Thank you for purchasing this SHARP product. To obtain the best performance
from this product, please read this manual carefully. It will guide you in operating your SHARP product.
SD-AS10W 1-Bit Digital Home Theater with DVD consisting of SD-AS10W (main unit
and amplifier unit), CP-AS10WF (front speakers), CP-AS10WC (centre speaker), CPAS10WR (surround speakers) and CP-AS10WSW (subwoofer).
Special notes
Icons used in this operation manual
Some functions may not be available depending on discs. The following icons
indicate the discs that can be used in the section.
... DVD-Video discs and DVD-R/DVD-RW.
... Super video CDs.
... Video CDs.
... Audio CDs.
... CD-R/CD-RW with MP3 recording.
... CD-R/CD-RW with WMA recording.
... CD-R/CD-RW with JPEG recording.
WARNING
! When the ON/STAND-BY button is set at STAND-BY position, mains voltage is still
present inside the unit. When the ON/STAND-BY button is set at STAND-BY position, the unit may be brought into operation by the timer mode or remote control.
! This unit contains no user serviceable parts. Never remove covers unless qualified
to do so. This unit contains dangerous voltages, always remove mains plug from
the socket before any service operation and when not in use for a long period.
! To prevent fire or shock hazard, do not e xpose this appliance to dripping or splash-
ing. No objects filled with liquids, such as vases, should be placed on the apparatus.
"DTS" and "DTS Digital Surround" are regist ered tra dema rks of Digit al The ate r Syste ms,
Inc.
- Introduction / Special notes -
Important Instruction
Manufactured under li cense fro m Dolby Laborat ories. "Dolby ", "Pro Lo gic" and the doubleD symbol are trademarks of Dolby Laboratories.
This product is classified as a CLASS 1 LASER product.
The letters in brackets contai ned in the model number indicate the colour of the product
only. Operation and spec ifications are unaffected.
E-1
Types of playable DVD discs vary depending on the region. This unit can play back
only DVDs with the region number shown on the bottom of the unit or with "ALL".
ALL
324
and
05/3/18SD-AS10W_EX_E.fm
TINSZA124AWZZ
1
Accessories
Please confirm that the following accessories are included.
SD-AS10W
ENGLISH
E
Remote control 1"AA" size battery (UM/SUM-3,
R6, HP-7 or similar) 2
FM aerial 1AM loop aerial 1Button name label 1
Main unit leg cushion 4Non-slip sheet for speakers 20Speaker wire 6
Note:
Only the above accessories are included.
System connection cable 1Video cable 1Main unit stand 1
White
(for left front
speaker)
approx. 5 m (16 feet)
Purple
(for subwoofer)
approx. 5 m (16 feet)
Green
(for centre
speaker)
approx. 5 m (16 feet)
Blue
(for left surround
speaker)
approx. 15 m (49 feet)
Red
(for right front
speaker)
approx. 5 m (16 feet)
Grey
(for right surround
speaker)
approx. 15 m (49 feet)
! Please ensure that the equipment is positioned in a well ventilated area and that
there is at least 10 cm (4") of free space along the sides and back. There must also
be a minimum of 15 cm (6") of free space on the top of the unit.
Main unit
10 cm (4")10 cm (4")
Position A
15 cm (6")
! Do not place anything on top of the unit.
! Do not expose the unit to moisture, to temperatures higher than 60°C (140°F) or to
extremely low temperatures.
! If the unit does not work properly, unplug and plug it in again. Then turn on the unit.
! In case of an electrical storm, unplug the unit for safety.
! Hold the AC power plug by the head when removing it from the wall socket, as pull-
ing the lead can damage internal wires.
! Do not remove the outer cover, as this may result
in electric shock. Refer internal service to your local SHARP service facility.
SD-AS10W
ENGLISH
E
F
Position B
10 cm (4")10 cm (4")
Position C
Amplifier unit
! Use the unit on a firm, level surface free from vibra-
tion.
! Keep the unit away from direct sunlight, strong mag-
netic fields, excessive dust, humidity and electronic/
electrical equipment (home computers, facsimiles,
etc.) which generate electrical noise.
10 cm (4")10 cm (4")
10 cm (4")10 cm (4")
15 cm (6")
15 cm (6")
15 cm (6")
10 cm (4")
10 cm (4")
10 cm (4")
10 cm (4")
! The ventilation should not be impeded by covering
the ventilation openings with items, such as newspapers, tablecloths, curtains, etc.
! No naked flame sources, such as lighted candles,
should be placed on the apparatus.
! Attention should be drawn to the environmental aspects of battery disposal.
! This unit should only be used within the range of 5°C - 35°C (41°F - 95°F).
Warning:
The voltage used must be the same as that specified by this unit. Using this product
with a higher voltage other than that specified is dangerous and may result in a fire or
other types of accident, causing damage. SHARP will not be held responsible for any
damage resulting from the use of this unit with a voltage other than that specified.
" Volume control
The sound level at a given volume setting depends on speaker efficiency, location,
and various other factors. It is advisable to avoid exposure to high volume levels. Do
not turn the volume on to full at switch on and listen to music at moderate levels.
S
V
I
- Precautions -
N
General Information
P
E
E-4
SD-AS10W_EX_E.fm05/3/18
TINSZA124AWZZ
SD-AS10W
ENGLISH
General Information
E-5
Description of discs
" Types of playab le discs
The unit can play back discs bearing any of the following marks:
DVD
DVD-Video DiscDVD-RDVD-RW
4.7
Recorded in the video
mode (*)
Some DVD discs may not function as described in the manual. See the disc
jacket for restrictions.
Video CD
Super Video CDVideo CD
- Description of discs -
CD
Audio CDAudio CD-RAudio CD-RW
Or CD-R recorded in MP3/
WMA/JPEG format (*)
(*) Some discs may not play properly due to the status of the equipment used for re-
cording, characteristics of the discs, scratches, dirt, or dirty optical pickup lens.
! 8 cm (3") discs are not supported (disc adaptor cannot be used).
Recorded in the video
mode (*)
Discs recorded in VR
mode (Video Recording
format) cannot be played
back.
Or CD-RW recorded in
MP3/WMA/JPEG format
(*)
" Discs that cannot be played
! DVDs without the region number "2",
"3", "4" or "ALL".
! DVDs with SECAM system! CDG
! DVDs with MPEG sound! Photo CD
! DVD-ROM! CD-R OM
! DVD-RAM! Discs recorded in special formats, etc.
Notes:
! The discs above cannot be played at all, or no sound is heard although images
appear on the screen or vice versa.
! Faulty playback may damage the speakers and can have an adverse effect on
your hearing when played at high volume settings.
! You cannot play illegally produced discs.
! DVD-Audio
! SACD
" DVD-Video
A popular type of DVD disc of the same size as a CD, mainly containing video
images.
Region number
DVD discs are programmed with region numbers indicating countries in which they can be
played. This unit can play discs with region
number "2", "3", "4" or "ALL".
Region number
(playable area number)
2
34
ALL
Title and chapter
DVD-Video discs are divided into "titles" and
"chapters". If the disc has more than one movie
on it, each movie is a separate "title". "Chapters" are subdivisions of titles.
Title 1Title 2
Chapter 1
Chapter 2 Chapter 1 Chapter 2
" DVD-R/DVD-RW playback
! You can play DVD-R and DVD-RW discs recorded in the video mode.
! Before playing DVD-R/DVD-RW discs with this unit, finalize them with the
equipment used for recording.
" Super video CD/video CD/CD
Track
Super video CD/video CD and audio CD are
composed of "tracks". Tracks are equivalent to
songs on a CD.
Track 1 Track 2 Track 3
SD-AS10W_EX_E.fm05/3/18
TINSZA124AWZZ
" MP3/WMA/JPEG format on CD-R/CD-RW
An MP3 file is an audio data compressed in the MPEG 1 audio layer 3 format. MP3
files have the extension ".mp3". (Files with the extension ".mp3" may not play, or
noise may occur during playback if not recorded in the MP3 format.)
WMA is an audio file format developed by Microsoft with the ".wma" extension. This
type of audio file is recorded through Microsoft Windows operating system.
A JPEG file is still image data compressed in the JPEG (Joint Photographic Experts
Group) format. JPEG files have the extension ".jpg".
Folder and file
MP3/WMA/JPEG discs consist of "folders" and "files".
MP3
WMA
disc
" Icons used on DVD discs
Check the icons of the DVD jacket before playing your discs.
Format recorded on the DVD
JPEG
disc
disc
Folder
1
File 1File
2
File
Folder
File 1File
3
DisplayDescription
Select a type according to the connected
TV type.
2
2
Copyright Information:
! Unauthorised copying, broadcast, public display, transmission, public perfor-
mance and rental (regardless of whether or not such activities are for profit) of
disc contents are prohibited by law.
! This system is equipped with copy protection technology that causes substantial
degradation of images when the contents of a disc are copied to a videotape.
Copy Protection:
This unit supports Macrovision copy protection.
On DVD discs that include a cop y protection code, if the contents of the DVD disc are
copied using a VCR, the copy protection code prevents the videotape copy from playing normally.
Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, 4,819,098 and
4,907,093 licensed for limited viewing uses only.
This product incorporates copyright protection technology that is protected by
method claims of certain U.S. patents and other intellectual property rights owned
by Macrovision Corporation and other rights owners.
Use of this copyright protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
0407
SD-AS10W
ENGLISH
E
F
S
V
I
Type of subtitles recorded
Example:You can select a subtitle language.
2
1: English
2: German
Number of camera angles
2
Number of audio tracks and audio
recording systems
Example:! You can change the audio language.
1: Original <English> (Dolby Dig-
ital 5.1 Surround)
2: German (Dolby Digital 2 ch)
Recorded subtitle languages.
Number of angles recorded on the DVD.
You can view scenes from different an-
gles.
The number of audio tracks and audio recording systems are indicated.
! Audio and recording system vary de-
pending on the DVD. Check them in
the DVD's manual.
Note:
Supply of this product does not convey a license nor imply any right to distribute
content created with this product in revenue-generating broadcast systems
(terrestrial, satellite, cable and/or other distribution channels), revenue-generating
streaming applications (via Internet, intranets and/or other networks), other revenuegenerating content distribution systems (pay-audio or audio-on-demand applications
and the like) or on revenue-generating physical media (compact discs, digital versatile
discs, semiconductor chips, hard drives, memory cards and the like). An independent
license for such use is required. For details, please visit http://mp3licensing.com.
MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson.
In "MODE 2", you can use buttons other than t he above for the same operations as in
"MODE 1".
Reference page
F
S
V
I
4
11
5
12
- Controls and indicators -
N
General Information
6
13
P
E
E-10
SD-AS10W_EX_E.fm05/3/18
TINSZA124AWZZ
SD-AS10W
ENGLISH
System installation
Installation image (with optional accessories):
Front
speaker
(left)
Subwoofer
Centre speaker
Front
speaker
(right)
" Placing the speaker system
The best surround effect will be achieved by placing each speaker at the same
distance from the listening position.
It is recommended to arrange the speakers as shown below.
Front
speaker (left)
Subwoofer
Centre
speaker
Front
speaker (right)
Default setting:
2 m (6 feet)
Preparation for Use
E-11
Surround
speaker
(left)
You can attach the floor speaker stand (optional accessory) to the front and surround
speakers.
(For details on the optional accessory, refer to page 61.)
Surround
speaker
(right)
- System installation -
" Magnetically shielded speakers
The front, surround and centre speakers may be placed beside or near the TV as
they are magnetically shielded. However, discolouration may occur depending on the
TV type.
If colour variation occurs...
Turn off the TV (with the power switch).
After 15 - 30 minutes, turn the TV on again.
If the colour variation is still present...
Move the speakers further away from the TV.
Refer to the manual of the TV for details.
Note:
The subwoofer is not magnetically shielded.
Surround
speaker (left)
Surround
speaker (right)
Notes:
! The default distance is set to 2 m (6 feet). If speakers cannot be placed at equal
distances, refer to "Speaker delay setting" (see page 43).
! Place the TV halfway between the front speakers.
! It is recommended that the centre speaker be placed near the television.
! Place the surround speakers at a position just above the height of your ears.
! You can place the subwoofer anywhere you like. As it vibrates whilst reproducing
bass, place it on a stable, sturdy surface.
Same distance
Front speaker
(left)
Centre speaker
Front speaker
(right)
SD-AS10W_EX_E.fm05/3/18
TINSZA124AWZZ
Main unit preparation
Make sure to unplug the AC power lead before installing the main unit or change the position.
Select from three installation methods according to the location.
For position A or B, make sure to use the included main unit stand. Otherwise the unit may fall.
The display direction changes according to the installation direction.
SD-AS10W
ENGLISH
E
F
Position A
1
Remove the 2 screws.
2
Secure the stand with the removed screws.2
Main unit
stand
YES
Correct
Position BPosition C
1
1
Remove the 2 screws.
Make all connections
before attaching the
stand (see pages
14, 16).
Secure the stand with the removed screws.
Main unit
stand
NO
Align the position with the remote sensor
and attach the included button name label.
Remote
sensor
2
Fit the non-slip sheets into the groove.
YES
Correct
NO
S
V
Button name label
I
- Main unit preparation -
N
Preparation for Use
P
Non-slip sheet for main unit
Notes:
! When attaching the stand, place the main unit on a cushion or soft cloth to avoid
damage.
! Use the remove d screws to secure the stand. Otherwise, the unit may break.
! Remove the only specified screws. Otherwise malfunct ion may occur. Be careful
not to lose the removed screws.
! Attach the button name label carefully. It is difficult to peel off.
Caution:
! Do not change the installation direction when the main unit is turned on. Discs may
not be read or may be damaged.
! To turn on the power after the first installation or after changing the installation
method, use the ON/STAND-BY button on the main unit. From the next time, you
can also use the remote control.
SD-AS10W_EX_E.fm05/3/18
TINSZA124AWZZ
E
E-12
SD-AS10W
ENGLISH
Preparation for Use
System connections
Make sure to unplug the AC power lead before making any connections.
TV connection (see page 16)
Connect a TV and main unit with the included video cable.
If your TV is equipped with an S-video input socket or
component video input sockets, purchase an appropriate
cable to enjoy higher quality images.
TV
Aerial connection(see page 14)
FM aerial
AM loop aerial
- System connections -
Attaching the side cover(see page 16)
You can position cables differently by changing installation.
Main unit
Connecting the system
connection cable
Amplifier unit
(see page 14)
AC power
connection
(see page 17)
E-13
Front speaker
(left)
Surround speaker
(left)
Speaker connection(see page 15)
Centre speaker
SD-AS10W_EX_E.fm05/3/18
Subwoofer
Front speaker
(right)
Surround speaker
(right)
TINSZA124AWZZ
" Connecting the system connection cable
Connect the main unit and amplifier unit as follows.
Amplifier unit
To connect:
The plug is directional.
Connect it with the arrow
pointing at the screw.
To disconnect:
Pull the plug straight out
pressing the plug.
System
connection cable
Screw
1
Push
Main unit
Arrow
2
Unplug
Aerial connection
Supplied FM aerial:
Connect the FM aerial wire to the FM 75 OHMS
socket and position the FM aerial wire in the direction where the strongest signal can be received.
Supplied AM loop aerial:
Connect the AM loop aerial wire to the AM and
GND terminals. Position the AM loop aerial for
optimum reception. Place the AM loop aerial on
a shelf, etc., or attach it to a stand or a wall with
screws (not supplied).
Note:
Placing the aerial on the unit or near the AC
power lead may cause noise pickup. Place the
aerial away from the unit for better reception.
Installing the AM loop aerial:
< Assembling >< Attaching to the wall >
FM aerialAM loop aerial
Black
White
Amplifier unit
SD-AS10W
ENGLISH
E
F
S
V
I
How to remove side cover
Remove the side cover to connect the system.
2
1
Wall Screws (not supplied)
External FM or AM aerial:
Use an external FM or AM aerial if you require better reception. Consult your dealer.
When using an external AM aerial, be sure to keep the wire of the AM loop aerial
connected.
External FM aerial
Earth rod
External AM aerial
15 m (49 feet)
7.5 m (25 feet)
Earth wire
SD-AS10W_EX_E.fm05/3/18
AM loop
aerial
TINSZA124AWZZ
N
Preparation for Use
- System connections / Aerial connection -
P
E
E-14
SD-AS10W
ENGLISH
Speaker connection
Make sure to leave the AC power lead disconnected when connecting the
speakers.
To prevent accidental short circuits between and t erminals, connect the
speaker wires to the speakers first and then to the unit.
Connect the speaker and the unit by matching the colours.
1
Connect the wires to the speakers.
Example: To connect the right surround speaker.
Caution:
! The supplied speakers are designed exclusively for the SD-AS10W. Do not
connect these speakers to other equipment. Also, do not connect other
speakers to the SD-AS10W. It may cause malfunction.
! Do not mistake the and , and right and left terminals of the speaker wires. (The
right speaker is placed on the right when you face the unit.)
! Do not let the bare speaker wires touch each other.
! Do not stand or sit on the speakers. You may be injured.
! Do not short-circuit the speaker wire. If it happens with the
power on, the protection circuit is activated and the unit is
set to the power stand-by mode. In this case, check that the
speaker wire is connected correctly before turning on the
power again.
! The speakers grilles are not removable.
! Do not allow any objects to fall into or to be placed in the bass
reflex ducts.
Incorrect
Non-slip sheet for speakers:
Attach the sheets to the bottom of the speaker to prevent it from sliding.
Preparation for Use
E-15
2
Connect the other end to the amplifier unit.
- Speaker connection -
Tube (grey)
Red
Black
Amplifier unit
RedBlack
Tube (grey)
Speaker terminal (grey)
Label
(grey)
Front/surround speakersCentre speaker
Non-slip sheet
for speakers
Non-slip sheet for speakers
SD-AS10W_EX_E.fm05/3/18
TINSZA124AWZZ
TV connection
Three types of sockets (VIDEO OUT, S-VIDEO OUT and COMPONENT VIDEO
OUT) are available for connection of a TV and this unit. Connect according to your
TV.
Connect the optional S-video cable or component video cable for higher quality DVD
images. For the component video cable, the progressive video mode is available
and you can enjoy images with less flicker (default setting: PROGRESSIVE OFF).
See page 24 for details.
Connecting to a TV with a video input socket
Main unit
To video
output socket
Connecting to a TV with an S-video input socket
Main unit
Video cable (supplied)
TV
To video
input socket
TV
Connecting to a TV with component video input sockets
Main unit
To component
video output sockets
Green
Red
Blue
Notes:
! Change the TV input in accordance with the connected socket.
! Do not conn ect other equipment between the TV and this unit. If they are con-
nected via a VCR, pictures may be distorted.
! If your TV has different indications for the component video inputs (Y, CB and CR
or Y, B-Y and P-Y), connect sockets with its matching colour.
! Do not connect to a component video input socket designed for the high-vision
system, which is not DVD-compatible (the images may be distorted or not appear).
! Using the audio cable, you can listen to the TV sound with this unit (see page 55).
Component video cable
(commercially available)
To component
video input sockets
TV
Green
Blue
Red
" Attaching the side cover
SD-AS10W
ENGLISH
Preparation for Use
E
F
S
V
I
- TV connection -
N
To S-video
output socket
S-video cable
(commercially available)
To S-video
input socket
1 After making all the connections, attach the side cover to the main unit. Fit the
claws into the holes.
2 Route all the cables through the hole of the cover.
SD-AS10W_EX_E.fm05/3/18
TINSZA124AWZZ
P
E
E-16
SD-AS10W
ENGLISH
AC power conn ection
" Connecting the AC power lead
After checking all the connections have been made correctly, plug in the amplifier
unit.
Wall socket
(AC 220 V - 240 V, 50/60 Hz)
1
2
Setting the AM/FM interval
The International Telecommunication Union (ITU) has established that member countries should maintain either a 10 kHz or 9 kHz interval between broadcasting frequencies of AM stations and 100 kHz or 50 kHz for FM stations. The illustration shows the
50/9 kHz zones (regions 1 and 3), and the 100/10 kHz zone (region 2).
Before using the unit, be sure to set it to the AM/FM tuning interval (span) used in
your area.
To change the AM/FM tuning interval:
1 Press the ON/STAND-BY button to enter the power stand-by mode.
2 Whilst holding down the TUNER (BAND) button, press the ON/STAND-BY button.
3 Within 6 seconds, press the , , or button to select the interval (span) in your
area.
The display switches each time you press the button.
1
Preparation for Use
E-17
Note:
! Unplug the AC power lead from the wall socket if the unit will not be in use for a
prolonged period of time.
! Before unplugging the AC power lead, remove all the discs.
AC Plug Adaptor
- AC power connection / Setting the AM/FM interval -
In areas (or countries) where a wall socket shown in illustration is used, connect
the unit using the AC plug adaptor supplied with the unit, as illustrated. The AC plug
adaptor is not included in areas where the wall socket and AC power plug can be
directly connected (see illustration ).
Note for users in Australia and New Zealand:
An AC plug adaptor is not supplied if the lead has an Australian Standard plug.
4 Within 6 seconds, press the ENTER button on the remote control.
The unit will enter the power stand-by mode automatically.
Note:
The AM/FM tuning interval will not change unless you press the ENTER button within
6 seconds.
Caution:
! When the unit is left for a few hours after the span is switched and the AC power
lead is disconnected, the AM span automatically returns to 9 kHz (FM span to 50
kHz). If this happens, set the span again.
! When the span is switched, all the memorised stations will be cancelled.
SD-AS10W_EX_E.fm05/3/18
TINSZA124AWZZ
SHARP TINSZA124AWZZ (W)
To turn the po wer on
2
Press the ON/STAND-BY button.
The power indicator on the amplifier unit lights up.
If the power does not turn on, check whether the power lead and system connection
cable are plugged in properly.
To set the unit to stand-by mode:
Press the ON/STAND-BY button again.
Note:
After the unit enters the power stand-by mode, wait a few seconds to turn on again.
Power indicator
Amplifier unit
Main unit
" Auto power off function
The unit enters the stand-by mode after 20 minutes of inactivity in DVD operation.
Remote control
" Battery installation
1 Open the battery cover.
2 Insert the supplied batteries ac-
cording to the direction indicate d in
the battery compartment.
When inserting or removing the batteries,
push them toward the battery terminals.
3 Close the cover .
Precautions for battery use:
! Replace all old batteries with new ones at the same time.
! Do not mix old and new batteries.
! Remove the batteries if the unit is not to be used for long periods of time. This will
prevent potential damage due to battery leakage.
Caution:
! Do not use rechargeable batteries (nickel-cadmium battery, etc.).
! Installing the batteries incorr ectly may cause the unit to malfunction.
Battery removal:
Remove the battery cover. Push each battery toward the battery terminal and take
them out.
Notes concerning use:
! Replace the batteries if the operating distance is reduced or if the operation