Page 1
Professional SLIM
STEAM POCKET® MOP
S3455UKE
OWNER’S GUIDE
Page 2
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WHEN USING YOUR SHARK® STEAM MOP,
BASIC SAFETY PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED, INCLUDING THE
FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING
YOUR SHARK
DANGER OF SCALDING.
®
STEAM MOP.
Please use caution when using the steam mop. The
steam emitted from the steam mop is very hot.
IM P ORTANT:
This appliance is not intended for use by persons with
reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been
given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children shall not use or play with this appliance. Close
supervision is necessary to keep appliance out of reach of
children during use and cooling.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY:
1 Use the system only for its intended use.
2 DO NOT use outdoors.
3 DO NOT leave the appliance unattended when
plugged in. Always unplug the power cord from the
electrical outlet when not in use and before servicing.
4 DO NOT allow the appliance to be used by children.
Close attention is necessary when used near
children, pets or plants.
5 Use only as described in this manual.
6 Use only manufacturer’s recommended accessories.
7 DO NOT use with damaged cord or plug.
8 DO NOT USE if the appliance is not working, has
been dropped, dropped into water, damaged or
left outdoors.
9 NO SERVICEABLE PARTS. Incorrect re-assembly
or repair can cause a risk of electrical shock or injury
to persons when the appliance is used. Contact
Customer Service.
10 To protect against a risk of electric shock, DO NOT
immerse the steam mop into water or any other liquids.
11 DO NOT handle plug or steam mop with wet hands
or operate appliance without shoes.
12 DO NOT pull or carry by power cord, use power cord
as handle, close a door on the power cord, or pull
the power cord around sharp edges or corners. Keep
power cord away from heated surfaces.
13 DO NOT unplug by pulling on power cord. To unplug,
grasp the plug not the power cord. Do not use
extension cords or outlets with inadequate current
carrying capacity.
14 DO NOT put any objects into openings. Do not use
with any opening that is blocked.
15 DO NOT put hands or feet under the steam mop. Unit
gets very hot.
16 Use ONLY on flat, horizontal surfaces. Do not use on
walls, counters or windows.
17 DO NOT use on leather, wax polished furniture or
floors, synthetic fabrics, velvet or other delicate,
steam sensitive materials.
18 Liquid or steam must not be directed towards
equipment containing electrical components, such as
the interior of ovens.
19 DO NOT add cleaning solutions, scented perfumes,
oils or any other chemicals to the water used in this
appliance as this may damage the unit or make it
unsafe for use. If you live in a hard water area, we
recommend using distilled water in your steam mop.
20 When in use, NEVER turn the appliance over or
on its side. NEVER DIRECT STEAM TOWARDS
PEOPLE, ANIMALS OR PLANTS.
21 NEVER LEAVE THE STEAM MOP IN ONE SPOT
ON ANY SURFACE FOR ANY PERIOD OF TIME
WHEN THE CLEANING POCKET IS ATTACHED AS
THIS WILL DAMAGE YOUR FLOORS.
22 Carefully remove the cleaning pocket immediately
after you have unplugged and allowed the steam
mop to cool.
23 When cleaning the steam mop, unplug the power
cord from the electrical outlet and clean with a dry
or damp cloth. Do not pour water or use alcohol,
benzene or paint thinner on the unit.
24 Extreme caution should be exercised when using this
appliance to clean stairs.
25 Never use steam mop without the cleaning pocket
attached.
26 Keep your work area well lit.
27 Store steam mop indoors in a cool, dry place.
28 To avoid circuit overload, do not operate another
appliance on the same socket (circuit) as the steam
cleaner.
29 If an extension cord is absolutely necessary, an
extension cord rated a minimum of 15 ampere,
2
(14 AWG) cord should be used. Cords rated
2.08mm
for less amperage may overheat. Care should be
taken to arrange cord so that it cannot be pulled or
tripped over.
30 DO NOT leave unattended when the system is
connected to a power supply or electrical outlet. Turn
off all controls before unplugging the unit.
31 DO NOT store unit with damp or wet cleaning pocket
attached. Never leave the steam mop in one spot on
any surface for any period of time with a damp or wet
cleaning pocket attached as this will damage your
floors.
32 Always unplug and allow the steam mop to cool
before removing or changing mop heads.
33 Make sure that the water tank door is closed when
using the appliance.
WARNING: Your steam mop is designed
to clean hard floor surfaces that will withstand high
heat. Do not use on unsealed wood or unglazed
ceramic floors. On surfaces that have been treated
with wax or some no wax floors, the sheen may
be removed by the heat and steam action. It is
always recommended to test an isolated area of
the surface to be cleaned before proceeding. We
also recommend that you check the use and care
instructions from the floor manufacturer.
SAVE THESE
INSTRUCTIONS
www.sharkclean.eu/ukFreephone: 0 800 8 62 04 53
Page 3
Contents
IPX4
IPX4
This appliance complies with the WEEE-Directive 2012/96/EC on the disposal of electrical and electronic equipment
(WEEE).
This marking indicates that this product should not be disposed with other household wastes
throughout the EU. To prevent possible harm to the environment or human health from uncontrolled
waste disposal, recycle it responsibly to promote the sustainable reuse of material sources. To return
your used device, please use the return and collection systems or contact the retailer where this
product was purchased. They can take this product for environmental safe recycling.
This appliance complies with the European directives for electromagnetic compatibility (EMC) 2004/108/EC and its
revisions, as well as Low Voltage Directive (LVD) 2006/95/EC and its revisions.
This product has no on/off switch and operates when plugged into the main supply source. Disconnect the plug from
mains after use.
Although the product is not provided with standby mode or off mode, it still fulfills the requirements of 1275/2008/
EC - the directive for Eco-Design requirements since according to technical justification, it is considered as
inappropriate to provide standby and off modes when connecting to mains. To reduce energy consumption be sure to
unplug the unit after use.
Thank you for
purchasing the
®
Shark
Professional
SLIM Steam
®
Pocket
Mop.
Getting Started ....................................................................................... 2
Using Your Steam Mop ............................................................................ 5
Care of Your Steam Mop .......................................................................... 8
Troubleshooting Guide ............................................................................. 10
This manual covers model:
S3455UKE 11
TECHNICAL SPECIFICATIONS
Voltage: 220-240V~, 50/60Hz
Power: 1550W
Water Capacity: 300 ml
Euro-Pro, Shark and Steam Pocket are trademarks of
Euro-Pro Operating LLC. All other brand names may be
trademarks of their respective owners.
1www.sharkclean.eu/ukFreephone: 0 800 8 62 04 53
Page 4
Getting Started
When assembling your steam mop there may be a little
water in or around the water tank. This is because we test
all our steam mops 100% before you buy them, so you get
a quality Shark
®
Professional SLIM Steam Pocket® Mop.
c
j
k
a
b
d
e
h
f
i
g
a Steam Mop Body
b Mop Handle
c Triangle Mop Head
(1025SO)
d Cleaning Pocket for the Triangle Mop Head (P 140W )
e All-Purpose Mop Head (10 24SOY )
f Cleaning Pocket for the All-Purpose Mop Head
(P 129W )
g Carpet Glider (XCG2 00)
h Water Flask (1039SO)
i (1) 6mm x 52mm Large Screw*
* Phillips or flat head screwdriver can be used.
Screwdriver not included.
l
m
j Quick Release Swivel Cord Wrap
k Cord Clip
l Water Tank
m Steam Control Button
n Mop Head Release Button
n
fig. 1
ASSEMBLE
I MPOR TA NT: Always make sure the mop is
UNPLUGGED from the wall when not in use.
Never fill the mop, attach the mop head, change
or remove the cleaning pocket when the mop is
plugged into the wall. To prolong the life of your
Shark® Professional SLIM Steam Pocket® Mop,
we recommend using distilled water. Make sure you
only add water to the tank. Chemicals or cleaning
1 Insert the Mop handle end labeled “Front” into
the steam mop body. Make sure it is inserted past
the line printed on the pole. Secure the assembled
handle and pole by using the large screw and a
Phillips or a flat head screwdriver (screwdriver not
included). (fig. 1)
solution may damage the appliance and could be
unsafe for you and your family.
2 3www.sharkclean.eu/ukFreephone: 0 800 8 62 04 53
Page 5
Getting Started - cont’d
Using Your Steam Mop
IM POR TA N T: Do not use the mop without attaching
a cleaning pocket and adding water to the tank first.
When you are using the mop for the first time, it
might take longer than the normal 30 seconds to
start steaming.
fig. 2
fig. 3
2 Select either the All-Purpose Mop Head or the
Triangle Mop Head and accompanying cleaning pad.
Use the loop on the side of the cleaning pad to slide
the mop head into the pad pocket. Then secure the
quick fasteners on the top of the pocket to lock in
place. (fig. 2)
3 Snap the mop head into the base to secure it. (fig. 3)
4 Open the water tank door. (fig. 4)
Use the filling flask and pour water into the tank. Do
not overfill. Press the water tank door firmly to close.
(fig. 5)
fig. 4
fig. 5
I MPOR TA NT: Do not use on unsealed wood or
unglazed ceramic floors. On surfaces that have
been treated with wax or some no wax floors, the
sheen may be removed by the heat and steam
action. It is always recommended to test an isolated
area of the surface to be cleaned before proceeding.
We recommend that you check the use and care
instructions from the floor manufacturer.
fig. 6
IMP O RTANT: Sweep or vacuum your floors prior to
cleaning with your Steam Mop.
m
a
e
t
s
l
o
r
t
n
o
c
fig. 7
1 Pull and twist the quick release cord holder to
unwrap the power cord completely. Plug into an
electrical outlet. (fig. 6)
2 The STEAM CONTROL button will flash blue. If the
light does not turn on, reference the troubleshooting
section on page 10. (fig. 7)
4 5www.sharkclean.eu/ukFreephone: 0 800 8 62 04 53
Page 6
Using Your Steam Mop - cont’d
m
a
te
s
l
o
r
t
n
o
c
fig. 8
Using Your Carpet Glider
The Steam Mop will not clean your
carpeting or area rugs. However, it is
great for grooming andfreshening.
fig. 11
fig. 12
fig. 10
3 Press the STEAM CONTROL button once to activate
the LOW steam setting.
Press the STEAM CONTROL button twice to
activate the HIGH steam setting. (fig. 8)
Use the scrubbing side of the cleaning pockets when
using the HIGH steam setting.
4 Clean your floors with a forward and backward
motion. (fig. 9)
To stop the steam, press the STEAM CONTROL
button a third time.
The STEAM CONTROL button will flash blue to
indicate the mop is in STA NDBY mode.
6 7www.sharkclean.eu/ukFreephone: 0 800 8 62 04 53
fig. 9
5 When one side of the cleaning pocket gets dirty,
just flip the mop and you can quickly start using
the other side. Use the shaggy side of the cleaning
pockets to lift up and lock away all the dirt and
debris and the scrubbing side to break up the
tough stain. (fig. 10)
6 When the water tank is empty, the steam mop will
stop producing steam. You can refill the water tank
at any time as long as the mop is unplugged from the
outlet. Reference the filling instructions from page 4.
NOTE: Please wait 2-3 minutes for the Steam Mop
to cool off before removing the mop head or the
cleaning pocket. Never leave the steam mop with a
damp/wet cleaning pocket on any floor.
THE CARPET GLIDER
1 The Carpet Glider can be used with the All-Purpose
Head to lightly steam your carpet and area rugs. Just
place the mop head with the cleaning pocket attached
into the glider. The recommended steam setting is
HIGH when using the Carpet Glider. (fig . 11)
2 Move the Steam Mop back and forth across a
section of the carpet. ( fig . 12)
Page 7
Care of Your Steam Mop
fig. 18
fig. 13
fig . 14
AFTER USE AND STORAGE
1 When you have finished using the steam mop, press
the STEAM CONTROL button until the LED light turns
flashing BLUE. This stops the unit from steaming.
Unplug the cord from the outlet and place the mop into
the upright position. Let the unit cool for 2-3 minutes.
Remove the cleaning pocket by releasing the quick
fasteners and using the lavender loop on the side of
the pocket, avoiding contact with the hot pocket or
dirt. (fig. 13)
fig. 15
2 Empty the water tank before storage. Open the water
tank door and empty the tank over a sink. Close the
water cap. (fig. 14)
3 To store the Shark
Pocket
®
®
Professional SLIM Steam
Mop hanging up, first remove the head (after
it has cooled and the steam has been released) then
hang on a large hook. (fig. 15)
fig. 16
fig. 17
CARE OF YOUR CLEANING POCKET
1 We recommend washing your cleaning pocket
separately from other fabrics to avoid picking
up lint. Only use liquid detergent (no powder
detergent). Do not use any fabric softeners or
bleach. For optimal cleaning performance pockets
may need to be washed up to (3) three times. Line
dry. Do not tumble dry. (fig. 16)
2 If there are loose threads on the cleaning pocket
carefully cut the thread with scissors. Do not pull on
them or cut at the base. (fi g. 17)
ORDERING REPLACEMENT PARTS
To order additional parts and accessories, feel free to
contact us at:
Shark Customer Services
15 Mariner Court
Calder Park
Wakefield
WF4 3FL
Freephone 0800 862 0453
www.sharkclean.eu
DECALCIFYING YOUR STEAM MOP
Calcium and mineral deposits can build up and impact
the performance of your steam mop over time.
CLEANING THE NOZZLE
Your steam mop should not normally require
cleaning, however, should you notice a decrease in
the steam output, it may be necessary to remove
mineral deposits built up around the nozzle.
1 Unplug the steam mop from the electrical outlet.
2 Use a small diameter stiff metal wire, such as a
straightened metal paperclip, and carefully insert the
end of the wire into the nozzle orifice. (fi g. 18)
3 Move the wire back and forth several times to
remove any deposits.
4 Plug the steam mop in to the power outlet and test
steam output.
PART PART NO.
1 Cleaning Pockets XTSM200UK
2 Triangle Pads STT3901UKJR
3 Carpet Glider XCG3501UK
8 9www.sharkclean.eu/ukFreephone: 0 800 8 62 04 53
Page 8
Troubleshooting Guide
PROBLEM POSSIBLE REASONS & SOLUTIONS
Notes
The Professional SLIM
Steam Pocket
®
Mop will not
turn-on.
The unit will not make
steam.
Cannot select steam
setting/flashing blue light
remains on.
The Professional SLIM
Steam Pocket® Mop leaves
water on the floor.
The Professional SLIM
Steam Pocket® Mop left a
white spot on the floor.
Floors are cloudy, streaky
or spotty after steaming.
Your steam mop should be securely plugged into an electrical outlet only.
Check your fuse or breaker.
If your unit still does not work, give us a call at: Freephone 0800 862 0453.
Is there water in the water tank? If not, add water to your steam mop following
instructions on page 4.
If the unit still doesn’t make steam, follow the decalcification instructions on page 9.
If you have already plugged in your unit, unplug and try a different outlet. This
may reset the Standby mode.
Add water to the tank and press the STEAM CONTROL button to select a
steam setting.
If your unit still does not work, call 0800 862 0453.
Check to see if your cleaning pocket is soaked through. We recommend you
unplug the steam mop and change the cleaning pocket.
Make sure the cleaning pocket is attached correctly.
Do not leave your steam mop on the floor with a damp or wet cleaning pocket.
If you’re using tap water we recommend switching to distilled water.
Make sure the cap is securely on the water tank.
The cleaning pocket might be dirty, change the cleaning pocket.
If you washed the cleaning pocket with powder detergent, then it might be ruined.
You might have left the mop in the same spot for too long. Do you have hard
water? If you do, you might want to switch to distilled water.
This might be leftover from past cleaners used on the floor surface. Use the
steam mop a few more times and see if the leftover cloudiness is removed. If
this does not work, we suggest rinsing the floor with water, letting it dry, and
then steam mopping again with a clean pocket. One or more rinses generally
removes the residue. A more stubborn case may require you to rinse the floor
with a mix of one part vinegar and two parts water.
The Professional SLIM
Steam Pocket® Mop is hard
to push.
10 11www.sharkclean.eu/ukFreephone: 0 800 8 62 04 53
Make sure the cleaning pocket is attached correctly.
Check to see if the cleaning pocket is excessively dirty. Replace if the cleaning
pocket is too dirty or wet.
Page 9
Euro-Pro Europe LTD
IPX4
IPX4
15 Mariner Court
Calder Park
Wakefield
WF4 3FL
Freephone 0800 862 0453
www.sharkclean.eu
Technical Details
Model number: S3455UKE 11
Input: 1550W
Main unit voltage: 220-240V~, 50/60 Hz
COPY RIGHT© EU RO-PRO OP ERATING L LC 2014
PRINTED IN CHINA
Euro- Pro, Shar k and Steam Po cket are tr ademarks of Euro -Pro Op erating
LLC. All other bra nd names ma y be tradem arks of th eir respe ctive ow ners.
S3 455U KE_11_ IB _E _150619 _7
Illustrations may differ from actual product.
Loading...