Plasmacluster is a trademark
of SHARP Corporation
SJ-PT596R
REFRIGERATOR - FREEZER
OPERATION MANUAL
CONTENTS
• WARNING .................................................. 2
• CAUTION ................................................... 2
• INSTALLATION........................................... 2
• DESCRIPTION ........................................... 3
• OPERATION............................................... 4
• STORING FOOD........................................ 5
• CARE AND CLEANING.............................. 5
• WHAT TO DO BEFORE CALLING
FOR SERVICE........................................... 6
• SPECIFICATION ........................................ 7
MODEL
SJ-PT555R
SJ-PT596R
Household use only
Free standing type
Thank you for buying this SHARP product. Before using your SHARP refrigerator, please read this operation manual to
ensure that you gain the maximum benefit from it.
WARNING
■ Highly volatile and flammable materials such as ether,
petrol, propane gas, adhesive agents and pure alcohol
etc. are liable to explode. Do not store these materials in
the refrigerator.
■ Dust deposited on the power plug may cause fire. Wipe
it off carefully.
■ Do not attempt to change or modify this refrigerator. This
may result in fire, electric shock or injury.
■ Ensure that the refrigerator presents no danger to
children whilst being stored for disposal. (e.g. remove
the door to prevent child entrapment.)
■ This refrigerator should be disposed of appropriately.
Take the refrigerator to a recycling plant for flammable
insulation blowing gases.
CAUTION
■ Attention about Power supply:
• Do not use an extension cord or adapter plug.
• Make sure that the power cord has not been damaged
during installation or moving. If the power plug or cord
is loose, do not insert the power plug. There is a risk
of electric shock or fire.
• Disconnect from the mains electricity supply by
removing the mains plug from the electricity supply
socket. Do not remove by pulling the mains lead. This
may cause electric shock or fire.
• Should the flexible supply cord be damaged, it must
be replaced by service agent approved by SHARP as
a special cord is required.
■ Do not touch the compressor unit or its peripheral parts,
as they become extremely hot during operation and the
metal edges may cause injury.
■ Do not touch foods or metal containers in the freezer
compartment with your wet hands. This may cause
frostbite.
■ Do not place bottled and canned drinks in the freezer as
they may crack when frozen.
■ The refrigeration system behind and inside the
refrigerator contains refrigerant.
If this system is punctured it could result in serious
damage to your refrigerator, therefore do not allow any
sharp objects to come into contact with the refrigeration
system.
■ In case of gas leak, ventilate the area by opening a
window, etc. Do not touch the refrigerator or the power
outlet.
INSTALLATION
WARNING
■ Do not install the refrigerator in a damp or wet
location as this may cause damage to the
insulation. Condensation may also build on the
outer cabinet and cause rust.
Keep adequate ventilation space around the
1
refrigerator.
The figure shows the minimum required space for
•
installing the refrigerator. The amount of space around
the refrigerator affects the amount of power
consumption.
• Insufficient spacing will decrease cooling efficiency
and increase energy consumption.
This may reduce the life of the unit and void warranty.
Using the two front adjustable feet, ensure that the
2
refrigerator is positioned firmly and level on the floor.
Remove the 2 screws of the cabinet lower part, and
3
use these to fit the foot covers. (supplied inside the
refrigerator compartment)
Connect the power plug to a 230/240 volt. 10 amp.
4
power point.
NOTE
• Position your refrigerator so that the plug is accessible.
• Keep your refrigerator out of direct sunlight.
• Do not place next to a heat generating appliance.
• This refrigerator is designed for indoor use only, do not
place the unit on an unsealed surface.
When transporting
• Using the casters, it is possible to move back and forth.
• Carry the refrigerator by holding the handles located on
the rear and bottom.
60 mm
or more
1500 mm
1400 mm
60 mm
or more
90 mm
or more
Adjustable foot
Foot cover
■ Do not place objects containing liquid or unsteady
objects on top of refrigerator.
■ This refrigerator is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the refrigerator by a person
responsible for their safety. Young children should be
supervised to ensure that they do not play with the
refrigerator.
2
Before using your refrigerator
Clean the inside parts with a cloth soaked in warm water.
If soapy water is used, wipe it off thoroughly with water.
DESCRIPTION
$''4
↢
1
2
3
4
5
6
7
8
9
10
11
12
13
14
SJ-PT596R
15
16
17
18
19
20
21
22
23
17
15
1. Freezer LED light
2. Freezer shelf
3. Movable shelf
4. Ice cube maker
5. Ice cube box
6. Control panel
7. Fresh case & door
8. Refrigerator LED light
9. Refrigerator shelf
10. Hybrid cooling panel (Aluminium panel)
11. Half shelf (1 pair)
12. Fruit and vegetable shelf
13. Fruit and vegetable crisper
14. Adjustable feet & cover
15. Magnetic door seal
16. Flexible pocket
17. Door pocket
18. Refrigerator pocket & cover
19. Utility pocket
20. Egg holder
21. Utility pocket (large)
(Only for SJ-PT596R)
22. Bottle pocket
23. Tube stand
NOTE (Only for SJ-PT596R)
Do not replace the right and left position of the utility
pocket and the utility pocket (large).
SJ-PT555R
19
20
Hints when making ice
Do not over fill the Ice cube trays;
1
otherwise the ice cubes will be joined
together when frozen.
When the ice cubes are made, turn
2
the lever clockwise to empty the ice
into the Ice cube box.
NOTE
To prevent damage to the Ice cube box, do not make ice in
the Ice cube box.
Lever
Ice cube box
Flexible pocket
Tall food items (e.g. pizza box)
can be stored by lifting the partition
from the bottom of the pocket.
Movable shelf
Enables you to store food separately. If used upside down,
you can keep foods neatly within this shelf.
$''4
Hybrid cooling panel (Aluminium panel)
The panel is cooled from the rear, thus indirectly cooling
the refrigerator compartment. In this way, food is
refrigerated gently, without exposing it to cold air flow.
Half shelf
The position of the shelf can be arranged according to the
size of the food items to be stored.
Tube stand
Prevents bottles etc. from falling.
Tube-type food products can also be
stored inside.
Deodorising unit
(In the refrigerator
compartment)
A deodorising catalyst is installed on the routes of cold air.
No operation and cleaning required.
Reversible door
The door can be modified to open from the left with an optional twin kit SJ-L55CRD. For details of the kit and modification
work, please contact a SHARP approved service centre.
CAUTION SHARP recommends that all modification work and a quote are carried out by a competent person.
3
OPERATION
Control panel
1. Display for temperature setting
The preset temperature of compartment selected is
displayed. It is not the actual temperature in the
compartment.
2. Display for compartment selected
3. Select button
The compartment selected can be changed by pressing
the select button.
Press the
select button
Controlling temperature
The refrigerator controls its temperature automatically.
However, if needed, adjust the temperature as follows.
Refrigerator compartment
Adjustable between 0°C and 6°C in steps of 1°C.
Press the select button.
1
lighting
Press the / button and set the temperature.
2
[ : increase, : decrease ]
Press the " " button to finalise the setting.
3
Initial display for
refrigerator compartment
4. / button
Use to select temperature.
5. button
Finalises the temperature setting.
6. Plasmacluster button and display
Press to start / cancel the plasmacluster operation.
NOTE
• The display for temperature setting and selected
compartment will turn off when there is no operation for
1 minute. (When either button is pressed, it lights again.)
• The plasmacluster display stays alight while ever the
operation is selected.
Initial display for
freezer compartment
Plasmacluster
The plasmacluster automatically starts operating when the
refrigerator is powered on.
To cancel operation
Press the " " button (The light turns off).
Freezer compartment
Adjustable between -13°C and -21°C in steps of 1°C.
Press the select button.
1
lighting
Press the / button and set the temperature.
2
[ : increase, : decrease ]
Press the " " button to finalise the setting.
3
To start operation
Press the " " button again.
Notes about PLASMACLUSTER operation
The ioniser inside your refrigerator releases clusters of
ions, which are collective masses of positive and negative
ions, into the freezer and refrigerator compartments.
These ion clusters help to inactivate airborne mold fungus.
• There may be a slight odors in the refrigerator. This is the
smell of ozone generated by the ionizer. The amount of
ozone is minimal, and quickly decomposes in the
refrigerator.
4
mold
fungus
Door Alarm
When the refrigerator or freezer door is left open, the door
alarm will sound.
• The door alarm will sound 1 minute after opening the
door and again after 1 minute (once in each case).
• If the door is left open for approx. 3 minutes, the alarm
will sound continuously.
To cancel alarm signal
Press the select button continuously for 3 seconds or more
while holding down the " " button.
It shows the door alarm stop.
Use the same method to restart the alarm signal function.
STORING FOOD
Refrigeration reduces the rate of food spoilage.
To maximise the shelf life of perishable food products,
ensure that the food is the freshest possible quality. The
following is a general guide to help promote longer food
storage.
Fruit / Vegetables
To minimise moisture loss, fruit and vegetables should be
loosely enclosed in a plastic material (e.g. wrap, bags)
and placed in the fruit and vegetable crisper.
Dairy Products & Eggs
• Most dairy products have a use by date on the outer
packaging which informs the recommended temperature
and shelf life of the product.
• Eggs should be stored in the Egg holder.
CARE AND CLEANING
WARNING
■ Unplug the refrigerator first to prevent electric
shock.
■ Do not splash water directly on the outer cabinet
or the interior. This may lead to rusting and
deterioration of the electrical insulation.
IMPORTANT
To prevent cracking on inside surfaces and plastic
components, follow these tips.
• Wipe any food oils adhered to plastic components.
• Some household chemicals may cause damage, so use
only diluted washing-up liquid (soapy water).
• If undiluted detergent is used or soapy water is not wiped
off thoroughly, cracking of plastic parts can result.
• Wipe any spills from the refrigerator immediately, acid or
alkaline in the food can cause cracking and staining of
plastic parts.
Meats / Fish / Poultry
• Place on a plate or dish and cover with paper or plastic
wrap.
• For larger cuts of meat, fish, or poultry, place to the rear
of the shelves.
• Ensure all cooked food is wrapped securely or placed in
an airtight container.
NOTE
• Evenly place the food on the
shelves to allow the cooling air to
circulate efficiently.
• Hot foods should be cooled before
storing. Storing hot foods
increases the temperature in the
unit and increases the risk of food
spoilage.
• Do not block the outlet and inlet of
the cool air circulating system with
foods or containers; otherwise the
foods will not be evenly cooled
throughout the refrigerator.
• Keep the door securely closed.
Remove the shelves and pockets from the cabinet and
1
door. Wash them in warm soapy dishwashing water;
rinse in clean water and dry.
(Only fruit and vegetable shelf is not removable.)
Clean the inside with a cloth soaked in warm soapy
2
dishwashing water. Then, use cold water to wipe off
soapy water.
Wipe the exterior with a soft cloth each time it is soiled.
3
Clean the Magnetic door seal with a toothbrush and
4
warm soapy dishwashing water.
Wipe the control panel with the dry cloth.
5
NOTE
• Do not use hot water, household cleaning powders, creams
or spray on cleaning products, or any other cleaning
products such as mineral turpentine, methylated spirits,
thinners, petrol etc. These may damage your refrigerator
and may void any warranty.
• If the power supply is disconnected, please wait for at least
5 minutes before re-connecting power.
• The glass shelves weigh approximately 3 kg each. Hold
firmly when removing from the cabinet or carrying.
• Wipe any spills from the control panel immediately, liquid
ingress can damage the electronics.
• Do not drop objects inside the refrigerator or strike the inner
wall. This may cause the inner surface to crack.
For best freezing
• Quality of foods should be fresh.
• Freeze small quantities of food at a time to freeze them
quickly.
• Food should be properly stored or covered and the air
should be removed to seal tightly.
• Evenly place the food in the freezer.
• Label bags or containers to keep an inventory of freezing
food.
Defrosting
Defrosting is fully automatic due to a unique energy saving
system.
If a refrigerator lamp blows
The lamp should only be replaced by a SHARP approved
service centre.
Switching off your refrigerator
If the refrigerator needs to be switched off for an extended
period, the following steps should be taken to reduce the
symptom of mold:
1. Remove all food.
2. Remove the power plug from the power point.
3. Clean and dry the interior thoroughly.
4. Ensure that all the doors are wedged open slightly for
air circulation.
5
WHAT TO DO BEFORE CALLING FOR SERVICE
Before you call for service, check the following points.
Problem Solution
The outside of cabinet is hot when
touched.
When there is refrigerator noise. It is normal for the refrigerator to produce the following sounds.
Frosting or dew generation occurs
inside or outside the refrigerator.
The food in the refrigerator
compartment freeze.
This is normal. The hot pipe is in the cabinet in order to prevent dew
generation.
• Loud noise produced by the compressor when operation starts
--- Sound becomes quieter after a while.
• Loud noise produced once a day by the compressor
--- Operating sound produced immediately after automatic defrost
operation.
• Sound of flowing fluid (gurgling sound, fizzing sound)
--- Sound of refrigerant flowing in pipes (sound may become louder from
time to time).
• Cracking or crunching sound, squeaking sound
--- Sound produced by expansion and contraction of inner walls and internal
parts during cooling.
This may occur in one of the following cases. Use a wet cloth for wiping frost
and a dry cloth for wiping dew.
• When the ambient humidity is high.
• When the door is frequently opened and closed.
• When foods containing plenty of moisture are stored. (Wrapping is required.)
• Is the refrigerator operated for a long time with refrigerator temp. control set
at 0°C?
• Is the refrigerator operated for a long time with freezer temp. control set at
-21°C?
• Low ambient temperature may cause foods to freeze even if refrigerator
temp. control is set to 6°C.
Noticeable odours. • Wrapping is required for foods with strong odours.
• Deodorising unit cannot remove all odours.
If you still require service contact your SHARP approved service centre.
SHARP approved service centre locations can be found in the support area of our website:
Australia : http://www.sharp.net.au
New Zealand : http://www.sharp.net.nz
6
SPECIFICATION
Rated voltage (V~)
Rated frequency (Hz)
Rated current (A)
Rated input of heating systems (W)
Defrosting input (W)
Climate class
Refrigerant
Charge (g)
Insulation blowing gas
Rated storage volume (L)
Rated gross volume (L)
Group (AS / NZS 4474.1)
Net weight (kg)
Outer dimensions
(mm)
Height
Width
Depth
(Including
the handle)
SJ-PT555R SJ-PT596R
230 - 240
50
0.53 - 0.54
160 - 174
160 - 174
T
HFC - 134a
110
Cyclo pentane
514
555
5T
80
1670
800
720
(728) (728)
555
596
82
1770
800
720
• If further depth reduction is required for site access/installation, the doors and control panel can be removed to reduce
the overall depth from 728 mm to 635 mm. Only a SHARP approved service centre can perform removal and
replacement of the doors/control panel. The customer should obtain an estimate from a SHARP approved service centre
prior to purchase.
7
SHARP CORPORATION OF AUSTRALIA PTY.LTD.
A. B. N. 40 003 039 405
1 HUNTINGWOOD DRIVE, HUNTINGWOOD, N.S.W. 2148
P.O.BOX 6827, BLACKTOWN. N.S.W. 2148
SHARP CORPORATION OF NEW ZEALAND LIMITED
59 HUGO JOHNSTON DRIVE PENROSE, AUCKLAND
Printed in Thailand
TINS-A838CBRZ 07LK TH 1
Loading...