1
SJ-43L-A2
SJ-47L-A2
SERVICE MANUAL
S5219SE47JPS3
SHARP CORPORATION
TABLE OF CONTENTS
page
ENERGY LABEL................................................................................................................................................2
INSTALLATION .................................................................................................................................................2
CAUTIONS AND INFORMATIONS ...................................................................................................................3
SPECIFICATIONS .............................................................................................................................................4
THE FICHE ........................................................................................................................................................5
DESIGNATION OF VARIOUS PARTS ..............................................................................................................6
DIMENSIONS ....................................................................................................................................................7
LIST OF ELECTRICAL PARTS .........................................................................................................................9
WIRING DIAGRAM..........................................................................................................................................10
FUNCTIONS ....................................................................................................................................................12
ASSEMBLING PROCEDURES OF MAIN PARTS AND CAUTIONS ..............................................................15
COOLING UNIT ...............................................................................................................................................21
REPLACEMENT PARTS LIST ........................................................................................................................23
Refrigerant; HFC-134a
Refer to "HFC-134a COOLING UNIT" Service Manual for handling this refrigerant.
DESTINATION .........................3
In the interests of user-safety (Required by safety regulations in some
countries) the set should be restored to its original condition and only
parts identical to those specified should be used.
REFRIGERATOR-FREEZER
MODELS
SJ-43L-
A2G/A2S/A2A
SJ-47L-
A2G/A2S/A2A
SJ-43L SJ-47L
This equipment complies with the
requirements of Directives
96/57/EC, 89/336/EEC and 73/23/EEC
as amended by 93/68/EEC.
2
SJ-43L-A2
SJ-47L-A2
INSTALLATION
Free standing type
To ensure adequate ventilation for this refrigerator, install with 6 cm space at the rear and both sides, with a
minimum space of 9 cm above the refrigerator.
This refrigerator shall be used under the ordinary place condition between +5˚C and +38˚C of ambient
temperature, and also not be left under -10˚C for long days.
To be used this refrigerator within the range of the rated voltage+6%
Usage of "the ENERGY LABEL"
When displaying this refrigerator in the shop-window, attach the
"ENERGY LABEL" to it in the following procedure.
"ENERGY LABEL (DATA)"
(This label is in Operation manual)
"ENERGY LABEL (BASE)"
of each language
Refrigerator
Data part
E
B
A
C
D
E
G
F
G
Fix the data part of
"ENERGY LABEL (DATA)"
on the data part of
"ENERGY LABEL (BASE)"
6cm
6cm
9cm
ENERGY LABEL
3
SJ-43L-A2
SJ-47L-A2
Some household cleaning chemicals may affect the internal
food liner and plastic parts resulting in splitting or cracks
occurring.
When cleaning all plastic parts inside this refrigerator, only
use diluted dishwashing liquid(soapy water). Make sure that
all plastic parts are thoroughly rinsed with water after cleaning.
CAUTIONS AND INFORMATIONS
1. Some foods freezed in the refrigerator compartment.
2. Some plastic parts were cracked or splitted.
Cracking or crunching sound;
Sound produced by expansion and contraction of inner walls and internal parts during cooling.
Squeaking sound;
Sound produced by expansion and contraction of internal parts.
Sound of flowing fluid (gurgling sound, fizzing sound);
Sound of refrigerant flowing in pipes (sound may become louder from time to time).
3. IT IS NORMAL for the refrigerator to produce the following sounds.
Do not place food directly in front of
cold air outlet.
This may lead to the food freezing.
IN
OUT
cold air flow
In case of following troubles, the cause is not related with the failure of refrigerator.
Please mention the correct way to the customer for the use of refrigerator when the repairing.
4
SJ-43L-A2
SJ-47L-A2
SPECIFICATIONS
Items SJ-43L-A2 SJ-47L-A2
Type 2-Door 2-Door
Outer dimensions Height 1700mm(66.9") 1820mm(71.7")
(Including spacer) Width 680mm(26.8") 680mm(26.8")
Depth 660mm(26.0") 660mm(26.0")
Rated storage volume 347 liter (12.3cu.ft) 384 liter (13.6 cu.ft)
(Rated volume) F: 99liter (3.5 cu.ft) F: 99 liter (3.5 cu.ft)
R: 248 liter(8.8 cu.ft) R: 285 liter(10.1 cu.ft)
Gross volume 370 liter (13.1cu.ft) 407 liter (14.4 cu.ft)
F: 107liter (3.8 cu.ft) F: 107 liter (3.8 cu.ft)
R: 263 liter(9.3 cu.ft) R: 300 liter(10.6 cu.ft)
Defrosting System Heater system
Start Automatic
Finish Automatic
Temperature control Automatic (Adjustable)
No-frost freezer Yes
Interior lamp 1
Caster 2
Evaporating pan 1
Refrigerator Refrigerator tray 2
Compartment Vegetable tray 1
Vegetable case 1
V parting plate 1
R door pocket 1
Egg tray 1
R door pocket S 2
Bottle pocket 1
Bottle stopper 1
Door pocket 1
Fresh case 1
Freezer Freezer tray 1
Compartment Ice cube maker Twin ice cube maker
Ice storage box 1
Door pocket 2
Deodorizing unit 2 ( Honeycomb type)
RATING
Items SJ-43L-A2 SJ-47L-A2
Rated voltage (V~) 220-240
Rated frequency (Hz) 50
Climate class ST
Rated current (A) 1.2-1.3
Rated input (W) 115-120
Rated input of heating elements (W) 128-152
Refrigerant (Charging quantity) HFC-134a(105g)
Net Weight (kg) 66 68
PLUG TYPE
Plug cord 3 Wires
Plug type CS
Destination mark 3
COLOR
Items -A2G -A2S -A2A
Outside color Gray Silver Beige
Inside color White
Hole
5
SJ-43L-A2
SJ-47L-A2
DESIGNATION OF VARIOUS PARTS
Upper hinge cover
Hot pipe
Freezer temp. control knob
Hot pipe
Ventilating grille
Adjustable leg ass'y
Fan motor
Defrost thermostat
Evaporator
Defrost heater
Damper thermostat
Refrigerator temp. control knob
Drain pipe
Vegetable case
Compressor
Starting relay, Overload relay(Protector)
Caster
Freezer
compartment
Refrigerator
compartment
Mark: Cold air flow
Evaporating pan
Defrost timer
Figure D-1. External Description
Figure D-2. Constructions
1
2
3
4
5
5
7
8
9
11
10
12
13
14
15
17
16
18
19
20
21
23
24
22
25
26
20
21
6
1. Freezer temp. control knob
2. Freezer shelf(Freezer tray)
3. Ice cube maker
4. Ice cube box(Ice storage box)
5. Deodorizing unit
6. Fresh case
7. Refrigerator temp. control knob
8. Light(Lamp)
9. Refrigerator shelf(Refrigerator tray)
10. Lever
11. Shelf(Vegetable tray)
12. Vegetable crisper(Vegetable case)
13. Separator plate(V parting plate)
14. Evaporating pan
15. Casters
16. Ventilating grille
17. Adjustable feet(Adjustable leg ass'y)
18. Fan switch
19. Fan & light switch
20. Utility pocket(Door pocket)
21. Magnetic door seal(Door packing)
22. Egg holder(Egg tray)
23. Egg pocket(R door pocket)
24. Small pocket(R door pocket S)
25. Bottle guard(Bottle stopper)
26. Bottle pocket
NOTE : 2 star section for storing
frozen food only. (not freezing)
The names are the denominations used in the
REPLACEMENT PARTS LIST.
6
SJ-43L-A2
SJ-47L-A2
1
NO.
2
3
4
5
6
8
9
11
12
13
14
Trade mark
Items
Description
Remarks
Model name
Type
Energy efficiency class
Eco-award mark
Energy consumption
(220V 50Hz at 25 C)
Star rating of frozen food
compartment
Temperature rise time
Freezing capacity
Climate class
Noise
10 No frost
7
Net storage volume of frozen
food storage compartment
SJ-43L
Category; 7
B
ST ST
39 dB(A)
re 1 pw
39 dB(A)
re 1 pw
510
kWh/year
708
kWh/year
744
kWh/year
248 L
No frost
9 h
6.0 kg /24h
Net storage volume of fresh
food storage compartment
SJ-47L
Category; 7
B
560
kWh/year
285L
9 h
6.0 kg /24h
880/92
EN153
86/594/EEC
No frost
THE FICHE (according to ANNEX : 94/2/EC)
15
Maximum allowable electricity
consumption (Emax)
(96/57/EC)
88 L
4-STAR
88 L
4-STAR
2-STAR
2-STAR
11 L
11 L
E max
(2.04)(1.94) (kWh/day)
fridge / freezer
A~G
7
SJ-43L-A2
SJ-47L-A2
DIMENSIONS
OUTER DIMENSIONS AND CLEARANCE
Fig. E-1(SJ-43L)
Fig. E-2(SJ-47L)
680
680
470
660
90
more than
60
more than
60
more than
60
more than
5951022.5
1700
73
16 9.5
1260
1320
1210
(Unit : mm)
1
1: Include the badge
Not include the handle
90
more than
660
60
more than
680
5951142.5
1820
680
470
60
more than
60
more than
73
16
9.5
1260
1320
1210
(Unit : mm)
1
1: Include the badge
Not include the handle
8
SJ-43L-A2
SJ-47L-A2
INNER DIMENSIONS
The dimensions between shelves can be changed by setting the shelves on the other rails.
Fig. E-3(SJ-43L)
Fig. E-4(SJ-47L)
(Unit: mm)
502
321
502
502
502
518
531
524
524
526
242
242
510
225
232
89
89
112
99
99
246
269
269
320
188
229
210
118
(218.5)
(175)
(185)
226
126
82
526
628.5
502
502
502
321
531
524
524
502
518
242
242
510
526
225
232
89
89
112
99
99
246
269
269
320
188
229
210
118
(168.5)
(125)
(165)
226
126
82
526
508.5
(Unit: mm)
9
SJ-43L-A2
SJ-47L-A2
LIST OF ELECTRICAL PARTS
ITEMS TYPE NAME RATING SPECIFICATIONS
Thermostat MM1-8149 125V 6A (At normal notch)
250V 3A ON/OFF : -20 / -25˚C
Defrost thermostat S101 250V 8A Open/Close : 8 / 1˚C
Thermo. fuse SF70E 250V 10A Working temp. : 70˚C
Fan motor 3R00121A 220-240V 50/60Hz Working with ø100 fan
Defrost heater MM6-4264 220-240V 378Ω 140W at 230V
Door switch DSD-5 250V 0.25A 4 terminals push-button type
Damper thermostat MM1-6173 — Open/Close : 5 / 0˚C
Defrost timer ND1004M2 220-240V Integration type
50/60Hz Cycle time : 10h44m/8h57m(50/60Hz)
Delay time : 4m20s/3m37s(50/60Hz)
Lamp socket — 250V 1A E-12(Hard plastic body type)
Lamp — 240V 15W E-12
Compressor FL1568SD 220-240V/50Hz Cooling capacity : 188W (50Hz)
Main coil : 13.3Ω
Aux. coil : 25.6Ω
(at 25˚C)
Starting relay PET0SAT — 22 Ω 300V
Overload relay(Protector) 1.8C36A1 — Open/ Close : 130/60˚C
Running capatior — 420V or 450V 4µF—
Common
Main coil
Aux. coil
10
SJ-43L-A2
SJ-47L-A2
WIRING DIAGRAM
Be sure to replace the electrical parts with specified ones for maintaining the safety and performance of the set.
E
CONNECTED IN TERMINAL BOX
CONNECTOR
GY
BR
OR
Y
R
P
BL
BK
SB
G-Y
W
: GRAY
: BROWN (live)
: ORANGE
: YELLOW
: RED
: PINK
: BLUE(neutral)
: BLACK
: SKY-BLUE
: GREEN-YELLOW (earth)
: WHITE
F-Thermostat
(R)
Defrost timer
TM
Thermo.
fuse
FM
Defrost
heater
Defrost
thermo.
Starting relay
C
M
A
Compressor
Protector
(BL)
Door switch
Source
Plug
(SB)
Fan motor
L
(OR)
(BR)
(W)
(Y)
(GY)
(BK)
Lamp
Running capacitor
Figure W-1. Wiring Diagram
11
SJ-43L-A2
SJ-47L-A2
Figure W-2. Electric Accessories Layout
Cabinet ass'y
E.V. cover ass'y
Lead EV-cover ass'y
Fan motor
F-thermostat
Def thermo. ass'y
Fuse ass'y
FM
Def. heater ass'y
Door switch
2 (PUSH OPEN)
3 (PUSH CLOSE)
4 (PUSH OPEN)
1 (NEUTRAL)
1
2
121
2
121
2
3
4
1
2
3
4
1
2
3
4
1
L
E
N
1
5
2
6
3
7
4
8
1
5
2
6
3
7
4
8
GY-1
OR-1
R-1
BR-1
Y-1
W-1
BL-1
BL-2
BR-2
SB-1
(SB-1)
BK-1
(W-1)
Y-2
(OR-1)
R lamp box ass'y
Lamp 15W
Lamp socket
L
Terminal box
TM
Defrost timer
(Y-1)
(Y-2)
(R-1)
(BK-1)
GY-2
Terminal block
Protector
Compressor
C
M
A
Starting
relay
Source cord
BROWN
BLUE
GRAY
EARTH
G
BR
OR
Y
R
P
BL
BK
SB
G-Y
W
: GRAY
: BROWN (live)
: ORANGE
: YELLOW
: RED
: PINK
: BLUE (neutral)
: BLACK
: SKY-BLUE
: GREEN-YELLOW (earth)
: WHITE
Running capacitor
12
SJ-43L-A2
SJ-47L-A2
FUNCTIONS
1. ADJUSTABLE TEMPERATURE CONTROL
(1) Temperature control of freezer
Thermostat (senses freezer temperature) operates on ON/OFF switchover to control the compressor and
cool air circulating fan , and allows the freezer temperature to keep at a suitable temperature.
However adjust the freezer temp. control knob as follows depending upon the storing condition of foods.
The values shown above refer to the measurement carried out center area and 1/3 of overall height from the bottom
at each of the refrigerator and the freezer after machine has been operated at an ambient temperature of 30˚C with no
food stored and the door closed until the temperature is stabilized.
The values vary depending upon frequency of opening and closing the door, ambient temperature, amount of stored
foods and manner of storing foods.
Figure F-2.
NOTE: The refrigerator temperature is affected also by the freezer temperature. If the freezer temp.
control knob is set at the position "MAX", the temperature tends to be lower than the following
values, and if set at near the position "MIN", temperature tends to be higher.
If the refrigerator is operated for a long time with the freezer temperature control sets the "MAX"
position, foods stored in the refrigerator compartment may also freeze.
When refrigerator temperature control sets to the "Coldest", some foods stored may freeze.
In this case adjust control set back to the "MED" position.
When refrigerator temperature control sets to the "Coldest", some foods stored in Fresh case may
also become frozen.
(3) Reference value of temperature
Figure F-1. 2 star section for storing frozen food only.(not freezing)
(2) Temperature control of refrigerator
Damper-thermostat senses temperature of the refrigerator and changes the opening angle of the damper
automatically.
However, as the Damper-thermostat has no function to switch on or off the compressor and fan motor, the
freezer temperature control causes temperature in the refrigerator to vary to some extent.
However, adjust the refrigerator temp. control knob as follows depending upon the cooling condition.
KNOB
SETTING
MAX
(Coldest)
MIN
PURPOSE
For making ice rapidly or fast freezing.
For storing frozen food for a short period (up to one month).
When frozen food or ice cream is not stored.
For normal freezing.
MED
When restocking with fresh food.
KNOB
SETTING
MED
Coldest
MIN
PURPOSE
For keeping freshness of food longer.
For normal operation.
When the refrigerator provides excessive cooling.
When the refrigerator does not provide sufficient cooling.
SETTING OF
REFRIGERATOR TEMP.
CONTROL KNOB
Refrigerator
temperature
Fresh case
temperature
Coldest MED MIN
Approx.
0˚c
Approx.
-3˚c
Approx.
3˚c
Approx.
1˚c
Approx.
6˚c
Approx.
4˚c
The values shown above refer to the case where the
freezer temp. control knob is set at "MED".
SETTING OF
FREEZER TEMP.
CONTROL KNOB
Freezer
temperature
2 star section
temperature
MAX
(Coldest)
MED MIN
Approx.
-21 C
-15 C -12 C -9 C
Approx.
-18 C
Approx.
-15 C
13
SJ-43L-A2
SJ-47L-A2
(2) Where is melted frost brought
1. Melted frost is brought into the evaporating
pan at the back of the set and is evaporated
here by the heat of compressor.
2. Be sure to use Evaporating pan as inserted
so as to be level with the outer case.
2. DEFROSTING
(1) No defrosting operation is necessary
No defrosting operation is necessary.
As this machine is so designed that a built-in
evaporator cools air and a fan circulates cooled
air, neither the freezer nor the refrigerator is
frosted, though the evaporator is frosted.
The frosted evaporator is defrosted automatically
due to the function of defrosting timer and heater,
requiring no defrosting operation.
(3) The following circuit diagrams in the table show automatic defrosting function of the refrigerator with
timer and defrost thermostat.
Operation Electric diagram Description
1. Cooling
(Normal)
2. Defrosting
(Time 20 to 30 min.)
3. Drain
(Time approx. 5 min.)
4. Restart
(Time approx. 5 min.)
The integration timer integrates running
time of the compressor. When it reaches
cycle time of defrost timer, the timer
contact is changed to start defrosting.
When the defrost thermostat becomes
OFF, the timer motor starts running.
During the operation time (delay time
of defrost time)
defrosted water is
drained outside the refrigerator.
Timer contact is changed to cooling
operation and the compressor starts
running and the timer motor stops.
Defrost thermostat contact becomes ON
when it’s cooled. And the timer motor
starts running. (Figure F-3.)
Figure F-3.
Figure F-4 .
Figure F-5.
Figure F-6.
TM COMP
Defrost thermostat ON Compressor running
Timer motor running
Timer contact
Defrost
thermostat (ON)
Defrost heater
Thermo. fuse
Compressor
Timer motor
SOURCE
TM COMP
Defrost thermostat OFF Compressor running
Timer motor stops
Thermostat Timer contact
Defrost
thermostat (OFF)
Defrost heater
Thermo. fuse
Compressor
Timer motor
SOURCE
TM COMP
Defrost thermostat OFF Compressor stops
Timer motor running
Thermostat Timer contact
Defrost
thermostat (OFF)
Defrost heater
Thermo. fuse
Compressor
Timer motor
SOURCE
TM COMP
Defrost thermostat ON Compressor stops
Timer motor stops
Thermostat Timer contact
Defrost
thermostat (ON)
Defrost heater
Thermo. fuse
Compressor
Timer motor
SOURCE
Thermostat
The timer contact is changed to start
defrosting, the timer motor stops, and
power is supplied to the defrost heater.
It takes about 20 to 30 min. to defrost.
When little frosted, the defrosting takes
little time. When much frosted, the defrosting takes much time.
14
SJ-43L-A2
SJ-47L-A2
(4) As a reference to determine the causes of trouble, malfunction and phenomena are described below.
Refer to the following when repairing.
1. Disconnection of defrost heater
As off-cycle defrosting is performed, the defrosting time is extremely prolonged. Each time defrosting is
started, the freezer temperature rises and a portion of ice and stored foods are melted.
2. Melted thermo. fuse or opened-circuit due to the defect of defrost thermostat.
When the above mentioned trouble occurs in cooling operation, the timer motor does not run, defrosting
will not take place, and consequently freezing is caused. In the above mentioned condition, when the timer
shaft is turned by hand to defrost, the timer motor runs during the operation time. However, the motor stops
from the time when the contact is changed, and freezing causes.
NOTE:
As the thermo. fuse assembly is intended to prevent dangers, do not use it under shorted condition even
for a short period.
3. DEW PREVENTION
The hot pipe, namely D.P.-condenser, is arranged around the flange part of
cabinet and the C-partition plate, preventing dew from being generated on
the cabinet.
NOTE:
D.P.-condenser pipe may be felt hot if touched by hand while the
compressor is in operation.
If you are asked about this, please explain that the hot pipe serve to
prevent the dew generation.
Figure F-7
4. INSPECTION OF INITIAL STARTING
(1) Inspection of cooling unit
1. Set the temperature control knob to "MAX" and check that the compressor starts to operate.
2. Depress the door switch to run the fan and check that cool air is blown out of the cold air outlet of the
freezer and the refrigerator.
3. When the compressor does not work, check that the timer is not set to "defrost" position.
4 It takes about an hour and a half or two hours to put food in the refrigerator after starting operation.
NOTE:
After return the temperature control knob to "MED" position.
When the refrigerator is operated initially after installed, the compressor may vibrate excessively for 1 to 2
min. However, vibration becomes normal if it is continuously operated.
(2) Inspection of defrost device
Operate the refrigerator for 20 to 30 min. and then check the defrost device in the following procedures :
Allow 5 min. to restart the compressor since immediate starting after stopping will cause unsmooth operation.
1. Turn the timer shaft clockwise with a screw driver.
At this time, make certains the timer clinks and the compressor stops.
2. After more than 5 min., turn the shaft further to operate.
Make certain cooling operation is started again.
Hot pipe
15
SJ-43L-A2
SJ-47L-A2
ASSEMBLING PROCEDURES OF MAIN PARTS AND CAUTIONS
CAUTION: DISCONNECT THE UNIT FROM THE POWER SUPPLY BEFORE ANY REPAIRING.
1. R-AIR GUIDER ASSEMBLY
Figure A-1
After forming, fix it to the refrigerator.
Stick thermo.
cap. sealer
Less than 160 mm
Damper
thermostat
5
1
mm
8
1
mm
Less than 12 mm
10 2 mm
NOTE
Minimum bending radius is R5mm.
There should be no gas leak by reforming of sensor tube.
+
++
Figure A-2
(1) Forming sensor of Damper thermo.
Damper thermo.
Thermo. cap. sealer
A-sealer ag3
A-sealer ag2
Dial sealer
R air guider
R air guider S
A-sealer ag1
(2) Setting R air guider S and sticking sealers to R air guider.
R air guider
R air guider S
A-sealer ag1A-sealer ag1
Masking tape
A-sealer ag3
A-sealer ag2A-sealer ag2
Dial sealer
R air guider
A-sealer ag1
A-sealer ag1
OVERLAP AREA
OVERLAP 8mm
OVERLAP 15mm
OVERLAP 15mm
DATUM
DATUM
DATUM
Figure A-3
16
SJ-43L-A2
SJ-47L-A2
(2) Fixing of Fan motor and Fan
(2)-1 Stick U-sealer handle to Fan motor holder A.
Figure A-6
2. FAN LOUVER AND E.V COVER ASSEMBLY
Figure A-4
E.v cover sealer C
E.v cover
sealer C
Fuse ass’y
F-thermostat
E.v cover
Defrost thermo.
ass’y
E.v cover
sealer A
E.v cover
sealer G
L-band C
L-band C
Lead EV-cover
ass’y
U-sealer
handle
Fan motor
holder A
Fan clamp
Propeller fan
100
Fan motor holder B
Fan motor
Motor cushion
E.v cover
sealer B
E.v cover sealer D
E.v cover sealer E
Fan motor holder A
U-sealer handle
U-sealer handle
7 2mm
+
+
0 1mm
C
C
SEC. C-C
E.v cover sealer C
E.v cover sealer G
E.v cover sealer A
E.v cover sealer B
E.v cover
[back side]
STICK START
STICK START
STICK START
(1)
(1)
(2)
(3)
Screw
Fan louver
Screw
Claw
Claw
Claw
Claw
2-1. How to remove the Fan louver
(1) Take out 2 screws.
(2) Insert the screwdriver into the air hole of the Fan
louver.
(3) Press the Fan louver to the left side with the
screwdriver,and pull it toward yourself to take off the
Fan louver.
2-2. E.v cover assembly
(1) Sticking of Sealers to E.V cover
Figure A-5
Figure A-7
17
SJ-43L-A2
SJ-47L-A2
(2)-4 Set Fan clamp to Propeller fan 100 and insert
it to the shaft of Fan motor.
(2)-2 Insert the terminals of Lead EV-cover ass'y to
Fan motor.
(2)-3 Fix two Motor cushions to Fan motor, and set it
at Fan motor holder A and B.
Then fix with Tapping screw.
Figure A-8
(3) Setting of Fan motor ass'y , Defrost thermo. ass'y and Fuse ass'y.
Fan motor
holder A
Fan motor
holder B
Motor cushion
Tapping
screw
Fan motor
Lead EV-cover ass’y
RED
BROWN
Fan clamp
Propeller
fan 100
Fan clamp
Slit
Slit of each Fan clamp
and Propeller fan
should not be at same position.
Shaft
4 0.5mm
+
Detail of D
D
Note
Propeller fan should not be
taken out from shaft when
pulled by 3 kgf.
Figure A-10
[front side]
more than 3.5mm more than 3.5mm
Lead e.v cover
ass’y
E.v cover sealer C
Take out lead wire
from square hole to
front and fix with
L-band C, then seal
with E.v cover sealer C
Aluminum tape
Aluminum tape
Aluminum tape
Aluminum tape
Tapping screw
Set metal side below
L-band C
L-band C
L-band C
Fuse ass’y
[back side]
Defrost thermo.
ass’y
Tapping screw
E.v cover
F
G
F
H
H
Defrost thermo.
ass’y
CUT
Not come out of claw.
10 5mm
+
SEC. F F
Turn up lead wire
ATTENTION
SEC. H H
Fuse ass’y
E.v cover
sealer E
Detail of G
E.v cover sealer E
[Front side]
Figure A-9
18
SJ-43L-A2
SJ-47L-A2
50mm
8.5mm
21mm
R10mm
R10mm
(5) Setting of F-thermostat
(5)-1 Form capillary tube of F-thermostat.
Note
• Bending radius of
capillary tube should be
from R5mm to R10mm.
Figure A-13
(5)-3 Set to E.V cover.
Stick E.v cover sealer D.
(5)-2 Insert terminal of Lead EV-cover ass'y.
After inserting, fix with vinyl tape.
Figure A-11
1234
5678
F-thermostat 2
F-thermostat 6
(BROWN, inserted)
Fuse 8 (BLACK)
Fuse 8 (WHITE)
Fan motor 1 , 5
(RED, inserted)
Defrost thermo. 3 (PINK)
Defrost thermo. 7 (BLUE)
WIRE COLOR FOR FAN MOTOR
100-110V : WHITE
127V : YELLOW
220-240V : BLUE
Note Pins should be inserted surely,
and check by pulling it.
Figure A-12
Vinyl tape
Figure A-14
Figure A-15
RED
BROWN
(front side)
(back side)
F-thermostat
SEC. B B
B
B
E.v cover sealer D
(4) Inserting of pins
19
SJ-43L-A2
SJ-47L-A2
Fig. A-16
(1)-2. As shown in Fig. A-17, pull the upper part of
Evaporator toward you, pull it diagonally so that
the pipe of Evaporator does not contact the convex
part of food liner.
3. DEFROST HEATER
(1) Taking-out Evaporator
(1)-1. Take out E.v cover ass'y (Fig. A-16).
Evaporator
Food liner convex part
Food liner convex part
Evaporator
Pipe
Fig. A-17
(1)-3. As shown in Fig. A-18, bend the removed
Evaporator horizontally so that Defrost heater can
be replaced easily.
NOTE: When pulling Evaporator and bending the
pipes, pay attention so as not to break and
deform the pipes. Still, take care not to hurt
yourself by fin of Evaporator.
Fig. A-18
Evaporator
(2) Replacement of Def. heater ass'y.
(2)-1 Remove the center screw of Drain support al
to take it off from the food liner.
Fig. A-19
(2)-2 Raise the protrusion part of Drain support al.
Then remove Heater cover.
Fig. A-20
(2)-3 Open Def.heater fixed part of Drain support al to
the right and left, then remove Def.heater ass'y.
Screw
Drain support al
Drain support al
Heater cover
Protrusion parts
Protrusion part of Drain support al(2 pcs.)
Heater cover
Def. heater ass’y
Fig. A-21
Fixed parts
Drain support al
Def.heater ass’y
20
SJ-43L-A2
SJ-47L-A2
Fig. A-26
(2)-9. Wind up Leading wire sealer as shown in Fig. A-27
Fig. A-25
(2)-8. Set Heater cover on Drain support, and bend top
edge c and d to outside as shown in Fig. A-26.
Fig. A-23
(2)-6. Bend a and b of Drain support al to right angle
(90˚) to set Def. heater ass'y. (Fig. A-24)
Fig. A-22
(2)-5. Wind the Glass cloth tape (3M: No. 27) to lead wire
of Def. heater ass'y. (2 places)
(2)-4. Replace Def. heater ass'y with new one. (2)-7. Stick the longer wire to the Drain support by
aluminum tape (2 pieces), and wind vinyl tape
(2 pieces) to lead wires of Def. heater ass'y by
aluminum tape as shownin Fig. A-25.
Note: Glass cloth tape part shall be both side of Drain
support to protect the lead wire from damaged.
Fig. A-24
Heater cover
Def.heater ass’y
Drain support al
Def. heater ass’y
Glass cloth tape
(W40 x L25)
Glass cloth tape
Wind the Glass cloth tape
more than 2 turns.
360
(40)
(40)50
Lead wire
+
+
5
5
Drain support al
This side is longer wire
This side is shorter wire
Def.heater ass’y
a
b
Glass cloth tape
Glass cloth tape
Glass cloth tape
Glass cloth tape
aluminum tape
(more than 2 turns)
[back side]
[bottom side]
A
A
Sec. AA
(W25 X L40)
Fig. A-27
(2)-10
. Set the assembly above on the food liner by fixing
a screw.
top edge
Drain support al
Heater cover
Heater cover
Def.heater ass’y
Def.heater ass’y
c
d
Sec. BB
B
B
Drain support al
Heater cover
Def.heater ass’y
190 20
+
Leading wire sealer
21
SJ-43L-A2
SJ-47L-A2
COOLING UNIT
Figure C-1. Cooling unit
Hot pipe L
(Side condenser)
Hot pipe
(DP-condenser)
Hot pipe R
(Side condenser)
Evaporator
Suction pipe
Compressor
Capillary tube
Dryer
Back condenser
Mark: Refrigerant flow
Mark: Brazing portion
Eva-pan pipe
(3) Installing of Evaporator
(3)-1. Install Evaporator as shown in Fig. A-16 in the
reverse order of Fig. A-17.
(3)-2. Correct the deformed fin.
NOTE
1. When installing Evaporator, take care not to
deform significantly and break the pipes.
2. Take care not to damage the lead wires and hurt
yourself by the fin of Evaporator.
22
SJ-43L-A2
SJ-47L-A2
From Suction pipe
to SP connector
From Compressor
to Charge pipe
From Dryer
to Capillary tube
From Discharge p connector
to Eva-pan pipe ass’y
From SP connector
to Compressor
From Compressor
to Discharge p connector
From Eva-pan pipe ass’y
to Back condenser In
From Back condenser out
to Hot pipe
From Hot pipe
to Dryer
Figure C-3. Location
Figure C-2. Location
Compressor
Suction pipe
Charge pipe
Charge pipe
Capillary tube
Dryer
Hot pipe
S.P. connector
Eva-pan pipe
Back condenser
Evaporator
23
SJ-43L-A2
SJ-47L-A2
REF. NO. PART NO. DESCRIPTION Q'TY CODE
REPLACEMENT PARTS LIST(SJ-43L-A2G/A2S/A2A)
SJ-43L SJ-43L SJ-43L
-A2G -A2S -A2A
ELECTRIC PARTS
1-1 RTHM-A103CBZZ F-themostat 1 1 1 AV
1-2 RSTT-A134CBE0 Starting relay 1 1 1 AS
1-3 QSWTDA047CBZZ Defrost timer 1 1 1 AZ
1-4 PDMP-A050CBEZ Damper thermo 1 1 1 AW
1-5 FTHM-A039CBKZ Defrost thermo.ass'y 1 1 1 AM
1-6 RMOTRA046CBE0 Fan motor 1 1 1 AZ
1-7 QSOCAA084CBEZ Lamp socket 1 1 1 AL
1-8 RLMP-A029CBEZ Lamp15w 1 1 1 AH
1-9 QACC-A142CBZZ Source cord 1 1 1 AQ
1-10 QSW-PA090CBZA Door switch 1 1 1 AS
1-11 RHOG-A161CBZZ Protector 1 1 1 AX
1-17 FFS-TA061CBKZ Fuse ass'y 1 1 1 AM
1-20 FW-VZA146CBEZ Lead ev-cover ass'y 1 1 1 AL
1-21 FHETBA161CBEZ Def.heater ass'y 1 1 1 AY
1-22 FCNW-A688CBKZ Relay cord s ass'y 1 1 1 AR
1-23 QCNW-A671CBE0 Reray wire rc 1 1 1 AD
1-32 RC-EZA199CBZZ Running capacitor 1 1 1 AT
1-33 QCNW-A886CBE0 Olr cord 1 1 1 AE
MECHANICAL PARTS
2-2 JKNB-A036CBFC F-temp. control knob 1 1 1 AC
2-4 LHLD-A489CBFA E.v. holder 2 2 2 AD
2-7 FLEGPA083CBKZ Leg holder l ass'y 1 1 1 AF
2-7-1 FAJS-A015CBKZ Adjustable leg ass'y 2 2 2 AE
2-7-2 LHLD-A533CBPZ Leg holder l 1 1 1 AL
2-8 FLEGPA084CBKZ Leg holder r ass'y 1 1 1 AF
2-8-2 LHLD-A534CBPZ Leg holder r 1 1 1 AP
2-13 DHNG-A417CBMZ Upper hinge ass'y 1 1 1 AE
2-14 DHNG-A419CBMZ Bottom hinge r ass'y 1 1 1 AD
2-15 DHNG-A418CBMZ Center hinge r ass'y 1 1 1 AE
2-16 GCOV-A210CBFZ E.v cover 1 1 1 AR
2-17 LCRA-A010CBE0 Fan clamp 1 1 1 AD
2-19 LHLD-A389CBF0 Motor cushion 2 2 2 AF
2-20 NFANPA011CBF0 Propeller fan 100 1 1 1 AD
2-21 PSEL-C067CBEZ E.v cover sealer a 1 1 1 AA
2-22 PSEL-C068CBEZ E.v cover sealer b 1 1 1 AA
2-23 PSEL-C066CBEZ E.v cover sealer c 1 1 1 AC
2-24 PCOVPA308CBFA Terminal cover 1 1 1 AE
2-26 PCOV-A277CBFA R lamp cover 1 1 1 AE
2-27 GCOVPA142CBRA R-c box cover 1 1 1 AQ
2-28 HGRL-A206CBRA Fan louver 1 1 1 AS
2-29 GCOV-A209CBFA Upper hinge cover 1 - - AC
2-29 GCOV-A209CBFB Upper hinge cover - 1 - AC
2-29 GCOV-A209CBFE Upper hinge cover - - 1 AD
2-31 JKNB-A033CBFC R-temp.control knob 1 1 1 AC
2-32 JKNB-A063CBFA V-tray control knob 1 1 1 AC
2-36 PCAP-A006CBFX Screw cover 2 - - AB
2-36 PCAP-A006CBFY Screw cover - - 2 AB
2-36 PCAP-A077CBFA Screw cover - 2 - AA
2-38 PGID-A161CBFZ R-air guider 1 1 1 AG
2-39 PGID-A162CBFZ R-air guider s 1 1 1 AC
2-41 PSEL-B848CBEZ A-sealer thermo.cap 1 1 1 AC
2-44 HGRL-A203CBRA F deodo.louver 1 1 1 AF
2-45 HGRL-A204CBFA R deodo.louver 1 1 1 AE
2-46 PFIL-A047CBEZ Deodorizer 2 2 2 AC
2-49 LSTPPA108CBFA Chilled stopper 2 2 2 AC
2-50 LSTPPA118CBFA Case stopper v 2 2 2 AC
2-55 HGRL-A209CBFA Multi louver s 1 1 1 AM
2-56 PFPFPB345CBFZ R-louver insu.s 1 1 1 AE
2-57 PSEL-C095CBEZ A-sealer r-louver 2 2 2 AB
2-63 LHLD-A484CBFA Fan motor holder b 1 1 1 AH
2-64 LHLD-A485CBFA Fan motor holder a 1 1 1 AH
2-65 PSEL-B209CBE0 U-sealer handle 2 2 2 AB
2-66 PSHEMA225CBPZ Heater cover 1 1 1 AC
2-67 LPLTMA633CBPZ Drain support al 1 1 1 AF
2-68 PSEL-A415CBE0 E.v cover sealer c 1 1 1 AC
2-69 PSEL-C069CBEZ E.v cover sealer d 1 1 1 AA
2-70 PSEL-C135CBEZ E.v cover sealer e 1 1 1 AC
2-71 PSEL-A552CBE0 Dial sealer 1 1 1 AC
2-72 PSEL-C078CBEZ A-sealer ag1 2 2 2 AC
2-73 PSEL-C079CBEZ A-sealer ag2 1 1 1 AB
2-77 LHLD-A391CBE0 Sl-5n clip 1 1 1 AD
2-78 LPLTMA399CBP0 Dryer support 1 1 1 AD
24
SJ-43L-A2
SJ-47L-A2
REF. NO. PART NO. DESCRIPTION Q'TY CODE
SJ-43L SJ-43L SJ-43L
-A2G -A2S -A2A
2-79 LBND-A019CBE0 Nylon band 1 1 1 AB
2-80 PBOX-A132CBFA Terminal box 1 1 1 AF
2-83 PSEL-C080CBEZ A-sealer ag3 1 1 1 AA
2-84 PSEL-C081CBEZ A-sealer ag4 2 2 2 AA
2-87 LBND-A018CBE0 Fastening band a 1 1 1 AP
2-91 HGRL-A202CBFA F return cover 1 1 1 AF
2-93 PCAP-A068CBFA C sliding cap a 4 4 4 AC
2-99 PSEL-A562CBE0 Leading wire sealer 1 1 1 AC
2-100 PSEL-C138CBEZ E.v cover sealer g 1 1 1 AA
2-101 PSEL-C139CBEZ Ev-insulation 47 2 2 2 AC
DOOR PARTS
3-5 FDORFB512CBKZ F-door s ass'y 1 - - BM
3-5 FDORFB513CBKZ F-door s ass'y - 1 - BL
3-5 FDORFB528CBKZ F-door s ass'y - - 1 BK
3-5-1 LSTPPA082CBFA Fd-stopper spring r 1 1 1 AD
3-5-2 NBRGPA013CBFB Nylon bearing 2 1 1 1 AH
3-5-3 LSTPMA008CBM0 F-door stopper r 1 1 1 AD
3-5-4 GDAI-A059CBMZ Badge base 1 1 1 AK
3-5-5 HBDGDA922CBEA Badge 1 - - AP
3-5-5 HBDGDA922CBEB Badge - - 1 AP
3-5-5 HBDGDA928CBEA Badge - 1 - AM
3-6 FPACGA346CBKZ F-door packing 1 1 1 AT
3-8 FHNDPA062CBKZ Door handle fl ass'y 1 - - AU
3-8 FHNDPA063CBKZ Door handle fl ass'y - 1 - AU
3-8 FHNDPA065CBKZ Door handle fl ass'y - - 1 AU
3-10 LPLTPA286CBFA Handle base fl 1 - - AK
3-10 LPLTPA286CBFB Handle base fl - 1 - AK
3-10 LPLTPA286CBFE Handle base fl - - 1 AK
3-15 FDORRB302CBKZ R-door ass'y 1 - - BR
3-15 FDORRB304CBKZ R-door ass'y - 1 - BR
3-15 FDORRB347CBKZ R-door ass'y - - 1 BQ
3-15-1 LSTPPA084CBFA Rd-stopper spring r 1 1 1 AD
3-15-2 NBRGPA022CBFA Nylon bearing 3s 1 1 1 AC
3-15-3 LSTP-A058CBM0 R-door stopper r 1 1 1 AF
3-17 FPACGA348CBKZ R-door packing 1 1 1 AV
3-19 FHNDPA070CBKZ Door handle rl ass'y 1 - - AU
3-19 FHNDPA071CBKZ Door handle rl ass'y - 1 - AU
3-19 FHNDPA073CBKZ Door handle rl ass'y - - 1 AU
3-21 LPLTPA287CBFA Handle base rl 1 - - AK
3-21 LPLTPA287CBFB Handle base rl - 1 - AK
3-21 LPLTPA287CBFE Handle base rl - - 1 AK
OTHER PARTS
4-1 LBND-A023CBE0 L-band c 2 2 2 AC
4-3 LX-VZA003CBE0 Special screw 2 2 2 AB
4-11 QTAN-A012CBE0 Solderless term. b 3 3 3 AH
4-15 LX-BZA018CBE0 Special screw 1 1 1 AA
4-17 LX-WZA003CBE0 Washer 4 4 4 AA
ATTACHMENT PARTS
5-1 UPOK-A180CBRA Bottle pocket 1 1 1 AR
5-2 UPOKPA268CBFA R door pocket s 2 2 2 AH
5-3 UPOK-A179CBRA Door pocket 3 3 3 AM
5-4 UPOK-A181CBRA R door pocket 1 1 1 AL
5-5 UTNA-A282CBFA Egg tray 1 1 1 AH
5-6 FSRA-A193CBYZ Ice cube maker 1 1 1 AS
5-9 USRA-A270CBFA Freezer tray 1 1 1 AT
5-13 HGRL-A201CBFA Ventilating grille 1 - - AM
5-13 HGRL-A201CBFB Ventilating grille - 1 - AM
5-13 HGRL-A201CBFE Ventilating grille - - 1 AM
5-14 USRA-A268CBFA Evaporating pan 1 1 1 AM
5-15 GGAD-A032CBFA V parting plate 1 1 1 AG
5-16 UYOK-A401CBFA Vegetable case 1 1 1 AX
5-17 UYOK-A399CBFA Ice storage box 1 1 1 AL
5-18 UYOK-A400CBFA Fresh case 1 1 1 AV
5-19 GDORPA072CBRA Fresh door hs 1 1 1 AN
5-24 USRA-A272CBFA Refrigerator tray 2 2 2 AU
5-25 USRA-A271CBFA Vegetable tray 1 1 1 AW
5-31 LRALPA136CBFA Ice tray holder l 1 1 1 AG
5-32 LRALPA137CBFA Ice tray holder r 1 1 1 AG
5-35 UPOKPA269CBFA Bottle stopper 1 1 1 AC
25
SJ-43L-A2
SJ-47L-A2
REF. NO. PART NO. DESCRIPTION Q'TY CODE
SJ-43L SJ-43L SJ-43L
-A2G -A2S -A2A
1. MODEL NUMBER 2. REF. NO.
3. PART NO. 4. DESCRIPTION
HOW TO ORDER REPLACEMENT PARTS
To have your order filled promptly and correctly, please furnish the following information.
CYCLE PARTS
6-1 PCMPLA215CBEZ Compressor 1 1 1 BW
6-2 PSPAGA042CBE0 Rubber grommet 4 4 4 AE
6-4 FFRM-A120CBKZ Base frame ass'y 1 1 1 AG
6-5 FDRY-A006CBK0 Dryer ass'y 1 1 1 AX
6-6 PCLI-A050CBE0 Clip 1 1 1 AD
6-9 PSPAFA034CBE0 Sleeve 4 4 4 AD
6-11 PPIPCA386CBEZ S.p connector 1 1 1 AF
6-18 PPIPCA252CBE0 Charge pipe 2 2 2 AD
6-19 FPIPCA172CBKZ Discharge p. ass'y 1 1 1 AM
6-21 PCOVPA246CBE0 Terminal cover 1 1 1 AL
6-24 PGUM-A004CBF0 Absorbent rubber a 2 2 2 AH
6-25 QTAN-A045CBE0 Terminal block 1 1 1 AQ
6-26 FPIPCA162CBKZ Eva pan pipe s ass'y 1 1 1 AS
6-28 LANG-A058CBPZ Absorbent rubber clm 2 2 2 AC
6-29 PGUM-A003CBF0 Absorbent rubber b 2 2 2 AH
MISCELLANEOUS
90-1 TINS-A542CBRZ Operation manual 1 1 1 AE
90-2 TLAB-A876CBRZ Warning label 1 1 1 AC
90-3 SPAKCJ150YDEZ Packing case 43l-3 1 1 1 AZ
90-5 TLAB-A897CBEZ Case label a2g 4 - - AC
90-5 TLAB-A937CBEZ Case label a2a - - 4 AB
90-5 TLAB-A973CBEZ Case label a2s - 4 - AC
90-6 CPADBA799YDKZ Bottom pad ass'y 1 1 1 AV
90-7 CPADBA798YDKZ Top pad ass'y 1 1 1 AQ
90-8 SPADBC439YDEZ Corner post fl 1 1 1 AK
90-9 SPADBC440YDEZ Corner post fr 1 1 1 AK
90-10 SPADBC435YDEZ Corner post bl 1 1 1 AG
90-11 SPADBC436YDEZ Corner post br 1 1 1 AG
90-12 TLAB-B032CBRZ Energy label 1 1 1 AE
90-16 TLAB-A985CBRZ Two star label 1 1 1 AF
90-21 TLAB-A939CBRZ Caution label rof 1 1 1 AD
26
SJ-43L-A2
SJ-47L-A2
REF. NO. PART NO. DESCRIPTION Q'TY CODE
REPLACEMENT PARTS LIST(SJ-47L-A2G/A2S/A2A)
SJ-47L SJ-47L SJ-47L
-A2G -A2S -A2A
ELECTRIC PARTS
1-1 RTHM-A103CBZZ F-themostat 1 1 1 AV
1-2 RSTT-A134CBE0 Starting relay 1 1 1 AS
1-3 QSWTDA047CBZZ Defrost timer 1 1 1 AZ
1-4 PDMP-A050CBEZ Damper thermo 1 1 1 AW
1-5 FTHM-A039CBKZ Defrost thermo.ass'y 1 1 1 AM
1-6 RMOTRA046CBE0 Fan motor 1 1 1 AZ
1-7 QSOCAA084CBEZ Lamp socket 1 1 1 AL
1-8 RLMP-A029CBEZ Lamp15w 1 1 1 AH
1-9 QACC-A142CBZZ Source cord 1 1 1 AQ
1-10 QSW-PA090CBZA Door switch 1 1 1 AS
1-11 RHOG-A161CBZZ Protector 1 1 1 AX
1-17 FFS-TA061CBKZ Fuse ass'y 1 1 1 AM
1-20 FW-VZA146CBEZ Lead ev-cover ass'y 1 1 1 AL
1-21 FHETBA161CBEZ Def.heater ass'y 1 1 1 AY
1-22 FCNW-A688CBKZ Relay cord s ass'y 1 1 1 AR
1-23 QCNW-A969CBZZ Reray wire rc 1 1 1 AD
1-32 RC-EZA195CBZZ Running capacitor 1 1 1 BB
1-33 QCNW-A886CBE0 Olr cord 1 1 1 AE
MECHANICAL PARTS
2-2 JKNB-A036CBFC F-temp. control knob 1 1 1 AC
2-4 LHLD-A489CBFA E.v. holder 2 2 2 AD
2-7 FLEGPA083CBKZ Leg holder l ass'y 1 1 1 AF
2-7-1 FAJS-A015CBKZ Adjustable leg ass'y 2 2 2 AE
2-7-2 LHLD-A533CBPZ Leg holder l 1 1 1 AL
2-8 FLEGPA084CBKZ Leg holder r ass'y 1 1 1 AF
2-8-2 LHLD-A534CBPZ Leg holder r 1 1 1 AP
2-13 DHNG-A417CBMZ Upper hinge ass'y 1 1 1 AE
2-14 DHNG-A419CBMZ Bottom hinge r ass'y 1 1 1 AD
2-15 DHNG-A418CBMZ Center hinge r ass'y 1 1 1 AE
2-16 GCOV-A210CBFZ E.v cover 1 1 1 AR
2-17 LCRA-A010CBE0 Fan clamp 1 1 1 AD
2-19 LHLD-A389CBF0 Motor cushion 2 2 2 AF
2-20 NFANPA011CBF0 Propeller fan 100 1 1 1 AD
2-21 PSEL-C067CBEZ E.v cover sealer a 1 1 1 AA
2-22 PSEL-C068CBEZ E.v cover sealer b 1 1 1 AA
2-23 PSEL-C066CBEZ E.v cover sealer c 1 1 1 AC
2-24 PCOVPA308CBFA Terminal cover 1 1 1 AE
2-26 PCOV-A277CBFA R lamp cover 1 1 1 AE
2-27 GCOVPA142CBRA R-c box cover 1 1 1 AQ
2-28 HGRL-A206CBRA Fan louver 1 1 1 AS
2-29 GCOV-A209CBFA Upper hinge cover 1 - - AC
2-29 GCOV-A209CBFB Upper hinge cover - 1 - AC
2-29 GCOV-A209CBFE Upper hinge cover - - 1 AD
2-31 JKNB-A033CBFC R-temp.control knob 1 1 1 AC
2-32 JKNB-A063CBFA V-tray control knob 1 1 1 AC
2-36 PCAP-A006CBFX Screw cover 2 - - AB
2-36 PCAP-A006CBFY Screw cover - - 2 AB
2-36 PCAP-A077CBFA Screw cover - 2 - AA
2-38 PGID-A161CBFZ R-air guider 1 1 1 AG
2-39 PGID-A162CBFZ R-air guider s 1 1 1 AC
2-41 PSEL-B848CBEZ A-sealer thermo.cap 1 1 1 AC
2-44 HGRL-A203CBRA F deodo.louver 1 1 1 AF
2-45 HGRL-A204CBFA R deodo.louver 1 1 1 AE
2-46 PFIL-A047CBEZ Deodorizer 2 2 2 AC
2-49 LSTPPA108CBFA Chilled stopper 2 2 2 AC
2-50 LSTPPA118CBFA Case stopper v 2 2 2 AC
2-55 HGRL-A205CBFA Multi louver l 1 1 1 AM
2-56 PFPFPB334CBFZ R-louver insu.l 1 1 1 AE
2-57 PSEL-C085CBEZ A-sealer r-louver 2 2 2 AC
2-63 LHLD-A484CBFA Fan motor holder b 1 1 1 AH
2-64 LHLD-A485CBFA Fan motor holder a 1 1 1 AH
2-65 PSEL-B209CBE0 U-sealer handle 2 2 2 AB
2-66 PSHEMA225CBPZ Heater cover 1 1 1 AC
2-67 LPLTMA633CBPZ Drain support al 1 1 1 AF
2-68 PSEL-A415CBE0 E.v cover sealer c 1 1 1 AC
2-69 PSEL-C069CBEZ E.v cover sealer d 1 1 1 AA
2-70 PSEL-C135CBEZ E.v cover sealer e 1 1 1 AC
2-71 PSEL-A552CBE0 Dial sealer 1 1 1 AC
2-72 PSEL-C078CBEZ A-sealer ag1 2 2 2 AC
2-73 PSEL-C079CBEZ A-sealer ag2 1 1 1 AB
2-77 LHLD-A391CBE0 Sl-5n clip 1 1 1 AD
2-78 LPLTMA399CBP0 Dryer support 1 1 1 AD
27
SJ-43L-A2
SJ-47L-A2
REF. NO. PART NO. DESCRIPTION Q'TY CODE
SJ-47L SJ-47L SJ-47L
-A2G -A2S -A2A
2-79 LBND-A019CBE0 Nylon band 1 1 1 AB
2-80 PBOX-A132CBFA Terminal box 1 1 1 AF
2-83 PSEL-C080CBEZ A-sealer ag3 1 1 1 AA
2-84 PSEL-C081CBEZ A-sealer ag4 2 2 2 AA
2-87 LBND-A018CBE0 Fastening band a 1 1 1 AP
2-91 HGRL-A202CBFA F return cover 1 1 1 AF
2-93 PCAP-A068CBFA C sliding cap a 4 4 4 AC
2-99 PSEL-A562CBE0 Leading wire sealer 1 1 1 AC
2-100 PSEL-C138CBEZ E.v cover sealer g 1 1 1 AA
2-101 PSEL-C139CBEZ Ev-insulation 47 2 2 2 AC
DOOR PARTS
3-5 FDORFB512CBKZ F-door s ass'y 1 - - BM
3-5 FDORFB513CBKZ F-door s ass'y - 1 - BL
3-5 FDORFB528CBKZ F-door s ass'y - - 1 BK
3-5-1 LSTPPA082CBFA Fd-stopper spring r 1 1 1 AD
3-5-2 NBRGPA013CBFB Nylon bearing 2 1 1 1 AH
3-5-3 LSTPMA008CBM0 F-door stopper r 1 1 1 AD
3-5-4 GDAI-A059CBMZ Badge base 1 1 1 AK
3-5-5 HBDGDA922CBEA Badge 1 - - AP
3-5-5 HBDGDA922CBEB Badge - - 1 AP
3-5-5 HBDGDA928CBEA Badge - 1 - AM
3-6 FPACGA346CBKZ F-door packing 1 1 1 AT
3-8 FHNDPA062CBKZ Door handle fl ass'y 1 - - AU
3-8 FHNDPA063CBKZ Door handle fl ass'y - 1 - AU
3-8 FHNDPA065CBKZ Door handle fl ass'y - - 1 AU
3-10 LPLTPA286CBFA Handle base fl 1 - - AK
3-10 LPLTPA286CBFB Handle base fl - 1 - AK
3-10 LPLTPA286CBFE Handle base fl - - 1 AK
3-15 FDORRB300CBKZ R-door ass'y 1 - - BS
3-15 FDORRB303CBKZ R-door ass'y - 1 - BR
3-15 FDORRB343CBKZ R-door ass'y - - 1 BR
3-15-1 LSTPPA084CBFA Rd-stopper spring r 1 1 1 AD
3-15-2 NBRGPA022CBFA Nylon bearing 3s 1 1 1 AC
3-15-3 LSTP-A058CBM0 R-door stopper r 1 1 1 AF
3-17 FPACGA347CBKZ R-door packing 1 1 1 AV
3-19 FHNDPA070CBKZ Door handle rl ass'y 1 - - AU
3-19 FHNDPA071CBKZ Door handle rl ass'y - 1 - AU
3-19 FHNDPA073CBKZ Door handle rl ass'y - - 1 AU
3-21 LPLTPA287CBFA Handle base rl 1 - - AK
3-21 LPLTPA287CBFB Handle base rl - 1 - AK
3-21 LPLTPA287CBFE Handle base rl - - 1 AK
OTHER PARTS
4-1 LBND-A023CBE0 L-band c 2 2 2 AC
4-3 LX-VZA003CBE0 Special screw 2 2 2 AB
4-11 QTAN-A012CBE0 Solderless term. b 3 3 3 AH
4-15 LX-BZA018CBE0 Special screw 1 1 1 AA
4-17 LX-WZA003CBE0 Washer 4 4 4 AA
ATTACHMENT PARTS
5-1 UPOK-A180CBRA Bottle pocket 1 1 1 AR
5-2 UPOKPA268CBFA R door pocket s 2 2 2 AH
5-3 UPOK-A179CBRA Door pocket 3 3 3 AM
5-4 UPOK-A181CBRA R door pocket 1 1 1 AL
5-5 UTNA-A282CBFA Egg tray 1 1 1 AH
5-6 FSRA-A193CBYZ Ice cube maker 1 1 1 AS
5-9 USRA-A270CBFA Freezer tray 1 1 1 AT
5-13 HGRL-A201CBFA Ventilating grille 1 - - AM
5-13 HGRL-A201CBFB Ventilating grille - 1 - AM
5-13 HGRL-A201CBFE Ventilating grille - - 1 AM
5-14 USRA-A268CBFA Evaporating pan 1 1 1 AM
5-15 GGAD-A032CBFA V parting plate 1 1 1 AG
5-16 UYOK-A401CBFA Vegetable case 1 1 1 AX
5-17 UYOK-A399CBFA Ice storage box 1 1 1 AL
5-18 UYOK-A400CBFA Fresh case 1 1 1 AV
5-19 GDORPA072CBRA Fresh door hs 1 1 1 AN
5-24 USRA-A272CBFA Refrigerator tray 2 2 2 AU
5-25 USRA-A271CBFA Vegetable tray 1 1 1 AW
5-31 LRALPA136CBFA Ice tray holder l 1 1 1 AG
5-32 LRALPA137CBFA Ice tray holder r 1 1 1 AG
5-35 UPOKPA269CBFA Bottle stopper 1 1 1 AC
28
SJ-43L-A2
SJ-47L-A2
REF. NO. PART NO. DESCRIPTION Q'TY CODE
SJ-47L SJ-47L SJ-47L
-A2G -A2S -A2A
HOW TO ORDER REPLACEMENT PARTS
To have your order filled promptly and correctly, please furnish the following information.
1. MODEL NUMBER 2. REF. NO.
3. PART NO. 4. DESCRIPTION
CYCLE PARTS
6-1 PCMPLA215CBEZ Compressor 1 1 1 BW
6-2 PSPAGA042CBE0 Rubber grommet 4 4 4 AE
6-4 FFRM-A120CBKZ Base frame ass'y 1 1 1 AG
6-5 FDRY-A006CBK0 Dryer ass'y 1 1 1 AX
6-6 PCLI-A050CBE0 Clip 1 1 1 AD
6-9 PSPAFA034CBE0 Sleeve 4 4 4 AD
6-11 PPIPCA386CBEZ S.p connector 1 1 1 AF
6-18 PPIPCA252CBE0 Charge pipe 2 2 2 AD
6-19 FPIPCA172CBKZ Discharge p. ass'y 1 1 1 AM
6-21 PCOVPA246CBE0 Terminal cover 1 1 1 AL
6-24 PGUM-A004CBF0 Absorbent rubber a 2 2 2 AH
6-25 QTAN-A045CBE0 Terminal block 1 1 1 AQ
6-26 FPIPCA162CBKZ Eva pan pipe s ass'y 1 1 1 AS
6-28 LANG-A058CBPZ Absorbent rubber clm 2 2 2 AC
6-29 PGUM-A003CBF0 Absorbent rubber b 2 2 2 AH
MISCELLANEOUS
90-1 TINS-A542CBRZ Operation manual 1 1 1 AE
90-2 TLAB-A876CBRZ Warning label 1 1 1 AC
90-3 SPAKCJ148YDEZ Packing case 47l-3 1 1 1 BA
90-5 TLAB-A897CBEZ Case label a2g 4 - - AC
90-5 TLAB-A937CBEZ Case label a2a - - 4 AB
90-5 TLAB-A973CBEZ Case label a2s - 4 - AC
90-6 CPADBA799YDKZ Bottom pad ass'y 1 1 1 AV
90-7 CPADBA798YDKZ Top pad ass'y 1 1 1 AQ
90-8 SPADBC439YDEZ Corner post fl 1 1 1 AK
90-9 SPADBC440YDEZ Corner post fr 1 1 1 AK
90-10 SPADBC435YDEZ Corner post bl 1 1 1 AG
90-11 SPADBC436YDEZ Corner post br 1 1 1 AG
90-12 TLAB-B029CBRZ Energy label 1 1 1 AE
90-15 TLAB-B055CBEZ R-door pocket label 1 1 1 AC
90-16 TLAB-A985CBRZ Two star label 1 1 1 AF
90-21 TLAB-A939CBRZ Caution label rof 1 1 1 AD
29
SJ-43L-A2
SJ-47L-A2
A
B
C
D
E
F
G
H
A
123456
123456
B
C
D
E
F
G
H
DOOR PARTS
SJ-43L-A2
SJ-47L-A2
3-6
3-5
3-8
3-10
3-5-2
5-3
5-4
5-5
5-1
5-3
3-5-3
3-5-1
3-15-2
3-15-1
3-17
5-35
3-15
5-2
3-5-4
5-2
90-15
3-5-5
3-15-3
3-19
3-21
30
SJ-43L-A2
SJ-47L-A2
A
B
C
D
E
F
G
H
A
123456
123456
B
C
D
E
F
G
H
CABINET PARTS
SJ-43L-A2
SJ-47L-A2
2-29
2-13
2-49
2-49
2-91
2-7
2-7-2
2-7-1
2-8
2-8-2
2-7-1
2-14
5-31
5-17
5-6
5-32
5-9
5-24
1-10
2-15
5-13
4-3
5-25
2-32
5-16
2-93
2-93
2-93
2-93
5-18
5-19
2-36
2-36
5-15
31
SJ-43L-A2
SJ-47L-A2
A
B
C
D
E
F
G
H
A
123456
123456
B
C
D
E
F
G
H
SJ-43L-A2
SJ-47L-A2
CABINET PARTS
6-11
6-28
6-1
2-87
2-31
6-9
6-2
4-17
1-2
6-4
1-9
2-80
2-24
6-18
6-5
6-18
4-11
2-78
2-66
2-67
1-21
1-22
6-21
4-15
2-2
6-26
2-72
1-4
2-41
2-83
2-73
2-71
2-38
2-39
2-79
1-3
2-27
2-46
2-84
2-45
1-7
2-50
1-8
90-2
2-57
2-56
2-55
2-26
2-63
2-19
1-6
2-19
2-64
2-20
2-17
2-21
2-22
2-68
1-17
4-1
1-5
1-1
1-20
2-65
4-1
2-23
2-16
2-28
6-19
6-6
6-25
2-46
2-84
2-44
5-14
6-29
2-70
2-69
2-99
6-24
2-4
2-100
2-101
1-33
1-11
1-32
1-23
2-77
32
SJ-43L-A2
SJ-47L-A2
COPYRIGHT © 2002 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced, stored in retrieval systems, or
transmitted in any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise, without prior written
permission of the publisher.
2002 SHARP CORP. (06S0.01E) Printed in Japan
43JPS3/ 43JPU3/ 43JPQ3T/ 47JPS3/ 47JPU3/ 47JPQ3
Loading...