Sharp S3B, 5BS- A, 4BS-A Service Manual
CTV990504
Month of Issue: May 1999
Classification: White
TELEVISION TECHNICAL BULLETIN
Page 1 of 7
MODELS BCTVA Chassis 4BS-C Chassis CA1 Chassis CA10 Chassis
CW100 Chassis CS Chassis D3000 Chassis DECO-4 Chassis
DECO-5 Chassis 4BS-B Chassis 4BS-A Chassis 5BS- A Chassis
S3B Chassis
To assist with the adjustments of the above chassis, the list below details how to enter the various
service modes.
BCTVA Chassis
66AS06H, DV5932H, DV5935H, DV5937H and DV6635H
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode
Sharp Electronics (UK) Limited
Reference
White – Carry out as required, Yellow – Carry out as required and whenever the unit comes in for service, Red – Carry out on all units
AVW060599/1
Revision
1
CTV990504
Month of Issue: May 1999
Classification: White
TELEVISION TECHNICAL BULLETIN
4BS-C Chassis
DV5940H, DV6640H and 66AS05H
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Text Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire
Page 2 of 7
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
CA1 Chassis
37DM23H, 37DT25H, 37ET35H, 37EM33H and 51DT25H
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off
To exit the service mode, press the standby button on the remote control.
Sharp Electronics (UK) Limited
Reference
White – Carry out as required, Yellow – Carry out as required and whenever the unit comes in for service, Red – Carry out on all units
AVW060599/1
Revision
1
CTV990504
Month of Issue: May 1999
Classification: White
TELEVISION TECHNICAL BULLETIN
Page 3 of 7
CA10 Chassis
51DS02H, 51DS03H, 51DS05H, 59DS03H, 59DS05H, 59ES03H, 59ES05H, 59ESD7H, 66DS03H, 66DS05H,
66ES05H and 66ESD7H
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
CS Chassis
51CS03H, 51CS05H, 59CS03H, 59CS05H, 59CSD8H, 66CS03H, 66CS05H and 66CSD8H
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
CW100 Chassis
66DW18H and 76DW18H
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp Electronics (UK) Limited
Reference
White – Carry out as required, Yellow – Carry out as required and whenever the unit comes in for service, Red – Carry out on all units
AVW060599/1
Revision
1
Loading...