Sharp SJ-P43N-SL, SJ-43N-BE, SJ-P47N-SL, SJ-47N-BE Service Manual

1

SJ-P43N/43N
SJ-P47N/47N

SERVICE MANUAL

S6516SE47ATUFT

SHARP CORPORATION

TABLE OF CONTENTS

page

CAUTIONS AND INFORMATIONS ..................................................................................................................2

SPECIFICATIONS ............................................................................................................................................3

DESIGNATION OF VARIOUS PARTS .............................................................................................................5

DIMENSIONS ...................................................................................................................................................6

LIST OF ELECTRICAL PARTS ........................................................................................................................9

WIRING DIAGRAM.........................................................................................................................................10

FUNCTIONS ...................................................................................................................................................14

ASSEMBLING PROCEDURES OF MAIN PARTS AND CAUTIONS .............................................................18

COOLING UNIT ..............................................................................................................................................25

REPLACEMENT PARTS LIST .......................................................................................................................27

Refrigerant; HFC-134a

Refer to "HFC-134a COOLING UNIT" Service Manual for handling this refrigerant.

DESTINATION .........................F

In the interests of user-safety (Required by safety regulations in some
countries) the set should be restored to its original condition and only
parts identical to those specified should be used.

REFRIGERATOR-FREEZER

MODELS

SJ-P43N-SL
SJ-43N-BE
SJ-P47N-SL
SJ-47N-BE

SJ-P43N
SJ-P47N

SJ-43N
SJ-47N

2

SJ-P43N/43N
SJ-P47N/47N

Some household cleaning chemicals may affect the internal
food liner and plastic parts resulting in splitting or cracks
occurring.
When cleaning all plastic parts inside this refrigerator, only
use diluted dishwashing liquid(soapy water). Make sure that
all plastic parts are thoroughly rinsed with water after cleaning.

CAUTIONS AND INFORMATIONS

1. Some foods froze in the refrigerator compartment.

2. Some plastic parts were cracked or split.

Cracking or crunching sound;

Sound produced by expansion and contraction of inner walls and internal parts during cooling.

Squeaking sound;

Sound produced by expansion and contraction of internal parts.

Sound of flowing fluid (gurgling sound, fizzing sound);

Sound of refrigerant flowing in pipes (sound may become louder from time to time).

3. IT IS NORMAL for the refrigerator to produce the following sounds.

Do not place food directly in front of
cold air outlet.
This may lead to the food freezing.

IN
OUT

cold air flow

In case of following troubles, the cause is not related with the failure of refrigerator.
Please mention the correct way to the customer for the use of refrigerator when the repairing.

3

SJ-P43N/43N
SJ-P47N/47N

SPECIFICATIONS

Items SJ-P43N SJ-43N SJ-P47N SJ-47N
Type 2-Door 2-Door
Outer dimensions Height 1700mm(66.9") 1820mm(71.7")
(Including spacer) Width 680mm(26.8") 680mm(26.8")

Depth 660mm(26.0") 660mm(26.0")
Rated storage volume 347 liter (12.3cu.ft) 384 liter (13.6 cu.ft)
(Rated volume) F: 99liter (3.5 cu.ft) F: 99 liter (3.5 cu.ft)

R: 248 liter(8.8 cu.ft) R: 285 liter(10.1 cu.ft)

Gross volume 370 liter (13.1cu.ft) 407 liter (14.4 cu.ft)

F: 107liter (3.8 cu.ft) F: 107 liter (3.8 cu.ft)
R: 263 liter(9.3 cu.ft) R: 300 liter(10.6 cu.ft)

Defrosting System Heater system

Start Automatic

Finish Automatic
Temperature control Automatic (Adjustable)
No-frost freezer Yes
Interior lamp 1
Caster 2
Evaporating pan 1
Refrigerator R glass shelf ass'y 2 - 2 ­Compartment Refrigerator tray(plastic) - 2 - 2

V glass shelf ass'y 1 - 1 -

Vegetable tray(plastic) - 1 - 1

Vegetable case 1

V parting plate 1

R door pocket 1

Egg tray 1

R door pocket S 2

Bottle pocket 1

Bottle stopper 1

Door pocket 1

Fresh case 1
Freezer Freezer tray 1
Compartment Ice cube maker Twin ice cube maker

Ice storage box 1

Door pocket 2
Deodorizing unit 2 ( Honeycomb type)
Plasmacluster Yes No Yes No

RATING

Items SJ-P43N SJ-43N SJ-P47N SJ-47N
Rated voltage (V~) 110
Rated frequency (Hz) 60
Climate class ST
Rated input (W) 129
Rated input of heating elements (W) 128
Refrigerant (Charging quantity) [Non-flammable]

HFC-134a(105g)

Insulation Blowing Gas

[Flammable]

Cyclo pentane (HC)

Net Weight (kg) 70 66 72 68

PLUG TYPE

Plug cord 2 pin
Plug type A-1

Destination mark F

4

SJ-P43N/43N
SJ-P47N/47N

COLOR

Items -BE -SL
Outside color Beige Silver
Inside color White

5

SJ-P43N/43N
SJ-P47N/47N

DESIGNATION OF VARIOUS PAR TS

Upper hinge cover

Hot pipe

Freezer temp. control knob

Hot pipe

Foot cover

Adjustable leg ass’y

Fan motor
Defrost thermostat
Evaporator
Defrost heater

Damper thermostat

Ionizer
(Only for SJ-P43N,SJ-P47N)

Refrigerator temp. control knob
Drain pipe

Vegetable case

Compressor
Starting relay, Overload relay(Protector)

Caster

Freezer
compartment

Refrigerator
compartment

Mark: Cold air flow

Evaporating pan

Defrost timer

Panel P.W.B

(Only for SJ-P43N,SJ-P47N)

Main P.W.B
(Only for SJ-P43N,SJ-P47N)

The names in parenthesis are the denominations
used in the REPLACEMENT PARTS LIST.

1. Freezer temp. control knob

2. Freezer shelf(Freezer tray)

3. Ice cube maker

4. Ice cube box(Ice storage box)

5. Deodorizing unit

6. Fresh case

7. Refrigerator temp. control knob

8. Light(Lamp)

9. Refrigerator shelf

(R grass shelf ass'y / Refrigerator tray)

10. Lever (V-tray control knob)

(Only for SJ-43N,SJ-47N)

11. Shelf

(V grass shelf ass'y / Vegetable tray)

12. Vegetable crisper(Vegetable case)

13. Divider(V parting plate)

14. Evaporating pan

15. Casters

16. Foot cover(Ventilating grille)

17. Adjustable feet(Adjustable leg ass'y)

18. Fan switch

19. Fan & light switch

20. Utility pocket(Door pocket)

21. Magnetic door seal(Door packing)

22. Egg holder(Egg tray)

23. Egg pocket(R door pocket)

24. Small pocket(R door pocket S)

25. Bottle guard(Bottle stopper)

26. Bottle pocket

27. Plasmacluster panel

(Only for SJ-P43N,P47N)

Figure D-1. External Description

1

2
3

4
5

5

7
8

9

11

10

12
13

14
15
17

16

18
19

20

21

23
24

22

25
26

20
21

6

Plasmacluster

27

Figure D-2. Constructions

6

SJ-P43N/43N
SJ-P47N/47N

DIMENSIONS

OUTER DIMENSIONS AND CLEARANCE

Fig. E-1(SJ-P43N,SJ-43N)

Fig. E-2(SJ-P47N,SJ-47N)

680

680

470

660

90

more than

60

more than

60

more than

60

more than

5951022.5

1700

73

16 9.5

1260

1320

1210

(Unit : mm)

1

1: Not include the handle

90

more than

660

60

more than

680

5951142.5

1820

680

470

60

more than

60

more than

73

16

9.5

1260

1320

1210

(Unit : mm)

1

1: Not include the handle

7

SJ-P43N/43N
SJ-P47N/47N

INNER DIMENSIONS

The dimensions between shelves can be changed by setting the shelves on the other rails.

Fig. E-3(SJ-P43N)

Fig. E-4(SJ-43N)

502

502

502

321

531

502

518

242

242

510

526

225

232

89

89

112

99

99

246

307

307

349

188

229

210

118

(172.5)

(133)(172)

226

126

82

539

536

536

508.5

(Unit: mm)

502

502

502

321

531

524

524

502

518

242

242

510

526

225

232

89

89

112

99

99

246

269

269

320

188

229

210

118

(168.5)

(125)

(165)

226

126

82

526

508.5

(Unit: mm)

8

SJ-P43N/43N
SJ-P47N/47N

(Unit: mm)

502

321

502

502

502

518

531

524

524

526

242

242

510

225

232

89

89

112

99

99

246

269

269

320

188

229

210

118

(218.5)

(175)

(185)

226

126

82

526

628.5

(Unit: mm)

307

349

(183)

(192)

307

(222.5)

536

536

539

502

321

502

502

502

518

531

526

242

242

510

225

232

89

89

112

99

99

246

188

229

210

118

226

126

82

628.5

Fig. E-5(SJ-P47N)

Fig. E-6(SJ-47N)

9

SJ-P43N/43N
SJ-P47N/47N

LIST OF ELECTRICAL PARTS

ITEMS TYPE NAME RATING SPECIFICATIONS
Thermostat MM1-8149 125V 6A (At normal notch)

250V 3A ON/OFF : -20 / -25˚C
Defrost thermostat S101 250V 8A Open/Close : 8 / 1˚C
Thermo. fuse SF70E 250V 10A Working temp. : 70˚C
Fan motor 3R00171 110-120V 60Hz Working with ø100 fan
Defrost heater MM1-4266 115V 94.5Ω 140W at 115V
Door switch DSD-5 125V 0.5A 4 terminals push-button type
Damper thermostat MM1-6173 — Open/Close : 5 / 0˚C
Defrost timer TMDFX04FB2 110-127V Integration type

50/60Hz Cycle time : 12h/10h(50/60Hz)

Delay time : 4m48s/4m(50/60Hz)
Lamp socket — 250V 1A E-12(Hard plastic body type)
Lamp — 110V 15W E-12
Compressor FL1568PF 110V/60Hz Cooling capacity : 210W (60Hz)

Main coil : 1.99Ω

Aux. coil : 3.27Ω

(at 75˚C)

Starting relay P5T0SAT — 5.6 Ω
Overload relay(Protector) 3.6C36C1 — Open/ Close : 130/60˚C
Running Capacitor — 250V 14µF—
Ionizer-K

(Plasmacluster unit)

FTRN-A014CBKZ DC12V 3.5kV p-p

(Only for SJ-P43N,P47N)

Common

Main coil

Aux. coil

10

SJ-P43N/43N
SJ-P47N/47N

WIRING DIAGRAM

Be sure to replace the electrical parts with specified ones for maintaining the safety and performance of the set.

Figure W-1. Wiring Diagram (SJ-P43N,P47N)

Figure W-2. Wiring Diagram (SJ-43N,47N)

11

SJ-P43N/43N
SJ-P47N/47N

Figure W-3. Electric Accessories Layout (SJ-P43N,P47N)

Cabinet ass’y

E.V. cover ass’y

Lead EV-cover ass’y

Fan motor

F-thermostat

Def thermo. ass’y

Fuse ass’y

FM

Def. heater ass’y

Door switch

2 (PUSH OPEN)

3 (PUSH CLOSE)

4 (PUSH OPEN)

1 (NEUTRAL)

1

2

1

2

1

2

1

2

1

2

3

4

1

5

2

6

3

7

4

8

1

5

2

6

3

7

4

8

GY-1

OR-1

R-1

BR-1

Y-1

W-1

BL-1

BL-2

BR-2

SB-1

(SB-1)

BK-1

(W-1)

Y-2

(OR-1)

R lamp box ass’y

Lamp 15W

Lamp socket

L

GY

BR

OR

Y

R

P

BL

BK

SB

G-Y

W

: GRAY

: BROWN (live)

: ORANGE

: YELLOW

: RED

: PINK

: BLUE (neutral)

: BLACK

: SKY-BLUE

: GREEN-YELLOW (earth)

: WHITE

1

2

3

4

OR-4

BR-6

BL-3

GY-3

PWB

HARNESS

MAIN

PWB

1

2

3

1

2

1

2

1

2

1

2

1

2

CLUSTER

HARNESS PU

CLUSTER

HARNESS

Plasmacluster unit

(Ionizer-K)

1

2

3

1

2

3

CAB

HARNESS

1

2

3

PANEL

PWB

F-Door

DOOR HARNESS

BL

1

2

3

4

1

2

3

4

Terminal box Terminal box B

TM

Defrost timer

(Y-1)

(Y-2)

(R-1)

(BK-1)

GY-2

Compressor

C

M

A

Starting

relay

Source plug / cord

BROWN

BLUE

GRAY

ORANGE

Terminal block

Overload relay

(Protector)

1

Running capacitor

12

SJ-P43N/43N
SJ-P47N/47N

Figure W-4. Electric Accessories Layout (SJ-43N,47N)

Cabinet ass’y

E.V. cover ass’y

Lead EV-cover ass’y

Fan motor

F-thermostat

Def thermo. ass’y

Fuse ass’y

FM

Def. heater ass’y

Door switch

2 (PUSH OPEN)

3 (PUSH CLOSE)

4 (PUSH OPEN)

1 (NEUTRAL)

1

2

1

2

1

2

1

2

1

2

3

4

1

5

2

6

3

7

4

8

1

5

2

6

3

7

4

8

GY-1

OR-1

R-1

BR-1

Y-1

W-1

BL-1

BL-2

BR-2

SB-1

(SB-1)

BK-1

(W-1)

Y-2

(OR-1)

R lamp box ass’y

Lamp 15W

Lamp socket

L

GY

BR

OR

Y

R

P

BL

BK

SB

G-Y

W

: GRAY

: BROWN (live)

: ORANGE

: YELLOW

: RED

: PINK

: BLUE (neutral)

: BLACK

: SKY-BLUE

: GREEN-YELLOW (earth)

: WHITE

BL

1

2

3

4

1

2

3

4

Terminal box

TM

Defrost timer

(Y-1)

(Y-2)

(R-1)

(BK-1)

GY-2

Compressor

C

M

A

Starting

relay

Source plug / cord

BROWN

BLUE

GRAY

Terminal block

Overload relay

(Protector)

1

Running capacitor

13

SJ-P43N/43N
SJ-P47N/47N

Figure W-5. Circuit Diagram (Only for SJ-P43N,P47N)

1

2

3

4

5

6

7

8

9

10

11

12

13

1. Resistance which is not specified : 5% 1/8W

2. Rated voltage of

thecondenser

which is not specified : 25V

[ NOTE ]

5

3

7

1

1

1

3

2

2

1

3

2

CN1

CN3

CN2

CN4

SW

2A

2A

F-FM

PC

(PANEL PWB)

(MAIN PWB)

(A/D)

D5

D4

R1 R2 R3

R5

2.2K

R21

(1/2W)

680

C7

0.1

R4

10K

R7

1K

R12

2.2K

R10

2.2K

R8

10K

4.7K R20

1M R6

RS1

RS2

RS3

R18

10K

R14

1K

R16

10K

R17

(1/2W)

1.8

R11

1K

R9

1K

R13

4.7K

R15

4.7K

PC1

PC123

CF1 CST4.00MGW

TMP47C241N

INPUT VOLTAGE

D6

D3

VRS1

C13

0.1

C15

100

10V

C10

1

50V

C9

0.1

VRS2

Q7

KRA101M

Q5

KRA101M

Q4

KRC101M

Q3

KTA1046

Q6

KRA101M

Q1

KRA101M

Q2

KRC101M

C2

2200

35V

R19

OPEN

C16

0.1

C18

0.1

C19

1000

25V

C8

0.1

C6

0.1

C4

0.1

C20

100

10V

C17

100

10V

12V

12V

12V

5V

G

IIOO

G

HS

IC2IC1

IC4

7812 7805

C3

0.1

50V

TRNS IN4005E

PST993E

IC3

D1

IN4007E

D2

ISS270A

D7

ISS270A

ZD1

LED1

C1

0.1

C11

0.1

C12

0.1

C5

1

50V

13

2

VAREF

R40(AINO)

R41(AIN1)

R42(AIN2)

R43(AIN3)

R71(WT0)

R80(INT2)

R81(T2)

R82(INT1)

P10

P11

P12

P13

VSS

VDD

K03

K02

K01

K00

HOLD

RESET

XOU

XIN

TEST

R92

R91

R90

P20

220 240V

120V

110 120V

RS1,2,3=43K(1/2W), RS3=OPEN, VRS1,2=560V

RS1,2,3=18K(1/2W), RS3=10K(1/8W), VRS1,2=270V

RS1,2,3=18K(1/2W), RS3=SHORT,

VRS1,2=270V

250V

PC

:

PLASMACLUSTER UNIT

(IONIZER-K)

14

SJ-P43N/43N
SJ-P47N/47N

FUNCTIONS

1. ADJUSTABLE TEMPERATURE CONTROL
(1) Temperature control of freezer

Thermostat (senses freezer temperature) operates on ON/OFF switchover to control the compressor and
cool air circulating fan , and allows the freezer temperature to keep at a suitable temperature.
However adjust the freezer temp. control knob as follows depending upon the storing condition of foods.

KNOB
SETTING

MAX

(Coldest)

MIN

PURPOSE

For making ice rapidly or fast freezing.

For storing frozen food for a short period (up to one month).
When frozen food or ice cream is not stored.

For normal freezing.

MED

When restocking with fresh food.

KNOB
SETTING

MED

Coldest

MIN

PURPOSE

For keeping freshness of food longer.

For normal operation.
When the refrigerator provides excessive cooling.

When the refrigerator does not provide sufficient cooling.

The values shown above refer to the measurement carried out center area and 1/3 of overall height from the bottom
at each of the refrigerator and the freezer after machine has been operated at an ambient temperature of 30˚C with no
food stored and the door closed until the temperature is stabilized.
The values vary depending upon frequency of opening and closing the door, ambient temperature, amount of stored
foods and manner of storing foods.

SETTING OF
REFRIGERATOR TEMP.
CONTROL KNOB

Refrigerator
temperature

Fresh case
temperature

Coldest MED MIN

Approx.

0˚c

Approx.

-3˚c

Approx.

3˚c

Approx.

1˚c

Approx.

6˚c

Approx.

4˚c

The values shown above refer to the case where the
freezer temp. control knob is set at "MED".

Figure F-2.

NOTE: The refrigerator temperature is affected also by the freezer temperature. If the freezer temp.

control knob is set at the position "MAX", the temperature tends to be lower than the following
values, and if set at near the position "MIN", temperature tends to be higher.
If the refrigerator is operated for a long time with the freezer temperature control sets the "MAX"
position, foods stored in the refrigerator compartment may also freeze.
When refrigerator temperature control sets to the "Coldest", some foods stored may freeze.
In this case adjust control set back to the "MED" position.
When refrigerator temperature control sets to the "Coldest", some foods stored in Fresh case may
also become frozen.

(3) Reference value of temperature

SETTING OF
FREEZER TEMP.
CONTROL KNOB

Freezer
temperature

MAX

(Coldest)

MED MIN

Approx.

-21˚C

Approx.

-18˚C

Approx.

-15˚C

Figure F-1.

(2) Temperature control of refrigerator

Damper-thermostat senses temperature of the refrigerator and changes the opening angle of the damper
automatically.
However, as the Damper-thermostat has no function to switch on or off the compressor and fan motor, the
freezer temperature control causes temperature in the refrigerator to vary to some extent.
However, adjust the refrigerator temp. control knob as follows depending upon the cooling condition.

15

SJ-P43N/43N
SJ-P47N/47N

(2) Where is melted frost brought

1. Melted frost is brought into the evaporating
pan at the back of the set and is evaporated
here by the heat of compressor.

2. Be sure to use Evaporating pan as inserted
so as to be level with the outer case.

2. DEFROSTING
(1) No defrosting operation is necessary

No defrosting operation is necessary.
As this machine is so designed that a built-in
evaporator cools air and a fan circulates cooled
air, neither the freezer nor the refrigerator is
frosted, though the evaporator is frosted.
The frosted evaporator is defrosted automatically
due to the function of defrosting timer and heater,
requiring no defrosting operation.

(3) The following circuit diagrams in the table show automatic defrosting function of the refrigerator with

timer and defrost thermostat.

Operation Electric diagram Description

1. Cooling
(Normal)

2. Defrosting

(Time 20 to 30 min.)

3. Drain

(Time approx. 5 min.)

4. Restart

(Time approx. 5 min.)

The integration timer integrates running
time of the compressor. When it reaches
cycle time of defrost timer, the timer
contact is changed to start defrosting.

When the defrost thermostat becomes
OFF, the timer motor starts running.
During the operation time (delay time
of defrost time)

defrosted water is

drained outside the refrigerator.

Timer contact is changed to cooling
operation and the compressor starts
running and the timer motor stops.
Defrost thermostat contact becomes ON
when it’s cooled. And the timer motor
starts running. (Figure F-3.)

Figure F-3.

Figure F-4 .

Figure F-5.

Figure F-6.

TM COMP

Defrost thermostat ON Compressor running

Timer motor running

Timer contact

Defrost
thermostat (ON)

Defrost heater

Thermo. fuse

Compressor

Timer motor

SOURCE

TM COMP

Defrost thermostat OFF Compressor running

Timer motor stops

Thermostat Timer contact

Defrost
thermostat (OFF)

Defrost heater

Thermo. fuse

Compressor

Timer motor

SOURCE

TM COMP

Defrost thermostat OFF Compressor stops

Timer motor running

Thermostat Timer contact

Defrost
thermostat (OFF)

Defrost heater

Thermo. fuse

Compressor

Timer motor

SOURCE

TM COMP

Defrost thermostat ON Compressor stops

Timer motor stops

Thermostat Timer contact

Defrost
thermostat (ON)

Defrost heater

Thermo. fuse

Compressor

Timer motor

SOURCE

Thermostat

The timer contact is changed to start
defrosting, the timer motor stops, and
power is supplied to the defrost heater.
It takes about 20 to 30 min. to defrost.
When little frosted, the defrosting takes
little time. When much frosted, the def­rosting takes much time.

16

SJ-P43N/43N
SJ-P47N/47N

(4) As a reference to determine the causes of trouble, malfunction and phenomena are described below.

Refer to the following when repairing.

1. Disconnection of defrost heater

As off-cycle defrosting is performed, the defrosting time is extremely prolonged. Each time defrosting is
started, the freezer temperature rises and a portion of ice and stored foods are melted.

2. Melted thermo. fuse or opened-circuit due to the defect of defrost thermostat.

When the above mentioned trouble occurs in cooling operation, the timer motor does not run, defrosting
will not take place, and consequently freezing is caused. In the above mentioned condition, when the timer
shaft is turned by hand to defrost, the timer motor runs during the operation time. However, the motor stops
from the time when the contact is changed, and freezing causes.

NOTE:

As the thermo. fuse assembly is intended to prevent dangers, do not use it under shorted condition even
for a short period.

3. DEW PREVENTION

The hot pipe, namely D.P.-condenser, is arranged around the flange part of
cabinet and the C-partition plate, preventing dew from being generated on
the cabinet.

NOTE:

D.P.-condenser pipe may be felt hot if touched by hand while the
compressor is in operation.
If you are asked about this, please explain that the hot pipe serve to
prevent the dew generation.

Figure F-7

4. INSPECTION OF INITIAL STARTING
(1) Inspection of cooling unit

1. Set the temperature control knob to "MAX" and check that the compressor starts to operate.

2. Depress the door switch to run the fan and check that cool air is blown out of the cold air outlet of the
freezer and the refrigerator.

3. When the compressor does not work, check that the timer is not set to "defrost" position.

4 It takes about an hour and a half or two hours to put food in the refrigerator after starting operation.

NOTE:

After return the temperature control knob to "MED" position.
When the refrigerator is operated initially after installed, the compressor may vibrate excessively for 1 to 2
min. However, vibration becomes normal if it is continuously operated.

(2) Inspection of defrost device

Operate the refrigerator for 20 to 30 min. and then check the defrost device in the following procedures :
Allow 5 min. to restart the compressor since immediate starting after stopping will cause unsmooth operation.

1. Turn the timer shaft clockwise with a screw driver.
At this time, make certains the timer clinks and the compressor stops.

2. After more than 5 min., turn the shaft further to operate.
Make certain cooling operation is started again.

Hot pipe

17

SJ-P43N/43N
SJ-P47N/47N

5. PLASMACLUSTER (Only for SJ-P43N,P47N)
(1) Plasmacluster is what thing.

The ionizer inside the refrigerator will release cluster ions, which are collective mass of positive and negative
ions, into the the freezer and refrigertor compartments.
The cluster ions inactivate airborne fungus.

(2) Plasmacluster Panel

1.When the refrigerator will be operated, the

Plasmacluster

lamp of the

panel will light up.

2.By pushing the button, the lamp goes out or lights up.

3.Under the lamp is lighting, Plasmacluster operation is controlled as
follows.

(3) Plasmacluster Control.

1.Plasmacluster operation will be performed when the following conditions
gather.

1) Lamp : Under lighting

2) Compressor : Under operation

3) Door : Closed

4) Within

"

The Plasmacluster operation time".

2.If the sum total of Plasmacluster operation time will reach at the set time (

"The Plasmacluster operation Time"

) ,

Plasmacluster operation will stop.

3.

After an operation stop, the

Plasmacluster

will be not operated during the set time ("The Plasmacluster operation

compulsive stop time"

) .

Time chart A

Compressor               

ON

Fan motor   

Door

Plasmacluster  

  t1 t2 t3

Time chart B

Compressor               

Fan motor            

Door

Plasmacluster  

        t1 t2 t3

Plasmacluster

Plasmacluster panel

Lamp

Button

The Plasmacluster operation time = t1 + t2 + t3

18

SJ-P43N/43N
SJ-P47N/47N

ASSEMBLING PROCEDURES OF MAIN PARTS AND CAUTIONS

CAUTION: DISCONNECT THE UNIT FROM THE POWER SUPPLY BEFORE ANY REPAIRING.

1. R-AIR GUIDER ASSEMBLY

Figure A-1

After forming, fix it to the refrigerator.

Less than 160 mm

Damper
thermostat

5

1

mm

8

1

mm

Less than 12 mm

NOTE
Minimum bending radius is R5mm.
There should be no gas leak by reforming of sensor tube.

++

Figure A-2

(1) Forming sensor of Damper thermo.

(2) Setting R air guider S (Only for SJ-43N,47N) and sticking sealers to R air guider.

R air guider

R air guider S

A-sealer ag1A-sealer ag1

Masking tape

A-sealer ag3

A-sealer ag2A-sealer ag2

Dial sealer

R air guider

A-sealer ag1

A-sealer ag1

OVERLAP AREA

OVERLAP 8mm

OVERLAP 15mm

OVERLAP 15mm

DATUM

DATUM

DATUM

(Only for SJ-43N,47N)

Figure A-3

Damper thermo.

A-sealer ag3

A-sealer ag2

Dial sealer

R air guider

R air guider S

Ionizer-K

Plasma holder

Plasma harness

A-sealer ag1

(Only for SJ-P43N,P47N)

(Only for SJ-43N,47N)

19

SJ-P43N/43N
SJ-P47N/47N

(3) Fixing of the Ionizer-K.(Only for SJ-P43N,P47N)

(3)-1 Connect Ionizer-K and connector of the lead wire.
(3)-2 Insert Ionizer-K to Plasma holder.
(3)-3 Insert the (3)-2 assembly to R air guider A.

２Ｐ

２Ｐ

２Ｐ

２Ｐ

Ionizer-K

R air guider A

Plasma harness

Paper tape W30×100mm

Paper tape W30×40mm

Paper tape W30×40mm

Plasma holder

Ionizer-K

Plasma harness

Connector should insert surely.

SEC. A—A

SEC. B—B

A

B

B

A

20

SJ-P43N/43N
SJ-P47N/47N

(2) Fixing of Fan motor and Fan

(2)-1 Stick U-sealer handle to Fan motor holder A.

Figure A-6

2. FAN LOUVER AND E.V COVER ASSEMBLY

Figure A-4

E.v cover sealer C

E.v cover
sealer C

Fuse ass’y

F-thermostat

E.v cover

Defrost thermo.
ass’y

E.v cover
sealer A

E.v cover
sealer G

L-band C

L-band C

Lead EV-cover
ass’y

U-sealer
handle

Fan motor
holder A

Fan clamp

Propeller fan
100

Fan motor holder B

Fan motor

Motor cushion

E.v cover
sealer B

E.v cover sealer D

E.v cover sealer E

E.v cover
AL A

E.v cover
sealer F

Fan motor holder A

U-sealer handle

U-sealer handle

7 2mm

+

+

0 1mm

C

C

SEC. C-C

E.v cover sealer C

E.v cover sealer G

E.v cover sealer A

E.v cover sealer B

E.v cover

[back side]

STICK START

STICK START

STICK START

(1)

(1)

(2)

(3)

(3)

(4)

(4)

(4)

Screw

Fan louver

Screw

Claw

Claw

Claw

Claw

2-1. How to remove the Fan louver

(1) Take out 2 screws.
(2) Insert the screwdriver into the air hole of the Fan

louver.

(3) Press the Fan louver to the left side with the

screwdriver,and pull it toward yourself to take off the
Fan louver.

2-2. E.v cover assembly

Figure A-5

Figure A-7

(1) Sticking of Sealers to E.V cover

21

SJ-P43N/43N
SJ-P47N/47N

(2)-4 Set Fan clamp to Propeller fan 100 and insert

it to the shaft of Fan motor.

(2)-2 Insert the terminals of Lead EV-cover ass'y to

Fan motor.

(2)-3 Fix two Motor cushions to Fan motor, and set it

at Fan motor holder A and B.
Then fix with Tapping screw.

Figure A-8

(3) Setting of Fan motor ass'y , Defrost thermo. ass'y and Fuse ass'y.

Fan motor
holder A

Fan motor
holder B

Motor cushion

Tapping
screw

Fan motor

Lead EV-cover ass’y

RED

BROWN

Fan clamp

Propeller
fan 100

Fan clamp

Slit

Slit of each Fan clamp
and Propeller fan
should not be at same position.

Shaft

4 0.5mm

+

Detail of D

D

Note
Propeller fan should not be
taken out from shaft when
pulled by 3 kgf.

×○

Fan clamp

Propeller fan

Figure A-10

[front side]

more than 3.5mm more than 3.5mm

Lead e.v cover
ass’y

E.v cover sealer C

Take out lead wire
from square hole to
front and fix with
L-band C, then seal
with E.v cover sealer C

Aluminum tape

Aluminum tape

Aluminum tape

Aluminum tape

Tapping screw

Set metal side below

L-band C

L-band C

L-band C

Fuse ass’y

[back side]

Defrost thermo.
ass’y

Tapping screw

E.v cover

F

G

F

H

H

Defrost thermo.
ass’y

CUT

Not come out of claw.

10 5mm

+

SEC. F F

Turn up lead wire

ATTENTION

SEC. H H

Fuse ass’y

E.v cover
sealer E

Detail of G

E.v cover sealer E

[Front side]

E.v cover AL A

E.v cover sealer F

Figure A-9

22

SJ-P43N/43N
SJ-P47N/47N

50mm

8.5mm

21mm

R10mm

R10mm

(5) Setting of F-thermostat

(5)-1 Form capillary tube of F-thermostat.

Note

• Bending radius of
capillary tube should be

from R5mm to R10mm.

Figure A-13

(5)-3 Set to E.V cover.

Stick E.v cover sealer D.

(5)-2 Insert terminal of Lead EV-cover ass'y.

After inserting, fix with vinyl tape.

Figure A-11

1234

5678

F-thermostat 2

F-thermostat 6
(BROWN, inserted)

Fuse 8 (BLACK)

Fuse 8 (WHITE)

Fan motor 1 , 5

(RED, inserted)

Defrost thermo. 3 (PINK)

Defrost thermo. 7 (BLUE)

WIRE COLOR FOR FAN MOTOR

100-110V : WHITE

127V : YELLOW

220-240V : BLUE

Note Pins should be inserted surely,
and check by pulling it.

Figure A-12

Vinyl tape

Figure A-14

Figure A-15

RED

BROWN

(front side)

(back side)

F-thermostat

SEC. B B

B

B

E.v cover sealer D

(4) Inserting of pins

23

SJ-P43N/43N
SJ-P47N/47N

Fig. A-16

(1)-2. As shown in Fig. A-17, pull the upper part of

Evaporator toward you, pull it diagonally so that
the pipe of Evaporator does not contact the convex
part of food liner.

3. DEFROST HEATER

(1) Taking-out Evaporator

(1)-1. Take out E.v cover ass'y (Fig. A-16).

Evaporator

Food liner convex part

Food liner convex part

Evaporator

Pipe

Fig. A-17

(1)-3. As shown in Fig. A-18, bend the removed

Evaporator horizontally so that Defrost heater can
be replaced easily.

NOTE: When pulling Evaporator and bending the

pipes, pay attention so as not to break and
deform the pipes. Still, take care not to hurt
yourself by fin of Evaporator.

Fig. A-18

Evaporator

(2) Replacement of Def. heater ass'y.

(2)-1 Remove the center screw of Drain support al

to take it off from the food liner.

Fig. A-19

(2)-2 Raise the protrusion part of Drain support al.

Then remove Heater cover.

Fig. A-20

(2)-3 Open Def.heater fixed part of Drain support al to

the right and left, then remove Def.heater ass'y.

Screw

Drain support al

Drain support al

Heater cover

Protrusion parts

Protrusion part of Drain support al(2 pcs.)

Heater cover

Def. heater ass’y

Fig. A-21

Fixed parts

Drain support al

Def.heater ass’y

24

SJ-P43N/43N
SJ-P47N/47N

Fig. A-26

(2)-9. Wind up Leading wire sealer as shown in Fig. A-27

Fig. A-25

(2)-8. Set Heater cover on Drain support, and bend top

edge c and d to outside as shown in Fig. A-26.

Fig. A-23

(2)-6. Bend a and b of Drain support al to right angle

(90˚) to set Def. heater ass'y. (Fig. A-24)

Fig. A-22

(2)-5. Wind the Glass cloth tape (3M: No. 27) to lead wire

of Def. heater ass'y. (2 places)

(2)-4. Replace Def. heater ass'y with new one. (2)-7. Stick the longer wire to the Drain support by

aluminum tape (2 pieces), and wind vinyl tape
(2 pieces) to lead wires of Def. heater ass'y by
aluminum tape as shownin Fig. A-25.

Note: Glass cloth tape part shall be both side of Drain

support to protect the lead wire from damaged.

Fig. A-24

Heater cover

Def.heater ass’y

Drain support al

Def. heater ass’y

Glass cloth tape
(W40 x L25)

Glass cloth tape
Wind the Glass cloth tape
more than 2 turns.

360

(40)

(40)50

Lead wire

+

+

5

5

Drain support al

This side is longer wire

This side is shorter wire

Def.heater ass’y

a

b

Glass cloth tape

Glass cloth tape

Glass cloth tape

Glass cloth tape

aluminum tape

(more than 2 turns)

[back side]

[bottom side]

A

A

Sec. AA

(W25 X L40)

Fig. A-27

(2)-10

. Set the assembly above on the food liner by fixing

a screw.

top edge

Drain support al

Heater cover

Heater cover

Def.heater ass’y

Def.heater ass’y

c

d

Sec. BB

B

B

Drain support al

Heater cover

Def.heater ass’y

190 20

+

Leading wire sealer

25

SJ-P43N/43N
SJ-P47N/47N

COOLING UNIT

Figure C-1. Cooling unit

Hot pipe L
(Side condenser)

Hot pipe
(DP-condenser)

Hot pipe R
(Side condenser)

Evaporator

Suction pipe

Compressor

Capillary tube

Dryer

Back condenser

Mark: Refrigerant flow
Mark: Brazing portion

Eva-pan pipe

(3) Installing of Evaporator
(3)-1. Install Evaporator as shown in Fig. A-16 in the

reverse order of Fig. A-17.

(3)-2. Correct the deformed fin.

NOTE

1. When installing Evaporator, take care not to

deform significantly and break the pipes.

2. Take care not to damage the lead wires and hurt

yourself by the fin of Evaporator.

26

SJ-P43N/43N
SJ-P47N/47N

From Suction pipe
to SP connector

From Compressor
to Charge pipe

From Dryer
to Capillary tube

From Discharge p connector
to Eva-pan pipe ass’y

From SP connector
to Compressor

From Compressor
to Discharge p connector

From Eva-pan pipe ass’y
to Back condenser In

From Back condenser out
to Hot pipe

From Hot pipe
to Dryer

Figure C-3. Location

Figure C-2. Location

Compressor

Suction pipe

Charge pipe

Charge pipe

Capillary tube

Dryer

Hot pipe

S.P. connector

Eva-pan pipe

Back condenser

Evaporator

27

SJ-P43N/43N
SJ-P47N/47N

REF. NO. PART NO. DESCRIPTION Q'TY CODE

REPLACEMENT PARTS LIST(SJ-P43N/43N/P47N/47N)

SJ-P43N SJ-43N SJ-P47N SJ-47N

-SL -BE -SL -BE

ELECTRIC PARTS

1- 1 RTHM-A103CBZZ F-themostat 1 1 1 1 AV
1- 2 RSTT-A176CBZZ Starting relay 1 1 1 1 AS
1- 3 QSWTDA025CBE0 Defrost timer 1 1 1 1 AW
1- 4 PDMP-A050CBEZ Damper thermo 1 1 1 1 AW
1- 5 FTHM-A039CBKZ Defrost thermo.ass’y 1 1 1 1 AM
1- 6 RMOTRA071CBZZ Fan motor 1 1 1 1 AY
1- 7 QSOCAA084CBEZ Lamp socket 1 1 1 1 AL
1- 8 RLMP-A028CBEZ Lamp15w 1 1 1 1 AG
1- 9 QACC-A160CBZZ Source cord 1 1 1 1 AP
1- 10 QSW-PA090CBZA Door switch 1 1 1 1 AS
1- 11 RHOG-A165CBZZ Protector 1 1 1 1 AZ
1- 17 FFS-TA061CBKZ Fuse ass’y 1 1 1 1 AM
1- 20 FW-VZA148CBEZ Lead ev-cover ass’y 1 1 1 1 AL
1- 21 FHETBA164CBEZ Def.heater ass’y 1 1 1 1 AX
1- 22 FCNW-A733CBKZ Relay wire ass’y 1 1 1 1 AP
1- 23 QCNW-A671CBE0 Reray wire rc 1 1 1 1 AD
1- 32 RC-EZA197CBZZ Capacitor 1 1 1 1
1- 33 QCNW-A886CBE0 Olr cord 1 1 1 1 AE
1- 34 QCNW-A887CBE0 Earth wire 1 1 1 1 AG
1- 45 FTRN-A014CBKZ Ionaizer-k 1 - 1 - AZ
1- 46 QCNW-B104CBZZ Plasma harness 1 - 1 - AF
1- 50 FPWB-A347CBKZ Main pwb 1 - 1 ­ 1- 55 FPWB-A336CBKZ Panel pwb ass’y 1 - 1 - AT

MECHANICAL PARTS

2- 2 JKNB-A036CBFC F-temp. control knob 1 1 1 1 AC
2- 4 LANG-A059CBPZ Eva holder 47 2 2 2 2 AC
2- 7 FLEGPA083CBKZ Leg holder l ass’y 1 1 1 1 AF
2- 7- 1 FAJS-A015CBKZ Adjustable leg ass’y 2 2 2 2 AE
2- 7- 2 LHLD-A533CBPZ Leg holder l 1 1 1 1 AL
2- 8 FLEGPA084CBKZ Leg holder r ass’y 1 1 1 1 AF
2- 8- 2 LHLD-A534CBPZ Leg holder r 1 1 1 1 AP
2- 13 DHNG-A437CBMZ Upper hinge ass’y 1 1 1 1 AE
2- 14 DHNG-A419CBMZ Bottom hinge r ass’y 1 1 1 1 AD
2- 15 DHNG-A418CBMZ Center hinge r ass’y 1 1 1 1 AE
2- 16 GCOV-A210CBFZ E.v cover 1 1 1 1 AR
2- 17 LCRA-A022CBPZ Fan clamp 1 1 1 1 AC
2- 19 LHLD-A389CBF0 Motor cushion 2 2 2 2 AF
2- 20 NFANPA011CBF0 Propeller fan 100 1 1 1 1 AD
2- 21 PSEL-C067CBEZ E.v cover sealer a 1 1 1 1 AA
2- 22 PSEL-C068CBEZ E.v cover sealer b 1 1 1 1 AA
2- 23 PSEL-C066CBEZ E.v cover sealer c 1 1 1 1 AC
2- 24 PCOVPA308CBFA Terminal cover 1 1 1 1 AE
2- 26 PCOV-A277CBFA R lamp cover 1 1 1 1 AE
2- 27 GCOVPA144CBRA R-c box cover 1 1 1 1
2- 28 HGRL-A210CBRA Fan louver 1 1 1 1 AU
2- 29 GCOV-A228CBFG Upper hinge cover - 1 - 1 AE
2- 29 GCOV-A228CBFH Upper hinge cover 1 - 1 - AE
2- 31 JKNB-A033CBFC R-temp.control knob 1 1 1 1 AC
2- 32 JKNB-A063CBFA V-tray control knob - 1 - 1 AC
2- 38 PGID-A161CBFZ R-air guider - 1 - 1 AG
2- 38 PGID-A168CBFZ R-air guider 1 - 1 - AK
2- 39 PGID-A162CBFZ R-air guider s - 1 - 1 AC
2- 43 LPLTPA323CBMA Panel base 1 - 1 - AN
2- 44 HGRL-A237CBFA F deodo.louver 1 1 1 1 AE
2- 45 HGRL-A238CBFA R deodo.louver 1 1 1 1 AC
2- 46 PFIL-A050CBEZ Deodorizer 2 2 2 2 AM
2- 47 LHLD-A672CBFZ Plasma holder 1 - 1 - AE
2- 49 LSTPPA108CBFA Chilled stopper 2 2 2 2 AC
2- 50 LSTPPA118CBFA Case stopper v 2 2 2 2 AC
2- 55 HGRL-A205CBFA Multi louver l - - 1 1 AM
2- 55 HGRL-A209CBFA Multi louver s 1 1 - - AM
2- 56 PFPFPB334CBFZ R-louver insu.l - - 1 1 AE
2- 56 PFPFPB345CBFZ R-louver insu.s 1 1 - - AE
2- 57 PSEL-C085CBEZ A-sealer r-louver - - 2 2 AC
2- 57 PSEL-C095CBEZ A-sealer r-louver 2 2 - - AB
2- 63 LHLD-A484CBFA Fan motor holder b 1 1 1 1 AH
2- 64 LHLD-A485CBFA Fan motor holder a 1 1 1 1 AH
2- 65 PSEL-B209CBE0 U-sealer handle 2 2 2 2 AB
2- 66 PSHEMA225CBPZ Heater cover 1 1 1 1 AC
2- 67 LPLTMA633CBPZ Drain support al 1 1 1 1 AF
2- 68 PSEL-A415CBE0 E.v cover sealer c 1 1 1 1 AC
2- 69 PSEL-C069CBEZ E.v cover sealer d 1 1 1 1 AA

28

SJ-P43N/43N
SJ-P47N/47N

REF. NO. PART NO. DESCRIPTION Q'TY CODE

SJ-P43N SJ-43N SJ-P47N SJ-47N

-SL -BE -SL -BE

2- 70 PSEL-C135CBEZ E.v cover sealer e 1 1 1 1 AC
2- 71 PSEL-A552CBE0 Dial sealer 1 1 1 1 AC
2- 72 PSEL-C078CBEZ A-sealer ag1 2 2 2 2 AC
2- 73 PSEL-C079CBEZ A-sealer ag2 1 1 1 1 AB
2- 77 LHLD-A359CBFA T-box holder 1 1 1 1 AE
2- 78 LPLTMA399CBP0 Dryer support 1 1 1 1 AD
2- 79 LBND-A019CBE0 Nylon band 1 1 1 1 AB
2- 80 PBOX-A132CBFA Terminal box 1 1 1 1 AF
2- 81 PBOX-A143CBFA Terminal box-b 1 - 1 - AH
2- 82 PCOVPA373CBFA Terminal cover-b 1 - 1 - AN
2- 83 PSEL-C080CBEZ A-sealer ag3 1 1 1 1 AA
2- 87 LBND-A018CBE0 Fastening band a 1 1 1 1 AP
2- 91 HGRL-A202CBFA F return cover 1 1 1 1 AF
2- 93 PCAP-A068CBFA C sliding cap a 4 4 4 4 AC
2- 94 PSEL-C137CBEZ E.v cover sealer f 1 1 1 1 AB
2- 95 PSHEMA231CBEZ Ev cover al a 1 1 1 1 AC
2- 98 LHLD-A504CBE0 Sl-3n clip 1 1 1 1 AD
2- 99 PSEL-A562CBE0 Leading wire sealer 1 1 1 1 AC
2- 100 PSEL-C138CBEZ E.v cover sealer g 1 1 1 1 AA
2- 101 PSEL-C139CBEZ Ev-insulation 47 2 2 2 2 AC

DOOR PARTS

3- 5 FDORFB832CBKZ F-door ass’y 1 - 1 - BS
3- 5 FDORFB839CBKZ F-door ass’y - 1 - 1 BS
3- 5- 1 LSTPPA131CBFA Fd-stopper spring r 1 1 1 1 AD
3- 5- 2 NBRGPA033CBFA Nylon bearing 3f - 1 - 1 AC
3- 5- 3 LSTPMA008CBM0 F-door stopper r 1 1 1 1 AD
3- 5- 4 GDAI-A071CBMZ Badge base - 1 - 1 AK
3- 5- 5 HBDGDA946CBEB Badge - 1 - 1 AN
3- 6 FPACGA346CBKZ F-door packing 1 1 1 1 AT
3- 7 HDECQA475CBMA Hd cap 2 2 2 2 AH
3- 8 HDECQA476CBRA Handle trim f 1 - 1 - AN
3- 8 HDECQA476CBRB Handle trim f - 1 - 1 AQ
3- 9 LPLTMA686CBPZ Hd support f 1 1 1 1 AD
3- 10 LPLTPA374CBFA Handle base f 1 1 1 1 AH
3- 11 HDECQA478CBMA Hd cover ft 1 1 1 1 AM
3- 15 FDORRB639CBKZ R-door ass’y - - 1 - BW
3- 15 FDORRB640CBKZ R-door ass’y 1 - - - BU
3- 15 FDORRB649CBKZ R-door ass’y - - - 1 BU
3- 15 FDORRB650CBKZ R-door ass’y - 1 - - BT
3- 15- 1 LSTPPA084CBFA Rd-stopper spring r 1 1 1 1 AD
3- 15- 2 NBRGPA022CBFA Nylon bearing 3s 1 1 1 1 AC
3- 15- 3 LSTP-A058CBM0 R-door stopper r 1 1 1 1 AF
3- 17 FPACGA347CBKZ R-door packing - - 1 1 AV
3- 17 FPACGA348CBKZ R-door packing 1 1 - - AV
3- 19 HDECQA477CBRA Handle trim r 1 - 1 - AN
3- 19 HDECQA477CBRB Handle trim r - 1 - 1 AR
3- 20 HDECQA479CBMA Hd cover rb 1 1 1 1 AP
3- 21 LPLTMA687CBPZ Hd support r 1 1 1 1 AD
3- 22 LPLTPA375CBFA Handle base r 1 1 1 1 AK
3- 30 GCOVPA177CBRA Panel cover 1 - 1 - BA
3- 31 HBDG-A005CBEA Pc badge 1 - 1 - AH

OTHER PARTS

4- 1 LBND-A023CBE0 L-band c 4 4 4 4 AC
4- 3 LX-VZA022CBZZ Special screw 8 8 8 8 AC
4- 11 QTAN-A012CBE0 Solderless term. b - 3 - 3 AH
4- 12 QTAN-A013CBE0 Solderless term. a 8 - 8 - AH
4- 15 LX-BZA090CBZZ Special screw 3 3 3 3 AC
4- 17 LX-WZA035CBZZ Washer 4 4 4 4 AB

ATTACHMENT PARTS

5- 1 UPOK-A180CBRA Bottle pocket 1 1 1 1 AR
5- 2 UPOKPA268CBFA R door pocket s 2 2 2 2 AH
5- 3 UPOK-A179CBRA Door pocket 3 3 3 3 AM
5- 4 UPOK-A181CBRA R door pocket 1 1 1 1 AL
5- 5 UTNA-A282CBFA Egg tray 1 1 1 1 AH
5- 6 FSRA-A193CBYZ Ice cube maker 1 1 1 1 AS
5- 9 USRA-A270CBFA Freezer tray 1 1 1 1 AT
5- 13 HGRL-A239CBFA Ventilating grille 1 - 1 - AN
5- 13 HGRL-A239CBFB Ventilating grille - 1 - 1 AN
5- 14 USRA-A268CBFA Evaporating pan 1 1 1 1 AM
5- 15 GGAD-A032CBFA V parting plate 1 1 1 1 AG
5- 16 UYOK-A401CBFA Vegetable case 1 1 1 1 AX
5- 17 UYOK-A399CBFA Ice storage box 1 1 1 1 AL
5- 18 UYOK-A400CBFA Fresh case 1 1 1 1 AV

29

SJ-P43N/43N
SJ-P47N/47N

REF. NO. PART NO. DESCRIPTION Q'TY CODE

1. MODEL NUMBER 2. REF. NO.

3. PART NO. 4. DESCRIPTION

HOW TO ORDER REPLACEMENT PARTS

To have your order filled promptly and correctly, please furnish the following information.

SJ-P43N SJ-43N SJ-P47N SJ-47N

-SL -BE -SL -BE

5- 19 GDORPA072CBRA Fresh door hs 1 1 1 1 AN
5- 24 FTNA-A394CBKZ R glass shelf ass’y 2 - 2 - AR
5- 24 USRA-A272CBFA Refrigerator tray - 2 - 2 AU
5- 24- 1 UTNA-A377CBEZ Glass shelf r 2 - 2 - AU
5- 24- 2 UWAKPA014CBFA G guard r 2 - 2 - AS
5- 25 FTNA-A395CBKZ V glass shelf ass’y 1 - 1 - AR
5- 25 USRA-A271CBFA Vegetable tray - 1 - 1 AW
5- 25- 1 UTNA-A378CBEZ Glass shelf v 1 - 1 - AW
5- 25- 2 UWAKPA015CBFA G guard v 1 - 1 - AS
5- 31 LRALPA136CBFA Ice tray holder l 1 1 1 1 AG
5- 32 LRALPA137CBFA Ice tray holder r 1 1 1 1 AG
5- 35 UPOKPA269CBFA Bottle stopper 1 1 1 1 AC

CYCLE PARTS

6- 1 PCMPLA220CBEZ Compressor 1 1 1 1 BW
6- 2 PSPAGA042CBE0 Rubber grommet 4 4 4 4 AE
6- 4 FFRM-A119CBKZ Base frame ass’y 1 1 1 1 AH
6- 5 FDRY-A006CBK0 Dryer ass’y 1 1 1 1 AX
6- 6 PCLI-A050CBE0 Clip 1 1 1 1 AD
6- 9 PSPAFA034CBE0 Sleeve 4 4 4 4 AD
6- 11 PPIPCA386CBEZ S.p connector 1 1 1 1 AF
6- 18 PPIPCA252CBE0 Charge pipe 2 2 2 2 AD
6- 19 FPIPCA172CBKZ Discharge p. ass’y 1 1 1 1 AM
6- 21 PCOVPA246CBE0 Terminal cover 1 1 1 1 AL
6- 24 PGUM-A004CBF0 Absorbent rubber a 2 2 2 2 AH
6- 25 QTAN-A045CBE0 Terminal block 1 1 1 1 AQ
6- 26 FPIPCA162CBKZ Eva pan pipe s ass’y 1 1 1 1 AS
6- 28 LANG-A058CBPZ Absorbent rubber clm 2 2 2 2 AC
6- 29 PGUM-A003CBF0 Absorbent rubber b 2 2 2 2 AH

MISCELLANEOUS

90- 1 TINS-A688CBRZ Operation manual 1 1 1 1
90- 2 TLAB-B042CBRZ Lamp label 1 1 1 1 AC
90- 3 SPAKCA184CBZZ Packing case 47n-f - - 1 1
90- 3 SPAKCA185CBZZ Packing case 43n-f 1 1 - ­ 90- 6 CPADBA799YDKZ Bottom pad ass’y 1 1 1 1 AV
90- 7 CPADBA057CBKZ Top pad ass’y 1 1 1 1 AR
90- 8 SPADBA190CBFZ Corner post fl 1 1 1 1 AK
90- 9 SPADBA191CBFZ Corner post fr 1 1 1 1 AL
90- 10 SPADBC435YDEZ Corner post bl 1 1 1 1 AG
90- 11 SPADBC436YDEZ Corner post br 1 1 1 1 AG
90- 15 TLAB-B055CBEZ R-door pocket label - - 1 1 AC
90- 21 TLAB-B009CBRZ Caution label rof 1 1 1 1 AE
90- 22 TLAB-A416CBR0 Warning label 1 1 1 1 AC
90- 24 TINS-A597CBRZ Caution sheet earth 1 1 1 1
90- 25 TINS-A366CBR0 Srv.station list 1 1 1 1 AC

30

SJ-P43N/43N
SJ-P47N/47N

A

B

C

D

E

F

G

H

A

123456

123456

B

C

D

E

F

G

H

DOOR PARTS

SJ-P43N/43N
SJ-P47N/47N

3-6

3-5

3-5-2

5-3

5-4

5-5

5-1

5-3

3-5-3
3-5-1

3-15-2

3-15-1

3-17

5-35

3-15

5-2

5-2

90-15

3-15-3

3-6

3-5

3-5-3
3-5-1

1-55

2-43

3-30

3-31

SJ-43N,47NSJ-P43N,P47N

3-5-4

3-5-5

3-8

3-10

3-11

3-9

3-20

3-7

3-7

3-19

3-21

3-22

31

SJ-P43N/43N
SJ-P47N/47N

A

B

C

D

E

F

G

H

A

123456

123456

B

C

D

E

F

G

H

CABINET PARTS

2-49

2-49

2-91

2-7

2-7-2

2-7-1

2-8

2-8-2

2-7-1

2-14

5-31

5-17

5-6

5-32

5-9

5-24

1-10

2-15

5-13

4-3

5-25

2-32

5-16

2-93

2-93

2-93

2-93

5-18

5-19

2-36

2-36

5-15

5-24-1

5-24-2

5-25-2

5-25-1

5-25

5-24

SJ-43N,47N

SJ-P43N,P47N

2-29

2-13

SJ-P43N/43N
SJ-P47N/47N

32

SJ-P43N/43N
SJ-P47N/47N

A

B

C

D

E

F

G

H

A

123456

123456

B

C

D

E

F

G

H

CABINET PARTS

2-95

2-94

6-11

6-28

6-1

2-87

2-31

6-9

6-2

4-17

1-2

6-4

1-9

2-80

2-98

2-24

6-18

6-5

6-18

4-11 (4-12)

2-78

2-66

2-67

2-4

1-21

1-22

6-21

4-15

2-2

6-26

2-72

1-4

2-83
2-73

2-71

2-38

2-39

2-79

1-3

2-27

2-46

2-45

1-7

2-50

1-8

90-2

2-57

2-56

2-55

2-26

2-63

2-19

1-6

2-19

2-64

2-20

2-17

2-21

2-22

2-68

1-17

4-1

1-5

1-1

1-20

2-65

4-1

2-23

2-16

2-28

6-19

6-6

6-25

2-46

2-44

5-14

6-29

2-70

2-69

2-99

6-24

2-100

2-101

2-82

1-50

2-81

(Only for SJ-P43N,P47N)

(Only for SJ-P43N,P47N)

2-47

1-45

1-46

(Only for SJ-43N,47N)

1-32

1-23

1-34

1-33

1-11

2-77

SJ-P43N/43N
SJ-P47N/47N

33

SJ-P43N/43N
SJ-P47N/47N

34

SJ-P43N/43N
SJ-P47N/47N

2005 SHARP CORP. (01K0.01E) Printed in Japan

43ATUF/ 43BTQF/ 47ATUF/ 47BTQF

COPYRIGHT © 2005 BY SHARP CORPORATION

ALL RIGHTS RESERVED.

No part of this publication may be repro­duced, stored in retrieval systems, or
transmitted in any form or by any means,
electronic, mechanical, photocopying, re­cording, or otherwise, without prior writ­ten permission of the publisher.