SHARP Service manual / Схема, сервісна інструкція Service manual & schematics

Page 1

SHARP SERVICE MANUAL

S35M113G-M60/

COLOR TELEVISION

Chassis No. SN-50

13G-M60

In the interests of user-safety (Required by safety regulations in some countries ) the set should be restored to its original condition and only parts identical to those specified should be used.

Page
	IMPORTANT SERVICE SAFETY PRECAUTION
	ELECTRICAL SPECIFICATIONS
4	LOCATION OF USER'S CONTROL
	INSTALLATION AND SERVICE INSTRUCTIONS
11	CHASSIS LAYOUT
	BLOCK DIAGRAM
	PRINTED WIRING BOARD ASSEMBLIES
	SCHEMATIC DIAGRAM
	REPLACEMENT PARTS LIST
	PACKING OF THE SET

Page 2

INSTALLATION AND SERVICE INSTRUCTIONS

Note: (1) When performing any adjustments to resistor controls and transformers use non-metallic screwdriver or TV alignment tools.
- (2) Before performing adjustment, TV set must be on at least 15 minutes.

CIRCUIT PROTECTION

The receiver is protected by a 4.0A fuse (F701), mounted on PWB-A, wired into one side of the AC line input.

+ 120V DC REGULATOR ADJUST-MENT

The +120V DC Adj. control (R706) is adjusted at the factory. However, should readjustment be required, proceed as follows:

1. Actuate the receiver with 120V AC input voltage.
2. Select a local channel.
3. Connect positive lead of Digital Voltmeter to C712(positive side) on PWB-A; negative lead to chassis ground.
4. Adjust R706 to obtain a + 119V DC reading.
CAUTION: The reading should be within + 119V ± 1VDC to ensure normal function and circuitry reliability.

X-RADIATION PROTECTOR CIRCUIT TEST

1.After service has been performed on the horizontal deflection system, high voltage system, or + B system, test the X-Radiation protection circuit to ascertain proper operation as follows:

1) Apply 120V AC using a variac transformer for accurate input voltage.
2) Allow for warm up and adjust all customer controls for normal picture and sound.
3) Check the voltage of test point TP654. (It's voltage should be about 19.7V DC.)
Apply external 25V DC at TP654 by using an external DC supply, The increased voltage will cause the TV to shut off.
5) Turn on the power again. Unplug the AC power cord, wait 5 seconds, and plug the AC power cord in the outlet again.

Next turn on the power and make sure the image is normal on the screen.

6) If the TV dose not shut off in step 4, the circuit must be repaired before the set is returned to the customer.
2. When the IC2001 or IC2702 has been replaced, recheck the X-ray protector in the following steps.
1) Select a local channel.

Connect a digital voltmeter to TP654 and make sure that the voltmeter reads 19.7±1.5V.
3) Enter the service mode and select service adjustment"S32".
4) Push the CH-UP or CH-DOWN key on the remote control and make sure the data changes. (SPECD33-40)
5) Now take the steps 4, 5 and 6 in the X-radiation protector circuit test.

HIGH VOLTAGE CHECK

High voltage is not adjustable but must be checked to verify that the receiver is operating within safe and efficient design limitations as specified checks should be as follows:

1. Connect an accurate high voltage meter between ground and anode.
2. Operate receiver for at least 15 minutes at 120V AC line voltage, with strong air signal or properly tuned in test signal.
3. Set Service mode on, service No.S19and Bus data D1(Y-mute on).
4. The voltage should be approximately 23.5kV (at zero beam).

If a correct reading cannot be obtained, check circuitry for malfunctioning components. After the voltage test,make Y-mute off (normal mode).

CONNECTING NOTICE

1. The following connecting cords of this model do not have any symbols which identifi the connection points on the PWB.

In servicing this model, Instead the wires of these cords are color-coded as shown in Table 1.

PARTS	SYMBOL	SYMBOL PIN NO./WIRE COLOR
CODE	ON PVVB	1	2	3	4	5
QCNW- 1769PEZZ	GC	GREEN	BROWN	WHITE	WHITE	WHITE
QCNW- 1768PEZZ	YC	YELLOW	BROWN	WHITE	WHITE	-

Table-1

Page 3

The F-series SHARP TVS have most of the analog setup adjustments eliminated. Coil and variable resistor adjustments are now performed digitally by using the remote transmitter or set's volume and channel change function buttons.

Note: There are still a few analog adjustments in the F-series such as 120V adjust, focus, master screen voltage and coils in the picture if/detector circuit.

Follow the steps below whenever service adjustment is required. See table "B" to determine if service adjustments are required.

1.Service mode -

Before putting unit into the service mode, check, that customer adjustments are in the normal mode. use the reset function in the video adjust menu to ensure customer controls are in their proper (reset) position.

To enter the service mode -

Momentarily short TP2001 to TP2002 ( see figure A).

CAUTION: During the adjustment, keep TP2001 and TP2002 short-circuited. Re aware TP2001 to TP2002, be aware that as these test points are shorted they toggle between service and normal. when successfully entered, the service mode will be displayed as shown in figure "B". The "S" figure ( in the left hand bottom corner) stands for service adjustment and the number following "S" is the service adjustment number ( see figure "B"). in the right hand bottom corner is the letter " D" which stands for data,followed by a number which is the digital value of the adjustment

3.Data number selection

Press the volume up or down button to adjust the data number in the lower right hand side of the screen.

To exit service mode-

Turn off the power or unplug the set.

2. Service number selection

Once in the service mode, press the channel up or channel down button on the remote transmitter or at the set. the "S" number ( service adjustment number ) will vary in increments of one, from 1 to 25 (table"A"). Select the item you wish to adjust.

Page 4

		DATA	١	ADJUSTMENT
TOWIDER		INTIAL VALUE	RANGE
S1	SUB-PICTURE	85	0-127
$2	SUB-TINT	70	0-127
$3	SUB-COLOR	50	0-127
S4	SUB-BRIGHTNESS	64	0-127
S5	SHARPNESS	36	0-63
S6	VERTICAL PHASE	0	0-7	Must be set to "0"
S7	HORIZONTAL POSITION	18	0-31
S8	RF-AGC	35	0-63	"0" produces a no picture symptom-black raster
S9	VERTICAL SIZE	32	0-63
S10	vco	60	0-127
S11	R CUT-OFF	0	0-255
S12	G CUT -OFF	0 \|	0-255
S13	B CUT-OFF	ol	0-255
S14	G GAIN	127	0-255
S15	B GAIN	127	0-255
S16	TRAP(3.58MHz)	0	0-1	"0" = ON."1" = OFF
*S17	BPF	1	0-1	"0" = Bandpass.""1" = Take off
*$18	BLANKING	Ó \|	0-1	"0" = Normal."1" = NO Blanking
				"0" = Normal raster."1" = no"Y"
S19	Y-MUTE/VERT,COLLAPSE	0	0-3	"2" = Test mode ."3" = NO Vertical
*S20	HORZ.AFC	1	0-1	"0" = x 2 gain."1" = normal gain
S21	WHITE PEAK LIMITER	1	0-1
*S22	60Hz	0	0-1	"0" = Normal viewing"1" = not available
S25	CAPTION POSITION	23	0-15
$32	X-RAY PROTECTOR	36	33-40

*No adjustment is required due to proper setting being made by IC2001 automatically. Table - A

	ADJU	JSTMENT	NOTES
REPLACED	NECESSARY	UNNECESSARY
IC2001		×	Data is stored in IC2702.
IC201	×		The adjustment is needed to compensate for characteristics of parts including IC201.
IC2702	×		Initial setting values are written from IC2001.Adjust for best results.
CRT	×		Adjust items related to picture tube only.

Table - B

Page 5

Service adjustment

VCO Adjustment

1. Connect a digital voltmeter between pin 44 of IC201 and ground.
2. Select a good local channel.
Enter the service mode. select adjustment "$10".
4. Adjust the data so that digital voltmeter should read 2.2V.
5. Adjustment is complete, remove the voltmeter, return to "normal" mode.

RF AGC Adjustment

1. Have unit receive a good local channel.
2. Enter the service mode and select service adjustment "S8".
3. Set the data value to point where no noise or beat appears.
4. Select another channel to confirm that no noise or beat appears.
NOTE 1 : You will have to come out of the service mode to select another channel.
NOTE 2 : Setting the data to "0" will produce a black raster.

Screen adjustment

1. Connect a digital voltmeter between TP852 and TP853 on the CRT socket PWB.
Note: These test points may not be provided.
- Then connect the voltmeter to both ends of R852 located near Q852 on the foil side.
2. Select a good local channel.
3. Enter the service mode and select service adjustment "S3" and set the data value to "0" to set the color level to minimum. You may skip this step if you selected a B/W picture or monoscope pattern.
4. Select service adjustment "S19" and adjust the data value to "1" this turns off the luminance signal (Y-mute).
5. Select service adjustment "S4" and adjust data value to obtain 0.17volts on the digital voltmeter.

6. Adjust the master screen cotrol untill raster darkens to the point where raster is barely seen.
Adjust service adjustments "S11" red, "S12" green and "S13" blue to obtain a good grey scale with normal whites at low brightness level.
8. Select service adjustment "S19" and reset data to" 0" Select service adjustment "S3" and reset data to obtain normal color level.
9. Remove digital voltmeter. reset master screen cotrol to obtain normal brightness range.

White balance adjustment

1. Have unit receive a good local channel.
Enter the service mode. select service adjustment "S3" and set to "0" (minimum color). "S3" does not have to be adjusted if you selected a B/W picture or monoscope pattern.
Alternately adjust service adjustment data of "$14" and "$15" untill a good grey scale with normal whites is obtained.
4. Select service adjustment "S3" and adjust data to obtain normal color level.

Sub-picture adjustment

1. Have unit receive a good local channel.
2. Make sure the customer picture control is set to maximum.
3. Enter the service mode and select service adjustment "S1".
Adjust the data value to achieve normal contrast range.

Sub-Tint Adjustment

1. Have unit receive a good local channel.
2. Set customer tint control to center of it's range.
3. Enter the service mode and select service adjustment "S2".
4. Adjust "S2" data value to obtain normal flesh tones.

Page 6

Sub-color adjustment

1. Have unit receive a good local channel.
2. Make sure the customer color control is set to center position .
3. Enter the service mode and select service adjustment "S3".
4. Adjust "S3" data value to obtain normal color level.

Sub-brightness adjustment

1. Have unit receive a good local channel.
2. Make sure the customer brightness control is set to center position.
3. Enter the service mode and select service adjustment "S4".
Adjust "S4" data value to obtain normal brightness level.

Vertical-size adjustment

1. Have unit receive a good local channel.
2. Enter the service mode and select service adjustment "S9".
3. While observing the top and bottom of the screen, adjust "S9" data value to proper vertical size and linearity.

Vertical phase adjustment

1. Enter the service mode and select service adjustment "S6".
2. Adjust data value to "0".
Note: This must be set "0" when adjust another data retrace line will be appear.

Horizontal position adjustment

1. Have unit receive a good local channel.
2. Enter the service mode and select service adjustment "S7".
3. Adjust "S7" data value so that picture is centered.

Caption position adjustment (horizontal)

1. Have unit receive a good local channel.
2. Enter the service mode and select service adjustment "S25".
3. A black text box appears on the screen ( see figure C).
4. Adjust "S25" data value so that text box is positioned in the center of the screen.

Flgure-C.

Page 7

Horizontal AFC adjustment

1. Have unit receive a good local channel.
2. Enter service mode and select service adjustment "$20".
3. For normal viewing, adjust data value to "1" which is normal AFC gain.
4. If increased horizontal gain is required, adjust data value to "0" for two times normal gain.

Blanking adjustment

1. Have unit receive a good local channel.
2. Enter the service mode and select service adjustment "$18".
3. This is a two position adjustment, "0" is normal blanking and "1" turns blanking OFF.
4. Adjust data value to " 0" for normal viewing.

White peak limiter (wpl) adjustment

1. Have unit receive a good local channel.
2. Enter the service mode and select service adjustment "S21".
This is a two position adjustment, "1" is ON, "0" is OFF.
4. Adjust data value to "1" for normal viewing.

3.58MHz trap adjustment

1. Have unit receive a good local channel.
2. Enter the service mode and select service adjustment "S16".
This is a two position adjustment, "0" is ON , "1" is OFF.
4. Adjust data value to "0" for normal viewing.

Bandpass filter (BPF) adjustment

1. Have unit receive a good local channel.
2. Enter the service mode and select service adjustment "S17".
3. This is a two position adjustment, "0" is bandpass, "1" is OFF.
4. Adjust data value to "1" for normal viewing.

Sharpness adjustments

1. Have unit receive a good local channel.
2. Enter the service mode and select "S5" for sharpness.
3. Adjust data value to "36" (center of data range) for sharpness adjustment.

60Hz adjustment

1. Have unit receive a good local channel.
2. Enter the service mode and select "S20".
3. The 60Hz adjustment is a two position , "0" is normal viewing. "1" is not used .
4. Adjust data value to "0".
NOTE: If data value is set to "1", you will have a "no sync" condition.

To exit the service mode, turn off power or unplug the set.

Page 8

BLOCK DIAGRAM

Page 9

LOCATION OF USER'S CONTROL

Page 10

SCHEMATIC DIAGRAM: CRT

the second s

		P
	1 1	n .	6
~

Page 11

CHASSIS LAYOUT


1	2	3	4	5	6

Page 12

REPLACEMENT PARTS LIST

SAFETY NOTE — Components marked with a ( A) have special characteristics important to safety. Before replacing any of these components, read carefully the SAFETY NOTICE on page 3 of the Service Manual. Components marked with an (A) are related to X-Ray Protection circuit.

HOW TO ORDER REPLACEMENT PARTS — To have your order filled promptly and correctly, please furnish the following information: 1. MODEL NO. 2. PART NO. 3. DESCRIPTION

Contact your nearest SHARP Parts Distributor to order.

For location of SHARP Parts Distributor, Please call Toll-Free; 1-800-BE-SHARP

Ref. No.	Part No.	*	Description	Code	Ref. No.	Part No.	*	Description	Code
	PICTURE	τι	JBE		P	WB-A DUNT MAIN	К8 U	8605WEV0 NIT
▲ ∆ V101	VBA 3 4 JLN 6 0 X -S	R	CRT	СВ		TU	NEF	2
	or VB 34 KPU 02 X / * S	R	( DY601: H0014PE ) CRT		NOTE:	THE PARTS HERE SH ASSEMBLY BUT NO	IOW T IN	'N ARE SUPPLIED AS AI DEPENDENTLY.	1
	or VB 370 BVBK1U-S or	R	(DY601: H0014PEN1) CRT (DY601: H0008PE	)	▲TU101	VTUVTSH6UZ78	1 /	Tuner	BF
	VB 34JLL40X/ * S	R	CRT	вх		INTEGRATE	) C	RCUITS
	or		(DY601: H0094PE		⚠ IC201	RH-iX2573CEZ	zј	I.C.
			or H1606CEN5)		IC351	VHITDA7233/-	IJ	TDA7233	AF
	VB 37 GDA 86 X /1E	R	CRT		∕ ∆IC501	RH-iX1011CEZ	ΖJ	TA8403K	AG
	RCILHOO14PF77	R	(DYOUT: HUUT4PE) Deflection Yoke	вн	▲ ∧ IC701	RH-iX0137CEZ	ΖJ	T2508	АН
	or	~	(V101: A34JLN60X o	r	1 C751	VHika7809PI-	J	KIA7809PI	AE
			37GDA86X)			or
	RC i LH 0 8 PEZZ	R	Deflection Yoke	BB		VHITA7895/-	1
	or		(V101; CPI370R\/RK111		▲/\IC2001	RH-IX2599CF7	7 J	I.C.	BA
	RC i LH 0 0 1 4 PEN1	R	Deflection Yoke			VHIKIA7045P-1	۰ ۔ ا	KIA7045P	AD
	or		(V101:		▲ A IC2702	RH-IX2447CEN	י 1 ג 1	ST24C01CB1	AL
		_	34PKPU02XX)			VH$$6785GLB1	E J	SI.Controlled Rectifie
	RC \| LH 0111 PEZZ or	R	(V101: CPJ370BVBK1U)
	RC i LH 1 6 0 6CEN5	R	Deflection Yoke	AZ		TRANSI	sтα	DRS
			(V101:		You can su	bstitute for "VS2SC94	540	2/-1"for"V$2$C2815YW	/-1"
	RC i LH 0094 PEZZ	R	Deflection Yoke		O201	V$2$C1906//1	ΞJ	2SC1906	AC
			(V101:		0351	V$2$C945A0/-	IJ	2SC945A(O)	AB
		-	A34JLL40X)		0402	V$2$C945A0/-	- \| ]	2SC945A(O)	AR
/ 1.702	RC I L G 0386PEZZ	R	Degaussing Coil Magnet Ass'y	АК 4 к	0405	V$2$C945A0/-	1 J	2SC945A(0)	ΔR
	FINAL SUUCEZZ	,	- Purity and Static		Q400 0451	V$2$C945A0/-	11	2SC945A(O)	ΔR
			Convergence		▲ ₼ 0722	V$2$C945A0/-	11	2SC945A(O)	AR
	PSPA G 04PEZZ	R	Wedge (Gum), Yoke	AC	02154	V$2$C945A0/-	1 1	2SC945A(O)	ΔR
	OFARC1404PF77	R	Fositioning (3 Used)	ΔD	02155	V$2$C94540/-	1 1	25(9454(0)	ΔR
	MSPRT0001PEFJ	R	Spring for CRT	AC	0401	V$2$61015V/1		2501015(V)
					0402	V$25A10157/1	- J - J	2541015(1)
		Δ		IEC	Q403	V$25A10151/1	с J 1 I	2341013(1)
			N U MJJEIVIDL Ntitem	IEJ	Q DU I	v 5 2 3 C 2 4 8 2 //-	L J	2302482	AD
						v 5 2 5 D 1 5 5 4 / / 1	E J	2501554	AL
PWB-A	DUNTK8605WEV0	-	Main P.W.B. UNIT	—	∕ ΩQ/21	v525C1983//-	2 J	2201983	AF
PWB-B	DUNTK8606WEV0	-	CRT P.W.B. UNIT	—

Page 13

Ret. No.	Part No.	*	Description	Code	Ref. No.	Part No.	+	Description	Code
							:D C
You can s	ubstitute for "RH-DX(	)4460	EZZ"for "VHD1SS11	9//-1	CE201			sound Taka off
(ou cuito	and RH-DX	00450	GEZZ "		CE202	RFILCO267CE77		Sound Take off	AD
D101	RH-EX0701GEZ	ΖJ	Zener Diode,32V	AB	CF302	REILCOO13CEZZ
D102	RH-EX0294CEZ	ΖJ	Zener Diode,5.1V	АА	CE601	RELLADORACEZZ	, .	4.5MHZ
D401	RH-EX0280CEZ	zј	Zener Diode,3V	АА	CE2101			Filter
D451	RH-EX0103CEZ	ΖJ	Zener Diode, 5.6V	AB	SE201	REILCO137CE77
D453	VHD1SS119//-	1 J	1$$119	AB	51201	R112C0137C222		Wave Filter
D454	VHD155119//-	1 J	155119	AB				wave Filter
D706	VHD1$$119//-	1 J	1$$119	АВ
₫ D709	VHD1$$119//-	1 J	1SS119	AB		COL	S
D21 02	VHD1SS119//-	1 J	1$$119	AB	1203	VP-XFR82K0000		0.82 . /H	ΔR
D2103	VHD1SS119//-	1 J	155119	AB	1204	VP-XFR68K0000	1	0.68 u H
D2110	VHD1$$119//-	1 J	1$$119	AB	L206	RCiLi0588CEZZ		IF COIL	ΔF
D455	RH-EX0092CEZ	ΖJ	Zener Diode,3.9V	AB	L207	VP-XF100K000		10 / H
D501	RH-DX0441CEZ	ΖJ	Diode	AC	L403	VP-XF100K000	2 1	10µH	AB
	or				1301	RCILIO605CEZZ	7 \|	SIEDet	ΔF
	RH-DX0110CEZ	z			1401	VP-XF120K000	0 1	12 " H
₫ D65 1	RH-DX0441CEZ	ΖJ	Diode	AC	L402	VP-XF3R3K0000		3.3 u H	AB
	or				L404	VP-XF8R2K0000		8.2 u H	AR
	RH-DX0110CEZ	Z			L405	VP-XF8R2K0000	) ]	8.2 u H	AB
/⚠̀ D502	RH-DX0131CEZ	ΖJ	Diode	AC	L406	VP-XF680K000	0 1	68µH	AB
∕ 1 D751	RH-DX0131CEZ	ΖJ	Diode	AC	L407	VP-XF680K000	0 1	68µH	AB
D602	RH-EX0312CEZ	ΖJ	Zener Diode,9.1V	AA	∕ 1 \L701	RCILF0254CEZZ	: J	Line Filter	AG
D605	RH-EX0312CEZ	ΖJ	Zener Diode,9.1V	AA		or
D2112	RH-EX0312CEZ	ΖJ	Zener Diode,9.1V	AA		RCilF0003PEZZ
D653	RH-EX0313CEZ	ΖJ	Zener Diode,9.1V	AA		or
∕ î∆ D701	RH-DX0154CEZ	ΖJ	1S1887A	AC		RCILF0087CEZZ
∕ 1 D702	RH-DX0154CEZ	ΖJ	1S1887A	AC	L2001	RCILB0131CEZZ	L J	Oscillation Coil	AE
∕ £ D703	RH-DX0154CEZ	ΖJ	1S1887A	AC
/⚠̀ D704	RH-DX0154CEZ	ΖJ	1$1887A	AC
D705	RH-DX0417CEZ	ΖJ	Diode	AE
	or					TRANSFO	RM	IERS
	RH-DX0200CEZ	Z			T601	RTRNZ0073CEZZ	z J	H-Drive	AF
₫ D708	RH-EX0238CEZ	ΖJ	Zener Diode,75V	AC	▲ ⚠ Т60 2	RTRNF0057PEZZ	R	H-Output	вн
D721	RH-EX0019TAZ	ΖJ	Zener Diode	AB	∕ 17701	RTRNP0416CEZZ	L J	Power	AV
∕ £D752	RH-DX0226CEZ	ΖJ	Diode	AC
▲ ⁄î\ D2701	RH-EX0293CEZ	ΖJ	Zener Diode,5.1V	AA

PACKAGED CIRCUIT

ŀ,

∄ PR701	RMPTP0026CEZZ	J	Positive Coefficient	AF
			Thermistor
X801	RCRSB0001PEZZ	R	CRYSTAL,3.58MHz	AL

CONTROL

\Lambda R706	RVR-M4328CEZZ	J	1k(B) 120V Adj.	AC

Page 14

Ref. No.	Part No.	*	-	Descri	ption	Code	Ref. No.	Part No.	*		Descri	otion	Code
	CAPACI	т	ORS				C401	VCKYMN1HB331K	J	330	p 50\	/ Ceramic	АА
C101	VCEAGA1HW225M	J	2.2	50V	EL.	AB	C402	VCKYMN1HB101K	J	100p	50V	Ceramic	AA
C301	VCEAGA1HW225M	J	2.2	50V	EL.	AB	C2117	VCKYMN1HB101K	J	100p	50V	Ceramic	AA
C502	VCEAGA1HW225M	J	2.2	50V	EL.	AB	C2146	VCKYMN1HB101K	J	100p	50V	Ceramic	AA
C516	VCEAGA1HW225M	J	2.2	50V	EL.	AB	C403	VCEAGA1HW105M	J	1.0	50V	EL.	AC
C2007	VCEAGA1HW225M	J	2.2	50V	EL.	AB	C410	VCEAGA1HW105M	J	1.0	50V	EL.	AC
C102	VCEAGA1CW477M	J	470	16V	EL.	AC	C602	VCEAGA1HW105M	J	1.0	50V	EL.	AC
C353	VCEAGA1CW477M	J	470	16V	EL.	AC	C603	VCEAGA1HW105M	J	1.0	50V	EL.	AC
C361	VCEAGA1CW477M	J	470	16V	EL.	AC	C2701	VCEAGA1HW105M	J	1.0	50V	EL.	AC
C724	VCEAGA1CW477M	J	470	16V	EL.	AC	C404	VCEAGA1HW335M	J	3.3	50V	EL.	AB
C752	VCEAGA1CW477M	J	470	16V	EL.	AC	C405	VCEAGA1HW335M	J	3.3	50V	EL.	AB
C103	VCEAGA1VW476M	J	47	35V	EL.	AB	C413	VCEAGA1HW106M	J	10	50V	EL.	AC
C365	VCEAGA1VW476M	J	47	35V	EL.	AB	C715	VCEAGA1HW106M	J	10	50V	EL.	AC
C721	VCEAGA1VW476M	J	47	35V	EL.	AB	C2704	VCEAGA1HW106M	J	10	50V	EL.	AC
C104	VCKYPA1HF103Z	J	0.01	50V	Ceramic	АА	C418	VCKYMN1HB151K	J	150p	50V	Ceramic	AA
C306	VCKYPA1HF103Z	J	0.01	50V	Ceramic	АА	C419	VCCSMN1HL330J	J	33p	50V	Ceramic	AA
C422	VCKYPA1HF103Z	J	0.01	50V	Ceramic	AA	C420	VCCSPA1HL820J	J	82p	50V	Ceramic	AA
C2002	VCKYPA1HF103Z	J	0.01	50V	Ceramic	AA	C421	VCCCMN1HH180J	J	18p	50V	Ceramic	AA
C105	VCSATA1CE226K	J	22	16V	Tantalur	n,AD	C452	VCQYTA1HM563K	J	0.056	50V	Mylar	AB
C201	VCKYMN1HB102K	J	1000	p 50V	Ceramic	АА	C2003	VCQYTA1HM563K	J	0.056	50V	Mylar	AB
C205	VCKYMN1HB102K	J	1000	p 50V	Ceramic	AA	C2004	VCQYTA1HM563K	J	0.056	50V	Mylar	AB
C206	VCKYMN1HB102K	J	1000	p 50V	Ceramic	AA	C501	VCSATA1CE225K	J	2.2	16V	Tantalun	n AB
C305	VCKYMN1HB102K	J	1000	p 50V	Ceramic	АА	C503	VCFYHA1HA274J	J	0.27	50V	Mylar	AC
C713	VCKYMN1HB102K	J	1000	p 50V	Ceramic	AA	C504	VCKYPA2HB391K	J	390p	500V	Ceramic	AA
C204	VCKYMN1CY103N	J	0.01	16V	Ceramic	AA	C505	VCQYTA1HM473K	J	0.047	50V	Mylar	AB
C210	VCKYMN1CY103N	J	0.01	16V	Ceramic	AA	C507	VCQYTA1HM103K	J	0.01	50V	Mylar	AB
C213	VCKYMN1CY103N	J	0.01	16V	Ceramic	AA	C510	VCQYTA1HM103K	J	0.01	50V	Mylar	AB
C415	VCKYMN1CY103N	J	0.01	16V	Ceramic	АА	C601	VCQYTA1HM103K	J	0.01	50V	Mylar	AB
C416	VCKYMN1CY103N	J	0.01	16V	Ceramic	AA	▲ ∧ C714	VCQYTA1HM103 K	J	0.01	50V	Mylar	AB
C2005	VCKYMN1CY103N	J	0.01	16V	Ceramic	AA	C512	VCEACA1HC335M	J	3.3	50V	EL.	AB
C207	VCEAGA1HW474M	J	0.47	50V	EL.	AA	C513	VCEAGA1EW477M	J	470	25V	EL.	AD
C211	VCEAGA1HW474M	J	0.47	50V	EL.	AA	C514	VCEAGA1VW477M	J	470	35V	EL.	AD
C802	VCEAGA1HW474M	J	0.47	50V	EL.	AA	C710	VCEAGA1VW477M	J	470	35V	EL.	AD
C209	VCEAGA1CW227M	J	220	16V	EL.	AC	C515	VCKYPA2HB102K	J	1000	p500V	Ceramic	AA
C214	VCEAGA1CW227M	J	220	16V	EL.	AC	C651	VCKYPA2HB102K	J	1000	p500V	Ceramic	AA
C212	VCKYMN1CX222M	J	2200	p16V	Ceramic	AA	C756	VCKYPA2HB102K	J	1000	p500V	Ceramic	AA
C302	VCQYTA1HM472K	J	4700	p 50V	Mylar	AB	▲ ∧ C605	RC-KZ0340CEZZ	J	820p	2kV C	eramic	AD
C351	VCE9GA1HW225M	J	2.2	50V	EL. (N.P)	AB		or
C352	VCEAGA1VW107M	J	100	35V	EL.	AC		RC-KZ0040CEZZ
C508	VCEAGA1VW107M	J	100	35V	EL.	AC	▲ ∧ C606	VCFPPD3CA682J	J	6800	p 160	0V	AE
C2001	VCEAGA1VW107M	J	100	35V	EL.	AC				Meta	alized F	olypro Fil	m
C354	VCQYTA1HM104K	J	0.1	50V	Mylar	AC	C608	VCFPPD2DB334J	J	0.33	200V		AF
C407	VCQYTA1HM104K	j	0.1	50V	Mylar	AC				Meta	alized I	Polypro Fil	m
C412	VCQYTA1HM104K	J	0.1	50V	Mylar	AC	C609	VCKYPA2HB222K	j	2200	p500V	Ceramic	AA
C355	VCEAGA1VW226M	J	22	35V	EL.	ΑΑ	C611	VCCSPA2HL180K	J	18p	500V	Ceramic	AA
C453	VCEAGA1VW226M	J	22	35V	EL.	АА	C652	VCEAGA1HW475M	J	4.7	50V	EL.	AB
C363	VCQYTA1HM682K	Ĵ	6800	0p50V	Mylar	AB	C2145	VCEAGA1HW475M	J	4.7	50V	EL.	AB
C366	VCCSPA1HL330J	j	33p	50V	Ceramic	AA

Page 15

▲ C701 C702 C703 C704 ▲ C705 ▲ C712 C717 C718 C719 C725 C751 C754 C801 C803 C805	RC-FZ002SCEZZ or RC-QZ005SCEZZ or RC-FZ004SGEZZ VCKYPB2HE103P VCKYPB2HE103P VCKYPB2HE103P RC-EZ0423CEZZ or RC-EZ0183CEZZ VCQPSB2DA473K VCQPSB2DA473K VCKYPA2HB151K VCKYPA2HB332K VCKYPA2HB152K VCEAGA2EW106M VCEAGA1CW337M		0.47 0.01 0.01 620 560 100 0.047 150p 3300p	AC1: 500V 500V 200V 200V 200V 160V 200V 500V	25V Plastic Ceramic Ceramic EL. EL. EL. EL. Polypro	AB AB AB AP AG AB	RJ32 RJ33 RJ35 RJ36 R101 ▲ R652 R2008 ▲ R2019 R2127 R2147 R102 ▲ R103 ▲ R104 R105	VRD-MN2BE000J VRD-MN2BE000J VRD-MN2BE000J VRD-MN2BE000J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE110J VRS-VV3DB151J	ו ו ו ו ו ו ו ו ו ו ו ו ו ו ו ו ו ו ו	0 0 0 10k 10k 10k 10k 10k 1.0 150 15k	1/8 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1	W Carbon V Carbon V Carbon V Carbon V Carbon V Carbon V Carbon V Carbon V Carbon V Carbon V Carbon V Carbon Metal Oxide	AA
C702 C703 C704 ▲ C705 ▲ C712 C717 C718 C719 C725 C751 C754 C801 C803 C805	or RC-QZ005SCEZZ or RC-FZ004SGEZZ VCKYPB2HE103P VCKYPB2HE103P VCKYPB2HE103P RC-EZ0423CEZZ or RC-EZ0183CEZZ or RC-EZ0523CEZZ VCQPSB2DA473K VCQPSB2DA473K VCKYPA2HB151K VCKYPA2HB332K VCKYPA2HB152K	ו ר ר ר ר ר ר ר ר ר	0.01 0.01 620 560 100 0.047 150p 3300p	500V 500V 200V 200V 200V 160V 200V 500V	Ceramic Ceramic EL. EL. EL. EL. Polypro	AB AB AP AG AB	RJ33 RJ35 RJ36 R101 ▲ R652 R2008 ▲ R2019 R2127 R2147 R102 ▲ R103 ▲ R104 R105	VRD-MN2BE000J VRD-MN2BE000J VRD-MN2BE000J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE110J VRS-VV3DB151J	ו ו ו ו ו ו ו ו	0 0 10k 10k 10k 10k 10k 10k 1.0 150	1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W	V Carbon V Carbon V Carbon V Carbon V Carbon V Carbon V Carbon V Carbon V Carbon V Carbon Metal Oxide	AA
C702 C703 C704 ▲ C705 ▲ C712 C717 C718 C719 C725 C751 C754 C801 C803 C805	RC-QZ005SCEZZ or RC-FZ004SGEZZ VCKYPB2HE103P VCKYPB2HE103P VCKYPB2HE103P RC-EZ0423CEZZ or RC-EZ0183CEZZ RC-EZ0523CEZZ RC-EZ0578CEZZ VCQPSB2DA473K VCKYPA2HB151K VCKYPA2HB152K VCKYPA2HB152K VCEAGA2EW106M VCEAGA1CW337M	ו ו ו ו ו ו ו ו ו ו ו ו	0.01 0.01 620 560 100 0.047 150p 3300p	500V 500V 200V 200V 200V 160V 200V 500V	Ceramic Ceramic EL. EL. EL. EL. Polypro	AB AB AP AG AB	RJ35 RJ36 R101 ▲ ▲ R652 R2008 ▲ ▲ R2019 R2127 R2147 R102 ▲ R103 ▲ R104 R105	VRD-MN2BE000J VRD-MN2BE000J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE1R0J VRS-VV3DB151J	ו ו ו ו ו ו ו ו	0 10k 10k 10k 10k 10k 10k 1.0 150	1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W	✓ Carbon ✓ Carbon ✓ Carbon ✓ Carbon ✓ Carbon ✓ Carbon ✓ Carbon ✓ Carbon ✓ Carbon ✓ Carbon ✓ Metal Oxide	AA
C702 C703 C704 ▲ C705 ▲ C712 C717 C718 C719 C725 C751 C754 C801 C803 C805	or RC-FZ004SGEZZ VCKYPB2HE103P VCKYPB2HE103P RC-EZ0423CEZZ or RC-EZ0183CEZZ or RC-EZ0523CEZZ RC-EZ0378CEZZ VCQPSB2DA473K VCKYPA2HB151K VCKYPA2HB332K VCKYPA2HB152K VCEAGA2EW106M VCEAGA1CW337M	ו ו ר ו ר ו ר ו ר ו ר	0.01 0.01 620 620 560 100 0.047 150p 3300p	500V 500V 200V 200V 200V 160V 200V 500V	Ceramic Ceramic EL. EL. EL. EL. EL.	AB AB AP AG AB	RJ36 R101 ▲ ♠ R652 R2008 ▲ ♠ R2019 R2127 R2147 R102 ♠ R103 ♠ R104 R105	VRD-MN2BE000J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE1R0J VRS-VV3DB151J	ו ו ו ו ו ו ו ו	0 10k 10k 10k 10k 10k 1.0 150 15k	1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 2W 2W	/ Carbon / Carbon / Carbon / Carbon / Carbon / Carbon / Carbon / Carbon Metal Oxide	AA AA AA AA AA AA AA AA AA AA
C702 C703 C704 ▲ C705 ▲ C712 C717 C718 C719 C725 C751 C754 C801 C803 C805	VCKYPB2HE103P VCKYPB2HE103P VCKYPB2HE103P RC-EZ0423CEZZ or RC-EZ0183CEZZ RC-EZ0523CEZZ RC-EZ0378CEZZ VCQPSB2DA473K VCKYPA2HB151K VCKYPA2HB332K VCKYPA2HB152K VCEAGA2EW106M VCEAGA1CW337M	ו ו ( ו ( ו ( ו ( ו ( ו (	0.01 0.01 620 560 100 0.047 150p 3300p	500V 500V 200V 200V 200V 160V 200V 500V	Ceramic Ceramic EL. EL. EL. EL. Polypro	AB AB AP AG AB	R101 ▲ R652 R2008 ▲ R2019 R2127 R2147 R102 ▲ R103 ▲ R104 R105	VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE1R0J VRS-VV3DB151J VRS-VV3DB153J	ו ו ו ו ו ו ו	10k 10k 10k 10k 10k 10k 1.0 150 15k	1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 2W 2W	/ Carbon / Carbon / Carbon / Carbon / Carbon / Carbon / Carbon Metal Oxide	AA AA AA AA AA AA AA AA
C702 C703 C704 ▲ C705 ▲ C712 C717 C718 C719 C725 C751 C754 C801 C803 C805	VCKYPB2HE103P VCKYPB2HE103P RC-EZ0423CEZZ or RC-EZ0183CEZZ RC-EZ0523CEZZ RC-EZ0378CEZZ VCQPSB2DA473K VCKYPA2HB151K VCKYPA2HB332K VCKYPA2HB152K VCEAGA2EW106M VCEAGA1CW337M	ו ו ( ו ( ו ( ו ( ו (	0.01 0.01 620 620 560 100 0.047 150p 3300p	500V 500V 200V 200V 200V 160V 200V 500V	Ceramic Ceramic EL. EL. EL. EL. Polypro	AB AB AP AP AG AB	▲ A R652 R2008 ▲ R2019 R2127 R2147 R102 A R103 A R104 R105	VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE1R0J VRS-VV3DB151J VRS-VV3DB153J	ו ו ו ו ו ו	10k 10k 10k 10k 10k 1.0 150 15k	1/8W 1/8W 1/8W 1/8W 1/8W 2W 2W	/ Carbon / Carbon / Carbon / Carbon / Carbon / Carbon Metal Oxide	AA AA AA AA AA AA AA
C703 C704 ▲ C705 ▲ C705 C712 C717 C718 C719 C725 C751 C754 C801 C803 C805	VCKYPB2HE103P VCKYPB2HE103P RC-EZ0423CEZZ or RC-EZ0183CEZZ RC-EZ0523CEZZ RC-EZ0378CEZZ VCQPSB2DA473K VCKYPA2HB151K VCKYPA2HB332K VCKYPA2HB332K VCKYPA2HB152K VCEAGA2EW106M VCEAGA1CW337M	ו ו ( ו ( ו ( ו ( ו (	0.01 0.01 620 620 560 100 0.047 150p 3300p	500V 500V 200V 200V 200V 160V 200V 500V	Ceramic Ceramic EL. EL. EL. EL. Polypro	AB AB AP AG AB	R2008 ▲ R2019 R2127 R2147 R102 ▲ R103 ▲ R104 R105	VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE1R0J VRS-VV3DB151J VRS-VV3DB153J	ו ו ו ו ו	10k 10k 10k 10k 1.0 150 15k	1/8W 1/8W 1/8W 1/8W 2W 2W	/ Carbon / Carbon / Carbon / Carbon / Carbon Metal Oxide	AA AA AA AA AA AA AA
▲ C704 ▲ C705 ▲ C712 C717 C718 C719 C725 C751 C754 C801 C803 C805	RC-EZ0423CEZZ or RC-EZ0183CEZZ or RC-EZ0523CEZZ RC-EZ0378CEZZ VCQPSB2DA473K VCKYPA2HB151K VCKYPA2HB332K VCKYPA2HB152K VCEAGA2EW106M VCEAGA1CW337M	ו ו ו ו ו ו ו ו ו ו ו ו ו ו ו ו ו ו ו	620 620 560 100 0.047 150p 3300p	200V 200V 200V 200V 160V 200V 500V	EL. EL. EL. EL. Polypro	AB AP AG AB	▲ A R2019 R2127 R2147 R102 A R103 A R104 R105	VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE1R0J VRS-VV3DB151J VRS-VV3DB153J	ו ו ו ו	10k 10k 10k 1.0 150 15k	1/8W 1/8W 1/8W 2W 2W	/ Carbon / Carbon / Carbon / Carbon Metal Oxide	AA AA AA AA AA AA
▲ C712 C717 C718 C719 C725 C751 C754 C801 C803 C805	RC-EZ0423CEZZ or RC-EZ0183CEZZ RC-EZ0523CEZZ RC-EZ0378CEZZ VCQPSB2DA473K VCKYPA2HB151K VCKYPA2HB151K VCKYPA2HB152K VCEAGA2EW106M VCEAGA1CW337M	ו נ ( ן ( ן ( ן	620 560 100 0.047 150p 3300p	200V 200V 200V 160V 200V 500V	EL. EL. EL. EL. Polypro	AP AG AB	R2127 R2147 R102 AR103 AR104 R105	VRD-MN2BE103J VRD-MN2BE103J VRD-MN2BE1R0J VRS-VV3DB151J VRS-VV3DB153J	ן ו ו ו	10k 10k 1.0 150 15k	1/8W 1/8W 1/8W 2W 2W	Carbon Carbon Carbon Metal Oxide	AA AA AA AA AA
▲ C712 C717 C718 C719 C725 C751 C754 C801 C803 C805	or RC-EZ0183CEZZ or RC-EZ0523CEZZ RC-EZ0378CEZZ VCQPSB2DA473K VCKYPA2HB151K VCKYPA2HB332K VCKYPA2HB332K VCKYPA2HB152K VCEAGA2EW106M VCEAGA1CW337M	ו ו ו ו ו ו ו ו	620 560 100 0.047 150p 3300p	200V 200V 160V 200V 500V	EL. EL. EL. Polypro	AG AB	R2147 R102 介 R103 介 R104 R105	VRD-MN2BE103J VRD-MN2BE1R0J VRS-VV3DB151J VRS-VV3DB153J	ן ו ו ו	10k 1.0 150 15k	1/8W 1/8W 2W 2W	'Carbon 'Carbon Metal Oxide Metal Oxide	AA AA AA AA
▲ C712 C717 C718 C719 C725 C751 C754 C801 C803 C805	or RC-EZ0523CEZZ RC-EZ0378CEZZ VCQPSB2DA473K VCKYPA2HB151K VCKYPA2HB332K VCKYPA2HB152K VCKYPA2HB152K VCEAGA2EW106M VCEAGA1CW337M	ו ו ו ו ו ו ו ו ו ו ו ו ו ו ו ו ו ו ו	560 100 0.047 150p 3300p	200V 200V 160V 200V 500V	EL. EL. Polypro	AG AB	R102	VRD-MN2BE1R0J VRS-VV3DB151J VRS-VV3DB153J	1 1 1	1.0 150 15k	1/8W 2W 2W	′Carbon Metal Oxide Metal Oxide	AA AA AA
▲ C712 C717 C718 C719 C725 C751 C754 C801 C803 C805	RC-EZ0523CEZZ RC-EZ0378CEZZ VCQPSB2DA473K VCKYPA2HB151K VCKYPA2HB332K VCKYPA2HB152K VCKYPA2HB152K VCEAGA2EW106M VCEAGA1CW337M	ו ר ר ו ר ו ר	560 100 0.047 150p 3300p	200V 160V 200V 500V	EL. EL. Polypro	AG AB	⚠े R103 ⚠े R104 R105	VRS-VV3DB151J VRS-VV3DB153J	1 1	150 15k	2W 2W	Metal Oxide Metal Oxide	AA AA
▲ C712 C717 C718 C719 C725 C751 C754 C801 C803 C805	RC-EZ0378CEZZ RC-EZ0378CEZZ VCQPSB2DA473K VCKYPA2HB151K VCKYPA2HB332K VCKYPA2HB152K VCEAGA2EW106M VCEAGA1CW337M	ו ו ו ו ו ו ו ו	100 0.047 150p 3300p	160V 200V 500V	EL. Polypro	AG AB	∕ ∧ R104 R105	VRS-VV3DB153J	J	15k	2W	Metal Ovide	AA
C717 C718 C719 C725 C751 C754 C801 C803 C805	VCQPSB2DA473K VCKYPA2HB151K VCKYPA2HB332K VCKYPA2HB152K VCEAGA2EW106M VCEAGA1CW337M	ו 1 1 1 1	0.047 150p 3300p	200V 500V	Polypro	AG	R105					wie tar Oxide
C718 C719 C725 C751 C754 C801 C803 C805	VCKYPA2HB151K VCKYPA2HB332K VCKYPA2HB332K VCKYPA2HB152K VCEAGA2EW106M VCEAGA1CW337M	ו 1 1 : 1	0.047 150p 3300p	200v	Polypro	AB		VRD-MN2BE823J	J	82k	1/8W	Carbon	АА
C719 C725 C751 C754 C801 C803 C805	VCKYPA2HB131K VCKYPA2HB332K VCKYPA2HB152K VCEAGA2EW106M VCEAGA1CW337M	ו 1 1 :	130p 3300p	2004	Commin		R2003	VRD-MN2BE823J	J	82k	1/8W	Carbon	ΑΑ
C719 C725 C751 C754 C801 C803 C805	VCKYPA2HB332K VCKYPA2HB152K VCEAGA2EW106M VCEAGA1CW337M	J.	3300p		Ceramic		R2142	VRD-MN2BE823J	J	82k	1/8W	Carbon	АА
C725 C751 C754 C801 C803 C805	VCEAGA2EW106M VCEAGA1CW337M	1 T		5000	Ceramic	АВ	R106	VRD-RA2BE121J	J	120	1/8W	Carbon	ΔΔ
C754 C801 C803 C805	VCEAGA1CW337M	1	1500p	500V	Ceramic	AA	R107	VRD-RA2BE121J	j	120	1/8W	Carbon	AA
C754 C801 C803 C805	VCEAGATCW337M		10	2500	EL.	AC	R207	VRD-RA2BE121J	j	120	1/8W	Carbon	ΔΔ
C803	VCOVT & 411843331	1	330	160	EL.	AC	R901	VRD-RA2BE121J	J	120	1/8W	Carbon	AA
C803	VCQTIATHM223J	ינ	12-	500	Niylar Comortio		R902	VRD-RA2BE121J	J	120	1/8W	Carbon	AA
			12p	500	Ceramic		R201	VRD-MN2BE151J	J	150	1/8W	Carbon	AA
C806	VCEAGA1HW104M		0.1	500			R202	VRD-MN2BE122J	J	1.2k	1/8W	Carbon	АА
C800	VCEAGA1HW104M		0.1	501	EL.		R417	VRD-MN2BE122J	J	1.2k	1/8W	Carbon	АА
C2109			0.1 470n	501	Coramic		R203	VRD-MN2BE682J	J	6.8k	1/8W	Carbon	АА
C2103		, , , ,	470p	501	Coramic	~~	R423	VRD-MN2BE682J	J	6.8k	1/8W	Carbon	AA
C2110		, , , ,	470p	501	Coromic		R462	VRD-MN2BE682J	J	6.8k	1/8W	Carbon	АА
C2112			470p	500	Coramic		R204	VRD-MN2BE470J	J	47	1/8W	Carbon	AA
C2112			470p	50*	Cerannic	~~	R206	VRD-MN2BE152J	J	1.5k	1/8W	Carbon	АА
							R418	VRD-MN2BE152J	J	1.5k	1/8W	Carbon	АА
							R453	VRD-MN2BE152J	J	1.5k	1/8W	Carbon	АА
	RESISTO	RS					R208	VRD-MN2BE471J	J	470	1/8W	Carbon	АА
RJ2	VRD-MN2BE000J		) 1	/8W (	arbon	۵۵	R409	VRD-MN2BE471J	J	470	1/8W	Carbon	AA
RJ6	VRD-MN2BE000J	. (	) 1	/8W (	arbon		R504	VRD-MN2BE471J	J	470	1/8W	Carbon	AA
RJ8	VRD-MN2BE0001		) 1	/8W (	Tarbon	ΔΔ	R209	VRD-MN2BE331J	J	330	1/8W	Carbon	AA
RJ9	VRD-MN2BE000J	J	) 1	/8W 0	Carbon	ΔΔ	R401	VRD-MN2BE331J	J	330	1/8W	Carbon	AA
RJ14	VRD-MN2BE000J	J	) 1	/8W (	Carbon	ΔΔ	R609	VRD-MN2BE331J	٦	330	1/8W	Carbon	AA
RJ15	VRD-MN2BE000J	JO	) 1	/8W (	Tarbon	ΔΔ	R2146	VRD-MN2BE331J	l	330	1/8W	Carbon	AA
RJ16	VRD-MN2BE000J	J	) 1	/8W (	Carbon	ΔΔ	R303	VRD-MN2BE102J	J	1.0k	1/8W	Carbon	AA
RJ20	VRD-MN2BE000J	J	) 1	/8W (	Carbon	ΔΔ	R407	VRD-MN2BE102J	J	1.0k	1/8W	Carbon	AA
RJ22	VRD-MN2BE000J	1 (	) 1	/8W (	arbon		R408	VRD-MN2BE102J	J	1.0k	1/8W	Carbon	AA
RJ25	VRD-MN2BE0001	יי יו	) 1	/8W (	Tarbon	ΔΔ	R416	VRD-MN2BE102J	١	1.0k	1/8W	Carbon	AA
RJ26	VRD-MN2BE0001	יי וו	) 1	/8W (	arbon	ΔΔ	R2006	VRD-MN2BE102J	J	1.0k	1/8W	Carbon	AA
R127	VRD-MN28F0001	, c 1 c	, 1	/8\// (	arbon	~~ ~	R2007	VRD-MN2BE102J	J	1.0k	1/8W	Carbon	AA
RJ28 V		, c , c	2 I. 1 1	/8\// (	arbon	~~	R2112	VRD-MN2BE102J	J	1.0k	1/8W	Carbon	AA
RJ30	VRD-MN2BE0001		, 1. } 1	/8W/ C	arbon	~~ A A	R2113	VRD-MN2BE102J	J	1.0k	1/8W	Carbon ,	AA
RJ31 V	VRD-MN2BE0001		, i	/8.W/ C	arbon	~~ ^ ^	R2116	VRD-MN2BE102J	J	1.0k	1/8W	Carbon ,	4 A
			. 1			~~~	R2125	VRD-MN2BE102J	J	1.0k	1/ 8W	Carbon /	4 A

ł.

Page 16

Ref. No.	Part No.	*	r	Description	Code	Ref. No.	Part No.	*		Description	Code
P 2122		1	1.04	1/8W Carbon		R2703	VRD-MN2BE101J	J	100	1/8W Carbon	AA
R2132	VRD-MN2BE1021	1	1.0k	1/8W Carbon		R506	VRD-RA2BE683G	J	68k	1/8W Carbon	AA
R2135	VRD-MN2BE102	Ţ	1.0k	1/8W Carbon	ΔΔ	R507	VRD-RA2BE104G	J	100k	1/8W Carbon	АА
▲ A 82150	VRD-MN2BE1021	Ĩ	1.0k	1/8W Carbon	ΔΔ	R508	VRD-MN2BE473J	J	47k	1/8W Carbon	АА
R2152	VRD-MN2BE1021	1	1.0k	1/8W Carbon		R2004	VRD-MN2BE473J	J	47k	1/8W Carbon	АА
R2201	VRD-MN2BE102	í	1.0k	1/8W Carbon	AA	R2128	VRD-MN2BE473J	J	47k	1/8W Carbon	АА
R2207	VRD-MN2BE102J	j	1.0k	1/8W Carbon	AA	R511	VRD-RM2HD681J	J	680	1/2W Carbon	АА
R310	VRD-MN2BE153J	j	15k	1/8W Carbon	AA	R712	VRD-RM2HD681J	J	680	1/2W Carbon	AA
R351	VRD-MN2BE821J	j	820	1/8W Carbon	АА	R514	VRD-RM2HD1R5J	J	1.5	1/2W Carbon	AA
R352	VRD-MN2BE4R7J	j	4.7	1/8W Carbon	АА	∕ AR515	VRN-SV2HB1R0J	J	1.0	1/2W Metal Film
R355	VRD-MN2BE822J	j	8.2k	1/8W Carbon	AA	R516	VRD-RA2BE223G	J	22k	1/8W Carbon	AA
R357	VRD-RA2BE333J	j	33k	1/8W Carbon	AA	R517	VRD-RA2BE154J	J	150k	1/8W Carbon	AA
R703	VRD-RA2BE333J	J	33k	1/8W Carbon	AA	▲ ↑ R707	VRD-RA2BE154J	٦	150k	1/8W Carbon	АА
R358	VRD-RA2BE152J	J	1.5k	1/8W Carbon	АА	R518	VRD-RA2BE123G	J	12k	1/8W Carbon	АА
R603	VRD-RA2BE152J	J	1.5k	1/8W Carbon	AA	R521	VRD-RA2BE273J	J	27k	1/8W Carbon	AA
R402	VRD-MN2BE391J	J	390	1/8W Carbon	AA	R524	VRD-MN2BE332J	J	3.3k	1/8W Carbon	AA
R604	VRD-MN2BE391J	J	390	1/8W Carbon	AA	R801	VRD-MN2BE332J	J	3.3k	1/8W Carbon	AA
R404	VRD-MN2BE330J	J	33	1/8W Carbon	AA	R2130	VRD-MN2BE332J	J	3.3k	1/8W Carbon	AA
R406	VRD-RA2BE680J	J	68	1/8W Carbon	АА	R525	VRD-RA2BE473J	J	47k	1/8W Carbon	AA
R410	VRD-MN2BE562J	J	5.6k	1/8W Carbon	АА	R607	VRD-RM2HD101J	J	100	1/2W Carbon	AA
R438	VRD-MN2BE562J	J	5.6k	1/8W Carbon	АА	R608	VRD-RA2BE471J	J	470	1/8W Carbon	AA
R459	VRD-MN2BE562J	J	5.6k	1/8W Carbon	АА	R610	VRD-RM2HD332J	J	3.3k	1/2W Carbon	AA
▲ / R727	VRD-MN2BE562J	J	5.6k	1/8W Carbon	АА	∕ AR611	VRS-SV3LB152J	J	1.5k	3.0W Metal Oxic	leAB
R411	VRD-MN2BE563J	J	56k	1/8W Carbon	AA	∕ R612	VRN-VV3ABR22J	J	0.22	1W Metal Filn	n AA
R412	VRD-RA2BE391J	J	390	1/8W Carbon	AA	▲ / \ R651	VRD-RM2HD1R0J	٦	1.0	1/2W Carbon	AA
R413	VRD-MN2BE820J	J	82	1/8W Carbon	AA	∕ AR655	VRS-VV3AB682J	J	6.8k	1W Metal Oxide	AA
R414	VRD-MN2BE820J	J	82	1/8W Carbon	AA	∕ 1 R701	VRD-RM2HD824J	J	820k	1/2W Carbon	AA
R415	VRD-MN2BE820J	J	82	1/8W Carbon	AA	∕ 1 R702	VRW-KQ3HC1R5K	J	1.5	5W Cement	AE
R419	VRD-MN2BE472J	J	4.7k	1/8W Carbon	AA	R704	VRD-RM2HD273J	٦	27k	1/2W Carbon	AA
R439	VRD-MN2BE333J	J	33k	1/8W Carbon	AA	▲ / R705	VRD-RA2EE104G	J	100k	1/4W Carbon	AA
R2143	VRD-MN2BE333J	J	33k	1/8W Carbon	AA	▲ / 1 R708	VRD-RA2EE562G	J	5.6k	1/4W Carbon	AA
R2701	VRD-MN2BE333J	J	33k	1/8W Carbon	AA	R709	VRD-MN2BE123J	J	12k	1/8W Carbon	AA
R440	VRD-RA2BE821J	J	820	1/8W Carbon	AA	R2002	VRD-MN2BE123J	٦	12k	1/8W Carbon	AA
R657	VRD-RA2BE821J	J	820	1/8W Carbon	AA	R2140	VRD-MN2BE123J	J	12k	1/8W Carbon	AA
R441	VRD-MN2BE222J	J	2.2k	1/8W Carbon	AA	R2141	VRD-MN2BE123J	J	12k	1/8W Carbon	AA
R451	VRD-RA2BE472J	J	4.7k	1/8W Carbon	AA	R710	VRD-RAZEE123J	J	12k	1/4W Carbon	AA
R605	VRD-RA2BE472J	j	4.7k	1/8W Carbon	AA	R711	VRS-SV2HC470J	J	47	1/2W Metal Oxid	eAA
∕ 1 R452	VRC-MA2HG562K	J	5.6k	1/2W Solid	AA	∕ 1∖R713	VRD-RM2HD330J	J	33	1/2W Carbon	AA
∕ 1 R454	VRS-SV2HC103J	J	10k	1/2W Metal Oxid	leAA	∕ 1. R715	VRS-SV2HC151J	J	150	1/2W Metal Oxid	eAA
R455	VRD-RA2BE274J	J	270k	1/8W Carbon	AA	A R716	VRW-KQ3HC331K	J	330	5W Cement	AE
R456	VRD-RA2BE274J	J	270k	1/8W Carbon	AA	∕n R717	VRW-KQ4AC6R8K	1	6.8	10W Cement	AF
R457	VRD-MN2BE392J	J	3.9k	1/8W Carbon	AA	R721	VKD-KM2HD331J	J	330	1/2W Carbon	AA
R501	VRD-RA2BE102J	J	1.0k	1/8W Carbon	AA	A R729	VRS-VV3DB220J	J	22	2W Metal Oxide	e AA
R505	VRD-MN2BE101J	J	100	1/8W Carbon	AA	∕n R751	VRS-VV3AB390J	٦	39	1W Metal Oxide	e AA
R2009	VRD-MN2BE101J	٦	100	1/8W Carbon	AA	∕1 \R752	VRN-VV3AB1R8J	J	1.8	1W Metal Film	1 AA
R2011	VRD-MN2BE101J	J	100	1/8W Carbon	AA	∕n R754	VRN-RV3AB1R0J	J	1.0	1W Metal Film	n AB
R2702	VRD-MN2BE101J	J	100	1/8W Carbon	AA	∧ R/55	VRS-VV3AB470J	J	47	1W Metal Oxide	e AA
						R2001	VRD-MN2BE683J	J	68k	1/8W Carbon	AA

Page 17

1	3	G	-	N	N	6	0

Code

лн

Ref. No.	Part No.	*		Descri	ption	Code	Ref. No.	Part No.	*	Descript
R2005	VRD-MN2BE183J	J	18k	1/8W	Carbon	АА	▲ ↑ RY701	RRLYU0022CEZZ	J	Relay, Power
R21 49	VRD-MN2BE183J	J	18k	1/8W	Carbon	AA		or
R2012	VRD-MN2BE272J	J	2.7k	1/8W	Carbon	AA		RRLYU0031CEZZ
R2013	VRD-RA2BE182J	J	1.8k	1/8W	Carbon	АА	$2001	QSW-K0079GEZZ	J	Switch,Power
R2014	VRD-MN2BE182J	J	1.8k	1/8W	Carbon	AA	S2002	QSW-K0079GEZZ	J	Switch,CH-up
R2015	VRD-MN2BE182J	J	1.8k	1/8W	Carbon	AA	S2003	QSW-K0079GEZZ	J	Switch,CH-do
R2018	VRD-RA2BE183J	J	18k	1/8W	Carbon	AA	$2004	QSW-K0079GEZZ	J	Switch,VOL-u
R2153	VRD-RA2BE183J	J	18k	1/8W	Carbon	AA	$2005	QSW-K0079GEZZ	J	Switch,VOL-d
R2111	VRD-RM2HD223J	J	22k	1/2W	Carbon	АА	۸	RUNTK0476CEZZ	J	Antenna Box
R212 9	VRD-RM2HD223J	J	22k	1/2W	Carbon	AA
R2115	VRD-MN2BE224J	J	220k	1/8W	Carbon	AA			/0	COCINIEN
R2118	VRD-RA2BE153J	J	15k	1/8W	Carbon	АА	P	WR-R DONIS	(8)	6U6VVEV
R2119	VRD-RA2BE682J	J	6.8k	1/ 8W	Carbon	AA		CRIU	NI
R2120	VRD-RA2BE682J	J	6.8k	1/8W	Carbon	ΑΑ
R2121	VRD-RA2BE682J	J	6.8k	1/ 8W	Carbon	AA		IKANSIS	10	RS
R2122	VRD-RA2BE682J	j	6.8k	1/8W	Carbon	AA	Q852	V$2$C22290/1E	J	2SC2229(O)
▲ ↑ R2131	VRN-RA2BK223F	J	22k	1/8W	Metal Film	AB	Q854	V$2$C22290/1E	ر	2SC2229(O)
▲ ♪ R21 3 7	VRN-RA2BK473F	J	47k	1/8W	Metal Film	АА	Q856	V$2$C22290/1E	J	2SC2229(O)
▲ ∧ R2139	VRN-RA2BK823F	J	82k	1/8W	Metal Film	ΑΑ	Q881	V$2$A1015Y/1E	J	2SA1015(Y)
R2154	VRD-RA2BE123J	J	12k	1/8W	Carbon	АА
R2155	VRD-RA2BE103J	J	10k	1/8W	Carbon	АА
R2156	VRD-RA2BE103J	J	10k	1/8W	Carbon	AA		DIOD	ES
∕ ↑ R2704	VRS-VV3AB331J	J	330	1W Me	etal Oxide	АА	You can s	ubstitute for "RH-DX04	46C	EZZ" for "VHD
								and RH-DX00	450	iezz "
							D881	VHD155119//-1	J	155119
	MISCELLANEC	200	S PAF	RTS			D882	VHD1SS119//-1	J	155119
FB602	RBLN-0037CEZZ	J	Ferr	ite Bead	b	AB	D885	VHD1SS119//-1	J	1SS119
FB603	RBLN-0037CEZZ	J	Ferr	ite Bead	ł	AB
FB701	RBLN-0037CEZZ	J	Ferri	ite Bead	ł	AB
FB702	RBLN-0037CEZZ	J	Ferri	ite Bead	ł	AB		COIL	-
FB703	RBLN-0020CEZZ	J	Ferri	ite Bead	ł	АВ	L851	VP-DF151K0000	٦	150µH
FH701	QFSHD1013CEZZ	J	Fuse	Holder		AC
	or								то	DC.
	QFSHD1009CEZZ						(851		10
FH702	QFSHD1014CEZZJFu	ise I	Holde	r		AC	(95)		,	270p 50V C
	or							VENTERINDZ/IK	J	270p 50V C

OFSHD1010CEZZ

or QFS-B4021GEZZ P101 QPLGN0241CE04 J Plug,2pin

P351 QPLGN0241CEZZ J Plug,2pin

P2001 QPLGN0541CEZZ J Plug.5pin

P2101 QPLGN0404CEZZ J Plug,4pin

OFS-B4023CEZZ J Euse 4A

QPLGN0505CEZZ J Plug,5pin

QPLGN0207CEZZ J Plug,2pin

QPLGN0441CEZZ J Plug,4pin

RMC2101RRMCU0216CEZZ J Remote Receiver

∕€ F701

P601

P701

P751

		-		,
	or
	RRLYU0031CEZZ
$2001	QSW-K0079GEZZ	J	Switch,Power	AB
S2002	QSW-K0079GEZZ	J	Switch,CH-up	AB
S2003	QSW-K0079GEZZ	J	Switch,CH-down	AB
$2004	QSW-K0079GEZZ	J	Switch,VOL-up	AB
$2005	QSW-K0079GEZZ	J	Switch,VOL-down	AB
۸	RUNTK0476CEZZ	J	Antenna Box Unit	AS

Description

PWB-B DUNTK8606WEVO CRT UNIT

TRANSISTORS

V$2$C2229O/1E	J	2SC2229(O)	AD
V$2$C22290/1E	j	2$C2229(O)	AD
V$2$C22290/1E	J	2SC2229(O)	AD
VS2SA1015Y/1E	J	2SA1015(Y)	AC
	VS2SC2229O/1E VS2SC2229O/1E VS2SC2229O/1E VS2SA1015Y/1E	V$2$C2229O/1E J V$2$C2229O/1E J V$2$C2229O/1E J V$2$A1015Y/1E J	VS2SC2229O/1E J 2SC2229(O) VS2SC2229O/1E J 2SC2229(O) VS2SC2229O/1E J 2SC2229(O) VS2SA1015Y/1E J 2SA1015(Y)

DIODES

You can substitute for "RH-DX0446CEZZ" for "VHD1SS119//-1

D881	VHD1SS119//-1	J	15$119	AB
D882	VHD1SS119//-1	J	155119	AB
D885	VHD1SS119//-1	J	155119	AB

COIL

-851	VP-DF151K0000	J	150µH	AB

CAPACITORS

851	VCKYPA1HB271K	J	270p	50V	Ceramic	AA
852	VCKYPA1HB271K	J	270p	50V	Ceramic	АА
853	VCKYPA1HB271K	J	270p	50V	Ceramic	AA
854	RC-KZ0016CEZZ	J	0.01	1.4kV	Ceramic	AC
858	VCKYPA1HB102K	J	1000	50V	Ceramic	AA
883	VCEAGA1VW336M	J	33	35V	EL.
881	VCEAGA1HW106M	J	10	50V	EL.

RESISTORS

51	VRD-RA2BE470J	J	47	1/8W	Carbon	AA
9	VRD-RA2BE470J	j	47	1/8W	Carbon	AA
7	VRD-RA2BE470J	J	47	1/8W	Carbon	AA
2	VRD-RA2BE271J	J	270	1/8W	Carbon	АА

ΑΑ

АВ

АК

R85

R86

R 89

Page 18

Re f. No.	Part No.	*	Description	Code
R860	VRD-RA2BE271J	J	270 1/8W Carbon	АА
R868	VRD-RA2BE271J	J	270 1/8W Carbon	AA
R853	VRD-RA2BE121J	J	120 1/8W Carbon	AA
R861	VRD-RA2BE121J	J	120 1/8W Carbon	AA
R869	VRD-RA2BE121J	J	120 1/8W Carbon	АА
R857	VRS-VV3AB123J	J	12k 1W Metal Oxide	AA
R865	VRS-VV3AB123J	J	12k 1W Metal Oxide	AA
R873	VRS-VV3AB123J	J	12k 1W Metal Oxide	АА
R858	VRD-RM2HD332J	J	3.3k 1/2W Carbon	AA
R866	VRD-RM2HD332J	J	3.3k 1/2W Carbon	АА
R874	VRD-RM2HD332J	J	3.3k 1/2W Carbon	АА
R881	VRD-RA2BE102J	J	1.0k 1/8W Carbon	АА
R882	VRD-RA2BE331J	J	330 1/8W Carbon	АА
R883	VRD-RA2BE561J	J	560 1/8W Carbon	AA
R884	VRD-RA2BE152J	J	1.5k 1/8W Carbon	AA

MISCELLANEOUS PARTS

P851	QPLGN0541CEZZ	J	Plug	AB
P852	QPLGN0441CEZZ	J	Plug	AB
SC851	QSOCV0829CEZZ	J	Socket,CRT	AK

MISCELLANEOUS PARTS


Ê,	QACCD3014CESA J	AC Cord	АН
	QCNW-1495PEZZ R	Connecting Cord	AE
	QCNW-1768PEZZ R	Connecting Cord	AF
	QCNW-1769PEZZ R	Connecting Cord	AG
Â	RUNTK0393CEZZ J	Antenna Adaptor	AH
	VSP0080P-H28A J	Speaker	AM

PACKING PARTS (NOT REPLACEMENT ITEM)

SPAKC5957PEZZ R	Packing Case
SPAKP0031PEZZ R	Wrapping Paper
SPAKX2527PEZZ R	Polystyrene Mat

Ref. No.	Part No.	*	Description	Code

CABINET PARTS

1	CCABA2276WEV0	R	Cabinet Comrete Ass	́уВА
1-1	-	R	Cabinet Front
1-2	GCOVA0053PEKA	R	Cover,R/C	AE
1-3	JBTN-0167PEKA	R	Button,Power,VOL-	AG
			up/down
1-4	JBTN-0168PEKA	R	Button,CH-up/down	AF
2	GCABB2238PEKA	R	Rear Cabinet	AY

SUPPLIED ACCESSORIES

QANTR0018PEZZ	R	Rod Antenna	AQ
RRMCG1124CESA	J	Infrared R-C	AW
		-BATTERY	-
TGAN-0018PEZZ	R	Guarantee Card	AD
Ti N S - 5 5 3 6 P E Z Z	R	Operation Manual
SSAKA0001PEZZ	R	Polystyrene Bag	AA

CABINET PARTS LOCATION

Page 19

Page 20

Page 21

SCHEMATIC DIAGRAM: MAIN

INDICATION OF SENSOR IC VOLTAGE (IC2001) Pin No IC2001 Logic or Voltage Levels H-Mute on L-Mute off H-TV L-Video H-Power on L-Power off 8 12 Station Detector (H-Pulse in) 13 Negative Pulse 14 AFT Voltage Input X-RAY Protector 16 10 View Timer L-LED on 19 View Timer L-LED on 20 On time L-LED on 22 Pulse (Active High) 23 Pulse (Active High) 24 Pulse (Active High) 25 Pulse (Active High) 26 Negative Pulse(H-Sync) 27 Negative Pulse(V-Sync) 28 OSD 12.08MHz в 29 OSD 12.08MHz 31 OSC Input (8MHz) 32 OSC Output (8MHz) 33 Reset (Active High) 36 Negative Pulse 37 Serial Clock Serial Clock 38 40 Caption Control (Composite Video)

Page 22

7	8	9	10	11	12

Page 23

DESCRIPTION OF SCHEMATIC DIAGRAM

NOTE:

1. The unit of resistance "ohm" is omitted (K:1000 ohms, M:1 Meg ohm).
2. All resistors are 1/8 watt, unless otherwise noted.
All capacitors are μF, unless otherwise noted P: μμF.
4. (G) indicates ±2% tolerance may be used.

VOLTAGE MEASUREMENT CONDITIONS:

1. All DC voltages are measured with VTVM connected between points indicated and chassis ground, line voltage set at 120V AC and all controls set for normal picture unless otherwise indicated.
2. All voltages measured with 1000µV B & W or Color signal.

WAVEFORM MEASUREMENT CONDI-TIONS:

1. Photographs taken on a standard gated color bar signal, the tint setting adjusted for proper color. The wave shapes at the red, green and blue cathodes of the picture tube depend on the tint, color level and picture control.
2. indicates waveform check points (See chart, waveforms are measured from point indicated to chassis ground.)

▲ AND SHADED ( ) COMPONENTS = SAFETY RELATED PARTS.

▲ MARK = X-RAY RELATED PARTS.

This circuit diagram is a standard one, printed circuits may be subject to change for product improvement without prior notice.

SHARP Service manual / Схема, сервісна інструкція Service manual & schematics