SHARP R402JKT, R-402JW-T Service Manual

Page 1
R402JWT
SERVICE MANUAL
S5601R402JPW/
MICROWAVE OVEN
MODELS
In the interest of user-safety the oven should be restored to its origi­nal condition and only parts identical to those specified should be used.
WARNING TO SERVICE PERSONNEL: Microwave ovens con­tain circuitry capable of producing very high voltage and cur­rent, contact with following parts may result in a severe, possibly fatal, electrical shock. (High Voltage Capacitor, High Voltage Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..)
CONTENTS
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPO­SURE TO EXCESSIVE MICROWAVE ENERGY CHAPTER 1. WARNING TO SERVICE PERSONNEL
BEFORE SERVICING
CHAPTER 2. MICROWAVE MEASUREMENT PRO­CEDURE
CHAPTER 3. FOREWORD AND WARNING
R-402JK-T R-402JW-T
CHAPTER 7. TROUBLESHOOTING GUIDE
CHAPTER 8. TEST PROCEDURES
CHAPTER 9. TOUCH CONTROL PANEL ASSEMBLY
CHAPTER 10. PRECAUTIONS FOR USING LEAD­FREE SOLDER
CHAPTER 11. COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE
CHAPTER 5. GENERAL INFORMATION
CHAPTER 6. OPERATION
SHARP CORPORATION
CHAPTER 12. CIRCUIT DIAGRAMS
Parts List
This document has been published to be used for after sales service only. The contents are subject to change without notice.
Page 2
CONTENTS
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPO­SURE TO EXCESSIVE MICROWAVE ENERGY
BEFORE SERVICING
CHAPTER 1. WARNING TO SERVICE PERSONNEL
[1] Before Servicing .........................................1-1
[2] When the testing is completed, ..................1-1
[3] After repairing .............................................1-1
CHAPTER 2. MICROWAVE MEASUREMENT PRO­CEDURE
[1] Requirements: ............................................2-1
[2] Preparation for testing: ...............................2-1
[3] Leakage test: ..............................................2-1
CHAPTER 3. FOREWORD AND WARNING
[1] FOREWORD ..............................................3-1
[2] WARNING ..................................................3-1
[3] DANGER ....................................................3-1
CHAPTER 4. PRODUCT DESCRIPTION
[1] SPECIFICATIONS ......................................4-1
CHAPTER 5. GENERAL INFORMATION
[1] GROUNDING INSTRUCTIONS .................5-1
[2] OVEN DIAGRAM........................................5-1
CHAPTER 6. OPERATION
[1] DESCRIPTION OF OPERATING SE-
QUENCE ...................................................6-1
[2] OVEN SCHEMATIC ...................................6-2
[3] DESCRIPTION AND FUNCTION OF
COMPONENTS..........................................6-3
CHAPTER 7. TROUBLESHOOTING GUIDE
[1] TROUBLESHOOTING CHART .................7-1
CHAPTER 8. TEST PROCEDURES
[1] Procedure A: MAGNETRON ASSEMBLY
TEST ..........................................................8-1
[2] Procedure B: POWER TRANSFORMER
TEST ..........................................................8-1
[3] Procedure C: HIGH VOLTAGE RECTIFI-
ER TEST ....................................................8-1
[4] Procedure D: HIGH VOLTAGE CAPACI-
TOR TEST..................................................8-2
[5] Procedure E: TEMPERATURE FUSE OR
THERMAL CUT-OUT TEST .......................8-2
[6] Procedure F: PRIMARY INTERLOCK
SWITCH TEST ...........................................8-2
[7] Procedure F: SECONDARY INTERLOCK
SYSTEM TEST...........................................8-3
[8] Procedure G: MONITOR SWITCH TEST.....8-3
[9] Procedure H: BLOWN MONITOR FUSE
TEST........................................................... 8-3
[10] Procedure I: NOISE FILTER TEST............. 8-4
[11] Procedure J: TOUCH CONTROL PANEL
ASSEMBLY TEST....................................... 8-4
[12] Procedure K: KEY UNIT TEST ................... 8-5
[13] Procedure L: RELAY TEST......................... 8-6
[14] Procedure M: DEFROST TEST.................. 8-6
[15] Procedure N: FOIL PATTERN ON THE
PRINTED WIRING BOARD TEST.............. 8-6
CHAPTER 9. TOUCH CONTROL PANEL ASSEM­BLY
[1] OUTLINE OF TOUCH CONTROL PANEL ..... 9-1
[2] DESCRIPTION OF LSI ............................... 9-1
[3] SERVICING FOR TOUCH CONTROL
PANEL ........................................................ 9-4
CHAPTER 10. PRECAUTIONS FOR USING LEAD­FREE SOLDER
[1] Employing lead-free solder ....................... 10-1
[2] Using lead-free wire solder ....................... 10-1
[3] Soldering................................................... 10-1
CHAPTER 11. COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE
[1] WARNINGS ...............................................11-1
[2] OUTER CASE REMOVAL .........................11-2
[3] POWER TRANSFORMER REMOVAL......11-2
[4] HIGH VOLTAGE RECTIFIER AND HIGH
VOLTAGE CAPACITOR REMOVAL ..........11-2
[5] MAGNETRON REMOVAL .........................11-2
[6] OVEN LAMP REMOVAL............................11-3
[7] POSITIVE LOCK CONNECTOR (NO-
CASE TYPE) REMOVAL .......................
[8] CONTROL PANEL ASSEMBLY REMOV-
AL ..............................................................11-3
[9] GRAPHIC SHEET AND MEMBRANE
SWITCH REPLACEMENT.........................11-3
[10] TURNTABLE MOTOR REMOVAL.............11-4
[11] COOLING FAN MOTOR REMOVAL..........11-4
[12] DOOR SENSING SWITCH/PRIMARY IN-
TERLOCK SWITCH AND MONITOR
SWITCH REMOVAL ..................................11-5
[13] DOOR SENSING SWITCH/PRIMARY IN-
TERLOCK SWITCH AND MONITOR
SWITCH ADJUSTMENT ...........................11-5
[14] DOOR REPLACEMENT ............................11-5
CHAPTER 12. CIRCUIT DIAGRAMS
[1] Pictorial Diagram (Figure S-1) .................. 12-1
[2] Control Panel Circuit (Figure S-2)............. 12-2
[3] Printed Wiring Board (Figure S-3) ............ 12-3
Parts List
....11-3
Page 3
R402JWT
R402JWT
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID
Service Manual
POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY

PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY

(a) Do not operate or allow the oven to be operated with the door open. (b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other
microwave source, and make repairs as necessary: (1) interlock operation, (2) proper door closing, (3) seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and latches, (5) evidence of dropping or abuse.
(c) Before turning on microwave power for any service test or inspection within the microwave generating
compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity, and connections.
(d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave
generation and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual before the oven is released to the owner.
(e) A microwave leakage check to verify compliance with the Federal Performance Standard should be
performed on each oven prior to release to the owner.
BEFOR SERVICING
BEFORE SERVICING
Before servicing an operative unit, perform a microwave emission check as per the Microwave Measurement Procedure outlined in this service manual. If microwave emissions level is in excess of the specified limit, contact SHARP ELECTRONICS CORPORATION immediately @1-800-237-4277.
If the unit operates with the door open, service person should 1) tell the user not to operate the oven and 2) contact SHARP ELECTRONICS CORPORATION and Food and Drug Administration's Center for Devices and Radiological Health immediately.
Service personnel should inform SHARP ELECTRONICS CORPORATION of any certified unit found with emissions in excess of 4mW/cm . The owner of the unit should be instructed not to use the unit until the oven has been brought into compliance.
2
i
Page 4
R402JWT
R402JWT

CHAPTER 1. WARNING TO SERVICE PERSONNEL

Microwave ovens contain circuitry capable of producing very high voltage and current, contact with following parts may result in a severe, possibly fatal, electrical shock.
(Example)
High Voltage Capacitor, High Voltage Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..
Read the Service Manual carefully and follow all instructions.
Service Manual
Don't Touch !
Danger High Voltage

[1] Before Servicing

1. Disconnect the power supply cord , and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
WARNING: RISK OF ELECTRIC SHOCK. DISCHARGE THE HIGH-
VOLTAGE CAPACITOR BEFORE SERVICING.
The high-voltage capacitor remains charged about 60 seconds after the oven has been switched off. Wait for 60 seconds and then short-circuit the connection of the high-voltage capacitor (that is the connecting lead of the high-voltage rectifier) against the chassis with the use of an insulated screwdriver.
Whenever troubleshooting is performed the power supply must be dis­connected. It may, in some cases, be necessary to connect the power supply after the outer case has been removed, in this event,
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) 4.Disconnect the leads to the primary of the power transformer.
5) Ensure that the leads remain isolated from other components and oven chassis by using insulation tape.
6) After that procedure, reconnect the power supply cord.

[2] When the testing is completed,

1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Reconnect the leads to the primary of the power transformer.
5. Reinstall the outer case (cabinet).
6. Reconnect the power supply cord after the outer case is installed.
7. Run the oven and check all functions.

[3] After repairing

1. Reconnect all leads removed from components during testing.
2. Reinstall the outer case (cabinet).
3. Reconnect the power supply cord after the outer case is installed.
4. Run the oven and check all functions.
Microwave ovens should not be run empty. To test for the presence of microwave energy within a cavity, place a cup of cold water on the oven turntable, close the door and set the power to HIGH and set the microwave timer for two (2) minutes. When the two minutes has elapsed (timer at zero) carefully check that the water is now hot. If the water remains cold carry out Before Servicing procedure and re­examine the connections to the component being tested.
When all service work is completed and the oven is fully assembled, the microwave power output should be checked and microwave leak­age test should be carried out.
1 – 1
Page 5
R402JWT
R402JWT

CHAPTER 2. MICROWAVE MEASUREMENT PROCEDURE

Service Manual

[1] Requirements:

1. Microwave leakage limit (Power density limit): The power density of microwave radiation emitted by a microwave oven should not exceed 1mW/
2
cm
at any point 5cm or more from the external surface of the oven, measured prior to acquisition by a purchaser, and thereafter (through the use-
ful life of the oven), 5 mW/cm
2. Safety interlock switches:
Primary interlock switch shall prevent microwave radiation emission in excess of the requirement as above mentioned. Secondary interlock relay and door sensing switch shall prevent microwave radiation emission in excess of 5 mW/cm the oven.
2
at any point 5cm or more from the external surface of the oven.
2
at any point 5cm or more from the external surface of

[2] Preparation for testing:

Before beginning the actual measurement of leakage, proceed as follows:
1. Make sure that the actual instrument is operating normally as specified in its instruction booklet.
Important:
Survey instruments that comply with the requirement for instrumentation as prescribed by the performance standard for microwave ovens, 21 CFR
1030.10(c)(3)(i), must be used for testing.
2. Place the oven tray in the oven cavity.
3. Place the load of 275±5 ml (9.8 oz) of tap water initially at 20±5°C (68°F) in the center of the oven cavity.
The water container shall be a low form of 600 ml (20 oz) beaker with an inside diameter of approx. 8.5 cm (3-1/2 in.) and made of an electrically nonconductive material such as glass or plastic.
The placing of this standard load in the oven is important not only to protect the oven, but also to insure that any leakage is measured accurately.
4. Set the cooking control on Full Power Cooking Mode
5. Close the door and select a cook cycle of several minutes. If the water begins to boil before the survey is completed, replace it with 275 ml of cool water.

[3] Leakage test:

Closed-door leakage test (microwave measurement)
1. Grasp the probe of the survey instrument and hold it perpendicular to the gap between the door and the body of the oven.
2. Move the probe slowly, not faster than 1 in./sec. (2.5 cm/sec.) along the gap, watching for the maximum indication on the meter.
3. Check for leakage at the door screen, sheet metal seams and other accessible positions where the continuity of the metal has been breached (eg., around the switches, indicator, and vents).
While testing for leakage around the door pull the door away from the front of the oven as far as is permitted by the closed latch assembly.
2
4. Measure carefully at the point of highest leakage and make sure that the highest leakage is no greater than 4mW/cm interlock relay and the primary interlock switch do turn the oven OFF before any door movement.
NOTE: After servicing, record data on service invoice and microwave leakage report.
, and that the secondary
2 – 1
Page 6
R402JWT
R402JWT

CHAPTER 3. FOREWORD AND WARNING

Service Manual

[1] FOREWORD

This Manual has been prepared to provide Sharp Electronics Corp. Service Personnel with Operation and Service Information for the SHARP MICROWAVE OVEN, R-402JK-T and R-402JW-T.
It is recommended that service personnel carefully study the entire text of this manual so that they will be qualified to render satisfactory customer service.
Check the interlock switches and the door seal carefully. Special attention should be given to avoid electrical shock and microwave radiation hazard.

[2] WARNING

Never operate the oven until the following points are ensured.
(A) The door is tightly closed.
(B) The door brackets and hinges are not defective.
(C) The door packing is not damaged.
(D) The door is not deformed or warped.
(E) There is no other visible damage with the oven.
Servicing and repair work must be carried out only by trained service personnel.

[3] DANGER

Certain initial parts are intentionally not grounded and present a risk of electrical shock only during servicing. Service personnel - Do not contact the following parts while the appliance is energized;
High Voltage Capacitor, Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness;
If provided, Vent Hood, Fan assembly, Cooling Fan Motor.
All the parts marked “ “ on parts list are used at voltages more than 250V.
Removal of the outer wrap gives access to voltage above 250V.
All the parts marked “*“on parts list may cause undue microwave exposure, by themselves, or when they are damaged, loosened or removed.
3 – 1
Page 7
R402JWT

CHAPTER 4. PRODUCT DESCRIPTION

Service Manual

[1] SPECIFICATIONS

ITEM DESCRIPTION
Power Requirements
Power Consumption 1600W / Approx. 13.5 Amperes
Power Output
Outside Dimensions
Cooking Cavity Dimensions (1.4 Cubic feet)
Control Complement
120 Volts 60 Hertz Single phase, 3 wire grounded
1100 W nominal of RF microwave energy (IEC Test procedure) Operating frequency 2450 MHz
Width 21-5/8" (550mm) Height 12-3/8" (315mm) Depth 17-7/8" (453mm)
Width 15-3/8" (392mm) NOTE: Internal capacity is calculated by measuring Height 9-3/8" (236.7mm) maximum width, depth and height. Depth 16-3/4" (426.5mm) Actual capacity for holding food is less.
Touch Control System Clock (1:00 - 12:59) Timer (0 - 99 minutes 99 seconds) Microwave Power for Variable Cooking
Repetition Rate; P-HI -------------------- Full power throughout the cooking time P-90 -------------------- approx. 90% of FULL Power P-80 -------------------- approx. 80% of FULL Power P-70 -------------------- approx. 70% of FULL Power P-60 -------------------- approx. 60% of FULL Power P-50 -------------------- approx. 50% of FULL Power P-40 -------------------- approx. 30% of FULL Power P-30 -------------------- approx. 40% of FULL Power P-20 -------------------- approx. 20% of FULL Power P-10 -------------------- approx. 10% of FULL Power P-0 ---------------------- No power throughout the cooking time
R402JWT
POPCORN pad NIGHT LIGHT pad MINUTE PLUS pad Cook pad Defrost pad Reheat pad Number selection pads Power Level pad Timer/Clock pad Stop/Clear pad START pad Melt, Soften, Warm pads
Oven Cavity Light Yes
Safety Standard
UL listed FCC Authorized DHHS Rules, CFR, Title 21, Chapter 1, Subchapter J
4 – 1
Page 8
R402JWT
3-Pronged Plug
Grounded Receptacle Box
Grounding Pin
3-Pronged Receptacle
1
6
5
2
10
11
9
7
8
3
4
R402JWT

CHAPTER 5. GENERAL INFORMATION

Service Manual

[1] GROUNDING INSTRUCTIONS

This oven is equipped with a three prong grounding plug. It must be plugged into a wall receptacle that is properly installed and grounded in accor­dance with the National Electrical Code and local codes and ordinances.
In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current.
WARNING:
Electrical Requirements
The electrical requirements are a 120 volt 60 Hz, AC only, 15 or 20 amp. fused electrical supply. It is recommended that a separate circuit serving only this appliance be provided. When installing this appliance, observe all applicable codes and ordinances. A short power-supply cord is provided to reduce risks of becoming entangled in or tripping over a longer cord. Where a two-pronged wall­receptacle is encountered, it is the personal responsibility and obligation of the customer to contact a qualified electrician and have it replaced with a properly grounded three-pronged wall receptacle or have a grounding adapter properly grounded and polarized. If the extension cord must be used, it should be a 3-wire, 15 amp. or higher rated cord. Do not drape over a countertop or table where it can be pulled on by children or tripped over accidentally.
CAUTION: DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE ROUND
Improper use of the grounding plug can result in a risk of electric shock.
GROUNDING PRONG FROM THIS PLUG.

[2] OVEN DIAGRAM

1. OVEN

1. One touch door open button.
Push to open door.
2. Door latches.
The oven will not operate unless the door is securely closed.
3. Removable turntable support
4. Removable turntable.
The turntable will rotate clockwise or counterclockwise.
5. Oven lamp.
It will light when oven is operating or door is opened.
6. Oven door with see-through win­dow
7. Ventilation openings. (Rear)
8. Auto-Touch control panel.
9. Time display: Digital display, 99 minutes, 99 seconds.
10.Waveguide cover:
11.Power supply cord.
5 – 1
Page 9

2. TOUCH CONTROL PANEL

R402JWT
NOTE: Some one-touch cooking features such as “MINUTE PLUS” are disabled after three minutes when the oven is not in use. These fea-
tures are automatically enabled when the door is opened and closed or the STOP/ CLEAR pad is pressed.
5 – 2
Page 10
R402JWT
R402JWT

CHAPTER 6. OPERATION

[1] DESCRIPTION OF OPERATING SEQUENCE

The following is a description of component functions during oven operation.
Service Manual

1. OFF CONDITION

Closing the door activates the door sensing switch and primary inter­lock switch. (In this condition, the monitor switch contacts are opened.)
When oven is plugged in, 120 volts A.C. is supplied to the control unit. (Figure O-1).
1) The display will show flashing “88:88”.
To set any program or set the clock, you must first touch the STOP/ CLEAR pad. The display will clear, and " : " will appear.

2. COOKING CONDITION

Program desired cooking time by touching the NUMBER pads. Pro­gram the power level by touching the POWERLEVEL pad and then a Number pad. When the START pad is touched, the following opera­tions occur:
1) The contacts of relays are closed and components connected to the relays are turned on as follows.
(For details, refer to Figure O-2)
RELAY CONNECTED COMPONENTS
RY-1 oven lamp/turntable motor/fan motor RY-2 power transformer
2) 120 volts A.C. is supplied to the primary winding of the power trans­former and is converted to about 3.3 volts A.C. output on the fila­ment winding, and approximately 2370 volts A.C. on the high voltage winding.
3) The filament winding voltage heats the magnetron filament and the H.V. winding voltage is sent to a voltage doubler circuit.
4) The microwave energy produced by the magnetron is channelled through the waveguide into the cavity feed-box, and then into the cavity where the food is placed to be cooked.
5) Upon completion of the cooking time, the power transformer, oven lamp, etc. are turned off, and the generation of microwave energy is stopped. The oven will revert to the OFF condition.
6) When the door is opened during a cook cycle, the monitor witch, door sensing switch, primary interlock switch, relay (RY1) and sec­ondary interlock relay are activated with the following results. The circuits to the turntable motor, the cooling fan motor, and the high voltage components are de-energized, the oven lamp remains on, and the digital read-out displays the time still remaining in the cook cycle when the door was opened.
7) The monitor switch electrically monitors the operation of the pri­mary interlock switch and secondary interlock relay and is mechan­ically associated with the door so that it will function in the following sequence.
a) When the door opens from the closed position, the secondary
interlock relay (RY2) and primary interlock switch open their contacts. And contacts of the relay (RY1) remains closed. Then the monitor switch contacts close.
b) When the door is closed from the open position, the monitor
switch contacts open first. Then the contacts of the primary interlock switch and door sensing switch close. And contacts of the relay (RY1) open.
If the primary interlock switch and secondary interlock relay (RY2) fail with the contacts closed when the door is opened, the closing of the monitor switch contacts will form a short circuit through the monitor fuse, primary interlock switch, relay (RY1) and secondary interlock relay (RY2), causing the monitor fuse to blow.

3. POWER LEVEL P-0 TO P-90 COOKING

When Variable Cooking Power is programmed, the 120 volts A.C. is supplied to the power transformer intermittently through the contacts of relay (RY-2) which is operated by the control unit within a 32 second time base. Microwave power operation is as follows:
VARI-MODE ON TIME OFF TIME P-HI (100% power) 32 sec. 0 sec. P-90 (approx. 90% power) 30 sec. 2 sec. P-80 (approx. 80% power) 26 sec. 6 sec. P-70 (approx. 70% power) 24 sec. 8 sec. P-60 (approx. 60% power) 22 sec. 10 sec. P-50 (approx. 50% power) 18 sec. 14 sec. P-40 (approx. 40% power) 16 sec. 16 sec. P-30 (approx. 30% power) 12 sec. 20 sec. P-20 (approx. 20% power) 8 sec. 24 sec. P-10 (approx. 10% power) 6 sec. 26 sec. P-0 (0% power) 0 sec. 32 sec.
NOTE: The ON/OFF time ratio does not correspond with the per-
centage of microwave power, because approx. 3 seconds are needed for heating of the magnetron filament.
6 – 1
Page 11

[2] OVEN SCHEMATIC

1. Off Condition

SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED
2. CLOCK APPEARS ON DISPLAY
R402JWT
120VAC
60Hz
N
OVE
THE
NOISE
FILTER
"TO LOAD"
C2
C3
"TO LOAD"
"TO SOURCE"
BLK
H
N
WHT
MONITOR
GRN
GND
C1: LINE CROSS CAPACITOR ------- 0.22uF/ AC250V C2, C3: LINE BYPASS CAPACITOR ------ 0.033uF/ AC250V
FUSE (20A)
C1
"TO SOURCE"
UT
CUT-O
L
A
RM
MAGNETRON
RAT
E
P
TEM FUSE
(RY1)
OVEN LAMP RELAY
RE
U
NOTE: " " indicates components with potentials above 250V
B2
TURN TAB LE MOTOR
B1
FAN
FM
MOTOR
(RY2)
SECONDARY
INTERLOCK
RELAY
CONTROL UNIT
OVEN
OL
LAMP
COM.
PRIMARY INTERLOCK SWITCH
TTM
N.O.
Figure O-1. Oven Schematic-Off Condition

2. Cooking Condition

SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. COOKING TIME PROGRAMMED.
3. VARIABLE COOKING CONTROL "P-HI".
4. START PAD TOUCHED.
DOOR SENSING SWITCH
MONITOR
SWITCH
COM.
N.C.
POWER TRANSFORMER
HIGH VOLTAGE CAPACITOR
0.94uF/ AC2200V
HIGH VOLTAGE RECTIFIER
MAGNETRON
-OUT
M TE F
USE
MPE
(RY1)
OVEN LAMP RELAY
RATURE
(RY2)
SECONDARY
INTERLOCK
RELAY
CONTROL UNIT
OVEN
OL
LAMP
COM.
PRIMARY INTERLOCK SWITCH
N.O.
TTM
TURN TAB LE MOTOR
B2
DOOR SENSING SWITCH
B1
FAN
FM
MOTOR
120VAC
60Hz
N
E
OV
RMALCUT
THE
NOISE FILTER
"TO LOAD"
C2
C3
"TO LOAD"
"TO SOURCE"
BLK
H
N
WHT
MONITOR
GRN
GND
C1: LINE CROSS CAPACITOR ------- 0.22uF/ AC250V C2, C3: LINE BYPASS CAPACITOR ------ 0.033uF/ AC250V
FUSE (20A)
C1
"TO SOURCE"
GNETRON
A
Figure O-2. Oven Schematic-Cooking Condition
6 – 2
MONITOR
SWITCH
COM.
N.C.
POWER TRANSFORMER
HIGH VOLTAGE CAPACITOR
0.94uF/ AC2200V
HIGH VOLTAGE RECTIFIER
MAGNETRON
Page 12
R402JWT

[3] DESCRIPTION AND FUNCTION OF COMPONENTS

1. DOOR OPEN MECHANISM

The door is opened by pushing the open button on the control panel, refer to the Figure D-1. When the open button is pushed, the open but­ton pushes up the switch lever, and then the switch lever pushes up the latch head. The latch heads are moved upward and released from latch hook. Now the door will open.
Latch Heads
Door
Switch Lever
Figure D-1. Door Open Mechanism.
Door Sensing Switch
Monitor Switch
Primary Interlock Switch

2. DOOR SENSING AND PRIMARY INTERLOCK SWITCHES

The primary interlock switch is mounted in the lower position of the latch hook and the door sensing switch in the secondary interlock sys­tem is mounted in the upper position of the latch hook. They are acti­vated by the latch heads on the door. When the door is opened, the switches interrupt the power to all high voltage components. A cook cycle cannot take place until the door is firmly closed there by activat­ing both interlock switches. The secondary interlock system consists of the door sensing switch and secondary interlock relay located on the control circuit board.

3. MONITOR SWITCH

The monitor switch is activated (the contacts opened) by the latch head on the door while the door is closed. The switch is intended to render the oven inoperative, by means of blowing the monitor fuse, when the contacts of the secondary interlock relay (RY2) and primary interlock switch fail to open when the door is opened.
Functions:
1) When the door is opened, the monitor switch contact close (to the ON condition) due to their being normally closed. At this time the secondary interlock relay (RY2) and primary interlock switch are in the OFF condition (contacts open) due to their being normally open contact switches.
2) As the door goes to a closed position, the monitor switch contacts are first opened and then the door sensing switch and the primary interlock switch contacts close. (On opening the door, each of these switches operate inversely.)
3) If the door is opened, and the secondary interlock relay (RY2) and primary interlock switch contacts fail to open, the monitor fuse blows simultaneously with closing of the monitor switch contacts.
CAUTION: BEFORE REPLACING A BLOWN MONITORFUSE TEST
THE DOOR SENSING SWITCH, SECONDARY INTER­LOCK RELAY (RY2), RE-LAY (RY1), PRIMARY INTER­LOCK SWITCH AND MONITOR SWITCH FOR PROPER OPERATION. (REFER TO CHAPTER “TEST PROCE­DURE”).
NOTE: MONITOR FUSE AND MONITOR SWITCH ARE REPLACED
AS AN ASSEMBLY.

4. TURNTABLE MOTOR

The turntable motor rotates the turntable located on the bottom of the oven cavity, so that the foods on the turntable cook evenly during cooking. The turntable may turn in either direction.

5. COOLING FAN MOTOR

The cooling fan motor drives a blade which draws external cool air. This cool air is directed through the air vanes surrounding the magne­tron and cools the magnetron. This air is channeled through the oven cavity to remove steam and vapors given off from the heating foods. It is then exhausted through the exhausting air vents at the oven cavity.

6. OVEN THERMAL CUT-OUT

The thermal cut-out, located on the top of the oven cavity, is designed to prevent damage to the oven by fire. If the food load is overcooked, by either error in cook time or defect in the control unit, the thermal cut­out will open. Under normal operation, the oven thermal cut-out remains closed. However, when abnormally high temperatures are reached within the oven cavity, the oven thermal cut-out will open at 293°F(145°C), causing the oven to shut down.

7. MAGNETRON TEMPERATURE FUSE

The magnetron temperature fuse located near the magnetron is designed to prevent damage to the magnetron if an over heated condi­tion develops in the tube due to cooling fan failure, obstructed air guide, dirty or blocked air intake, etc. Under normal operation, the magnetron temperature fuse remains closed. However, when abnor­mally high temperatures are reached within the magnetron, the mag­netron temperature fuse will open at 302°F(150°C) causing the oven to shut down.
NOTE: This is a fuse. It does not reset.

8. MONITOR FUSE

1) The monitor fuse blows when the contacts (COM-NO) of the pri­mary interlock relay (RY2) and secondary interlock switch remain closed with the oven door open and when the monitor switch closes.
2) If the wire harness or electrical components are short-circuited, this monitor fuse blows to prevent an electric shock or fire hazard.

9. NOISE FILER

The noise filter prevents the radio frequency interference that might flow back in the power circuit.
6 – 3
Page 13
R402JWT
R402JWT

CHAPTER 7. TROUBLESHOOTING GUIDE

Service Manual
Never touch any part in the circuit with your hand or an uninsulated tool while the power supply is connected.
When troubleshooting the microwave oven, it is helpful to follow the Sequence of Operation in performing the checks. Many of the possible causes of trouble will require that a specific test be performed. These tests are given a procedure letter which will be found in the "Test Procedure "section.
IMPORTANT:
If the oven becomes inoperative because of a blown monitor fuse, check the monitor switch, relay (RY1) secondary interlock relay (RY2), door sensing switch and primary interlock switch before replacing the monitor fuse. If the monitor fuse is replaced, the monitor switch must also be replaced. Use part FFS-BA033WRKZ or FFS-BA037WRKZ as an assembly.
IMPORTANT:
Whenever troubleshooting is performed with the power supply cord disconnected. It may in, some cases, be necessary to connect the power supply cord after the outer case has been removed, in this event,
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Disconnect the leads to the primary of the power transformer.
5) Ensure that the leads remain isolated from other components and oven chassis by using insulation tape.
6) After that procedure, reconnect the power supply cord.
When the testing is completed,
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Reconnect the leads to the primary of the power transformer.
5) Reinstall the outer case (cabinet).
6) Reconnect the power supply cord after the outer case is installed.
7) Run the oven and check all functions.

[1] TROUBLESHOOTING CHART

CONDITION
OFF
CONDITION
COOKING
CONDITION
TTEST PROCEDURE
POSSIBLE CASE
AND DEFECTIVE PARTS
PROBLEM
Home fuse or circuit breaker blows when power cord is plugged into wall receptacle
Monitor fuse blows when power cord is plug­ged into wall receptacle.
All letters and indicators do not appear in dis­play when power cord is first plugged into wall outlet.
Display does not operate properly when STOP/CLEAR pad is touched. (Buzzer should sound and " : " or time of day should appear in display.)
Oven lamp does not light when door is opened.
Oven lamp does not go out when door is closed.
Oven lamp lights but fan motor and turntable motor do not operate.
Oven does not go into cook cycle when START pad is touched
Oven seems to be operating but little or no heat is produced in oven load. (Food incom­pletely cooked or not cooked at all at end of cook cycle.)
Oven goes into a cook cycle but extremely uneven heating is produced in oven load (food).
Oven does not cook properly when program­med for Cooking Power P-50 mode. (Oper­ates properly on Cooking Power P-HI (HIGH) mode.)
Oven goes into DEFROST but food is not defrosted well.
RE CK A B C D E F F G H RE RE CK J CK CK CK K L NI
SHORT IN POWER CORD
SHORT OR OPENED WIRING
MAGNETRON
POWER TRANSFORMER
E
H.V. RECTIFIER ASSEMBLY
HIGH VOLTAGE CAPACITOR
OVEN THERMAL CUT-OUT
MAGNETRON TEMPERATURE FUSE
SECONDARY INTERLOCK SYSTEM
PRIMARY INTERLOCK SWITCH
MONITOR SWITCH
MONITOR FUSE
OVEN LAMP
COOLING FAN MOTOR
TURNTABLE MOTOR
TOUCH CONTROL PANEL
NOISE FILTER
WRONG OPERATION
LOW VOLTAGE
DIRTY OVEN CAVITY
M
KEY UNIT (MEMBRAINE SWITCH)
RELAY (RY1)
FOIL PATTERN ON PWB
DEFROST
7 – 1
Page 14
R402JWT
R402JWT

CHAPTER 8. TEST PROCEDURES

Service Manual

[1] Procedure A: MAGNETRON ASSEMBLY TEST

1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. To test for an open filament, isolate the magnetron from the high voltage circuit. A continuity check across the magnetron filament leads should indicate less than 1 ohm.
5. To test for a shorted magnetron, connect the ohmmeter leads between the magnetron filament leads and chassis ground. This test should indicate an infinite resistance. If there is little or no resistance the magnetron is grounded and must be replaced.
6. Reconnect all leads removed from components during testing.
7. Reinstall the outer case (cabinet).
8. Reconnect the power supply cord after the outer case is installed.
9. Run the oven and check all functions.

1. MICROWAVE OUTPUT POWER

The following test procedure should be carried out with the microwave oven in a fully assembled condition (outer case fitted).
HIGH VOLTAGES ARE PRESENT DURING THE COOK CYCLE, SO EXTREME CAUTION SHOULD BE OBSERVED.
Power output of the magnetron can be measured by performing a water temperature rise test. This test should only be used if above tests do not indi­cate a faulty magnetron and there is no defect in the following components or wiring: silicon rectifier, high voltage capacitor and power transformer. This test will require a 16 ounce (453cc) measuring cup and an accurate mercury thermometer or thermocouple type temperature tester. For accurate results, the following procedure must be followed carefully:
1. Fill the measuring cup with 16 oz. (453cc) of tap water and measure the temperature of the water with a thermometer or thermocouple tempera­ture tester. Stir the thermometer or thermocouple through the water until the temperature stabilizes. Record the temperature of the water.
2. Place the cup of water in the oven. Operate oven at POWER 10 (HIGH) selecting more than 60 seconds cook time. Allow the water to heat for 60 seconds, measuring with a stop watch, second hand of a watch or the digital read-out countdown.
3. Remove the cup from the oven and again measure the temperature, making sure to stir the thermometer or thermocouple through the water until the maximum temperature is recorded.
4. Subtract the cold water temperature from the hot water temperature. The normal result should be 34.8 to 64.6°F(19.3 to 35.9°C) rise in tempera- ture. If the water temperatures are accurately measured and tested for the required time period the test results will indicate if the magnetron tube has low power output (low rise in water temperature) which would extend cooking time or high power output (high rise in water temperature) which would reduce cooking time. Because cooking time can be adjusted to compensate for power output, the magnetron tube assembly should be replaced only if the water temperature rise test indicates a power output well beyond the normal limits. The test is only accurate if the power supply line voltage is 120 volts and the oven cavity is clean.

[2] Procedure B: POWER TRANSFORMER TEST

1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the primary input terminals and measure the resistance of the transformer with an ohmmeter. Check for continuity of the coils with an ohmmeter. On the R x 1 scale, the resistance of the primary coil should be less than 1 ohm and the resistance of the high voltage coil should be approximately 159 ohms (RTRN-A746WRZZ) or approximately 150 ohms (RTRN-A745WRZZ); the resistance of the filament coil should be less than 1 ohm.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
(HIGH VOLTAGES ARE PRESENT AT THE HIGH VOLTAGE TERMINAL, SO DO NOT ATTEMPT TO MEASURE THE FILAMENT AND HIGH VOLTAGE.)

[3] Procedure C: HIGH VOLTAGE RECTIFIER TEST

1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Isolate the rectifier from the circuit. Using the highest ohm scale of the meter, read the resistance across the terminals and observe, reverse the leads to the rectifier terminals and observe meter reading. If a short is indicated in both directions, or if an infinite resistance is read in both direc­tions, the rectifier is probably defective and should be replaced.
8 – 1
Page 15
R402JWT
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
NOTE: Be sure to use an ohmmeter that will supply a forward bias voltage of more than 6.3 volts.

[4] Procedure D: HIGH VOLTAGE CAPACITOR TEST

1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. If the capacitor is open, no high voltage will be available to the magnetron. Disconnect input leads and check for short or open between the termi­nals using an ohmmeter.
Checking with a high ohm scale, if the high voltage capacitor is normal, the meter will indicate continuity for a short time and should indicate an open circuit once the capacitor is charged. If the above is not the case, check the capacitor with an ohmmeter to see if it is shorted between either of the terminals and case. If it is shorted, replace the capacitor.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.

[5] Procedure E: TEMPERATURE FUSE OR THERMAL CUT-OUT TEST

1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Check a continuity across the temperature fuse or thermal cut-out terminals in the table below.
Table: Temperature Fuse and Thermal Cut-out Test
Parts Name
Temperature fuse 150°C This is not resetable type. Above 150°C (302°F) Closed circuit Thermal cut-out 145°C This is not resetable type. Above 145°C (293°F) Closed circuit
5. An open temperature fuse (Magnetron) indicates overheating of the magnetron. Check for restricted air flow to the magnetron, especially the cool­ing fan and air guide.
An open thermal cut-out (Oven) indicates overheating of the oven, exchange the thermal cut-out and check inside of oven cavity and for improper setting of cooking time or operation of control unit. Check for restricted air flow through the vent holes of the oven cavity, especially the cooling fan and air guide.
6. Reconnect all leads removed from components during testing.
7. Reinstall the outer case (Cabinet).
8. Reconnect the power supply cord after the outer case is installed.
9. Run the oven and check all functions.
CAUTION: IF THE TEMPERATURE FUSE OR THERMAL CUT-OUT INDICATES AN OPEN CIRCUIT AT ROOM TEMPERATURE, REPLACE IT.
Temperature of “ON” condition
(closed circuit).
Temperature of “OFF” condition
(open circuit).
Indication of ohmmeter (When room temperature is approx. 20°C.)

[6] Procedure F: PRIMARY INTERLOCK SWITCH TEST

1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal of the switch. The meter should indicate an open circuit with the door open and a closed circuit with the door closed. If improper operation is indicated, replace the primary interlock switch.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
8 – 2
Page 16
R402JWT

[7] Procedure F: SECONDARY INTERLOCK SYSTEM TEST

1. DOOR SENSING SWITCH

1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal of the switch. The meter should indicate an open circuit with the door open and a closed circuit with the door closed. If improper operation is indicated, replace the door sensing switch.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
NOTE: If the door sensing switch contacts fail in the open position and the door is closed, the cooling fan, turntable and oven light will be activated by
RY1.

2. SECONDARY INTERLOCK RELAY (RY2)

1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect two (2) wire leads from the male tab terminals of the Secondary Interlock Relay. Check the state of the relay contacts using a ohmme­ter. The relay contacts should be open. If the relay contacts are closed, replace the circuit board entirely or the relay itself.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.

[8] Procedure G: MONITOR SWITCH TEST

1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Before performing this test, make sure that the primary interlock switch and the secondary interlock relay are operating properly, according to the above Switch Test Procedure. Disconnect the wire lead from the monitor switch (COM) terminal. Check the monitor switch operation by using the ohmmeter as follows. When the door is open, the meter should indicate a closed circuit. When the monitor switch actuator is pushed by a screw driver through the lower latch hole on the front plate of the oven cavity with the door opened (in this condition the plunger of the monitor switch is pushed in), the meter should indicate an open circuit. If improper operation is indicated, the switch may be defective. After testing the monitor switch, reconnect the wire lead to the monitor switch (COM) terminal and check the continuity of the monitor circuit.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
Red
Screw Driver
Primary Interlock Switch
White/ White
Ohmmeter
Monitor Switch

[9] Procedure H: BLOWN MONITOR FUSE TEST

1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
8 – 3
Page 17
R402JWT
FUSE 20A
NOISE FILTER
NOISE SUPPRESSION COIL
LINE CROSS CAPACITOR
0.22μF / AC 250V
LINE BYPASS
CAPACITOR
0.0033μF / AC 250V
LINE BYPASS
CAPACITOR
0.0033μF / AC 250V
L
REDWHITE
N
3. Discharge high voltage capacitor.
4. If the monitor fuse is blown when the door is opened, check the primary interlock switch, secondary interlock relay (RY2), relay (RY1) and monitor switch according to the “TEST PROCEDURE” for those switches before replacing the blown monitor fuse.
CAUTION: BEFORE REPLACING A BLOWN MONITOR FUSE, TEST THE PRIMARY INTERLOCK SWITCH, SECONDARY INTERLOCK RELAY,
DOOR SENSING SWITCH AND MONITOR SWITCH FOR PROPER OPERATION.
If the monitor fuse is blown by improper switch operation, the monitor fuse and monitor switch must be replaced with “monitor fuse and monitor switch assembly” part number FFS-BA033WRKZ or FFS-BA037WRKZ, even if the monitor switch operates normally. The monitor fuse and moni­tor switch assembly is comprised of a 20 ampere fuse and switch.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.

[10] Procedure I: NOISE FILTER TEST

1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the lead wires from the terminal the noise filter. Using an ohmmeter, check between the terminals as described in the following table. If incorrect readings are obtained, replace the noise filter.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
MEASURING POINT INDICATION OF OHMMETER Between N and L Open circuit. Between terminal N and WHITE Short circuit. Between terminal L and RED Short circuit.

[11] Procedure J: TOUCH CONTROL PANEL ASSEMBLY TEST

The touch control panel consists of circuits including semiconductors such as LSI, ICs, etc. Therefore, unlike conventional microwave ovens, proper maintenance cannot be performed with only a voltmeter and ohmmeter.
In this service manual, the touch control panel assembly is divided into two units, Control Unit and Key Unit, and also the Control Unit is divided into two units, CPU Unit and Power Unit, and troubleshooting by unit replacement is described according to the symptoms indicated.
Before testing,
1) Disconnect the power supply cord and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Disconnect the leads to the primary of the power transformer.
5) Ensure that these leads remain isolated from other components and oven chassis by using insulation tape.

1. Key Unit

NOTE:
1) Re-install the outer case (cabinet).
2) Reconnect the power supply cord after the outer case is installed.
3) Run the oven and check all functions.
The following symptoms indicate a defective key unit.
a) When touching the pads, a certain pad produces no signal at all.
b) When touching a number pad, two figures or more are displayed.
c) When touching the pads, sometimes a pad produces no signal.

2. Control Unit.

The following symptoms indicate a defective control unit.
1) In connection with pads.
a) When touching the pads, a certain group of pads do not produce a signal.
8 – 4
Page 18
R402JWT
b) When touching the pads, no pads produce a signal.
2) In connection with indicators
a) At a certain digit, all or some segments do not light up.
b) At a certain digit, brightness is low.
c) Only one indicator does not light.
d) The corresponding segments of all digits do not light up; or they continue to light up.
e) Wrong figure appears.
f) A certain group of indicators do not light up.
g) The figure of all digits flicker.
3) Other possible problems caused by defective control unit.
a) Buzzer does not sound or continues to sound.
b) Clock does not operate properly.
c) Cooking is not possible.

3. If the Key unit or the Control unit is defective.

1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Replace the Control unit assembly.
5) Reconnect all leads removed from components during testing.
6) Re-install the outer case (cabinet).
7) Reconnect the power supply cord after the outer case is installed.
8) Run the oven and check all functions.

4. When testing is completed,

1) Disconnect the power supply cord and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Reconnect all leads removed from components during testing.
5) Re-install the outer case (cabinet).
6) Reconnect the power supply cord after the outer case is installed.
7) Run the oven and check all functions.

[12] Procedure K: KEY UNIT TEST

1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. If the display fails to clear when the STOP/CLEAR pad is depressed, first verify the flat ribbon cable is making good contact, verify that the door sensing switch (stop switch) operates properly; that is the contacts are closed when the door is closed and open when the door is open. If the door sensing switch (stop switch) is good, disconnect the flat ribbon cable that connects the key unit to the control unit and make sure the door sensing switch is closed (either close the door or short the door sensing switch connecter).
Use the Key unit matrix indicated on the control panel schematic and place a jumper wire between the pins that correspond to the STOP/CLEAR pad making momentary contact. If the control unit responds by clearing with a beep the key unit is faulty and must be replaced. If the control unit does not respond, it is faulty and must be replaced. If a specific pad does not respond, the above method may be used (after clearing the control unit) to determine if the control unit or key pad is at fault.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
G9
NIGHT
G10
LIGHT
G11
DEFROST
G12
SOFTEN MELT
G7 G6
COOK
G5 G4 G3G8
REHEAT
1
4
7
G2 G1
START
2
TIMER
5
CLOCK
STOP
8
CLEAR
POWER
0
LEVEL
WARM
9
3
6
MINUTE
PLUS
POPCORN
8 – 5
Page 19
R402JWT

[13] Procedure L: RELAY TEST

1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power transformer.
5. Ensure that these leads remain isolated from other components and oven chassis by using insulation tape.
6. After that procedure, re-connect the power supply cord.
7. Remove the outer case and check voltage between the cabinet side terminal of the relay RY1 and the lower side terminal of the relay RY2 on the control unit with an A.C. voltmeter.
The meter should indicate 120 volts, if not check oven circuit.
RY1 and RY2 Relay Test
These relays are operated by D.C. voltage
Check voltage at the relay coil with a D.C. voltmeter during the microwave cooking operation.
DC. voltage indicated ................. Defective relay.
DC. voltage not indicated ........... Check diode which is connected to the relay coil. If diode is good, control unit is defective.
RELAY SYMBOL OPERATIONAL VOLTAGE CONNECTED COMPONENTS
RY1 Approx. 12.0V D.C. Oven lamp / Turntable motor / Cooling fan motor RY2 Approx. 12.0V D.C. Power transformer
8. Disconnect the power supply cord and then remove outer case.
9. Open the door and block it open.
10.Discharge high voltage capacitor.
11.Reconnect all leads removed from components during testing.
12.Re-install the outer case (cabinet).
13.Reconnect the power supply cord after the outer case is installed.
14.Run the oven and check all functions.

[14] Procedure M: DEFROST TEST

WARNING: The oven should be fully assembled before following procedure.
1. Open the door.
2. Place one cup of water in the center of the turntable tray in the oven cavity.
3. Close the door, touch the “DEFROST“ pad once.
4. Press “2”, then press “5”.
5. Touch the “START “ pad.
6. The oven is in Defrost cooking condition.
7. The oven will operate as follows.
MENU 1ST STAGE 2ND STAGE 3RD STAGE
Steaks/Chops LEVEL TIME LEVEL TIME LEVEL TIME
0.5lb 60% 20sec. 40% 20sec. 30% 45sec.
8. If improper operation is indicated, the control unit is probably defective and should be checked.

[15] Procedure N: FOIL PATTERN ON THE PRINTED WIRING BOARD TEST

To protect the electronic circuits, this model is provided with a fine foil pattern added to the primary on the PWB, this foil pattern acts as a fuse.
1. Foil pattern check and repairs.
1) Disconnect the power supply cord and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Follow the troubleshooting guide given below for repair.
STEPS OCCURRENCE CAUSE OR CORRECTION
1 Only pattern at “a” is broken. *Insert jumper wire J1 and solder. 2 Pattern at “a” and “b” are broken. *Insert the coil RCILF2003YAZZ between “c” and “d”.
8 – 6
Page 20
R402JWT
a
b
d
c
5) Make a visual inspection of the varistor. Check for burned damage and examine the transformer with a tester for the presence of layer short-circuit (check the primary coil resistance which is approximately 563Ω±10%). If any abnormal condition is detected, replace the control unit.
6) Reconnect all leads removed from components during testing.
7) Re-install the outer case (cabinet).
8) Reconnect the power supply cord after the outer case is installed.
9) Run the oven and check all functions.
2. Follow the troubleshooting guide given below, if indicator does not light up after above check and repairs are finished.
1) Disconnect the power supply cord and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Disconnect the leads to the primary of the power transformer.
5) Ensure that these leads remain isolated from other components and oven chassis by using insulation tape.
6) After that procedure, re-connect the power supply cord.
7) Follow the troubleshooting guide given below for repair.
STEPS OCCURRENCE CAUSE OR CORRECTION
The rated AC voltage is not present between the cabinet side terminal of
1
the relay RY1 and the lower side terminal of the relay RY2. The rated AC voltage is present at primary side of low voltage trans-
2
former.
Check supply voltage and oven power cord.
Low voltage transformer or secondary circuit defective. Check and replace control unit.
8) Disconnect the power supply cord and then remove outer case.
9) Open the door and block it open.
10)Discharge high voltage capacitor.
11)Reconnect all leads removed from components during testing.
12)Re-install the outer case (cabinet).
13)Reconnect the power supply cord after the outer case is installed.
14)Run the oven and check all functions.
8 – 7
Page 21
R402JWT

CHAPTER 9. TOUCH CONTROL PANEL ASSEMBLY

Service Manual
R402JWT

[1] OUTLINE OF TOUCH CONTROL PANEL

The touch control section consists of the following units.
(1) Key Unit
(2) Control Unit (The Control Unit consists of Power Unit and LSI Unit).
The principal functions of these units and their related signals are explained below.

1. Key Unit

The key unit is composed of a matrix, signals generated in the LSI are sent to the key unit through P20-P27.
When a key pad is touched, a signal is completed through the key unit and passed back to the LSI through P70, P71, P41 and P45 to perform the function that was requested.

2. Control Unit

Control unit consists of LSI, reset circuit, indicator circuit, power source circuit, relay circuit, buzzer circuit, synchronizing signal circuit and back light circuit.
1) Reset Circuit
This circuit generates a signal which resets the LSI to the initial state when power is supplied.
2) Indicator Circuit
This circuit consists of 17 segments and 4 common electrodes using a Liquid Crystal Display.
3) Power Source Circuit
This circuit generates voltage necessary in the control unit from the AC line voltage.
In addition, the synchronizing signal is available in order to com­pose a basic standard time in the clock circuit.
Symbol Voltage Application
VSS -5V LSI(IC1)
4) Relay Circuit
A circuit to drive the magnetron, fan motor, turntable motor and light the oven lamp.
5) Buzzer Circuit
The buzzer is responsive to signals from the LSI to emit audible sounds (key touch sound and completion sound).
6) Synchronizing Signal Circuit
The power source synchronizing signal is available in order to com­pose a basic standard time in the clock circuit. It accompanies a very small error because it works on commercial frequency.
7) Door Sensing Switch
A switch to “tell” the LSI if the door is open or closed.
8) Back Light Circuit
A circuit to drive the back light (Light emitting diodes LD1- LD4).
9) Night Light Circuit
A circuit to drive the light emitting diode (LD10).

[2] DESCRIPTION OF LSI

The I/O signal of the LSI are detailed in the following table.
Pin No. Signal I/O Description
1-2 VL2-VL1 IN
3-6 AN7-AN4 IN
7 AN3 IN Terminal not used.
8AN2IN
9 AN1 IN Terminal not used.
10 AN0 IN Terminal not used.
11-13 P57-P55 OUT Terminal not used.
14 CNTR0 OUT
15 P53 OUT Terminal not used.
16 P52 OUT
Power source voltage input terminal.
Standard voltage for LCD.
Terminal to change cooking input according to the Model.
By using the A/D converter contained in the LSI, DC voltage in accordance with the Model in operation is applied to set up its cooking constant.
To input signal which communicates the door open/close information to LSI.
Door close “H” level signal (0V). Door open “L” level signal (-5V)
Signal to sound buzzer (2.0 kHz).
A: key touch sound. B: Completion sound.
Oven lamp, fan motor and turntable motor driving signal
To turn on and off shut off relay (RY1). The square wave­form voltage is delivered to the RY1 driving circuit and RY2 control circuit.
A
B
16.7 msec.
0.1 sec.
2.0 sec.
H : GND
L:-5V
H : GND
L:-5V
H:GND
17 P51 OUT Terminal not used.
9 – 1
During cooking
L:-5V
Page 22
R402JWT
Maximum output
70% of maximum output
H : GND
L : -5V
H : GND
L : -5V
ON
ON
OFF
OFF OFF
24 sec.
8 sec.
16.7 msec.
H:GND
L:-5V
Pin No. Signal I/O Description
Magnetron high-voltage circuit driving signal.
To turn on and off the cook relay (RY2). The signals holds “L” level during microwave cooking and “H” level while not cooking. In other cooking modes (variable
18 P50 OUT
19 P47 IN Connected to GND. 20 P46 OUT Night light circuit (light emitting diode) driving signal.
21 P45 IN
22-23 P44-P43 OUT Terminal not used.
24 INTP0 IN
cooking) the signal turns to “H” level and “L” level in repetition according to the power level.
Signal coming from touch key.
When either G12 line on key matrix is touched, a corresponding signal out of P20 - P27 will be input into P45. When no key is touched, the signal is held at “H” level.
Signal synchronized with commercial power source frequency.
This is the basic timing for time processing of LSI.
25 P41 IN
Signal similar to P45.
When either G11 line on key matrix is touched, a corresponding signal will be input into P41.
26 P40 IN Connected to GND through the pull-down resistor.
27 RESET IN
28 P71 IN
29 P70 IN
30 XIN IN
31 XOUT OUT
32 VSS IN
Auto clear terminal.
Signal is input to reset the LSI to the initial state when power is applied.
Signal similar to P45.
When either G10 line on key matrix is touched, a corresponding signal will be input into P71.
Signal similar to P45.
When either G9 line on key matrix is touched, a corresponding signal will be input into P70.
Internal clock oscillation frequency input setting.
The internal clock frequency is set by inserting the ceramic filter oscillation circuit with respect to XOUT terminal.
Internal clock oscillation frequency control output.
Output to control oscillation input of XIN.
Power source voltage: -5.0V.
The power source voltage to the drive LSI is input to VSS terminal.
Key strobe signal.
33 P27 OUT
Signal applied to touch-key section. A pulse signal is input to P70, P71, P41 and P45 terminal while one of G8 line keys on key matrix is touched.
Key strobe signal.
34 P26 OUT
Signal applied to touch-key section. A pulse signal is input to P70, P71, P41 and P45 terminal while one of G7 line keys on key matrix is touched.
Key strobe signal.
35 P25 OUT
Signal applied to touch-key section. A pulse signal is input to P70, P71, P41 and P45 terminal while one of G6 line keys on key matrix is touched.
Key strobe signal.
36 P24 OUT
Signal applied to touch-key section. A pulse signal is input to P70, P71, P41 and P45 terminal while one of G5 line keys on key matrix is touched.
Key strobe signal.
37 P23 OUT
Signal applied to touch-key section. A pulse signal is input to P70, P71, P41 and P45 terminal while one of G4 line keys on key matrix is touched.
Key strobe signal.
38 P22 OUT
Signal applied to touch-key section. A pulse signal is input to P70, P71, P41 and P45 terminal while one of G3 line keys on key matrix is touched.
Key strobe signal.
39 P21 OUT
Signal applied to touch-key section. A pulse signal is input to P70, P71, P41 and P45 terminal while one of G2 line keys on key matrix is touched.
Key strobe signal.
40 P20 OUT
Signal applied to touch-key section. A pulse signal is input to P70, P71, P41 and P45 terminal while one of G1 line keys on key matrix is touched.
41 P17 OUT Back light signal (light emitting diode) driving signal.
42-55 P16-P3 OUT Terminal not used.
9 – 2
Page 23
Pin No. Signal I/O Description
Segment data signal.
Connected to LCD. The relation between signals are as follows: LSI signal (Pin No.) LCD (segment) LSI signal (Pin No.) LCD (segment) SEG 0 (72) ----------------- SEG 0 SEG 9 (63) ----------------- SEG 9 SEG 1 (71) ----------------- SEG 1 SEG 10(62) ----------------- SEG 10
56-72 SEG16-SEG0 OUT
73 VCC IN Power source voltage: GND (0V).
74 VREF IN
75 AVSS IN
76 COM3 OUT
77 COM2 OUT
78 COM1 OUT
79 COM0 OUT
80 VL3 IN
SEG 2 (70) ----------------- SEG 2 SEG 11(61) ----------------- SEG 11 SEG 3 (69) ----------------- SEG 3 SEG 12 (60) ----------------- SEG 12 SEG 4 (68) ----------------- SEG 4 SEG 13 (59) ----------------- SEG 13 SEG 6 (66) ----------------- SEG 6 SEG 14 (58) ----------------- SEG 14 SEG 7 (65) ----------------- SEG 7 SEG 15 (57) ----------------- SEG 15 SEG 8 (64) ----------------- SEG 8 SEG 16 (56) ----------------- SEG 16
A/D converter power source voltage: GND (0V).
The power source voltage to drive the A/D converter. Connected to GND.
A/D converter power source voltage: -5.0V.
The power source voltage to drive the A/D converter.
Common data signal.
Connected to LCD signal COM3.
Common data signal.
Connected to LCD signal COM0.
Common data signal.
Connected to LCD signal COM1.
Common data signal.
Connected to LCD signal COM2.
Power source voltage input terminal.
Standard voltage for LCD. Connected to GND.
R402JWT
9 – 3
Page 24
R402JWT

[3] SERVICING FOR TOUCH CONTROL PANEL

1. Precautions for Handling Electronic Components

This unit uses CMOS LSI in the integral part of the circuits. When han­dling these parts, the following precautions should be strictly followed. CMOS LSI have extremely high impedance at its input and output ter­minals. For this reason, it is easily influenced by the surrounding high voltage power source, static electricity charge in clothes, etc., and sometimes it is not fully protected by the built-in protection circuit.
In order to protect CMOS LSI.
1) When storing and transporting, thoroughly wrap them in aluminium foil. Also wrap PW boards containing them in aluminium foil.
2) When soldering, ground the technician as shown in the figure and use grounded soldering iron and work table.
approx. 1M ohm

2. Servicing of Touch Control Panel

We describe the procedures to permit servicing of the touch control panel of the microwave oven and the precautions you must take when doing so. To perform the servicing, power to the touch control panel is available either from the power line of the oven itself or from an exter­nal power source.
1. Servicing the touch control panel with power supply of the oven:
CAUTION: THE HIGH VOLTAGE TRANSFORMER OF THE MICRO-
WAVE OVEN IS STILL LIVE DURING SERVICING AND PRESENTS A HAZARD.
Therefore, before checking the performance of the touch control panel,
1) Disconnect the power supply cord and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Disconnect the leads to the primary of the power transformer.
5) Ensure that these leads remain isolated from other components
and oven chassis by using insulation tape.
6) After that procedure, re-connect the power supply cord.
After checking the performance of the touch control panel,
1) Disconnect the power supply cord.
2) Open the door and block it open.
3) Re-connect the leads to the primary of the power transformer.
4) Re-install the outer case (cabinet).
5) Re-connect the power supply cord after the outer case is
installed.
6) Run the oven and check all functions.
a) On some models, the power supply cord between the touch
control panel and the oven itself is so short that the two can't be separated. For those models, check and repair all the controls (sensor-related ones included) of the touch control panel while keeping it connected to the oven.
b) On some models, the power supply cord between the touch
control panel and the oven proper is so long enough that they may be separated from each other. For those models, therefore, it is possible to check and repair the controls of the touch control panel while keeping it apart from the oven proper; in this case you must short both ends of the door sensing switch (on PWB) of the touch control panel with a jumper, which brings about an operational state that is equiv­alent to the oven door being closed. As for the sensor­related controls of the touch control panel, checking them is possible if the dummy resistor(s) with resistance equal to that of the controls are used.
2. Servicing the touch control panel with power supply from an exter­nal power source:
Disconnect the touch control panel completely from the oven proper, and short both ends of the door sensing switch (on PWB) of the touch control panel, which brings about an operational state that is equivalent to the oven door being closed. Connect an exter­nal power source to the power input terminal of the touch control panel, then it is possible to check and repair the controls of the touch control panel; it is also possible to check the sensor-related controls of the touch control panel by using the dummy resistor(s).

3. Servicing Tools

Tools required to service the touch control panel assembly.
1) Soldering iron: 60W
(It is recommended to use a soldering iron with a grounding termi­nal.)
2) Oscilloscope: Single beam, frequency range: DC - 10MHz type or more advanced model.
3) Others: Hand tools

4. Other Precautions

1) Before turning on the power source of the control unit, remove the aluminium foil applied for preventing static electricity.
2) Connect the connector of the key unit to the control unit being sure that the lead wires are not twisted.
3) After aluminium foil is removed, be careful that abnormal voltage due to static electricity etc. is not applied to the input or output ter­minals.
4) Attach connectors, electrolytic capacitors, etc. to PWB, making sure that all connections are tight.
5) Be sure to use specified components where high precision is required.
9 – 4
Page 25
R402JWT
R402JWT

CHAPTER 10. PRECAUTIONS FOR USING LEAD-FREE SOLDER

Service Manual

[1] Employing lead-free solder

The “Main PWB” of this model employs lead-free solder. This is indicated by the “LF” symbol printed on the PWB and in the service manual. The suffix letter indicates the alloy type of the solder.
Example:
Indicates lead-free solder of tin, silver and copper

[2] Using lead-free wire solder

When repairing a PWB with the “LF” symbol, only lead-free solder should be used. (Using normal tin/lead alloy solder may result in cold soldered joints and damage to printed patterns.)
As the melting point of lead-free solder is approximately 40°C higher than tin/lead alloy solder, it is recommend that a dedicated bit is used, and that the iron temperature is adjusted accordingly.

[3] Soldering

As the melting point of lead-free solder (Sn-Ag-Cu) is higher and has poorer wettability, (flow), to prevent damage to the land of the PWB, extreme care should be taken not to leave the bit in contact with the PWB for an extended period of time. Remove the bit as soon as a good flow is achieved. The high content of tin in lead free solder will cause premature corrosion of the bit. To reduce wear on the bit, reduce the temperature or turn off the iron when it is not required.
Leaving different types of solder on the bit will cause contamination of the different alloys, which will alter their characteristics, making good soldering more difficult. It will be necessary to clean and replace bits more often when using lead-free solder. To reduce bit wear, care should be taken to clean the bit thoroughly after each use.
10 – 1
Page 26
R402JWT
R402JWT
CHAPTER 11. COMPONENT REPLACEMENT AND ADJUSTMENT PROCE-
Service Manual
DURE

[1] WARNINGS

WARNING AGAINST HIGH VOLTAGE:
Microwave ovens contain circuitry capable of producing very high voltage and current, contact with following parts may result in severe, possibly fatal, electric shock. (Example) High Voltage Capacitor, Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..
WARNING:
1. Disconnect the power supply cord.
2. Make sure that a definite "click" can be heard when the microwave oven door is unlatched. (Hold the door in a closed position with one hand, then push the door open button with the other, this causes the latch leads to rise, it is then possible to hear a "click" as the door switches operate.)
3. Visually check the door and cavity face plate for damage (dents, cracks, signs of arcing etc.).
Carry out any remedial work that is necessary before operat­ing the oven. Do not operate the oven if any of the following conditions exist;
1. Door does not close firmly.
Avoid possible exposure to microwave energy. Please follow the instructions below before operating the oven.
WARNING FOR WIRING
To prevent an electric shock, take the following precau­tions.
1. Before wiring,
1) Disconnect the power supply cord.
2) Open the door block it open.
3) Wait for 60 seconds, then discharge the high voltage capacitor.
2. Do not let the wire leads touch to the following parts;
1) High voltage parts: Magnetron, High voltage transformer, High voltage capacitor and High voltage rectifier assembly.
2) Hot parts: Oven lamp, Magnetron, Power transformer and Oven cavity.
2. Door hinge, support or latch hook is damaged.
3. The door gasket or seal is damaged.
4. The door is bent or warped.
5. There are defective parts in the door interlock system.
6. There are defective parts in the microwave generating and transmission assembly.
7. There is visible damage to the oven.
Do not operate the oven:
1. Without the RF gasket (Magnetron).
2. If the wave guide or oven cavity are not intact.
3. If the door is not closed.
4. If the outer case (cabinet) is not fitted.
3) Sharp edge: Bottom plate, Oven cavity, Waveguide flange, Chassis support and other metallic plate.
4) Movable parts (to prevent a fault) Fan blade, Fan motor, Switch, Switch lever, Open button.
3. Do not catch the wire leads in the outer case cabinet.
4. Insert the positive lock connector until its pin is locked and make sure that the wire leads do not come off even if the wire leads are pulled.
5. To prevent an error function, connect the wire leads correctly, referring to the Pictorial Diagram.
Please refer to “OVEN PARTS, CABINET PARTS, CONTROL PANEL PARTS, DOOR PARTS”, when carrying out any of the following removal proce­dures:
11 – 1
Page 27

[2] OUTER CASE REMOVAL

To remove the outer case, procedure as follows.
1. Disconnect the power supply cord.
2. Open the oven door and block it open.
3. Remove the two (2) screws from the lower portion of the rear cabi­net using a T20H Torx type or GTXH20-100 screw driver.
4. Remove the remaining two (2) screws from rear.
5. Slide the entire outer case back out about 1 inch (3 cm) to free it from retaining clips on the cavity face plate.
6. Lift entire outer case from the unit.
CAUTION: DISCONNECT OVEN FROM POWER SUPPLY BEFORE
REMOVING OUTER CASE.
DISCHARGE THE HIGH VOLTAGE CAPACITOR BEFORE TOUCHING ANY OVEN COMPONENTS OR WIRING.

[3] POWER TRANSFORMER REMOVAL

R402JWT
NOTE: When replacing the outer case, the 2 special Torx screws
must be reinstalled in the same locations.
Special screw
Screw Driver (Type: TORX T20 H or GTXH20-100)

1. REMOVAL

1. Disconnect the power supply cord and remove outer case.
2. Open the oven door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect wire leads (primary) from power transformer and the fil­ament leads from the magnetron and capacitor terminals.
5. Disconnect high voltage lead of the power transformer from the high voltage capacitor.
6. Remove two (2) screws holding transformer to bottom plate.
7. Remove transformer from bottom plate.

2. REINSTALLATION

1. Rest transformer on the bottom plate with its primary terminals toward the oven face plate.
2. Secure transformer with two (2) screws to bottom plate.
3. Reconnect the wire leads (primary) to power transformer and fila­ment leads of transformer to magnetron and high voltage capacitor. Reconnect the high voltage lead of the power transformer to the high voltage capacitor. Refer to “PICTORIAL DIAGRAM”.
4. Reinstall outer case and check that oven is operating properly.

[4] HIGH VOLTAGE RECTIFIER AND HIGH VOLTAGE CAPACITOR REMOVAL

To remove the components, proceed as follows.
1. Disconnect the power supply cord and remove outer case.
2. Open the oven door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the high voltage wire of the power transformer from the high voltage capacitor.
5. Disconnect the high voltage wire of high voltage rectifier assembly from the magnetron.
6. Disconnect the filament lead (short one) of the power transformer from the high voltage capacitor.
7. Remove the one (1) screw holding capacitor holder with the high voltage rectifier to the base plate.
8. Disconnect rectifier terminal from capacitor. High voltage rectifier assembly is now free.
9. Remove capacitor holder. Capacitor is now free.
CAUTION: WHEN REPLACING HIGH VOLTAGE RECTIFIER AND
HIGH VOLTAGE CAPACITOR, GROUND SIDE TERMI­NAL OF THE HIGH VOLTAGE RECTIFIER MUST BE SECURED FIRMLY WITH A GROUNDING SCREW.

[5] MAGNETRON REMOVAL

1. REMOVAL

1. Disconnect the power supply cord and then remove outer case.
2. Open the oven door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect all wire leads from magnetron.
5. Remove the two (2) screws holding the chassis support to the mag­netron and the oven cavity front flange.
6. Slide the magnetron duct slightly so that the two (2)screws at left hand side of the magnetron appear.
7. Carefully remove the four (4) screws holding magnetron to waveguide flange.
8. Remove magnetron with care so that magnetron antenna is not hit by any metal object around the antenna.
9. Now, the magnetron is free.

2. REINSTALLATION

1. Re-install the magnetron to waveguide flange with car to prevent damage to the magnetron antenna.
2. Secure the magnetron with the four (4) screws.
11 – 2
Page 28
R402JWT
Terminal
Push
Pull down
1
2
Lever
Positive lock¨ connector
3. Hold the chassis support to the oven cavity front plate and the mag­netron with the two (2) screws.
4. Reconnect the wire leads to the magnetron. Refer to “PICTORIAL DIAGRAM”.
5. Reinstall outer case and check that the oven is operating properly.
CAUTION: WHEN REPLACING MAGNETRON, BE SURE THE R.F.
GASKET IS IN PLACE AND MOUNTING SCREWS ARE TIGHTENED SECURELY.

[6] OVEN LAMP REMOVAL

1. Disconnect the power supply cord and then remove outer case.
2. Open the oven door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the wire leads from the oven lamp.
5. Remove the one (1) screw holding the oven lamp to the magnetron duct.
6. Remove the oven lamp from the magnetron duct.
7. Now, the oven lamp is free.
Terminal
Figure C-1. Oven lamp

[7] POSITIVE LOCK CONNECTOR (NO-CASE TYPE) REMOVAL

1. Disconnect the power supply cord, and remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Push the lever of positive lock® connector.
5. Pull down on the positive lock® connector.
CAUTION: WHEN CONNECTING THE POSITIVE LOCK® CONNEC-
TORS TO THE TERMINALS, CONNECT THE POSITIVE LOCK® SO THAT THE LEVER FACES YOU.
Oven lamp
Figure C-2. Positive lock® connector

[8] CONTROL PANEL ASSEMBLY REMOVAL

1. Disconnect the power supply cord and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the wire leads from panel components.
5. Straighten the nail holding the control panel assembly to the oven cavity front plate.
6. Slide the control panel assembly upward and remove it.
7. Now, individual components can be removed.

[9] GRAPHIC SHEET AND MEMBRANE SWITCH REPLACEMENT

1. REMOVAL

1. Disconnect the power supply cord and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the control panel assembly, referring to chapter of CON­TROL PANEL ASSEMBLY REMOVAL.
5. Disconnect the ribbon cable of the membrane switch from the con­trol unit.
6. Remove the back light PWB from the control panel frame.
7. Remove the four (4) screws holding the control unit to the control panel frame. And remove the control unit.
8. Remove the display window from the control panel frame.
9. Tear away the graphic sheet from the control panel frame.
10.Tear away the membrane switch from the control panel frame.

2. REINSTALLATION

1. Remove remaining adhesive on the control panel frame surfaces with a soft cloth soaked in alcohol.
2. Tear the backing paper from the new membrane switch.
3. Insert the ribbon cable of the membrane switch into the slit of the control panel frame.
4. Adjust the upper edge and right edge of the membrane switch to the small depression on the surface of the control panel frame.
5. Attach the membrane switch to the control panel frame by rubbing with a soft cloth not to scratch.
6. Tear the backing paper from the new graphic sheet.
7. Adjust the upper edge and right edge of the graphic sheet to the large depression on the surface of the control panel frame.
8. Attach the graphic sheet to the control panel frame by rubbing with a soft cloth not to scratch.
9. Insert the ribbon cable into the slit of the control unit.
10.Reinstall the control unit to the control panel frame and hold with the four (4) screws.
11.Insert and connect the edge of the membrane switch’s ribbon cable into the connector CN-G.
12.Insert the back light PWB into the square hole.
13.Reinstall the display window to the control panel frame.
11 – 3
Page 29
R402JWT
Left tab
Square hole of control panel frame
Wire lead
Back light PWB (LD10)
Back light PWB installation
CAUTION: When the back light PWB is installed into the square hole
of the control panel frame, the wire leads should be routed through the cut off portion, not to be pinched.
Cut off portion
Right tab

[10] TURNTABLE MOTOR REMOVAL

1. Disconnect the power supply cord.
2. Remove turntable and turntable support from oven cavity.
3. Lay the oven on it's backside. Remove the turntable motor cover by snipping off the material in four corners.
4. Where the corners have been snipped off bend corner areas flat. No sharp edges must be evident after removal of the turntable motor cover.
Control panel frame
Small
Display window
Graphic sheet
Graphic Sheet and Membrane Switch Replacement
5. Disconnect wire leads from turntable motor.
(See “Positive lock® connector removal”)
6. Remove one (1) screw holding turntable motor to oven cavity.
7. Now, the turntable motor is free.
8. After replacement use the one (1) screw XOTS740P10000 to fit the turntable motor cover.
depression
Ribbon cable
Membrame switch
Large depression
Slit

[11] COOLING FAN MOTOR REMOVAL

1. REMOVAL

1. Disconnect the power supply cord and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the wire leads from the fan motor.
5. Remove the two (2) screws holding the fan motor to the oven cavity back plate.
6. Remove the fan blade from the fan motor shaft according to the fol­lowing procedure.
7. Hold the edge of the rotor of the fan motor by using a pair of groove joint pliers.
CAUTION: Make sure that no metal pieces enter the gap between
the rotor and the stator of the fan motor because the rotor is easily shaven by pliers and metal pieces may be produced.
Do not touch the pliers to the coil of the fan motor because the coil may be cut or injured.
Do not disfigure the bracket by touching with the pli­ers.
8. Remove the fan blade assembly from the shaft of the fan motor by pulling and rotating the fan blade with your hand.
9. Now, the fan blade will be free.
CAUTION: Do not reuse the removed fan blade because the hole
(for shaft) may be larger than normal.

2. REINSTALLATION

1. Install the fan blade to the fan motor shaft according to the following procedure.
2. Hold the center of the bracket which supports the shaft of the fan motor on the flat table.
3. Apply the screw lock tight into the hole (for shaft) of the fan blade.
4. Install the fan blade to the shaft of fan motor by pushing the fan blade with a small, light weight, ball peen hammer or rubber mallet.
CAUTION: Do not hit the fan blade strongly when installed
because the bracket may be disfigured.
Make sure that the fan blade rotates smooth after installation.
Make sure that the axis of the shaft is not slanted.
5. Install the fan motor assembly to the oven cavity back plate with two (2) screws.
6. Connect the wire leads to the magnetron and fan motor, referring to the pictorial diagram.
11 – 4
Page 30
R402JWT
Coil
Stator
Gap
Bracket
Rotor
Groove joint pliers
Rear View
Axis
Shaft
Stator
Rotor
Side View
These are the positions that should be pinched with pliers.
Table
Shaft
Center of bracket

[12] DOOR SENSING SWITCH/PRIMARY INTERLOCK SWITCH AND MONITOR SWITCH REMOVAL

1. REMOVAL

1. Disconnect the power supply cord and remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect wire leads from the switches.
5. Remove two (2) screws holding latch hook to oven flange.
6. Remove latch hook assembly from oven flange.
7. Push outward on the two (2) retaining tabs holding switch in place.
8. Switch is now free.
At this time switch lever will be free, do not lose it.

2. REINSTALLATION

1. Re-install each switch in its place. The primary interlock/ monitor switches are in the lower position and the door sensing switch is in the upper position.
2. Reconnect wire leads to each switch. Refer to pictorial diagram.
3. Secure latch hook (with two (2) mounting screws) to oven flange.
4. Make sure that the monitor switch is operating properly and check continuity of the monitor circuit. Refer to chapter “Test Procedure” and Adjustment procedure.

[13] DOOR SENSING SWITCH/PRIMARY INTERLOCK SWITCH AND MONITOR SWITCH ADJUSTMENT

1. Adjustment

1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
If the door sensing switch, primary interlock switch and monitor switch do not operate properly due to a misadjustment, the following adjust­ment should be made.
4. Loosen the two (2) screws holding latch hook to the oven cavity front flange.
5. With door closed, adjust latch hook by moving it back and forth, and up and down. In and out play of the door allowed by the upper and lower position of the latch hook should be less than 0.5mm. The vertical position of the latch hook should be adjusted so that the door sensing switch and primary interlock switch are activated with the door closed. The horizontal position of the latch hook should be adjusted so that the plunger of the monitor switch is pressed with the door closed.
6. Secure the screws with washers firmly.
7. Check the operation of all switches. If each switch has not activated with the door closed, loosen screw and adjust the latch hook posi­tion.
Then check lower portion of the latch hook, pushing and pulling lower portion of the door toward the oven face. Both results (play in the door) should be less than 0.5mm.
2. The door sensing switch and primary interlock switch interrupt the circuit before the door can be opened.
3. Monitor switch contacts close when door is opened.
4. Re-install outer case and check for microwave leakage around door with an approved microwave survey meter. (Refer to Micro­wave Measurement Procedure.)
Latch Heads
Door
Switch Lever
Door Sensing Switch
Monitor Switch

2. After adjustment, check the following.

1. In and out play of door remains less than 0.5mm when in the latched position. First check upper position of latch hook, pushing and pulling upper portion of door toward the oven face.

[14] DOOR REPLACEMENT

1. REMOVAL

1. Disconnect oven from power supply.
Primary Interlock Switch
Figure C-3. Latch Switch Adjustments
2. Push the open button and open the door slightly.
11 – 5
Page 31
3. Insert a putty knife (thickness of about 0.5mm) into the gap
Pin
Pin
Upper oven hinge
Lower oven hinge
Lower oven hinge
Door stopper
Choke cover
Door assembly
between the door stopper and the choke cover to free engaging parts as shown in Figure C-4.
4. Try the principles of the lever and lift up the door stopper.
5. Now, the door stopper is free from the door assembly.
6. Release two (2) pins of door panel from two (2) holes of upper and lower oven hinges by lifting up.
7. Now, door panel is free from oven cavity.
8. Insert a putty knife (thickness of about 0.5mm) into the gap between the choke cover and door frame as shown in Figure C-4 to free engaging parts.
9. Pry the choke cover by inserting a putty knife as shown Figure C-4.
10.Release choke cover from door panel.
11.Now choke cover is free.
NOTE: When carrying out any repair to the door, do not bend or
warp the slit choke (tabs on the door panel assembly) to prevent microwave leakage.
Door stopper
1
2
13
3
12
10
11
9
6
7
8
4
5
Door Frame
Putty Knife
R402JWT
2) An approved microwave survey meter should be used to
assure compliance with proper microwave radiation emission limitation standards.

3. After any service, make sure of the following:

1. Door latch heads smoothly catch latch hook through latch holes and that latch head goes through center of latch hole.
2. Deviation of door alignment from horizontal line of cavity face plate is to be less than 1.0mm.
3. Door is positioned with its face pressed toward cavity face plate.
4. Check for microwave leakage around door with an approved micro­wave survey meter. (Refer to Microwave Measurement Procedure.)
NOTE: The door on a microwave oven is designed to act as an
electronic seal preventing the leakage of microwave energy from oven cavity during cook cycle. This function does not require that door be air-tight, moisture (conden­sation)-tight or light-tight. Therefore, occasional appear­ance of moisture, light or sensing of gentle warm air movement around oven door is not abnormal and do not of themselves indicate a leakage of microwave energy from oven cavity.
Choke Cover
Figure C-4. Door Disassembly
12.Slide latch head upward and remove it from door frame with releas­ing latch spring from door frame and latch head.
13.Now, latch head and latch spring are free.
14.Release door panel from nine (9) tabs of door frame by sliding door panel downward.
15.Now, door panel with sealer film is free.
16.Tear sealer film from door panel.
17.Now, door panel is free.
18.Remove door screen from door frame.
19.Now, door screen is free.

2. REINSTALLATION

1. Reinstall door screen to door frame.
2. Put sealer film on door panel. Refer to “Sealer Film” about how to handle new one.
3. Reinstall door panel to door frame by fitting nine (9) tabs of door frame to nine (9) holes of door panel.
4. Reinstall the latch spring to the latch head. Reinstall the latch spring to the door frame. Reinstall latch head to door frame.
5. Reinstall choke cover to door panel by pushing
6. Catch two (2) pins of door panel on two (2) hole of upper and lower oven hinges as shown Figure C-5.
7. Re-install the door stopper to the door assembly.
NOTE: After any service to the door;
1) Make sure that door sensing switch and primary interlock
switch are operating properly. (Refer to chapter “Test Proce­dures”.).
Figure C-5. Door Replacement

4. SEALER FILM

1. Put the adhesive tape on the backing film of the sealer film as shown in Fig. C-6.
2. Tear the backing film by pulling the adhesive tape.
3. Put the pasted side of the sealer film on the door panel.
Sealer film
Backing film
Adhesive tape
Figure C-6. Sealer film
11 – 6
Page 32
R402JWT
R402JWT

CHAPTER 12. CIRCUIT DIAGRAMS

[1] Pictorial Diagram (Figure S-1)

RED
RED
L
N
WHT
NOTE:
N
H
supply cord fixing screw.
The grounding conductor of
the power supply cord has
been grounded by power
The screw must always be
kept tight.
POWER SUPPLY
CORD 120V 60Hz
RED
RED
NOTE:
WHT
The neutral (WHT) wire must be connected to the
terminal with "N" mark on the power supply cord.
WHT
Service Manual
ORG
WHT
WHT
ORG
HIGH
VOLTAGE
CAPACITOR
H.V. RECTIFIER
POWER
TRANSFORMER
GRY
N.O.
DOOR
SENSING
THERMAL CUT-OUT
GRN
COM.
SWITCH
RED
(OVEN)
RED
GRN
GRN
ORG
RED
ORG
MAGNETRON TEMP FUSE
OVEN LAMP
ORG
GRY
FAN MOTOR
RED
N.C.
WHT
WHT
COM.
HIGH VOLTAGE COMPONENTS
SWITCH MONITOR
MAGNETRON
BRN
WHT
WHT
WHT
NO
WHT
TURNTABLE
MOTOR
GRY
GRY
WHT
RED
Figure S-1. Pictorial Diagram
to Chassis support
CONTROL UNIT
GRN 2
GRY 1
CN-B
CN-G
112
CN-B
SP1
2
1
SECOND
INTERLOCK
12 – 1
RELAY
RY2
RED
COM.
PRIMARY
INTERLOCK
SWITCH
BRN
ORG
RY1
GRY
WHT
T1
RED
Page 33

[2] Control Panel Circuit (Figure S-2)

R402JWT
LCD (RLCDSA155DR ZZ)
9
PLUS
MINUTE
3
POPCORN
6
(F)
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
64
SEG9
SEG8
SEG10
65
P3P4P5P6P7P8P9
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
P10
P11
P12
41
P13
P14
P15
P16
P17
40
WARM
CF1
STOP
TIMER
START
CSTLS4M00G56P18-A0
IC1
80
VL1
VL2
AN7
AN6
1
10K
R15
10K
R14
10K
R13
AN7
GND
AN5 AN6
AN4
P57
P56
P55
P53
P52
P51
P50
P47
P46
AN5
AN4
AN3
AN2
AN1
AN0
CNTR0
P45
25
P44
P43
INT0
24
(G)
15K
R110
G8 G7 G6 G5 G4 G3 G2 G1
C60C63:330pF/50Vx4
CLOCK
5
2
1
REHEAT
LIGHT
NIGHT
LEVEL
CLEAR
POWER
8
0
7
4
COOK
MELT
SOFTEN
DEFROST
KEY UNIT
CN-G
5597-12CPB7F
D1~D4
R74R78:270Kx5
Q10
2SA1037AK
50V
C20
DTA143EKA
Q30
Q11
DTA143EKA
(F)
BL
-5V
INT
GND
0.1uF
Q20
DTA143EKA
BZ
NL
COM
DTA143EKA
Q21
M
R41
15K
CPU UNIT
DOOR
R68
P70
15K
R69
P71
15K
R70
P41
15K
R71
P45
15K
R72
15K
(G)
5%
R3R2
510
1/2W
4.7K 1/4W
R5
WIER
JUMPER
D5 D6
1SS270A x2
V
C1
50
0.1uF
1N4002x4
T1
PA151DR
d
ab
LD1LD2LD 3LD4
KTA1267Y
Q2
SP1
LTST-C190KGKT x 4
R4
27 1/4W
510
1/2W
c
R7 R8
WH-1
RY1
510
1/2W
DU12D1-1P(M)-R
WH-1
DTD143ES
Q3
C5
10u/35V
RY2
DU12D1-1P(M)-R
DTA123JS
Q4
1SS270A
D30
B-1
POWER UNIT
1SS270A
D31
B-2
: IF NOT SPECIFIED 1/10W
NOTE:
Figure S-2. Control Panel Circuit
AC(N)
OVEN LAMP,
TURNTABLE
MOTOR,
FAN MOTOR
12 – 2
AC(H)
MICRO
DOOR
SENSING
SWITCH
Page 34
R402JWT

[3] Printed Wiring Board (Figure S-3)

Figure S-3. Printed Wiring Board
12 – 3
Page 35
PARTS LIST
HOW TO ORDER REPLACEMENT PARTS
To have your order filled promptly and correctly, please furnish the following information.
1. MODEL NUMBER
2. REF. NO.
3. PART NO.
4. DESCRIPTION
Parts marked "*" may cause undue microwave exposure. Parts marked " " are used in voltage more than 250V.
CONTENTS
MODELS
R402JWT
MICROWAVE OVEN
R-402JK-T R-402JW-T
[1] OVEN PARTS
[2] DOOR & CONTROL
DOOR PROTECTION SHEET
SPADPA204WRE0
6- 7 OPERATION MANUAL
6-2 TURNTABLE TRAY
FOAM SHEET (For R-402JK-T)
SPAKHA013WREZ
INTO THE OVEN CAVITY
6-1 TURNTABLE SUPPORT
PANEL PARTS
INDEX
TOP PAD ASSEMBLY
FPADBA626WRKZ
CABINET COVER
SPAKHA010WRE0
PLASTIC BAG
SSAKHA032WRE0
BOTTOM PAD ASSEMBLY
FPADBA627WRKZ
TRAY PACK
SPADFA389WRE0
Not replaceable items.
SHARP CORPORATION
PACKING CASE FPAK-A564WRKZ [R-402JK-T] FPAK-A565WRKZ [R-402JW-T]
This document has been published to be used for after sales service only. The contents are subject to change without notice.
Page 36
R402JWT
[1] OVEN PARTS
1-6
4-15
7-10
7-2
7-10
2-1
4-13
7-2
6-3
6-4
4-11
1-10
4-5
4-7
6-1
6-2
2-2
7-1
4-10
1-12
1-13
4-3
7-3
7-3
4-8
4-1
4-12
7-8
4-2
4-6
7-5
1-4
1-4
7-8
1-2
1-7
7-7
7-9
7-8
1-3
1-5
7-6
7-10
7-1
1-2
1-1
4-4
7-10
1-11
4-14
7-10
2-3
2-3
2-3
2
7-4
1-9
1-8
7-1
7-10
2-3
4-9
Page 37
R402JWT
NO. PARTS CODE
[1] OVEN PARTS
ELECTRIC PARTS
1-1 FPWBFA417WRKZ AY 1-1 FPWBFA389WRKZ AW 1-2 FFS-BA033WRKZ -­1-2 FFS-BA037WRKZ AN 1-3 QFS-TA013WRE0 AG 1-4 QSW-MA085WRE0 AF 1-4 QSW-MA147WRZZ AG
!
1-5 RV-MZA346WRZZ BK
*
1-6 RTHM-A119WRE0 AK 1-6 RTHM-A075WRE0 AN 1-6 RTHM-A134WRZZ AK 1-7 FACCDA083WRE0 AQ 1-7 FACCDA085WREZ AQ 1-7 FACCDA103WREZ AQ 1-8 FH-DZA118WRKZ AN
!
1-9 RC-QZA211WRE0 AV
!
1-9 RC-QZA331WRZZ --
!
1-10 RMOTEA433WRZZ AX 1-10 RMOTEA346WRE0 AV 1-11 RLMPTA087WRZZ AL 1-11 RLMPTA082WRZZ AL 1-11 RLMPTA085WRZZ AL 1-12 RMOTDA264WRZZ AT 1-12 RMOTDA186WRE0 AW 1-13 RTRN-A746WRZZ BM
!
1-13 RTRN-A745WRZZ --
!
CABINET PARTS
2-1 GCABUA991WRPZ BH 2-1 GCABUB012WRPZ BH 2-2 GDAI-A390WRWZ BA 2-3 GLEGPA104WREZ AF
*
4-1 PHOK-A130WRFZ AK 4-2 LBNDKA163WRPZ AK 4-3 NFANJA053WRFZ AG 4-4 LANGTA419WRPZ AT
*
4-5 ************* -­4-6 MLEVPA244WRFZ AG 4-7 PCOVPA311WRE0 AG 4-8 PCUSGA532WRP0 AF 4-9 PCUSUA191WRP0 AC 4-10 PPACGA084WRF0 AE 4-11 PCUSUA410WRP0 AB 4-12 PCUSUA455WRP0 AD 4-13 PDUC-A610WRF0 AR 4-14 PDUC-A936WRFZ AV 4-15 PPACGA272WREZ AG
MISCELLANEOUS
6-1 FROLPA097WRKZ AN 6-2 NTNT-A108WREZ AW 6-3 TCAUAA292WRRZ AE 6-4 TCAUAA296WRRZ AH
SCREWS, NUTS AND WASHERS
7-1 XHPS740P08K00 AB 7-2 LX-CZA070WRE0 AC 7-3 LX-CZ0052WRE0 AA 7-4 LX-EZA042WRE0 AB 7-5 LX-EZA050WRE0 AB 7-6 XHPS730P06000 AB 7-7 XHPS740P08000 AB 7-8 XHTS740P08RV0 AG 7-9 XHTS740P12RV0 AC 7-10 XOTS740P10000 AB
PRICE
RANK
NEW
MARK
PAR T
RANK
DESCRIPTION
Noise filter assembly Noise filter assembly (Interchangeable) Monitor fuse 20A and monitor switch (V-5220Q) Monitor fuse 20A and monitor switch (D3V-1G-2C25) Temp. fuse 150C (Magnetron) Primary interlock switch/ door sensing switch Primary interlock switch/ door sensing switch (Interchangeable)
Magnetron
Thermal cut-out 145C (Oven) Thermal cut-out 145C (Oven) (Interchangeable) Thermal cut-out 145C (Oven) (Interchangeable) Power supply cord Power supply cord (Interchangeable) Power supply cord (Interchangeable) H.V. rectifier assy High voltage capacitor High voltage capacitor for production use (Interchangeable) Fan motor Fan motor (Interchangeable) Oven lamp Oven lamp (Interchangeable) Oven lamp (Interchangeable) Turntable motor Turntable motor (Interchangeable) Power transformer Power transformer for production use (Interchangeable)
Outer case cabinet [R-402JK-T] Outer case cabinet [R-402JW-T] Base plate Leg OVEN PARTS Latch hook H.V. capacitor band Fan blade Chassis support Oven cavity (Not a replacement part) Switch lever Waveguide cover Cushion Cushion TTM packing Cushion Cushion Fan duct MG duct Cushion
Roller assy Turntable Monitor caution DHHS caution label
Screw : 4mm x 8mm Special screw (Torx tamper proof screw) Special screw Special screw Special screw Screw : 3mm x 6mm Screw : 4mm x 8mm Screw : 4mm x 8mm Screw : 4mm x 12mm Screw : 4mm x 10mm
3
Page 38
R402JWT
[2] DOOR & CONTROL PANEL PARTS
5-8
5-4
5-3
5-1
5-7
5-2
5-6
3-1
5-5
3-5
3-1-3
3-1-1
3-2
3-1-2
6-7
3-5
3-4
6-5
3-3
Actual wire harness may be different from illustration.
6-6
4
Page 39
R402JWT
NO. PARTS CODE
[2] DOOR & CONTROL PANEL PARTS
CONTROL PANEL PARTS
3-1 FPNLCB902WRKZ BA 3-1 FPNLCB903WRKZ BA 3-1-1 PSHEPB179WREZ AT 3-1-1 PSHEPB180WREZ AT 3-1-2 QSW-KA063DRZZ AQ 3-1-3 GMADIA161WRFZ AK 3-2 JBTN-B359WRFZ AH 3-2 JBTN-B360WRFZ AH 3-3 MSPRCA157WREZ AF 3-4 DPWBFC531WRKZ BK 3-5 XEPS730P08XS0 AB
DOOR PARTS
*
5-1 FDORFA412WRTZ BF 5-2 PSHEPA336WRP0 AF
*
5-3 GWAKPB034WRRZ AX
*
5-3 GWAKPB036WRRZ AX 5-4 HPNL-A868WREZ AR 5-4 HPNL-A869WREZ AR
*
5-5 GCOVHA382WRF0 AM
*
5-6 LSTPPA139WRF0 AE 5-7 MSPRTA084WRE0 AB 5-8 LSTPPA167WRF0 AG
MISCELLANEOUS
6-5 FW-VZC094WREZ AS 6-6 FW-VZC093WREZ AN 6-7 TINSEB118WRRZ AM
PRICE
RANK
NEW
MARK
PAR T
RANK
DESCRIPTION
Panel sub assembly [R-402JK-T] Panel sub assembly [R-402JW-T] Key sheet [R-402JK-T] Key sheet [R-402JW-T] FPC Display window Open button [R-402JK-T] Open button [R-402JW-T] Open button spring Control unit Screw; 3mm x 8mm
Door panel Sealer film Door frame [R-402JK-T] Door frame [R-402JW-T] Door screen [R-402JK-T] Door screen [R-402JW-T] Choke cover Latch head Latch spring Door stopper
Main wire harness Filter harness Instruction book
5
Page 40
R402JWT
INDEX
PARTS CODE No.
DPWBFC531WRKZ 2-3-4 BK
FACCDA083WRE0 1-1-7 AQ
FACCDA085WREZ 1-1-7 AQ
FACCDA103WREZ 1-1-7 AQ
FDORFA412WRTZ 2-5-1 BF
FFS-BA033WRKZ 1-1-2 --
FFS-BA037WRKZ 1-1-2 AN
FH-DZA118WRKZ 1-1-8 AN
FPNLCB902WRKZ 2-3-1 BA
FPNLCB903WRKZ 2-3-1 BA
FPWBFA389WRKZ 1-1-1 AW
FPWBFA417WRKZ 1-1-1 AY
FROLPA097WRKZ 1-6-1 AN
FW-VZC093WREZ 2-6-6 AN
FW-VZC094WREZ 2-6-5 AS
GCABUA991WRPZ 1-2-1 BH
GCABUB012WRPZ 1-2-1 BH
GCOVHA382WRF0 2-5-5 AM
GDAI-A390WRWZ 1-2-2 BA
GLEGPA104WREZ 1-2-3 AF
GMADIA161WRFZ 2-3-1-3 AK
GWAKPB034WRRZ 2-5-3 AX
GWAKPB036WRRZ 2-5-3 AX
HPNL-A868WREZ 2-5-4 AR
HPNL-A869WREZ 2-5-4 AR
JBTN-B359WRFZ 2-3-2 AH
JBTN-B360WRFZ 2-3-2 AH
LANGTA419WRPZ 1-4-4 AT
LBNDKA163WRPZ 1-4-2 AK
LSTPPA139WRF0 2-5-6 AE
LSTPPA167WRF0 2-5-8 AG
LX-CZ0052WRE0 1-7-3 AA
LX-CZA070WRE0 1-7-2 AC
LX-EZA042WRE0 1-7-4 AB
LX-EZA050WRE0 1-7-5 AB
MLEVPA244WRFZ 1-4-6 AG
MSPRCA157WREZ 2-3-3 AF
MSPRTA084WRE0 2-5-7 AB
NFANJA053WRFZ 1-4-3 AG
NTNT-A108WREZ 1-6-2 AW
[ D ]
[ F ]
[ G ]
[ H ]
[ J ]
[ L ]
[ M ]
[ N ]
PRICE RANK
NEW
MARK
PART
RANK
PARTS CODE No.
[ P ]
PCOVPA311WRE0 1-4-7 AG
PCUSGA532WRP0 1-4-8 AF
PCUSUA191WRP0 1-4-9 AC
PCUSUA410WRP0 1-4-11 AB
PCUSUA455WRP0 1-4-12 AD
PDUC-A610WRF0 1-4-13 A R
PDUC-A936WRFZ 1-4-14 AV
PHOK-A130WRFZ 1-4-1 AK
PPACGA084WRF0 1-4-10 AE
PPACGA272WREZ 1-4-15 AG
PSHEPA336WRP0 2-5-2 AF
PSHEPB179WREZ 2-3-1-1 AT
PSHEPB180WREZ 2-3-1-1 AT
[ Q ]
QFS-TA013WRE0 1-1-3 AG
QSW-KA063DRZZ 2-3-1-2 AQ
QSW-MA085WRE0 1-1-4 AF
QSW-MA147WRZZ 1-1-4 AG
[ R ]
RC-QZA211WRE0 1-1-9 AV
RLMPTA082WRZZ 1-1-11 AL
RLMPTA085WRZZ 1-1-11 AL
RLMPTA087WRZZ 1-1-11 AL
RMOTDA186WRE0 1-1-12 AW
RMOTDA264WRZZ 1-1-12 AT
RMOTEA346WRE0 1-1-10 AV
RMOTEA433WRZZ 1-1-10 AX
RTHM-A075WRE0 1-1-6 AN
RTHM-A119WRE0 1-1-6 AK
RTHM-A134WRZZ 1-1-6 AK
RTRN-A746WRZZ 1-1-13 BM
RV-MZA346WRZZ 1-1-5 BK
[ T ]
TCAUAA292WRRZ 1-6-3 AE
TCAUAA296WRRZ 1-6-4 AH
TINSEB118WRRZ 2-6-7 AM
[ X ]
XEPS730P08XS0 2-3-5 AB
XHPS730P06000 1-7-6 AB
XHPS740P08000 1-7-7 AB
XHPS740P08K00 1-7-1 AB
XHTS740P08RV0 1-7-8 AG
XHTS740P12RV0 1-7-9 AC
XOTS740P10000 1-7-10 AB
PRICE
RANK
NEW
MARK
PART
RANK
COPYRIGHT © 2006 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced, stored in retrieval systems, or transmitted in anyform or by any means, electronic, mechanical, photocopying, re­cording, or other wise, without prior written permission of the publisher.
6
Loading...