SHARP Service manual / Схема, сервісна інструкція Service manual & schematics

Page 1

SERVICE MANUAL 维修手册

SX5Z729HX5///

In the interests of user-safety (Required by safety regulations in some countries ) the set should be restored to its original condition and only parts identical to those specified should be used.

为了用户安全起见(根据一些国家的安全规程的需要),应将电视机保持于最初的状态,而且只能使用与指定物相同的部件。

CONTENTS	目录
CONTENTS Page ELECTRICAL SPECIFICATIONS IMPORTANT SERVICE NOTES ADJUSTMENT PRECAUTIONS SERVICE ADJUSTMENT TROUBLE SHOOTING TABLE CHASSIS LAYOUT DIAGRAM PRINTED WIRING BOARD ASSEMBLIES SCHEMATIC DIAGRAMS AND WAVEFORMS	目录 2 电路规格······ 3 保养维修重要注意事项······ 4 调整步骤······ 11 保养调整······ 24 • 故障检修流程图······ 33 • 机芯底盘电路布置······ 35 • 机芯底盘电路布置······ • 印刷电路板的组装件····· • 印刷电路板的组装件·····	页数 2 3 11 24 33 35 45
OVERALL BLOCK DIAGRAM	75 ● 整体电路方框图 88 ● 更换零件表	····· 75 ···· 88

WARNING

The chassis in this receiver is partially hot. Use an isolation transformer between the line cord plug and power receptacle, when servicing this chassis. To prevent electric shock, do not remove cover. No user — serviceable parts inside. Refer servicing to qualified service personnel.

告

蟼

该电视机底盘的有些部分通电。当维修本机底盘时,请在电源线插头和电源插座之间使用隔离变压器。为了防止电击的危险,不要去拆下机盖。在里面的部件, 不是使用者所能维修的,必须委托够格的维修人员来进行维修。

Page 2

ELECTRICAL SPECIFICATIONS

Power Input	AC 110~24	0V, 5	0/60 H	z (Auto)
Power Consumption				260W
Convergence	Self	Conv	eraina	System
Focus E	Si-Potential, Uni-Po	tentia	al Elec	trostatic
Sweep Deflection			N	lagnetic
Intermediate Frequencies				•
Picture IF Carrier	•••••••••••••••••••		3	8.9 MHz
Sound IF Carrier
6.5MHz			3	2.4 MHz
6.0MHz	•		3	2.9 MHz
5.5MHz	•		3	3.4 MHz
4.5MHz	•		3	4.4 MHz
Colour Sub-Carrier
PAL/NISC	·		. 34	.47 MHz
SECAM	•	34.4	94/34	.65 MHz
NTSC	•		. 35	.32 MHz
Audio Power Output Rating	12W>	< 2 + 2	6W to	otal 50W
. .		(F	RMS. 1	0% Dis)
Speaker
Size 6x13	3 cm Elliptic x 4 pcs,	4 cm	Round	1 x 2 pcs,
Maina Call Inc. and an a		12 ci	m Wo	ofer Box
voice coil impedance	•	•••	12 Ω a	t 400 Hz
			4Ωa	t 400 Hz
Agrial Innut Impadance		75.		fer Box)
Receiving Chappels	•	/51	a unb	alanced

VHE		50	*	E13
LIHE	•	E21	thru.	550
CATV	•	CZ 1	thru	7.7
			thru	2+2,
PAL-D/K SECAM-D/K		21	unu	541
VHF		D1	thru.	010
••••	•	C1	theu.	C12
LIHE		24	theu	60
••••	•	C21	thru	09, C57
PAL-I			una	C37
VHF	(IRELAND)	в	thru	1
UHF	(U.K.H.K.)	21	thru	69
NTSC-M	(0.1.1, 1.1.1, 1.			•••
VHF		2	thru	13
	(JAPAN):	1	thru	12
UHF	(US);	14	thru	69
	(JAPAN):	13	thru	62
CATV	(US):	A-6	thru	A-1.
		Α	thru	W + 29
	(JAPAN):	C13	thru	C63
Receiving Frequency			-
VHF Low	48.25 MHz	thru	161.	25 MHz
VHF High	168.25 MHz	thru	431.	25 MHz
UHF	439.25 MHz	thru	863.	25 MHz

Specifications are subject to change without prior notice.

电路规格

电源	日初切	换丿
功率消耗	26	SOM
聚焦	緊焦調	系统
焦点双电位、单电位	2.静电角	黒点
扫描偏转	·磁致	偏转
中频
图象中频载波	·· 38. 91	MHz
由来中频发油
		MHz
	32 0	MH-
		MU
5. 5AHZ		nnz Mu
	•• 34. 4	nnz
色彩剧载波
PAL/NTSC制式	34.47	MHz
SECAM制式	'34.65	MHz
NTSC制式	35.32	MHz
音响额定输出功率12W×2+26W=50W(均方根。	10%偏	姜)
		/
扬声器
	調理する	20
	1 peq 341 **	- 475
	に首初	円筋
首面阻抗	(4008)	乙則ノ
412 (	400Hz	四く
(低)	舌扬声	器)
天线输入阻抗	2非平行	钉式
接收频道
●PAL-B/G、SECAM-B/G制式
其高频VHF······· R	2~R12	\|痢道
超高新[]][]F	1~E69	痴道
方线由珈 (' ʌ T \	¥~719	油
		調消
	1.~041	1991.18
	1. 010	n dent tekn
去高殡\/fit		37列11月
ter abs der mitte		の別川
超高频UHIC ····································	21~6	频道
C2	1~05	7频道
●PAL-1制式
甚高频VHF(爱尔兰):	B∼J	频道
超高频UHF·············(英国,香港)::	21~69	频道
●NTSC-M制式
其高紉VHF(美团) ・	2~13	痲渞
	1 19	開着
- (ロギ)・(英国)・(英国)・(英国)・(	1460	の見る
	10 00	100月1月1日
「日本」、	13~04	则诅
19 53 19	b∼A-1	. 쩼 诓
A	~W+29	颁道
按收 ~~把来~~ (日本):C1	3~C63	频道

14. 戦長局刻 VHK ······· 48. 25MHz~	-161.2	5MHz

高喊甚高频 VHF ···································	-431.2	5MHz

上述规格变更之场合,恕不另行通知

Page 3

IMPORTANT SERVICE NOTES

Maintenance and repair of this receiver should be done by qualified service personnel only.

SERVICING OF HIGH VOLTAGE SYSTEM AND PICTURE TUBE

When servicing the high voltage system, remove static charge from it by connecting a 10k ohm Resistor in series with an insulated wire (such as a test probe) between picture tube dag and 2nd anode lead. (AC line cord should be disconnected from AC outlet.)

1. Picture tube in this receiver employs integral implosion protection.
2. Replace with tube of the same type number for continued safety.
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing shatterproof goggles and after discharging the high voltage completely.

X-RAY

This receiver is designed so that any X-Ray radiation is kept to an absolute minimum. Since certain malfunctions or servicing may produce potentially hazardous radiation with prolonged exposure at close range, the following precautions should be observed:

1. When repairing the circuit, be sure not to increase the high voltage to more than 34.0 kV (at beam 0 µA) for the set.
To keep the set in a normal operation, be sure to make it function on 30.5 kV±1.5 kV (at beam 1.6 mA) in the case of the set. The set has been factory — Adjusted to the above-mentioned high voltage.
- If there is a possibility that the high voltage fluctuates as a result of the repairs, never forget to check for such high voltage after the work.
Do not substitute a picture tube with unauthorized types and/or brands which may cause excess X-ray radiation.

BEFORE RETURNING THE RECEIVER

Before returning the receiver to the user, perform the following safety checks.

1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the receiver.
Inspect all protective devices such as non-metallic control knobs, insulating fishpapers, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacity networks, mechanical insulators etc.

保养维修重要注意事项

本电视机的保养只得由专门技术人员进行。

→之于高 JE 天冬約元不口 LE 年 12 白勺 1只考於 4值 1多对高压系统进行保养维修时,先于显象管管座金属部分与第二阳极引线间用绝缘线(诸如测试探针等)申接一只10KΩ的电阻器,以除去残留于高压系统中的静电。(之前,应从电源插座中拔出本机的电源引线插头。) 1.本电视机显象管为整体内爆防护设计。 2.为保证本电视机持久使用的安全,显象管的更换必须使用同型号者。 3.撒移显象管时,不得倒持其颈部上提。 4.拆装撒移显象管,必须先用布物等包护茨屏防碎玻璃,并且作完全放电处理后才能进行。

关于X射线

本电视机为无辐射的设计。因此,任何 X 射线均设计控制于最小绝对极限。然而,在发生故障或保障维修时,过长时间地暴露机芯内部加以放置之场合,便有可能在其近旁产生有害的 X 射线辐射影响。为此,务请遵循下述预防措施:

维修调整本电视机内部电路时,切勿让其高压超过34.0kV(电子束电流为0µA时)。为保证本电视机的正常工作。务必保证其高压为30.5kV±1.5kV(电子束电流为1.6mA时)的工作条件。该工作条件值在本电视机出厂前已经调试验收。 ※本电视机一旦经维修调整。可能导致上述工作高压规定值发生偏动。因此、维修调整完成。

※本电优机一旦轻维修调整,可能寻致工业工作高压观定组发生调制。因此,维修调整元毕,务请重新对其高压值进行确认检查。

3.更换显象管时,不得使用非经认可的、不同厂家、不同型号的显象管,以免产生超过规定标准的X射线辐射的危险。

维修后归还之前

在把维修后的电视机归还给用户之前,务请进行下列的安全检查。 1.检查电视机中的所有导线的绝缘包皮有无扭折破损之处,于机芯底板和其它金属部件之间有无他物夹杂。

2.检查电视机中的所有非金属质的控制旋钮、绝缘鱼鳞纸,机壳后盖、调节器和仪器隔室盖罩或屏蔽,电阻一电容隔离网以及机械部件隔离器等保护绝缘装置、器材。

Page 4

ADJUSTMENT PRECAUTIONS

This model's settings are adjusted in two different ways: through the I²C bus control and in the conventional analog manner. The adjustments via the I²C bus control include preset-only items and variable data

1) Calling the service mode by the microprocessor

① Set the switch S401 to the service mode position, and the microprocessor is put in the service mode (adjustment through the I²C bus control)
Press the CH-DOWN key on the remote controller to get ready to select the modes one by one. CROSS DOWN KEY has the same functions
⁽³⁾ Press the CH-UP key on the remote controller to get ready to select the modes in the order opposite to the above step (2). (See SERVICE MODE) CROSS LIP KEY has the same functions.
(a) Using the vor A and V keys on the remote controller, the data can be modified. CROSS LEFT and RIGHT KEY have the same functions.
Set the switch S401 to the normal mode (OFF) position, and the microprocessor is put out of the service mode

2) Factory presettings

① Set the switch S401 to the service mode position and turn on the main power switch. Initial values are automatically preset only when a new E²PROM is used (judgment with the first 4 bytes).
O The initial data are preset as listed in SERVICE MODE.
Some settings should be modified, and the others should remain as preset. For details see
Note: Once the chassis has been put together, be sure to set the switch $401 to the service mode position first and then turn on the main power switch (see 2- (1) above.) Turning on the power without initializing the E²PROM may cause a flow of excess beams.

调整时注意再加

本型号由视机由T²C总线控制与一般的模拟调节综合进行 T²C总线控制包括初始设定(预设)以及下述的变量数据项目的调整设定。

1)微处理机的保养调整状态的设定
- ①变S401开关于保养调整状态位置。微处理机即处于保养调整状态(T²C总线控制调整块杰).
- ⑦帕按遥按舞上的CH-DOWN键以顺序选择复种母袭调整状态
  - CROSS DOWN键亦具有同样功能。
- @帕按遥拉器上的CH-IID键可按与指数@相反顺序选择各种经费调整状态(同下页1 经 养调整状态之项 )
- CROSS IIP键亦具有同样功能。
- ④ 動按遥控器上的A・V 键、可变换调整数据。
- 他在并同女員內衣盤TUNIG 220090在TWNI 22009
- ⑤取消保养调整状态时、变S401开关(关闭侧)于正常状态位置即可。

2) 初始值 (预设值) 的设定

① · g S 401 开关于保养调整状态位置。打开主电源开关。即自动地设定初始值。 (仅限于R²PROM为新品时)
- (根据最前头的4位字节而判断)
②初始值设定数据送见侵养调整状态之项所列
③有些项目需要改变设定数据,而有些项目则需要保持初始设定状态,详见保养调整状杰之项所述
注意:组装电视机底盘后。必须先变S401开关于保养调整状态位置。然后再打开主电源开关。(见2-(1)之项所述)。对R²PROM不加以初始处理而打开电源开关之场合。会引起电子束电源过大发生流动。

Page 5

Page 6

(2) The contrast and brightness data for the blue background are fixed as follows. No setting is required in the service mode.

CONTRAST:	50H
BRIGHTNESS:	70H


2)关于蓝色背景的对比度和亮度数据,	出厂时设定为下记规定位置。	但是在保养调整状态

时	,	个而	场	說足

对比度:50Hz 来度:70日

(3) To go to the service mode, the data at the data at the EEPROM's addresses 00H thru 03H are read. If the data are not as given below, the EEPROM is initialized according to the table below.

Address	:	Data
00H	:	12H	02H
01H	:	36H	03H

•		0411	•	0,011
:	36H	03H		50H

85H

EEPROM items	Data
(00H)	12H
(01H)	36H
(02H)	85H
(03H)	50H
R CUT OFF	384
G CUT OFF	384
B CUT OFF	384
G DRIVE	127
B DRIVE	127
50Hz V-AMP	70
50Hz V-LINEARITY	22
50Hz S-CORRECTION	15
50Hz V-PHASE	4
50Hz H-PHASE	15
50Hz H-SIZE	34
60Hz V-AMP	70
60Hz V-LINEARITY	22
60Hz S-CORRECTION	15
60Hz V-PHASE	4
60Hz H-PHASE	20
60Hz H-SIZE	33
EW-PARABOLA	40
EW-CORNER	8
V-BIAS	4
J-CORRECTION	15
TRAPEZIUM	28
V-COMPENSATION	4
H-COMPENSATION	4
BELL FILTER	4
SECAM R-Y	6
SECAM B-Y	11
GP (GATE PULSE)	0
SUB-BRIGHT	127
SUB-COLOUR	63
SUB-TINT	63
SUB-VOL	53
AFT/SKIP	ON/OFF
C-SYSTEM	AUTO
S-SYSTEM	AUTO
NICAM	FORCED FM OFF/M1
IGR	FORCED FM OFF/ST/MAIN

(3)进入保养调整状态时,	BEPROM地址代码00H至03H的数据存储于记忆装置中。	如果该数期
不符合下记规定要求。	即按下表所示要求进行BBPROM的初始值的处理。

بال مأهيل	L /Þ 11	ı.
一一地力	これの		100. 100.

	•	MA 1/11
00H	:	12H	02H	:	85H
01H	:	36H	03H	:	50H

H	:	36H	03H	:	50H

BEPRON项目	数据
(00H)	12H
(01H)	36H
(02H)	85H
(03H)	50H
红色截止	384
绿色截止	384
蓝色截止	384
绿色激励	127
蓝色激励	127
50Hz垂直幅值	70
50Hz垂直线性度	22
50Hz同步校正	15
50Hz垂直相位	4
50Hz水平相位	15
50Hz水平尺寸	34
60Hz垂直幅值	70
60Hz垂直线性度	22
60Hz同步校正	15
60Hz垂直相位	4
60Hz水平相位	20
60Hz水平尺寸	33
BN抛物面	40
EW角部	8
垂直偏压	4
∫校正	15
梯形失真	28
垂直补偿	4
水平补偿	4
贝尔滤波器	4
SECAM制式红色亮度	6
SECAM制式蓝色亮度	11
选通脉冲	0
副亮度	127
副彩色	63
剧色调	63
音	53
目动微调/跳跃	开/关
彩色制式	自动
声音制式	自动
NICAM制式	强制调频关闭/M1
IGR制式	强制调频关闭/ST/MAIN

Page 7

EEPROM items	Data
LEVEL	3
RS	0
RTC	4
BS	▲ 1 (Note 1)

Note 1: In the bus adjustment, change the BS data of the main picture service mode from 1 to 0. The BS data should be 0 before doing cut-off and sub-brightness adjustments. It is impossible to have the data at 0 once the above adjustments have been made with 1.

(4) When the modes are switched, the last service-mode data are stored into the EEPROM.

(5) In the service mode, the user data are preset as follows.

	User data
CONTRAST	60
COLOUR	0
BRIGHTNESS	0
TINT	0
SHARPNESS	0
S-VOL	0
TREBLE	0
BASS	0
U-BASS	0
BALANCE	0
SPATIALIZER	OFF
AI-OPC	OFF
BLUE BACK	OFF
C SYSTEM	AUTO
S SYSTEM	AUTO

(6) The following key inputs call their corresponding modes.

Key input	Mode
TEXT/MIX	BELL FILTER
PIC	SECAM R-Y
CANCEL	SECAM B-Y
INDEX	GATE PULSE
SIZE	SUB BRIGHT
TIMED PAGE	SUB COLOUR
HOLD	SUB TINT
REVEAL	LEVEL
	F7

BEPROM项目	数据
强度	3
RS	0
RTC	4
BS	(注意1)

注意1:作总线线路的调整时、主荧屏保养调整状态的BS数据必须由1转为0。在作截止调整和副亮度调整之前。必须设BS数据于0。一旦用数据1来作上记调整时,则无法将该数据变为0。

(4)改变保养调整状态时,最后被设定的保养调整数据存储于EEPROM之中。

(5)在保养调整状态下。用户数据的预设位量如下:

	用户数据
对比度位量	60
彩色位置	0
売度位置	0
色调位量	0
鲜明度位置	0
音量位量	0
高音位量	0
低音位量	0
超低音位量	0
左右平衡度位量	0
超立体声位量	¥
AI-OPC位置	¥
蓝色背景位量	¥
彩色制式位量	自动
声音制式位量	自动

(6)触按以下键钮,即可呼出与其相应的保养调整状态。

键钮输入	调整状态
TEXT/MIX	贝尔滤波器
PIC(图象)	SECAM制式红色亮度
CANCEL(取消)	SECAM制式蓝色亮度
INDEX(索引)	选通脉冲
SIZE(尺寸)	副亮度
TIMED PAGE	副彩色
HOLD(保存)	副色调
REVEAL(揭示)	强度

Page 8

(7) The data in the adjust modes are adjustable in the following ranges.

Mode	Data adjustable range		Remarks
R CUT OFF	384~1023
G CUT OFF	384~1023
B CUT OFF	384~1023
G DRIVE	0~255
B DRIVE	0~255
V-AMP	0~127
V-LINEARITY	0~31	0	₩ 1
S-CORRECT	0~31	. 0	* 1
V-PHASE	0~7	0	* 1
H-PHASE	0~31	+ 5	* 1
H-SIZE	0~63	-1	¥ 1
EW-PARABOLA	0~63
V-BIAS	0~7		······································
∫-CORRECT	0~15
EW-CORNER	0~15
TRAPEZIUM	0~63
V-COMPENSATION	0~15
H-CONPENSATION	0~15
BELL FILTER	0~7
SECAM R-Y	0~15
SECAM B-Y	0~15
CHROMA GATE PULSE	0~15
SUB BRIGHT	0~255		·····
SUB COLOUR	0~115	* 2
SUB TINT	0~127
SUB-VOLUME	43~53
LEVEL	0~15
RS	0~7
RTC	0~7
BS	0~1

(7)在下表)	所示的领城内可进行调整状态	5的数据调整。
		مستحديقه بتبتد مستح متعلا المتع	I

\|		1
红色截止	384~1023
绿色截止	384~1023
蓝色截止	384~1023
绿色激励	0~255
蓝色激励	0~255
垂直幅值	0~127
垂直线性度	0~31	0 * 1
同步校正	0~31	0 * 1
垂直相位	0~7	0 * 1
水平相位	0~31	+5 ※1
水平尺寸	0~63	-1 *1
BW抛物面	0~63
垂直偏压	0~7
∫校正	0~15
EW角部	0~15
梯形失真	0~63
垂直补偿	0~15
水平补偿	0~15
贝尔滤波器	0~7
SECAM制式红色亮度	0~15
SECAM制式蓝色亮度	0~15
色度选通脉冲	0~15
副売度	0~255
副彩色	0~115	* 2
副色调	0~127
副音量	43~53
强度	0~15
RS	0~7
RTC	0~7
BS	0~1

* 1 Set the 60-Hz data according to the 50-Hz data settings. * 2 Write the service-mode data setting plus 12 in the EEPROM.

Page 9

(8) INSET PICTURE SERVICE MODE

↓

1 CONT

TINT

, R-CO

6-0

B-CO

vco

TRAP

H-PHASE 5

H-PHASE 6

Press the ENTRY key (cross center key) on the remote controller in the service mode. The inset picture service mode is called up and the adjustment items and data that appear on the screen turn from green to red. Press the key again, and the original service mode is called back. In the inset picture service mode, use the CH UP/DOWN and CROSS UP/DOWN keys to select necessary adjustment items.

CL-AI

B-GAIN

G-GAIN

R-GAIN

SS-COL

SUB-TINT

SUB-CONT

SUB-COL

SUB-BRIGHT

(8)子荧屏侵养调整状态

在保养调整状态下触按遥控器上的BNTRY键(交叉中心键)以呼出子荧屏保养调整状态接着在屏袤示器上的调整项目和调整数据的表示颜色由绿色转为红色。再次触按该键。即回到原始保养调整状态。

在子荧屏保养调整状态下。触按CH UP/DOWN键和CROSS UP/DOWN键以选择所需的调整项目。

		J.	·
UFC		▼ 射频自动增益控制	YFC	UFC
¥		Ļ	4	Ļ
VFC		亮度	₩V/WH调整	VFC
↓		Ų	•	Ļ
VP-AJ		对比度	PHP	VP调略
. ↓		Ų	•	↓ I
H-POS		彩色	YC调整	水平位量
		Ļ	4
In the direction of arrows		色调	FRM调整
in the direction of arrow;	CROSS DOWN key	↓	ł	加火方向:CH 11P線/CROSS 11P線相反方向:CH 11P線/CROSS 11P線
In the opposite direction:	CH UP key / CROSS	红色	CL调整
	OF Rey	Ļ	٨
		绿色	蓝色增益
		Ļ	4
		蓝色	绿色増益
		¥	+
		压控损荡	红色增益
		¥	ŧ
		陷波	SS彩色
		¥	↑
,		水平相位5	副色调
		Ļ	ŧ
		水平相位6	副对比度
			ł
			副彩色
			ŧ
			——→ 副亮度

х×

Page 10

(9) Here is a list of the initial data of inset picture (initialized in the same way as in (3)) and the adjustable ranges in the inset picture service mode.

(9)子荧屏的初始数据(按与(3)相同方法进行初始值的处理) 与子荧屏保养调整状态的调整范围如下表示。

	DATA
wode, EEPKOW items	INITIALIZED	ADJUSTABLE
RF AGC	0	0~63
BRIGHT	55	0~127
CONT	53	32~127
COLOUR	48	0~127
TINT	68	0~127
R-CO	60	0~127
G-CO	60	0~127
B-CO	60	0~127
vco	31	0~63
TRAP	2	0~3
H-PHASE 5	5	0~15
H-PHASE 6	8	0~15
SUB-BRIGHT	15	0~63
SUB-COL	50	0~63
SUB-CONT	30	0~63
SUB-TINT	46	0~127
SS-COL	63	0~63
R-GAIN	60	57~63
G-GAIN	60	57~63
B-GAIN	60	57~63
CL-AJ	2	0~3
ERM-AJ	1	0~3
YC-AJ	2	0~3
РНР	0	0~3
WV/WH-AJ	10	0~15
YFC	8	0~15
UFC	8	0~15
VFC	8	0~15
VP-AJ	1	0~3
H-POS	7	0~15

近승상을 2720201116日	数值
	初始值	调整范围
射频自动增益控制	0	0~63
亮度	55	0~127
对比度	53	32~127
彩色	48	0~127
色调	68	0~127
红色	60	0~127
绿色	60	0~127
蓝色	60	0~127
压控振荡	31	0~63
陷波	2	0~3
水平相位5	5	0~15
水平相位6	8	0~15
副亮度	15	0~63
副彩色	50	0~63
副对比度	30	0~63
副色调	46	0~127
SS彩色	63	0~63
红色增益	60	57~63
绿色增益	60	57~63
蓝色增益	60	57~63
CL调整	2	0~3
BRM调整	1	0~3
YC调整	2	0~3
PHP	0	0~3
WV/WH调整	10	0~15
YFC	8	0~15
UFC	8	0~15
VFC	8	0~15
VP调整	1	0~3
水平位量	7	0~15

E10

Page 11

SERVICE ADJUSTMENT

■ + B (120V) ADJUSTMENT

1. + 120V ADJUSTMENT: R733

1. Receive the "MONOSCOPE PATTERN" signal.
Call up the Video Normal mode using the remote controller.
Connect the voltmeter across D719.
A Adjust R733 so that the + 120 V line should have 120 + 0.2 V
Note: First roughly adjust this item just after turning on the set, and finely adjust it after 30 minutes of warming up at 1300 ...A Be sure to make this adjustment before adjusting the horizontal circuit vertical circuit and CBT.

2. SUB-POWER ADJUSTMENT: R747

1. Receive the "MONOSCOPE PATTERN" signal
Turn the sound volume down to zero using the remote controller
3. Adjust R747 (sub-power control) so that the voltage across C752 be 17 + 0.1 V
Note: First roughly adjust this item just after turning on the set, and finely adjust it after 30 minutes of warming up at 1300 "A.

PIE/AFT/AGC ADUISTMENT

1. TUNER IFT (1) ADJUSTMENT: TU5201 (preset)

1. Get the tuner ready to receive the E-9CH signal. but with no signal input. Adjust the PLL data. 2. Connect the sweep generator's output cable to
the tuner antenna. (RF sweep) 3. Adjust the sweep generator's output level to 80
dB_µV. 4 Connect the response lead fuse a lowimpedance probe with wave detector: see Fig. 1) to the tuner's IF output terminal (This terminal must have the probe alone
5. Set the RF AGC voltage to 0-6 V with no contact
Adjust the tuner IF coil to obtain the waveform as shown in Fig. 2.
Note: Be sure to keep the tuner cover in position during this adjustment.

ЕОСН

2. TUNER IFT (2) ADJUSTMENT: TU5202 (preset) Take the same procedure as in the above item

保养调整

1 1-1201/0513月218 ・ 12733
1. 接收"单象管图案"信号。
2 通过遥控器呼出标准图象状态
3.接电压计于D719两端。
▲ 调节R733 伸+120V线路的由压值达至120V±0 2V的规定要求。
注意:作此项调整时,必须先打开电视机的电源开关后立刻进行粗调,然后用1300 µ A的由子車由流預执局會管30分钟。此项调整必须在水平同步电路、垂直同步电路及CRT的调整之前进行。
9 取1曲初町 64 100 北大・127 4 7
- 1 接收"单参管图案"信号。
- 9 通过遥控舆论在最子0位景
- 3. 调节R747(副电源控制)。使(?752两端的电压值达至17±0.1V的规定要求。
- 注意:作此项调整时,必须先打开电视机的电源开关后立刻进行粗调,然后用1300 µ A的电子束电流预热显象管30分钟。

■ PIF/AFT/AGC 的调略

1. 调谐器 IFT(1)的调整: TU5201(预设) 1.于无信号输入的接收状态下。使调谐器处于接收B-9频道信号之状态。调节PLL数据 2.接扫描振荡器输出线圈干训涉员干线接续。 (射频扫描)。 3. 调扫描提落器输出由平台8048 u V
4.接响应引线(带有检波器的低阳抗扬射·周图1)于调谐器中频输出端。(只接探针于调
谐器中频输出端). 5.设射翔自动增益控制RF AGC的电压值于0至 6V间的与波形不接触之位号
6. 耳將週谍器中都线圈所得放形调至图2所示的规定要求
注意:作此项调整时。必须盖上调谐器盒盖而进行。

2. 调谐器TFT(2)的调整:TU5202(预设)

按与上记相同步骤进行调整。

Page 12

PIF/AFT/AGC ADJUSTMENT

3. VCO FREE-RUN ADJUSTMENT: T2203 (on RiFU-0040CEZZ, preset)

1. Employ the zero-beat method for this adjustment
Maintain 0.V at pip (6) of IC2201 (IE AGC)
3. Apply the following signal to pin (11) of IC2201 with a 0.01-vE canacitor in between • Frequency: 38.9 MHz (CW) ± 5 kHz
- 70 + 5 dB ....

4. Connect the oscilloscope to pin (15) of IC2201 Adjust T2203 to ensure zero heat Note: Before starting this adjustment, warm up (C2001 for at least 2 minutes.

4. S-DET ADJUSTMENT (on RiFU-0040CEZZ, preset)

1. Feed the following signal to the IN of CF2201 (pin (9) of IC2201) with a 0.01-μF capacitor in between Frequency: 6.0 MHz (CW) ± 1 kHz
- + 90 + 5 dBuV
Connect the oscilloscope (DC range) and the digital voltmeter to pin (19) of IC2201. Take the steps
- a) Maintain 0 V at pin (17) of IC2201. Take the then voltmeter reading h) Allow nin (17) to have its original voltage.
- c) Adjust T2202 to obtain the voltage measured in Step a) (about 4.5 V). Accuracy: ±0.1 V

5. AFT ADJUSTMENT (1): T2204 (on RIFU-0040CF77)

1. Receive the E-12CH (PAL colour bar) signal. If this signal is not available, any signal above the E-5CH band is acceptable.
- Field strength: 55-80 dB ...................................
- Make sure the frequency is almost the same as that of the received channel (± 30 kHz).
Using the channel setting control, make a frequency of 224.25 MHz appear on the screen. (AFT off) (If any other channel than E-12CH is received, make its frequency on the screen.)
3. Adjust T2204 so that the DC voltage at the AFT OUT terminal (pin (1) of SH) of the IF unit be 45+01V

6 AFT ADJUSTMENT (2) T5801

1. Do the same as Step 1 in the preceding item
Do the same as Step 1 in the preceding item Do the same as Step 2 in the preceding item
Adjust T5801 so that the DC voltage at the AFT OUT terminal (pin (1)) of IC5802 be 5.5 ± 0.1 V
4. Do the same as Step 4 in the preceding item
4. Do the same as step 4 in the preceding item. Note: Make this adjustment with the hus data at 31/63. Re sure that the on-screen display is validw. The data can be transferred only when the AFT on/off of the inset picture is interlocked with that of the main picture and when the inset picture's channel is not brought up or down

3. 压控振荡器VCO自激的调整:T2203(于RIFU-0040CEZZ、预设)
1.此项调整以零拍法进行。
2.设IC2201(中颜自动增益控制)的销(6)为0V状态。
3. 通过串接一只0.01 µ F的电容器,对IC2201的销(11)加以下述波形信号。 ● 網本 : 38 9MHz(CW) + 5kHz
●由平・70+5dBu W
4. 接示波器于IC2201的销(15)。调节T2203。使其输出波形达至无差拍状态。
注意:作此项调整之前,必须对IC2001预热2分钟以上
4 信号检波的调整(平RIFU-0040CRZZ, 预设)
1. 通过串接一只0.01 µ F的电容器。从CF2201的输入端(IC2201的销(9))输入下述波形信号。 ● 期本・ 6 0MH₂ (CW) + 1kH₂ ● 电平: 90 ± 5dB µ V
2.接示波器(直流测定范围)和数值电压计于IC2201的销(19)。按下述要求调查T2202 a)设IC2201的销(17)为0V状态,测定电压值。 , h)将销(17)间至廣始状态 c)调节T2202, 使a)项所测电压值达至4.5V左右的规定要求。
- 糖度:±0.1V
5. 自动撤调AFT(1)的调整:T2204(于RIFU-0040CEZZ)。
1.接收B-12频道(PAL制式彩条)信号。无B-12频道信号输入时。可用B-5频道以上的频道信号代数
- 场唱度:55~80dB µ V
必须正确地调节接收频道的频率(±30kHz)。
2. 通过频道设定开关、调荧屏上表示出的频率数值为224. 25MHz. (AFT处于关闭状态)。 (接收除了B-12频道以外的频道信号时,必须采用与其相应的知塞)
3. 调节T2204. 使中频装置的自动撤调输出端(SH的销(1))处的直流电压值达至4.5±0.1V 的报空真少
各自动被调ART(2)的调整。15201
1.按与5-1相同步骤进行。
9 按与5-9相同步转进行
3. 调节T5801. 使IC5802的自动微调输出端(销(1)) 处的直流电压值达至5.5±0.1V的规定西安
4.按与5--4相同步骤进行
注意。作此项调整时,必须设压控提落器的总线控制数据于31/63位置。并且检查在屏表示文字的颜色悬否变为黄色
- 子荧屏的自动微调开/关操作联锁于主荧屏。但是不作子荧屏的规道上称/下移动作。就不能传达数据于主荧屏。请加以注意。

Page 13

PIF/AFT/AGC ADJUSTMENT

7 REAGC CUT-IN ADJUSTMENT (1): R5214

1 Receive the "PAL COLOUR BAR" signal • Field strength: 57 + 1 dB_WV (75 obms open) 2. Connect the oscilloscope to TP5201 (P5201), as
shown in Fig 3
About 6.5 V 3 Turn R5214 to have the highest voltage
4. Turn R5214 slowly in the opposite direction until the voltage goes down 0.1 V below the highest
5 Adjust the signal level to 63-67 dB₄V and make
6. Now adjust the signal level to 90-95 dBuV and make sure there is no chrominance modulation heat
Note: If a 50-ohm field strength meter is used without a 50/75 impedance converter set the field strength to 55 ± 1 dB_#V. Pay attention to a loss that would be caused with the converter.

8. RF AGC CUT-IN ADJUSTMENT (2)

(bus adjustment, inset picture service mode)

1. Do the same as Step 1 in the preceding item
Connect the oscilloscope to TP202 (P5202), as shown in Fig. 3.
Adjust the "RFAGC" bus data until the voltage goes up to the highest level (maximum at 0/63).
4. Adjust the "RF AGC" bus data until the voltage goes down to 0.2 V below the highest level.
5 Do the same as Step 5 in the preceding item. 6. Do the same as Step 5 in the preceding item.

9. VIDEO DETECTION LEVEL ADJUSTMENT: 85218

Receive the "B/G SYSTEM PAL COLOUR BAR" signal (100% white colour bar) Set the S system to B/G
2. Adjust R5218 so that the video output at the AV OUT terminal be 1.0 ± 0.05 Vp-p with a 75-phm termination

Note: In using the "I SYSTEM PAL COLOUR BAR" signal for this adjustment, set the S system to L

■ PIF/AFT/AGC的调整

7. 射频自动增益控制RF AGC插入的调整(1): R5214。 1.接收"PAL制式彩条"信号。 ●场强度・57+1dBuV(機接750曲加) 2. 按图3所示要求接示波器于TP5201(P5201)。 ●偏乐器・約6.5V 3.旋转R5214、使所闌电压读数达至最大。 4. 按与步骤3. 相反方向逐渐旋转R5214, 将电压读数调至最大值-0.1V之程度。
5. 调信号强度为63~67dBuV 确认无端声出现。
6. 再调信号强度为90~95dBuV 确认无负度肩長運動並拉山理注意:加果使用不带50/75阻抗转换器的500 系统场强度计。该场强度必须定为55± 1dBµV。另外,使用转换器时,应考虑

由转换器带车的阻抗损失

8. 射频自动增益控制RF AGC插入的调整(2)。 (总线控制,子荧屏保养调整状态) 1.按与7-1相同步骤进行 2 培图3所示要求接示波器于TP202(P5202)。 3. 调节"RF AGC"的总线数据。直至电压值达至最大程度为止(0/63为最小)。 4.将"RF AGC"的总线数据调至最大值-0.2V之程度。 5 按与7-5相同步骤进行 6. 按与7-6相同步骤进行。
9.视频检波电平的调整: R5218
1. 接收"B/G制式PAL彩条" 信号(100% 白色信号)。设S-制式于B/G位置。
2. 调带R5218. 体声象输出端外的视频输出强度达至1.0±0.05Vp-p的规定要求(于75Ω接线端).
注意:用"I制式PAL彩条"信号来进行此项调整时。应设S制式于I位量。

Page 14

3. CONTRAST ADJUSTMENT: IC5802 (IF, V, C, J IC) (bus adjustment, inset picture service mode)

Select an inset picture channel, and receive the "PAL COLOUR BAR" signal (100% white signal). Set the S system to B/G.
Connect the oscilloscope to TP4802 in the P-in-P unit. (emitter of Q4410)
3. Adjust the contrast data until the difference between the 100% white level and the black level becomes 0.7 Vp-p. Control level: 0.7 + 0.04 Vp-n

Fia. 7.

图7

C14

Page 15

SOUND ADJUSTMENT

1. RF SUB-SOUND ADJUSTMENT: R2257 (on RIFU-0040CEZZ, preset)
1. Receive the "PAL COLOUR BAR" signal. • Signal: 400 Hz, 100% modulation
Connect the oscilloscope to the Audio Out (L or R) terminal. (Terminate with a 10-kohm impedance.) Adjust R2257 so that the 400-Hz sine wave be of 1.76 Vp-p. Adjustment error: 1.76 ± 0.04/ – 0.06 Vp-p
2. SUB-SOUND ADJUSTMENT (bus adjustment)
Receive the "PAL COLOUR BAR" signal. Signal: 400 Hz, 100% modulation (50 kHz dev.)
2. Turn up the volume control to maximum.
Connect the VIVM's probes to the SI connector (pin (1): L-ch, pin (2); Ground, pin (3): R-ch). Adjust the sub-sound data so that the VTVM should read 8.5 Vrms (for the left channel). Adjust the sub-sound data so that the VTVM should read 8.5 Vrms (for the left channel).
Notes:
Spatializer off
In the S-Normal mode
S-VOL control at MAX position
3. NOISE MUTE CHECKING
1. Receive the "PAL COLOUR BAR" signal.
Turn up the volume control to maximum and make sure the sound is heard from the speakers. Then put the unit in the no-signal state.
3. Be sure that the sound mute is effective.
4. Finally turn down the volume control to minimum.

SYNC DETECTION ADJUSTMENT

1. SYNC DETECTION FREQUENCY ADJUSTMENT: R5656

1. Put the unit in the A/V mode with no signal input.
Connect the frequency counter to TP5601 (on the IF/AV unit PWB). (Use a probe with small input capacitance: 10:1 or so of the oscilloscope)
(Use a probe with small input capacitance: 10:1 or so of the oscilloscope) Adjust R5656 so that the frequency counter should read 15.65 ± 0.05 kHz.
Warm up the unit for 20 minutes or longer before starting this adjustment.

SIF (NICAM) ADJUSTMENT

1. CARRIER DETECTION COIL: T5303

1. Receive the "PAL COLOUR BAR" signal.
Connect the oscilloscope to TP5303. Range: Horizontal; 20 msec/div.
- Vertical; 20 mV/div. (10:1 probe used)
Adjust T5303 until the video signal component of the detection output waveform becomes minimum.

■ 声音制式的调整

1.	射频副声音的调整:R2257(于RIFU-0040CBZZ, 預设)。
	1. 接收 "PAL制式彩条" 信号。
	●信号成分:400Hz,100%调制
	2. 接示波器于音频输出端(左或右)。(端接10kΩ电阻)。
	3. 调节R2257, 使400Hz正弦波幅值达至1.76Vp-p的规定要求。
	●调整误差:1.76±0.04/-0.06Vp-p
2.	副声音的调整(总线控制)
	1. 接收"PAL制式彩条"信号。
	●信号成分:400Hz,100%调制(50kHz偏转)。
	2. 设音量控制于最大位置。
	3.接电子管电压计VTVM的探针于SI接线器(铕(1):左声道,铕(2):接地,铕(3):右
	声道)。
	4.调节副声道数据,使电子管电压计所测读数达至8.5Vrms(于左声道)的规定要求。
	●调整误差(于左声道):8.5±0.1Vrms
	注意:
	●超立体声控制:OFF位置
	●标准声音状态位置
_	●音量:最大位置
3.	消音功能的检查
	1.接收"PAL制式彩条"信号。
	2.设音量控制于最大位置,接着检查扬声器的声音输出,然后,设电视机于无信号接收划
	态。
	3.此时,检查消音功能是否动作。
	4.最后,设音量控制于最小位置。
	同步检波的调整
\|	間-步ぬかって調査を B5656
••	1 沿由如机干击争制式的干值导体的作为

接計数式頻率计于TP5601(中頻/声象装置的印刷电路板上)。 (必须使用输入容量小的探针:对示波器为10:1为宜。)

3.调节R5656,使计数式频率计所测读数达至15.65±0.05kHz的规定要求。
*作此项调整之前,应先预热电视机20分钟以上。

SIF(NICAM制式)的调整

載放检放线圈: T5303 1.接收 "PAL制式彩条"信号。 2.接示波器于TP5303。 ● 测示范围:水平;20毫秒/段垂直;20mV/段(使用10:1探针时) 3.调节T5303,使检波输出波形的视频信号成分达至最小。

Page 16

■ SIF (IGR) ADJUSTMENT (29HX5 ONLY)

1. S-DET: T5301 (5 5M) T5302 (5 74M)

Receive the colour bar video signal
2. Make the following audio settings
- Make the following audio settings. Two-sound mode (Push the M1 or M2 switch )
- RF output: RUUB"
Connect the VTVMs to TP5301 and TP5302 with a 1-#F capacitor each in between Adjust T5301 and T5302 so that he VTVMs read the highest levels.

2. AUDIO LEVEL: R5311

Under the same signal conditions as above, do the following,

1. Set the unit to the bilingual mode (MAIN or MAIN + SUB) Note: Make cure that "MAIN" or "MAIN + SUB" appears on the screen. Terminate the AUDIO OUT (L) terminal with a 10-kohm impedance. Adjust the audio level control
(R5311) so that the synchroscope read 1.32 Vn-n + 0.04 Vn-n

3. SEPARATION: R5310

Under the same signal conditions as above, do the following. Set the signal generator to STEREO mode (Push the L or R switch). Turn off the MONO1 (L) audio signal

Note: Press the S switch and make sure the meter reads 15-kHz deviation. 1 Set the unit to STEREO mode

Note: Make sure that "STEREO" appears on the screen.
2. Terminate the AUDIO OUT (1) terminal with a 10-kohm and adjust the separation control (85310) so that the 400-Hz waveform on the synchroscope screen be minimum. Note: This adjustment requires a specific IGR signal generator

4. TEXT LEVEL: R1815

1 Possive the TEVT signal
Connect the oscilloscope to pin (7) of the TX connector. Range: 20mV/div. (with a 10:1 probe.)

Adjust R1R15 so that the TEXT signal level be 0.6 ± 0.01 Vp-p.

■中音频SIF(IGR)的调整(只限于型号29HX5)

1. 信号检波: T5301(5.5M)。 T5302(5.74M)

1 接收彩条如知信号
2.按下记要求进行音棚设定。
"M1", "M2": 400Hz, 30kHz偏转。双音频设定状态。 (帧按M1或M2开关)
射頻輸出・80-4B u
3. 通过串接一只1µ7的电容器。接电子管电压表于TP5301和TP5302。
4.调节T5301和T5302。使电子管电压表所测的读数达至最大程度。
9 安朝由平・P5911
- 在与上记相同的信号条件下进行下记步骤。
- 1 份申知机士奥神运享份资格奖(于建享MAIN略字进享MAIN+创建享SUB)
- 注意:检查确认在荧屏上是否出现"MAIN"或MAIN+SUB"文字。
2 通过10kQ阻抗端接在新输出端(左侧) 调节音频电平控制(R5311),使同步示波器所测的读数达至1,32Vp-p±0,04Vp-p的规定要求.
3. 音频信号分离: R5310
在与上记相同的信号条件下进行下记步骤。
设信号发生器于STEREO(立体声)状态(触按L(左)或R(右)开关)。
切断MONO1(L)音频信号。
注意: 帕按S开关以检查所测读数是否为15kHz值转。
1.设电视机于STEREO(立体声)状态。
注意·检查确认在按展上最否出现"STRRRO"的文字。
2. 通过10kΩ阻抗。端接音频输出端(左侧)。调节分离控制(R5310) 使同步示波器上显示出的400Hz波形达至最小。法查·作业而调整时重要性政的TCD自导会出现
4 文字表示信号由平・P1815 1.接收TRXT(文字表示)信号。 2. 接示波器于TX接线器的销(7)。 ●潤示茲图:20mV/段(使用10:1的探针) 3.调节R1815. 使TEXT (文字表示) 信号电平达至 0 6+0 01Vn-n的期空要求

Page 17

■ INSET PICTURE OUTPUT LEVEL ADJUSTMENT

1. SUB-CONTRAST ADJUSTMENT: IC4805 (RGB output) (bus adjustment, inset picture service mode) 1. Bereive the "PAL COLOUR BAR" sincel Set the S. Main picture's 100% white

1. Receive the "PAL COLOUR BAR" signal. Set the S system to B/G.
- Inset picture size: 1/4
Display position: Lower right
Connect the oscilloscope to TP851 (pin (3) of KY) in the CRT unit.
Adjust the sub-contrast data of the inset picture RGB output IC so that the 100% white level of the main picture and that of the inset picture be at the same level.

2. SUB-BRIGHTNESS ADJUSTMENT: IC805 (RGB output) (inset picture service mode)

Receive the "MONOSCOPE PATTERN" signal for both the main and inset pictures. Adjust the subbrightness data so that the black portions of both pictures be at the same level. Note: Make sure the main picture's sub-brightness has been perfectly adjusted.

3. WHITE BALANCE ADJUSTMENT (inset picture service mode)

1. Receive the "MONOSCOPE PATTERN" signal.
Check the difference in white balance between the main and inset pictures. If too much difference, readjust the R, G and B gains.
3. The initial gain is 60 for all the R, G and B colours. Adjust any two of the colours to a gain of 60 ± 3.

PURITY ADJUSTMENT

Receive the green only signal or "MONOSCOPE PATTEN" signal. Adjust the contrast control to have a beam current of 1.3 mA. Decause the CRT enough with the degaussing
Degauss the CRT enough with the degaussing coil. Keep the purity magnet in the zero magnetic
Keep the purity magnet in the zero magnetic field in advance. Roughly adjust the convergence.
Observe the points "a" and "b", as shown in Fig. A, through a microscope. Adjust the landing to the rank "A" requirements.
Adjust the raster rotation to 0 eastward. Tighten up the deflection coil screws.
Tighten up the deflection coil screws. Tightening torque: 108 N + 20 N
(11 ± 2 kgf) 7. While observing the CRT screen corners, apply
the magnet sheet to have the landing at rank "C". Note: Before starting this adjustment, warm up
Note: Before starting this adjustment, warm up the unit for 30 minutes or longer at a beam current of over 1300 µA (SX-68E9).

E17

子荧屏输出电平的调整

副对比度的调整:IC4805(红绿蓝RGB三色信号输出)(总线控制,子荧屏保养调整状态)。 1.接收 "PAL制式彩条"信号。设S制式于 B/G位置。 ●子荧屏尺寸:1/4 ●表示位置:右下 2.接示波器于CRT装置的TP851(KY的销(3))。调节子荧屏RGB输出集成块的副对比度数据, 使主荧屏与子荧屏的100%白色信号电平达至相同程度。
副亮度的调整:IC805(红绿蓝RGB三色信号输出),(子炭屏保养调整状态)。主荧屏和子荧屏均接收"单象管图案"信号。调节副亮度数据,使主和子荧屏双方的黑色信号电平达至相同程度。注意:此项调整必须于主荧屏的副亮度调整完毕后进行。

3. 白色平衡的调整(子荧屏保养调整状态)。

1.接收"单象管图案"信号。
2. 检查主荧屏与子荧屏间的白色平衡之差,若该差极大,即重调红绿蓝三色的增益。
3. 红绿蓝三色的初始值均为60, 所以, 将其中之两色调至60±3的增益。

■ 色彩纯度的调整

1. 接收损负单负信号或"单单管图案"信号然后通过对比度控制调电子束电流干1.3mA 2.通过消费线圈对CRT作完全消费处理 3.调整前,先调整色彩烛度控制磁铁。伸其带场磁势为0、然后。再对色彩纯度进行粗调。 4.用放大显示镰观察图A所示的a点和b点调节纯度磁铁。伸其着屏点位冒达至"A"级的提定要求。 5.保持荧屏面朝东方。调其光栅转角为()。 6.旋紧偏转线圈的紧闭螺丝。 ● 階間力街・108N + 20N (11kgf ± 2kgf) 7. 检查CRT角部。用一磁铁片加以校正。使其著展占法至"0"级以上的规定要求。注意:作此项调整之前。先用大于1300 μ Α (刑号SI-68R9)的由子東由流預热CRT30 分钟以上。

Page 18

CONVERGENCE ADJUSTMENT

(To be done after the purity adjustment)

1. Receive the "CROSSHATCH PATTERN" signal.

2. Using the remote controller, call the Normal mode.

STATIC CONVERGENCE

Turn the 4-pole magnet to a proper opening angle in order to superimpose the blue and red colours. Turn the 6-pole magnet to a proper opening
I urn the 6-pole magnet to a proper opening angle in order to superimpose the green colour over the blue and red ones.

DYNAMIC CONVERGENCE

Adjust the convergence on the fringes of the screen in the following steps.
- a) Fig. a: Drive the wedge at point "a" and swing the deflection coil upward.
b) Fig. b: Drive the wedges at points "b" and "c" and swing the deflection coil downward.
c) Fig. c: Drive the "c" wedge deeper and swing the deflection coil rightward.
d) Fig. d: Drive the "d" wedge deeper and swing the deflection coil leftward.
Fix all the wedges on the CRT and apply glass tape over them.
Apply lacquer to the deflection yoke lock screw, magnet unit (purity, 4-pole and 6-pole magnets) and magnet unit lock screw.

■ 画面聚焦度的调整

(此项调整必须于色彩烛度磁铁调整完毕后进行)

1.接收"棋盘格测试图案"信号。 2.通过遥控器设电视机于标准状态。

静聚焦度的调整

調节4极聚焦磁铁的开角与转角,使蓝色线条与红色线条重叠。调节6极聚焦磁铁的开角与转角,使绿色线条与蓝、红色重叠线条重叠。

动聚焦度的调整

1. 按下述要求调节荧屏周边的聚焦度。
a)图a:插调整楔于"a",向上摆动偏转线图加以调节。
b) 图b: 插调整楔于 "b"和 "c",向下摆动偏转线圈加以调节。
c) 图c:深插调整楔 "c",向右摄动偏转线窗加以调节。
d) 图d:深插调整楔"d",向左摆动偏转线图加以调节。
2.贴三支调整楔于显象管CRT上,用玻璃胶带固定之。
3.加封固胶于偏转线圈的固定螺丝、磁铁装置 (色彩纯度调节磁铁、4极与6极聚焦磁铁) 以及磁铁装置的固定螺丝、封固之。

Page 19

6. 调中对比度及先度控制,便电子束电就这至200 µ A,检查背景的色彩显示。此时,如果色温并非为12300° K,则必须返回至前项的第1项重新进行调整。注意:作此项调整之前,必须先用1300 µ A的电子束电流预热CRT30分钟以上。

Page 20

CRT Cut-Off, Background and Sub-Contrast Adjustments

3. SUB-CONTRAST ADJUSTMENTS

Adjusting Point
Sub-Contrast: R1009
1. Receive the "MONOSCOPE PATTERN" signal.
2. Using the remote controller, call the Video Normal mode.
Connect the beam ammeter between TP601 and TP602.
Ammeter's full-scale: 3 mA range
Ammeter's positive (+) lead: TP602
Ammeter's negative (-) lead: TP601
Adjust R1009 (sub-contrast control) so that the beam current be1.6mA.
Note: Before starting this adjustment, warm up the unit for 30 minutes or longer at a beam current of 1300 µA .

HORIZONTAL AND VERTICAL CIRCUIT ADJUSTMENT

1. SERVICE MODE DATA ADJUSTMENT

For the items 1 thru 6 below, use	the remote controller in the service mode.
1. V-HEIGHT 50:	Adjust the overscan to 8% (E-5).
2. V-LINEARITY 50:	Adjust to get the best linearity.
3. V-S-CORRECTION 50:	Preset (readjust if the linearity is poor)
V-SHIFT 50 (V-CENTER):	Align the screen center with the CRT's geometrical center (F-5)
5. H-SHIFT 50 (H-CENTER):	Align the screen center with the CRT's geometrical center (E-5)
6. H-WIDTH 50 (H-SIZE):	Adjust the overscan to 8% (E-5).
7. EW-PARABOLA (SIDE-PIN):	Adjust so that the second vertical lines from the left and right ends o the crosshatch pattern be straight (F-2)
8. V-BIAS:	Preset
9. V-S-CORRECTION:	Preset
10. EW-CORNER (SUB-SIDEPIN):	Preset (readjust if the picture quality at the corners is degraded)
11.TRAPEZIUM:	Preset
12. V-COMPENSATION:	Preset
13. H-COMPENSATION:	Preset
14. Others:	For the V-HEIGHT 60, V-LINEARITY 60, V-S-CORRECTION 60, V-SHIFT 60, H-SHIFT 60 and H-WIDTH 60 adjustments, their corrected data are automatically entered when the corresponding 50-Hz mode adjustments are made.

2. FOCUS ADJUSTMENT

1. Receive the "MONOSCOPE PATTERN" signal.
Using the remote controller, call the Video Normal mode

Adjust the focus control so that the center of screen is good focus.

CRT截止、蓝色背景以及副对比度的调整

3.副对比度的调整
调整点
■副对比度:R1009
1.接收"单象管图案"信号。
2.通过遥控器选择标准图象状态。
3. 接电子束安培计于TP601与TP602之间。
●安培计测示范围:3mA
●TP602于安培计正(+)例
●TP601于安培计负(一)侧
4.调节R1009(副对比度控制),使电子束安培计所测读数达至1.6mA的规定要求。
注意:作此项调整之前,必须用大于1300 µ A的电子束电流预热CRT30分钟以上。

■水平同步电路及垂直同步电路的调整

1.保养调整状态、数据的调整
本节下述的1~6项目数据的调整	,由遥控器进行保养调整状态的调整。
1.垂直高度50:	进行调整,使过扫描达至8%。(B-5)
2. 垂直线性度50:	进行调整,使垂直线性度达至最佳状态。
3. 垂直同步校正50:	预设(线性度不良时,重新调整之。)
4.垂直偏移50(垂直中心):	通过CRT的几何中心与荧屏中心对齐进行调整。(B-5)
5.水平偏移50(水平中心):	通过CRT的几何中心与荧屏中心对齐进行调整。(B-5)
6.水平幅度50(水平尺寸):	进行调整,使过扫描达至8%。(18-5)
7.B/W抛物面(两侧枕形畸变):	通过拉直棋盘格测试图案左右两端的第二条垂直线条进行调
	整。(B-2)
8. 垂直偏转:	预设
9.垂直同步校正:	预设
10. K/W角部(副两侧枕形畸变):	预设(若有显著地不正常之处,便进行调整)
11. 梯形失真:	预设
12. 垂直补偿:	预设
13.水平补偿:	预设
14. 其它:	关于垂直高度60、垂直线性度60、垂直同步校正60、垂直偏
	移60、水平偏移60以及水平幅度60之项目,只作50Hz的调
	整,便可自动地输入已校正好的数据。
2. 焦点的调整

1.接收"单急管图案"信号。
2. 通过遥控器选择标准图象状态。
3. 调节焦点控制, 使荧屏中央部的字符表示达至最清晰之程度。

Page 21

■ IMAGE POSITION ADJUSTMENT OF INSET PICTURE

1. SUB-H-SHIFT (50)

The data has been preset. If the shifting is not specified, adjust the data so that the overscans at both sides of the inset picture be the same.

2. SUB-H-SHIFT (60)

The data has been preset. When the Sub-H-Shift (5) data has been adjusted, the correction data is automatically entered for the Sub-H-Shift (60).

3. CHANNEL SIGN POSITION ADJUSTMENT: T1001 (in inset picture)

1. Make the P-in-P inset picture in the 1/4 size. Receive the "MONOSCOPE PATTERN" signal.
Adjust T1001 so that the tip of the channel number "5" be in exact contact with the pattern's circle.
Adjustment error: ±3 mm

4. INSET PICTURE DISPLAY POSITION ADJUSTMENT

(bus adjustment, inset picture service mode)

1. Receive the "MONOSCOPE PATTERN" signal.

Adjust the H-POS and VP-AJ data as shown below. (inset picture size: 1/16)

Clearances A and B to be almost the same Clearances C and D to be almost the same (Inset picture size: 1/16)

■子茨屏内的图象位置调整

1. 副水平偏移(50)
1.数据已被预设。

偏移不符规定要求时,调节数据,使子荧屏内左右两端的过扫描一致。

2.副水平偏移(60)

1.数据已被预设。

·调节副水平偏移(50)的数据时。即自动地输入校正数据信号于副水平偏移(60)中。

3.频道信号表示位置的调整:T1001(子荧屏) 1.在主费展上呼出1/4尺寸的子费展接收

1.在主荧屏上呼出1/4尺寸的子荧屏,接收 "单象管图案"信号。 2.调节T1001,直至频道表示数字"5"的左下边缘接触至单象管图案的圆周为止。 ●调整误差:±3mm

子荧屏的表示位置调整 (总线控制、子荧屏保养调整状态)。

技收"单象管图案"信号。调节水平位置数据和垂直位置数据,以获得下图所示的图案。(于费屏尺寸:1/16)

A与B几乎相同 C与D几乎相同 (子荧屏尺寸:1/16)

Page 22

PAL CHROMA ADJUSTMENT

1. SUB-COLOUR (1) ADJUSTMENT

(I²C bus adjustment, main picture)

1. Receive the "PAL COLOUR BAR" signal.
Receive the remote controller, call the Video Normal mode.
3. Connect the oscilloscope to TP852 (RED cathode). (Use a 10:1 probe.) • Range: 2 V/div
Sweep time: 20 usec/div
Using the remote controller, call the sub-colour adjustment mode. Adjust the sub-colour data so that the 75% white and red portions of the PAL colour bar be at the same level. See Fig. 9.
Clear the adjustment mode. (Now the 100% white and red portions will be at the same level.)

2. SUB-COLOUR (2) ADJUSTMENT

(I²C bus adjustment, inset picture service mode) Call the inset picture sub-colour adjustment mode. Taking the same steps as in the SUB-COLOUR (1) ADJUSTMENT, bring the 75% white and red portions of the PAL colour bar in the inset picture to the same level. (This level does not change even by clearing the

adjustment mode.)

NTSC CHROMA ADJUSTMENT

1. SUB-TINT (1) ADJUSTMENT

(main picture, I²C bus adjustment, inset picture)

1. Call the sub-tint adjustment mode. Receive the "NTSC COLOUR BAR" signal.
2. Connect the oscilloscope to TP802 (B-Y). Range: 20 mV/div. (AC)
Sweep time: 20 µsec/div. (Use a 10; 1 probe.)
Adjust the sub-tint (1) data to obtain the waveform as shown in Fla . 10.
4. Clear the adjustment mode.

2. SUB-TINT (2) ADJUSTMENT

(inset picture service mode)

Receive the "NTSC COLOUR BAR" signal. Call the sub-tint adjustment mode.
Connect the oscilloscope to pin (4) of KY in the CRT unit. (Keep the main picture out of the A/V signal.)
3. Adjust the sub-tint (2) data to obtain the waveform as shown in Fig. 11.
4. Clear the adjustment mode.

75% white and red to be

Fig. 9.

Fig. 10.

Fia. 11.

3. 接示波器于TP852(红色阴极)。(使用10: 1的探针) ● 测示范围:2V/段 ● 扫频时间:20微秒/段 4. 通过遥控器选择副彩色调整状态。然后,调节副彩色数据,使PAL制式彩条信号中的 75%白色信号电平与红色信号电平一致。见图9. 5. 取消此项调整状态的设定。(由此,100% 白色信号电平与红色信号电平成为相同程度)。 2. 副彩色(2)的调整

副彩色(2)的调整 (I²C总线控制,子荧屏保养调整状态) 选择子荧屏用的副彩色调整状态后,按与 "副彩色(1)的调整"相同步骤进行调整, 使子荧屏的PAL制式彩条信号内的75%白色信号电平与红色信号电平一致。 (取消此项调整状态的设定时,该电平亦不会有变动)

使白色信号与红色信号的电平值相同

218

NTSC制式色度信号电路的调整

副色调(1)的调整 (主茨屏, I²C总线控制, 子荧屏) 选择副色调调整状态, 然后, 接收"NTSC 制式彩条"信号。注接示波器于TP802(蓝色亮度)。 · ) , 前花图:20mV/段(交流电) • ) 刮频时间:20微秒/段 (使用10:1的探针) 3. 调节副色调(1)数据, 以获得图10所示的梯形波形。 4. 取消此项调整状态的设定。

2. 副色调(2)的调整 (子荧屏保养调整状态) 1. 选择副色调调整状态, 然后, 接收 "NTSC 制式彩条"信号。 2. 接示波器于CRT装置内的KY销(4)。(设主荧屏于无接收声象信号之状态) 3. 调节副色调(2)数据, 以获得图11所示的梯形物形

4.取消此项调整状态的设定。

图11

E22

C22

Page 23

SECAM CHROMA ADJUSTMENT

1 RELL FILTER TO ADJUSTMENT

(I²C bus adjustment)

1 Receive the "SECAM COLOUR BAR" signal Call the bell filter to adjustment mode
Can the ben inter to aujustment mode. Ground pin (32) of IC801 (IX2652CE) on the main PWB. (Just make a connection between TP902 and TP903 )
4. Connect the oscilloscope to pin (28) (TP901) of ICRO1 Range: 10 mV/div (AC)
Sweep time: 20 usec/div.
5. Adjust the bell filter data to have a waveform
6. Remove the connection between TP902 and TPOOR

2. SECAM BLACK LEVEL (R-Y/B-Y) ADJUSTMENT

(I²C bus adjustment)

1 Receive the "SECAM COLOUR BAR" signal
2. Call the SECAM black level adjustment R-X mode
3. Connect the oscilloscope to pin (40) (R-Y OUT, TP801) of IC801 Range: 10 mV/div
- Sweep time: 20 usec/div (Use a 10:1 probe)

4 Adjust the R-Y data so that the offset between the no-signal line and the signal line be minimum. See Fig. 13.
Call the SECAM black level adjustment B-Y mode Call the second black level aujustituting the second
TP802) of IC2851. Take the same conditions as in Adjust the B-Y data so that the offset between
the no-signal line and the signal line be minimum See Fig. 13

3. INSET PICTURE TRAP ADJUSTMENT

(I²C bus adjustment, inset picture service mode)
1. Call the inset picture service mode

Set the trap data to 3.

Fig. 12

■ SECAM 制式色度信号电路的调整

1 固尔地波程60的调款 (I²C总线控制) 1 接收"SRCAM制式影条" 信号 2. 选择贝尔波波器f0调整状态。 3 將主电路印刷电路板上的IC801 (IX2652CE)销(32)接地。(将TP902与 (19903法控町可) 4. 接示波器于IC801的值(28)(TP901) ●瀾示范閉:10mV/段(交流电) ●扫频时间:20微秒/段 (使用10.1的探针) 5.调节贝尔滤波器数据。以获得近似于图 12.所示的波形 6.拆去TP902与TP903的连接。

2.SECAM制式黑色信号电平(R-Y/B-Y)的调整

2. 选择SECAM制式黑色信号电平调整R-Y状

3.接示波器于IC801的销(40)(R-Y输出器

4.调节R-Y数据、使无信号线备与信号波形

6. 重新接示波器于IC2851的销(41)(B-Y输出

端。TP802)。按与3. 项相同的备件进行。

7.调节B-Y数据。使无信号线条与信号波形

间的误差幅值达至最小。见图13.

间的误差幅值达至最小贝图13 5. 选择SECAM制式黑色信号电平调整B-Y状态。

1.接收"SECAN制式彩条"信号。

(I²C总线控制)

杰

ТР801).

●测示范围:10mV/段

●扫翻时间 • 20 粉秒/段

(使用10・1的探针)

25113
3.子荧屏陷波的调整

(T²C总线控制。子炭屏保养调整状态) 1. 洗择子荧屏侵养调整状态。 2.设陷波数据于3位置。

Page 24

■ A/V INPUT AND OUTPUT CHECK

1. AUDIO/VIDEO OUTPUT CHECK

1. Receive the "PAL COLOUR BAR" signal (100% white colour bar, sound: 400 Hz, 100% mod.).
Terminate the video output with a 75-ohm impedance. Make sure the output is as specified (1.0 Vp-p±3 dB). Terminate the audio output with a 10-kohm impedance. Make sure the output is as specified
Terminate the audio output with a 10-kohm impedance. Make sure the output is as specified (1.76 Vp-p ± 3 dB).

2. AUDIO/VIDEO INPUT CHECK, S-TERMINAL INPUT CHECK

Using the TV/AV key on the remote controller, make sure that the modes change in the order of TV, AV1, AV2, AV3 and TV again and that the video and audio outputs are according to the input and output terminals for each mode.
Insert the connector in the S-VIDEO input jack and make sure the A/V mode changes to the S-VIDEO mode. See also if the picture and sound are normal and if the "AV1-S" and "AV3-S" are displayed on the screen.

PROTECTOR PERFORMANCE CHECK

1. BEAM PROTECTOR

1. Receive the "MONOSCOPE PATTERN" signal
2. Set the contrast control to maximum.
Set the brightness control to maximum.
Make a short-circuit between the collector and emitter of Q853 and make sure that the protector is activated and the stand-by mode is called.

2. HIGH-VOLTAGE PROTECTOR

1. Receive the "MONOSCOPE PATTERN" signal
Connect the bias box to the cathode (R635 side) of D609.
Adjust the bias box voltage to 16 V and make sure that the protector is not activated. Reference: usually about 19 V
Boost the bias box voltage to 22 V and make sure that the protector is activated.

3. OTHER PROTECTORS

In checking the performance of other protectors -- for example, the one against shorting of smoothing electrolytic capacitor of +B line --, pay attention not to damage or deteriorate any related element.

■音频/视频信号输入、输出的检查

1.音频/视频信号输入、输出的检查
1.接收"PAL制式彩条"信号(100%白色彩条,声音:400Hz、100%调制)。
2. 检查视频信号输出端的电阻为75Ω时的信号强度是否满足标准值的1.0Vp-p±3dB的规定要求。
检查音频信号输出端的电阻为10kΩ时的信号强度是否满足标准值的1.76Vp-p±3dB的规定要求。

2.音频/视频/S-视频端输入的检查

1.相继触按遥控器上的电视与录象切换(TV/AV)键,检查电视机信号输入频道是否按电视频道(TV),录象1频道(AV1)、录象2频道(AV2)、录象3频道(AV3)以及电视频道(TV)的顺序循环切换。并且,检查每一设定时的荧屏图象以及声音输出是否正常地与设定输入频道对应。
2. 设定AV1/AV3频道时,插S-视频插接头于其输入端,检查荧屏是否正常地由AV状态转为 S-视频状态。同时,检查荧屏上是否相应出现"AV1-S"和"AV3-S"字样的表示。

📕 保护电路性能的检查

1. 电子束保护电路
1.接收"单象管图案"信号。
2. 设对比度控制于最大位置。
3.设亮度控制于最大位置。
4. 短接Q853的集电极和发射极。检查这时的电子束保护电路是否被激励动作,电视机是否轴要干准条件太
一
2. 尚広保护电路 1 培收"虽象管图案"信号。
1. 接收"単象管因条"信号。 2. 接值压器于D609的阻极端(B635例)
2. 接偏压器于D609的阴极端(R635阀)。
3.将偏压器的电压调至16V、检查这时的高压保护电路是否被激励动作。
●参考数据:通常约为19V
4. 再将偏压器的电压调至22V, 检查这时的高压保护电路是否被激励动作。
3. 其它保护电路
在通过短接+B线路等的平流电解电容器进行该保护电路的检查时,注意切勿损伤、损坏电路元件。

Page 25

TROUBLE SHOOTING TABLE

故障检修流程图

Page 26

故障检修流程图(接上页)

E26

C26

Page 27

TROUBLE SHOOTING TABLE (Continued)

故障检修流程图(接上页)

Page 28

故障检修流程图(接上页)

其它图案:其它I²C总线控制用集成电路块或装置。 (具有SDA和SCL通道)

Other pattern:

Other I²C bus control ic or ur (It has SDA and SCL PORT.)

Page 29

TROUBLE SHOOTING TABLE (Continued)

故障检修流程图(接上页)

C29

E29

Page 30

E30

C30

Page 31

TROUBLE SHOOTING TABLE (Continued)

故障检修流程图(接上页)

电路。

C31

Page 32

TROUBLE SHOOTING TABLE (Continued)

E32

C32

Page 33

TROUBLE SHOOTING TABLE (Continued)

故障检修流程图(接上页)

C33

29HX8

E33

Page 34

Memo

Page 35

PRINTED WIRING BOARD ASSEMBLIES

(All the PWBs here are shown as viewed from their wiring sides.)

印刷电路板的组装件

(这里所有印刷电路都是从线路贴置侧显示出来的。)

Page 36

Page 37

Page 38

Page 39

Page 40

3.路装置

Page 41

Page 42

Page 43

Page 44

PWB-I:TELETEXT Unit (29HX5 only) 电视文字表示电路装置(只限于型号29HX5)

. も路装置

Page 45

Page 46

PWB-D : CTI Unit CTI电路装置

Page 47

DESCRIPTION OF SCHEMATIC DIAGRAM

CAUTION: This circuit diagram is original one, therefore there may be a slight difference from yours

SAFETY NOTE

1. DISCONNECT THE AC PLUG FROM THE AC OUTLET BEFORE REPLACEING PARTS
2. SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS OPERATING

IMPORTANT SAFETY NOTICE:

PARTS MARKED WITH "A" ( IMPORTANT FOR MAINTAINING THE SAFETY OF THE SET. BE SURE TO REPLACE THESE PARTS WITH SPECIFIED ONES FOR MAINTAINING THE SAFETY AND PERFORMANCE OF THE SET.

SERVICE PRECAUTION:

THE AREA ENCLOSED BY THIS LINE ( 1 15 DIRECTLY CONNECTED WITH AC MAINS VOLTAGE. WHEN SERVICING THE AREA, CONNECT AN ISOLATING TRANSFORMER BETWEEN TV RECEIVER AND AC LINE TO ELIMINATE HAZARD OF ELECTRIC SHOCK.

NOTES

1. The unit of resistance "ohm" is omitted. (K = 1000 ohms, M = Meg ohm).
2. All resistors are 1/8 watt, unless otherwise noted.
3. All capacitors are µF, unless otherwise noted. (P = μμF).
4. The diodes, whose parts code is not described, are the 155119

VOI TAGE MEASUREMENT CONDITIONS:

1. The voltage without parenthesis represents the value measured with PAL colour signal.
2. The voltage in parenthesis represents the value measured with no signal.
3. All the voltages were measured by using a high impedance voltmotor

WAVEFORM MEASUREMENT CONDI-TIONS

1. The colour bar signal applied to the TP202 is 2.0 VD-D.
2. The tuner AGC voltage is approximately 4V.

注意:这里的电路原理图均为最初设计师	原图,与您的机器的电路原理可能有不同之处。
安全注意事项:	电路单位说明:
1.更换电路元件时,必须先拔出电源插头,切	1.电阻欧姆(Ω)单位予以略记(K=千欧姆,
断电源。	M=兆欧姆)。
\|2.机芯底盘电路处工作状态时,应注意电路中\|	2.除特别说明者外,图中电阻功率均为1/8瓦特。
\| 半导体元件散热片高电位可能导致的电击危\|	3.除特别说明者(P=微微法拉)外,图中电容
险。	单位均为 μ F(微法拉)。
安全使用注意要点:	4.除特别说明者外,图中二极管均为1SS119。
标有" ^小 "( 标有" ^小 "( 标有" ^小 "( 机长久的安全使用起重要的元件。更换这些元件时,必须使用规定的纯正正牌元件,以保证本机的使用安全以及使用寿命	电压测定条件: 1.括号外的电压值为PAL制式彩色信号状态下所测。
	2. 括号中的电压值为无信号状态下所测。
维修注意事项:	3. 所有的电压值均由高阻抗电压计所测。
电路中由点划线(—————)所围部分为与
交流电源直接相接线路。对这些部分的线路进	波形测定条件:
行维修时,应于本机与交流电源之间用隔离变	1.施加于TP202的彩条信号应为2.0Vp-p。
压器相接,以防止不意的电击之危险。	2.调谐器AGC(自动增益控制)电压约为4V。

电路原理图的说明

Page 48

Page 49

Page 50

WAVE FORMS 波形图

Page 51

Page 52

Page 53

29HX5 29HX8

MODEL 29HX8 SCHEMATIC DIAGRAM

型号29HX8 电路原理图

■ IF/AV Unit-1/2 ■中频/声象电路装置—1/2

PWB-E (IF/AV UNIT) DUNTK8779WEVO

Page 54

CAUTION: This circuit diagram is original one, therefore there may be a slight difference from yours.

注意:这里的电路原理图均为最初设计原图,与您的机器电路原理图可能有不同之处。

Page 55

Page 56

CAUTION: This circuit diagram is original one, therefore there may be a slight difference from yours.

注意:这里的电路原理图均为最初设计原图,与您的机器电路原理图可能有不同之处。

Page 57

MODEL 29HX8 SCHEMATIC DIAGRAM P-IN-P Unit

型号29HX8 电路原理图

■ P-IN-P Unit ■双图象电视电路装置

Page 58

注意:这里的电路原理图均为最初设计原图,与您的机器电路原理图可能有不同之处。

Page 59

Page 60

^- Socket Unit

CAUTION: This circuit diagram is original one, therefore there may be a slight difference from yours. 注意:这里的电路原理图均为最初设计原图,与您的机器电路原理图可能有不同之处。

WB-H (CONTROL UNIT) UNTK8774WEVO

Page 61

Page 62

Page 63

29HX5 29HX8

MODEL 29HX5 SCHEMATIC DIAGRAM IF/AV Unit-1/2 型号29HX5 电路原理图

■中频/声象电路装置-1/2

Page 64

CAUTION: This circuit diagram is original one, therefore there may be a slight difference from yours.

注意:这里的电路原理图均为最初设计原图,与您的机器电路原理图可能有不同之处。

Page 65

Page 66

Page 67

Page 68

CAUTION: This circuit diagram is original one, therefore there may be a slight difference from yours.

注意:这里的电路原理图均为最初设计原图,与您的机器电路原理图可能有不同之处。

Page 69

Page 70

Page 71

MODEL 29HX5 SCHEMATIC DIAGRAM ■ TELETEXT Unit 型号29HX5 电路原理图 ■电视文字表示电路装置

CAUTION: This circuit diagram is original one, therefore there may be a slight difference from yours.

注意:这里的电路原理图均为最初设计原图,与您的机器电路原理图可能有不同之处。

DUNTK8558WEV2

Page 72

^• Socket Unit

CAUTION: This circuit diagram is original one, therefore there may be a slight difference from yours. 注意:这里的电路原理图均为最初设计原图,与您的机器电路原理图可能有不同之处。

WB-H (CONTROL UNIT) UNTK8774WEV1

Page 73

Page 74

Page 75

29HX5

Page 76

Page 77

Page 78

29HX5 29HX8

SOLID STATE DEVICE BASE DIAGRAMS 固体器件基座图

ΕZΖ

Page 79

29HX5 29HX8

Page 80

Page 81

Page 82

NOTE:		📓 is 291	HX5 only.
注意	:用		表示的内容只适用于型号29HX5

Page 83

Page 84

Page 85

Page 86

NOTE:		is 291	HX5 only.
注意:	用		表示的内容只适用于型号29HX5

Page 87

Page 88

B-H (CONTROL UNIT) NTK8774WEV1/V0

Page 89

Page 90

Ref. No.

PARTS LIST

PARTS REPLACEMENT

Replacement parts which have these special safety characteristics identified in this manual: electrical components having such features are identified by "\Delta" in the Replacement Parts Lists. The use of a substitute replacement part which does not have the same safety characteristics as the factory recommended replacement parts shown in this service manual may create shock, fire or other hazards.

"HOW TO ORDER REPLACEMENT PARTS"

To have your order filled promptly and correctly, please furnish the following informations.

1. MODEL NUMBER	2. REF. NO.
3. PART NO.	4. DESCRIPTION
5. CODE	6. QUANTITY

MARK * : SPARE PARTS-DELIVERY SECTION

Description

更换零件表

更换零件

本维修说明书对具有特别安全要求的零件均用标记加以识别; 在此更换零件表中,具有特别安全要求的电路元件均用本标记以便注意识别。更换零件时,为了用户的安全以及电视机原有的工作性能,务请使用夏普规定零件。否则,可能有导致触电、火灾或其他不测事故发生的可能。

更换零件的订货方法

为了能迅速而确实地接受订货、以及正确无误地按时交货,在订货时请将下列各项明确告知。

1. 型号	2. 参考编号
3. 零件编号	4. 零件名称
5. 代号	6. 数量
附★记号为彳	———————————————————— 备用部件的交货部门

Description

Code

Part No

⚠	VB68KYN697X*S	R CRT, 68 cm (29")	DE
Δ	RCiLG0045PEZZ	R Degaussing Coil	AY
∆ DY601	RCiLH0110PEZZ	R Deflection Yoke	BC
	PMAGF3038CEZZ	R Purity Magnet	AL
	PMAGG3002CEZZ	R Magnet	AC
	QEARC2901PEZZ	R Grounding Strap	Δκ

PRINTED WIRING BOARD ASSEMBLIES (NOT REPLACEMENT ITEM)

MODEL 29HX5


PWB-A	DUNTK8780WEV1	_	Main Unit
PWB-B	DUNTK8776WEV1		CRT Socket Unit	.
PWB-C	DUNTK8781WEV1	_	Power Unit
PWB-D	DUNTK8778WEV1	_	CTI Unit
PWB-E	DUNTK8779WEV1	-	IF/AV Unit
PWB-F	DUNTK8775WEV1	-	Front AV Unit	· ·
PWB-G	DUNTK8777WEV1	_	P-IN-P Unit
PWB-H	DUNTK8774WEV1	-	Control Unit
PWB-I	DUNTK8558WEV2	-	TELETEXT Unit

MODEL 29HX8

PWB-A DUNTK8780WEV0	_	Main Unit	-
PWB-B DUNTK8776WEV0	-	CRT Socket Unit
PWB-C DUNTK8781WEV0	-	Power Unit
PWB-D DUNTK8778WEV0	-	CTI Unit
PWB-E DUNTK8779WEV0	-	IF/AV Unit	_
PWB-F DUNTK8775WEV0	_	Front AV Unit
PWB-G DUNTK8777WEV0	-	P-IN-P Unit	-
PWB-H DUNTK8774WEV0	_	Control Unit	.

----- End of PICTURE TUBE

—— End of P.W.B. ASS'Y —

Code

Ref. No.

Part No

Page 91

Ref. No.

Part No

PARTS LIST

PARTS REPLACEMENT

"HOW TO ORDER REPLACEMENT PARTS"

To have your order filled promptly and correctly, please furnish the following informations.

1. MODEL NUMBER	2. REF. NO.
3. PART NO.	4. DESCRIPTION
5. CODE	6. QUANTITY

MARK ★ : SPARE PARTS-DELIVERY SECTION

Description

Code

Ref. No.

Part No.

鱼	换	雴	件	夫
×	1大	1	Т	1X

更换零件

本维修说明书对具有特别安全要求的零件均用标记加以识别: 在此更换零件表中,具有特别安全要求的电路元件均用查标记以便注意识别。更换零件时,为了用户的安全以及电视机原有的工作性能,务请使用夏普规定零件。否则,可能有导致触电、火灾或其他不测事故发生的可能。

更换零件的订货方法

为了能迅速而确实地接受订货、以及正确无误地按时交货,在订货时请将下列各项明确告知。

1. 型号	2. 参考编号
3. 零件编号	4. 零件名称
5. 代号	6. 数量
附★记号为	备用部件的交货部门	·

Description

Code

ļ	ΡΙ	C	Τι	JF	RE	Т	U	В	Ε

Δ	VB68KYN697X*S	R CRT, 68 cm (29")	DE
A	RCiLG0045PEZZ	R Degaussing Coil	AY
∆ DY601	RCiLH0110PEZZ	R Deflection Yoke	BQ
	PMAGF3038CEZZ	R Purity Magnet	AL
	PMAGG3002CEZZ	R Magnet	AC
	QEARC2901PEZZ	R Grounding Strap	AK

PRINTED WIRING BOARD ASSEMBLIES (NOT REPLACEMENT ITEM)

MODEL 29HX5

PWB-A	DUNTK8780WEV1	_	Main Unit
PWB-B	DUNTK8776WEV1	-	CRT Socket Unit
PWB-C	DUNTK8781WEV1	_	Power Unit
PWB-D	DUNTK8778WEV1	-	CTI Unit
PWB-E	DUNTK8779WEV1	-	IF/AV Unit
PWB-F	DUNTK8775WEV1	-	Front AV Unit
PWB-G	DUNTK8777WEV1	_	P-IN-P Unit
PWB-H	DUNTK8774WEV1	_	Control Unit
PWB-I	DUNTK8558WEV2	-	TELETEXT Unit


	MOD	EL	29HX8

PWB-A DUNTK8780WEV0	Main Unit
PWB-B DUNTK8776WEV0	CRT Socket Unit
PWB-C DUNTK8781WEV0	- Power Unit
PWB-D DUNTK8778WEV0	– CTI Unit
PWB-E DUNTK8779WEV0	– IF/AV Unit
PWB-F DUNTK8775WEV0	Front AV Unit
PWB-G DUNTK8777WEV0	– P-IN-P Unit
PWB-H DUNTK8774WEV0	Control Unit

----- End of PICTURE TUBE

— End of P.W.B. ASS'Y —

Page 92

Page 93

Code

AB AB AC AB AB AC AC AB AB

АА

AA АА AA AA АА АА AB АВ AA АА AA AA AB АА AA AA АВ

AB AA

AA AA АА AA

AA AA

ΑВ

AA АА

AA AA

Ref. No.	Part No.	*	Description	Code	Ref. No.	Part No.	*	Description
D\\/F		KS	780W/F\/1/\/0		01014	V$2$C1815GW/-1	R	2SC1815GW/
L AAF		NU			01601	VS2SC1815GW 1	R	2901019000
	MAIN U	JNI	Т		01602	VS2SC1015UV-1	P	2501015000
		тег			01604	VS2SC1815GW-1	R	25C1815GW/
10201			Audio Lovel Control	٨G	01605	VS2SC1815GW-1	R	25C1815GW
10301		n D	Audio Level Control		01605	VS2SC1815UV-1	R	2501015077
10302	VHIAN/395K/-1	n D	Spatializer		01607	VS2SA10151/1E	P	25A10151
10303	VHIUPC1853CZE	к	Sound Control (Surround)		01607	V525A10151/1E	n D	25A10151
10304	VHI1A8216H/-1	К	Audio Amp. (Front)		01608	VS25C1815GW-1	n D	25C1015GW
10305	VHIDA1519AQ-1	ĸ			01609	V525C1815GW-1	n	2301013000
10306	VHINJM2058D-1	п п	Bass Amp. (AST Drive)	AG
10401	VHINJMZZ49D-T	п				г	νοι	)FS
10402	VHITA1226N/-1	R D	SRI Martinal Output		D201			Diada 199119
10501		n D	Vertical Output		D301		P	Zoper Diode, 6 2V
10502	VHITA8859CP-T	R D			D302		n D	Zener Diode, 6.2V
10801		n D	PCP DAC (Pice/Drive)		D303			Diodo 199119
101001	VHITA8889AP-T	R	RGB DAC (Blas/Drive)		D304	VHD155119//1E	n D	Diode, 155119
101001	RH-IX265UCEZZ	R			D305		n P	Diode, 155119
101002	RH-IXZZ8/CEZZ	к		85	D300	VHD155119//1E	n D	Diode, 155119
101003	KH-IX265 ICEZZ	R R			D307		n D	Diode, 133119
101006		к р	5V Regulator		D308		R	Zener Diode 30V
101007		n D			D309		R	Zener Diode, 30V
101008		n D			D310		R	Diode 199119
101009	VHINA/809FI-1	n D			D311		R	Diode, 155119
101010	VHIPST529C2-1	n D	Reset		D312	VHD155119//1E	R	Diode, 155119
101011	VHIPS1529C2-1	n p	12)/ Requistor		D313	VHD155119//1E	R	Diode, 155119
101012		n D	Video Switch		D314	RH-EX0395GEZZ	R	Zener Diode 9V
101602		R	5\/ Begulator (29HX5)		D316	VHD1SS119//1E	R	Diode 1SS119
101002	VIIIKA7805FFT		5V Regulator (2511/(5)		D317	BH-EX0395GEZZ	R	Zener Diode, 9V
					D318	RH-FX0408GEZZ	R	Zener Diode, 12V
	TRA	NSI	STORS		D319	VHD1SS119//1E	R	Diode, 1SS119
0301	VS2SC1815GW-1	R	2SC1815GW	AB	D320	VHD1SS119//1E	R	Diode, 1SS119
0302	VS2SC1815GW-1	R	2SC1815GW	AB	D321	VHD1SS119//1E	R	Diode, 1SS119
Q303	VS2SC1815GW-1	R	2SC1815GW	AB	D322	RH-EX0695GEZZ	R	Zener Diode, 30V
Q304	VS2SC1815GW-1	R	2SC1815GW	AB	D323	RH-EX0695GEZZ	R	Zener Diode, 30V
Q403	VS2SC1815GW-1	R	2SC1815GW	AB	D402	RH-EX0301CEZZ	R	Zener Diode, 6.2V
Q404	VS2SA1015Y/1E	R	2SA1015Y	AC	D403	VHD1SS119//1E	R	Diode, 1SS119
Q405	VS2SK30AG//2E	R	2SK30AG	AD	D407	RH-EX0301CEZZ	R	Zener Diode
Q410	VS2SC1815YW-1	R	2SC1815Y	AC	D410	VHD1SS119//1E	R	Diode, 1SS119
Q412	VS2SC1815GW-1	R	2SC1815GW	AB	D411	VHD1SS119//1E	R	Diode, 1SS119
Q415	VS2SC1815GW-1	R	2SC1815GW	AB	D501	RH-EX0301CEZZ	R	Zener Diode, 6.2V
Q416	VS2SC1815GW-1	R	2SC1815GW	AB	D502	RH-EX0301CEZZ	R	Zener Diode, 6.2V
Q501	VS2SC1815GW-1	R	2SC1815GW	AB	D503	RH-EX0301CEZZ	R	Zener Diode, 6.2V
Q804	VS2SC1815GW-1	R	2SC1815GW	AB	D504	RH-DX0279CEZZ	R	Diode
Q901	VS2SC1815GW-1	R	2SC1815GW	AB	D505	RH-EX0301CEZZ	R	Zener Diode, 6.2V
Q1001	VS2SA1015Y/1E	R	2SA1015Y	AC	D506	VHD1SS119//1E	R	Diode, 1SS119
Q1002	VS2SA1015Y/1E	R	2SA1015Y	AC	D801	VHD1SS119//1E	R	Diode, 1SS119 (29HX5)
Q1003	VS2SC1815GW-1	R	2SC1815GW	AB	D805	RH-EX0301CEZZ	R	Zener Diode, 6.2V
Q1004	VS2SC1815GW-1	R	2SC1815GW	AB	D806	RH-EX0301CEZZ	R	Zener Diode, 6.2V
Q1005	VS2SC1815GW-1	R	2SC1815GW	AB	D807	RH-EX0322CEZZ	R	Zener Diode, 12V
Q1006	VS2SC1815GW-1	R	2SC1815GW	AB	D808	RH-EX0322CEZZ	R	Zener Diode, 12V
Q1007	VS2SC1815GW-1	R	2SC1815GW	AB	D809	RH-EX0322CEZZ	R	Zener Diode, 12V
Q1010	VS2SC1815GW-1	R	2SC1815GW	AB	D810	VHD1SS119//1E	R	Diode, 1SS119
Q1011	VS2SC1815GW-1	R	2SC1815GW	AB	D1001	VHD1SS119//1E	R	Diode, 1SS119
Q1012	VS2SC1815GW-1	R	2SC1815GW	AB	D1002	RH-EX0301CEZZ	R	Zener Diode, 6.2V
Q1013	VS2SC1815GW-1	R	2SC1815GW	AB	D1003	RH-EX0301CEZZ	R	Zener Diode, 6.2V

____

Page 94

-	29HX 29HX	5
_	Ref. No.	. Pa	art No.		Description	C	ode	Ref. No.	Part No.		* Description	Code
	PW	B-A	DUNT	Κ	3780WEV1/	V0		D1059	RH-EX0358GEZZ	F	R Zener Diode	AR
			ΜΑΙΝ Ι	JN	IT (Continue	d)		D1060	VHD1SS119//1E	F	R Diode, 1SS119	AA
-			DIODE					D1061	VHD1SS119//1E	F	Piode, 1SS119	AA
	D1004			5 (C	continued)			D1062	VHD1SS119//1E	F	R Diode, 1SS119	AA
	D1004		0301CEZZ	R	Zener Diode, 6.2V	, ,	4A • •	D1063	RH-EX0301CEZZ	F	Zener Diode, 6.2V	AA
	D1000	BH-EX	1301CEZZ	R	Zener Diode, 6.2V		4A A A	D1064	RH-EX0301CEZZ	F	Zener Diode, 6.2V	AA
	D1007	RH-EX	0301CEZZ	R	Zener Diode, 6.2V	, ,	4A A A	D1065	RH-EX0301CEZZ	۲ -	Zener Diode, 6.2V	AA
	D1008	RH-EX	0301CEZZ	R	Zener Diode, 6.2V		4.Α Δ.Δ	D1060		r c	Cener Diode, 6.2V	AA
	D1009	RH-EX	0301CEZZ	R	Zener Diode, 6.2V		4A	D1068	RH-EX0301CEZZ	F	Zener Diode, 6.2V	AA
	D1010	RH-EX(	0301CEZZ	R	Zener Diode, 6.2V		4A	D1069	RH-EX0301CEZZ	F	Zener Diode, 6.2V	AA
	D1011	RH-EX	301CEZZ	R	Zener Diode, 6.2V	,	٩A	D1070	RH-EX0301CEZZ	В	Zener Diode, 6.2V
	D1012	RH-EX(	0301CEZZ	R	Zener Diode, 6.2V	,	٩A	D1071	RH-EX0301CEZZ	В	Zener Diode, 6.2V
	D1013	RH-EX(	301CEZZ	R	Zener Diode, 6.2V		٩A	D1077	VHD1SS119//1E	R	Diode, 1SS119	ΔΔ
	D1014	RH-EX(	0301CEZZ	R	Zener Diode, 6.2V	/	٩A	D1078	VHD1SS119//1E	R	Diode, 1SS119	AA
	D1015	RH-EX(	301CEZZ	R	Zener Diode, 6.2V	/	٩A	D1079	VHD1SS119//1E	R	Diode, 1SS119	AA.
	D1016	RH-EX(	301CEZZ	R	Zener Diode, 6.2V	ļ	٩A	D1080	VHD1SS119//1E	R	Diode, 1SS119	AA
	D1017	RH-EXC	301CEZZ	R	Zener Diode, 6.2V	ļ	чA	D1601	VHD1SS119//1E	R	Diode, 1SS119	AA
	D1018	VHD15	S119//1E	R	Diode, 1SS119	Å	٩A	D1602	RH-DX0279CEZZ	R	Diode	AB
	D1019		S119//1E	К	Diode, 1SS119	A	4A	D1603	RH-EX0291CEZZ	R	Zener Diode, 4.7V	AA
	D1020		2010522	R	Zener Diode, 6.2V	· /		D1604	VHD1SS119//1E	R	Diode, 1SS119 (29HX5)	AA
	D1021	RH-EXC	3010622	R D	Zener Diode, 6.2V	4		D1605	VHD1SS119//1E	R	Diode, 1SS119 (29HX5)	AA
	D1022	RH-EXO	3010622	R	Zener Diode, 6.2V	,		D1606	VHD1SS119//1E	R	Diode, 1SS119 (29HX5)	AA
	D1024	RH-FX0	301CEZZ	R	Zener Diode, 6.2V			D1607	RH-EX0281CEZZ	R	Zener Diode, 3.3V	AA
	D1026	RH-EX0	301CEZZ	R	Zener Diode, 6.2V		Δ	D1608		· K	Zener Diode, 9.1V	AA
	D1027	RH-EX0	301CEZZ	R	Zener Diode, 6.2V		A	D1611	VHD155119//1E	R	Diode, 1SS119 Diode, 1SS119	AA
	D1028	RH-EX0	301CEZZ	R	Zener Diode, 6.2V	Â	A	D1612	VHD1SS119//1E	R	Diode, 155119
	D1029	RH-EX0	325CEZZ	R	Zener Diode, 13V	Д	A	27012	THE TOO HOW TE		Dioue, 155119	АА
	D1031	RH-EX0	325CEZZ	R	Zener Diode, 13V	A	А
	D1032	RH-EX0	325CEZZ	R	Zener Diode, 13V	Д	А		PACKAG	GED	CIRCUITS
	D1033	RH-EX0	325CEZZ	R	Zener Diode, 13V	A	A	X801	RCRSB0067CEZZ	R	Crystal, 4.43MHz	AQ
	D1034	RH-EX0	325CEZZ	R	Zener Diode, 13V	А	A	X802	RCRSB0001PEZZ	R	Crystal, 3.58MHz	AL
	D1035	RH-EX0	301CEZZ	R	Zener Diode, 6.2V	А	А
	D1036	RH-EX0	301CEZZ	R	Zener Diode, 6.2V	А	А
	D1037		5119//1E	К	Diode, 1SS119	А	A		COIL AND T	RA	NSFORMERS
	D1038	BH-EX0	301CEZZ	n P	Zener Diode, 6.2V	A	A	CF1001	RFiLA0084CEZZ	R	Filter, 7.2MHz Clock Osc.	AE
	D1040	RH-EXO	325CE77	R	Zener Diode, 6.2V	A	A ^	CF1002	RFILC0091GEZZ	R	Filter, Oscillator	AD
	D1041	RH-EX0	325CEZZ	R	Zener Diode, 13V	Δ	Α Δ			К	Filter, VCO 503kHz	AD
	D1042	RH-EX0	B01CEZZ	R	Zener Diode, 6.2V	A	A		VP-XF330K0000	n R
	D1043	RH-EX03	B01CEZZ	R	Zener Diode, 6.2V	A	A	1403	VP-DF220K0000	n. R
	D1044	RH-EX03	B01CEZZ	R	Zener Diode, 6.2V	A	A	L501	VP-DF101K0000	R	Peaking Coil, 22µ1
	D1045	RH-EX03	B01CEZZ	R	Zener Diode, 6.2V	A	А	L801	VP-XF180K0000	R	Peaking Coil, 18uH	AB
	D1046	RH-EX03	B01CEZZ	R	Zener Diode, 6.2V	A	Ą	L802	VP-XF150K0000	R	Peaking Coil, 15µH	AB
	D1047	RH-EX03	301CEZZ	R	Zener Diode, 6.2V	A	д	L803	VP-DF220K0000	R	Peaking Coil, 22µH	AB
	D1048	RH-EX03	B01CEZZ	R	Zener Diode, 6.2V	A	д	L901	VP-XF180K0000	R	Peaking Coil, 18µH	AB
	D1049	VHD1SS	119//1E	R	Diode, 1SS119	A	д	L1001	VP-DF1R0K0000	R	Peaking Coil, 1µH	AB
	D1051	VHD1SS	119//1E	R	Diode, 1SS119	A	4	L1002	VP-DF1R0K0000	R	Peaking Coil, 1µH	AB
	D1052	VHD1SS	119//1E	R	Diode, 1SS119	A	٩	T1001	RCiLB0008PEZZ	R	Oscillation Coil, OSD	AG
	D1053	VHD1SS	119//1E	R	Diode, 1SS119	A	4
	D1054	VHD1SS	119//1E	RI	Diode, 1SS119	A	ч				D .01
	D1055		119//1E	к I р	Diode, 188119	A/	7	DAGGE	СО	NT	KOL
	D1050	VHD166	119// IE 119//1E	ר ד פי	Jiode, 188119	AA	4 \	K1609	KVK-M4634GEZZ	R	220k(B) Sub-Contrast	AB
	D1058	VHD199	119//1E	n I R I	Diode, 133119	AA	٦ ١
						A/

Page 95

Ref. No.	Part No.	1	*	Descrip	otion (	Code	Ref. No.	Part No.	*		Descrip	otion	Code
PWE	B-A DUNT	κ	3780	WΕν	/1/V0		C353	VCEAGH2AW/337M	R	330	100\/	Electrolytic
							C354	VCEAGH2AW337M	R	330	1001	Electrolytic
	MAINU	JN	II (Ce	ontin	ued)		C355	VCEYEA1HA2241	R	0.22	501
	CAF	PAC	TORS				C356	VCEAGA1HW224M	R	0.22	50V	Flectrolytic
C301	VCEAGA1CW107M	1 R	100	16V	Electrolytic	AB	C357	VCQYTA1HM104J	R	0.22	50V	Mylar	ΔΔ
C302	VCEAGA1CW107N	1 R	100	16V	Electrolytic	AB	C358	VCEAGA1VW476M	R	47	35V	Electrolytic	ΔR
C303	VCEAGA1CW106N	1 R	10	16V	Electrolytic	ΔΔ	C359	BC-E70287CE77	R	47	50V
C304	VCEAGA1CW106N	1 R	10	16V	Electrolytic	AA	C360	BC-EZ0287CEZZ	R	4.7	50V	Elect (N.P)	ΔF
C305	VCEAGA1CW106N	1 R	10	16V	Electrolytic	AA	C361	VCEAGA1VW228M	R	2200	35V	Electrolytic	AR
C306	VCEAGA1CW106N	1 R	10	16V	Electrolvtic	AA	C362	VCEAGA1EW228M	R	2200	25V	Electrolytic	AF
C307	VCEAGA1CW226N	1 R	22	16V	Electrolytic	AB	C363	VCQYTA1HM104J	R	0.1	50V	Mvlar	AA
C308	VCEAGA1CW337N	1 R	330	16V	Electrolytic	AC	C365	VCEAGA1HW475M	R	4.7	50V	Electrolytic	AB
C309	VCEAGA1CW106M	1 R	10	16V	Electrolytic	AA	C366	VCQYTA1HM104J	R	0.1	50V	Mylar	AA
C310	VCEAGA1CW106M	1 R	10	16V	Electrolytic	AA	C367	VCFYFA1HA334J	R	0.33	50V	M. Polyeste	r AB
C311	VCQYTA1HM393J	R	0.039	50V	Mylar	AA	C368	VCFYFA1HA334J	R	0.33	50V	M. Polveste	r AB
C312	VCQYTA1HM563J	R	0.056	50V	Mylar	AB	C369	VCQYTA1HM223J	R	0.022	50V	Mylar	AA
C313	VCEAGA1CW107M	1 R	100	16V	Electrolytic	AB	C370	VCFYFA1HA184J	R	0.18	50V	M. Polyeste	r AC
C314	VCEAGA1CW106M	1 R	10	16V	Electrolytic	AA	C371	VCKYPA1HF103Z	R	0.01	50V	Ceramic	AA
C315	VCKYPA1HF103Z	R	0.01	50V	Ceramic	AA	C372	VCFYFA1HA224J	R	0.22	50V	M. Polyeste	r AB
C316	VCEAGA1CW106M	1 R	10	16V	Electrolytic	AA	C373	VCFYFA1HA474J	R	0.47	50V	M. Polyeste	r AC
C317	VCEAGA1CW226N	1 R	22	16V	Electrolytic	AB	C374	VCQYTA1HM473J	R	0.047	50V	Mylar	AA
C318	VCEAGA1HW105M	1 R	1	50V	Electrolytic	AC	C375	VCE9GA1CW106M	R	10	16V	Elect. (N.P)	AB
C319	VCKYPA1HF103Z	R	0.01	50V	Ceramic	AA	C376	VCEAGA1CW337M	R	330	16V	Electrolytic	AC
C320	VCQYTA1HM273J	R	0.027	50V	Mylar	AB	C377	VCEAGA1AW227M	R	220	10V	Electrolytic	AB
C321	VCEAGA1CW107M	1 R	100	16V	Electrolytic	AB	C378	VCFYFA1HA474J	R	0.47	50V	M. Polyeste	r AC
C322	VCEAGA1HW335M	⁄l ⊢R	3.3	50V	Electrolytic	AB	C379	VCFYFA1HA474J	R	0.47	50V	M. Polyeste	r AC
C323	VCEAGA1HW335N	/IR	3.3	50V	Electrolytic	AB	C380	VCFYFA1HA474J	R	0.47	50V	M. Polyeste	r AC
C324	VCEAGA1CW226N	1 R	22	16V	Electrolytic	AB	C381	VCFYFA1HA474J	R	0.47	50V	M. Polyeste	r AC
C325	VCEAGA1CW226N	1 R	22	16V	Electrolytic	AB	C382	VCEAGA1HW105M	R	1	50V	Electrolytic	AC
C326	VCEAGA1CW226N	1 R	22	16V	Electrolytic	AB	C383	VCFYFA1HA224J	R	0.22	50V	M. Polyeste	r AB
C327	VCEAGA1CW226N	1 R	22	16V	Electrolytic	AB	C384	VCFYFA1HA224J	R	0.22	50V	M. Polyeste	r AB
C328	VCCSPA1HL681J	R	680p	50V	Ceramic	AA	C385	VCEAGA1CW476M	R	47	16V	Electrolytic	AB
C329	VCQYTA1HM823J	R	0.082	50V	Mylar	AA	C386	VCQYTA1HM473J	R	0.047	50V	Mylar	AA
C330	VCQYTA1HM104J	R	0.1	50V	Mylar	AA	C387	VCE9GA1CW106M	R	10	16V	Elect. (N.P)	AB
C331	VCQYTA1HM222J	R	2200p	50V	Mylar	AA	C388	VCKYPA1HF103Z	R	0.01	50V	Ceramic	AA
C332	VCQYTA1HM223J	R	0.022	50V	Mylar	AA	C389	VCKYPA1HF103Z	R	0.01	50V	Ceramic	· AA
C333	VCQYTA1HM223J	R	0.022	50V	Mylar	AA	C390	VCKYPA1HF103Z	R -	0.01	50V	Ceramic	AA
C334	VCQYTA1HM102J	К	1000p	50V	Mylar	AA	C403	VCEAGA1CW107M	R	100	16V	Electrolytic	AB
0335		К	0.1	500	Wylar	AA	C404	VCKYPATHF103Z	К	0.01	50V	Ceramic
C335		К	0.1	50V	Mular		C405	VCQYTATHIVI104J	K.	0.1	50V ·	Wylar	АА
C337		л 0	6800p	507	Mular		CADE		Б	(29HX	5)	Electrolutio	• •
C330		n A D	2.2	507	Floatrolutio		C405		п	10	. 16V	Caramia
C240		/\| D	2.2	501	Electrolytic		C408			0.01	501	Coramia
C241	VCKVPA1HE1027	" " B	0.01	507	Coramio		C407			ο 2μ	500	Mular
C347		18	1000	16V	Electrolytic		C408		R	100	161/	Electrolytic
C342		1 8	1000	161/	Electrolytic		C409		R	0.01	161/	Coramio
C343		1 8	47	16V	Electrolytic		C410	VCEAGA1CW/106M	R	10	16\/	Electrolytic
C345		1 R	1	50V	Electrolytic	AC	C412		R	0.1	501/	Mylar	ΔΔ
C346		/ R	1	501/	Electrolytic	AC	C412		R	0.01	501/	Ceramic	ΔΔ
C347		R	' 1000n	50V	Mylar	ΔΔ	C413	VCCCPA1HH3301	R	33n	501/	Ceramic	ΔΔ
C348	VCOYTA1HM102J	R	1000p	50V	Mylar	ΔΔ	C414 C415	VCCSPA1HL 101.1	R	100n	501/	Ceramic	AA
C349	VCOYTA1HM2221	R	2200n	50V	Mylar	ΔΔ	C416	VCEAGA1HW224M	R	0.22	50V	Electrolytic	AA
C350	VCQYTA1HM2221	R	2200n	50V	Mylar	AA	C418	VCEAGA1HW225M	R	2.2	50V	Electrolytic	AB
C351	VCEAGA1CW476M	1 R	47	16V	Electrolytic	AB	C419	VCEAGA1CW106M	R	10	16V	Electrolytic	AA
C352	VCFYFA1HA224J	R	0.22	50V	M. Polvester	r AB	C420	VCEAGA1CW106M	R	10	16V	Electrolvtic	AA

Page 96

29HX 29HX	5
Ref. No.	Pa	rt No.	7	*	Descri	ption	Code	Ref. No.	Part No.	۲	۲	Descri	ption	Code
PW	B-A			3780 UT (C	WE	V1/V0		C818	VCCCPA1HH390J	R	39p (29HX	50V	Ceramic	AA
					οπτιι	nuea)		C819	VCKYD41CY103N	R	0.01	.0, 16V	Ceramic	ΔΔ
	С	APACITO	RS	6 (Con	tinue	d)		C821	VCCCPA1HH330J	R	33p	50V	Ceramic	AA
C432	VCOYT	A1HM104J	R	0.1	50V	Mylar	AA	C822	VCKYD41CY103N	R	0.01	16V	Ceramic	AA
C434	VCQYT	41HM104J	R	0.1	50V	Mylar	AA	C823	VCQYTA1HM104J	R	0.1	50V	Mylar	AA
C435	VCQYT	A1HM104J	R	0.1	50V	Mylar	AA	C824	VCEAGA1HW105M	R	1	50V	Electrolytic	AC
C436	VCUYI	41HM104J	R	0.1	50V	Mylar	AA	C825	VCCCPA1HH330J	R	33p	50V	Ceramic	AA
C437	VCEAG		К	4./	50V	Electrolytic	AB	C827	VCQYTA1HM104J	R	0.1	50V	Mylar	AA
C430	VCEAG	A1CW/105M	R	1 10	50V 16V	Electrolytic		C829		R	0.1	50V	Mylar	AA
C440	VCKYD	41CY103N	R	0.01	16V	Ceramic		C841		К	4/p	50V	Ceramic	AA
C441	VCEAG	A1CW106M	R	10	16V	Electrolytic		C842		к р	4/p	50V	Ceramic	AA
C442	VCKYPA	1HF103Z	R	0.01	50V	Ceramic	ΑΑ	C845		n B	47p 1	501	Electrolutio	AA
				(29HX	5)	ooranno	,	C848	VCEAGA1HW475M		47	501	Electrolytic
C442	VCKYD4	41CY103N	R	0.01	16V	Ceramic	AA	C849	VCKYD41CY103N	R	0.01	16V	Ceramic
				(29HX	8)			C901	VCEAGA1HW105M	R	1	50V	Electrolytic	AC
C443	VCEAG	41CW477M	R	470	16V	Electrolytic	AC	C902	VCCCPA1HH820J	R	82p	50V	Ceramic	AA
C444	VCEAG	41HW225M	R	2.2	50V	Electrolytic	AB	C903	VCQYTA1HM104J	R	0.1	50V	Mylar	AA
C445	VCEAG	A1CW106M	R	10	16V	Electrolytic	AA	C904	VCCCPA1HH820J	R	82p	50V	Ceramic	AA
C446	VCEAG	A1HW225M	R	2.2	50V	Electrolytic	AB	C905	VCQYTA1HM223J	R	0.022	50V	Mylar	AA
C448	VCEAG	A1CW337M	R	330	16V	Electrolytic	AC	C906	VCCCPA1HH270J	R	27p	50V	Ceramic	AA
C450	VCCCPA	1HH330J	R	33p	50V	Ceramic	AA	C907	VCKYPA1HF103Z	R	0.01	50V	Ceramic	AA
C451	VCCCPA		К	0.01	50V	Ceramic	AA	C908	VCCCPA1HH220J	R	22p	50V	Ceramic	AA
C452	VCEAGA		R	82p 0.33	501	Ceramic Electrolutio		C909	VCKYD41CY103N	R	0.01	16V	Ceramic	AA
C502	VCEACA	1HC2251	R	2.2	50V	Electrolytic	AC	C910		К	0.1	50V	Mylar	AA
C503	VCOYTA	1HM223J	R	0.022	50V	Mylar		C1001		n R	330	16V	Electrolytic
C504	VCEAGA	A1CW108M	R	1000	16V	Electrolvtic	AD	C1001	VCEAGA1HW105M	R	1	50V	Electrolytic
C505	VCKYPA	1HF103Z	R	0.01	50V	Ceramic	AA	C1003	VCCSPA1HL220J	R	22n	50V	Ceramic
C506	VCEAGA	A1HW107M	R	100	50V	Electrolytic	AC	C1004	VCCSPA1HL220J	R	22p	50V	Ceramic	AA
C507	VCQYTA	1HM103J	R	0.01	50V	Mylar	AA	C1005	VCCSPA1HL220J	R	22p	50V	Ceramic	AA
C508	VCQYTA	1HM683J	R	0.068	50V	Mylar	AB	C1006	VCCSPA1HL220J	R	22p	50V	Ceramic	AA
C509	VCFYAA	2AA224J	R	0.22	100V	M. Polyeste	r AD	C1007	VCCSPA1HL560J	R	56p	50V	Ceramic	AA
C510	VCEAGA	1VW108M	R	1000	35V	Electrolytic	AD	C1008	VCCSPA1HL560J	R	56p	50V	Ceramic	AA
C511	VCEAGA	1VW108M	R	1000	35V	Electrolytic	AD	C1009	VCEAGA1AW107M	R	100	10V	Electrolytic	AB
C512	VCEAGA		н	1	50V	Electrolytic	AC	C1010	VCKYPA1HF103Z	R	0.01	50V	Ceramic	AA
C513		1CV102N	н D	0.47	50V	Electrolytic	AB	C1012	VCEAGA1HW475M	R	4.7	50V	Electrolytic	AB
C514	VCCSPA	1HI 221.1	R	220n	10V 50V	Ceramic		C1013	VCEAGATHW105M	.H p	1	50V	Electrolytic	AC
C517	VCEACA	1HC225J	R	2.2	50V	Electrolytic	AC	C1014		n R	10	50V 16V	Electrolytic
·C518	VCKYPA	2HB391K	R	390p	500V	Ceramic	AA	C1016	VCEAGA1CW100M	R	100	101/	Electrolytic
C519	VCEAGA	1HW105M	R	1	50V	Electrolytic	AC	C1017	VCEAGA1EW107M	R	100	25V	Electrolytic
C520	VCQYTA	1HM683J	R	0.068	50V	Mylar	АВ	C1018	VCEAGA1CW107M	R	100	16V	Electrolytic	AB
C806	VCKYPA	1HF103Z	R	0.01	50V	Ceramic	AA	C1019	VCEAGA1CW227M	R	220	16V	Electrolytic	AC
C807	VCEAGA	1CW337M	R	330	16V	Electrolytic	AC	C1020	VCEAGA1EW227M	R	220	25V	Electrolytic	AC
C808	VCQYTA	1HM103J	R	0.01	50V	Mylar	AA	C1021	VCEAGA1CW227M	R	220	16V	Electrolytic	AC
C809	VCEAGA	1HW225M	R	2.2	50V	Electrolytic	AB	C1022	VCEAGA1EW227M	R	220	25V	Electrolytic	AC
C811	VCQYTA	1HM104J	R	0.1	50V	Mylar	AA	C1023	VCKYPA1HF103Z	R	0.01	50V	Ceramic	AA
C812	VCQYTA	1HM104J	R	0.1	50V	Mylar	AA	C1024	VCEAGA1HW105M	R	1	50V	Electrolytic	AC
C813	VCOYTA	THM223J	R	0.022	50V	Mylar	AA	C1025	VCCSPA1HL330J	R	33p	50V	Ceramic	AA
C814	VCCCPA	THH120J	К Р	12p	50V	Ceramic	AA	C1026	VCCSPA1HL330J	R	33p	50V	Ceramic	AA
C016	VCOVTA	1HM2221	ц Ц	iup 0.022	50V	Ceramic		C1027	VCCSPA1HL330J	К	33p 22	50V	Ceramic	AA
C817		111111223J	n R	0.022 22n	50V 50V	Ceramic		C1028	VCCSPATHLSSUJ	Ы	ззр Бе∽	50V	Ceramic	AA A A
5017	, 0001 A					Coranno	( )/¬	C1029	VCCSPA1HI 560 I	R	56n	501	Ceramic	ΑΑ ΔΔ
								2.000		••	~~~		Seramo

Page 97

Ref. No.	Part No.	*		Descrip	otion C	ode	Ref. No.	Part No.	*		Descri	ption	Code
PWE	B-A DUNTK	(8	780	WEV	/1/V0		R315	VRD-RA2EE105J	R	1M	1/4W	Carbon	АА
							R316	VRD-RA2BE223J	R	22k	1/8W	Carbon	АА
				οητιη	uea)		R317	VRD-RA2BE154J	R	150k	1/8W	Carbon	АА
	CAPACITOR	S	(Con	tinued	1)		R318	VRD-RA2BE472J	R	4.7k	1/8W	Carbon	AA
C1031	VCEAGA1AW476M	R	47	10V	Electrolytic	AA	R319	VRD-RA2BE822J	R	8.2k	1/8W	Carbon	AA
C1032	VCEAGA1CW106M	R	10	16V	Electrolytic	AA				(29H)	X5)
C1033	VCEAGA1EW227M	R	220	25V	Electrolytic	AC	R320	VRS-VV3AB100J	R	10	1W	Metal Oxic	e AA
C1034	VCEAGA1CW227M	R	220	16V	Electrolytic	AC	R321	VRD-RA2BE473J	R	47k	1/8W	Carbon	AA
C1601	VCFYFA1HA474J	R	0.47	50V	M. Polyester	AC	R322	VRD-RA2BE473J	R	47k	1/8W	Carbon	AA
C1602	VCQYTA1HM682J	R	6800p	50V	Mylar	AB	R323	VRD-RA2BE473J	R	47k	1/8W	Carbon	AA
C1603	VCEAGA1HW105M	R	1	50V	Electrolytic	AC	R324	VRD-RA2BE473J	R	47k	1/8W	Carbon	AA
C1604	VCEAGA1CW106M	R	10	.16V	Electrolytic	AA	R325	VRD-RA2BE103J	R	10k	1/8W	Carbon	AA
C1605	VCEAGA1CW106M	R	10	16V	Electrolytic	AA	R326	VRD-RA2BE100J	R	10	1/8W	Carbon	AA
C1606	VCKYD41CY103N	R	0.01	16V	Ceramic	AA	R327	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
C1607	VCKYD41CY103N	R	0.01	16V	Ceramic	AA	R328	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
C1608	VCEAGA1CW106M	R	10	16V	Electrolytic	AA	R329	VRD-RA2BE824J	R	820k	1/8W	Carbon	AA
C1609	VCKYD41CY103N	R	0.01	16V	Ceramic	AA	▲ R330	VRG-RF2EB100J	R	10	1/4W	Fuse Resis	tor AB
C1610	VCEAGA1CW476M	R	47	16V	Electrolytic	AB	R331	VRD-RA2BE102J	R	1k	1/8W	Carbon	AA
C1611	VCCSPA1HL221J	R	220p	50V	Ceramic	AA	R332	VRD-RA2BE102J	R	1k	1/8W	Carbon	AA
C1613	VCEAGA1CW476M	R	47	16V	Electrolytic	AB	R333	VRD-RA2BE152J	R	1.5k	1/8W	Carbon	AA
			(29H)	<5)			R334	VRD-RA2BE152J	R	1.5k	1/8W	Carbon	AA
C1614	VCEAGA1CW107M	R	100	16V	Electrolytic	AB	R335	VRD-RA2BE182J	R	1.8k	1/8W	Carbon	AA
			(29H)	<5)			R336	VRD-RA2BE182J	R	1.8k	1/8W	Carbon	AA
C1616	VCQYTA1HM473J	R	0.047	50V	Mylar	AA	R337	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
C1617	VCEAGA1HW225M	R	2.2	50V	Electrolytic	AB	R338	VRD-RA2BE2R2J	R	2.2	1/8W	Carbon	AA
C1618	VCQYTA1HM153J	R	0.015	50V	Mylar	AA	R339	VRD-RA2BE2R2J	R	2.2	1/8W	Carbon	AA
C1619	VCKYD41CY103N	R	0.01	16V	Ceramic	AA	R340	VRD-RM2HD332J	R	3.3k	1/2W	Carbon	AA
C1620	VCQYTA1HM104J	R	0.1	50V	Mylar	AA	R341	VRD-RA2BE683J	R	68k	1/8W	Carbon	AA
C1621	VCEAGA1CW337M	R	330	16V	Electrolytic	AC	R342	VRD-RA2BE563J	R	56k	1/8W	Carbon	AA
C1622	VCQYTA1HM103J	R	0.01	50V	Mylar	AA	R343	VRD-RA2BE473J	R	47k	1/8W	Carbon
C1623	VCQYTA1HM103J	R	0.01	50V	Mylar	AA	R344	VRD-RA2BE473J	R	47k	1/8W	Carbon	AA
C1624	VCEAGA1HW105M	R	1	50V	Electrolytic	AC	R345	VRD-RA2BE103J	К	10k	1/8W	Carbon	AA
C1625	VCEAGA1HW105M	R	1	50V	Electrolytic	AC	R346	VRD-RA2BE103J	К	10k	1/87	Carbon
C2801	VCCCPA1HH680J	R	68p	50V	Ceramic	AA	R347	VRD-RA2BE103J	К	10K	1/877	Carbon
C2802	VCEAGA1CW107M	К	100	16V	Electrolytic	AB	R348	VRD-RAZBE 153J	ĸ	15K	1/877	Carbon
C2803	VCKYPA1HF103Z	К	0.01	50V	Ceramic		R349		R D	16	1/877	Carbon
C2804	VCEAGA1CW226M	К	22	160	Electrolytic	AB	R350		п	4/K	1/877	Carbon	~~
C2808	VCEAGA1HW105M	к	1	500	Electrolytic	AC	R351		n D	47K	1/0 V V	Carbon
C2810	VCEAGATHW 105M	к	I	500	Electrolytic	AC	N302 R252		R	00K 16	1/011	Carbon
							R353	VRD-RA2BE3321	R	3.35	1/8\//	Carbon
	RES	19	TOR	-			R355	VRD-RA2BE3921	R	3.9k	1/8W	Carbon	AA
P201		B	11	ے 1/9\//	Carbon	ΔΔ	R356	VRD-RA2BE123	B	12k	1/8W	Carbon	AA
R301		R	11	1/0 VV	Carbon	ΔΔ	R357	VRD-RA2BE1233	B	10k	1/8W/	Carbon	AA
		R	56	1/8\//	Carbon	ΔΔ	B358	VRD-RA2BE123.1	R	12k	1/8W	Carbon	AA
P204		B	56	1/8\//	Carbon	ΔΔ	R359	VRD-RA2BE682.1	R	6.8k	1/8W	Carbon	AA
P205		B	20r	1/8\//	Carbon	ΔΔ	R360	VRD-RA2BE392.	R	3.9k	1/8W	Carbon	AA
R206	VRD-RA2BE3931	R	304	1/8W	Carbon	AA	R361	VRD-BA2BE392J	R	3.9k	1/8W	Carbon	AA
R207	VRD-RA2BE3321	R	3.34	1/8W	Carbon	AA	B362	VRD-BA2BE223J	R	22k	1/8W	Carbon	AA
B208	VRD-RA2BE3321	R	3.34	1/8W	Carbon	AA	R363	VRD-RA2BE223J	R	22k	1/8W	Carbon	AA
B300	VRD-RA2RF472.1	R	4.7k	1/8W	Carbon	AA	R364	VRD-RA2BE392.	R	3.9k	1/8W	Carbon	АА
R303	VRD-RA2RF472	R	4.7k	1/8W	Carbon	AA	R365	VRD-RA2BE123	R	12k	1/8W	Carbon	AA
R311	VRD-RA2BE223.	R	22k	1/8W	Carbon	AA	R366	VRD-RA2BE123J	R	12k	1/8W	Carbon	AA
R312	VRD-RA28F223.1	R	22k	1/8W	Carbon	AA	R367	VRD-RA2BE123J	R	12k	1/8W	Carbon	AA
R313	VRD-RA2EE105.1	B	1M	1/4W	Carbon	AA	R368	VRD-RA2BE562J	R	5.6k	1/8W	Carbon	AA
R314	VRD-RM2HD221J	R	220	1/2W	Carbon	AA	R369	VRD-RA2BE562J	R	5.6k	1/8W	Carbon	AA

Page 98

29HX	8
Ref. No.	F	Part No.		*	Desc	ription	Code	I	Ref. No.	Part No.	-	*	Desc	ription	Code
PW	B-A	DUNT	K	878	OWE				R485				1/014/
						•			R486	VRD-RA2BE223J	r F	1 ZZK	1/877	Carbon	AA
					Cont	inued)		_	R487	VRD-RA28E563.1	B	9.7K	1/01/	Carbon
		RESISTO	RS	(Cor	ntinue	d)						(29F	1/000	Carbon	АА
▲ R370	VRG-	RF2EB100J	R	10	1/4W	Fuse Resist	orAB		R488	VRD-RA2BE333J	8	33k	1/8W	Carbon	٨٨
R371	VRD-I	RA2EE2R2J	R	2.2	1/4W	Carbon	AA		R490	VRD-RA2BE682J	R	6.8k	1/8W	Carbon
R372	VRD-I	RA2EE2R2J	R	2.2	1/4W	Carbon	AA		R491	VRD-RA2BE822J	B	8.2k	1/8W	Carbon
R373	VRN-	VV3LBR22J	R	0.22	3W	Metal Film	AB		R492	VRD-RA2BE391J	R	390	1/8W	Carbon
R374	VRD-I	RA2BE473J	R	47k	1/8W	Carbon	AA		R493	VRD-RA2BE154J	R	150	( 1/8W	Carbon
R375	VRD-I	RM2HD332J	R	3.3K	( 1/2W	Carbon	AA		R494	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R376	VRD-I	RA2BE682J	R	6.8k	1/8W	Carbon	AA		R501	VRD-RA2BE332J	R	3.3k	1/8W	Carbon	AA
R377	VRD-I	RA2BE272J	R	2.7k	1/8W	Carbon	AA		R503	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R407	VRD-	RA2BE103J	R	10k	1/8W	Carbon	AA		R504	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R408	VRD-F	RA2BE103J	R	10k	1/8W	Carbon	AA		R506	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R409	VRD-F	RA2BE333J	R	33k	1/8W	Carbon	AA		R507	VRD-RA2BE102J	R	1k	1/8W	Carbon	AA
R410	VRD-I	RA2BE101J	R	100	1/8W	Carbon	AA		R508	VRD-RA2BE274J	R	270k	: 1/8W	Carbon	AA
R412	VRD-F	RA2EE471J	R	470	1/4W	Carbon	AA		R510	VRD-RA2BE124J	R	120k	: 1/8W	Carbon	AA
R413	VRD-F	RA2BE101J	R	100	1/8W	Carbon	AA		R511	VRD-RA2BE683J	R	68k	1/8W	Carbon	AA
R415	VRD-F	RA2BE101J	R	100	1/8W	Carbon	AA		R512	VRD-RA2BE223J	R	22k	1/8W	Carbon	AA
R416	VRD-H	A2BE392J	R	3.9k	1/8W	Carbon	AA		R514	VRD-RM2HD2R7J	R	2.7	1/2W	Carbon	AA
R417	VRD-F	A2EE4/1J	К	470	1/4W	Carbon	AA		R515	VRD-RM2HD2R7J	R	2.7	1/2W	Carbon	AA
R418 R410			К	100	1/8W	Carbon	AA		R516	VRD-RM2HD2R7J	R	2.7	1/2W	Carbon	AA
R419			R	100	1/87	Carbon	AA		R517	VRD-RM2HD391J	R	390	1/2W	Carbon	AA
R420			R D	3.3K	1/87	Carbon	AA		R519	VRD-RA2EE123J	R	12k	1/4W	Carbon	AA
R421		A2DEZ/JJ	n D	278	1/877	Carbon			R520	VRD-RM2HD181J	R	180	1/2W	Carbon	AA
R422	VRD-F	A28E394J	R	2006	1/0VV	Carbon			R521	VRD-RA2BE223J	R	22k	1/8W	Carbon	AA
R423	VRD-F	A2EE105 I	R	390K	1/000	Carbon			R522	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R425	VRD-F	Δ28E6821	R	6.84	1/4VV 1/Q\A/	Carbon		٨	R523	VRD-RA2BE222J	R	2.2k	1/8W	Carbon	AA
R427	VRD-F	A28F223.1	R	22k	1/8\//	Carbon	~~	2:5	NOZO REDE		R	22	1/47	Fuse Resi	stor AB
R428	VRD-F	A2BE154J	R	150k	1/8W	Carbon	ΔΔ		R520		R D	180	1/200	Carbon	AA
R429	VRD-F	A2BE392J	R	3.9k	1/8W	Carbon	ΔΔ		R529		n D	4 7 14	1/877	Carbon
R430	VRD-F	A2BE222J	R	2.2k	1/8W	Carbon			R815	VRD-RA2RE101	n g	4.710	1/41	Carbon	AA
R450	VRD-F	M2HD471J	R	470	1/2W	Carbon	AA		R816	VRD-RA2BE101J	R	100	1/01/	Carbon
R451	VRD-R	A2BE101J	R	100	1/8W	Carbon	AA		R817	VRD-RA2BE332J	R	3 3k	1/8\//	Carbon
R457	VRD-R	M2HD271J	R	270	1/2W	Carbon	AA		R818	VRD-RA2BE102J	В	1k	1/8\//	Carbon	ΔΔ
R461	VRD-R	A2BE103J	R	10k	1/8W	Carbon	AA		R819	VRD-RA2BE221J	R	220	1/8W	Carbon	ΔΔ
R462	VRD-R	A2BE103J	R	10k	1/8W	Carbon	AA		R820	VRD-RA2BE104J	R	100k	1/8W	Carbon	ΑΑ
R463	VRD-R	A2BE101J	R	100	1/8W	Carbon	AA		R823	VRD-RA2BE122J	R	1.2k	1/8W	Carbon	AA
R465	VRD-R	A2BE101J	R	100	1/8W	Carbon	AA		R825	VRD-RA2BE821J	R	820	1/8W	Carbon	AA
R466	VRD-R	A2BE101J	R	100	1/8W	Carbon	AA		R826	VRD-RA2BE222J	R	2.2k	1/8W	Carbon	AA
R467	VRD-R	A2BE101J	R	100	1/8W	Carbon	AA		R830	VRD-RA2BE102J	R	1k	1/8W	Carbon	AA
R468	VRD-R	A2BE562J	R	5.6k	1/8W	Carbon	AA		R833	VRD-RA2BE221J	R	220	1/8W	Carbon	AA
R469	VRD-R	A2BE102J	R	1k	1/8W	Carbon	AA		R834	VRD-RA2BE221J	R	220	1/8W	Carbon	AA
R470	VRD-R	A2BE101J	R	100	1/8W	Carbon	AA		R835	VRD-RA2BE221J	R	220	1/8W	Carbon	AA
R471	VRD-R	A2BE473J	R	47k	1/8W	Carbon	AA		R836	VRD-RA2BE473J	R	47k	1/8W	Carbon	AA
R472	VRD-R	A2BE472J	R	4.7k	1/8W	Carbon	AA		R837	VRD-RA2BE473J	R	47k	1/8W	Carbon	AA
R474	VRD-R	A2BE392J	R	3.9k	1/8W	Carbon	AA		R838	VRD-RA2BE222J	R	2.2k	1/8W	Carbon	AA
R475	VRD-R	A2BE562J	R	5.6k	1/8W	Carbon	AA		R846	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R476	VRD-R	A2BE224J	R	220k	1/8W	Carbon	AA		R847	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R477	VRD-R	A2BE274J	R	270k	1/8W	Carbon	AA		R848	VRD-RA2BE392J	R	3.9k	1/8W	Carbon	AA
K478	VRD-R	AZEE471J	R	470	1/4W	Carbon	AA		R901	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R479	VRD-R	A2BE472J	R	4.7k	1/8W	Carbon	AA		R902	VRD-RA2BE182J	R	1.8k	1/8W	Carbon	AA
K480	VKD-R	A2BE222J	К	2.2k	1/8W	Carbon	AA		R903	VRD-RA2BE222J	R	2.2k	1/8W	Carbon	AA
R481	VRD-R	AZBEZ/3J	н	27K	1/8W	Carbon	AA		R906	VRD-RA2EE475J	R	4.7M	1/4W	Carbon	AA
N482	vnD-R	HZBEZZJJ	н	ZZK	1/877	Carbon	AA		R1001	VKD-KA2BE102J	R	1k	1/8W	Carbon	AA

29HX5

Page 99

Ref. No.	Part No.	*		Descr	iption	Code	Ref. No.	Part No.	*		Descri	ption C	ode
PWE	B-A DUNT	^- K8	780	WE	V1/V0		R1056	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
							R1057	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
			II (C	JONTI	nuea)		R1058	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
	RESISTO	RS (	(Con	tinued	1) (E		R1060	VRD-RA2BE103J	R	10k	1/8W	Carbon	AA
R1002	VRD-RA2BE562J	R	5.6k	1/8W	Carbon	AA	R1061	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R1003	VRD-RA2BE103J	R	10k	1/8W	Carbon	AA	R1062	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R1004	VRD-RA2BE562J	R	5.6k	1/8W	Carbon	AA	R1063	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R1005	VRD-RA2BE103J	R	10k	1/8W	Carbon	AA	R1064	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R1006	VRD-RA2BE103J	R	10k	1/8W	Carbon	AA	R1065	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R1007	VRD-RA2BE563J	R	56k	1/8W	Carbon	AA	R1066	VRD-RA2BE102J	R	1k	1/8W	Carbon	AA
R1008	VRD-RA2BE563J	R	56k	1/8W	Carbon	AA	R1067	VRD-RA2BE472J	R	4.7k	1/8W	Carbon	AA
R1009	VRD-RA2BE101J	R	100	1/8W	Carbon	AA	R1068	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R1010	VRD-RA2BE101J	R	100	1/8W	Carbon	AA	R1069	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R1011	VRD-RA2BE101J	R	100	1/8W	Carbon	AA	R1070	VRD-RA2BE682J	R	6.8k	1/8W	Carbon	AA
R1012	VRD-RA2BE472J	R	4.7k	1/8W	Carbon	AA	R1071	VRD-RA2BE103J	R	10k	1/8W	Carbon	AA
R1013	VRD-RA2BE472J	R	4.7k	1/8W	Carbon	AA	R1072	VRD-RA2BE223J	R	22k	1/8W	Carbon	AA
R1014	VRD-RA2BE472J	R	4.7k	1/8W	Carbon	AA	R1073	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R1015	VRD-RA2BE472J	R	4.7k	1/8W	Carbon	AA	R1074	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R1016	VRD-RA2BE472J	R	4.7k	1/8W	Carbon	AA	R1075	VRD-RA2BE392J	R	3.9k	1/8W	Carbon	AA
R1018	VRD-RA2BE683J	R	68k	1/8W	Carbon	AA	R1076	VRD-RA2BE272J	R	2.7k	1/8W	Carbon	AA
R1020	VRD-RA2BE683J	R	68k	1/8W	Carbon	AA				(29H	X5)
R1022	VRD-RA2BE563J	R	56k	1/8W	Carbon	AA	R1076	VRD-RA2BE392J	R	3.9k	1/8W	Carbon	AA
			(29H	X8)						(29H	X8)
R1023	VRD-RA2BE563J	R	56k	1/8W	Carbon	AA	R1077	VRD-RA2BE103J	R	10k	1/8W	Carbon	AA
			(29H	X8)			R1078	VRD-RA2BE103J	R	10k	1/8W	Carbon	AA
R1024	VRD-RA2BE472J	R	4.7k	1/8W	Carbon	AA	R1079	VRD-RA2BE103J	R	10k	1/8W	Carbon	AA
R1025	VRD-RA2BE472J	R	4.7k	1/8W	Carbon	AA	R1080	VRD-RA2BE103J	R	10k	1/8W	Carbon	AA
R1026	VRD-RA2BE472J	R	4.7k	.1/8W	Carbon	AA	R1081	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R1027	VRD-RA2BE472J	R	4.7k	1/8W	Carbon	AA	R1082	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R1028	VRD-RA2BE472J	R	4.7k	1/8W	Carbon	AA	R1083	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R1029	VRD-RA2BE472J	R	4.7k	1/8W	Carbon	AA	R1084	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R1030	VRD-RA2BE472J	R	4.7k	1/8W	Carbon	AA	R1085	VRD-RA2BE333J	R	33k	1/8W	Carbon	AA
R1031	VRD-RA2BE101J	R	100	1/8W	Carbon	AA	R1090	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R1032	VRD-RA2BE123J	R	12k	1/8W	Carbon	AA	R1091	VRD-RA2BE222J	R	2.2k	1/8W	Carbon	AA
R1033	VRD-RA2BE472J	R	4.7k	1/8W	Carbon	AA	R1092	VRD-RA2BE103J	R	10k	1/8W	Carbon	AA
R1035	VRD-RA2BE332J	R	3.3k	1/8W	Carbon	AA	R1093	VRD-RA2BE103J	R	10k	1/8W	Carbon	AA
R1036	VRD-RA2BE332J	R	3.3k	1/8W	Carbon	AA	R1094	VRD-RA2BE681J	R	680	1/8W	Carbon	AA
R1037	VRD-RA2BE332J	R	3.3k	1/8W	Carbon	AA	R1095	VRD-RA2BE103J	R	10k	1/8W	Carbon	AA
R1038	VRD-RA2BE472J	R	4.7k	1/8W	Carbon	AA	R1096	VRD-RA2BE473J	R	47k	1/8W	Carbon	AA
R1039	VRD-RA2BE472J	R	4.7k	1/8W	Carbon	AA	R1097	VRD-RA2BE473J	R	47k	1/8W	Carbon	AA
R1040	VRD-RA2BE103J	R	10k	1/8W	Carbon	AA	R1099	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R1041	VRD-RA2BE333J	R	33k	1/8W	Carbon	AA	R1201	VRD-RA2BE222J	R	2.2k	1/8W	Carbon	AA
R1042	VRD-RA2BE103J	R	10k	1/8W	Carbon	AA	R1202	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R1043	VRD-RA2BE562J	R	5.6k	1/8W	Carbon	AA	R1203	VRD-RA2BE473J	R	47k	1/8W	Carbon	AA
R1044	VRD-RA2BE333J	R	33k	1/8W	Carbon	AA	R1204	VRD-RA2BE473J	R	47k	1/8W	Carbon	AA
R1045	VRD-RA2BE102J	R	1k	1/8W	Carbon	AA	R1205	VRD-RA2BE103J	R	10k	1/8W	Carbon	AA
R1046	VRD-RA2BE102J	R	1k	1/8W	Carbon	AA	R1206	VRS-VV3DB150J	R	15	2W	Metal Oxide	AA
R1047	VRD-RA2BE223J	R	22k	1/8W	Carbon	AA	R1207	VRD-RA2BE562J	R	5.6k	1/8W	Carbon	AA
R1048	VRD-RA2BE102J	R	1k	1/8W	Carbon	AA	R1208	VRD-RM2HD390J	R	39	1/2W	Carbon	AA
R1049	VRD-RA2BE333J	R	33k	1/8W	Carbon	AA	R1209	VRN-VV3DB3R9J	R	3.9	2W	Metal Film	AB
R1050	VRD-RA2BE102J	R	1k	1/8W	Carbon	AA	R1210	VRD-RA2BE153J	R	15k	1/8W	Carbon	AA
R1051	VRD-RA2BE333J	R	33k	1/8W	Carbon	AA	R1211	VRD-RA2BE153J	R	15k	1/8W	Carbon	AA
R1052	VRD-RA2BE102J	R	1k	1/8W	Carbon	AA	R1212	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R1053	VRD-RĄ2BE222J	R	2.2k	1/8W	Carbon	AA	R1213	VRD-RA2BE101J	R	100	1/8W	Carbon	AA
R1054	VRD-RA2BE103J	R	10k	1/8W	Carbon	AA	R1214	VRD-RA2BE103J	R	10 k	1/8W	Carbon	AA
R1055	VRD-RA2BE273J	R	27k	1/8W	Carbon	AA	R1215	VRD-RA2BE223J	R	22k	1/8W	Carbon	AA

Page 100

Part No. Pascription Cade PWB-A DUNTKS780WEV1/V0 MAIN UNIT (Continued) R1270 MD-RA28E323 (2000) R 331 NBW Carbon AA R1267 VPD-RA28E1323 (2000) R 101 ND-RA28E333 (2000) R 331 NBW Carbon AA R1267 VPD-RA28E1323 (2000) R 101 ND-RA28E1324 (2000) R 331 NBW Carbon AA R1267 VPD-RA28E1323 (2000) R 101 ND-RA28E1324 (2000) R 101 ND-RA28E1324 (2000) R 104 ND-RA28E1324 (2000) R 104 ND-RA28E1324 (2000) R 104 ND-RA28E1324 (2000) R 104 ND-RA28E1324 (2000) R 104 ND-RA28E1324 (2000) R 104 ND-RA28E1324 (2000) R 104 ND-RA28E1324 (2000) R 104 ND-RA28E1324 (2000) R 104 ND-RA28E1324 (2000) R 104 ND-RA28E1324 (2000) R 104 ND-RA28E1324 (2000) R 104 ND-RA28E1324 (2000) R 104 ND-RA28E1324 (2000) R 104 ND-RA28E1324 (2000) R 104 ND-RA28E1324 (2000) R 104 ND-RA28E1324 (2000) R 104 ND-RA28E1324 (2000)	29HX 29HX	5 8
PWB-A DUNTKS780WEV1/V0 MAIN UNIT (Continued) R127 VRD RA28E333 R127 R 38 1/8W Carbon AA RESISTORS (Continued) R1216 VRD RA28E333 R1216 R33 1/8W Carbon AA R1216 VRD RA28E133 R1216 R1A R184 R34 1/8W Carbon AA R1216 VRD RA28E133 R1216 R1A R187 VRD RA28E133 R184	Ref. No.	Ра	irt No.		*	Descr	iption	Code	Ref. No.	Part No.		*	Desc	ription	Code
MAIN UNIT (Continued) R321 VBC RAZEE331 R33 NBW Carbon AA R1216 VBC RAZEE102J R 10k 189V Carbon AA R127 VBC RAZEE331 R 33k 108V Carbon AA R1216 VBC RAZEE102J R 10k 189V Carbon AA R127 VBC RAZEE123 R 128 VBC RAZEE102J R 10k 189V Carbon AA R1219 VBC RAZEE102J R 1k 189V Carbon AA R100 VBC RAZEE123 R 124 VBC RAZEE123 R 124 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124 R 120 VBC RAZEE124	PW	B-A	DUNT	K	878	OWE	V1/V0		R1270	VRD-RA2BE333J	F	3 336	1/8\\/	Carbon
FESISTORS (Continued) FILIT VPD-RADES33 R 38 19W Carbon Aa R1217 VPD-RADES33 R 38 19W Carbon AA R1217 VPD-RADES33 R 38 19W Carbon AA R1219 VPD-RADES133 R 38 119W Carbon AA R1219 VPD-RADES123 R 138 119W Carbon AA R1219 VPD-RADES123 R 138 119W Carbon AA R1220 VPD-RADES123 R 122 118W Carbon AA R1221 VPD-RADES123 R 122 118W Carbon AA R1221 VPD-RADES123 R 124 118W Carbon AA R1224 VPD-RADES133 R 100 118W Carbon AA R1224 VPD-RADES133 R 100 118W Carbon AA R1224 VPD-RADES133 R 100 118W Carbon AA R1224 VPD-RADES133 R 104 18W Carbon AA R1224 VPD-RADES133 R 138 118W Carbon AA				JN	IT (	Conti	nued)		R1271	VRD-RA2BE333J	F	33k	1/8W	Carbon
HE126 VID-RAZEE103J R 328.189V Carbon AA R1126 VID-RAZEE102J R 11k 18W Carbon AA R101 VID-RAZEE122J R 1204.189V Carbon AA R1219 VID-RAZEE102J R 11k 18W Carbon AA R1001 VID-RAZEE122J R 1204.189V Carbon AA R1219 VID-RAZEE102J R 1k 18W Carbon AA R1001 VID-RAZEE122J R 1204.189V Carbon AA R1229 VID-RAZEE102J R 100 18W Carbon AA R1005 VID-RAZEE122J R 2124.189V Carbon AA R1229 VID-RAZEE102J R 658.178V Carbon AA R1069 VID-RAZEE123J R 2204.144V Carbon AA R1229 VID-RAZEE103J R 10k 18W Carbon AA R1109 VID-RAZEE123J R 328.169V Carbon AA R1229 VID-RAZEE123J R 10k 18W Carbon AA R1109 VID-							nucu)		R1272	VRD-RA2BE333J	F	33k 3	1/8W	Carbon	AA
N1121 VID-RAZEE102J R 10K 120V Carbon AA P121V VID-RAZEE123J R 12M VIAV Carbon AA R1219 VID-RAZEE123J R 12M 14W Carbon AA R1022 VID-RAZEE123J R 12M VID AA R1020 VID-RAZEE123J R 12M VID AA R1219 VID-RAZEE123J R 110 13W Carbon AA R1060 VID-RAZEE123J R 12X 13W Carbon AA R1224 VID-RAZEE103J R 100 13W Carbon AA R1060 VID-RAZEE123J R 12X 13W Carbon AA R1224 VID-RAZEE103J R 10K 18W Carbon AA R1060 SEe Controls A R107 VID-RAZEE103J R 10K 18W Carbon AA R1224 VID-RAZEE103J R 10K 18W Carbon AA R108 MRD-RAZEE103J R 10K 18W Carbon AA R1224 VID-RAZEE103J	B1010		RESISTOR	เร		ntinue	d)		R1273	VRD-RA2BE333J	F	33k 3	1/8W	Carbon	AA
R128 VDRAZEES33 R 128 VMRAZES33 R 108 128 VMRAZES33 R 108 128 VMRAZES33 R 108 128 VMRAZES33 R 108 128 VMRAZES33 R 108 128 VMRAZES33 R 108 128 VMRAZES33 R 108 128 108 128	R1210			R	10K	1/8W	Carbon		R1274	VRD-RA2BE683J	F	3 68k	1/8W	Carbon	AA
H1219 WID_RA2BE 102,J R 1k 1980 Carbon AA R1002 WID_RA2BE 102,J R 12k WID_CAUSE 123,J R 12k WID_CAUSE 123,J R 12k WID_CAUSE 123,J R 12k WID_CAUSE 123,J R 12k WID_CAUSE 123,J R 12k WID_CAUSE 123,J R 12k WID_CAUSE 123,J R 12k WID_CAUSE 123,J R 12k WID_CAUSE 123,J R 22k WID_CAUSE 123,J R 22k WID_CAUSE 123,J R 23k WID_CAUSE 123,J R 10k WID WID_CAUSE 123,J R 10k WID AA R122k VID_CAUSE 123,J R 10k 18W Carbon AA R1605 WID-CAUSE 103,J R 10k 18W Carbon AA R1604 WID-CAUSE 103,J R 10k 18W Carbon AA R1615 WID-CAUSE 103,J R 10k 18W Carbon AA R122k VID-RAUSE 103,J R 10k 18W Carbon AA R1615 WID-CAUSE 103,J R 10k 18W Carbon AA R122k VID-RAUSE 103,J R 10k 18W	R1217	VRD-R/	A2BE333.1	R	33F 1K	1/8\//	Carbon		R1601	VRD-RA2EE125J	F	1.2	/1/4W	Carbon	AA
R1220 VRD-RA2BE102J R 11k 11km Carbon AA R1030 VRD-RA2BE12J R 12k 12W Carbon AA R1221 VRD-RA2BE162J R 10k 18W Carbon AA R1055 VRD-RA2BE12J R 12k 18W Carbon AA R1221 VRD-RA2BE162J R 63k 18W Carbon AA R1067 VRD-RA2BE162J R 22k 18W Carbon AA R1222 VRD-RA2BE103J R 10k 18W Carbon AA R1067 VRD-RA2BE103J R 10k 18W Carbon AA R1067 VRD-RA2BE103J R 10k 18W Carbon AA R1017 VRD-RA2BE103J R 10k 18W Carbon AA R1012 VRD-RA2BE103J R 10k 18W Carbon AA R1014 VRD-RA2BE103J R 10k 18W Carbon AA R1014 VRD-RA2BE103J R 10k 18W Carbon AA R1224 VRD-RA2BE103J R 10k 18W Carb	R1219	VRD-R/	A2BE102J	R	1k	1/8W	Carbon		R1602		1	120	k 1/8W	Carbon	AA
P1221 VRD-RA2BE101J R 100 VRD-RA2BE124J R 68 k 18W Carbon AA R1222 VRD-RA2BE682J R 68 k 18W Carbon AA R100 VRD-RA2BE223J R 28k 174W Carbon AA R1224 VRD-RA2BE682J R 68 k 18W Carbon AA R100 VRD-RA2BE273J R 29k 174W Carbon AA R1225 VRD-RA2BE103J R 10k 18W Carbon AA R160 VRD-RA2BE103J R 10k 18W Carbon AA R1226 VRD-RA2BE103J R 10k 18W Carbon AA R1610 VRD-RA2BE103J R 10k 18W Carbon AA R1224 VRD-RA2BE103J R 10k 18W Carbon AA R1614 VRD-RA2BE13J R 10k 18W Carbon AA R1230 VRD-RA2BE3J R 3.8 18W Carbon AA R1614 VRD-RA2BE13J R 10k 18W Carbon AA R1234 VRD-RA2BE163J R 3.8 18W Carbon AA R1615 VRD-RA2BE103J R 10k 18W Carbon<	R1220	VRD-R/	A2BE102J	R	1k	1/8W	Carbon	AA	R1604	VRD-RA2BE1231	F	\ 120 } 12k	K 1/8VV	Carbon	AA
H1222 VPD-RA2BE682.J R 6.8. H3W Carbon AA R1606 VPD-RA2E62.J R 22x H3W Carbon AA R1224 VPD-RA2E612.J R 6.8. H3W Carbon AA R1607 VPD-RA2E613.J R 10x Carbon AA R1225 VPD-RA2E6103.J R 10x H3W Carbon AA R1610 VPD-RA2E613.J R 10x H3W Carbon AA R1226 VPD-RA2E613.J R 10x H3W Carbon AA R1611 VPD-RA2E613.J R 10x H3W Carbon AA R1220 VPD-RA2E613.J R 10x H3W Carbon AA R1612 VPD-RA2E613.J R 10x H3W Carbon AA R1231 VPD-RA2E613.J R 3.3x H3W Carbon AA R1616 VPD-RA2E613.J R 10x H3W Carbon AA R1613 VPD-RA2E613.J<	R1221	VRD-R	A2BE101J	R	100	1/8W	Carbon	AA	R1605	VRD-RA2BE124J	F	120	1/8W	Carbon
R122 VRD-RA2EE602J R 6.58 / 1/8W Carbon AA R1607 VRD-RA2EE124J R 200 / 1/8W Carbon AA R1225 VRD-RA2EE103J R 10k / 1/8W Carbon AA R1608 WRD-RA2EE103J R 10k / 1/8W Carbon AA R1225 VRD-RA2EE103J R 10k / 1/8W Carbon AA R1610 WRD-RA2EE13J R 10k / 1/8W Carbon AA R1227 VRD-RA2EE103J R 10k / 1/8W Carbon AA R1611 WRD-RA2EE103J R 56k / 1/4W Carbon AA R1229 VRD-RA2EE133J R 10k / 1/8W Carbon AA R1615 WRD-RA2EE133J R 10k / 1/8W Carbon AA R1230 VRD-RA2EE332J R 3.3k 1/8W Carbon AA R1616 WRD-RA2EE103J R 10k 1/8W Carbon AA R1231 VRD-RA2EE532J R 3.3k 1/8W Carbon AA R1616 WRD-RA2EE103J R 10k 1/8W Carbon AA R1231 VRD-RA2EE533J R 3.3k 1/8W Carbon AA R1616 WRD-RA2EE103J R 10k 1/8W Carbon AA	R1222	VRD-R/	42BE682J	R	6.8k	1/8W	Carbon	AA	R1606	VRD-RA2BE223J	F	22k	1/8W	Carbon
H1224 VRD-RAZEE10J R 100 18W Carbon AA R1608 VRD-RAZEE103J R 10k 18W Carbon AA R1225 VRD-RAZEE103J R 10k 18W Carbon AA R1610 VRD-RAZEE103J R 10k 18W Carbon AA R1225 VRD-RAZEE103J R 10k 18W Carbon AA R1611 VRD-RAZEE103J R 10k 18W Carbon AA R1225 VRD-RAZEE152J R 15k 17W Carbon AA R1615 VRD-RAZEE103J R 10k 18W Carbon AA R1235 VRD-RAZEE523J R 33k 18W Carbon AA R1616 VRD-RAZEE103J R 10k 18W Carbon AA R1235 VRD-RAZEE503J R 35k 18W Carbon AA R1616 VRD-RAZEE103J R 10k 18W Carbon AA R1	R1223	VRD-R/	42BE682J	R	6.8k	1/8W	Carbon	AA	R1607	VRD-RA2EE824J	F	820	k 1/4W	Carbon	AA
H122b VHD-HA2BE103J R 10k 1/8W Carbon AA R1609 See Controls R122c VRD-HA2BE103J R 10k 1/8W Carbon AA R1611 VRD-RA2BE153J R 10k 1/8W Carbon AA R122v VRD-RA2BE103J R 10k 1/8W Carbon AA R1611 VRD-RA2BE13J R 13k 1/8W Carbon AA R123v VRD-RA2BE132J R 3.k 1/8W Carbon AA R1614 VRD-RA2BE103J R 10k 1/8W Carbon AA R123v VRD-RA2BE332J R 3.k 1/8W Carbon AA R1616 VRD-RA2BE103J R 10k 1/8W Carbon AA R123v VRD-RA2BE103J R 16k 1/8W Carbon AA R1616 VRD-RA2BE103J R 10k 1/8W Carbon AA R123v VRD-RA2BE103J R 16k 1/8	R1224	VRD-RA	42BE101J	R	100	1/8W	Carbon	AA	R1608	VRD-RA2EE274J	F	270	k 1/4W	Carbon	AA
n122 VRD-RAZEE103J R 10k 1/8W Carbon AA R1610 VRD-RAZEE103J R 10k 1/8W Carbon AA R122 VRD-RAZEE103J R 10k 1/8W Carbon AA R1611 VRD-RAZEE103J R 10k 1/8W Carbon AA R1230 VRD-RAZEE103J R 10k 1/8W Carbon AA R1611 VRD-RAZEE103J R 10k 1/8W Carbon AA R1230 VRD-RAZEE103J R 3.8 1/8W Carbon AA R1615 VRD-RAZEE103J R 10k 1/8W Carbon AA R1230 VRD-RAZEE523J R 3.8 1/8W Carbon AA R1617 VRD-RAZEE103J R 10k 1/8W Carbon AA R1230 VRD-RAZEE503J R 10k 1/8W Carbon AA R1617 VRD-RAZEE103J R 10k 1/8W Carbon AA R1230 VRD-RAZEE103J R 10k 1/8W Carbon AA R1627 VRD-RAZEE103J R 10k 1/8W	R1225	VRD-RA	A2BE103J	R	10k	1/8W	Carbon	AA	R1609	See Controls
h122 VRD-FA2BE 103.3 F1 10K 12W Carbon AA R1611 VRD-R42EE153.4 R 15k 1/8W Carbon AA R1230 VRD-FA2BE152.3 R 3.5k 1/8W Carbon AA R1613 VRD-R42EE33.4 R 33k 1/8W Carbon AA R1230 VRD-R42BE332.2 R 3.3k 1/8W Carbon AA R1615 VRD-R42BE103.3 R 10k 1/8W Carbon AA R1233 VRD-R42BE332.1 R 3.3k 1/8W Carbon AA R1615 VRD-R42BE103.3 R 10k 1/8W Carbon AA R1233 VRD-R42BE533.3 R 10k 1/8W Carbon AA R1615 VRD-R42BE103.3 R 10k 1/8W Carbon AA R1230 VRD-R42BE103.3 R 10k 1/8W Carbon AA R1616 VRD-R42BE103.3 R 10k 1/8W Carbon AA R1230 VRD-R42BE103.3 R 10k 1/8W Carbon AA R1612 VRD-R42BE103	R1226		A2BE103J	R	10k	1/8W	Carbon	AA	R1610	VRD-RA2BE103J	F	10k	1/8W	Carbon	AA
Integr WID-RAZEE 532, R 15.K WW Carbon AA R1613 VRD-RAZEE 533, R Rot N/RW Carbon AA R1230 VRD-RAZEE 533, R 3.3k N/RW Carbon AA R1614 VRD-RAZEE 103, R 10k 1/RW Carbon AA R1231 VRD-RAZEE 533, R 3.3k 1/RW Carbon AA R1615 VRD-RAZEE 103, R 10k 1/RW Carbon AA R1234 VRD-RAZEE 103, R 5.6k 1/RW Carbon AA R1616 VRD-RAZEE 103, R 10k 1/RW Carbon AA R1235 VRD-RAZEE 103, R 10k 1/RW Carbon AA R1620 VRD-RAZEE 102, R 1k 1/RW Carbon AA R1235 VRD-RAZEE 103, R 10k 1/RW Carbon AA R1620 VRD-RAZEE 102, R 1k 1/RW Carbon AA	R1227		AZBE 103J	к	10K	1/8W	Carbon	AA	R1611	VRD-RA2BE153J	F	15k	1/8W	Carbon	AA
H1230 VRD-RA2BE132J R 33k 1/8W Carbon AA R1614 VRD-RA2BE103J R 10k 1/8W Carbon AA R1231 VRD-RA2BE133J R 33k 1/8W Carbon AA R1614 VRD-RA2BE103J R 10k 1/8W Carbon AA R1232 VRD-RA2BE133J R 33k 1/8W Carbon AA R1615 VRD-RA2BE103J R 10k 1/8W Carbon AA R1233 VRD-RA2BE103J R 10k 1/8W Carbon AA R1619 VRD-RA2BE103J R 10k 1/8W Carbon AA R1235 VRD-RA2BE103J R 10k 1/8W Carbon AA R1619 VRD-RA2BE103J R 1/k 1/8W Carbon AA R162 VRD-RA2BE103J R 1/k 1/8W Carbon AA R162 VRD-RA2BE103J R 1/k 1/8W Carbon AA R162 VRD-RA2	R1220	VRD-RA	A2BE1035	R	154	1/0VV 1/8\//	Carbon		R1612	VRD-RA2EE564J	F	560	k 1/4W	Carbon	AA
R1231 VRD-RA2BE332 R 3.3k 1/8W Carbon AA R1615 VRD-RA2BE103. R 10k 1/8W Carbon AA R1232 VRD-RA2BE332. R 3.3k 1/8W Carbon AA R1615 VRD-RA2BE103. R 10k 1/8W Carbon AA R1233 VRD-RA2BE503. R 33k 1/8W Carbon AA R1615 VRD-RA2BE103. R 10k 1/8W Carbon AA R1236 VRD-RA2BE502. R 5.6k 1/8W Carbon AA R1619 VRD-RA2BE102. R 12.4 VRD-RA2BE102. R 14k 1/8W Carbon AA R1236 VRD-RA2BE502. R 12.4 VRD-RA2BE102. R 14k 1/8W Carbon AA R162 VRD-RA2BE102. R 14k 1/8W Carbon AA R1240 VRD-RA2BE102.J R 14k 1/8W Carbon AA R162 VRD-RA2BE102.J R 14k 1/8W Carbon AA R1240 VRD-RA2BE102.J R 14k 1/8W Carbon AA R162 VRD-RA2BE102.J R 14k 1/8W Carbon AA R1241	R1230	VRD-RA	42BE332J	R	3.3k	1/8W	Carbon		R1614		1	330	k 1/4W	Carbon	AA
R1232 VRD-RA28E332J R 3.3k 1/8W Carbon AA R1616 VRD-RA28E103J R 10W Carbon AA R1233 VRD-RA28E103J R 3.3k 1/8W Carbon AA R1617 VRD-RA28E103J R 10k 1/8W Carbon AA R1234 VRD-RA28E103J R 10k 1/8W Carbon AA R1618 VRD-RA28E103J R 10k 1/8W Carbon AA R1235 VRD-RA28E103J R 10k 1/8W Carbon AA R1620 VRD-RA28E102J R 1.k 1/8W Carbon AA R1237 VRD-RA28E103J R 6.k 1/8W Carbon AA R1622 VRD-RA28E102J R 1.k 1/8W Carbon AA R1240 VRD-RA28E103J R 1.k 1/8W Carbon AA R1625 VRD-RA28E103J R 1.k 1/8W Carbon AA R1244 VRD-RA28E103J R 100 1/8W Carbon AA R1625	R1231	VRD-RA	A2BE332J	R	3.3k	1/8W	Carbon	AA	B1615	VRD-RA2BE103J	n B	10k	1/877	Carbon	AA
R1233 VRD-RA2BE133J R 33k 1/8W Carbon AA R1617 VRD-RA2BE103J R 10k 1/8W Carbon AA R1234 VRD-RA2BE103J R 10k 1/8W Carbon AA R1619 VRD-RA2BE103J R 10k 1/8W Carbon AA R1235 VRD-RA2BE103J R 10k 1/8W Carbon AA R1619 VRD-RA2BE103J R 10k 1/8W Carbon AA R1235 VRD-RA2BE103J R 6k 1/8W Carbon AA R1621 VRD-RA2BE33J R 38k 1/8W Carbon AA R1235 VRD-RA2BE103J R 6k 1/8W Carbon AA R1622 VRD-RA2BE13J R 3k 1/8W Carbon AA R1241 VRD-RA2BE101J R 100 1/8W Carbon AA R1625 VRD-RA2BE101J R 100 1/8W Carbon AA R1241 VRD-RA2BE101J R 100 1/8W Carbon AA R1625 VRD-RA2BE101J R 100 1/8W Carbon AA R1244 VRD-RA2BE101J R 1	R1232	VRD-RA	42BE332J	R	3.3k	1/8W	Carbon	AA	R1616	VRD-RA2BE103J	R	10k	1/8W	Carbon
R1234 VRD-RA2BE103J R 5.6k 1/8W Carbon AA R1618 VRD-RA2BE103J R 10k 1/8W Carbon AA R1235 VRD-RA2BE103J R 10k 1/8W Carbon AA R1619 VRD-RA2BE102J R 1k 1/8W Carbon AA R1237 VRD-RA2BE103J R 10k 1/8W Carbon AA R1621 VRD-RA2BE102J R 1k 1/8W Carbon AA R1238 VRD-RA2BE103J R 16k 1/8W Carbon AA R1622 VRD-RA2BE102J R 1k 1/8W Carbon AA R1239 VRD-RA2BE102J R 1k 1/8W Carbon AA R1622 VRD-RA2BE103J R 100 AA R1240 VRD-RA2BE101J R 100 1/8W Carbon AA R1625 VRD-RA2BE102J R 1k 1/8W Carbon AA R1242 VRD-RA2BE101J R 100 1/8W Carbon AA R1625 VRD-RA2BE102J R 1k 1/8W Carbon AA R1244 VRD-RA2BE101J R 100 1/8W Carbon AA R1625 VRD-RA2BE102J R 1k 1/8W Carbon AA	R1233	VRD-RA	\2BE333J	R	33k	1/8W	Carbon	AA	R1617	VRD-RA2BE103J	R	10k	1/8W	Carbon
R1235 VRD-RA2BE103J R IN I/8W Carbon AA R1619 VRD-RA2BE102J R Ix I/8W Carbon AA R1235 VRD-RA2BE103J R 10k I/8W Carbon AA R1620 VRD-RA2BE222J R 12.2X I/8W Carbon AA R1237 VRD-RA2BE102J R 4.7K I/8W Carbon AA R1622 VRD-RA2BE332J R 3.3X I/8W Carbon AA R1240 VRD-RA2BE102J R 1k I/8W Carbon AA R1623 VRD-RA2BE103J R 1/8W Carbon AA R1241 VRD-RA2BE101J R 100 I/8W Carbon AA R1625 VRD-RA2BE100J R 1/8W Carbon AA R1242 VRD-RA2BE101J R 100 I/8W Carbon AA R1626 VRD-RA2BE100J R 1/8 I/8W Carbon AA R1244 VRD-RA2BE101J R 1/8 V/8W Carbon AA R1626 VRD-RA2BE103J	R1234	VRD-RA	2BE562J	R	5.6k	1/8W	Carbon	AA	R1618	VRD-RA2BE103J	R	10k	1/8W	Carbon	AA
R1236 VRD-RA28E103J R 10k 1/8W Carbon AA R1620 VRD-RA28E102J R 2.2k 1/8W Carbon AA R1237 VRD-RA28E663J R 56k 1/8W Carbon AA R1621 VRD-RA28E102J R 1.k 1/8W Carbon AA R1239 VRD-RA28E102J R 1.k 1/8W Carbon AA R1623 VRD-RA28E32J R 3.3k 1/8W Carbon AA R1241 VRD-RA28E101J R 10 1/8W Carbon AA R1625 VRD-RA28E102J R 1.k 1/8W Carbon AA R1242 VRD-RA28E101J R 100 1/8W Carbon AA R1625 VRD-RA28E102J R 1.k 1/8W Carbon AA R1245 VRD-RA28E103J R 100 1/8W Carbon AA R1626 VRD-RA28E102J R 1.k	R1235	VRD-RA	2BE103J	R	10k	1/8W	Carbon	AA	R1619	VRD-RA2BE102J	R	1k	1/8W	Carbon	AA
R1237 VRD-RA2EE4/2/J H 4.7k 1/8W Carbon AA R1621 VRD-RA2EE304J R 1/8W Carbon AA R1238 VRD-RA2EE102J R 1k 1/8W Carbon AA R1622 VRD-RA2EE332J R 3.8. 1/8W Carbon AA R1240 VRD-RA2EE102J R 1k 1/8W Carbon AA R1622 VRD-RA2EE32J R 3.8. 1/8W Carbon AA R1241 VRD-RA2EE101J R 100 1/8W Carbon AA R1626 VRD-RA2EE102J R 1k 1/8W Carbon AA R1242 VRD-RA2EE101J R 100 1/8W Carbon AA R1626 VRD-RA2EE102J R 1k 1/8W Carbon AA R1245 VRD-RA2EE103J R 10k 1/8W Carbon AA R1629 VRD-RA2EE102J R 1k 1/8W Carbon AA R1245 VRD-RA2EE103J R 10k 1/8W Carbon AA R1629 VRD	R1236	VRD-RA	2BE103J	R	10k	1/8W	Carbon	AA	R1620	VRD-RA2BE222J	R	2.2k	1/8W	Carbon	AA
n1239 VID-nA2EE103J R 16 160 1/8W Carbon AA R1622 VID-nA2EE134J R 3.3k 1/8W Carbon AA R1240 VRD-RA2EE102J R 1k 1/8W Carbon AA R1623 VRD-RA2EE101J R 3.3k 1/8W Carbon AA R1241 VRD-RA2EE101J R 100 1/8W Carbon AA R1625 VRD-RA2EE102J R 1k 1/8W Carbon AA R1242 VRD-RA2EE101J R 100 1/8W Carbon AA R1625 VRD-RA2EE102J R 1k 1/8W Carbon AA R1242 VRD-RA2EE103J R 100 1/8W Carbon AA R1628 VRD-RA2EE102J R 1k 1/8W Carbon AA R1244 VRD-RA2EE103J R 10k 1/8W Carbon AA R1630 VRD-RA2EE102J R 1k 1/8W Carbon AA R1244 VRD-RA2EE103J R 10k 1/8W Carbon AA	R1237		A2BE4/2J	К	4.7k	1/8W	Carbon	AA	R1621	VRD-RA2BE102J	R	1k	1/8W	Carbon	AA
A1240 VRD-RA2BE102J R IK I/W Carbon AA R1623 VRD-RA2BE132J R IX I/W Carbon AA R1241 VRD-RA2BE101J R 100 1/W Carbon AA R1625 VRD-RA2BE102J R 1K 1/W Carbon AA R1242 VRD-RA2BE101J R 100 1/W Carbon AA R1625 VRD-RA2BE102J R 1K 1/W Carbon AA R1243 VRD-RA2BE101J R 100 1/W Carbon AA R1625 VRD-RA2BE102J R 1K 1/W Carbon AA R1244 VRD-RA2BE103J R 100 1/W Carbon AA R1629 VRD-RA2BE102J R 1K 1/W Carbon AA R1244 VRD-RA2BE103J R 10k 1/W Carbon AA R1631 VRD-RA2BE102J R 1K 1/W Carbon AA (29HX5) R 1/K 1/W Carbon AA (29HX5) R 1/K 1/W	R1230		2BE003J	R	56К 11-	1/877	Carbon		R1622	VRD-RA2BE394J	R	390	< 1/8W	Carbon	AA
R1241 VRD-RA2BE101J R 100 1/8W Carbon AA R1625 VRD-RA2BE102J R 14 1/8W Carbon AA R1242 VRD-RA2BE101J R 100 1/8W Carbon AA R1625 VRD-RA2BE102J R 1k 1/8W Carbon AA R1242 VRD-RA2BE101J R 100 1/8W Carbon AA R1625 VRD-RA2BE102J R 1k 1/8W Carbon AA R1244 VRD-RA2BE101J R 100 1/8W Carbon AA R1629 VRD-RA2BE102J R 1k 1/8W Carbon AA R1245 VRD-RA2BE103J R 10k 1/8W Carbon AA R1629 VRD-RA2BE102J R 1k 1/8W Carbon AA R1244 VRD-RA2BE103J R 10k 1/8W Carbon AA R1630 VRD-RA2BE102J R 1/k MW Carbon AA R1244 VRD-RA2BE103J R 10k 1/8W Carbon AA R1631 VRN-VV3DB5R6J R 5.6 2W Carbon AA R1244 VRD-RA2BE103J R 10k	R1240	VRD-RA	2BE1023	R	1k	1/8W	Carbon		R 1623		R	3.3k	1/8W	Carbon	AA
R1242 VRD-RA2BE101J R 100 1/8W Carbon AA R1626 VRD-RA2BE100J R 10 1/8W Carbon AA R1243 VRD-RA2BE101J R 100 1/8W Carbon AA R1627 VRD-RA2BE102J R 1k 1/8W Carbon AA R1244 VRD-RA2BE101J R 100 1/8W Carbon AA R1628 VRD-RA2BE102J R 1k 1/8W Carbon AA R1245 VRD-RA2BE103J R 10k 1/8W Carbon AA R1629 VRD-RA2BE102J R 1k 1/8W Carbon AA R1244 VRD-RA2BE103J R 10k 1/8W Carbon AA R1629 VRD-RA2BE102J R 1k 1/8W Carbon AA R1249 VRD-RA2BE103J R 10k 1/8W Carbon AA R1631 VRD-RA2BE31J R 30 1/8W Carbon AA R1252 VRD-RA2BE103J R 10k 1/8W Carbon AA R1631 VRD-RA2BE31J R 30 1/8W Carbon AA R1252 VRD-RA2BE103J R 10k	R1241	VRD-RA	2BE101J	R	100	1/8W	Carbon	AA	R1624	VRD-RA2BE4/1J	R	470 11	1/877	Carbon
R1243 VRD-RA2BE101J R 100 1/8W Carbon AA R1627 VRD-RA2BE102J R 1k 1/8W Carbon AA R1244 VRD-RA2BE101J R 100 1/8W Carbon AA R1628 VRD-RA2BE102J R 1k 1/8W Carbon AA R1245 VRD-RA2BE103J R 10k 1/8W Carbon AA R1629 VRD-RA2BE102J R 1k 1/8W Carbon AA R1247 VRD-RA2BE103J R 10k 1/8W Carbon AA R1639 VRD-RA2BE101J R 10c 1/2W Carbon AA R1248 VRD-RA2BE103J R 10k 1/8W Carbon AA R1631 VRN-VV3DB5R6J R 5.6 2W Metal Film AA R1252 VRD-RA2BE103J R 1/k 1/8W Carbon AA R1631 VRD-RA2BE31J R 300 1/8W Carbon AA R1252 VRD-RA2BE103J R 1/k 1/8W Carbon AA R1631	R1242	VRD-RA	2BE101J	R	100	1/8W	Carbon	AA	R1626	VRD-RA2BE102J	R	10	1/8W	Carbon
R1244 VRD-RA2BE101J R 100 1/8W Carbon AA R1628 VRD-RA2BE102J R 1k 1/8W Carbon AA R1245 VRD-RA2BE103J R 10k 1/8W Carbon AA R1629 VRD-RA2BE102J R 1k 1/8W Carbon AA R1246 VRD-RA2BE103J R 10k 1/8W Carbon AA R1630 VRD-RA2BE102J R 1k 1/8W Carbon AA R1247 VRD-RA2BE103J R 10k 1/8W Carbon AA R1631 VRN-VV3DB5R5J R 5.6 2W Metal Film AA R1249 VRD-RA2BE103J R 56k 1/8W Carbon AA R1632 VRD-RA2BE101J R 0.0 1/2W Carbon AA R1251 VRD-RA2BE103J R 4.7k 1/8W Carbon AA R1632 VRD-RA2BE101J R 100 1/8W Carbon AA R1252 VRD-RA2BE103J R 10k 1/8W Carbon AA R16	R1243	VRD-RA	2BE101J	R	100	1/8W	Carbon	AA	R1627	VRD-RA2BE102J	R	1k	1/8W	Carbon
R1245 VRD-RA2BE103J R 10k 1/8W Carbon AA R1629 VRD-RA2BE102J R 1k 1/8W Carbon AA R1246 VRD-RA2BE103J R 10k 1/8W Carbon AA R1630 VRD-RA2BE101J R 10k 1/8W Carbon AA R1247 VRD-RA2BE103J R 10k 1/8W Carbon AA R1631 VRN-VV3DB5R6J R 5.6 2W Metal Film AA R1249 VRD-RA2BE103J R 5.6 1/8W Carbon AA R1631 VRN-VV3DB5R6J R 5.6 2W Metal Film AA R1252 VRD-RA2BE103J R 1.6 1/8W Carbon AA R1632 VRD-RA2BE101J R 1.0 1/2W Carbon AA R1252 VRD-RA2BE103J R 1.0k 1/8W Carbon AA R1633 VRD-RA2BE101J R 1.0 1/2W Carbon AA R1255 VRD-RA2BE103J R 1.0k 1/8W Carbon AA	R1244	VRD-RA	2BE101J	R	100	1/8W	Carbon	AA	R1628	VRD-RA2BE102J	R	1k	1/8W	Carbon	AA
R1246 VRD-RA2BE103.J R 10k 1/8W Carbon AA R1630 VRD-RM2HD101.J R 100 1/2W Carbon AA R1247 VRD-RA2BE103.J R 10k 1/8W Carbon AA R1631 VRD-RA2BE10.J R 5.6 2W Metal Film AA R1249 VRD-RA2BE472.J R 5.6k 1/8W Carbon AA R1632 VRD-RA2BE33.J R 5.6 2W Metal Film AA R1251 VRD-RA2BE472.J R 4.7k 1/8W Carbon AA R1632 VRD-RA2BE31.J R 3.0 1/8W Carbon AA R1252 VRD-RA2BE103.J R 10k 1/8W Carbon AA R1633 VRD-RA2BE101.J R 100 1/2W Carbon AA R1252 VRD-RA2BE103.J R 10k 1/8W Carbon AA R1633 VRD-RA2BE101.J R 100 1/8W Carbon AA R1254 VRD-RA2BE472.J R 4.7k 1/8W Carbon AA	R1245	VRD-RA	2BE103J	R	10k	1/8W	Carbon	AA	R1629	VRD-RA2BE102J	R	1k	1/8W	Carbon	AA
H1247 VHD-HA2BE103J R 10k 1/8W Carbon AA (29HX5) R1248 VRD-RA2BE103J R 10k 1/8W Carbon AA R1631 VRN-VV3DB5R6J R 5.6 2W Metal Film AA R1249 VRD-RA2BE563J R 5.6k 1/8W Carbon AA R1631 VRN-V3DB5R6J R 5.6 2W Metal Film AA R1251 VRD-RA2BE472J R 4.7k 1/8W Carbon AA R1633 VRD-RA2BE331J R 100 1/2W Carbon AA R1252 VRD-RA2BE103J R 10k 1/8W Carbon AA R1635 VRD-RA2BE101J R 100 1/2W Carbon AA R1254 VRD-RA2BE103J R 10k 1/8W Carbon AA R1636 VRD-RA2BE102J R 8.2 1/2W Carbon AA R1255 VRD-RA2BE103J R 16 1/8W Carbon AA R1637 VRD-RA2BE102J R 1k 1/8W Carbon	R1246	VRD-RA	2BE103J	R	10k	1/8W	Carbon	AA	R1630	VRD-RM2HD101J	R	100	1/2W	Carbon	AA
N1248 VRD-RA2BE 103J R 10k 1/8W Carbon AA R1631 VRN-VV3DB5R6J R 5.6 2W Metal Film AA R1249 VRD-RA2BE 103J R 56k 1/8W Carbon AA (29HX5) R1251 VRD-RA2BE102J R 4.7k 1/8W Carbon AA R1632 VRD-RA2BE101J R 100 1/2W Carbon AA R1252 VRD-RA2BE103J R 1k 1/8W Carbon AA R1634 VRD-RA2BE101J R 100 1/2W Carbon AA R1253 VRD-RA2BE103J R 10k 1/8W Carbon AA R1634 VRD-RA2BE101J R 100 1/2W Carbon AA R1254 VRD-RA2BE103J R 10k 1/8W Carbon AA R1635 VRD-RA2BE102J R 1/8W Carbon AA R1255 VRD-RA2BE103J R 56 1/2W Carbon AA R1637 VRD-RA2BE102J R 1/8 U Carbon AA	R1247	VRD-RA	2BE103J	R	10k	1/8W	Carbon	AA				(29H	X5)
R1243 VRD-RA2BE1033 R 4.8 (29HX5) R1251 VRD-RA2BE1472J R 4.7 1/8W Carbon AA R1632 VRD-RA2BE31J R 3.00 1/8W Carbon AA R1252 VRD-RA2BE102J R 1.k 1/8W Carbon AA R1633 VRD-RA2BE101J R 100 1/2W Carbon AA R1253 VRD-RA2BE103J R 10k 1/8W Carbon AA R1635 VRD-RA2BE101J R 100 1/8W Carbon AA R1254 VRD-RA2BE103J R 10k 1/8W Carbon AA R1635 VRD-RA2BE101J R 82 1/2W Carbon AA R1255 VRD-RA2BE103J R 4.7k 1/8W Carbon AA R1636 VRD-RA2BE102J R 1k 1/8W Carbon AA R1255 VRD-RA2BE103J R 6 1/2W Carbon AA R1637 VRD-RA2BE102J R 1k 1/8W Carbon AA R1257 VRD	R1240		285562 I	R	TUK	1/877	Carbon		R1631	VRN-VV3DB5R6J	R	5.6	2W	Metal Film	AA
R1252 VRD-RA2BE102J R NR	R1240	VRD-RA	2BE472.1	R	2 7k	1/8\//	Carbon		P1c22			(29H	X5)	.
R1253 VRD-RA2BE103J R 10k 1/8W Carbon AA R1643 VRD-RA2BE101J R 100 1/8W Carbon AA R1254 VRD-RA2BE103J R 10k 1/8W Carbon AA R1634 VRD-RA2BE101J R 100 1/8W Carbon AA R1255 VRD-RA2BE472J R 4.7k 1/8W Carbon AA R1635 VRD-RA2BE101J R 82 1/2W Carbon AA R1255 VRD-RA2BE472J R 4.7k 1/8W Carbon AA R1636 VRD-RA2BE102J R 1k 1/8W Carbon AA R1256 VRD-RA2BE103J R 56 1/2W Carbon AA R1636 VRD-RA2BE102J R 1k 1/8W Carbon AA R1257 VRD-RA2BE103J R 10k 1/8W Carbon AA R1637 VRD-RA2BE102J R 1k 1/8W Carbon AA R1259 VRD-RA2BE101J R 10k 1/8W Carbon AA R1640<	R1252	VRD-RA	2BE102J	R	1k	1/8W	Carbon	ΔΔ ΔΔ	R1633	VRD-RAZBE331J	R	330	1/877	Carbon
R1254 VRD-RA2BE103J R 10k 1/8W Carbon AA R1635 VRD-RM2HD820J R 82 1/2W Carbon AA R1255 VRD-RA2BE472J R 4.7k 1/8W Carbon AA R1635 VRD-RM2HD820J R 82 1/2W Carbon AA R1256 VRD-RA2BE472J R 4.7k 1/8W Carbon AA R1636 VRD-RA2BE102J R 82 1/2W Carbon AA R1257 VRD-RA2BE103J R 10k 1/8W Carbon AA R1639 VRD-RA2BE102J R 1k 1/8W Carbon AA R1259 VRD-RA2BE101J R 1k 1/8W Carbon AA R1640 VRD-RA2BE223J R 2.k 1/8W Carbon AA R1260 VRD-RA2BE101J R 100 1/8W Carbon AA R1641 VRD-RA2BE103J R 10k 1/8W Carbon AA R1261 VRD-RA2BE101J R 100 1/8W Carbon AA R1641<	R1253	VRD-RA	2BE103J	R	10k	1/8W	Carbon	AA	R1634	VRD-RA2BE101.	R	100	1/2VV 1/8\//	Carbon	ΔΔ
R1255 VRD-RA2BE472J R 4.7k 1/8W Carbon AA R1636 VRD-RM2HD820J R 82 1/2W Carbon AA R1256 VRD-RM2HD560J R 56 1/2W Carbon AA R1637 VRD-RA2BE102J R 1k 1/8W Carbon AA R1257 VRD-RA2BE103J R 10k 1/8W Carbon AA R1637 VRD-RA2BE102J R 1k 1/8W Carbon AA R1257 VRD-RA2BE102J R 1k 1/8W Carbon AA R1638 VRD-RA2BE102J R 1k 1/8W Carbon AA R1258 VRD-RA2BE101J R 1k 1/8W Carbon AA R1639 VRD-RA2BE102J R 8.2k 1/8W Carbon AA R1260 VRD-RA2BE101J R 100 1/8W Carbon AA R1641 VRD-RA2BE103J R 10k 1/8W Carbon AA R1261 VRD-RA2BE103J R 5.6 2W Metal Film AA R1642<	R1254	VRD-RA	2BE103J	R	10k	1/8W	Carbon	AA	R1635	VRD-RM2HD820J	R	82	1/2W	Carbon
R1256VRD-RM2HD560JR561/2WCarbonAAR1637VRD-RA2BE102JR1k1/8WCarbonAAR1257VRD-RA2BE103JR101/8WCarbonAAR1638VRD-RA2BE102JR1k1/8WCarbonAAR1258VRD-RA2BE101JR1k1/8WCarbonAAR1639VRD-RA2BE822JR8.2.k1/8WCarbonAAR1259VRD-RA2BE101JR101/8WCarbonAAR1640VRD-RA2BE103JR10k1/8WCarbonAAR1260VRD-RA2BE101JR1001/8WCarbonAAR1641VRD-RA2BE103JR10k1/8WCarbonAAR1261VRN-VV3DB5R6JR5.62WMetal FilmAAR1642VRD-RA2BE103JR10k1/8WCarbonAAR1262VRD-RA2BE153JR3.91/2WCarbonAAR1643VRD-RA2BE153JR15k1/8WCarbonAAR1263VRD-RA2BE153JR15k1/8WCarbonAAR1643VRD-RA2BE153JR15k1/8WCarbonAAR1264VRD-RA2BE153JR15k1/8WCarbonAAR1643VRD-RA2BE182JR15k1/8WCarbonAAR1265VRD-RM2HD360JR561/2WCarbonAAR1644VRD-RA2BE182JR15k1/8WCarbonAA	R1255	VRD-RA	2BE472J	R	4.7k	1/8W	Carbon	AA	R1636	VRD-RM2HD820J	R	82	1/2W	Carbon	AA
R1257VRD-RA2BE103JR10k1/8WCarbonAAR1638VRD-RA2BE102JR1k1/8WCarbonAAR1258VRD-RA2BE102JR1k1/8WCarbonAAR1639VRD-RA2BE822JR88.2k1/8WCarbonAAR1259VRD-RA2BE101JR1001/8WCarbonAAR1640VRD-RA2BE23JR22k1/8WCarbonAAR1260VRD-RA2BE101JR1001/8WCarbonAAR1641VRD-RA2BE103JR10k1/8WCarbonAAR1261VRN-VV3DB5R6JR5.62WMetal FilmAAR1642VRD-RA2BE103JR10k1/8WCarbonAAR1262VRD-RA2BE153JR5.62WMetal FilmAAR1643VRD-RA2BE103JR10k1/8WCarbonAAR1263VRD-RA2BE153JR15k1/8WCarbonAAR1643VRD-RA2BE153JR15k1/8WCarbonAAR1264VRD-RA2BE153JR15k1/8WCarbonAAR1644VRD-RA2BE182JR1.8k1/8WCarbonAAR1265VRD-RM2HD330JR381/2WCarbonAAR1644VRD-RA2BE182JR1.8k1/8WCarbonAAR1266VRD-RM2HD560JR561/2WCarbonAAR1647VRD-RA2BE103JR1.8k1/8WCarbonAA	R1256	VRD-RN	12HD560J	R	56	1/2W	Carbon	AA	R1637	VRD-RA2BE102J	R	1k	1/8W	Carbon	AA
R1258 VRD-RA2BE102J R 1k 1/8W Carbon AA R1639 VRD-RA2BE822J R 8.2k 1/8W Carbon AA R1259 VRD-RA2BE101J R 100 1/8W Carbon AA R1640 VRD-RA2BE223J R 8.2k 1/8W Carbon AA R1260 VRD-RA2BE101J R 100 1/8W Carbon AA R1641 VRD-RA2BE223J R 22k 1/8W Carbon AA R1261 VRN-VV3DB5R6J R 5.6 2W Metal Film AA R1642 VRD-RA2BE103J R 10k 1/8W Carbon AA R1261 VRN-VV3DB5R6J R 5.6 2W Metal Film AA R1642 VRD-RA2BE103J R 10k 1/8W Carbon AA R1262 VRD-RA2BE153J R 3.9 1/2W Carbon AA R1643 VRD-RA2BE153J R 1/8W Carbon AA R1264 VRD-RA2BE153J R 15k 1/8W Carbon AA R1643	R1257	VRD-RA	2BE103J	R	10k	1/8W	Carbon	AA	R1638	VRD-RA2BE102J	R	1k	1/8W	Carbon	AA
R1259 VRD-RA2BE101J R 100 1/8W Carbon AA R1640 VRD-RA2BE223J R 22k 1/8W Carbon AA R1260 VRD-RA2BE101J R 100 1/8W Carbon AA R1640 VRD-RA2BE103J R 10k 1/8W Carbon AA R1261 VRN-VV3DB5R6J R 5.6 2W Metal Film AA R1642 VRD-RA2BE103J R 10k 1/8W Carbon AA R1262 VRD-RM2HD390J R 39 1/2W Carbon AA R1643 VRD-RA2BE103J R 10k 1/8W Carbon AA R1263 VRD-RA2BE153J R 15k 1/8W Carbon AA R1643 VRD-RA2BE153J R 15k 1/8W Carbon AA R1264 VRD-RA2BE153J R 15k 1/8W Carbon AA R1643 VRD-RA2BE153J R 15k 1/8W Carbon AA R1264 VRD-RA2BE153J R 15k 1/8W Carbon AA R1	R1258	VRD-RA	2BE102J	R	1k	1/8W	Carbon	AA	R1639	VRD-RA2BE822J	R	8.2k	1/8W	Carbon	AA
R1260 VRD-RA2BE101J R 100 1/8W Carbon AA R1641 VRD-RA2BE103J R 10k 1/8W Carbon AA R1261 VRN-VV3DB5R6J R 5.6 2W Metal Film AA R1642 VRD-RA2BE103J R 10k 1/8W Carbon AA R1262 VRD-RM2HD390J R 39 1/2W Carbon AA R1642 VRD-RA2BE103J R 10k 1/8W Carbon AA R1263 VRD-RA2BE153J R 15k 1/8W Carbon AA R1643 VRD-RA2BE153J R 15k 1/8W Carbon AA R1264 VRD-RA2BE153J R 15k 1/8W Carbon AA R1643 VRD-RA2BE153J R 15k 1/8W Carbon AA R1265 VRD-RA2BE153J R 15k 1/8W Carbon AA R1644 VRD-RA2BE182J R 1.8k 1/8W Carbon AA R1265 VRD-RM2HD300J R 56 1/2W Carbon AA R1	R1259	VRD-RA	2BE101J	R	100	1/8W	Carbon	AA	R1640	VRD-RA2BE223J	R	22k	1/8W	Carbon	AA
R1261 VRD-RV3DB5R60 R 5.6 2VV Metal Film AA R1642 VRD-RA2BE103J R 10k 1/8W Carbon AA R1262 VRD-RM2HD390J R 39 1/2W Carbon AA (29HX5) (29HX5) R1263 VRD-RA2BE153J R 15k 1/8W Carbon AA R1643 VRD-RA2BE153J R 15k 1/8W Carbon AA R1264 VRD-RA2BE153J R 15k 1/8W Carbon AA (29HX5) (29HX5) R1265 VRD-RA2BE153J R 15k 1/8W Carbon AA (29HX5) R1266 VRD-RM2HD330J R 33 1/2W Carbon AA R1644 VRD-RA2BE182J R 1.8k 1/8W Carbon AA R1266 VRD-RM2HD560J R 56 1/2W Carbon AA R1647 VRD-RA2BE103J R 10k 1/8W Carbon AA R1267 VRD-RA2BE333J R 33k 1/8W Carbon	R1260		2BE101J	К	100	1/8W	Carbon	AA	R1641	VRD-RA2BE103J	R	10k	1/8W	Carbon	AA
R1262 VRD-RM2H05303 R 39 1/2W Carbon AA (29HX5) R1263 VRD-RA2BE153J R 15k 1/8W Carbon AA R1643 VRD-RA2BE153J R 15k 1/8W Carbon AA R1264 VRD-RA2BE153J R 15k 1/8W Carbon AA (29HX5) (29HX5) R1265 VRD-RA2BE153J R 15k 1/8W Carbon AA (29HX5) (29HX5) R1265 VRD-RM2HD330J R 33 1/2W Carbon AA R1644 VRD-RA2BE182J R 1.8k 1/8W Carbon AA R1266 VRD-RM2HD560J R 56 1/2W Carbon AA R1647 VRD-RA2BE103J R 10k 1/8W Carbon AA R1267 VRD-RA2BE333J R 33k 1/8W Carbon AA R1648 VRD-RA2BE333J R 33k 1/8W Carbon AA R1269 VRD-RA2BE333J R 33k 1/8W Carbon AA R1649	R1201			к	5.6	270	Metal Film	AA	R1642	VRD-RA2BE103J	R	10k	1/8W	Carbon	AA
R1260 MB 10 k 10	R1262		2RE1531	R	১৬ 15৮	1/ZVV 1/8\//	Carbon	АА	D1640		-	(29H	X5)	0
R1265 VRD-RM2HD330J R 33 1/2W Carbon AA R1644 VRD-RA2BE182J R 1.8k 1/8W Carbon AA R1266 VRD-RM2HD560J R 56 1/2W Carbon AA R1644 VRD-RA2BE103J R 1.8k 1/8W Carbon AA R1266 VRD-RM2HD560J R 56 1/2W Carbon AA R1647 VRD-RA2BE103J R 10k 1/8W Carbon AA R1267 VRD-RA2BE333J R 33k 1/8W Carbon AA R1648 VRD-RA2BE333J R 33k 1/8W Carbon AA R1269 VRD-RA2BE333J R 33k 1/8W Carbon AA R1649 VRD-RA2BE102J R 1k 1/8W Carbon AA	R1264	VRD-RA	2BE153.	B	15k	1/8W/	Carbon		n 1643	VND-KAZBE153J	к	15k (2011	1/8W	Carbon	AA
R1266VRD-RM2HD560JR 561/2WCarbonAAR1647VRD-RA2BE103JR 10k1/8WCarbonAAR1267VRD-RA2BE333JR 33k1/8WCarbonAAR1648VRD-RA2BE333JR 33k1/8WCarbonAAR1269VRD-RA2BE333JR 33k1/8WCarbonAAR1649VRD-RA2BE102JR 1k1/8WCarbonAA	R1265	VRD-RM	2HD330.1	R	33	1/2W	Carbon	ΑΔ	R1644		Þ	(29H	1/0\A	Corbon	A A
R1267 VRD-RA2BE333J R 33k 1/8W Carbon AA R1648 VRD-RA2BE333J R 33k 1/8W Carbon AA R1269 VRD-RA2BE333J R 33k 1/8W Carbon AA R1649 VRD-RA2BE102J R 1k 1/8W Carbon AA	R1266	VRD-RM	2HD560J	R	56	1/2W	Carbon	AA	R1647	VRD-RA2BE102J	R	т.ок 1∩⊮	1/8\A/	Carbon
R1269 VRD-RA2BE333J R 33k 1/8W Carbon AA R1649 VRD-RA2BE102J R 1k 1/8W Carbon AA	R1267	VRD-RA	2BE333J	R	33k	1/8W	Carbon	AA	R1648	VRD-RA2BE333J	R	33k	1/8W	Carbon	AA
	R1269	VRD-RA	2BE333J	R	33k	1/8W	Carbon	AA	R1649	VRD-RA2BE102J	R	1k	1/8W	Carbon	AA

SHARP Service manual / Схема, сервісна інструкція Service manual & schematics

SERVICE MANUAL 维修手册

WARNING

告

ELECTRICAL SPECIFICATIONS

电路规格

IMPORTANT SERVICE NOTES

SERVICING OF HIGH VOLTAGE SYSTEM AND PICTURE TUBE

X-RAY

BEFORE RETURNING THE RECEIVER

保养维修重要注意事项

关于X射线

维修后归还之前

ADJUSTMENT PRECAUTIONS

1) Calling the service mode by the microprocessor

2) Factory presettings

调整时注意再加

2) 初始值 (预设值) 的设定

(6) The following key inputs call their corresponding modes.

(4)改变保养调整状态时,最后被设定的保养调整数据存储于EEPROM之中。

(5)在保养调整状态下。用户数据的预设位量如下:

(6)触按以下键钮,即可呼出与其相应的保养调整状态。

(7) The data in the adjust modes are adjustable in the following ranges.

(8) INSET PICTURE SERVICE MODE

(8)子荧屏侵养调整状态

(9) Here is a list of the initial data of inset picture (initialized in the same way as in (3)) and the adjustable ranges in the inset picture service mode.

(9)子荧屏的初始数据(按与(3)相同方法进行初始值的处理) 与子荧屏保养调整状态的调整范围如下表示。

SERVICE ADJUSTMENT

■ + B (120V) ADJUSTMENT

1. + 120V ADJUSTMENT: R733

2. SUB-POWER ADJUSTMENT: R747

PIE/AFT/AGC ADUISTMENT

1. TUNER IFT (1) ADJUSTMENT: TU5201 (preset)

保养调整

■ PIF/AFT/AGC 的 调 略

PIF/AFT/AGC ADJUSTMENT

3. VCO FREE-RUN ADJUSTMENT: T2203 (on RiFU-0040CEZZ, preset)

4. S-DET ADJUSTMENT (on RiFU-0040CEZZ, preset)

5. AFT ADJUSTMENT (1): T2204 (on RIFU-0040CF77)

6 AFT ADJUSTMENT (2) T5801

PIF/AFT/AGC ADJUSTMENT

7 REAGC CUT-IN ADJUSTMENT (1): R5214

8. RF AGC CUT-IN ADJUSTMENT (2)

(bus adjustment, inset picture service mode)

9. VIDEO DETECTION LEVEL ADJUSTMENT: 85218

■ PIF/AFT/AGC的 调整

3. CONTRAST ADJUSTMENT: IC5802 (IF, V, C, J IC) (bus adjustment, inset picture service mode)

SOUND ADJUSTMENT

SYNC DETECTION ADJUSTMENT

1. SYNC DETECTION FREQUENCY ADJUSTMENT: R5656

SIF (NICAM) ADJUSTMENT

1. CARRIER DETECTION COIL: T5303

■ 声音 制式 的 调整

SIF(NICAM制式)的调整

■ SIF (IGR) ADJUSTMENT (29HX5 ONLY)

1. S-DET: T5301 (5 5M) T5302 (5 74M)

2. AUDIO LEVEL: R5311

Under the same signal conditions as above, do the following,

3. SEPARATION: R5310

Under the same signal conditions as above, do the following. Set the signal generator to STEREO mode (Push the L or R switch). Turn off the MONO1 (L) audio signal

4. TEXT LEVEL: R1815

■中音频SIF(IGR)的调整(只限于型号29HX5)

■ INSET PICTURE OUTPUT LEVEL ADJUSTMENT

1. SUB-CONTRAST ADJUSTMENT: IC4805 (RGB output) (bus adjustment, inset picture service mode) 1. Bereive the "PAL COLOUR BAR" sincel Set the S. Main picture's 100% white

2. SUB-BRIGHTNESS ADJUSTMENT: IC805 (RGB output) (inset picture service mode)

3. WHITE BALANCE ADJUSTMENT (inset picture service mode)

PURITY ADJUSTMENT

子荧屏输出电平的调整

■ 色彩纯度的调整

CONVERGENCE ADJUSTMENT

(To be done after the purity adjustment)

STATIC CONVERGENCE

DYNAMIC CONVERGENCE

静聚焦度的调整

动聚焦度的调整

CRT Cut-Off, Background and Sub-Contrast Adjustments

3. SUB-CONTRAST ADJUSTMENTS

HORIZONTAL AND VERTICAL CIRCUIT ADJUSTMENT

1. SERVICE MODE DATA ADJUSTMENT

2. FOCUS ADJUSTMENT

■ PIF/AFT/AGC 的调略

■ PIF/AFT/AGC的调整

■ 声音制式的调整

(I²C bus adjustment, main picture)

(main picture, I²C bus adjustment, inset picture)

(I²C bus adjustment)

(I²C bus adjustment)