Sharp SB-29S, SB-29 Service Manual

Download

Page 1

SHARP SERVICE MANUAL

HOT & COLD WATER DISPENSER

MODEL SB-29 SB-29S

In the interests of user-safety (Required by safety

regulations in some countries) the set should be restore

to its original condition and only parts identical to those

specied should be used.

SHARP CORPORATION

TABLE OF CONTENTS

PARTS IDENTIFICATION AND SPECIFIC INFORMATION ...................................................

CAUTIONS FOR USE .............................................................................................................

IMPORTANT SAFETY INSTRUCTIONS ................................................................................

WIRING DIAGRAM AND CIRCUIT DIAGRAM .......................................................................

COOLING SYSTEM DIAGRAM AND HOT SYSTEM DIAGRAM ...........................................

COMPONENT REPLACEMENT PROCEDURE .....................................................................

TROUBLESHOOTING ............................................................................................................

SERVICE PARTS LIST ...........................................................................................................

Page

6 - 13

15 - 19

Page 2

PARTS IDENTIFICATION

SPECIFIC INFORMATION

Model

Rated voltage (V)

Rated frequency (Hz)

Power consumption

Hot water capacity (Litre/Hr)

Cold water capacity (Litre/Hr)

Refrigerant HFCR-134a (g)

Rated current (A)

Compressor rated input (W)

Temperature control

Dimensions (W x D x H) (mm)

Weight (kg)

SB-29 SB-29S

220

610

0.70

Thermostat

305 x 380 x 997

305 x 380 x 1,080

16.4 17.4

Model : SB-29

Model : SB-29S

Panel-B

Drain tray support

Panel-B

Faucet ass’y

(Hot water)

(Cold water)

Faucet ass’y

Push button

Lamp indicator (Hot)

Top plate

Bottle connector

Stand

Lamp indicator (Cool)

(Cool water)

(Hot water)

Drain tray

Panel-A

Push button

Page 3

CAUTIONS FOR USE

1. Do not locate your Hot & Cold water dispenser where the environment would offer any risk of water

contamination.

2. The Hot & Cold water dispenser must be located on a oor which is smooth, level and easily cleaned.

3. Do not locate the Hot & Cold water dispenser in direct sunlight.

4. Do not locate the Hot & Cold water dispenser next to a radiator.

5. Do not locate the Hot & Cold water dispenser within or directly adjacent to toilet facilities.

6. Do not use the Hot & Cold water dispenser or water bottle as a shelf for plants or objects.

7. Do not use sprays, mists or vapors around the Hot & Cold water dispenser.

8. Do not put any other liquid other than water into the Hot & Cold water dispenser.

9. Do not lay the Hot & Cold water dispenser on its side.

10. Do not leave the Hot & Cold water dispenser without a bottle tted.

11. Do not attempt to move the Hot & Cold water dispenser if there is a bottle in place.

12. The plastic part should be cleaned using mild soap and water. Do NOT use bleach or any cleaning agents

containing bleach or chlorine.

13. If the wire condenser is dusty or dirty. Wipe or blow it out cleaning so that unit can run in full efciency.

IMPORTANT SAFETY INSTRUCTIONS

1. Read all instructions before using the Hot & Cold water dispenser.

2. Keep the unit be checked by the authorized service center every 6 months is recommended.

3. Before operating this appliance, this unit must be grounded properly in order to prevent risk of current leakage.

Installation must be done together with electricity leakage protector unit.

4. Do not plug other electronic equipment in the same socket because the socket will overheat and may

result in re.

5. If the appliance is malfunction. Do not try to repair this appliance. For your own safety and using this

appliance with high efciency, contact the nearest SHARP service facility for repair.

In case of indoor installation.

Connect the grounded wire to the three-prong outlet at

grounded wire position.

Copper rod 1.5 cm. and 240 cm. in length.

(Embed into the ground)

About 30 cm.

Page 4

WIRING DIAGRAM

CIRCUIT DIAGRAM

Page 5

COOLING SYSTEM DIAGRAM

HOT WATER SYSTEM DIAGRAM

Compressor

Tank cooler

Hot water inlet tube

Silicone tube

Hot water outlet tube

Connector pipe

Silicone tube

Space tank

Heater tank ass’y

Heater set ass’y

Drain tube

Filter driers

Condenser ass’y

Capillary tube

Cooling coil

Tank cooler

Page 6

COMPONENT REPLACEMENT PROCEDURE

Before beginning the service inspection and/or repair you will need to disconnect the power cord

from the Hot & Cold water dispenser and remove the bottle from the reservoir.

1. Remove the insulating seal cork tape from terminal cover.

2. Remove the cover strap xing the terminal cover.

3. Disconnect the lead wire blue and remove the PTC relay from compressor.

4. Now the PTC relay is free.

REMOVE OF PTC RELAY

REMOVE OF THERMO MOTOR

Fig. 2

Compressor

Lead wire yellow

Terminal cover

Cover strap

Thermo motor

PTC relay

1. Remove the PTC relay in accordance with “REMOVE OF PTC RELAY”.

2. Disconnect the lead wire yellow and remove the thermo motor from compressor.

3. Now the thermo motor is free.

Fig. 1

Compressor

Cover strap

Terminal cover

Lead wire blue

PTC relay

Page 7

1. Remove 5 screws holding the condenser ass’y.

2. Disconnect 2 terminals lead wire from thermostat.

3. Remove 2 screws holding the thermostat to the thermo xing plate.

4. Now the thermostat is free.

REMOVE OF THERMOSTAT

1. Remove the terminal cover.

2. Remove the screw holding the power cord ass’y

3. Remove 2 closed terminal to power cord ass’y.

4. Now the power cord ass’y is free.

REMOVE OF POWER CORD ASS’Y

REMOVE OF FUSE ASS’Y

1. Remove the thermostat in accordance with “REMOVE OF THERMOSTAT”.

2. Disconnect the lead wire fuse.

3. Now the fuse is free.

Thermostat

Terminal

Condenser ass’y

Screw

Thermo xing plate

Fig. 4

Cover strap

Terminal cover

Thermo motor

Closed terminal

Power cord ass’y

Screw

Compressor

Stand

Fig. 3

PTC relay

Page 8

REMOVE OF PANEL B-A AND FAUCET ASS’Y

1. Remove the drain tray ass’y from the panel-B.

2. Remove 2 screws holding the top plate.

3. Separate out the top plate from the unit.

4. Remove 4 screws holding the faucet cover and detach the faucet cover.

5. Remove 2 screws holding the faucet ass’y.

6. Push the push button and insert the jig into the faucet ass’y (Hot water), push up the jig and remove the

lever faucet from the faucet body. Lift up the lever faucet of faucet ass’y (Cool water) to front.

7. Remove 4 screws holding the panel B-A and separate from the unit.

8. Release 2 faucet from the panel-B and remove the panel-A and panel-B from the stand.

9. Remove 2 screws holding the PCB Hot display and PCB Cool display from the panel-B.

10. Remove 2 screws holding the panel-A and panel-B.

11. Now the panel B-A and faucet ass’y are free.

Fig. 5

Fig. 6

Screw

Top plate

Hot water outlet tube

Cool water outlet tube

Cord band

Connector pipe

PCB Cool display

PCB Hot display

Screw

Faucet ass’y (Hot water)

Faucet ass’y (Cool water)

Faucet cover

Faucet mounting plate

Screw

Drain tray ass’y

Panel-A

Lift up

Lever faucet

Panel-B Faucet body

Faucet ass’y (Hot water)

Faucet ass’y (Cool water)

Panel-B

Screw

Push

Push up

Jig

Lever faucet

Push button

Faucet body

Page 9

REMOVE OF TEMP. FUSE ASS’Y

1. Disconnect 2 lead wires Temp. fuse ass’y and cut lead wire from the PCB Hot display.

2. Disconnect 2 terminals from thermostat and switch ON/OFF.

2. Remove the screw holding the temp. fuse ass’y to the temp. fuse angle.

3. Remove the temp. fuse ass’y from the temp. fuse angle.

4. Now the temp. fuse ass’y is free.

REMOVE OF THERMOSTAT (42oC, 93oC)

1. Disconnect 4 terminals from the thermostat.

2. Remove 4 screws holding thermostat to heater tank ass’y.

3. Now the thermostat are free.

Heater tank ass’y

Screw

Thermostat 42oC

Thermostat 93oC

Terminal

Fig. 8

Fig. 7

REMOVE OF PCB HOT DISPLAY AND PCB COOL DISPLAY

1. Remove the panel B-A in accordance with “REMOVE OF PANEL B-A”.

2. Remove 2 screws holding PCB Hot display and PCB Cool display.

3. Cut lead wires from the PCB Hot display and PCB Cool display.

4. Now the PCB Hot display and PCB Cool display are free.

PCB Hot display

PCB Cool display

Panel-B

Panel-A

Screw

Fig. 9

Thermostat

Temp. fuse angle

Temp. fuse

Screw

Lead wire for

temp. fuse white

Lead wire for temp. fuse white

Lead wire for

temp. fuse white

Terminal

PCB Hot display

Switch ON/OFF

Page 10

Note : Recheck the Hot & Cold water dispenser for water leaks, after replace or repair the faucet connector

parts and tank connector.

REMOVE OF FAUCET CONNECTOR AND TANK CONNECTOR

1. Remove the water partition from the tank cooler ass’y.

2. Remove the panel B-A and faucet ass’y in accordance with “REMOVE OF PANEL B-A AND FAUCET ASS’Y”.

3. Remove the side plate L-R in accordance with “REMOVE OF SIDE PLATE L-R”.

4. Cut the charge tube and let compressor’s coolant out off the compressor about 1 minute.

5. Blow gas 2 joints, and remove the cooling coil from the compressor, the capillary tube from the lter driers.

6. Remove the adhesive foam tape from the faucet connector and the tank connector.

7. Cut 2 cord bands holding the hot water inlet tube and cool water outlet tube.

8. Remove the faucet ass’y (Cool water) and remove 3 screws holding the heater tank ass’y.

9. Remove the thermostat ass’y from tank cooler ass’y.

10. Remove the insulation foam from the tank cooler ass’y.

11. Remove 2 mounting nuts by toolbox and detach the faucet connector and tank connector from tank cooler ass’y.

12. Now the faucet connector and tank connector are free.

Fig. 10

Toolbox

Compressor

Heater tank ass’y

Hot water inlet tube

Screw

Cord band

Tank support

Insulation foam

Mounting nut

Cooling coil

Tank cooler ass’y

Bellow cap packing

Faucet connector

Water partition

Tank connector

Cool water outlet tube

Cord band

Joint

Cooling coil

Capillary tube

Filter driers

Page 11

REMOVE OF SIDE PLATE L-R

1. Remove the panel B-A and faucet ass’y in accordance with “REMOVE OF PANEL B-A”.

2. Put the jig into rear of the unit.

3. Remove 2 screws holding the switch ON/OFF ass’y.

4. Remove 4 screws holding the condenser ass’y and remove 6 screws from the side plate L-R to the tank support.

5. Remove 4 screws holding the back plate and remove lead wire earth from side plate-L.

6. Turn front unit and remove 4 screws holding the side plate reinforce to the stand.

7. Now the side plate L-R are free.

Fig. 11

Stand

Side plate-L

Lead wire earth

Screw

Side plate reinforce

Side plate-R

Screw

Condenser ass’y

Jig

Tank support

Switch ON/OFF

SW. xing plate

Screw

Back plate

REMOVE OF SPACE TANK

1. Remove 2 screws holding the top plate and detach out the top plate from the unit.

2. Remove 4 screws holding the space tank.

3. Remove 2 clamp for silicone tube from space tank.

4. Now the space tank is free.

Fig. 12

Top plate

Tank cooler ass’y

Silicone tube

Clamp for silicone tube

Screw

Space tank

Page 12

REMOVE OF HEATER TANK ASS’Y

1. Remove the panel B-A and faucet ass’y in accordance with “REMOVE OF PANEL B-A AND FAUCET ASS’Y”.

2. Remove the thermostat in accordance with “REMOVE OF THERMOSTAT”.

3. Remove the heater set ass’y.

4. Cut 3 cord bands and remove the clamp for silicone tube.

5. Detach all tube from heater tank ass’y.

6. Remove 3 screws holding the heater tank ass’y.

7. Now the heater tank ass’y is free.

REMOVE OF HEATER SET ASS’Y

1. Remove the panel B-A and faucet ass’y in accordance with “REMOVE OF PANEL B-A AND FAUCET ASS’Y”. 2 Remove 2 screws holding the heater set support.

3. Unfasten 2 screws at the heater ass’y and then pull the heater set ass’y out of the heater tank ass’y. Fig. 13

4. Now the heater set ass’y is free.

Tank support

Cord band

Clamp for silicone tube

Heater tank

Heater tank support

Heater set

Heater holder-B

Heater holder-A

Screw

Cord band

Drain tube

Screw

Hot water inlet tube

Fig. 13

Page 13

1. Remove the side plate L-R in accordance with “REMOVE OF SIDE PLATE L-R”.

2. Cut the charge tube and let compressor’s coolant out off the compressor about 1 minute.

3. Blow gas 2 joints, and remove the lter driers from the condenser ass’y and the capillary tube.

4. Now the lter driers is free.

REMOVE OF FILTER DRIERS

Condenser ass’y

Capillary tube

Filter driers

Capillary tube

Joint

Condenser ass’y

Charge tube

Compressor

Fig. 14

1. Remove the panel B-A and faucet ass’y in accordance with “REMOVE OF PANEL B-A” AND FAUCET ASS’Y”.

2. Cut the charge tube and let compressor’s coolant out off the compressor about 1 minute.

3. Disconnect 2 lead wires terminal of the compressor.

4. Remove the insulating seal cork tape and push up the cooling coil insulation tube.

5. Blow gas joint the cooling coil and joint the condenser ass’y to the compressor.

6. Remove 4 screws holding the compressor to the stand.

7. Now the compressor is free.

REMOVE OF COMPRESSOR

Cooling coil

Cooling coil insulation tube

Stand

Screw

Condenser ass’y

Joint

Compressor

Condenser ass’y

Insulating seal cork tape

Fig. 15

Page 14

TROUBLESHOOTING

Problem Possible Cause Corrective Action

1. No voltage received by water

dispenser.

2. Faulty wires.

3. Faulty starting relay.

4. Faulty compressor overload.

5. Faulty compressor.

No cold water and compressor not

running.

1. Plugged into the outlet.

2. Repaired or replaced power

cord ass’y.

3. Replaced starting relay.

4. Replaced compressor

over load.

5. Replaced compressor.

No cold water and compressor running.

1. Faulty a refrigerant leak.

2. Faulty a restriction in capillary

line or strainer.

3. Faulty compressor.

1. Repaired or replaced parts

involved with refrigerant

system.

2. Repaired or replaced capillary

line or strainer.

3. Replace compressor.

Unit runs noisily.

1. Faulty vibrations caused by loose

screws.

2. Faulty vibrations at refrigeration

lines.

3. Faulty compressor.

1. Turned screws to t.

2. Fitted refrigeration lines.

3. Repaired or replaced

compressor.

Water leaks.

1. Faulty cracked plastic bottle.

2. Faulty damaged reservoir.

3. Faulty loose faucet or damaged

gasket.

1. Replaced plastic bottle.

2. Repaired or replaced reservoir.

3. Repaired or replaced faucet

and gasket.

Oil on refrigerant lines.

1. Unplug service cord and

contact refrigeration

repairman.

1. Replaced plastic bottle.

2. Decrease the water to remain

a half.

1. Replaced heater tank.

2. Repaired space tank.

1. Replace.

2. Repair.

1. Repair.

2. Replace.

1. Repaired PCB Hot display.

1. Faulty cracked plastic bottle.

2. Turn over the bottle when the

tank cooler is ll.

1. Faulty heater tank leak.

2. Faulty space tank to crack.

1. Disconnection in heating circuit.

2. Erroneous wiring.

1. Erroneous wiring.

2. Poor operation.

1. Faulty PCB Hot display.

Water overow from tank cooler.

Hot water leaks.

Water temperature is kept low.

Boiling continue

Hot indicator lamp lights up all time.

Page 15

REF. NO

PARTS CODE

DESCRIPTION Q’TY PRICE

(FEC)

PRINTING & PACKAGING MATERIAL

1-1 31B101 INSTRUCTION BOOK 1 1-2 31B102 CARTON BOX 1 1-3 31B103 SHARP BADGE 1 1-4 31B104 NAME PLATE 1 1-5 31A1051 POP WATER DISPENSER 1 1-6 31B107 BOTTLE STICKER 1 1-7 31A108 WARNING STICKER 1 1-8 31B109 HOT WATER STICKER 1

1-9 31B118 INSTRUCTION STICKER 1 1-10 31A112L UPPER PAD FOAM-L 1 1-11 31A112R UPPER PAD FOAM-R 1 1-12 31B114 UNDER PAD FOAM 1

MECHANICAL PARTS

2-1 31A202 BOTTLE CONNECTOR 1

2-2 31B203 TOP PLATE 1

2-3 31B512 TANK RUBBER SEAL 1

2-4 31B220 WATER PARTITION 1

2-5 31B301SET TANK COOLER SET 1

2-5-1 31B301 TANK COOLER 1 2-5-2 31A302 THERMO PLATE 1 2-5-3 31B217 FAUCET CONNECTOR 1 2-5-4 3C108 BELLOW CAP PACKING 1 2-5-5 31B224ASY TANK CONNECTOR AS’Y 1 2-5-6 31B303 COOLING COIL 1 2-5-7 31B115 INSULATION FOAM 1 2-5-8 31B3051 TANK SUPPORT 1 2-5-9 31A704 COOLING COIL INSULATION TUBE 1

2-5-10 31A2181 MOUNTING NUT 2

2-6 31B230 SPACE TANK 1

2-7 31B518 SILICONE TUBE L = 380 mm. 1

2-8 31B334 CLAMP-9 for SILICONE TUBE 1

2-9 31B510 COOL WATER OUTLET TUBE 1 2-10 31B509 HOT WATER OUTLET TUBE 1 2-11 31B508 HOT WATER INLET TUBE 1 2-12 31B322ASY HEATER TANK AS’Y 1 2-13 31B511 DRAIN TUBE L = 300 mm. 1 2-14 31B222 DRAIN VALVE JOINT 1 2-15 31B312 BACK PLATE 1 2-16 31B514 O-RING (ID) 5.5*1.5 mm. 1 2-17 31B223 DRAIN VALVE CAP 1 2-18 31B307 CONDENSER AS’Y 1 2-19 31B332 SWITCH FIXING PLATE 1 2-20 31B308 THERMO FIXING PLATE 1 2-21 31B3101 SIDE PLATE-R 1 2-22 31B3091 SIDE PLATE-L 1 2-23 31A311 SIDE PLATE REINFORCE 2

2-24 31B204B PANEL-B 1

2-25 31B204A PANEL-A 1

2-26 31B214 PANEL SWITCH 1

2-27 31B205 FAUCET COVER 1

2-28 31B206 DRAIN TRAY SUPPORT 1

2-29 31B207 DRAIN TRAY 1

2-30 31B208CSET COOL FAUCET SET 1

SERVICE PARTS LIST

SB-29

Page 16

REF. NO

PARTS CODE

DESCRIPTION Q’TY PRICE

(FEC)

MECHANICAL PARTS

2-30-1 31B209 FAUCET BODY 1

2-30-2 31B506 RUBBER VALVE 1

2-30-3 31B213 PIN VALVE 1

2-30-4 31B313 SPRING VALVE 1

2-30-5 31B211 CAP VALVE 1

2-30-6 31B208 LEVER FAUCET 1

2-30-7 31B516 O-RING (ID) 10.8*2.4 mm. 1

2-30-8 31B210 FAUCET MOUNTING PLATE 1

2-30-9 31B212 CONNECTOR PIPE 1

2-31 31B208HSET HOT FAUCET SET 1

2-31-1 31B209HASY HOT FAUCET BODY AS’Y 1

MECHANICAL PARTS

2-32 31B216 STAND 1

2-33 31A219 TERMINAL COVER 1

2-34 31A320 COVER STRAP 1

2-35 31A502 GROMMET 4

2-36 31A316 SLEEVE GROMMET 4

2-37 31A321 WASHER FLAT 4

ELECTRIC PARTS

3-1 31B404ASY POWER CORD WITH PLUG 1

3-2 31B401SET COMPRESSOR SET 1

3-2-1 31B401 COMPRESSOR 1

3-2-2 31A4021 PTC RELAY 1

3-2-3 31A407 THERMO MOTOR 1

3-3 31B405SET HEATER SET 1

3-4 31B4061 SWITCH ON/OFF 1

3-5 31A403 THERMOSTAT 250V, 3A 1

3-6 31A306 FILTER DRIERS 1

3-7 31B413 THERMOSTAT 42oC 1

3-8 3G2131 THERMOSTAT 93oC 1

3-9 31B412 TEMP. FUSE AS’Y 1

3-10 31B408 PCB HOT DISPLAY 1

3-11 31B407 PCB COOL DISPLAY 1

3-12 E03B2000XG EARTH WIRE 1

3-13 31B409 FUSE AS’Y 1

3-14 31B410 L-WIRE for SWITCH ON/OFF {Thermostat 42oC + Sw. On/Off} 1

FIXING PARTS

4-1 122G0645 SCREW TAP P-PH+BT Zn-CR3+ M6*45 4

4-2 9A603 MOTOR SPACER WASHER 2

Page 17

REF. NO

PARTS CODE

DESCRIPTION Q’TY PRICE

(FEC)

PRINTING & PACKAGING MATERIAL

1-1 31B101 INSTRUCTION BOOK 1

1-2 31F102 CARTON BOX 1

1-3 31F103 SHARP BADGE 1

1-4 31F104 NAME PLATE 1

1-5 31A1051 POP WATER DISPENSER 1

1-6 31B107 BOTTLE STICKER 1

1-7 31A108 WARNING STICKER 1

1-8 31B109 HOT WATER STICKER 1

1-9 31B118 INSTRUCTION STICKER 1

1-10 31A112 UPPER PAD FOAM 1

1-11 31A114 UNDER PAD FOAM 1

MECHANICAL PARTS

2-1 31A202 BOTTLE CONNECTOR 1

2-2 31B203 TOP PLATE 1

2-3 31B512 TANK RUBBER SEAL 1

2-4 31B220 WATER PARTITION 1

2-5 31B301SET TANK COOLER SET 1

2-5-1 31B301 TANK COOLER 1

2-5-2 31A302 THERMO PLATE 1

2-5-3 31B217 FAUCET CONNECTOR 1

2-5-4 3C108 BELLOW CAP PACKING 1

2-5-5 31B224ASY TANK CONNECTOR AS’Y 1

2-5-6 31B303 COOLING COIL 1

2-5-7 31B115 INSULATION FOAM 1

2-5-8 31B3051 TANK SUPPORT 1

2-5-9 31A704 COOLING COIL INSULATION TUBE 1

2-5-10 31A2181 MOUNTING NUT 2

2-6 31B230 SPACE TANK 1

2-7 31B518 SILICONE TUBE L = 380 mm. 1

2-8 31B334 CLAMP-9 for SILICONE TUBE 1

2-9 31B510 COOL WATER OUTLET TUBE 1

2-10 31B509 HOT WATER OUTLET TUBE 1

2-11 31B508 HOT WATER INLET TUBE 1

2-12 31B322ASY HEATER TANK AS’Y 1

2-13 31B511 DRAIN TUBE L = 300 mm. 1

2-14 31B222 DRAIN VALVE JOINT 1

2-15 31B312 BACK PLATE 1

2-16

31B514 O-RING (ID) 5.5*1.5 mm. 1

2-17 31B223 DRAIN VALVE CAP 1

2-18 31B307 CONDENSER AS’Y 1

2-19 31B332 SWITCH FIXING PLATE 1

2-20 31B308 THERMO FIXING PLATE 1

2-21 31B3101 SIDE PLATE-R 1

2-22 31B3091 SIDE PLATE-L 1

2-23 31A311 SIDE PLATE REINFORCE 2

2-24 31B204B PANEL-B 1

SB-29S

Page 18

REF. NO

PARTS CODE

DESCRIPTION Q’TY PRICE

(FEC)

MECHANICAL PARTS

2-25 31B204A PANEL-A 1

2-26 31B214 PANEL SWITCH 1

2-27 31B205 FAUCET COVER 1

2-28 31B206 DRAIN TRAY SUPPORT 1

2-29 31B207 DRAIN TRAY 1

2-30 31B208CSET COOL FAUCET SET 1

2-30-1 31B209 FAUCET BODY 1

2-30-2 31B506 RUBBER VALVE 1

2-30-3 31B213 PIN VALVE 1

2-30-4 31B313 SPRING VALVE 1

2-30-5 31B211 CAP VALVE 1

2-30-6 31B208 LEVER FAUCET 1

2-30-7 31B516 O-RING (ID) 10.8*2.4 mm. 1

2-30-8 31B210 FAUCET MOUNTING PLATE 1

2-30-9 31B212 CONNECTOR PIPE 1

2-31 31B208HSET HOT FAUCET SET 1

2-31-1 31B209HASY HOT FAUCET BODY AS’Y 1

2-32 31F216 STAND 1

2-33 31A219 TERMINAL COVER 1

2-34 31A320 COVER STRAP 1

2-35 31A502 GROMMET 4

2-36 31A316 SLEEVE GROMMET 4

2-37 31A321 WASHER FLAT 4

ELECTRIC PARTS

3-1 31B404ASY POWER CORD WITH PLUG 1

3-2 31B401SET COMPRESSOR SET 1

3-2-1 31B401 COMPRESSOR 1

3-2-2 31A4021 PTC RELAY 1

3-2-3 31A407 THERMO MOTOR 1

3-3 31B405SET HEATER SET 1

3-4 31B4061 SWITCH ON/OFF 1

3-5 31A403 THERMOSTAT 250V, 3A 1

3-6 31A306 FILTER DRIERS 1

3-7 31B413 THERMOSTAT 42oC 1

3-8 3G2131 THERMOSTAT 93oC 1

3-9 31B412 TEMP. FUSE AS’Y 1

3-10 31B408 PCB HOT DISPLAY 1

3-11 31B407 PCB COOL DISPLAY 1

3-12 E03B2000XG EARTH WIRE 1

3-13 31B409 FUSE AS’Y 1

3-14 31B410 L-WIRE for SWITCH ON/OFF {Thermostat 42oC + Sw. On/Off} 1

FIXING PARTS

4-1 122G0645 SCREW TAP P-PH+BT Zn-CR3+ M6*45 4

4-2 9A603 MOTOR SPACER WASHER 2

Page 19