@ For the options, refer to their service manuals.
CONTENTS
•This model is a minor change model based on the SF-2020/2120. This Service
Manual described only the changed items from the base model. For the items
common with the SF-2020.2120, refer to the Service Manual of the SF-2020/2120.
•The SF-2220 /2320 circuit diagrams are same as those of the SF-2020/2120.
Therefore, please refer to the SF2020/2120 circuit diagrams.
Parts marked with "!" is important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
This document has been published to be used
SHARP CORPORATION
for after sales service only.
The contents are subject to change without notice.
[1] PRODUCT OUTLINE
1. Different points between SF-2220/2320 and SF-2020/2120
Model name
Item
Multi paper feed unit
Personal counter
(SF-71A/B)
Paper size detectionAvailableBlack
Original cover
Maintenance parts lifeUnit: 50K Unit: 60K
SF-2020SF-2120SF-2220SF-2320Remark
Standard
provision
Options
(Service item)
Standard
provision
Option
(SF-MF15)
Service item
2. System configuration (options)
To install the Personal Counter, a Counter
fixing plate (LPLTM4963FCZZ), four Screw
(XHPSD40P06000 × 2, XBSSD30P06000 × 2)
and a Edge plate (LBSHL0323FCZZ) are
required.
The paper size of each tray is set with the
user program. (Refer to the paper size setting
mode.)
Option
(SF-CV13)
10-bin sorter SF-S17N
Two-step paper feed unit SF-CM15
10-bin staple sorter SF-S54
Multi paper feed unit SF-MF15
Original cover SF-CV13 (SF-2320 only)
Reversing automatic document feeder SF-A57
(SF-2320 only)
Automatic document feeder SF-A18
One-step paper feed unit SF-CM16
Tray (reserve) SF-UB15
1 – 1
[2] PRODUCT SPECIFICATIONS
1. Basic specifications
(1) Type: Table top
(2) Copy speed:
<SF-2220/2320>
IPaper trayJDeveloping unit gripKDeveloping unit strap
LToner hopperMDeveloping unit lock leverNRelease lever
OFusing unitPDrum
3 – 1
2. Operation panel
SF-2220
(AB series)
(AB series)
SORTER
SORT
STAPLE
SORT
GRO UP
1615
1615
3 4
ORIGINAL
EXPOSURE
12345
LIGH T
DARK
18
17
2019
1
...
...
...
...
...
12345
1817
2019
PAPER
SIZE
SIZE
A3
A4
A4
A5
B4
EXTRA
21
3
A3
A4
A4
A5
B4
EXTRA
21
5 2 1
TRAY SEL EC TAUT O I MA G E
22
4 5 2
AUTO %
22
PRESET
RATIO
100%
100%
6
252423
6
252423
8 7 9 1011
200%
141%
122%
115%
86%
81%
70%
%
50%
27
26
7 9 1011
200%
141%
122%
115%
86%
81%
70%
50%
26
27
29
28
8
%
29
28
1
4
7
0/
30
1
45
7
0/
30
12
23
6
5
8
9
C
3132
12
23
6
8
9
C
3132
POWER SAVE
1314
AUDIT CLEAR
CA
1314
ACC.#-C
CA
No.NameNo.NameNo.Name
1 1-set 2-copy key/Display lamp2 Density selection key/Display lamp3 Paper jam lamp
4 Paper supply lamp5 Tray position/Paper jam position lamp6 Magnification ration lamp
7 Maintenance lamp8 Copy quantity display9 Mini maintenance lamp
F Toner supply lampG 10-key padH Pre-heat lamp
I Department count end keyJ All clear keyK Clip tray
L Sorter key/Display lampMBinding margin key/display lampN Edge erase key/Edge erase lamp
O Density adjustment key/Display lampP Original size display lampQ Paper size display lamp
R Tray selection keyS Paper auto selection display lampT Auto magnification ratio selection
key/Display lamp
U Magnification ratio selection keyV Zoom lampW % key
X Zoom keyY Interruption key/Display lampZ Zero-Read-out key
[ Erase key\ PRINT button
3 – 2
SF-2320
(AB series)
(AB series)
SORTER
SORT
STAPLE
SORT
GROUP
1615
1615
ORIG INAL
TO COPY
33
2 1
ORIG INAL
EXPOSURE
SIZE
AUTO
MANUAL
PHOTO
12345
LIGH TDARK
1817
2019
A3
A4
A4
A5
B4
EXTRA
PAPER
SIZE
3 4
3 4
...
...
...
...
...
...
...
...
?
33
AUTO
12345
1817
A3
A4
A4
A5
B4
EXTRA
2019
5
TRAY SELECTAUTO IMAGE
2423
2221
5 2 1
AUTO %
2221
PRESET
RATIO
100%
100%
6
25
6
252423
8 7 9 1011
200%
141%
122%
115%
86%
81%
70%
50%
26
200%
141%
122%
115%
86%
81%
70%
50%
26
INTER RUPT
ZOOM
%
27
28
8
7 9 1011
ZOOM
%
27
28
1
2
4
5
8
7
0/
C
29
303132
1
2
5
4
89
7
0/
C
29
30
3132
3
6
9
3
6
12
POWER SAVEAUDIT CLEAR
12
ACC.#-C
13
CA
1314
CA
14
No.NameNo.NameNo.Name
1 1-set 2-copy key/Display lamp2 Density selection key/Display lamp3 Paper jam lamp
4 Paper supply lamp5 Tray position/Paper jam position lamp6 Magnification ration lamp
7 Maintenance lamp8 Copy quantity display9 Mini maintenance lamp
F Toner supply lampG 10-key padH Pre-heat lamp
I Department count end keyJ All clear keyK Clip tray
L Sorter key/Display lampMBinding margin key/display lampN Edge erase key/Edge erase lamp
O Density adjustment key/Display lampP Original size display lampQ Paper size display lamp
R Tray selection keyS Paper auto selection display lampT Auto magnification ratio selection
key/Display lamp
U Magnification ratio selection keyV Zoom lampW % key
X Zoom keyY Interruption key/Display lampZ Zero-Read-out key
[ Erase key\ PRINT button] Duplex key/Display lamp (SF-2320 only)
3 – 3
[4] UNP ACKING AND INSTALLATION
14. Optional multi paper feed unit
(SF-MF15) installation
Disconnect the power plug of the copier and
perform the following procedures.
1 Open the front cabinet of the copier and lift the upper unit slowly
with the open/close lever.
Body open/close lever
Upper unit
3 Insert the positioning pins of the multi paper feed unit into the
installation holes of the copier.
At that time, first insert the rear pins, then insert the front pins.
(Check that the multi paper feed unit connecting pins are properly
connected.)
Then fix the multi paper feed unit with the two screws which were
removed in procedure (2).
Rear side
Positioning pin
Installation holes
Fixing screw
Fixing screw
Multi paper feed unit
Positioning pin
Front cabinet
2 Remove two fixing screws of the right cabinet, and remove the
right cabinet. The two removed screws are used for installation of
the multi paper feed unit to the copier.
Right cabinet lower
Front side
4 With the above procedure, the multi paper feed unit installation is
completed.
* Close th e up per uni t slo wly an d close the f ront cab inet. The mul ti
paper feed unit mode is automatically set.
15. Personal counter (Service item)
1 Remove the upper cabinet left and the left cabinet.
1)
2)
Fixing screw
* Keep the right cabinet, which is required when the multi paper feed
unit is removed.
4)
3)
3)
4 – 12
2 Attach the mechanical counter attachment plate
(LPLTM4963FCZZ) to the optical system base plate.
At that time, be careful to avoid contact between the mechanicalcounter attachment plate and the main harness.
3 Attach the counter socket (SF71B) to the mechanical counterat-
tachment plate.
5 Cut off the notch section of the left cabinet, and attach theupper
cabinet left and the left cabinet to the copier.
5)
4)
2)
2)
4 Fix the counter socket with a screw and connect the countersock-
et harness and he copier harness.
(Disconnect the 1P harness connector of the copier, and connectwith the counter socket harness.)
5)
3)
1)
4)
2)
3)
3)
1)
1)
2)
4 – 13
[5] DESCRIPTIONS OF EACH
SECTION
Descri ptions are made on the follow ing sections:
1 Paper feed section
2 Developing section
3 Optical section
4 Process section
5 Separation/transport section
6 Fusing/paper exit section
7 High voltage section
8 ADU section (SF-2120 only)
In the c ase of SF- 2220:
The SF- 2220 is p rovided with th e three -way pa per fee d system . The
tray is of the u niv er s al type and has capacity of 2 50 sh eets. Th e fr on t
loading system allows the tray to be loaded from the lower side of the
front cabinet.
(The SF-2320 has the two-way paper feed system with one 250sheet tr ay and manual feed.)
The tray has the capacity of 500 sheets (250 sheets for the SF-2 320).
In addi tion to that, th e option al paper feed uni t allows loading o f 500
sheets more for the SF-CM15 (250 sheets for the SF-CM16).
2) Basic operati ons
(Tray paper feed operat ion)
When the CPFC (Cassette paper feed clutch) turn on, the paper feed
roller shaft, t he paper fe ed roller, and the ta ke-up roller rotat e in the
direction of A. At the same time, the limiter spring moves down the
roller release arm. As a result, the take-up roller falls by its own
weight onto the paper surf ace, start ing paper feed.
Roll er r elease arm
Take-up
roller
SF-MF15
(Option)
SF-CM15
(Option)
1. Paper feed secti on
1) General descriptions
To real ize the com pact desig n, the fro nt loading s ystem and th e foldable m ulti pap er feed unit are employed.
Use of th e op tio nal t wo- stag e pa pe r fe ed u nit f or t he SF -CM1 5 ( onestage p aper feed unit for the S F-CM16) an d the spa re tray allow s a
variety of system configurations.
(System configuration) Example with the SF-2220:
SF-2220
250 sheets
50 sheets
(One-step paper feed unit)
(Two-step paper feed unit)
Multi paper feed unit
SF-MF15 (Option)
250 sheets
SF-CM16
Or
250 sheets
250 sheets
SF-CM15
250 sheets
SF-UB15
(Spare tray)
Paper f eed ro l l er
Paper feed roller shaft
When the CPFC turns off, rotation stops and the take-up roller is
pushed up to the original position by the roller release arm sprin g.
(Multi manual paper feed operation)
When the MPFS (multi paper feed solenoid) turns on, the spring
clutch rotates to pr ess the take- up roller on t he paper, feeding the
paper.
5 – 1
[6] DISASSEMBLY AND ASSEMBLY
The descriptions are divided into the following sections.
1. Paper feed section
2. Transport section and power section
3. Fusing section
4. Optical system
5. SPF section
6. Drum section
7. Developing section
8. Operation panel section and intermediate cabinet
9. Major parts on the frame side
10. Manual multi paper feed unit (SF-MF15, option)
11. Paper feed unit (SF-CM15, SF-CM16, option)
1. Paper feed section
1-1. Paper feed unit
1 Open the front cover and lift up the upper clamshell. Remove two
fixing screws of the manual paper feed section, and remove the
manual paper feed section.
(Note for assem bly)
1) There is the 8-pin connector on the back of the rear frame side.
When assembling it, carefully insert.
2) The belt must be on the paper feed unit gear and the resist roller
gear.
1-2. Paper feed roller ass’y removal
1) Remove the rear frame side electromagnetic clutch connector.
2) Remove the front frame side stopper and the bearing.
3) Remove the roller release arm spring from the paper feed frame.
2 Remove the four fixing screws (M4 x 10 x 1pcs, step screw x 1 pc)
of the paper feed unit, and lift the rear frame side of the paper
feed unit and remove it. (Since there is the 8-pin connector on the
back of the rear frame side, it requires some force to remove.
Carefully pull it out straight.)
4) Remove the rear frame bearing, and one side of the paper feed
roller ass’y will be disengaged. To remove the ass’y completely,
remove the E-ring.
(Note for assem bly 1)
With r oller rel ease arm s pring A hooke d on th e spring notch, att ach
the pa per feed r ol ler a ss ’y to the pa per feed u nit, and ho ok the spr ing
on the paper feed frame.
A
A
6 – 1
[8] SIMULATION
6. User simulation
This simulation allows to change and set the following setting which has been set when shipping from the factory.
(1) Functions which can be set and canceled by the user simulation
Function nameFunction and setting contentFactory setting
• After completion of copying, when a certain time is passed, the machine returns to the initial
Auto clear
Pre-heat
Auto power shut off
Auto pre-heat control
Auto shut OFF
Auto document
feeding unit manual
document feed mode
Sorter take-out mode
* Note: The value of power consumption in pre-heat or in auto power shut off may vary according to the use conditions.
state automatically. The time to return to the initial state is set in the range of 30 - 120 sec in
increment of 30 sec. This function can be cleared.
• When the copier is left without copying with the power ON, the power consumption is
automatically lowered to 60Wh. The time to start this function is set in the range of 1 min - 120
min.
• When this function operates, the pre-heat lamp on the operation panel is lighted.
To return to the initial state:
Press any key on the operation panel. (If the COPY button is pressed, the machine returns to
the initial state and performs copying.)
If also the original is set or the tray is pulled out, the machine returns to the initial state.
• When the copier is left without copying with the power ON, the power consumption is
automatically lowered to 10Wh. The time to start this function is set in the range of 5 min - 120
min.
• When this function operates, al the lamps on the operation panel except for the pre-heat lamp
are turned off.
To return to the initial state:
Press the COPY button. The machine returns to the initial state.
• This function learns the use conditions of the copier to automatically control the time to start the
pre-heat function and the auto power shut off function to the optimum level. This function can
be activated or inactivated.Cancel
• When this function is activated, the time settings in the pre-heat function and the auto power
shut off function are ignored.
• When the copier is left without copying for a certain period, this function is used to enable or
disable the function of lowering the power consumption.
• By use of the auto document feeder (option), originals of different sizes are fed manually.
• When this function is activated, set an original during the original feed lamp blinks after
completion of copying of the previous original, and the original is fed automatically.
• When the sorter (option) is installed, the interval between bins can be extended to facilitate to
take out the copy by pressing the copy take-out key.
60 sec
15 min
30 min
Set
Cancel
Set
(2) User simulation
Simulation procedureState
1. Pres s the tray selecti on
key for 5 sec or more.
2. Enter the simulation code
No. with the10-key pad.
3. Press the COPY button.Determination of simulation code
4. Enter the selection code
No. with the 10-key pad.
5. Press the COPY button.Determination of simulation code menu
6. Pres s the tray selecti on
key.
* Press the clear key.(Use this key in case of erroneous input)
User simulation input is allowed.
Selection of simulation code No.
Selection of simulation code menu
Escape from user simulation.
• When this key is pressed during selection of user
simulation, the mode returns to 1 (User simulation is
allowed.).
• After setting the program, when this key is pressed, the
next program input is allowed.
(: Blink)
8 – 16
Warning
LED
BlinkBlinkOFF
BlinkBlinkON
BlinkOFF
BlinkOFF
BlinkOFF
OFFOFF
BlinkBlinkOFF
Paper
supply LED
Copy
quantity
display
1
Returns to
the copy
quantity
display.
Copy
button
LED
11
21
21
ON
ON
OFF
—
(3) Paper size setting mode
ProcedureState
1Press the tray select key for 5 sec.Same as setting of the user simulation.
Select the tray to be set with the zoom key.The display of "– –" on the number display disappears and the
2
Select the fixed magnification ration for the set tray paper size.The paper size is changed in sequence every time when the
3
4Press the COPY button to determine the paper size—
Press the tray selection key.Escape from paper size setting mode
5
Press the clear key• After setting the paper size, when this key is pressed, the mode
*
display lamp of set tray is lighted.
magnification ratio key is pressed.
• When this key is pressed during selection of paper size setting
mode, the mode returns to 1 (Paper size setting mode is
allowed.).
returns to 2 (Paper size setting mode is allowed.).
(4) User simulation co de tab le
ProgramSim. codeSelection code: Set contentFactory setting
Auto clear passing time setting
[1]
Pre-heat mode setting and passing time setting
[2]
Auto power shut off mode setting and passing time setting
[3]
Auto pre-heat control mode setting and cancel *
Auto document feeder manual document feed mode setting
Sorter take-out mode
Auto paper selection
Auto tray selection
Auto power shut OFF setting
* When the auto pr e-heat control f unction is selected, the setting of pre-heat/auto pow er shut off becom es invali d.
[0]: Cancel
[1]: 1 min
[2]: 15 min
[3]: 60 min
[4]: 120 min
[1]: 5min
[2]: 15 min
[3]: 30 min
[4]: 60 min
[5]: 120 min
[6]: 240 min
[0]: Cancel
[1]: Setting
[0]: Cancel
[1]: Setting
[0]: Cancel
[1]: Setting
[0]: Cancel
[1]: Setting
[0]: Cancel
[1]: Setting
[0]: Cancel
[1]: Setting
2
2
3
0
0
1
1
1
1
8 – 17
(5) Department counter setting content (Set with user program P10 ∼ P15)
• Simple department counter
Number of departments: 20 Dept.
Dept. No.:3 digits (000 is excluded.)
Count range:0 to 49,999 sheets (When reaching 50,000, it starts from 0 again.)
Mode display:[——] blinking on the entered number display.
✕ = Check (Clean, replace, or adjust if necessary.)
* The toner consumption and the waste toner bottle replacement cycle are those when the reference chart is used.
SectionParts60K120K180K240K300KRemark
Developerbbbbb
DV bladeFbFbF
DV side seal (F/R)FbFbF
Drumbbbbb
Cleaner bladebbbbb
Toner reception sealbbbbb
Drum separation pawlbbbbb
Charging plate (saw teeth)FbFbF
MC caseFFFFF
Screen gridFbFbF
Discharge lampFFFFF
Blank lampFFFFF
Drum mark sensorFFFFF
Drum density sensorFFFFF
Waste toner bottleFFFFF
TC/SC caseFFFFF
TC/SC wireFbFbF