GHT LCD COLOUR
BRI GHT
VF
RET URN
CLOCK SE T
DISPLAY
AREA
TIMESUMR
SET T I NG 12H 24H
RETURN
p. 55 p. 57 p. 61 p. 42 p. 59 p. 75 p. 35
p. 73 p. 41 p. 36 p. 74 p. 76
p. 77 p. 89 p. 99 p. 17
p. 88
p. 49 pp. 18, 91 p. 90 p. 18 p. 19
7
CARD-VCR mode
PLAYBACK
NORMAL
PB
100 0001-
PAGE
qw
321
654
1/2
PLAYBACK SE T
SL I DE SHO
EFFECTPIC. PROTE C T DELETE DELETE ALL PRI . ORDER
RETURN
as
W
SET
p. 78
Note:
See pages 29 to 32 for the procedure to display the desired screen.
CARD
PLAYBACK SE T
SL I DE SHO
EFFECTPIC. PROTE C T DELETE DELETE ALL PR I . ORDER
RETURN
OTHERS
REMOTE SOUND
RETURN
LCD VF SET
BACKL IGHT LCD BRIGHT LCD COLOUR
BRI GHT
VF
RETURN
CLOCK S ET
DISPLAY
RETURN
References
Operation
p. 82
W
p. 52 p. 79 p. 80 p. 81 p. 85
p. 46 p. 89
p. 88
p. 49
8
Operation References
Warning Indicators
Operation
References
If a warning indicator appears on the screen, follow the specified instructions.
Displayed for the first
3 seconds
INSERT
A CASSE TTE.
EJECT THE
CASSETTE.
CASSETTE NOT
RECORDABL E.
THE
TAPE
ENDS SOON.
CHANGE THE
CASSETTE.
BAT TE RY IS
TOO LOW.
DEW
LAMP
Displayed after
3 seconds
EJECT THE
CASSETTE.
PROTEC T. TAB
TAPE END
TAPE END
DEW
LAMP
Description of warning
There is no video cassette in the camcorder. Insert a cassette (see page 14).
The video cassette is defective and should be removed (see page 14).
The erasure protect tab on the video cassette has been slid to the record-protect position, preventing recording (see page 95).
The tape is about to end. Prepare a new cassette (see page 14).
The tape has reached the end. Replace it with a new cassette (see page 14).
The battery is almost depleted. Replace it with a fully charged battery pack (see pages 11 and 12).
Dew has formed inside the camcorder. Wait for a few hours until the dew disappears (see page x). About 10 seconds after this warning appears, the camcorder automatically turns off.
The video heads are clogged and should be cleaned (see page xi).
The fluorescent lamp behind the LCD monitor is close to the end of its service life. Call your local authorized Sharp dealer to have it replaced.
All warnings will be indicated by displayed in the centre of the screen if the vertical rotation of the LCD monitor is between 135° and 180° when in one of the CAMERA modes, or if one of the manual screen is displayed. To check the type of warning, rotate the monitor back to within 135°, or press the MENU/ DISPLAY button to turn off the manual screen.
9
References
Operation
Displayed
for 5 seconds
NO
MEMORY CARD
MEMORY
CARD
FULL
NO DATA ON
MEMORY CA RD
MEMORY C ARD
ERROR
FORMAT
MEMORY C ARD
MEMORY CA RD
PROTECTED
DAT A PROTECTED
MEMORY C ARD
READ E RROR
Description of warning
The card is not inserted or is inserted incorrectly. Check how the card is inserted (see page 15).
The capacity of the card is full and cannot store any more images. Delete unnecessary images (see pages 80 and 81) or replace the card with a new one (see page 15).
The card has no images recorded in the format the camcorder can recognize.
The images in the card are corrupted or recorded in a format which is not compatible with this camcorder. Format the card to use it with this camcorder (see page 77).
The card has not been formatted with this camcorder. Format the card (see page 77).
The card is write-protected (see page 97).
You are trying to delete a protected image. Cancel the protection setting to delete the image (see page 79).
The selected image cannot be read by this camcorder. Format the card to use it with this camcorder (see page 77).
CANNOT
STORE DATA
Note:
indicates a flashing display.
The card cannot record any data due to a problem with the card or data on the card. Replace the card (see page 15).
10
Preparation
Preparation
Charging the Battery Pack
Charge the battery pack with the supplied AC adapter/battery charger before use.
Note:
• Remove the DC cable from the AC adapter/ battery charger when charging the battery pack.
Preparation
1 Connect the supplied power cord to the
AC power socket on the AC adapter/ battery charger, and insert the AC plug into a power outlet.
• The POWER indicator lights up.
AC power socket
POWER indicator
To power outlet
2 Align the d mark on the battery pack
with the f mark on the charger (1) and guide the battery into the groove. Pressing the battery (2), slide it in the direction of the arrow (3) until it locks into place.
• The CHARGE indicator lights up.
2
1
3
CHARGE indicator
• The CHARGE indicator goes off when the battery is fully charged.
3 Slide the battery pack in the direction of
the arrow (1), and remove it (2). Then, remove the AC plug of the power cord from the power outlet.
2
Charging time and maximum continuous recording and playback times in TAPE modes
Max.
continuous
pack
Charging
time
100 160
190
Battery
BT-L221
BT-LS222
BT-L441
BT-LS442A
• The chart specifies the approximate times in minutes.
Notes:
Charge the battery pack between 10°C and 30°C. The battery pack may not charge properly at temperatures too low or too high.
The battery pack and charger become warm during charging. This is not a malfunction.
Using the zoom (see page 24) and other functions or turning the power on and off frequently will increase power consumption. This may result in a decrease of more than 50% in the actual recording time compared to the maximum continuous recording time listed above.
The charging time and recording time may vary depending on the ambient temperature and the condition of the battery pack.
• Even when the battery pack is not used, the capacity of the battery pack will naturally deteriorate over time. To limit deterioration of the battery pack capacity, perform the procedure in “Extending battery pack life” on page 94 at least once every six months.
• See page 93 for more information on using the battery pack.
Caution:
• Charge only SHARP model BT-L221, BT-LS222, BT-L441, or BT-LS442A battery packs. Other types of battery packs may burst, causing personal injury and damage.
recording time
LCD
120 240
290
LCD
open
100 200
240
closed
Max.
continuous
playback
time
on LCD
100 200
240
11
1
Attaching and Removing the Battery Pack
Attaching the Battery Pack
1 Make sure that the POWER switch is set
to OFF.
4 Lower the viewfinder, and push it in
completely.
1
2
Removing the Battery Pack
Preparation
POWER switch
2 Pull out the viewfinder completely (1),
and then lift it up (2).
2
Power source connection panel
1
3 Align the mark on the side of the
battery pack with the a mark on the camcorder (1). Press the battery pack and slide it down completely until it locks into place (2).
2
1
1 Perform steps 1 and 2 of “Attaching the
Battery Pack”.
2 Press and hold the power source
UNLOCK release in the direction of the arrow (1), then slide the battery pack up and take it out (2).
1
Power source UNLOCK release
Cautions:
BEFORE REMOVING THE BATTERY PACK, ALWAYS STOP RECORDING OR PLAYBACK AND TURN THE POWER OFF. Removing the
battery pack while shooting or during playback may damage the tape by causing it to wrap around the video head drum or may destroy the card, rendering it unreadable and unwritable.
Remove the battery pack from the camcorder if the camcorder is not to be used for a long period of time.
Use only SHARP model BT-L221, BT-LS222, BT­L441, or BT-LS442A battery packs with this camcorder. Use of other batteries may present a risk of fire or explosion.
2
12
Preparation
Powering the Camcorder from an AC Outlet
You can also power the camcorder from a power outlet by using the supplied AC adapter/ battery charger, power cord and DC cable.
Caution:
Preparation
The supplied AC adapter/battery charger is specially designed for use with this camcorder, and should not be used as a power supply for other camcorders.
1 Make sure that the POWER switch is set
to OFF.
2 Pull out the viewfinder completely, and
then lift it up.
3 Align the mark on the side of the DC
cable connecting plate with the a mark on the camcorder (1). Press the connecting plate and slide it down completely until it locks into place (2).
DC cable connecting plate
2
5 Insert the DC cable plug into the DC
OUT jack on the AC adapter. Connect the power cord to the AC adapter, and insert the AC plug into a power outlet.
The POWER indicator on the AC adapter lights up, and the camcorder is supplied with power.
DC OUT jack
POWER indicator
To power outlet
Note:
When the AC adapter/battery charger is used to power the camcorder, it cannot be used to charge the battery pack.
Removing the DC cable from the camcorder
Perform steps 1 and 2 above. Press and hold the power source UNLOCK release in the direction of the arrow (1), then slide the connecting plate up and take it out (2).
1
4 Lower the viewfinder, and push it in
completely.
13
1
Power source UNLOCK release
Cautions:
BEFORE REMOVING THE DC CABLE, ALWAYS STOP RECORDING OR PLAYBACK AND TURN THE PO WER OFF . Removing the
DC cable while shooting or during playback may damage the tape by causing it to wrap around the video head drum or may destroy the card, rendering it unreadable and unwritable.
Disconnect the camcorder from the AC adapter if the camcorder is not to be used for a long period of time.
2
Inserting and Removing a Mini DV Cassette
Inserting a Cassette
1 Supply power to the camcorder. 2 Hold the camcorder as shown in the
figure, slide the cassette compartment door release and open the cassette compartment door completely.
The cassette holder extends and opens automatically.
5 Wait for the cassette holder to fully
retract. Close the compartment door by pressing the centre until it clicks into place.
Preparation
Cassette compartment
door release
3 Insert the cassette fully with the window
facing upwards and the erasure protect tab facing outwards.
Erasure protect tab
REC
REC SAVE
SAVE
4 Press the mark gently until the
cassette holder clicks into place.
The cassette holder retracts automati­cally.
Removing a Cassette
Perform steps 1 and 2 of Inserting a Cas­sette, and then take out the cassette.
Cautions:
Do not hold the camcorder with the cassette compartment door release facing downwards when you are inserting or removing a cassette. It may damage the tape.
Do not try to close the cassette compartment door while the cassette holder is extending or retracting.
Be careful not to get your fingers caught in the cassette holder.
Do not apply force to the cassette holder except when pressing the mark to close it.
If you do not correctly close the cassette holder in step 4, the cassette protection mechanism of the camcorder might eject the cassette. If this happens, repeat the insertion procedure.
Do not attempt to pick up the camcorder by the cassette compartment door.
Remove the cassette if the camcorder is not to be used for a long period of time.
Notes:
If the battery power is too low, you may not be able to eject the cassette. Replace the battery pack with a fully charged one.
See page 95 for more information on the video cassette tapes intended for use with this camcorder.
mark
14
Preparation
Inserting and Removing a Card
This camcorder accepts an SD Memory Card (commercially available) or a MultiMediaCard (supplied) for storage of still images.
Preparation
Inserting a Card
1 Make sure that the POWER switch is set
to OFF.
2 Hold the camcorder as shown in the
figure, and slide the card slot cover release in the direction of the arrow.
The card slot cover is opened.
Card slot cover release
3 Insert a card into the slot with the label
facing upwards and the chipped corner facing the lens, and then push it in as far as it will go.
Removing a Card
1 Perform steps 1 and 2 of Inserting a
Card”.
2 Push the centre of the card edge in to
release the card.
3 Pull the card straight out.
Notes:
The supplied MultiMediaCard is preformatted for immediate use.
See pages 96 and 97 for detailed information on the use of MultiMediaCards and SD Memory Cards.
4 Close the card slot cover.
15
Label
Chipped corner
Caution:
Do not remove the card from the camcorder while data is being recorded on the card (the O indicator flashes on the screen), as this may result in deletion of images on the card or damage to the card itself.
Installing the Lithium Memory Battery
4 Insert the lithium battery holder back into
the compartment.
The supplied lithium battery is used to store the memory of the date and time settings.
1 Slide the card slot cover release in the
direction of the arrow to open the card slot cover.
Card slot cover release
2 Pull out the lithium battery holder using
the tip of a ballpoint pen or other pointed object.
Lithium battery holder
3 Insert the lithium battery into the holder
with the = side of the battery facing the + side of the holder.
Preparation
5 Close the card slot cover.
Note:
It is recommended to immediately set the date and time after inserting a lithium battery. Not setting the date and time causes extra wear of the lithium battery.
Removing the lithium battery
Perform steps 1 and 2 above, and then lift out the lithium battery from the battery holder.
Note:
Replace the battery with a new CR2025 lithium battery when the time indicator of the camcorder starts to fall behind the correct time.
Notes on the Use of the Lithium Battery
CAUTION: Danger of explosion if battery is
incorrectly replaced. Replace only with the same or equivalent type CR2025 recom­mended by the equipment manufacturer.
WARNING KEEP THIS BATTERY AWAY FROM
CHILDREN. IF SWALLOWED, CONSULT A PHYSICIAN IMMEDIATELY FOR EMERGENCY TREATMENT.
CAUTION BATTERY MAY EXPLODE IF MIS-
USED OR INSTALLED WITH POLARITY REVERSED. DO NOT RECHARGE, DISAS­SEMBLE OR DISPOSE OF IN FIRE.
+ mark
Do not short-circuit, recharge, disassemble, or heat the lithium battery.
Should the lithium battery leak, wipe the battery compartment and holder clean, and then insert a new battery.
The lithium battery will last about one year under normal usage.
16
Preparation
ENGLI SH
LANGUAGE
DEUTSCH FRAN
Ç
AIS
SET
as
1 1 2
SOUND TIME CODE TC OUT DE MO MODE
LANGUAGE
RETURN
ENGLI SH
OTHERS
SET
as
1 1 2
Selecting the Language for the On-screen Display
This camcorder allows you to choose from among English, German or French for the on­screen display language.
Note:
Preparation
The English, German and French portions of this operation manual are based on the use of on-screen displays in their respective languages. The portions of this manual in other languages, however, are based on the use of English on-screen displays.
MENU/DISPLAY button
POWER switch
Setting the Language
When using the camcorder for the first time, select the desired language for the on-screen display by performing the procedure below.
3 Press f or d (1) to select the desired
language, then press SET (2).
The camcorder will be in Recording Standby mode.
Changing the Language
1 Set the camcorder to TAPE-CAMERA or
CARD-CAMERA mode.
2 Press the MENU/DISPLAY button until
the menu screen appears.
3 Select I, then press SET. Select
“LANGUAGE” (“SPRACHE” or “LANGUE”) (1), then press SET (2).
The language selection screen appears.
1 Press the LCD monitor OPEN release
button (1) and open the LCD monitor (2).
2
1
2 Hold down the Lock
button and set the POWER switch to CAMERA.
The language selection screen appears on the LCD screen.
17
LCD monitor OPEN release button
Lock botton
LANGUAGE
ENGLI SH
DEUTSCH
Ç
FRAN
AIS
4 Perform step 3 in Setting the
Language”.
The menu screen is displayed in the language selected.
5 Press the MENU/DISPLAY button to
turn off the menu screen.
Setting the Area, Date and
SET
as
1 1 2
2. 000
:
1 2001.
SE TT I NG
DISPLAY SUMR T I ME
AREA SETT I NG RETURN
12H 24H
LONDON1
CLOCK SE T
SET
as
1 1 2
Time
Available modes: TAPE-CAMERA, DUAL-
CAMERA, CARD-CAMERA
Example: Setting the date to 2 June 2002 (2.
6.2002) and the time to 10:30 am (10:30) in Paris.
Notes:
Before performing the procedure below, make sure that the lithium battery has been installed (see page 16).
If you are in an area that observes summer time, set the time to the standard time. You can then correct it for summer time by performing the procedure on page 90.
Media Selection switch
3 Press the MENU/DISPLAY button until
the menu screen appears, and then press SET.
4 Press f or d (1) until 2 PARIS
appears, then press SET (2).
CLOCK SE T
as
DISPLAY
SET
AREA
SUMR T IME SETT I NG 12H 24H RETURN
PARIS2
Preparation
POWER switch
1 Press the LCD monitor OPEN release in
the direction of the arrow (1) and open the LCD monitor (2).
2
2 Hold down the Lock
button and set the POWER switch to CAMERA.
The LCD screen turns on.
LCD monitor
OPEN release
1
Lock button
as
SET
Note:
See Time Zone Chart and Area Table on pages 91 and 92 for the area number and name of the representative city for your time zone.
5 Press f or d (1) to select SETTING,
then press SET (2).
CLOCK SE T
DISPLAY AREA SUMR T I ME SETT I NG 12H 24H RETURN
as
SET
. :
000
11 2001.
6 Press f or d to select 2 (day), then
press SET.
18
Preparation
7 Press f or d to select 6 (month), then
press SET.
SE TT I NG
2. 6 001. :
000
8 Press f or d to select 2002 (year),
Preparation
then press SET.
SE TT I NG
2.06 2002. :
00
9 Press f or d to select 10 (hour), then
press SET.
2.
SE TT I NG
:
10 00
6 2002.
10 Press f or d to select 30 (minute),
then press SET.
The internal clock now starts operating.
SE TT I NG
2.06 2002. :
10 3
11 Press the MENU/DISPLAY button to
turn off the menu screen.
Changing to the 12-hour Time Mode
1 After performing step 10 above, press f
or d (1) to select 12H/24H, and then press SET (2).
CLOCK SE T
DISPLAY
as
1 1 2
SET
AREA SUMR T I ME SET T I NG 12H 24H RETURN
as
SET
24H
12H
2 Press f or d to select 12H, then
press SET.
21H24H
12H
3 Press the MENU/DISPLAY button to
turn off the menu screen.
Notes:
Providing the date and time have been internally set, they will always be recorded on the tape or
2
card, and you can choose to display them or not (see page 49).
The menu screen automatically turns off if no settings are made within 5 minutes.
You can also adjust the clock in the CLOCK SET menu in DUAL-CAMERA or CARD-CAMERA mode.
Using the Lens Cap
Attach the strap of the lens cap to the hand strap as shown below.
When attaching or removing the lens cap, press both tabs on the top and bottom of the cap.
When recording, hang the hook of the lens cap on the hand strap so that the cap will not get in the way.
Note:
Always replace the lens cap on the lens when the camcorder is not in use.
Tabs
Hook
19
Adjusting the Hand Strap
Attaching the Shoulder Strap
1 Open the hand strap flap (1) and the
grip strap (2).
1
2
2 Loosen the grip strap, pass your right
hand through the loop, and put your thumb on the REC START/STOP button and your forefinger and middle finger on the Power Zoom buttons. Then, pull the grip strap tight until it fits snugly.
Power Zoom buttons
1 Hold one end of the strap and thread it
through the loop on the left side of the power source connection panel.
2 Loosen the strap in the buckle, and feed
the end of the strap through the buckle, as shown.
3 Draw the strap in the direction of the
arrow to secure.
4–6 To attach the other end of the strap to
the loop on the left side of the hand strap, open the hand strap flap, and perform the same procedure.
1
Loop
2
Buckle
3
4
Loop
5
Buckle
6
Preparation
REC START/STOP button
3 Seal the velcro fasteners of the grip
strap and the hand strap flap.
Caution:
Do not swing the camcorder by the hand strap.
20
Preparation
Using the Viewfinder
You can record the subject through the electronic LCD colour viewfinder. You can also watch video playback through the viewfinder.
Viewfinder
Preparation
POWER switch
1 Pull out the viewfinder completely.
You can raise the viewfinder up to 70° to
better aim the camcorder depending on your position.
70
Closing the viewfinder
Lower the viewfinder (1), and push it in completely (2).
1
2
Cautions:
Do not use excessive force when moving the viewfinder.
Do not pick up the camcorder by the viewfinder.
Notes:
The viewfinder automatically turns off when the LCD monitor is opened. If the vertical rotation of the monitor is between 135° and 180° when in one of the CAMERA modes, however, the viewfinder is on and the subject is displayed both in the viewfinder and on the monitor (see page 45).
It is possible to operate the playback functions in TAPE-VCR and CARD-VCR modes and adjust the menu and the manual settings through the viewfinder by using the CONTROL dial. (See page 30 for operation of the CONTROL dial.)
Be sure to close the viewfinder after use.
Adjusting the Dioptre
Adjust the dioptre according to your eyesight when the picture in the viewfinder is not clear.
1 Pull out the viewfinder completely, and
then lift it up.
Caution: Do not try to raise the viewfinder until it is completely pulled out.
2 Hold down the Lock
button and set the POWER switch to CAMERA or VCR.
A picture is displayed in the viewfinder.
21
2 Hold down the Lock button and set the
POWER switch to CAMERA.
3 While looking through the viewfinder,
turn the Dioptre adjustment dial until the indicators in the viewfinder are clearly visible.
Lock button
Dioptre
adjustment dial
Using the LCD Monitor
You can use the LCD monitor to play back recordings that you have made or to watch the subject during recording.
POWER switch
LCD monitor
1 Press the LCD monitor OPEN release in
the direction of the arrow (1), and open the LCD monitor to a 90° angle to the camcorder body (2).
LCD monitor
OPEN release
2
90
1
You can also fold the LCD monitor into the camcorder with the screen facing out for watching playback on the monitor.
3 Hold down the Lock
button and set the POWER switch to CAMERA or VCR.
A picture is displayed on the LCD monitor.
Notes:
Battery consumption is larger when the LCD monitor is open. Use the viewfinder instead of the LCD monitor when you want to save battery power.
Use the viewfinder if the LCD screen becomes difficult to see under bright daylight.
Closing the LCD monitor
Return the LCD monitor to the vertical 90° position with the screen facing in, and fold it into the camcorder until it clicks into place.
Lock button
Preparation
2 Adjust the LCD monitor to an angle that
allows easy viewing of the on-screen picture.
The LCD monitor rotates 270° vertically.
180
90
Caution: Do not try to rotate the LCD monitor vertically until the monitor is completely opened.
Cautions:
Do not use excessive force when moving the LCD monitor.
When closing the LCD monitor, do not tilt it; otherwise the monitor may not close properly and may become damaged.
Do not pick up the camcorder by the LCD monitor.
Do not place the camcorder with the LCD screen facing down.
Note:
Close the LCD monitor completely with the screen facing in when not in use.
22
Basic Operations
Basic Operations
Camera Recording
Camera Recording
Easy Camera Recording on Tape in Full Auto Mode
Available mode: TAPE-CAMERA
• Before you start recording, perform the opera­tions described on pages 11 through 22 to prepare your camcorder for recording.
Media Selection switch
Basic
Operations
POWER switch
REC START/STOP button
1 Remove the lens cap. Pull out the
viewfinder completely or open the LCD monitor.
2 Set the Media Selection
switch to TAPE.
3 Hold down the Lock button and set the
POWER switch to CAMERA.
• The camcorder turns on in TAPE-CAMERA mode, and the picture from the lens is displayed on the screen.
• The camcorder is now ready to record (Recording Standby mode).
AUTO
Lock button
Auto mode indicator
Note: If “AUTO” is not displayed at this time,
set the EASY/MANUAL/AUTO selection switch to AUTO. (See page 62)
4 Press the REC START/STOP button to
begin recording.
To pause recording
Press the REC START/STOP button again. Recording pauses, and the camcorder enters Recording Standby mode.
To turn the power off
Set the POWER switch to OFF without pressing the Lock button.
Notes:
• Battery power is consumed in Recording Standby mode. Turn off the power if you will not be recording again soon.
• If the camcorder remains in Recording Standby mode for more than 5 minutes in TAPE-CAMERA or DUAL-CAMERA mode, the power will automatically turn off to save battery power and to protect the tape from being damaged. (The camcorder will make a confirmation sound when it is left in Recording Standby mode for about 4 minutes.) To resume recording after the power has been turned off, set the POWER switch to OFF and then back to CAMERA.
Maximum continuous recording and actual recording times in TAPE­CAMERA mode
Max. continuous
Battery
pack
BT-L221
BT-LS222
BT-L441 240 200 120 100
BT-LS442A 290 240 150 120
• The chart specifies the approximate times in minutes.
Note:
Using the zoom (see page 24) and other functions or turning the power on and off
REC
frequently will increase power consumption. This may result in a decrease of more than 50% in the actual recording time compared to the maximum continuous recording time listed above.
recording time
LCD
closed
120 100 60 50
LCD
open
PAUSE
Actual
recording time
LCD
closed
LCD
open
23
Zooming
Tips on Recording Positions
Available modes: TAPE-CAMERA, DUAL-
CAMERA, CARD-CAMERA
Zooming allows you to move visually closer to or farther from a subject without physically changing your position. When using optical zoom, it is possible to enlarge the subject up to 10× in TAPE-CAMERA, DUAL-CAMERA or CARD-CAMERA mode.
Zooming in (when you want to centre
attention on the subject)
Wide
angle
Zooming out (when you want to
show the surroundings)
Te le ­photo
To zoom in
Press the Power Zoom T (telephoto) button to get a close-up view (1).
To zoom out
Press the Power Zoom W (wide angle) button to get a wide field of view (2).
12
Power Zoom buttons
To create images that are easy to watch during playback, try to record with a stable posture while steadying your camcorder to prevent the image from shaking.
Holding the camcorder
Put your right hand through the hand strap, and place your left hand under the camcorder for support.
Basic posture
Place your elbows against your sides.
Shooting from a high angle
Turn the LCD monitor
so that the screen faces
downward.
Place the viewfinder eyecup firmly against your eye.
Balance your weight on both legs.
Operations
Basic
Zoom range
2
indicator
The on-screen display shows you the current zoom setting.
The zoom speed depends on how strongly you press the Power Zoom buttons.
Notes:
The camcorder is unable to focus when zooming in on subjects within 1.5 m. The camcorder will automatically zoom out until it is able to focus on the subject. (See page 44 for recording macro shots.)
See page 36 for use of the digital zoom.
Shooting from a low angle Using the viewfinder
Raise the viewfinder
to view the subject.
Using the LCD monitor
Turn the LCD monitor so that the screen faces upward.
Note:
Take care not to touch the microphone with your fingers during recording. It will cause noise on the audio track.
24
Basic Operations Camera Recording
Remaining Tape Time Display
Available modes: TAPE-CAMERA, DUAL-
CAMERA
In TAPE-CAMERA or DUAL-CAMERA mode, an on-screen indicator displays the approximate remaining tape time in minutes.
During camera recording, press the MENU/ DISPLAY button until the remaining recording time indicator appears.
Basic
Operations
30
Remaining tape time indicator
Notes:
• If the battery pack or DC cable are removed from the camcorder and then reattached while the camcorder has a cassette in it, the remaining tape time indicator will not be displayed. In this case, record for about 10 seconds to display the remaining tape time indicator.
The remaining tape time indicator only shows the approximate time left. Also, it varies slightly depending on the length of tape used. (This function is based on the DVM60 tape standard.)
When the remaining tape time reaches 1 minute, a warning indicator will appear. Prepare a new cassette.
Warning indicator Approx. remaining time
THE
TAPE
ENDS SOON.
TAPE END
CHANGE THE
CASSETTE.
TAPE END
FADE
1 min. – 0 min.
0 min. (The tape has
reached the end.)
min
GAMMA
Remaining Battery Power Display
Available modes: all modes
When using the camcorder with the battery pack as the power source, you can turn on and off the remaining battery power display by pressing the MENU/DISPLAY button. If the battery power becomes very low, a warning indicator will appear. Replace the battery pack.
(Green) (Green) (Red)
Notes:
Use the remaining battery power indicator only as an approximate indication.
Variations in the operational status of the camcorder can greatly reduce or increase the remaining operating time displayed.
Use of the zoom functions when the warning indicator is displayed may cause the camcorder to suddenly lose power.
This camcorder supports an intelligent battery function. Use of the optional BT-LS222 or BT­LS442A intelligent battery pack allows the number of minutes of continuous operating time that remains to be displayed on the screen based on the remaining battery power.
210
AUTO
Remaining battery power display
Warning indicator
min
25
Basic Operations
Playback
T ape Playback
Available mode: TAPE-VCR
The LCD monitor screen functions as a handy playback monitor. Nothing needs to be connected, allowing instant on-screen play­back with the sound through the built-in speaker.
Media Selection switch
Speaker
POWER switch
1 Supply power to the camcorder, and
insert the recorded Mini DV cassette.
2 Open the LCD monitor and adjust the
angle.
3 Set the Media Selection
switch to TAPE.
6 Press y to begin playback.
y
To stop playback
Pressd.
To turn the power off
Set the POWER switch to OFF without pressing the Lock button.
Note:
• The tape is automatically rewound when playback reaches the end of the tape.
Watching the Playback in the Viewfinder
You can also watch the playback in the viewfinder by closing the LCD monitor with the screen facing in.
Operations
Basic
4 Hold down the Lock
button and set the POWER switch to VCR.
• The camcorder turns on in TAPE-VCR mode.
Lock button
5 Press e (or r) to rewind (or fast
forward) the tape to the desired point.
y
e
r
CONTROL dial
• To operate the playback functions, turn the CONTROL dial to select the desired playback operation indicator, and then press the dial.
Note:
• You cannot monitor the sound through the speaker when watching the playback in the viewfinder.
26
Basic Operations Playback
Volume Control
Available mode: TAPE-VCR
When the camcorder is in TAPE-VCR mode, you can adjust the volume level of the sound.
Press the VOL. = or - button to increase (1) or decrease (2) the volume. The volume level indicator appears on the screen only during adjustment.
21
Basic
Operations
VOL. buttons
VOLUME
IncreaseDecrease
Video Search
Available mode: TAPE-VCR
The video search function makes it easy to search for a desired scene on the tape.
1 During playback in TAPE-VCR mode,
press e (or r).
The playback picture fast forwards (or reverses).
2 When you find the desired scene, press
y to return to normal playback.
Notes:
The sound is off during search.
Some picture noise appears during search. This
is not a malfunction.
y
Still
Available mode: TAPE-VCR
The still function makes it possible to pause tape playback.
27
During playback in TAPE-VCR mode, press
y.
y
To return to normal playback, press y again.
Notes:
The sound is off in Still mode.
To protect the tape, the camcorder automatically
returns to normal playback if it is left in Still mode for more than 5 minutes.
Watching the Playback on a TV
Available modes: TAPE-VCR, CARD-VCR
You can also connect the camcorder to a TV to allow a larger audience to enjoy video play­back.
Caution:
Make sure that the camcorder, TV, VCR and other equipment to be connected have been turned off before you make connections. Making connections with any of the components left turned on may cause picture noise or a malfunction.
1 Open the terminal cover on the
camcorder.
Terminal cover
2 Connect the camcorder to your TV (or
VCR) with the supplied audio/video/S­video cable, as shown.
CHANNEL
PAUSE /STILL
PLAY
STOP/ EJECT
To S-video
input terminal
POWER
Yellow: To video input jack White: To audio input (L) jack Red: To audio input (R) jack
REC
TV/VCRSET UP
3 Turn on the TV and set it to the “AV” or
“VIDEO” channel. (See the operation manual of your TV.)
When connecting to a TV via a VCR, turn on the VCR and set it to the “AV” or LINE input channel. Operate the TV as you normally do to see the signal from the VCR. (See the operation manuals of your TV and VCR.)
4 Set the POWER switch on the
camcorder to VCR, and begin playback (see pages 26 and 78).
Notes:
If your TV or VCR has a 21-pin Euro-SCART connector, use the RCA/21-pin Euro-SCART conversion connector (QSOCZ0033TAZZ).
21-pin Euro-SCART on TV or VCR
VIDEO AUDIO
Video
S-video terminals are used to separately pass the chroma (colour) and luminance (brightness) components of video signals. They serve to improve the picture quality in both recording and playback. If your TV or VCR has an S-video input terminal, you can use the S-video plug of the supplied audio/video/S-video cable for the video connection on the TV or VCR. (The yellow video plug does not need to be connected to the TV or VCR.)
If your TV or VCR has only one audio input jack, use the white plug for the audio connection on the TV or VCR.
When the camcorder is connected to a TV for play-back, the picture on the TV screen may flicker if the volume on the camcorder is set to maximum. Should this occur, turn the volume down (see page 27).
Close the terminal cover after use.
RCA/21-pin Euro-SCART
0
conversion connector
AUDIO
(QSOCZ0033TAZZ)
(L/MONO)
(R)
Audio R Audio L
Operations
Basic
Audio/video/S-video cable (supplied)
To AV+S terminal
Removing the audio/video/S-video cable from the camcorder
Hold down the catches and pull out the plug.
Caution:
Forcibly pulling on the audio/video/S-video cable without holding down the catches may result in damage.
Catches
28
Useful FeaturesUseful Features
Summary of Operations
Summary of Operations
Summary of Operations
Selecting the Camcorder Mode
This camcorder includes functions for use as both a video camera for recording and playing back images on tape and as a digital still camera for recording and playing back still images on a card. One of the following camcorder modes needs to be set before starting any operations.
TAPE-CAMERA mode — For recording
motion and still images on a tape.
1 Set the Media Selection
switch to TAPE.
2 Hold down the Lock
Operations
Summary of
button and set the POWER switch to CAMERA.
Lock button
CARD-CAMERA mode — For recording
still images on a card.
1 Set the Media Selection
switch to CARD.
Media Selection switch
POWER switch
TAPE-VCR mode — For playing back
motion and still images recorded on a tape.
1 Set the Media Selection
switch to TAPE.
2 Hold down the Lock
button and set the POWER switch to VCR.
CARD-VCR mode — For playing back still
images recorded on a card.
Lock button
1 Set the Media Selection
switch to CARD.
2 Hold down the Lock
button and set the POWER switch to CAMERA.
Lock button
DUAL-CAMERA mode — For recording
motion images on a tape and still images on a card.
1 Set the Media Selection
switch to DUAL.
2 Hold down the Lock
button and set the POWER switch to CAMERA.
Lock button
29
2 Hold down the Lock
button and set the POWER switch to VCR.
Note:
• When the Media Selection switch is set to DUAL and the POWER switch is set to VCR, the camcorder performs the same operation as in TAPE-VCR mode.
Caution:
• Do not change the camcorder mode by operating the Media Selection switch during recording or playback, as this may cause damage to the tape or card.
Lock button
Using the Controls
The following controls on the camcorder can be used to select and operate the various functions, settings and on-screen displays.
POWER switch
MENU/DISPLAY button
CONTROL dial
POWER switch
To turn the power on, hold down the Lock button and set the POWER switch to CAMERA or VCR.
MENU/DISPLAY button
The MENU/DISPLAY button is used to turn the mode screens and on-screen indicators off. You can turn the on-screen indicators back on by pressing the MENU/ DISPLAY button again.
Note:
The tally indicator and warning indicators cannot be deliberately turned off.
CONTROL dial
The CONTROL dial is used to adjust the settings on the menu screen. The procedures for adjusting the menu settings in this operation manual are based upon the use of the five operation buttons under the LCD monitor. To adjust the menu settings with the CONTROL dial, follow the rules below.
1 Turn the CONTROL dial (instead of
pressing a or s) to select the desired item.
Example
CAMERA SET
REC MODE
PHOTO SNAP
EFF.SNAP
DGTL ZOOM
TAPE SPEED
1
69:
RETURN
as
SP
SET
2 Press the CONTROL dial (instead of
pressing SET) to set the selected item.
Example
Summary of
Operations
Lock button
To turn the power off, set the POWER switch to OFF without pressing the Lock button.
CAMERA SET
REC MODE
PHOTO SNAP
EFF.SNAP
DGTL ZOOM
TAPE SPEED
16
9:
RETURN
as
SET
SP
LP
30
Summary of Operations
Summary of Operations
Selecting the User Mode
This camcorder features three user modes for the camera recording functions. The selectable items on the menu screen are different depending on the user mode.
User mode
Auto mode (AUTO): Lets you adjust all menu
settings except manual settings.
Manual mode (MANUAL): Lets you adjust all
settings including the following manual settings. —MAN. FOCUS, SHUT. SPEED, EXPOSURE
Easy mode (EASY): Lets you adjust only the
following basic menu settings. —QK. RETURN, WIND, SOUND, DISPLAY,
SELF TIMER
Operations
Summary of
EASY/MANUAL/AUTO Selection switch
1 Open the LCD monitor and adjust the
angle (see page 22).
2 Set the Media Selection
switch to TAPE or CARD.
3 Hold down the Lock button and set the
POWER switch to CAMERA.
• The user mode indicator is displayed.
AUTO
User mode indicator
Lock botton
4 Set the EASY/MANUAL/AUTO Selection
switch to the desired mode.
Notes:
• All manual settings in Manual mode will be canceled when you set the EASY/MANUAL/ AUTO Selection switch to return to Auto mode.
• There is no user mode for playback functions.
• The example screens in this operation manual assume the use of Auto mode unless otherwise indicated.
31
Using the Menu Screens
OFF
40 200
PHOTO SNAP
REC
EFF.
DGTL ZOOM
SPEED
16 9:
CAME RA SET
MODE
SNAP TAPE RET URN
SET
as
200
PHOTO SNAP
REC
EFF.
DGTL ZOOM
SPEED
16 9:
CAME RA SET
MODE
SNAP TAPE RET URN
SET
as
The menu screens can be used to adjust the various settings of the camcorder.
1 Open the LCD monitor and adjust the
angle (see page 22).
2 Set the Media Selection
switch to TAPE or CARD.
3 Hold down the Lock
button and set the POWER switch to CAMERA or VCR.
Lock button
4 Press the MENU/DISPLAY button until
the menu screen appears.
MANUAL SET
M
AN. FOCUS SHUT. SPEED EXPOSURE
PIC.EFFECT SCENE MENU
QK.
RET URN
DIS RET URN
as
SET
6 Press f or d (1) to select the desired
menu item, then press SET (2).
The available settings for the selected menu item are displayed.
Example
as
SET
1 1 2
7 Press f or d (1) to select the desired
menu setting, then press SET (2).
The selected menu setting is set.
Example
as
SET
1 1 2
To adjust another menu item, select RETURN to returns to the status in step 5 or 6, then repeat the procedure from the point.
Summary of
Operations
5 Press f or d (1) to select the desired
menu screen, then press SET (2).
Example
CAMERA SE T
REC
MODE
as
1 1 2
SET
PHOTO SNAP SNAP
EFF.
SNAP
ZOOM
DGTL
SPE ED
TAPE 16 9: RE T URN
as
SET
To turn off the menu screen
Press the MENU/DISPLAY button.
Notes:
Certain menu items are common among Camcorder modes. If the DISPLAY menu item, for example, is set to “DATE+TIME in TAPE- CAMERA mode, it will be automatically set to
DATE+TIME” in other modes.
The menu items are displayed in yellow when
the corresponding functions are selected. The menu items are displayed in gray when the corresponding functions cannot be selected.
The menu screen automatically turns off if no settings are made within five minutes.
The example screens in this operation manual are for explanation purposes, and may differ slightly from the actual screen displays.
32
Useful Features
Useful Features
Camera Recording
Camera Recording
Recording in LP (Long Play Recording) Mode
Available modes: TAPE-CAMERA, DUAL-
CAMERA
This camcorder allows you to record in LP (Long Play Recording) mode for approximately 50% more recording time with the same picture quality as that in SP (Standard Play Recording) mode.
1 Set the camcorder to TAPE-CAMERA or
DUAL-CAMERA mode (see page 29).
2 Press the MENU/DISPLA Y button until
the menu screen appears.
MANU AL SE T
M
AN. FO CUS SHUT. SP EED EXPOSURE
PI C. EFFECT SCENE MENU
QK.
RETURN
DIS RETURN
Useful
Features
as
SET
3 Select Y, then press SET. Select “TAPE
SPEED” (1), then press SET (2).
CAME RA SET
REC MODE
as
1 1 2
SET
PHOTO SNAP
EFF.SNAP DGTL Z OOM TAPE SPEED 16 9: RETURN
as
SET
SP
LP
5 Press the MENU/DISPLAY button to
turn off the menu screen.
• The Long Play Recording mode indicator appears.
min
45
LP
Long play recording mode indicator
To return to SP mode
Select “SP” in step 4 above.
Notes on the use of LP mode
• To record in LP mode, be sure to use a Mini DV cassette labelled for use with LP mode.
• Frozen images, mosaic-pattern picture noise, audio interruptions or audio loss may occur in the following cases: —When using a tape which is not designated
for use with LP mode.
—When a tape recorded in LP mode under
high-temperature conditions is played back.
—When a tape recorded in LP mode with the
camcorder is played back on a Mini DV player or camcorder from another manu­facturer.
—When a tape recorded in LP mode is
played back on a Mini DV player or camcorder without an LP function.
• Audio dubbing is not possible with LP mode recordings.
4 Press f or d to select “LP”, then press
SET.
TAPE SPEED
33
LP
Selecting the 16-bit Audio Recording Mode
Available modes: TAPE-CAMERA, DUAL-
CAMERA
This camcorder allows you to select between the 12-bit and 16-bit audio recording modes. The camcorder normally records audio in the 12-bit audio recording mode. For higher-quality audio recording, select the 16-bit audio recording mode.
1 Set the camcorder to T APE-CAMERA or
DUAL-CAMERA mode (see page 29).
2 Press the MENU/DISPLAY button until
the menu screen appears.
3 Select U, then press SET. Select
AUDIO MODE (1), then press SET (2).
To return to 12-bit audio recording mode
Select 12bit” in step 4 above.
Note:
When using Audio Dubbing with 16-bit audio recordings, both the dubbed and original sounds will be recorded in mono (see page 67).
AUD I O SE T
as
1 1 2
SET
AUD I O MODE
ZOOM MI C
W
IND D IALOG REC RETURN
as
SET
1 2bit
1 6bit
4 Press f or d to select 16bit, then
press SET.
AUDIO MODE
16 bit
5 Press the MENU/DISPLAY button to
turn off the menu screen.
The 16-bit audio recording mode indicator appears.
16-bit audio recording mode indicator
AUTO
16 bit
Features
Useful
34
Useful Features
SRCH
Camera Recording
Digital Image Stabilization (DIS)
Available modes: TAPE-CAMERA, DUAL-
CAMERA, CARD-CAMERA
The digital image stabilization (DIS) function is factory preset to on to stabilize the image by electronically compensating for relatively minor image shaking that is often annoying in close­up shots.
DIS indicator
AUTO
60
min GAMMA
FADE
Note:
The DIS function cannot compensate for excessive image shaking.
Turning Off the DIS Function
Useful
Features
When image shaking does not occur (e.g.
SRCH
SRCH
when using the camcorder on a tripod), turn off the DIS function. The picture will appear more natural when the DIS function is off.
1 Set the camcorder to TAPE-CAMERA,
DUAL-CAMERA or CARD-CAMERA mode (see page 29).
2 Press the MENU/DISPLA Y button until
the menu screen appears.
3 Select T, then press SET. Select “DIS
(1), then press SET (2).
4 Press f or d to select OFF, then
press SET.
DIS
OFF
5 Press the MENU/DISPLAY button to
turn off the menu screen.
The z indicator is turned off.
To return to DIS mode
Select ON in step 4 above.
35
as
1 1 2
SET
MANU AL SE T
M
AN. FO CUS SHUT. SP EED EXPOSURE
PI C. EFFECT SCENE MENU
QK. RETURN
DIS RETURN
as
SET
ON
OFF
Setting the Digital Zoom
Available modes: TAPE-CAMERA, DUAL-
CAMERA, CARD-CAMERA
You can select from among three different zoom ranges in TAPE-CAMERA, DUAL­CAMERA and CARD-CAMERA modes: 1–10× (optical zoom), 10–40× (digital zoom), or 10– 200× (digital zoom). The digital zoom allows you to record powerful close-up pictures with the same operation as normal zooming.
Notes:
The digital zoom is in addition to the optical zoom giving a combined maximum zoom range of 1–200×.
As the image is enlarged digitally, the picture quality decreases when higher digital zoom settings are used.
1 Set the camcorder to TAPE-CAMERA,
DUAL-CAMERA or CARD-CAMERA mode (see page 29).
2 Press the MENU/DISPLA Y button until
the menu screen appears.
MANU AL SE T
M
AN. FO CUS SHUT. SP EED EXPOSURE
PI C. EFFECT SCENE MENU
QK. RETURN
DIS RETURN
as
SET
4 Press f or d to select 40 or 200 ,
then press SET.
DG TL ZOOM
002
5 Press the MENU/DISPLAY button to
turn off the menu screen.
The D digital zoom indicator is displayed during digital zooming.
12
15
Digital zoom indicator
D-
To use optical zoom only
Select OFF in step 4 above.
Features
Useful
3 Select Y, then press SET. Select
DGTL ZOOM (1), then press SET (2).
CAME RA SET
REC MODE
as
1 1 2
SET
PHOTO SNAP
EFF.SNAP DGTL Z OOM TAPE SPEED 16 9: RETURN
as
SET
OFF OFF
40 200
36
Useful Features
UT
min
min
GAMMA
FADE
GAMMA
FADE
SRCH
SRCH
min
GAMMA
FADE
SRCH
min
SRCH
UT
min
min
GAMMA
FADE
GAMMA
FADE
SRCH
SRCH
Camera Recording
Gamma Brightness Compen­sation
Note:
Note:
When the x indicator is displayed, the
When the x indicator is displayed, the
background will become slightly brighter.
background will become slightly brighter.
Available modes: TAPE-CAMERA, DUAL­CAMERA, CARD-CAMERA
When the subject is backlit or when recording in a dark or poorly illuminated location, the image will appear dark if it is recorded normally. The gamma brightness compensation function improves the picture by increasing the brightness of the image.
Recording a backlit subject
Press GAMMA once.
•“GAMMA turns yellow; indicating that Gamma Brightness Compensation is now working.
AUT
OAUTO
GAMMA
FADE
6
0
60
min
min
GAMMA
FADE
GAMMA
Useful
Features
FADE
AUTUTO
AUTO
SRCH
SRCH
To cancel Gamma Brightness Compensation
Press GAMMA until the x indicator disap­pears.
Recording in a poorly illuminated location
At locations where lighting is insufficient, LIGHT is displayed on the screen.
Press GAMMA once.
•“GAMMA turns yellow, indicating that the gain- up function is now working.
L I GHTLIGHT
SRCH
SRCH
L I GHTLIGHT
FADE
GAMMA
AUT
FADE
FADE
AUTO
AUTO
OAUTO
6
0
60
min
min
GAMMA
GAMMA
FADE
FADE
To obtain a brighter picture
Press GAMMA again.
The x indicator appears.
37
FADE
GAMMA
AUTUTOAUTO
FADE
FADE
6
6
60
60
0
0
0
min
min
min GAMMA
GAMMA
min
min
GAMMA
GAMMA
SRCH
SRCH
SRCH
SRCH
60
min
60
min
GAMMA
FADE
GAMMA
FADE
SRCH
SRCH
To obtain a brighter picture
Press GAMMA again.
The ` indicator appears.
AUTUTOAUTO
GAMMA
FADE
6
0
60
min
FADE
min
GAMMA
SRCH
SRCH
M
AN. FO CUS
EXPOSURE
SHUT. SP EED
PI C. EFFECT SCENE MENU QK. RETURN
START
STOP
MANU AL SE T
DIS RETURN
SET
as
To cancel the gain-up function
SRCH
Press GAMMA until the ` indicator disappears.
Notes:
Some picture noise appears in Gamma Brightness Compensation mode. The picture noise increases when the ` indicator is displayed.
When the ` indicator is displayed, a residual image may appear behind a subject that exhibits a lot of movement.
Fine brightness adjustment is possible using the manual exposure function (see page 61).
Quick Return
Available modes: TAPE-CAMERA, DUAL-
CAMERA
When you have been playing back what you have recorded on the tape, and wish to quickly return to recording from the end of the last recorded scene, use the quick return function.
1 Set the camcorder to T APE-CAMERA or
DUAL-CAMERA mode (see page 29).
2 Press the MENU/DISPLAY button until
the menu screen appears.
Edit Search
Available modes: TAPE-CAMERA, DUAL-
CAMERA
The edit search function lets you search, without switching to TAPE-VCR mode, for the point on the tape where you wish to start recording next.
1 Set the camcorder to TAPE-CAMERA or
DUAL-CAMERA mode (see page 29).
2 In Recording
Standby mode, press SRCH (SEARCH).
3 Press and hold down
er
e (forward edit
search) or r (reverse edit search).
4 When you find the point where you want
to begin recording, release the button.
5 Press SRCH to cancel the Edit Search
function.
Notes:
The sound is off during search.
Forward edit search is performed at the same
speed as normal playback, and reverse edit search at 6.5 times the normal playback speed.
Some picture noise appears during reverse edit search.
SRCH
SRCH
SRCHSRCH
3 Select T, then press SET. Select “QK.
RETURN (1), then press SET (2).
as
SET
1 1 2
4 Press f or d to select START, then
press SET.
•“SEARCH flashes, and the tape begins fast forwarding or rewinding to the end of the last recorded scene.
QK. RETURN
When the tape reaches the end of the last recorded scene, FINISHED” is displayed, and the camcorder enters Recording Standby mode.
SEARCH
5 Press the MENU/DISPLAY button to
turn off the menu screen.
Notes:
To cancel the quick return function, press SET to select STOP, then press SET.
If the cassette has been removed since the last recording or if no recording has been made since the cassette was loaded, the quick return function cannot be used.
38
Features
Useful
Useful Features
SRCH SRCH
NORMAL
CARD 2/98
CARD
AUTO
60
min
Q
GAMMA
FADE
SRCH
Camera Recording
Dual Recording
Available mode: DUAL-CAMERA
By setting the camcorder to DUAL-CAMERA mode, you can automatically record motion images on a tape and still images on a card without operating the Media Selection switch.
STILL button
REC START/STOP button
1 Make sure that a Mini DV cassette and a
card are inserted in the camcorder.
2 Set the Media Selection
switch to DUAL.
Useful
Features
3 Hold down the Lock button and set the
POWER switch to CAMERA.
The camcorder turns on in DUAL­CAMERA mode.
The camcorder is now ready to record (Recording Standby mode).
Number of shots remaining
Number of shots taken
AUTO
2/98
NORMAL
4 Press the REC START/STOP button to
begin recording motion images of the subject on a tape.
Operate the camcorder just as you ordinarily would when recording in TAPE-CAMERA mode.
AUTO
min
60
GAMMA
FADE
SRCH
SRCH
Press the STILL button to record a still image of the subject on a card.
The O indicator flashes red while the image is being recorded on the card.
Notes:
If you press the STILL button while recording motion images on a tape in DUAL-CAMERA mode, a still image of the subject is recorded on the tape for 1.5 seconds as well as on a card (the Q indicator is recorded on the tape along with the still image).
See page 78 for playing back still images recorded on a card.
REC
2/98
NORMAL
Lock button
39
60
min GAMMA
FADE
Resolution setting indicator
Note: You can select the desired picture quality for still images recorded on a card (see page 73).
SRCH
SRCH
Still Recording on Tape
Available mode: TAPE-CAMERA
You can record still images of subjects with normal sound on a tape by selecting one of two still recording modes.
Still Recording mode options
SNAP: A still picture is recorded for 6 seconds. STILL: A continuous still image is recorded.
7 Press the MENU/DISPLAY button to
turn off the menu screen.
Using Still Recording
STILL button
REC START/STOP button
Selecting Still Recording Mode
1 Set the camcorder to T APE-CAMERA
mode (see page 29).
2 Press the MENU/DISPLA Y button until
the menu screen appears.
3 Select Y, then press SET. Select
“SNAP EFF.” (1), then press SET (2).
CAME RA SET
REC MODE
as
1 1 2
SET
PHOTO SNAP
EFF.SNAP DGTL Z OOM TAPE SPEED 16 9: RETURN
as
SET
OF F
PHOTO
FRAMES
9 16
SHOT
FRAMES
4 Press f or d to select OFF, then
press SET.
OFFEFF.SNAP
5 Press f or d (1) to select PHOTO
SNAP, then press SET (2).
CAME RA SET
REC MODE
as
1 1 2
SET
PHOTO SNAP SNAP
EFF.SNAP
DGTL Z OOM
TAPE SPEED 16 9: RETURN
as
ST I LL
SET
6 Press f or d to select the desired still
recording mode, then press SET.
1 Set the camcorder to T APE-CAMERA
mode.
2 In Recording Standby mode,
press the STILL button.
A still image of the subject is displayed.
3 Press the REC START/STOP
button.
The still image is recorded.
In SNAP mode, the camcorder returns to Recording Standby mode after recording a still image for 6 seconds.
To pause recording
Press the REC START/STOP button.
To cancel the still image
In SNAP mode, press the STILL button while
the camcorder is in Recording Standby mode.
In STILL mode, press the STILL button.
Notes:
Still Recording can also be used during recording by pressing the STILL button.
If you use SNAP during recording, a still picture is recorded for 6 seconds, and then the camcorder enters Recording Standby mode.
The picture quality in Still Recording mode will be slightly lower than normal pictures.
Features
Useful
PHOTO SNAP ST ILL
40
Useful Features Camera Recording
Still Recording Effects
Available modes: TAPE-CAMERA, CARD-
CAMERA
You can select one of these still recording effects to record the still images with an effect.
Type of Still Recording Effects
PHOTO SHOT: A still picture is recorded
following the sound and visual effects of a camera shutter closing.
9 FRAMES: A still picture is recorded at
intervals of 1/8 of a second using a 9-frame picture.
16 FRAMES: A still picture is recorded at
intervals of 1/8 of a second using a 16-frame picture.
Selecting a still recording effect
1 Set the camcorder to TAPE-CAMERA or
CARD-CAMERA mode (see page 29).
2 Press the MENU/DISPLA Y button until
the menu screen appears.
Useful
Features
3 Select Y, then press SET.
Note:
In TAPE-CAMERA mode, select the desired still recording mode (see page
40).
4 Press f or d (1) to select SNAP
EFF., then press SET (2).
CAME RA SET
REC MODE
as
1 1 2
SET
PHOTO SNAP
EFF.SNAP DGTL Z OOM TAPE SPEED 16 9: RETURN
OF F
PHOTO
9 16
SHOT
FRAMES
FRAMES
Using PHOTO SHOT, 9 FRAMES or 16 FRAMES mode
1 Perform the steps in Selecting a still
recording effect to select “PHOTO SHOT, 9 FRAMES or 16 FRAMES.
2 In Recording Standby mode,
press the STILL button.
In TAPE-CAMERA mode, a still image of the subject is displayed with the selected effect. Perform step 3.
In CARD-CAMERA mode, the still image of the subject will be recorded with the selected effect. Omit step 3.
3 Press the REC ST ART/ST OP
button.
The still image of the subject will be recorded on tape.
T o cancel the still image in TAPE­CAMERA mode
In SNAP mode, press the STILL button while
the camcorder is in Recording Standby mode.
In STILL mode, press the STILL button.
Notes:
Still recording effects can also be used during recording on tape by pressing the STILL button.
If you use PHOTO SHOT while recording on tape, the visual effects of a camera shutter closing will not work.
You can use PHOTO SHOT without the sound effect of a camera shutter closing by setting the SOUND menu item to “OFF” (see page 89).
The picture quality in Still Recording Effects mode will be slightly lower than normal pictures.
as
SET
5 Press f or d to select the desired still
recording effect, then press SET.
EFF.SNAP
PHOTO SHOT
6 Press the MENU/DISPLA Y button to
turn off the menu screen.
41
Digital Picture Effects
Available modes: TAPE-CAMERA, DUAL-
CAMERA, CARD-CAMERA
These digital picture effects let you record the subject with a more dramatic effect.
Digital picture effect options
B/W: To record in black-and-white. SEPIA: To record in sepia colour similar to that
of an old photograph.
MOSAIC: To record a picture divided up into
tiles.
SOLARI: To record with enhanced contrast,
creating a unique artistic image.
NEGA: To record a picture whose blacks and
whites of the image are reversed and colours of the image are inverted.
1 Hold down the Lock button and set the
POWER switch to CAMERA or VCR.
2 Press the MENU/DISPLA Y button until
the menu screen appears.
MANU AL SE T
M
AN. FO CUS SHUT. SP EED EXPOSURE
PI C. EFFECT SCENE MENU
QK. RETURN
DIS RETURN
as
SET
4 Press f or d to select the desired
digital picture effect, then press SET.
The selected digital picture effect is displayed on the menu screen.
PIC. EFFECT
BW
5 Press the MENU/DISPLAY button to
turn off the menu screen.
To cancel the digital picture effect
Select OFF in step 4 above.
Note:
Digital picture effects cannot be used when a still image is displayed.
Features
Useful
3 Select T, then press SET. Select “PIC.
EFFECT (1), then press SET (2).
MANU AL SE T
M
AN. FO CUS
as
1 1 2
SET
SHUT. SP EED EXPOSURE
PI C. EFFECT SCENE MENU
QK. RETURN
DIS RETURN
as
SET
OFF
BW SEP I A M
OSA I C SOL AR I NEGA
42
Useful Features
bit
AUTO
min
GAMMA
FADE
SRCH
bit
AUTO
min
GAMMA
FADE
SRCH
bit
AUTO
min
GAMMA
FADE
SRCH
Camera Recording
Fade In and Fade Out
Available modes: TAPE-CAMERA, DUAL-
CAMERA
The fade function allows you to gradually bring the image and sound in or out at the beginning or end of a scene for creating scene transi­tions. This is especially effective for indicating a dramatic change in scenery.
Fade in
Fade out
Setting Fade Mode
1 Set the camcorder to TAPE-CAMERA or
DUAL-CAMERA mode (see page 29).
2 In Recording Standby mode, press
FADE.
Useful
Features
AUTO
AUTO
12bit
12 bit
Using Fade Mode
1 Press the REC START/STOP button to
begin recording.
The picture turns white, and the image and sound fade in.
AUTO
AUTO
12bit
12 bit
33
min
0
min
0
GAMMA
FADE
FADE
GAMMA
SRCH
SRCH
2 Press the REC STAR T/STOP button at
the point where you wish to stop recording.
The image and sound fade out as the picture gradually turns white. The camcorder then returns to Recording Standby mode.
AUTO
AUTO
12bit
12 bit
33
min
0
min
0
GAMMA
FADE
FADE
GAMMA
SRCH
SRCH
43
FADE
FADE
33
0
0
min
min
GAMMA
GAMMA
SRCH
SRCH
T o cancel Fade mode
Press FADE again.
T o use Fade Out only
1 During camera recording in T APE-
CAMERA mode, press FADE.
2 Press the REC STAR T/STOP button at
the point where you wish to stop recording.
Note:
Fade mode is automatically canceled after Fade Out.
Wide Screen (16:9)
Macro Shots
Available mode: TAPE-CAMERA
The wide screen function lets you record scenes with the wide-screen feel of a movie shown in a theatre. The top and bottom of the picture are masked with black bands to produce an effective screen aspect ratio of 16:9.
Normal screen Wide screen
1 Set the camcorder to T APE-CAMERA
mode (see page 29).
2 Press the MENU/DISPLAY button until
the menu screen appears.
3 Select Y, then press SET. Select “16:9
(1), then press SET (2).
CAME RA SET
REC MODE
as
1 1 2
SET
PHOTO SNAP
EFF.SNAP DGTL Z OOM TAPE SPEED 16 9: RETURN
as
SET
OFF
ON
4 Press f or d to select ON, then press
SET.
16 9:
ON
Available modes: TAPE-CAMERA, DUAL­CAMERA, CARD-CAMERA
This camcorder lets you shoot close-up images of small objects such as flowers and insects, or make title frames for your videos. When you want to record a magnified image of a subject which is within approximately 1.5 m of the camcorder, do not zoom in on it. Instead, zoom out all the way by pressing the Power Zoom W button, and then move the camcorder closer to the subject until you obtain the desired angle of view. The camcorder will automatically focus on the subject when the lens is set for the widest angle.
Tripod
Notes:
When you are recording a macro shot, be sure that the subject receives sufficient illumination.
It is recommended that you use a tripod for recording macro shots, to prevent image shaking.
Power Zoom W button
Features
Useful
5 Press the MENU/DISPLAY button to
turn off the menu screen.
The picture is displayed with the top and bottom portions masked.
To return to normal screen
Select OFF in step 4 above.
44
Useful Features Camera Recording
Letting the Subject Monitor the Shot
Available modes: TAPE-CAMERA, DUAL-
CAMERA, CARD-CAMERA
Open the LCD monitor and rotate it 180° vertically so that the screen faces the other way and the subject can monitor the shot while you are recording with the viewfinder.
If the camcorder is steadied, you can record yourself in the scene by watching yourself on the LCD monitor. The supplied infrared remote control is useful for such occasions.
Useful
Features
1 Pull out the viewfinder completely . Open
the LCD monitor to a 90° angle to the camcorder body (1), and then rotate it 180° vertically (2).
180
2
90
1
3 Set the POWER switch to CAMERA.
The subject is displayed in the viewfinder, and a mirror image of the subject is displayed on the LCD monitor.
4 Press the REC STAR T/STOP button to
begin recording.
Caution:
Do not invert the image by rotating the LCD monitor during recording.
Notes:
The screen image is automatically inverted when the vertical rotation of the LCD monitor is between 135° and 180°. When the monitor is rotated back to within 135°, the image returns to normal.
If the indicator flashes when the LCD monitor is in the inverted position, this indicates a warning. To check the type of warning, rotate the monitor back to within 135°. (See pages 9 and 10 for descriptions of the warning indicators.)
Auto Focus
Available modes: TAPE-CAMERA, DUAL-
CAMERA, CARD-CAMERA
The camcorder is preset to Auto Focus mode, which is designed to focus on most types of subjects. In Auto Focus mode, the camcorder automatically focuses on whatever is in the centre of the scene. Always keep the subject in the centre of the scene.
2 Set the Media Selection switch to T APE,
DUAL, or CARD.
45
Notes:
If no subject is in the centre of the scene, the focus area will expand and the subject nearest the centre will be focused on.
If no subject is displayed, the camcorder will automatically zoom out until a subject comes into the frame.
Auto Focus may not work in the situations described on page 55. In these situations, use the manual focus function.
Useful Features
Playback
Using the Infrared Remote Control
Available modes: all modes
Use the supplied infrared remote control to operate the camcorder from a distance, such as when you want to record yourself in a scene, or when the camcorder is connected to a TV for use as a VCR.
Installing the Batteries in the Remote Control
1 Open the battery compartment cover.
2 Insert the two supplied AA (R6 or UM/
SUM-3) batteries with the battery poles positioned as indicated.
Turning on the Infrared Remote Control Mode
Available modes: TAPE-VCR, CARD-VCR
1 Set the camcorder to TAPE-VCR or
CARD-VCR mode (see page 29).
2 Press the MENU/DISPLA Y button until
the menu screen appears.
3 Select I, then press SET. Select
“REMOTE” (1), then press SET (2).
as
1 1 2
OTHERS
REMOTE
SET
SOUND TIME CODE TC OUT RETURN
as
SET
ON
OFF
4 Press f or d to select “ON”, then press
SET.
REMOT E
ON
5 Press the MENU/DISPLAY button to
turn off the menu screen.
Features
Useful
3 Replace the cover.
1
Note:
• When the batteries are depleted and the remote control does not operate, replace them with new AA (R6 or UM/SUM-3) batteries.
Caution:
• Do not use old and new batteries or batteries of different brands together.
2
46
Useful Features Playback
Control Buttons on the Infrared Remote Control
TAPE REC START/STOP
button [pp. 23, 39]
CARD REC button [pp. 39, 72]
REW button [pp. 26, 27]
PAUSE/STILL button [p. 27]
STOP button [p. 26]
Playback Direction buttons
[p. 48]
Operating the Infrared Remote Control
1 Open the LCD monitor to a 90° angle to
Useful
the camcorder body (1), and then
Features
rotate it 180° vertically (2).
180
2
90
ZOOM T/W buttons [pp. 24, 54]
VOL. =/- buttons [p. 27]
PLAY button [p. 26]
FF button [pp. 26, 27]
SLOW button [p. 48]
Shift buttons [p. 53]
4 Aim the remote control transmitter at the
infrared remote sensor of the camcorder, and press the control buttons for operation.
Approximate operating range of remote control
1
2 Set the Media Selection switch on the
camcorder to T APE, DUAL, or CARD.
3 Set the POWER switch on the camcorder
to CAMERA or VCR.
47
5 m
Infrared remote sensor
Transmitter
Notes:
Be careful not to allow direct sunlight or bright light from interior illumination to fall onto the remote sensor, as this may prevent the remote control from operating properly.
Be sure that there are no obstacles between the remote control and the remote sensor.
Tape Playback Functions with the Infrared Remote Control
Available mode: TAPE-VCR
These tape playback functions can be operated using the supplied infrared remote control. (See pages 46 and 47 for use of the infrared remote control.)
PAUSE/STILL button
PLAY button
Note:
To protect the tape, the camcorder automatically returns to normal playback if it is left in Slow mode for more than 10 minutes.
Frame Advance
The frame advance function allows you to play back still images frame by frame.
1 During tape playback, press the PAUSE/
STILL button (n) to pause playback.
SLOW button
Playback Direction buttons
Reverse Playback
The reverse playback function allows you to play back video in reverse.
During tape playback, press the Playback Direction m button.
To return to normal playback, press the PLAY button (s).
Slow
The slow function allows you to play back images in slow motion.
During tape playback, press the SLOW button (/).
2 Press the Playback Direction , (or
m) button.
Each time you press the button, the picture advances one frame forward (or backward).
To return to normal playback, press the PLAY button (s).
Notes:
The sound is off during reverse, slow, and frame advance playback.
If you use the slow or frame advance function with the tape recorded in LP mode, the picture may advance several frames at a time.
Features
Useful
To return to normal playback, press the PLAY button (s).
48
Useful Features Playback
Displaying the Date and Time of Recording
Available modes: all modes
Follow the procedure below to display the date, or both the date and time, of recording on the screen. You can display the date and time during both recording and playback.
1 Hold down the Lock button and set the
POWER switch to CAMERA or VCR.
2 Press the MENU/DISPLA Y button until
the menu screen appears.
3 Select P, then press SET. Select
“DISPLAY” (1), then press SET ( 2).
Useful
Features
as
1 1 2
SET
CLOCK SE T
DISPLAY
AREA SUMR TIME SET T I NG 12H 24H
RETURN
as
OFF
DAT E DAT E+TIME
SET
4 Press f or d to select DATE or
DATEHTIME”, and then press SET.
DISPLAY
DAT E+TIME
Using Earphones (Commer­cially Available)
Available modes: TAPE-VCR, TAPE-CAMERA,
DUAL-CAMERA
You can monitor the sound via stereo ear­phones (commercially available) during playback or recording. Stereo earphones with a
3.5 mm diameter plug can be connected to the
camcorder by using the supplied earphones connecting cable.
Open the jack cover, and connect stereo earphones to the camcorder as shown in the figure.
PHONES jack
To PHONES jack
Earphones connecting cable (supplied)
5 Press the MENU/DISPLA Y button to
turn off the menu screen.
The date (or the date and time) is displayed.
50
min
GAMMA
FADE
Notes:
Before recording, make sure that the date and time have been correctly set (see pages 18 and
19). If they have not been set, the display will be left blank (“–”) when playing back the recording. (The display will also be left blank for unre­corded or damaged portions of the tape.)
In TAPE-VCR mode, the current date and time are displayed when the tape is not being played back.
49
2.
SRCH
Notes:
Before connecting stereo earphones, turn the camcorder volume down to the lowest setting.
The built-in speaker automatically turns off when stereo earphones are connected to the PHONES jack.
When recording, you cannot adjust the volume
2002.6
03:01
with the Power Zoom/VOL. buttons on the camcorder. Use the VOL. buttons on the infrared remote control instead.
Using the Time Code
e
y
r
d
GAMMAGAMMA
e
y
r
d
GAMMA
Available modes: TAPE-VCR, TAPE-CAMERA, DUAL-CAMERA
The time code shows the hour, minute and second of recording, and the frame number (1 frame = approx. 1/25 sec.). This is automati­cally recorded along with the subject when you are recording on the tape. You can display the time code on the screen to check the elapsed time when playing back from tape or recording on tape.
Display format
0 00 10 20TC
Frame number*
Second
Minute
Hour
*Displayed during still
or frame advance playback.
1 In TAPE-VCR, T APE-CAMERA, or
DUAL-CAMERA mode, press the MENU/DISPLAY button until the menu screen appears.
2 Select I, then press SET. Select “TIME
CODE (1), then press SET (2).
4 Press the MENU/DISPLAY button to
turn off the menu screen.
The time code appears.
Time code
TCO 0 5:35:
To turn off the time code
Select DISP. OFF in step 3 above.
Note:
When the tape reaches an unrecorded section, the time code returns to “TC-:--:--”. Once recorded, the time code cannot be changed.
Displaying the time code on a TV during playback
1 In T APE-VCR mode, select I, then
press SET. Select TC OUT” (1), then press SET (2).
OTHERS
REMOTE
as
1 1 2
SET
SOUND
TIME CODE TC OUT RETURN
OFF
ON
Features
Useful
OTHERS
REMOTE
as
1 1 2
SET
SOUND TIME CODE TC OUT RETURN
as
SET
3 Press f or d to select DISP. ON, then
press SET.
TIME CODE
DISP.ON
DISP. OFF
DISP. ON
as
SET
2 Press f or d to select ON, then press
SET.
TC OUT
ON
3 Press the MENU/DISPLAY button to
turn off the menu screen.
50
Useful Features Playback
Playback Effects
Available mode: TAPE-VCR
Playback effects can be used to create an interesting scene transition between a still image and the following image during playback.
T ype of Playback Effects
OVERLAP: A still image fades out as the next
image fades in, replacing the previous image. The two scenes momentarily dissolve.
WIPE: A still image is replaced with the next
Useful
image first appearing in the middle of the
Features
screen and gradually expanding to fill the screen.
Using Playback Effect
1 In TAPE-VCR mode, press the MENU/
DISPLA Y button until the menu screen appears.
2 Select V, then press SET. Select “PB
EFFECT (1), then press SET (2).
PLAYBACK SE T
AUDI O DUB
as
1 1 2
SET
AUDI O
EFFECT
PIC.
PB EFFECT
M
ULTI FRAME
RETURN
as
SET
OFF
OVE RLAP
W
IPE
3 Press f or d to select OVERLAP or
WIPE, then press SET.
PB EFFECT
W
IPE
4 Press the MENU/DISPLA Y button to
turn off the menu screen.
5 Rewind or fast forward the tape to just
before the position where you want to use the playback effect, and then begin playback.
The still image is replaced with the next image with the selected playback effect.
Preparation
Plan the scene transition, and record still images with the still recording function (see page 40).
Notes:
Playback effects can also be used to provide a transition from a still image to a moving image.
Record images for 6 seconds or longer. An image recorded for less than 6 seconds may not dissolve properly.
51
T o cancel the playback effect
Select OFF in step 3 above.
Notes:
Playback effects will be canceled if Multiple Strobe Playback, Picture Effect Playback or Playback Zoom is used thereafter.
Playback effects will be canceled if the power source is interrupted.
Picture Effect Playback
Available modes: TAPE-VCR, CARD-VCR
These picture effects let you play back images with a more dramatic effect.
Picture effect options
B/W: The picture is displayed in black-and-
white.
SEPIA: The picture is displayed in sepia colour
similar to that of an old photograph.
MOSAIC*: The picture is divided up into tiles. SOLARI: The contrast of the subject is
enhanced, creating a unique artistic image.
NEGA: The blacks and whites of the image are
reversed and colours of the image are inverted.
*Available only in TAPE-VCR mode.
1 During playback in TAPE-VCR or CARD-
VCR mode, press the MENU/DISPLA Y button until the menu screen appears.
2 Select V, then press SET. Select “PIC.
EFFECT (1), then press SET (2).
PLAYBACK SE T
AUDI O DUB
as
1 1 2
SET
AUDI O
EFFECT
PIC. PB EFFECT M
ULTI FRAME
RETURN
as
SET
OFF
BW SEP I A M
OSA IC SOL AR I NEGA
To cancel Picture Effect Playback
Select OFF in step 3 above.
Notes:
Images in Picture Effect Playback mode cannot be transferred via DV or PC connecting cable to a personal computer.
Picture Effect Playback cannot be used with Multiple Strobe Playback, Playback Effects or Slide Show Playback.
Features
Useful
3 Press f or d to select the desired
picture effect, then press SET.
P I C. EFFECT
BW
4 Press the MENU/DISPLA Y button to
turn off the menu screen.
52
Useful Features
DIO
GAMMA
DIO
GAMMA
Playback
Playback Zoom
Available modes: TAPE-VCR, CARD-VCR
The playback zoom function allows you to magnify the playback picture up to 10 times its original size and to shift the magnified picture by using the remote control (see pages 46 and 47 for use of the remote control.).
ZOOM buttons
Shift buttons
The example screens for this feature are for TAPE-VCR mode.
1 During playback in T APE-VCR or CARD-
VCR mode, press the ZOOM T button to
Features
zoom in.
Playback zoom indicator
Useful
AUDIO
AUDIO
+
+
1 2
12
To cancel Playback Zoom
Press the ZOOM W button to zoom out to the widest angle.
Notes:
Use of Playback Zoom may cause a reduction in picture quality for still images.
Images in Playback Zoom mode cannot be transferred via DV or PC connect cable to a personal computer.
y
y
e
e
r
r
d
d
2 Press the Shift q, w, a, or s button to
shift the displayed image.
AUDIO
AUDIO
53
e
e
y
y
r
r
d
d
GAMMA
GAMMA
+
1 2
2+1
GAMMA
GAMMA
Gamma Playback
DIO
GAMMA
DIO
GAMMA
OFF
FRAMES
FRAME S
16
9
AUDI O DUB PIC.
EFFECT
AUDI O PB EFFECT
M
ULTI FRAME
PLAYBACK SE T
RETURN
SET
as
Multiple Strobe Playback
Available mode: TAPE-VCR
The gamma playback function improves the tape playback picture by increasing the brightness of the subject while leaving the brighter portions of the image unaffected.
During playback in TAPE-VCR mode, press GAMMA once.
•“GAMMA1 appears, and the picture becomes brighter.
GAMMA1GAMMA1
AUDIO
1 2
AUDIO
12
d
GAMMA
y
y
e
e
r
r
d
d
GAMMA
GAMMA
To obtain a brighter picture, press GAMMA again.
•“GAMMA2 appears.
GAMMA22GAMMA
AUDIO
1 2
AUDIO
d
d
12
GAMMA
GAMMA
d
GAMMA
e
e
y
y
r
r
T o cancel Gamma Playback
Press GAMMA button until GAMMA1 andGAMMA2 disappear.
Note:
Gamma Playback has no effect during still playback.
Available mode: TAPE-VCR
The multiple strobe playback function can be used to capture the action of a fast-moving subject at intervals of 1/8 of a second using a 9- or 16-frame picture. This is useful when you want to check your form in sports such as tennis or golf.
1 In TAPE-VCR mode, press the MENU/
DISPLAY button until the menu screen appears.
+
+
2 Select V, then press SET. Select
MULTI FRAME (1), then press SET (2).
as
SET
1 1 2
+
+
2
3 Press f or d to select 9 FRAMES
Features
Useful
(9-frame picture) or 16 FRAMES (16­frame picture), then press SET.
M
ULTI FRAME
16
FRAMES
4 Press the MENU/DISPLAY button to
turn off the menu screen, and then begin playback.
5 Press the STILL button at the
point where you want to begin the multiple strobe playback.
A multi-frame picture of the image is displayed.
To cancel Multiple Strobe Playback
Press the STILL button again.
Note:
Multiple Strobe Playback cannot be used during video search, still or slow playback.
54
Advanced Features
min
Advanced Features
Camera Recording
Camera Recording
Manual Focus
Available modes: TAPE-CAMERA, DUAL-
CAMERA, CARD-CAMERA
Auto Focus may not be able to focus on the subject in the situations shown below. In such situations, set the camcorder to Manual Focus mode and focus manually.
Subject is too dark.
Fast-moving subject. Background is too bright.
Subject has horizontal stripes.
Light reflects off the subject.
Features
Advanced
Subject has fine, repeated
patterns.
Fast-speed shutter being
used under fluorescent
lighting.
Lack of contrast, e.g.
snow scene.
Subject is being shot through
a dirty or wet window.
Two subjects at different distances
overlap in the same scene.
Subjects at different distances
appear in the centre of the scene
at the same time.
Power Zoom buttons
EASY/MANUAL/AUTO Selection switch
1 Set the camcorder to TAPE-CAMERA,
DUAL-CAMERA, or CARD-CAMERA mode.
2 In Recording Standby
mode, set the EASY/ MANUAL/AUTO Selection switch to MANUAL.
3 Press the MENU/DISPLAY button until
the menu screen appears.
4 Select T, then press SET. Select “MAN.
FOCUS” (1), then press SET (2).
MANU AL SE T
M
as
1 1 2
SET
AN. FO CUS AUT O SHUT. SP EED EXPOSURE PI C. EFFECT SCENE MENU QK. RETURN DIS RETURN
as
SET
M
ANUAL
5 Press a or s to select “MANUAL”, then
press SET.
• The focus setting screen is displayed.
MANUAL
MF
55
FOCUS
FADE
0
0
33
min
min
GAMMA
SRCH
6 Turn the CONTROL dial up or down (1)
min
min
SP
min
to focus on the subject, then press the CONTROL dial (2).
Turning the CONTROL dial up ( ): To focus far
Turning the CONTROL dial down ( ): To focus near
8 Press the MENU/DISPLAY button to
turn off the menu screen.
•“MF is displayed.
Manual focus indicator
MANUAL MF
MANUAL
1
MF
FOCUS
2
33
min
0
min
0
GAMMA
FADE
MANUAL MF
FOCUS
AUTO
SET
min
0
min
0
33
GAMMA
FADE
SP
SRCH
SRCH
7 Press the CONTROL dial to lock the
focus.
MANU AL SE T
M
AN. FO CUSMANUAL
SHUT. SP EED EXPOSURE PI C. EFFECT SCENE MENU
QK. RETURN
DIS RETURN
as
SET
33
min
0
min
0
SP
GAMMA
FADE
SRCH
To cancel Manual Focus mode
After performing step 4 above, select AUTO”, then press SET.
Notes:
The camcorder may not be able to focus correctly if the subject is within approximately
1.5 m. Set the zoom control to wide angle, and then try refocusing.
If the lens is dirty or fogged, the camcorder may not be able to correctly focus.
When MF is displayed, you can manually adjust the focus by turning the CONTROL dial up or down, even if the focus setting screen is not displayed.
Advanced
Features
56
Advanced Features
M
AN. FO CUS
EXPOSURE
SHUT. SP EED PI C. EFFECT
SCENE MENU QK. RETURN DIS
MANU AL SE T
AUTO
M
ANUAL
RETURN
SET
as
Camera Recording
Setting the Shutter Speed
Available modes: TAPE-CAMERA, DUAL-
CAMERA, CARD-CAMERA
The shutter speed of the camcorder is preset to auto mode, which automatically chooses the optimal shutter speed for the ambient light. However, depending on the subject or situation, you may want to set the shutter speed manually to create a high-quality picture.
Recommended Shutter Speeds
The faster the shutter speed, the darker the picture becomes. Select the most appropriate shutter speed for the ambient light.
Situation
Recording sports action in bright daylight.
Recording in bright daylight at a ski resort.
Recording outdoor sports on a partially cloudy day.
Recording an outside scene through a car window (when you want to minimize blur caused by the camera shaking).
Recommended
shutter speed
1/10,000 sec.
l
1/1,000 sec.
1/1,000 sec.
l
1/250 sec.
EASY/MANUAL/AUTO Selection switch
1 Set the camcorder to TAPE-CAMERA,
DUAL-CAMERA, or CARD-CAMERA mode.
2 Set the EASY/
MANUAL/AUTO Selection switch to MANUAL.
3 Press the MENU/DISPLAY button until
the menu screen appears.
4 Select T, then press SET. Select
SHUT. SPEED” (1), then press SET (2).
as
SET
1 1 2
When you want to reduce
Features
Advanced
the light by half. Use as a substitute for an ND2 filter.
Tips on Using the Manual Shutter Speed
Fast shutter speeds can be used with the still recording function (see pages 39 to 41 and
72) to record higher quality still images of fast-moving subjects.
If the on-screen picture flickers when recording under fluorescent lighting, you may be able to compensate by setting the shutter speed to 1/120 sec.
57
1/120 sec.
5 Press a or s to select MANUAL, then
press SET.
The shutter speed setting screen is displayed.
MANUAL
SHUT.
FADE
+
-
SPEED
GAMMA
00001 AUTO AUTO
SRCH
6 Turn the CONTROL dial up or down to
select the desired shutter speed.
• The number shown is the selected shutter speed level. The adjustment range is from 1/50 sec (slowest) to 1/ 10,000 sec (fastest).
MANU AL
SHUT.
+
-
FADE
MANU AL
SPEED
GAMMA
00001
AUTO
AUTO
SRCH
8 Press the MENU/DISPLAY button to
turn off the menu screen.
To return to Auto Shutter Speed mode
After performing step 4 above, select “AUTO”, then press SET.
Notes:
• Recording with a shutter speed faster than 1/50 sec. tends to darken the picture. Record in bright locations when you use a fast shutter speed.
• Using a fast shutter speed under fluorescent lighting will cause flickering in the picture and possibly periodic color shifts.
The manual shutter speed setting will be
canceled if a scene setting is selected thereafter.
SPEED
SHUT.
+
-
GAMMA
FADE
Shutter speed
indicator
10000 4000 2000 1000 500 250 120 50 AUTO
SRCH
Shutter speed
1/10,000 sec.
1/4,000 sec. 1/2,000 sec. 1/1,000 sec.
1/500 sec. 1/250 sec. 1/120 sec.
1/50 sec.
Variable
7 Press the CONTROL dial to set the
shutter speed.
• The selected shutter speed level is displayed on the menu screen.
MANU AL S ET
M
AN. FOCUS
SHUT. S PEE D
EXPOSURE PI C. EFFECT SCENE MENU QK. RETURN DIS RETURN
as
2000
SET
00001
0020
AUTO
Advanced
Features
58
Advanced Features
GAMMA
FADE
SRCH
Camera Recording
Scene Menu (Programme AE)
Available modes: TAPE-CAMERA, DUAL-
CAMERA, CARD-CAMERA
You can set the camcorder to the shooting mode that will create the best results for a specific situation by just selecting one of the scene settings shown below.
Scene setting options
Scene setting
Features
Advanced
SPORT
SUNLIGHT
DUSK
PARTY
You can record a fast-moving subject with little blurriness. (The shutter speed is set to 1/500 sec.) This is effective for recording tennis swings, track and field events, and so on.
You can record without darkening the subject even if the background is particularly bright. This is effective for recording at ski areas or when swimming in the ocean.
You can accurately record the red of the setting sun and the surrounding twilight.
You can record a picture with the brightness adjusted for a subject with a large contrast to minimize white flaring. This is effective for recording subjects illuminated by a spotlight.
Effect
1 Set the camcorder to T APE-CAMERA,
DUAL-CAMERA, or CARD-CAMERA mode.
3 Select T, then press SET. Select
SCENE MENU (1), then press SET (2).
MANU AL SE T
M
AN. FO CUS
as
1 1 2
SET
SHUT. SP EED EXPOSURE
PI C. EFFECT SCENE MENU
QK. RETURN
DIS RETURN
as
SET
OFF
SPORT SUNL I GH T DUSK PARTY
4 Press f or d to select the scene
setting that best fits the recording situation, then press SET.
The selected scene setting is displayed on the menu screen.
SCENE MENU
SPORT
5 Press the MENU/DISPLA Y button to
turn off the menu screen.
The selected scene setting indicator is displayed.
Scene setting indicator
SPORT
30
min
To cancel the scene setting
Select OFF in step 4 above.
2 Press the MENU/DISPLAY button until
the menu screen appears.
MANU AL SE T
M
AN. FO CUS SHUT. SP EED EXPOSURE
PI C. EFFECT SCENE MENU
QK. RETURN
DIS RETURN
as
59
SET
Adjusting the White Balance
Available modes: TAPE-CAMERA, DUAL-
CAMERA, CARD-CAMERA
The colour of the subject on the screen tends to look different depending on the lighting condition. The camcorder is preset to Auto White Balance mode, which automatically adjusts the hue of the picture for the current lighting condition.
Auto White Balance may not work properly for the following subjects. In this case, use the white balance lock function.
Subjects with one dominant colour or subjects against background with one dominant colour
Subjects under very bright light source, e.g. video lights
Subjects under light source with red hue, e.g. glow of sunset
Close-up images of small objects
W/B button
1 Set the camcorder to TAPE-CAMERA,
DUAL-CAMERA or CARD-CAMERA mode.
2 In Recording Standby
mode, set the EASY/ MANUAL/AUTO Selection switch to MANUAL.
3 Aim the lens at a white object.
Adjust the distance of the object so that the entire screen is white.
4 Press the W/B button to set the white
balance lock.
•“WHITE BAL” flashes and then changes toW/B LOCK. To cancel the locking
procedure, press the W/B button while WHITE BAL flashes.
MANUAL
WHITE BAL
MANUAL WB
LOCK
30
min
GAMMA
FADE
To cancel White Balance Lock
Press the W/B button.
•“W/B LOCK disappears and the white balance lock is cancelled.
Notes:
If the light source changes or if you move from indoors to outdoors, or vice versa, when recording with the white balance locked, the white balance may shift. Reset the white balance.
Do not move the camcorder while WHITE BAL is flashing in step 4.
If WHITE BAL does not stop flashing in step 4, return to Auto mode to cancel the locking procedure, and repeat from step 2.
White Balance Lock will be canceled if a scene setting is selected thereafter.
SRCH
Advanced
Features
60
Advanced Features
MANUAL
EXPOSURE
+
-
+5 +
3
-
5
GAMMA
FADE
SRCH
Camera Recording
Manual Exposure
Available modes: TAPE-CAMERA, DUAL-
CAMERA, CARD-CAMERA
The camcorder is preset to Auto Exposure mode, which automatically chooses the optimal aperture. When there is too much contrast in brightness between the subject and back­ground, however, you may not be able to record a clear image. In this case, use the manual exposure function to correct the exposure level.
Background is too bright and subject too dark (backlit subject).
Increase the exposure level to allow more light through the lens.
Subject is too bright against background.
Decrease the exposure level to allow less light through the lens.
4 Select T, then press SET. Select
“EXPOSURE” (1), then press SET (2).
MANU AL SE T
M
AN. FO CUS
as
1 1 2
SET
SHUT. SP EED EXPOSURE PI C. EF FECT SCENE MENU QK. RETURN DIS RETURN
as
SET
AUTO
M
ANUAL
5 Press a or s to select MANUAL, then
press SET.
The exposure setting screen is displayed.
MANUAL
SRCH
+5
-
0 5
EXPOSURE
+
-
FADE
GAMMA
6 Turn the CONTROL dial up or down to
select the desired exposure level.
The number shown is the selected exposure level. The adjustment range is from -5 (least light) to +5 (most light).
1 Set the camcorder to TAPE-CAMERA,
DUAL-CAMERA or CARD-CAMERA mode.
Features
Advanced
2 Set the EASY/
MANUAL/AUTO Selection switch to MANUAL.
3 Press the MENU/DISPLAY button until
the menu screen appears.
61
7 Press the CONTROL dial to set expo-
sure level.
The selected exposure level is displayed on the menu screen.
MANU AL SE T
M
AN. FO CUS SHUT. SP EED
EXPOSURE
PI C. EF FECT SCENE MENU QK. RETURN DIS RETURN
as
SET
+
3
8 Press the MENU/DISPLAY button to
turn off the menu screen.
T o cancel Manual Exposure mode
After performing step 4 above, select AUTO”, then press SET.
Notes:
Manual Exposure mode will be canceled if a scene setting is selected thereafter.
Setting the Camcorder to Full Auto Mode
Available modes: TAPE-CAMERA, DUAL-
CAMERA, CARD-CAMERA
To easily record good-quality images, perform camera shooting in Full Auto mode. If AUTO is not displayed on the screen, the camcorder is in Manual mode. Perform the procedure below to cancel all the manual settings and set the camcorder to Full Auto mode.
EASY/MANUAL/AUTO Selection switch
Set the EASY/MANUAL/AUTO Selection switch to AUTO.
All the manual settings selected on the MANUAL screen are cancelled.
•“AUTO is displayed.
AUTO
Advanced
Features
Full Auto mode indicator
62
Advanced Features
OFF
AUTO
TELE
AUD I O MODE W
IND
ZOOM MI C
AUD I O SE T
D I A LOG REC RETURN
SET
as
Camera Recording
Using the Zoom Microphone
Available modes: TAPE-CAMERA, DUAL-
CAMERA
With the supplied zoom microphone, you can record audio according to the magnification of the zoom lens to produce the optimum sound. You can also set the zoom microphone to record only sounds at a distance.
Mounting the Zoom Microphone
1 Hold the zoom microphone as shown in
the figure, and mount it to the accessory shoe by sliding it in the direction of the arrow until it locks into place.
Accessory shoe
2 Turn the screw in the direction of the
arrow to secure the zoom microphone.
Screw
Selecting Zoom Microphone Mode
Zoom Microphone mode options
AUTO: The camcorder automatically selects
the optimum sound according to the magnifi­cation of the zoom lens. When the zoom lens is at a wide-angle setting, the built-in microphone is used to record sounds. As the zoom magnification increases, the sounds from the zoom microphone and built-in microphone are mixed according to the zoom setting.
TELE: The zoom microphone is fixed to record
sounds at a distance. (The built-in micro­phone is turned off.)
OFF: The zoom microphone is turned off and
the built-in microphone is turned on. This allows you to record a wider range of sound than with the zoom microphone.
1 Mount the zoom microphone to the
camcorder.
2 In T APE-CAMERA or DUAL-CAMERA
mode, display the menu screen (see page 29).
3 Select U, then press SET. Select
“ZOOM MIC” (1), then press SET (2).
Features
Advanced
Removing the zoom microphone
Turn the screw in the opposite direction than when mounting, and then pull off the zoom microphone.
Cautions:
Use the zoom microphone with the windscreen left on. Taking the windscreen off will significantly increase the volume of wind.
Do not pick up the camcorder by the zoom microphone, as this may cause the camcorder or zoom microphone to break down.
63
as
SET
1 1 2
4 Press f or d to select the desired
zoom microphone mode, then press SET.
The selected zoom microphone mode is displayed on the menu screen.
ZOOM MI C
AUT O
5 Press the MENU/DISPLAY button to
turn off the menu screen.
Notes:
OFF
ON
AUD IO MODE
W
IND
ZOOM M IC
AUD IO SE T
D IALOG REC RETURN
SET
as
• When the camcorder is in EASY mode, the Zoom Microphone mode is fixed to “AUTO” and cannot be selected on the menu screen.
• You can also use headphones while recording. The volume is adjusting with the remote control.
Windbreak
Available modes: TAPE-CAMERA, DUAL-
CAMERA
The windbreak function allows you to reduce annoying noise from strong winds when recording.
1 In TAPE-CAMERA or DUAL-CAMERA
mode, display the menu screen.
2 Select U, then press SET. Select
“WIND” (1), then press SET (2).
AUD IO SE T
AUD IO MODE
as
1 1 2
SET
ZOOM M IC
W
IND
D IALOG REC
RETURN
as
SET
OFF
ON
3 Press f or d to select “ON”, then press
SET.
WIND
ON
4 Press the MENU/DISPLAY button to
turn off the menu screen.
Dialogue Recording
Available modes: TAPE-CAMERA, DUAL-
CAMERA
When you want to record from a distance at a lecture, workshop, or other such occasion, the speaker’s voice may blend in with ambient sounds. You can use the Dialogue Recording function to pick up the speaker’s voice more distinctly.
1 In TAPE-CAMERA or DUAL-CAMERA
mode, display the menu screen.
2 Select E, then press SET. Select
“DIALOG REC”, and then press SET.
3 Press a or s to select “ON”, then press
SET.
DIALOG REC
ON
4 Press the MENU/DISPLAY button to
turn off the menu screen.
To cancel Dialogue Recording
Select “OFF” and then press SET in step 3 above.
Advanced
Features
To cancel Windbreak
Select “OFF” in step 3 above.
Note:
• Keep the windbreak function off during normal recording. If it is left on, the recorded audio may sound somewhat muffled when played back.
64
Advanced Features
Advanced Features
Playback
Playback
Editing
Available mode: TAPE-VCR
Video editing lets you refine your videos by removing unwanted sequences from your tape, or transposing one sequence with another. This camcorder lets you monitor the source programme on the built-in LCD monitor without having to connect it to an external TV or video monitor.
Connect the camcorder to a VCR with the supplied audio/video/S-video cable, as shown.
Recording
CHANNEL
PAUSE /STILL
PLAY
STOP/
POWER
To S-video
input
terminal
Audio/video/S-video cable (supplied)
To AV+S terminal
Notes:
• If your VCR has a 21-pin Euro-SCART connector,
Features
Advanced
use the RCA/21-pin Euro-SCART conversion connector (QSOCZ0033TAZZ).
21-pin Euro-SCART on VCR
0
VIDEO AUDIO
AUDIO
(L/MONO)
(R)
Video
Audio R
Audio L
• If your VCR has an S-video input terminal, you can use the S-video plug of the supplied audio/ video/S-video cable for the video connection on the VCR. (The yellow video plug does not need to be connected to the VCR.)
• If your VCR has only one audio input jack, use the white plug for the audio connection on the VCR.
EJECT
REC
TV/VCRSET UP
Yellow: To video input jack White: To audio input (L) jack Red: To audio input (R) jack
Playback
RCA/21-pin Euro-SCART conversion connector (QSOCZ0033TAZZ)
Cutting Unwanted Sequences
1 Play back the tape to be edited on the
camcorder, and locate the beginning and end of the sequence you wish to cut. Write down the time code readings at the beginning and end of that sequence (see page 50). Then, rewind the tape to before the beginning of the portion that you wish to keep.
2 Load a video cassette into the recording
VCR.
3 Press y to begin playback, and then
press the Record button on the VCR to begin recording.
4 Press the Pause/Still button on the VCR
to pause recording when the source tape reaches the beginning of the sequence to be cut.
5 Press the Pause/Still (or Record) button
on the VCR to resume recording when the source tape reaches the end of the sequence to be cut.
To stop editing
Pressdand press the Stop button on the VCR.
Notes:
• Some of the transitions between edited sequences may be slightly off.
• There may be picture noise during video search or still playback. This does not imply a defect in the camcorder.
• If the date and time and/or the time code are displayed on the camcorder screen, they will be recorded along with the edited sequences. Turn them off if you do not want to record them on the edited sequences (see pages 49 and 50).
• The camcorder cannot be used as the recording source when editing analog signals.
65
Editing with the DV Terminal (IEEE1394)
Available mode: TAPE-VCR
Cutting Unwanted Sequences
Perform Cutting Unwanted Sequences on page 65, using the video equipment as the recording source.
This camcorder enables you to perform digital video editing. Connect the camcorder to video equipment with a DV terminal using the supplied DV cable. The DV cable is able to transfer all dubbing signals including video and audio.
Recording
Video equipment
with DV terminal
(e.g. DV camcorder)
To DV terminal
DV cable (supplied)
To DV terminal
Playback
Note:
Make sure that the video equipment to which you are recording can input dubbing signals via the DV terminal.
Advanced
Features
66
Advanced Features Playback
Audio Dubbing Feature
Available mode: TAPE-VCR
You can add narration to a tape recorded with this camcorder by using the built-in stereo microphone, while preserving the original audio and video recording.
Built-in stereo microphone
Audio Recording
In normal recording mode
12-bit audio recording
The audio is recorded in stereo on Audio 1.
Audio 1: Stereo (left and right) sound Audio 2: No audio
16-bit audio recording
The audio is recorded in stereo with the left and right sound on two separate channels.
Audio 1: Left sound Audio 2: Right sound
In Audio Dubbing mode
12-bit audio recording
The dubbed audio is recorded on Audio 2.
Audio 1: Original stereo (left and right) sound Audio 2: Dubbed stereo (left and right) sound
16-bit audio recording
The dubbed audio is recorded on Audio 2 over the original right sound. Both the dubbed and original sounds are in mono.
Audio 1: Original left sound Audio 2: Dubbed sound
Note:
You can select the 12-bit or 16-bit audio record­ing mode by performing the procedure on page 34.
Features
Advanced
67
Audio Dubbing
DIO
DIO
Note:
Use a Mini DV cassette recorded in SP mode. Audio Dubbing is not possible with LP mode recordings.
1 Play back the recorded Mini DV cassette
and locate the tape position where you wish to start audio dubbing.
2 Press y to pause playback. 3 Press the MENU/DISPLA Y button until
the menu screen appears.
4 Select V, then press SET. Select
“AUDIO DUB” (1), then press SET (2).
The audio dubbing screen appears.
PLAYBACK SE T
as
1 1 2
SET
AUDI O DUB
AUDI O PIC. PB EFFECT M
ULTI FRAME
RETURN
as
AUDIO DUB
EFFECT
SET
EXECUTE
AUDIO
AUDIO
+
+
1 2
12
To pause audio dubbing
Press STOP.
To quit audio dubbing
Press CANCEL. The audio dubbing screen disappears.
If you wish to change the dubbed audio or dub additional scenes
1 Press CANCEL to turn off the audio
dubbing screen.
2 Repeat steps 1 to 5 above.
Notes:
It is recommended that you use Audio Dubbing only with recordings made with this camcorder. Use of recordings made with other digital video equipment may result in poor audio quality.
Audio dubbing will automatically stop if the original audio changes from 12-bit mode to 16­bit mode or vice versa. Press START to resume operation.
Audio dubbing will automatically stop if a portion recorded in LP mode or an unrecorded portion of the tape is encountered.
You can play back the dubbed audio and the original audio together or separately (see Selecting the Audio Playback Mode on next page).
Advanced
Features
START
STOP
CANCEL
5 Press ST ART to begin audio dubbing.
Record your narration.
+
+
AUDIO
1 2
AUDIO
START
STOP
AUDIO DUB
START
STOP
12
CANCEL
68
Advanced Features
TO
Playback
Selecting the Audio Playback Mode
Available mode: TAPE-VCR
You can select any of the following audio playback modes to listen to the dubbed audio.
Audio 1+2
12-bit audio recording in stereo (Audio 1 and Audio 2 channels)
16-bit audio recording in stereo (left and right channels)
Audio 1
12-bit audio recording in stereo (Audio 1 channel only)
16-bit audio recording in mono (left channel only)
Audio 2
12-bit audio recording in stereo (Audio 2 channel only)
16-bit audio recording in mono (right channel only)
1 Play back a Mini DV cassette with
dubbed audio.
2 Press the MENU/DISPLAY button until
the menu screen appears.
3 Select V, then press SET. Select
“AUDIO” (1), then press SET (2).
5 Press the MENU/DISPLA Y button to
turn off the menu screen.
The selected audio playback mode indicator is displayed.
+
+
AUDIO
1 2
AUDIO
AUTO
Audio playback mode indicator
Note:
The audio playback mode indicator, “AUDIO, is displayed in different colours depending on the recording mode (12- or 16-bit) used for the recording being played back. A white display indicates 12-bit recording mode, and a green display, 16-bit recording mode.
12
Features
Advanced
as
1 1 2
SET
PLAYBACK SE T
AUDI O DUB AUDI O
EFFECT
PIC. PB EFFECT M
ULTI FRAME
RETURN
as
4 Press f or d to select the desired
audio playback mode, then press SET.
AUD I O
69
12
+
1
2
1 2
SET
+
Using the Camcorder with Your Computer
It is possible to transfer still images or still playback images from the camcorder to a computer by using the supplied Video Capture Software and PC connecting cable.
Connecting the Camcorder to a Computer
1 Turn off the camcorder and computer. 2 Connect the camcorder to the computer
as shown below.
System Requirements
• IBM PC/AT or compatible with Intel® Pentium 133 MHz or faster processor
• Microsoft Windows 95B, Windows 95C, Windows 98, Windows 98 Second Edition, Windows 2000 Professional*, or Windows Me operating system
• 32 MB or more of RAM
• 9 MB minimum of available hard-disk space
• SVGA (800 × 600 pixels) colour display monitor with 16-bit colour or higher
• CD-ROM drive (for installation)
• RS-232C serial port
• Mouse or other pointing device
*To install the software in Windows 2000 Professional,
you must log in as Administrator.
Installing the Software
1 Turn on the computer and start up
Windows.
2 Insert the CD-ROM of the Video Capture
Software into the CD-ROM drive.
3 Double click on the “My Computer” icon. 4 Double click on the CD-ROM drive icon. 5 Double click on the “Setup.exe” file. 6 Follow the on-screen instructions to
install the software.
7 Restart the computer.
To RS-232C port
®
(D-sub 9-pin port)
PC connecting cable (supplied)
PC COMMUNI­CATION jack
3 Turn on the computer. 4 Turn on the camcorder in the desired
camcorder mode.
Notes:
• It is recommended to use the AC adapter/battery charger as a power source for extended periods of use.
• Images with the following functions cannot be transferred to a computer. —TAPE-VCR/CARD-VCR mode: Playback Zoom,
Picture Effect Playback
—TAPE-CAMERA/DUAL-CAMERA/CARD-
CAMERA mode: digital zoom, digital picture effects, Scene Menu
• Using a commercially available dedicated PC card adapter for each card type, it is possible to transfer still images directly from an SD Memory Card or a MultiMediaCard to a computer (see page 84).
• To edit still images transferred with the Video Capture Software, use commercially available image editing software.
Advanced
Features
70
Advanced Features Playback
Using the PDF Software Manual
The PDF manual for the Video Capture Software is included in the supplied CD-ROM. Refer to the PDF manual for detailed informa­tion on the use of the Video Capture Software.
Note:
For the latest product information concerning the Video Capture Software, be sure to read the Readme text file located in the Readme folder on the supplied CD-ROM. Select the Readme text file in the language you prefer. The letters between “Readme” and “.txt” define the language; for example, “en” in Readmeen.txt stands for English, etc.
Installing Adobe Acrobat Reader
Adobe Acrobat Reader 4.0 or later is required for viewing the PDF manual for the Video Capture Software. If the Adobe Acrobat Reader is not installed on your computer, perform the steps below to install one.
1 Insert the CD-ROM of the Video Capture
Software into the CD-ROM drive.
2 Double click on the My Computer icon. 3 Double click on the CD-ROM drive icon. 4 Double click on the Acroread folder. 5 Double click on the desired language
version.
Features
Advanced
Language File name
Chinese, Simplified ar40chs.exe Chinese, Traditional ar405cht.exe Dutch ar405dut.exe English ar405eng.exe French ar405fre.exe German ar405deu.exe Italian ar405ita.exe Korean ar405kor.exe Portugese ar405por.exe Spanish, Castilian ar405esl.exe Swedish ar405swe.exe
6 Follow the on-screen instructions to
install the software.
7 Restart the computer.
Opening the PDF manual
1 Insert the CD-ROM of the Video Capture
Software into the CD-ROM drive.
2 Double click on the My Computer icon. 3 Double click on the CD-ROM drive icon. 4 Double click on the Manual folder. 5 Double click on the PDF file of the
desired language version.
Adobe Acrobat Reader launches and the selected PDF manual opens.
Note:
If the PDF file does not open, Adobe Acrobat Reader may not be properly installed. Refer to the steps of Installing Adobe Acrobat Reader to check the installation procedure.
Printing the PDF manual
Print out the PDF manual so that you can consult it whenever necessary.
1 Open the PDF manual. 2 Select Print in the File menu.
Note: The menu expressions such as Print
and File may vary according to the language version of Adobe Acrobat Reader installed on the computer.
3 Select your print settings, and then click
OK”.
71
GAMMA
Digital Still Camera Features
AUTO
CARD
8911
NORMAL
GAMMAGAMMAGAMMA
Camera Recording
Card Recording
Available mode: CARD-CAMERA
It is possible to take a still picture in the same way as you do with a standard camera and record that image on the card.
Media Selection switch
Power Zoom buttons
STILL button
POWER switch
1 Insert a card in the camcorder (see
page 15).
2 Remove the lens cap. Pull out the
viewfinder completely or open the LCD monitor.
3 Set the Media Selection
switch to CARD.
4 Hold down the Lock button and set the
POWER switch to CAMERA.
• The camcorder turns on in CARD­CAMERA mode, and the picture from the lens is displayed on the screen.
Number of shots taken
AUTO
NORMAL
5 Press the Power Zoom buttons to frame
the subject as you desire.
Note: In CARD-CAMERA mode, the zoom will give magnification of 1–10×.
6 Press the STILL button to record a still
image of the subject.
• The O indicator flashes red while data is being recorded on the card, and returns to white when recording is completed.
Notes:
• In CARD-CAMERA mode, the angle of field is slightly wider than in TAPE-CAMERA or DUAL­CAMERA mode.
• Recording under insufficient lighting may result in blurred images. It is recommended that you use a tripod to record insufficiently illuminated subjects.
• Recording under the light of a fluorescent, mercury, or sodium lamp may cause flickering in the image and, depending on the timing of the shot, may result in changes to colour hue in the image.
• It is also possible to record still images on a card by pressing the CARD REC button on the infrared remote control.
Caution:
• Do not turn the power off or remove the card
CARD
while the O indicator is flashing in step 6,
9001
because this may delete or damage images on the card.
Digital Still Camera
Features
Lock button
GAMMA
GAMMA
Number of shots remaining
72
Digital Still Camera Features Camera Recording
Selecting the Picture Quality
The picture quality of still images recorded on a card and the number of recordable images depend on picture quality setting. Select the appropriate setting to match the purpose of recording.
Approximate number of recordable images (with the supplied 8 MB MultiMediaCard)
Image size
640 480
NORMAL
Picture quality
Note:
The number of recordable images differs depending on picture quality setting being used and the images being shot.
ECONOMY
FINE
Selecting the Picture Quality
Available modes: CARD-CAMERA, DUAL-
CAMERA
The camcorder compresses each image with the picture quality setting to save memory on a card.
Picture quality options
NORMAL: Records images with standard
picture quality.
ECONOMY: Allows you to take more shots than
in NORMAL mode but with a lower quality.
FINE: Records images with higher quality than
Features
in NORMAL mode but with a lower number of recordable images.
Digital Still Camera
100
180
60
1 In CARD-CAMERA or DUAL-CAMERA
mode, press the MENU/DISPLAY button until the menu screen appears.
2 Select Y, then press SET. Select “REC
MODE (1), then press SET (2).
CARD
as
1 1 2
SET
CAME RA SET
REC MODE SNAP E F F. DGTL Z OOM GUIDE
FRM
FLASH
RETURN
as
SET
NORMAL
ECONOMY FINE
3 Press f or d to select the desired
setting, then press SET.
RE C MOD E
ECONOMY
4 Press the MENU/DISPLA Y button to
turn off the menu screen.
The selected resolution setting indicator is displayed.
AUTO
Resolution setting indicator
Note:
The resolution setting indicator is also displayed in CARD-VCR mode. The resolution setting indicator displayed during playback is based on the amount of data for that recorded image. Since the amount of data differs depending on factors such as image detail, sometimes the resolution setting indicator displayed during playback may not match the resolution setting used during recording.
CARD
COENOMY
70101
73
Recording with the Guide
AUTO
CARD
9001
N0RMAL
GAMMA
Frame
Available mode: CARD-CAMERA
When your subject is a person, displaying guide frames on the screen will give you a gauge for deciding on the size of the subject’s image.
Guide frame options
CLOSE-UP: This will display a guide frame for
recording a person’s face in close-up.
PORTRAIT: This will display a guide frame for
recording an upper-body view of a person.
FULL-BODY: This will display a guide frame for
recording a full-body view of a person.
1 In CARD-CAMERA mode, display the
menu screen.
2 Select W, then press SET. Press a or
s to select GUIDE FRM, then press
SET.
4 Press the MENU/DISPLAY button to
turn off the menu screen.
The selected guide frame is displayed.
To turn off the guide frame
Select OFF and then press SET in step 3 above.
CAME RA SET
REC MODE
as
1 1 2
SET
SNAP E F F. DGTL ZOOM GUIDE
FLASH
RETURN
as
3 Press a or s to select CLOSE-UP”,
PORTRAIT or FULL-BODY, then
press SET.
GUIDE FRM
FULL–BODY
FRM
SET
OFF
CLOSE–UP PORTRA I T
FULL–BODY
CARD
Digital Still Camera
Features
74
Digital Still Camera Features Camera Recording
Recording with the Self-timer
Available mode: CARD-CAMERA
The self-timer function allows you to record images after a time-lag of 10 seconds. This is convenient when you want to record an image of you and your friends together.
1 In CARD-CAMERA mode, press the
MENU/DISPLAY button until the menu screen appears.
MANU AL SE T
M
AN. FO CUS SHUT. SP EED EXPOSURE
PI C. EFFECT SCENE
MENU SEL F T IMER DIS RETURN
as
SET
CARD
2 Select T, then press SET. Select “SELF
TIMER (1), then press SET (2).
CARD
as
1 1 2
SET
MANU AL SE T
M
AN. FO CUS SHUT. SP EED EXPOSURE
PI C. EFFECT SCENE
MENU
SEL F T IMER
DIS RETURN
as
EXECUTE
SET
3 Frame the subject, and then press the
STILL button to set the timer.
The self-timer operating indicator flashes while the timer counts down.
The shutter will be automatically released 10 seconds after, and a still image of the subject is recorded.
Self-timer operating indicator
AUTO
GAMMA CANCEL
Notes:
When recording with the self-timer, stabilize the camcorder in the horizontal plane by attaching it to a tripod, etc.
To pause the selftimer, press the STILL button again in step 3.
To cancel the self-timer, press CANCEL in step
3.
Self-timer mode will be cancelled after recording one image. Repeat steps 1 to 3 to record another image with the self-timer.
Caution:
Do not turn the power off or remove the card once the self-timer operating indicator begins flashing.
CARD
NORMAL
9001
Features
Digital Still Camera
75
AUTO
GAMMA CANCEL
CARD
NORMAL
9001
Using the Flash Light
REC MODE
AUTO
ON
CAME RA SET
FLASH
GUIDE RETURN
FRM
DGTL ZOOM
SNAP E F F.
CARD
SET
as
(Optional Accessory)
Available mode: CARD-CAMERA
Using the flash function of the optional IR & Flash Light VR-3VIF enables you to record good-quality still images even in dark locations.
Mounting the IR & Flash Light
1 Hold the IR & Flash Light as shown in
the figure, and mount it to the accessory shoe by sliding it in the direction of the arrow until it locks into place.
Accessory shoe
2 Turn the screw in the direction of the
arrow to secure the IR & Flash Light.
Screw
Selecting Flash Mode
Flash mode options
AUTO: Flash automatically fires when in a dark
location (“LIGHT” is displayed on the screen) each time you press the STILL button.
ON: Flash fires every time you press the STILL
button.
1 Mount the IR & Flash Light to the
camcorder and then set the Power switch on the IR & Flash Light to FLASH.
2 In CARD-CAMERA mode, display the
menu screen.
3 Select W, then press SET. Press a or
s to select FLASH, then press SET.
as
SET
4 Press a or s to select AUTO or ON,
then press SET.
FLASH
AUTO
Removing the IR & Flash Light
Turn the screw in the opposite direction than when mounting, and then pull off the IR & Flash Light.
Caution:
Do not pick up the camcorder by the IR & Flash Light, as this may cause the camcorder or IR & Flash Light to break down.
Notes:
Using the optional IR & Flash Light will shorten the continuous camera recording time with the battery pack.
For details, see the operation manual of the optional IR & Flash Light.
The IR light cannot be used, even if the VR-3VIF is mounted on the camcorder.
5 Press the MENU/DISPLA Y button until
the menu screen turns off.
The indicator is displayed.
AUTO
NORMAL
Flash indicator
Caution:
• You should never use the flash with the camcorder close to another person.
Notes:
The indicator flashes while the flash is being charged.
If you press the STILL button while the indicator is flashing, flash does not fire but a still image of the subject is recorded.
CARD
9001
Digital Still Camera
Features
76
Digital Still Camera Features Camera Recording
Formatting a Card
Available mode: CARD-CAMERA
In order to use a commercially available card with this camcorder, formatting is necessary before its first use. You also need to format a card when one of the following warning indicators appears, in order to use the card with the camcorder.
•“FORMAT MEMORY CARD”
•“MEMORY CARD ERROR”
•“MEMORY CARD READ ERROR”
•“CANNOT STORE DATA”
Cautions:
Formatting a card deletes all images on the card including the delete-protected images.
Be sure to copy important data on your computer or other media before formatting the card. (See pages 70, 71 and 84 to transfer data on a card to a computer.)
Do not remove the power source during formatting, as this may cause damage to the camcorder or card. It is recommended that you use the AC outlet for the power supply.
1 Insert a card to be formatted in the
camcorder.
2 Set the camcorder to CARD-CAMERA
mode.
4 Select I, then press SET. Select
FORMAT (1), then press SET (2) to display the format screen.
as
1 1 2
SET
OTHERS
FORMAT
SOUND DEMO MODE LANGUAGE RETURN
as
ALL BE ERASED.
YES NO
EXECUTE
SET
FORMAT
DATA WI LL
To cancel formatting, press NO.
5 Press YES to begin formatting.
YES
ALL
DATA WI LL
BE ERASED.
CARD
3 Press the MENU/DISPLAY button until
the menu screen appears.
MANU AL SE T
M
AN. FO CUS SHUT. SP EED EXPOSURE
PI C. EFFECT SCENE
MENU SEL F T IMER DIS
RETURN
Features
Digital Still Camera
77
as
SET
YES NO
CARD
The menu screen is displayed when formatting ends.
6 Press the MENU/DISPLAY button to
turn off the menu screen.
Note:
Use this camcorder to format a card. The
camcorder may not recognize the images on a card formatted by a computer or other equipment.
Digital Still Camera Features
NORMAL
PL AYBACKPLAYBACK
10 0 0006100 0006-
­21
PAGE
54
1
2
3
6
PB
qw
NORMAL
PL AYBACKPLAYBACK
10 0 0009-100 0009-
22
PAGE
1211
10
9
8
7
PB
qw
12912
9
NORMALNORMAL
100 0009-
CARDCARD
MULTIMULTI
q w
MULTI
qw
Playback
Card Playback
Available mode: CARD-VCR
It is possible to play back and view still images recorded on a card on the LCD monitor.
Media Selection switch
POWER switch
1 Open the LCD monitor and adjust the
angle.
2 Set the Media Selection
switch to CARD.
3 Hold down the Lock button and set the
POWER switch to VCR.
• The camcorder turns on in CARD-VCR mode, and the images recorded on the card are displayed in a thumbnail format.
Image number
Lock button
7
8
9
• If the image you want to play back does not appear, press q or w to scroll through the thumbnail images.
qw
4 Press q or w to move the selection
frame to the desired image.
• Each time you press q or w, the selection frame moves backward or forward.
Selection frame
qw
5 Press PB.
• The selected image is displayed in full­screen.
PB
Digital Still Camera
10
PL AYBACK
PLAYBACK
NORMAL
PB
qw
Picture quality indicator
Note: Depending on the amount of data for the recorded image, the picture quality indicator displayed during playback may not match the quality setting used during recording.
1211
100 0012-
10 0 0012-
PAGE
Page display
Features
22
78
Digital Still Camera Features
PROTE CT
PROT E CT
10 0 001 0-100 0010-
22
PAGE
NORMAL
1211
10
9
8
7
SET
qw
RETURN
Playback
Available Operations during Full­screen Display
You can display the full-screen picture of the previous or next image by pressing q or w.
To return to a thumbnail of the images,
press MULTI.
Caution:
In cases where image data created on a computer or recorded on a different camcorder is played back on that equipment and the data may be corrupted (the image may have video noise or be erratic), do not play back that image data on this camcorder. Doing so can sometimes cause abnormal screen display (vertical lines and so on). If this happens, turn off the camcorder power and remove the card.
Delete-protection
Available mode: CARD-VCR
It is possible to prevent your important images recorded on the card from being accidentally erased by using the delete-protection function.
1 In CARD-VCR mode, press the MENU/
DISPLAY button until the menu screen appears.
2 Select O, then press SET. Select
“PROTECT” (1), then press SET (2).
10 0 0012-100 0012-
PAGE
CARD
98
1211
RETURN
as
1 1 2
SET
PLAYBACK SE T
SL I DE SHO
EFFECTPIC.
PROTE C T EXECUTE
DELETE DELETE ALL PR I . ORDER RETURN
as
PROTE CTPROTECT
NORMAL
SET
SET
7
10
W
qw
22
Features
Digital Still Camera
79
3 Press q or w to select the image to be
protected.
qw
4 Press SET to set the protection.
NORMAL
10 0 0009-100 0009-
DE LET EDELET E
22
PAGE
1211
10
98
7
SET
RETURN
qw
SL I DE SHO
W
EFFECTPIC.
DELETE
PROTE C T
PR I . ORDER
DELETE ALL
PLAYBACK SE T
CARD
RETURN
EXECUTE
DE LET EDELET E
NORMAL
10 0 001 2-100 0012-
22
PAGE
1211
10
9
8
7
SET
as
SET
RETURN
qw
The R indicator appears.
Delete-protection indicator
SET
PROTE CTPROTECT
NORMAL
CANCEL
7
10
8
qw
10 0 0010-100 0010-
PAGE
9
1211
RETURN
If you want to protect another image, repeat steps 3 and 4.
5 Press RETURN, then press the MENU/
DISPLAY button to turn off the menu screen.
To cancel the protection setting
1 Select the image for which the protection
setting is to be canceled in step 3 above.
Deleting Stored Images
Available mode: CARD-VCR
You can delete unwanted images to free up memory of a card for new images.
Note:
Deleted images cannot be restored. Check whether or not you want the images before performing the procedure below.
22
Deleting a Particular Image
1 In CARD-VCR mode, press the MENU/
DISPLAY button until the menu screen appears.
2 Select O, then press SET. Select
DELETE (1), then press SET (2).
as
SET
7
qw
10
PROTE CTPROTECT
NORMAL
CANCEL
2 Press CANCEL to cancel the protection.
The R indicator disappears.
7
PROTE CTPROTECT
NORMAL
SET
10
CANCEL
3 Press RETURN, then press the MENU/
DISPLAY button to turn off the menu screen.
Note:
Formatting a card deletes all images on it, including the ones with the delete-protection setting.
8
10 0 0010-100 0010-
PAGE
qw
8
10 0 0010-100 0010-
PAGE
qw
9
1211
22
RETURN
9
1211
22
RETURN
1 1 2
Digital Still Camera
Features
3 Press q or w to select the image to be
deleted.
qw
80
Digital Still Camera Features
SL I DE SHO
W
EFFECTPIC.
DELETE
PROTE C T
PR I . ORDER
DELETE ALL
PLAYBACK SE T
RETURN
CARD
SET
as
Playback
4 Press SET to set the image.
To cancel deletion, press RETURN.
SET
DE LET EDELET E
NORMAL
DEL E T E ?
7
10
YES NO
8
10 0 0009-100 0009-
PAGE
9
1211
5 Press YES to delete the image.
7
YES
10
DE LET EDELET E
SET
8
qw
If you want to delete another image, repeat steps 3 to 5.
10 0 0010-100 0010-
PAGE
9
1211
RETURN
6 Press RETURN, then press the MENU/
DISPLAY button to turn off the menu screen.
Deleting All Stored Images
You can delete all images stored on a card with a press of a button.
Note:
If you want to keep some images on the card, first delete-protect them (see page 79), and then perform the procedure below.
22
1 In CARD-VCR mode, press the MENU/
DISPLAY button until the menu screen appears.
22
2 Select O, then press SET. Select
DELETE ALL (1), then press SET (2).
PLAYBACK SE T
as
1 1 2
SL I DE SHO
SET
PROTE C T DELETE
DELETE ALL
PR I . ORDER RETURN
W
EFFECTPIC.
EXECUTE
CARD
Features
Digital Still Camera
81
as
DE LET E AL LDE L E T E A LL
NORMAL
DEL E T E AL L ?
SET
1 2 3
YES NO
To cancel deletion, press NO.
54
10 0 000 3-100 0003-
PAGE
6
21
3 Press YES to delete all the images.
SL I DE SHO
W
EFFECTPIC.
DELETE
PROTE C T
PR I . ORDER
DELETE ALL
PLAYBACK SE T
RETURN
CARD
SET
as
Slide Show Playback
YES
NORMAL
1 2 3
DEL E T E
ALL
NOW
DEL E T I NG
YES
1 2 3
PL AYBACKPLAYBACK
PB
54
PAGE
NO
54
10 0 0005-100 0005-
PAGE
qw
6
6
Notes:
The protected images cannot be deleted. Cancel the protection setting to delete the image (see page 79).
If a print order is assigned to delete-protected images and you use the Delete All function, the print order will be cancelled (the protection setting will not be cancelled).
It will take some time to complete deleting all the stored images.
Caution:
Do not turn the power off while deleting images.
Available mode: CARD-VCR
It is possible to automatically play back consecutive still images recorded on a card. This is useful when confirming the data recorded on a card.
11
1 Set the camcorder to CARD-VCR mode. 2 Press the MENU/DISPLAY button until
the menu screen appears.
11
3 Select O, then press SET. Select
SLIDE SHOW (1), then press SET (2).
as
1 1 2
PLAYBACK SE T
SL I DE SHO
SET
PROTE C T DELETE DELETE ALL PR I . ORDER RETURN
EXECUTE
W
EFFECTPIC.
CARD
as
SET
Digital Still Camera
Features
82
Digital Still Camera Features
CANCEL
Playback
4 Slide Show Playback begins.
The recorded images will be displayed in full-screen one after another in order of recording.
SL IDE S SHOWSL IDE SHOW
After playing back all the images on the card once, Slide Show Playback automati­cally stops.
CARD
CANCEL
CANCEL
5 Press the MENU/DISPLAY button to
turn off the menu screen.
To stop Slide Show Playback
During slide show playback, press CANCEL, then press the MENU/DISPLAY button to turn off the menu screen.
Notes:
The display interval may vary depending upon the image size.
Slide Show Playback automatically stops if you press the MENU/DISPLAY button.
Slide Show Playback cannot be used with Picture Effect Playback.
Dubbing Images from a Card to a T ape
Available mode: CARD-VCR
Use the procedure below to select still images recorded on a card and dub them to a tape.
1 Insert the recorded card and a Mini DV
cassette in the camcorder.
2 Set the camcorder to TAPE-VCR mode,
then cue to the location on the tape to be dubbed.
3 Set the camcorder to CARD-VCR mode.
987
121110
PL AYBACKPLAYBACK
NORMAL
PB
10 0 0012-100 0012-
PAGE
qw
4 If the image you want to dub does not
appear, press q or w to scroll through the thumbnail images.
5 Press q or w to select the desired
image, then press PB.
The selected image is displayed in full­screen.
22
Features
Digital Still Camera
83
PB
PL AYBACKPLAYBACK
NORMAL
PB
10 0 0009-100 0009-
PAGE
qw
987
121110
22
Loading...